Page 1
Household use only
The warranty excludes espresso machines that do not work or work incorrectly due to lack of cleaning,
failure to descale or due to the presence of foreign bodies in the grinder.
ESPRESSERIA AUTOMATIC
CCOONN SSUUMMEERR SSEERRVVIICCEE
UUSSAA :: 11--880000--552266--55337777
CCaannaaddaa :: 11--880000--441188--33332255
www.krupsusa.com
www.krups.ca
www.krups.com.mx
001188000011112288332255MMeexxiiccoo ::
* Actual model may vary slightly from photo
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page a1
Page 2
PAG E
2 IMPORTANT SAFEGUARDS
4 PRODUCT DESCRIPTION
5 WELCOME
Recipes
Limits to use
6 BEFORE FIRST USE
Measuring water hardness
Claris - Aqua Filter System cartridge
7-8 PREPARING THE MACHINE FOR FIRST USE
Programming your machine
Rinsing the machine
Adjusting the grinder
8-9 PREPARING ESPRESSO AND PRESSURE BREWED COFFEE
Preparing an espresso (from 0.7 to 2.4 oz / 20 to 70 ml)
Preparing ordinary coffee (from 2.7 to 7.4 oz / 80 to 220 ml)
2-cup function
9-10 U S I N G S TEAM
Frothing milk
Auto-Cappuccino Set
10 PREPARING HOT WATER
11 MAINTAINING YOUR MACHINE
Emptying the coffee grounds collector, the cleaning tray and the drip tray
Automatic cleaning program
12 AUTOMATIC DESCALING PROGRAM
General maintenance
13 OTHER FUNCTIONS
Maintenance
Settings
14 PRODUCT INFORMATION
Demonstration mode
Moving the machine
Electrical or electronic product at end of service life
15 PROBLEMS AND CORRECTIVE ACTIONS
16 LIMITED WARRANTY
CONTENTS
Actual model may vary slightly from photo
1
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 1
Page 3
2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, and/or injury to persons including the following :
1. Read all instructions prior to first use.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons, do not immerse cord,
plugs or machine in water or other liquid and keeps hands and utensils out of the
bean container while grinding and when the machine is plugged in.
4. Do not put water into the coffee bean container and/or under the servicing flap.
5. Not intented for use by children.
6. Close supervision is necessary when any machine is used near children. Keep
machine out of reach of children.
7. Burns can occur from touching hot surfaces, hot water or steam. Exercise caution.
8. Exercise caution when using the steam nozzle as steam can cause scalding.
9. Unplug machine from outlet as soon as you stop using it and when you clean it. Allow
to cool before putting on or taking off parts, before cleaning the machine, and before
storing.
10. All appliances are subjet to stringent quality control. Practical tests using appliances
taken at random are conducted and this may explain any slight marks or coffee
residue showing prior to use.
11. Do not operate any machine with a damaged cord or plug or after the machine
malfunctions, or has been damaged in any manner. Return machine to the nearest
Krups Service Center for examination, repair or adjustement.
12. To reduce the risk of injury do not drape cord over the counter top or table top where
it can be pulled on by children or tripped over unintentionally.
13. Do not let cord hang over edge of table or counter, or touch hot surfaces.
14. The use of accessory attachments not recommended by Krups may result in fire, elec-
tric shock or injury to persons.
15. Do not use outdoors.
16. Do not place on or near a hot gas or electric burner, or in a heated oven.
17. To disconnect the machine, turn the control to “off” then remove plug from wall
outlet. Do not yank cord, instead grasp plug and pull disconnect.
18. Do not use the machine for other than intended use.
19. Do not pour liquids other than water and descaling solutions specified in this manual
into the water tank.
20. Protect the machine against humidity and freezing.
21. This machine is intended for household use only.
SAVE THESE INSTRUCTIONS
CAUTION
This machine is intended for household use only. Any servicing other than cleaning and
user maintenance should be performed by the nearest authorized Krups Service Center.
Visit our website at www
.krups.com or contact our Consumer Service department for the
service center nearest to you.
