Kenwood BLM60 Series, BLM61 Series, BLP60 Series, BLP600, BLP607 Instruction Manual

...

Type BLP60, BLP61

English 2 - 12

Type BLM60, BLM61

instructions

´¸∂w

31 - 42

HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH

126672/1

BLP60 BLM60

BLP61 BLM61

햲

햳

햵

햶

햷

햸

햹

햺 햻

햽 햾 햿

BLP61/BLM61







햴





헀

햶

햷

햸

헁

헂





헃

헄

safety

Read these instructions carefully and retain for future reference.

Remove all packaging and any labels.

Switch off and unplug:

before fitting or removing parts;

when not in use;

before cleaning.

Never fit the blade unit to the power unit without the blender goblet or mill jar fitted.

Always unplug the appliance before putting your hands or utensils in the goblet.

Always take care when handling the blade assembly and avoid touching the cutting edge of the blades when cleaning.

Only operate the blender with the lid in place.

Only use the goblet with the blade assembly supplied.

Never let the power unit, cord or plug get wet.

Never use a damaged appliance. Get it checked or repaired: see ‘service and customer care’.

Never use an unauthorised attachment.

SCALD RISK: Hot ingredients should be allowed to cool to room temperature before blending.

Never leave the appliance unattended when it is operating.

When removing the blender or mill from the power unit:

wait until the blades have completely stopped;

don’t accidentally unscrew the goblet or mill jar/lid from the blade assembly.

Never run the blender empty.

Never blend more than the maximum capacity stated in the recommended usage chart.

To ensure long life of your blender or mill, do not run it continuously for longer than 60 seconds.

Smoothie recipes - never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the goblet.

Do not process hard spices such as Nutmeg or Turmeric root as they may damage the blade.

Do not use the blender as a storage container. Keep it empty before and after use.

Always use the blender on a secure, dry level surface.

Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.

This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.

Misuse of your blender can result in injury.

Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.

Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

The maximum rating is based on the attachment that draws the greatest load. Other attachments may draw less power.

safety

IMPORTANT: HOT BLENDING INSTRUCTIONS

To minimise the possibility of scalding when blending hot ingredients keep hands and other exposed skin away from the lid to prevent possible burns. The following precautions must be observed:

CAUTION: Blending very hot ingredients may result in hot liquid and steam being forced suddenly past the lid or filler cap

We recommend that hot ingredients are allowed to cool before blending.

NEVER exceed 1200ml / 5 cups capacity if processing hot liquids, such as soups (refer to the markings on the goblet).

ALWAYS commence blending at a low speed and gradually increase the speed. NEVER blend hot liquids by using the pulse setting.

Liquids which tend to foam such as milk, should be limited to a maximum capacity of 1000ml/4 cups.



Take care when handling the blender as the goblet and its contents will be very hot.

Take particular care when removing the lid. The lid is designed to be a tight fit to prevent leakage. If necessary protect your hands with a cloth or oven gloves when handling.

Ensure the goblet is securely attached to the base and when removing from the appliance, guide the base and ensure it is removed together with the goblet.

Ensure that the lid and filler cap are securely in place before every blending operation.

Always ensure that the vents in the filler cap are clear before every blending operation



When fitting the lid to the goblet always ensure that the lid and goblet rim are clean and dry to ensure a good seal and prevent spillage.

before plugging in

Make sure your electricity supply is the same as the one shown on the underside of the appliance.

Important - UK only

The wires in the cord are coloured as follows: Blue = Neutral Brown = Live.

The appliance must be protected by a 13A approved (BS1362) fuse.

Note:

For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).

If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

his appliance conforms to EC

T directive 2004/108/EC on

lectromagnetic Compatibility and

C regulation no. 1935/2004 of

E 27/10/2004 on materials intended

or contact with food.

se your blender for soups, drinks,

âtés, mayonnaise, breadcrumbs,

p biscuit crumbs, chopping nuts and crushing ice. Use your multi mill (if supplied) for milling herbs, nuts, coffee beans and purées.

key

 filler cap  lid  vents  goblet  sealing ring  blade unit  blade base  power unit  Power On indicator  speed + pulse control

TYPE BLM61 & BLP61 only

Programme buttons

 drinks  ice crush  rinse

Multi mill (if supplied)

 multi mill jar

grinding mill (if supplied)

 mill lid  grinding mill blade assembly

grating mill (if supplied)

 mill lid  grating mill blade assembly

to use your blender

1 Fit the sealing ring  into the blade

unit  - ensuring the seal is located

orrectly in the grooved area.

