Kenmore Elite 10657715701, 10657716700, 10657716701, 10657719700, 10657719701 Owner’s Manual

...
0 (0)
Side by Side Refrigerator
Refrigerador de dos puertas
R_frig_rateur c6te & c6te
F_s _/_.... _' ......,,_
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
2318589 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca
TABLEOF CONTENTS
WARRANTY ..................................................................................... 2
Proper Disposal of Your Old Refrigerator .................................... 3
Unpack the Refrigerator ............................................................... 4
Location Requirements ................................................................ 4
Electrical Requirements ................................................................ 5
Water Supply Requirements ........................................................ 5
Base Grille .................................................................................... 5
Refrigerator Doors ........................................................................ 6
Adjust the Doors ........................................................................... 7
Connect Water Supply ................................................................. 8
Prepare the Water System ........................................................... 9
Normal Sounds .......................................................................... 10
REFRIGERATOR USE ................................................................. 10
Ensuring Proper Air Circulation ................................................. 10
Using the Controls ..................................................................... 10
Water and Ice Dispensers ......................................................... 11
Water Filter Status Light ............................................................ 14
Water Filtration System ............................................................. 14
Ice Maker and Storage Bin ........................................................ 15
REFRIGERATOR FEATURES ..................................................... 16
Refrigerator Shelves .................................................................. 16
Dell Drawer ................................................................................ 16
Convertible Vegetable/Meat Drawer, Crisper and Covers ....... 16
Convertible Vegetable/Meat Drawer Temperature Control ...... 17
Crisper Humidity Control ........................................................... 17
Wine or Can/Bottle Rack ........................................................... 17
Utility Bin .................................................................................... 17
FREEZER FEATURES .................................................................. 18
Freezer Shelf.............................................................................. 18
Freezer Basket or Bin ................................................................ 18
DOOR FEATURES ....................................................................... 18
Tilt-out Freezer Door Bin ........................................................... 18
Chilled Door Bin ......................................................................... 18
Door Rails or Bins ...................................................................... 19
Door Bins ................................................................................... 19
Tilt-out Fruit Bin ......................................................................... 19
REFRIGERATOR CARE ............................................................... 20
Cleaning ..................................................................................... 20
Changing the Light Bulbs .......................................................... 20
Power Interruptions ................................................................... 21
Vacation and Moving Care ........................................................ 21
TROUBLESHOOTING .................................................................. 22
Refrigerator Operation ............................................................... 22
Temperature and Moisture ........................................................ 23
Ice and Water ............................................................................. 23
PROTECTION AGREEMENTS .................................................... 24
In the U.S.A ................................................................................ 24
In Canada ................................................................................... 25
ACCESSORI ES............................................................................. 25
WATER FILTER CERTIFICATIONS ............................................ 26
PRODUCT DATA SHEET ............................................................ 26
SERVICE NUMBERS ............................................... BACK COVER
KENMORE ELITE®APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.
If this appliance is used for other than private family purposes,
this warranty applies for only 90 days from the date of purchase.
FIVE-YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM
For five years from the date of purchase, when this refrigerator is operated and maintained according to the instructions supplied with it, Sears will repair the sealed system (consisting of refrigerant, connecting tubing, and compressor), free of charge, if defective in materials or workmanship.
THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP. SEARS WILL NOT PAY FOR:
1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed,
operated or maintained according to all instructions supplied with the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States and Canada.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co.
Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2B8
PRODUCT RECORD
In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product.
Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.
Model number
Serial number
Purchase date
Save these instructions and your sales receipt for future reference.
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
SAVE THESE INSTRUCTIONS
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker kit ready models only).
Use a sturdy glass when dispensing ice (on some models).
Proper Disposal of Your Old Refrigerator
Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous
- even ifthey will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
Take off the doors.
Leave the shelves in place so that children may not easily climb inside.