To reduce the risk of fire or electric shock, do not dismantle the machine. Repair should be
done by an authorized Krups Service Center only.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 2
Page 4
3
SHORT CORD INSTRUCTIONS
AA..
We do not recommend using an extension cord with this device.
BB..
If an extension cord is absolutely necessary,
1) the marked electrical rating of the extension cord should be at least as great
as the electrical rating of the machine,
2) the longer cord should be arranged so that it will not drape over the counter
top or table top where it can be pulled on by children or tripped over.
CC..
This machine has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit into a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to modify the plug in any way.
In the interest of improving products, Krups reserves the right to change specifications
without prior notice.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 3
Page 5
4
Hot water button
OK validation button
Steam button
Rotating selection knob
Program settings button
“On/Off” button
Coffee grounds collector
Top view
Grinding fineness selector knob
Cleaning tablet pipe
DESCRIPTION
Cleaning tray
Water tank
Select (Rotate)
Confirm (Push)
Metal grinding wheel
Quick reference guide
Coffee outlets with height adjusting
handles
Water level floats
Steam nozzle
Knob
Cup warming tray
Coffee bean container
Coffee bean container lid
Drip tray grid
Digital display
Display screen
Water tank handle/lid
* Actual model may vary slightly from photos
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 4
Page 6
5
Congratulations and thank you for your purchase of this Krups Espresseria Automatic
espresso machine. We are confident you will enjoy the versatility of this machine as well as
the convenience. Should you have any questions, please contact one of our specially
trained consumer service managers. They are available Monday through Friday from 8:30
am to 6:30 pm (EST) at 1-800-526-5377 for the US, and Monday through Friday from
8:30 am to 4:30 pm (EST) at 1-800-418-3325 for Canada.
We strongly recommend that you register this product as quickly as possible to ensure that
the warranty program is validated. As an incentive to do so, we will extend the
customary 1 year warranty by 6 months when you complete the enclosed product
registration card.
Enclosed in this box is the Krups VIP Exclusive Service Kit. Within this kit, we have
included everything you need to get started. Each kit contains 1 packet of descaling
powder, 2 cleaning tablets, water hardness testing strip, a full color instruction manual, and
1 Claris water filter.
Here are some recipes you can make using your Espresseria Automatic:
• Cappuccino
For a cappuccino, the ideal proportions are as follows:
1/3 steamed milk, 1/3 espresso, 1/3 milk froth.
• Caffe Latte
To make coffee with milk, also often called Latte Macchiato,
the proportions are as follows: 3/5 steamed milk, 1/5 espresso,
1/5 milk froth.
For these milk-based preparations, it is best to use cold skimmed milk
straight from the refrigerator (ideally between 6 and 8° C).
WELCOME
RECIPES
LIMITS TO USE
This Espresseria Automatic machine must only be used to prepare espressos or coffee, to
froth up milk and heat liquids. This product has been designed for domestic use only. Any
commercial or professional use, inappropriate use or failure to comply with th instructions will
void the warranty.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 5
Page 7
To get the best tasting coffee and espresso and to extend your machine’s service life, we advise you to use the Claris - Aqua
Filter System cartridge enclosed with this machine.
This filter system reduces chlorine, impurities, lead, copper, pesticides, etc. that may be present in the water. Minerals and
trace elements will then be preserved.
6
Before using the machine for the first time, you will need to complete an initial set up procedure to ensure that the machine will
operate properly. You will be asked to set the water hardness level, language, clock, date, and a few other options. The digital
display will walk you through each step and the initial set up takes just a few minutes. Please note, if you disconnect the
machine from the power source, you will need to complete parts of this process again.
BEFORE FIRST USE
After 1 minute the hardness measurement will appear.
This is the number you will be asked to program into the machine.
Filter the water using the
Claris - Aqua Filter System
cartridge to reduce
carbonate hardness,
chlorine, lead, copper,
aluminium*.
Your machine will give you
a message telling you when
to replace your Claris Aqua Filter System
cartridge.
The Claris cartridge needs
to be replaced for about
every 50 litres of water or
every two months at least.
