KROHNE BM702 User Manual
© KROHNE 12/2000
Remote Operation
Instructions
HART Communicator 275
Asset Management Solutions (AMS)
BM 70 A/P, BM 700, BM 702
KROHNE Messtechnik GmbH & Co. KG · Ludwig-Krohne-Str. 5 ! D-47058 Duisburg
Tel.: 0203-301 0 ! Fax: 0203-301 389 · e-mail: krohne@krohne.de
1/10
Remote Operation Instructions BM 70 A/P, BM 700, BM 702 HART
1 General Information 3
1.1 Configuring Instruments for Multidrop 3
2 IDs and Revision numbers 3
3 Implementation Peculiarities 3
4 HART Communicator 275 (HC275) 4
4.1 Installation 4
4.2 Operating 4
4.3 Known HC275 (4.9) Shortcomings 4
5 Asset Management Solutions (AMS) 4
5.1 Installation 4
5.2 Operating 5
5.3 Known AMS (5.0) Shortcomings 6
KROHNE Messtechnik GmbH & Co. KG · Ludwig-Krohne-Str. 5 ! D-47058 Duisburg
Tel.: 0203-301 0 ! Fax: 0203-301 389 · e-mail: krohne@krohne.de
2/10
Remote Operation Instructions BM 70 A/P, BM 700, BM 702 HART
1 General Information
The BM 70 A/P, BM 700, BM 702 are all the two-wire transmitters with 4..20mA current output and HART® capability.
General characteristics of the BM70 X HART® interface:
•
Multidrop Mode is supported.
•
Burst Mode is not supported.
Electrical connection (point-to-point or multidrop): refer to sections 4.1 – 4.4 of the
Instructions. BM 70 A/P, BM 700, BM 702“.
„Installation and Operating
1.1 Configuring Instruments for Multidrop
There are differences in configuring instruments for multidrop mode from remote or via device local keypad.
•
If the instrument is entering multidrop via HART® interface (any application can be used), i.e. its bus address is
changed from ‘0’ to any allowed, then all the necessary operation with the instrument current output are done
automatically (by the HART® transm itter) .
•
If the instrument local keypad is used, the user must manually carry out the three assignments:
1. Set the desirable bus address (Fct. 3.3.6),
2. Set the current output range to “4 – 20 mA” (Fct. 3.3.2),
3. Switch the current output function to “Off” (Fct. 3.3.1) and store configuration.
2 IDs and Revision numbers
The HART Device Descriptions described in this document have the following IDs and revision numbers:
Manufacturer ID: 69 (0x45)
Device Type: 249 (0xF9)
Device Revision: 11 (0x0B)
DD Revision: 2
HART Universal Revision: 5
HC 275 OS Revision:
AMS Version:
≥
≥
4.9
5.0
For information about Transmitter Revisions and related Device Descriptions refer to the KROHNE HART Device
List.
3 Implementation Peculiarities
As for all previous BM 70 X DD revisions there are some implementation peculiarities, caused by either restrictions of
the DDL / AMS or introduced deliberately – to restrict the usage/access to some device functionality.
The list of implementation peculiarities/restrictions follows:
•
The values in the
unchanged in operation. The user should not have access to these values. Therefore the service data is made
inaccessible for offline device configuration (it is open for live device provided the user is capable to get
authorization as specia list) .
•
The
•
The BM 70 A/P /700 /702 HART® transmitter interacts with the instrument mastering SW via special interface
Conversion Table
functions. Their actual set impose some display-related restrictions: functions
of the display) and
display submenu (3.2) is left out (i.e. is not maintained by the instrument HART® application layer) – the local
instrument user might configure the display settings without any impact on the remote HART® bus master.
Hence one important consequence must be pointed out: the units for measurements on HC275 screens/AMS
faceplates coincide with the ones for configuration parameters (say, for ‘Level’ measurements – with the units for
‘Tank height’, ‘Block distance’, etc.) but not with the ones that are set via display menu (3.2.2, 3.2.3). If the user
Service
KROHNE Messtechnik GmbH & Co. KG · Ludwig-Krohne-Str. 5 ! D-47058 Duisburg
Tel.: 0203-301 0 ! Fax: 0203-301 389 · e-mail: krohne@krohne.de
menu are generally set by Krohne or possibly by the Service technician, and remain
is excluded from offline data for HC275 whilst for AMS it is possible to configure it offline.
Test Display
Display Firmware
(2.4.2) are not supported by the HART® interface. Besides, the complete
(2.1.2 – tests the HW
3/10
Loading...