INSTALLATION INSTRUCTIONS
LJ a_s(.</< _,@ ¢ s_cst<._;;:s.,./
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
Ifthe ice storage bin is located on the door, remove the temporary shield from underneath the ice storage bin. See "Ice Maker and Storage Bin."
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.
NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C).
When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.
1/2" (1.25 cm)('
ii- i!
11
//
//j
t
2" (5.08cm)/
/
y
I
/
E ect ca H< su 'sments
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong. Do not use an adapter. Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an
extension cord. NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.
Water Pressure
A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):
Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refill after heavy usage.
If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."
If you have questions about your water pressure, call a licensed, qualified plumber.
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed
here.
TOOLS NEEDED:
Flat-blade screwdriver
7/16"and 1/2"Open-end or two adjustable wrenches
1/4"nut driver
NOTE: Your refrigerator dealer has a kit available with a 1/411 (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more easily.
IMPORTANT:
All installations must meet local plumbing code requirements.
Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.
1/411Drill bit
Hand drill or electric drill (properly grounded)
Remove the Base Grille:
1. Open both doors.
2. Place hands along the ends of the grille. Push in on the top of
the base grille and pull up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.
Replace the Base Grille:
1. Open both doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
Gathertherequiredtoolsandpartsandreadallinstructionsbeforestartinginstallation. TOOLSNEEDED:1/4",1A",and%6"hex-headsocketwrenches. IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEUnplugrefrigeratorordisconnectpower.Removefood,theice
storagebin,andanyadjustabledoororutilitybinsfromdoors. NOTE:Itmayonlybenecessarytoremoveeitherthedoorhandleorthedoorstogetyourproductthroughthedoorwayofyourhome.
Measurethedoorwaytoseewhetheryouneedtoremovetherefrigeratorhandlesorthedoors.
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
Wiring Connection
B
A. Wiring clip B, Wiring plugs
Water Dispenser
Tubing Connection
Top Left Hinge
A
Do Not Remove ScrewA
Door Removal
Handle Removal
(Optional On
Some Models)
Top Right Hinge
Do Not Remove Screw A
Bottom Hinge
A
A, Face of fitting
Remove the Handles (optional - on some models)
Replace the Doors and Hinges
1. Apply firm pressure on the handle to slide it up and off of the
shoulder screws. Do not push the handle toward the door; only apply pressure upward. See Graphic 1.
2. Move refrigerator into place. Replace handles as shown. See Graphic 1.
Remove the Doors
Electrical Shock Hazard
Disconnect power before removing doors. Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille. Place
hands along the ends of the grille. Push in on the top of the base grille and pull up on the bottom. See Graphic 2.
3. If you have a dispenser (ice or water), disconnect the water dispenser tubing located behind the base grille on the freezer door side. See Graphic 3.
Press blue outer ring against the face of fitting and pull
the dispenser tubing free. NOTE: Keep the water tubing connector attached to the
tube that runs underneath the refrigerator. The door can not be removed if the connector is still attached to the
tube that runs through the door hinge.
4. Disconnect the wiring located behind the base grille on the freezer door side. See Graphic 4.
Remove the wiring clip using a 1/4"hex-head socket
wrench.
Disconnect both wiring plugs.
5=
Close both doors and keep them closed until you are ready to lift them free from the cabinet.
6.
Use a s_6"hex-head socket wrench to remove the top left hinge screw and cover as shown. See Graphic 5.
7.
Remove remaining left hinge screws and hinge as shown. See Graphic 5.
IMPORTANT: Do not remove screw A.
8. Lift freezer door straight up off bottom hinge. See Graphic 6.
The water dispenser tubing and wiring remain attached to the freezer door and pull through the bottom left hinge. Be sure to protect the dispenser tubing and wiring from damage.
9. Remove top right hinge cover and screws as shown. See Graphic 7.
IMPORTANT: Do not remove screw A.