Fill a glass with the
water you normally use
and immerse the test
strip.
Degree of
hardness
0
very soft
1
soft
2
moderately hard
3
hard
4
extremely hard
°f
< 5,4° > 7,2° > 12,6° > 25,2° > 37,8°
°dH
< 3° > 4° > 7° > 14° > 21°
°TH
< 3,75° > 5° > 8,75° > 17,5° > 26,25°
1 sec.
012
3
4
MEASURING WATER HARDNESS
CLARIS - AQUA FILTER SYSTEM F 088 CARTRIDGE
* indications provided by the manufacturer
F 088
To install the water filter,
simply screw it into the
water tank.
Be sure to set the
date of installation for
reference in the future.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 6
Page 8
7
Pull out and fill the
water tank with fresh
water.
Select (rotate)
Confirm (push)
Replace the tank, press
firmly to insure its fitted
properly. Close the lid.
Open the coffee bean
container lid. Add fresh
coffee or espresso beans.
Close the coffee bean
container lid again.
Check that the coffee beans do not contain any foreign particles, as any damage caused by the presence of
foreign particles will void the warranty.
Do not put water into the coffee bean container.
Remember to fit the drip tray to avoid waste water flowing onto the work surface and staining it or scalding you.
Be sure that the drip tray is properly installed to avoid overflow.
Do not fill the water tank with hot water, mineral water, milk or any other liquid. If you turn on the machine when the
water tank is not in place or not correctly filled (under the “min.” level,), the “fill water tank” light will come on.
This machine will not operate when the tank is empty.
Never put ground coffee in the coffee container.
When you first use your machine, it will ask you to set several parameters. If you disconnect your machine, you will again be
asked for some of these parameters.
Use the selector knob
to choose a language
(highlighted). Press the
OK key to validate.
Press “On / Off” to turn
your machine on. Follow
the instructions that
appear on the “choice of
language” screen.
Use the selector knob to choose a function and increase
or reduce values. Confirm your choice using the OK key.
PREPARING THE MACHINE FOR FIRST USE
PROGRAMMING YOUR MACHINE
The machine will ask you to set:
Language
Measurement unit
Date
Clock
Auto-off
Auto-on
Water hardness
Filter
You can select your chosen language from those offered.
Choose either ml or oz as your measurement unit.
You can set the date (mandatory if you use the Claris - Aqua Filter
System cartridge).
You can choose between 12 hour or 24 hour time display.
You can choose the period after which your machine will stop
automatically, from 30 minutes to 4 hours (by 30 minute increments).
You can automatically start pre-heating of your machine at your
chosen time.
You must set your water hardness between 0 and 4. See “Water
hardness measurement” section.
You must indicate whether a filter has been installed or not
(Claris - Aqua Filter System cartridge).
Take care when using oily espresso / coffee beans as excessive oil may clog the machine or grinder.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 7
Page 9
8
You can rinse the system once
the machine has been turned
on and pre-heating has been
completed.
Place a medium cup under the coffee
outlets then select “YES” from the
menu proposed.
The rinsing cycle will stop automatically
after about 1.3 oz / 40 ml.
Press button at any time to display menus to perform rinsing and then select MAINTENANCE => OK => RINSING.
You should periodically rinse the machine. We recommend for instance rinsing the machine if it has not been used for several
days. Use a large cup, choose the “Yes” option in the rinsing function and follow the instructions on the screen.
There are three fineness settings on this grinder. You can adjust the fineness to select your own personal preferences.
The finer the grind, the stronger the flavor. To change the grind, turn the knob during the grinding process.
CHANGE THE SETTING DURING GRINDING.
NEVER FORCE THE GRINDI NG FINE NESS SETTING BUTTON.
CARAMELIZED COFFEE (e.g. flavor of strawberry) CAN BLOCK THE G RINDER.
Turn counterclockwise for
a finer grind.
Turn clockwise
for a coarser
grind.
