KitchenAid KUDS01FLSS, KUDS01FLBT, KUDS01FLBL, KUDS01DLWH, KUDS01DLSS Dimension Guide

® Undercounter Dishwasher

PRODUCT MODEL SERIES		OVERALL DIMENSIONS
KUDC01TM	KUDP01FL	*For models using a 3/4"			3/4" (1.9 cm) insulation –
		(1.9 cm) custom wood front	3/4" (1.9 cm) insulation –
KUDI01DL	KUDP01IL	panel, this dimension is			may be compressed
			may be compressed		(not used on all models)
KUDI01FL	KUDS01DL	24-3/4" (62.9 cm).	(not used on all models)
				top vent	24-7/8" (63.2 cm)	front vent
KUDI01IL	KUDS01FL	23-7/8" (60.6 cm)	24-1/2" (62.2 cm)*	model	24-1/2" (62.2 cm)*	model
KUDK01IL	KUDS01IL
KUDL01IL	KUDS01VM
KUDP01DL
				33-7/8"		33-7/8"
Electrical: 120-volt, 60 Hz, AC-only, 15 or				(86 cm) min.		(86 cm) min.
				with wheels		with wheels
20 amp electrical supply. Use copper wire only. A				removed		removed
time-delay fuse or circuit breaker and separate
circuit is recommended.
Water: A hot water line with 20-120 psi
(138-862 kPa) water pressure. Water temperature
must be minimum 120°F (49°C) at dishwasher.			21" (53.3 cm)		21" (53.3 cm)
Use 3/8" O.D. copper tubing with compression		CABINET OPENING DIMENSIONS
fitting or flexible stainless steel braided fill line
(1/2" minimum plastic tubing is optional but not
recommended). Use a 90° elbow with 3/8" N.P.T.
external pipe threads on one end to connect to
water inlet valve. Do not solder within 6" (15.2 cm)
from water inlet valve.
Drain: Use the new drain hose supplied with your			24" (61 cm)**
dishwasher. If this is not suitable, use a new drain
hose with a maximum length of 12 feet (3.7 m)			All surfaces must be free
that meets all current AHAM/IAPMO test
			from intrusions
standards, is resistant to heat and detergent, and					24" (61 cm)
fits the drain connector of the dishwasher. Must
					min.
have a high drain loop 20 inches (50.8 cm) above					34" (86.4 cm) min.*
the subfloor or floor. Connect drain hose to waste		3-1/4"			3-1/4"
tee or disposer inlet above drain trap in house
		(8.3 cm)			(8.3 cm)
plumbing and 20 inches (50.8 cm) minimum			5-1/2"
above the floor. An air gap must be used if the		2"	(14 cm)		2"
drain hose is connected to house plumbing lower		(5.1 cm)			(5.1 cm)
than 20 inches (50.8 cm) above subfloor or floor.		6" ***
Use 1/2" minimum I.D. drain line fittings.					6" ***
		(15.2 cm)
					(15.2 cm)

Corner installation: Allow 2" (5,1 cm)

minimum between corner wall and dishwasher

2"

opening.

9"

(5.1 cm)

10"

(22.9 cm)

Grommet is required for electrical cable or power

2-3/4" 3-1/4"

(25.4 cm) 3-1/4"

2-3/4"

supply cord hole cut in a metal cabinet.

(7 cm) (8.3 cm)

(8.3 cm)

(7 cm)

Do not install dishwasher over carpeted floor.

Water line should enter through the

Drain hose and power supply line should enter through the

Unit accepts custom door panels.

left side of opening in shaded areas.

right side of opening in shaded areas.

Minimum 1/2" (12,7 mm) hole.

Drain hose size: 1-1/2" (3.8 cm)

Power supply line hole-direct wired: 3/4" (1.9 cm)

Power supply line hole-with plug: 1-1/2" (3.8 cm)

*Measured from the lowest point on the underside of countertop.

May be reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.

**Minimum, measured from narrowest point of opening.

***May be increased to 6-5/8" (16.6 cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point.

CUSTOM FRONT PANEL DIMENSIONS

Top Vented Models

23-1/2" (59.7 cm)	30-3/16" (76.7 cm)

A custom front panel must weigh no more than 16 pounds and must be made to these dimensions.

3/4" (19.1 mm)

Front Vented Models

1/8 (3.2 mm)

Front View

*25

-

29/32

(65.8

cm)

1/8

front

(3.2 mm)

Side

View

23-3/8

3/4

(59.4 cm)

(1.9 cm)

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. 8531880
Instructions packed with product. Specifications subject to change without notice.	07-13-04