Leaking will occur if the seal is damaged or incorrectly

itted.

2 Clip the blade unit  into the base

.

3 Screw the blade assembly onto the

goblet – ensuring the blade assembly is fully tightened . Refer to the graphics on the underside of the blade unit as follows:

- unlocked position

- locked position 4 Put your ingredients into the goblet. 5 Fit the filler cap to the lid and push

down to secure.

6 Fit the lid by pushing down until

secure.

7 Place the blender onto the power

unit .

The appliance will not work if the blender is incorrectly fitted.

8 Plug in and the indicator light will

remain unlit whilst in the “O” OFF position. TYPE BLM60 & BLP60 - Turn the speed control to select a speed (refer to the recommended usage chart).

Select a speed between ‘Min’ to ‘Max’ by turning the speed control. At the end of blending return the speed control to “O” OFF before removing the blender.

Do not remove the goblet until the blades have stopped rotating and the speed control is in the “O” OFF position.

(P) Pulse – operates the motor in a start/stop action. The pulse will operate for as long as it is held in position.

Note: If the blender is removed from the power unit whilst a speed is selected the Indicator light will go out and the blender will stop. The blender willl restart immediately if refitted.

YPE BLM61 & BLP61 only -

Turn to the “on” position and the

ower On indicator  and the 3

re-programmed buttons will light

p up.

ote: In the “on” position the Power

n indicator will flash if the goblet is

O not fitted to the power unit.

n the “O” OFF position all the

ndicator lights will remain off.

9 Select a speed (refer to the

recommended usage chart). Choose one of the following options:

Select one of the 3 pre-programmed buttons. When the required programme button is pressed the light on the other button will go out. The blender will switch off automatically at the end of the preset time. If you wish to stop before the pre-set time, press the selected programme button again.

Select a speed between ‘Min’ to ‘Max’ by turning the speed control. At the end of blending return the speed control to “O” OFF before removing the blender.

Do not remove the goblet until the blades have stopped rotating and the speed control is in the “O” OFF position.

(P) Pulse – operates the motor in a start/stop action. The pulse will operate for as long as it is held in position.

Refer to the troubleshooting section if you experience any problems with the operation of the blender.

hints

To blend dry ingredients - cut into pieces, remove the filler cap, then with the machine running, drop the pieces down one by one. Keep your hand over the opening. For best results empty regularly.

The processing of spices is not recommended as they may damage the plastic parts.

hen making mayonnaise, put all

W the ingredients, except the oil, into

he blender. Remove the filler cap.

hen, with the appliance running,

T add the oil slowly through the hole in

he lid.

hick mixtures, e.g. pâtés and dips,

T may need scraping down. If the

ixture is difficult to process, add

ore liquid.

Recommended Usage Chart (Programme buttons)

rogramme Usage/Food Max. Programme

P Button Items Recommended Time

Cold Liquids Max 1.6 litres 60 secs

rinks & Cocktails

ilkshakes and milk Max 1.2 litres

M based drinks

moothies 1 litre Liquid

Drinks

Ice A change in speed will be crush noted - this is normal.

Rinse

Processing times stated are for guidance only and will vary depending on the exact recipe used, ingredients being processed and personal preference. Stop the processing when the desired result has been achieved.

Place the fresh fruit and liquid ingredients in first (includes yoghurt, milk and fruit juices). Then add ice or frozen ingredients (includes

frozen fruit, ice or ice cream)

Ice crushing- Automatic 10 ice cubes 45 secs Pulsing action (200g)

Freeze fruit juice in ice trays for Slushie type drinks

A change in speed will be Max 500 mls 30 secs noted - this is normal. warm water Use to rinse the goblet before taking apart for cleaning. For best results always take the blender apart for cleaning and dry thoroughly before re-assembling.

uantity

+ 16 hidden pages