RINSING THE MACHINE
ADJUSTING THE GRINDER
PREPARING ESPRESSO AND PRESSURE BREWED COFFEE
YOUR MACHINE I S DESIGNED TO MAKE COFFEE AND ESPRESSO FROM COFFEE BEAN S ONLY.
When you first make coffee with the machine or after a prolonged period of non-use or a cleaning or
descaling procedures, a little steam and hot water will come out of the steam nozzle (priming).
Splashing or scalding may occur if the coffee outlets are set too high in relation to the size of the cups.
With a simple touch of a button, you can prepare 4 types of beverages : espresso, strong espresso, coffee and
strong coffee.
AA mmoouunn tt ooff wwaatteerr
Espresso 0.7 - 2.4 oz / 20 - 70 ml
Strong Espresso 0.7 - 2.4 oz / 20 - 70 ml
Coffee 2.7 - 7.4 oz / 80 - 220 ml
Strong Coffee 2.7 - 7.4 oz / 80 - 220 ml
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 8
Page 10
9
Press the on/off button , wait for the end of pre-heating and perform a rinsing operation if you wish.
You can change the
volume of water at any
time using the rotating
knob.
Use the rotating button
to select your choice
and confirm by pressing
the OK button.
The selection menu will
be displayed.
PPlleeaassee nnoottee ::
The ground coffee is first moistened with a little hot water after the grinding stage. This is called
“pre-brewing” and it optimizes the brewing process by ensuring that the grounds are evenly wet.
A few moments later, the full brewing cycle begins.
You can use your machine to make 2 cups of coffee or espresso by cycling the machine twice. Remember not to remove
the cups after the first cycle.
Put two cups under the
coffee outlets.
You can lower or raise the
coffee outlets to suit the
size of your cups.
Put a cup under the coffee
outlets.
You can lower or raise the
coffee outlets to suit the
size of your cups.
Select your drink and confirm
by pressing the OK button
twice. A message will appear
to tell you that you have
chosen two cups.
If the drip tray is full or the water tank is empty after preparing the first coffee, the second cycle will not function.
You will then have to restart your second cycle after you have emptied the tray and refilled the water tank.
The machine will
automatically
sequence through
two complete cycles.
To stop coffee flowing into the cup, you can either again press “OK” or turn the rotating button to reduce
volume.
x 2
TWO-CUP FUNCTION
There is a temperature setting function to control how hot your coffee is (see Settings).
USING STEAM
Steam is used to froth milk (for cappuccino / latte) but can also be used to reheat other liquids. As you need a higher
temperature to produce steam than to make an espresso, the machine runs an additional pre-heating phase for steam.
When the screen displays the selection menu, press the “steam” key . The screen will
inform you that the machine is being pre-heated. Once the pre-heating phase has been
completed, a message will ask you to place a container under the steam nozzle. Press the
“steam” key again to start generating steam. A little water will be produced first and
then steam will start. Use the same key to stop steam generation.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 9
Page 11
10
FROTHING MILK
We recommend the use of cold, fresh milk (1% or 2% is best).
The milk and the frothing container must be very cold to produce the best results.
We therefore advise you against putting the container under hot water before using it.
Check that the steam
nozzle is correctly
fitted.
Fill a frothing pitcher
one-third and immerse
the nozzle in the milk.
Press the “steam” button
and follow the
instructions on the screen.
Once your milk is frothy
to your liking…,
again press the “steam”
button to stop the
cycle.
To remove any remaining
milk from the steam
nozzle, place a cup under
the nozzle and press the
hot water button .
Run for at least 10
seconds, then again
press the button to
stop generation.
To interrupt the steam function, just press any button.
If the nozzle is blocked, clean it out with a fine needle.
The maximum duration for production of steam per cycle is limited to 2 minutes.
AUTO-CAPPUCCINO SET XS 6000 (SOLD SEPARATELY)
The auto-cappuccino accessory makes it easy to
prepare a cappuccino or a caffe latte. It comprises
a special nozzle with two-positions / markings
and a brushed stainless steel milk jug and tubes.
Just join the various components to each other
(photo on left) and put your cup or glass under
the autocappuccino nozzle.
