|
® |
30" Freestanding and Slide-In Gas Range |
|
||||
PRODUCT MODEL NUMBERS |
|
OVERALL DIMENSIONS |
|
|
|
||
KGRT600H |
KGST300H |
|
|
|
|
|
|
KGRT607H |
KGST307H |
|
|
Slide-in Range |
IMPORTANT: |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
Rear vent must be installed |
|
|
|
|
|
|
|
on all slide-in models for |
|
|
|
|
|
|
|
proper ventilation. |
|
|
|
|
|
1-1/2" |
30" (76.2 cm) |
|
|
|
Gas supply: Use 3/4" rigid pipe gas supply |
(3.8 cm) |
|
|
|
|||
|
rear vent width |
|
|
|
|||
line to the range location. A smaller size pipe on |
|
|
|
|
|
||
long runs may result in insufficient gas supply. |
|
|
|
|
|
||
With L.P. gas, piping or tubing size can be 1/2" |
|
|
|
|
Freestanding |
||
minimum. If local codes permit, it is |
|
|
|
36-1/8" |
30" (76.2 cm) |
||
|
|
|
(91.8 cm) |
Range |
|||
recommended that new flexible metal tubing, |
|
|
range width |
||||
|
|
cooktop |
|||||
|
|
|
|
||||
design-certified by AGA or CSA, 4-5 feet long, |
|
|
height |
|
|
||
|
|
8-1/4" |
|
|
|||
1/2-inch or 3/4-inch I.D., be used for connecting |
|
|
|
|
|||
|
|
(21 cm) |
|
|
|||
the range to the rigid gas supply line. A 1/2" |
|
|
|
|
|
||
male pipe thread is needed for connection to |
|
|
|
|
|
||
pressure regulator female pipe threads. An |
|
|
|
|
36-1/8" |
||
easily accessible individual manual shutoff valve |
|
|
|
|
|||
|
|
|
|
(91.8 cm) |
|||
must be located in the same room, but external |
|
1" |
|
|
cooktop |
||
|
|
|
height |
||||
to the range. |
|
|
|
(2.54 cm) |
|
|
|
|
|
|
spacer |
|
|
|
|
Electrical: 120-volt, 60 Hz, AC-only, 10 amp, |
|
|
30" |
|
44-3/8" |
||
|
|
|
(112.7 cm) |
||||
electrical supply, fused on both sides of the line. |
|
|
(76.2 cm) |
|
|
||
|
27-3/4" |
width |
|
|
|||
A separate circuit is recommended. A time-delay |
|
(70.5 cm) |
|
1" |
|
||
|
depth |
|
|
||||
fuse or circuit breaker is recommended. |
|
|
with |
|
(2.54 cm) |
|
|
|
|
|
spacer |
|
|||
|
|
|
|
handle |
|
|
|
|
|
|
|
|
|
27-3/4" |
|
|
|
|
|
|
|
(70.5 cm) |
|
|
|
|
|
|
|
depth |
|
SLIDE-IN RANGE COUNTERTOP PREPARATION |
|
|
with |
|
|||
|
|
handle |
|
The cooktop sides of the slide-in range fit over the cutout edge of your countertop.
If you have a square finish (flat) countertop and the opening width is 30", no countertop preparation is required.
Formed front-edged countertops: Must have molded edge shaved flat 1/2" from each front corner of opening.
Tile countertops may need trim cut back
1/2" from each front corner and/or rounded edge flattened.
If countertop opening width is greater than 30", adjust the 1/2" dimension.
Countertop must be level. Place level on countertop, first side to side; then front to back. If countertop is not level, range will not be level. Oven must be level for satisfactory baking conditions.
30" (76.2 cm) opening width
30-7/8"
(78.4 cm)
1/2" (1.3 cm)
Formed or tiled countertop trimmed 1/2" (1.3 cm) back at front corners of countertop opening.
22-5/8"
(57.5 cm)
Cooktop sides of range fit over edges of countertop opening.
CABINET OPENING DIMENSIONS
25" countertop depth and 24" base cabinet depth, 36" countertop height
Freestanding or Slide-in Range
4" (10.2 cm) min. clearance from both sides of range to side wall or other combustible material.
9" (22.9 cm)
Gas line opening
should be located 3" (7.6 cm) within this shaded area
Floor gas line opening if directly below regulator
2-1/2" (6.4 cm)
2" (5.1 cm)
*NOTE: 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than 1/4" (6.4 mm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.
|
13" (33 cm) max. |
|
|
|
|||||
|
|
|
|||||||
For minimum |
|||||||||
|
upper cabinet depth |
|
|
||||||
|
|
|
|
|
|
|
|
clearance to |
|
|
|
|
|
|
|
|
|
cooktop, see |
|
|
|
30" (76.2 cm) cabinet |
|
|
|
NOTE*. |
|||
|
|
opening width |
|
|
|||||
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
30" (76.2 cm) |
|
||||||||
opening width |
|
|
18"
(45.7 cm)
6" (15.2 cm)
2-1/2"
(6.4 cm)
10" (25.4 cm)
24" (61 cm)
7/8" (2.2 cm) min. required between cabinet opening and door or hinge opening
18" (45.7 cm) upper side cabinet to countertop
Outlet should be located within the 18" x 10"
(45.7 x 25.4 cm) shaded area
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation |
Ref. 9758571 |
Instructions packed with product. Specifications subject to change without notice. |
04-20-04 |