Don’t forget to clean thoroughly all parts of this
accessory (photo right).
You can also use our special XS 4000 liquid cleaner for milk systems.
XXSS 66000000 XXSS 44000000
You can remove the steam nozzle for thorough cleaning. Wash it
using a brush with water and a little non-abrasive dish soap.
Rinse and dry it. Before re-fitting, make certain that the air inlet
holes are not clogged by milk residues. If necessary clean out
the holes with the needle delivered with the machine.
PREPARING HOT WATER
While the screen displays the drink selection menu, press the “hot water” button .
A message will invite you to place a recipient under the steam nozzle. Again press
the “hot water” button to produce hot water.
To interrupt the hot water function, just press any button. If the nozzle is blocked, clean it out with a fine needle.
The maximum amount of hot water per cycle is limited to 10 oz.
TToo pprreevveenntt tthhee mmiillkk ddrryyiinngg oonn aanndd iinn tthhee aauuttoo--ccaappppuucccciinnoo aacccceessssoorryy wwee ssttrroonnggllyy rreeccoommmmeenndd ttoo iimmmmeeddiiaatteellyy ::
-- ppuutt cclleeaarr wwaatteerr iinnssiiddee tthhee jjuugg aanndd rreeiinnssttaa llll tthhee ddiiffffeerreenntt ccoommppoonneennttss
-- llaauunncchh aa ““sstteeaamm”” ccyyc
cllee
-- cclleeaann aallll ppaarrttss wwiitthh aa mmooiisstt ccllootthh..
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 10
Page 12
11
If the above message
appears, remove, empty
and clean the drip tray.
The drip tray receives residual water and the coffee grounds collector receives used coffee grounds.
The coffee cleaning tray allows you to eliminate any deposits of coffee grounds above the percolation chamber.
Remove, empty and
clean the coffee
grounds collector.
The drip tray is equipped
with floats to tell you
when to empty it.
The warning message will remain displayed if the coffee grounds collector is not inserted correctly.
If the coffee grounds collector is inserted within less than 8 seconds, the machine will ask you to confirm that you
have correctly emptied it. You cannot make espresso or coffee while the warning message is displayed.
The coffee grounds collector has a maximum capacity of 12 coffee cakes.
MAINTAINING YOUR MACHINE
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
Remove the coffee
cleaning tray.
Clean it under water
and dry thoroughly
before re-inserting.
EMPTYING THE COFFEE GROUNDS COLLECTOR, THE COFFEE CLEANING TRAY AND THE DRIP TRAY
RINSING THE SYSTEM - SEE “BEFORE FIRST USE” SECTION
AUTOMATIC CLEANING PROGRAM – TOTAL DURATION: ABOUT 20 MINUTES
You should perform the cleaning program after every 350 preparations of espresso or coffee.
The machine will let you know automatically on the display screen.
Caution! To benefit from the warranty conditions, it is essential to perform the machine cleaning
cycle when informed to do so. Be sure to follow the order of operations.
You can continue to use the machine, but you are advised to perform the program as soon as possible.
To perform the cleaning program, you will need a container with a minimum capacity of 2.0 oz and a Krups XS 3000
cleaning tablet.
The automatic cleaning program
is in three parts – the cleaning
cycle itself, then 2 rinsing cycles.
This program lasts about 20
minutes.
Press button to perform
cleaning at any time and then
choose MAINTENANCE => OK
=> CLEANING from the menus
displayed.
Press the button
to start the automatic
cleaning program when
the “Cleaning needed”
message is displayed.
Just follow the
instructions
shown on the
screen.
If you press the ‘On/Off’ key during cleaning or in the event of power failure, the cleaning program will start
again right from the beginning. You will not be able to postpone this operation. This is essential due to water
system rinsing reasons. In this case, you will need to use another cleaning tablet. Be sure to complete the entire
cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning solutions are accidently swallowed).
The cleaning cycle is a discontinuous cycle. Do not put your hands under the coffee outlets during the cycle.
Only use Krups XS 3000 cleaning tablets. We cannot be held responsible for any damage that may result
from the use of tablets from other brands.
You can obtain cleaning tablets from Krups Service Centers.
Make certain to protect your work surface during cleaning cycles, especially if they are made of
marble, stone or wood.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 11
Page 13
12
AUTOMATIC DESCALING PROGRAM – TOTAL DURATION: ABOUT 22 MINUTES
The quantity of scale deposited depends on the hardness of the water used. The machine will automatically warn you with a
message when you need to proceed with descaling.
To perform the descaling program, you will need a container with minimum capacity of 2.0 oz and a Krups F 054 (40 g)
descaling powder.
The descaling program is in three parts – the descaling cycle itself, then 2 rinsing cycles.
Press button to perform descaling at any time and then choose MAINTENANCE => OK => DESCALING from the
menus displayed.
Caution! To benefit from the warranty conditions, it is essential to perform the machine descaling
cycle when the machine tells you to do so. Be sure to follow the order of operations.
You can continue to use the machine but you are advised to perform the operation as soon as possible.
Press the button to start the automatic descaling program when this message is
displayed.
Clean the cleaning tray, the drip
tray, the coffee grounds collector
and the drip tray grid with hot
water and a liquid detergent.
Rinse the water tank
with fresh water.
Only use Krups descaling products. You can obtain descaling products from Krups Service Centers.
Do not use conventional starchy sulphonic acid or other products containing acid.
The manufacturer may not be held responsible for damage to the machine through use of cleaners or descalers
not specifically recommended.
Be sure to complete the entire descaling cycle to avoid any risk of intoxication.
Do not put your hands under the coffee outlets during the cycle.
Make certain to protect your work surface during descaling cycles, especially if they are made
of marble, stone or wood.
Just follow the instructions shown
on the screen, making sure the
powder dissolves fully.
If the coffee grounds collector is not fitted you will be warned by a message being displayed.
Fit the collector again for the cycle to continue automatically.
If a power failure occurs during the cycle, you will have to start it again right from the beginning.
You will not be able to postpone this operation.
GENERAL MAINTENANCE
Always remove the power supply cord from the socket and let your machine cool down before cleaning it.
Do not use utensils or cleaning products likely to scratch or corrode the machine.
Wipe the body of the machine on the outside using a moist cloth.
If your product is equipped with our Claris - Aqua Filter System cartridge F088, please remove this
cartridge during the descaling operation.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 12
Page 14
13
You can use all the following options to start selected programs. Then follow the instructions on screen
Maintenance
Settings
Product information
Demonstration
Quit
PPRROOGG
MAINTENANCE
Rinsing
Cleaning
Descaling
Filter
Quit
MMAAIINNTTEENNAANNCCEE
Press the knob from the beverage selection screen to access the machine’s other menu functions. Use the rotating
button to browse through menus and options for all settings and validate your choice using the OK button. Press the
button to cancel a choice and go back to the beverage selection menu.
To access maintenance
To access settings
To access product information
To access demonstration mode
To quit / exit
To access rinsing
To access cleaning
To access descaling
To access filter mode: install, change or
remove your Claris - Aqua Filter System
cartridge
To return to the previous menu
OTHER FUNCTIONS: KNOB
SETTINGS
Language
Screen contrast
Date
Clock
Auto-off
Auto-on
Measurement unit
Water hardness
Coffee temperature
Quit
OOPPTTIIOONNSS
You can select your chosen language from those offered.
You can set screen contrast for comfort.
You need to set the date, especially if you use an anti-scale
cartridge.
You can choose between 12 hour or 24 hour time display.
You can choose the period after which your machine will turn
off automatically, from 30 minutes to 4 hours in 30 minute
increments.
You can automatically start pre-heating of your machine at
your chosen time.
Choose either ml or oz as your measurement unit.
You must set your water hardness between 0 and 4. See
“Water hardness measurement” section.
You can set the temperature of your espresso or coffee to one
of three levels.
To return to the previous menu.
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 13
Page 15
14
Coffee cycles
Water cycles
Steam cycles
Rinsing
Cleaning
Last
Last
Last
Next
Clean
Descaling
Next
Descaling
Filter information
Next
Fit
PPRROODDUUCCTT
II NNFFOORRMMAATTIIOONN
PRODUCT INFORMATION
* You must first have correctly installed a filter through the program accessible via MAI NTENANCE => FILTER =>
INSTALL before being able to access the first two options of the filter information sub-menu.
Displays the total number of coffees the machine has made.
Displays the total number of hot water cycles the machine has
performed.
Displays the total number of steam cycles the machine has
performed.
Displays the total number of rinsing cycles the machine has
performed.
Displays the total number of coffees made
since last cleaning.
Displays the number of coffees that can be
made before next cleaning.
Starts the cleaning program.
Displays the total number of coffee
equivalents made since last scale removal.
Displays the number of coffee equivalents
that can be made before next scale removal.
Starts the scale removal program.
Displays the date of the last filter change*
and the quantity of water that has run through.
Displays the date for the next filter change*
and the quantity of water to run through.
Starts the filter change procedure.
DEMONSTRATION MODE
When this mode is activated and the screen displays the drink selection menu, the machine will scroll the various functions
available at regular intervals, so you can access them.
Use this sub-menu to disable or activate this function.
MOVING THE MACHINE
Keep the original packaging and use it again to move the machine.
If the unpacked machine is dropped, it is advisable to take it back to an authorized service center to avoid any
risk of fire or electrical problems.
Let’s all help protect the environment!
Your machine contains many recyclable materials that can be re-used.
Please recycle.
ELECTRICAL OR ELECTRONIC PRODUCT AT END OF SERVICE LIFE
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 14
Page 16
15
TROUBLESHOOTING GUIDE
The machine fails to come on when you
press the On/Off key.
The espresso or coffee is not hot enough.
The coffee is too weak or not strong
enough.
The coffee flows too slowly.
The coffee is not creamy enough.
You used ground coffee instead of coffee
beans.
The coffee does not come out of the outlet
holes.
The grinder makes a strange noise
The grind setting button of the mill is hard
to turn
Steam does not come out of the nozzle.
Not enough froth on the milk.
The milk froth is too bubbly
The Auto-Cappuccino accessory does not
suck in the milk (accessory sold separately).
You have filled the water tank, but the
warning message remains displayed.
The cleaning program refuses to start.
The scale removal program refuses to start.
You have emptied the coffee grounds
collector, but the warning message remains
displayed.
You have washed the cleaning tray, but the
warning message remains displayed.
A power failure occurred during a cycle.
There is water or coffee under the machine.
A “Fault No. XX” message appears.
Check that the power supply cord plug is correctly inserted in the socket.
Pre-heat the cups by rinsing them in hot water or under the steam nozzle.
Change the coffee temperature setting.
Check that the coffee bean container contains sufficient coffee.
Reduce the volume of coffee selected using the rotating knob.
Select the strong coffee button.
Turn the grinding fineness button to the left to obtain a finer grind.
Turn the grinding fineness button to the right to obtain a coarser grind (may
depend on the type of coffee used).
Turn the grinding fineness button to the left to obtain a finer grind(may depend
on the type of coffee used). Ensure coffee beans are fresh.
Use your vacuum cleaner to remove the ground coffee in the coffee bean
container.
The outlet hole may be blocked by dry coffee. Use a fine needle to clear the
holes. Rinse the machine and try again.
There may be foreign bodies in the grinder or not enough beans. Check that
the container is full and free of foreign bodies.
Contact your Krups Service Center.
Change the mill setting only when the grinder is in operation.
First turn off your machine and let it cool down:
- Clean out the outlet hole with a needle
- Clean out the steam nozzle support pipe with a needle. Run a hot water cycle
Check that the steam is able to come out of the nozzle and dry the hole.
Use a recipient and cold milk at the temperature it comes out of the
refrigerator. Change the type or brand of milk as appropriate.
We recommend 1% or 2% milk.
Check that the two ends of the small stainless steel tube fit correctly into the
steam nozzle seal.
Check that the tube immersed in the milk is not blocked.
Check for correct joining of the flexible tube with the accessory to avoid any
air leakage.
First turn off your machine and let it cool before clearing the Auto-Cappuccino
accessory outlet hole.
Check for correct positioning of the tank in the coffee maker.
Check that the float at the bottom of the tank moves freely.
Rinse the accessory and if necessary remove scale.
Disconnect the machine for a few moments then turn on again.
Disconnect the machine for a few moments then turn on again.
Remove the collector, make certain that it is empty, wait for 8 seconds and
then fit it again.
Check that the collector is correctly pushed in.
Remove the tray, wait 8 seconds and then fit it again.
Check that the cleaning tray is correctly pushed in.
The machine will re-initialise automatically when power is turned on and be
ready for a new cycle.
The drip tray is overflowing. Empty and clean the cleaning tray.
Check for correct positioning of the drip tray.
Disconnect the machine for a few moments then bring it back into service.
If the failure persists, note the fault number and contact the Krups Service
Center.
PPRROOBBLLEEMM
RREECCOOMMMMEE NNDDAATTIIOONN
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 15
Page 17
16
LIMITED WARRANTY
This Krups product is warranted for 1 year from the date of purchase against defects in
material and workmanship with a maximum of 3000 cycles. These appliances are not
suitable for commercial or professional use. During this period, the Krups’ product that,
upon inspection by Krups, is proved defective, will be repaired or replaced, at Krups’
option, without charge to the customer. If a replacement product is sent, it will carry the
remaining warranty of the original product. This warranty does not apply to any defect arising from a buyer’s or user’s misuse of the product, negligence, failure to follow Krups’ instructions, use on current or voltage other than that stamped on the product, wear and tear,
alteration or repair not authorized by Krups, or use for commercial purposes.
THE WARRANTIES SET FORTH HEREIN ARE EXCLUSIVE AND NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE MADE
BY KRUPS OR ARE AUTHORIZED TO BE MADE WITH RESPECT TO THE PRODUCT.
Same states do not allow limitation on how long an implied warranty lasts or do not allow
the exclusion of incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
If you believe your product is defective, bring the product (or send it, postage prepaid)
along with proof of purchase to the nearest authorized Krups Service Center. (Please
contact your respective country’s customer service department, indicated below, for the
address of the nearest authorized Krups Service Center).
If you send the product, please include a letter explaining the nature of the claimed defect.
IIff yyoouu hhaavvee aaddddiittiioonnaall qquueessttiioonnss,, pplleeaassee ccaallll oouurr CCoonnssuummeerr SSeerrvviiccee DDeeppaarrttmmeenntt ::
UUSSAA :: 11--880000--552266--553
37777;;
MMoonn -- FFrrii 88::3300 aa..mm.. -- 66::3300 pp..mm.. ((EESSTT))..
wwwwww..KKrruuppssUUSSAA..ccoomm
Please note hours are subject to change.
Before calling the Consumer Service Department, please have the product code located
on the bottom of the unit available. This will assist us in answering your questions. It is
helpful if you have the machine available at the time of your call.
General correspondence can be addressed to :
USA :
Krups
196 Boston Avenue
Medford, MA 02155
OOnnllyy lleetttteerrss ccaann bbee aacccceepptteedd aatt t
thhiiss aaddddrreessss.. SShhiippmmeennttss aanndd ppaacckk aaggeess tthhaatt ddoo nnoott
hhaavvee aa rreettuurrnn aauutthhoorriizzaattiioonn nnuummbbeerr wwiillll bbee rreeffuusseedd..
C
Caannaaddaa :: 11--880000--441188--33332255;;
MMoonn -- FFrrii 88::3300 aa..mm.. -- 44::3300 pp..mm.. ((EESSTT))..
wwwwww..KKrruuppss..ccaa
Canada :
Groupe SEB Canada Inc.
455 Finchdene Square
Scarborough, Ontario M1X 1B7
FALC DISP USA dernière version 7220.qxp 7/06/06 9:56 Page 16
Loading...