10. Lift the refrigerator door straight up off bottom hinge.
11. It may not be necessary to remove the bottom hinge to move the refrigerator through a doorway. Both bottom hinges have
similar construction.
If necessary, disassemble the hinges as shown. See
Graphic 8.
1. Replace both bottom hinges, if removed. Tighten screws.
2. Feed the water dispenser tubing and wiring through the bottom left hinge before replacing the freezer door on the hinge. You will need someone to assist you.
NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.
3. Align and replace the top left hinge as shown. See Graphic 5. Tighten screws.
4. Replace left hinge cover and screws.
5. Reconnect water dispenser tubing and wiring.
Push tubing into fitting until it stops and the black mark
touches the face of fitting. The tubing should be inserted approximately 3/4"(19.05 mm)into the fitting. See Graphic 3.
Reconnect wiring plugs. Locate the green electrical tape
on the wiring. Reinstall the wiring clip over the tape with the tabs pointing down. See Graphic 4.
6. Replace the refrigerator door by lifting the door onto the bottom right hinge.
7. Align and replace the top right hinge as shown. See Graphic 7. Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug into a grounded 3 prong outlet.
Door Closing t
1. Place a level inside the refrigerator at the back of the top shelf. See Graphic 9 in "Refrigerator Doors."
2. Locate the leveling screws behind the base grille of the refrigerator on either side.
3. Use a 1/2"hex-head socket wrench to adjust the rear roller leveling screws until the refrigerator is level. Turn the rear roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. See Graphic 10 in "Refrigerator Doors." Make sure refrigerator is level before proceeding.
4. Check the door alignment after leveling the refrigerator.
Align the Doors
IMPORTANT: First level the back of the refrigerator as described
in "Door Closing." The doors may be uneven after leveling the refrigerator. See
Graphic 11 in "Refrigerator Doors." The doors are preset at the factory so that the refrigerator door is higher than the freezer door by approximately the thickness of a quarter. Once the doors are loaded with food, they should be even. If the door height needs to be adjusted AFTER the doors have been loaded with food, follow these steps.
1. Use a 1/2"hex-head socket wrench to adjust the front roller leveling screws until the doors are even. Turn the front roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. See Graphic 12 in "Refrigerator Doors."
NOTE: Open and close both the refrigerator and freezer doors after each adjustment to check the door alignment.
2=
Open the doors and replace the base grille. Line up the grille support tabs with the metal clips. Push the grille firmly to snap it into place.
NOTE: Be sure to refasten the Tech Sheet behind the base grille.
Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line
is connected, turn the ice maker OFF.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a V2" (12.70 mm) to 11/4"(3.18 cm) vertical cold water pipe near the refrigerator.
IMPORTANT:
Make sure it is a cold water pipe.
Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use _/_" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5. Using a grounded drill, drill a _/4"(6.35 mm) hole inthe cold water pipe you have selected.
F D
A. Cold waterpipe E.Compression sleeve B. Pipe clamp F Shutoff valve C. Copper tubing G.Packing nut D. Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the _/_"(6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.
3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.
A. Tube clamp
B. Copper tubing
6=
The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the _A" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long enough, a _/4"x _/_"(6.35 mm x 6.35 mm) coupling is needed in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.
A B C
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb D. Coupling (purchased)
4=
Turn shutoff valve ON.
5.
Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.
C. Compression nut D. Valve inlet
D E F G
E.Ferrule (purchased)
Nut (purchased)
G. Household water line
Style 3
1. Unplug refrigerator or disconnect power.
2. Remove and discard the shipping tape and the black nylon plug from the gray, coiled water tubing on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
Please read before using the water system. Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. Flip the switch to the OFF setting. Style 1: The On/Off switch is located on the top left side of the freezer compartment, behind the ice maker cover door.
A
B
A.Bulb B.Nut (provided)
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See the "Water and Ice Dispensers" section.
NOTE: Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.
I@II
IO III
Style 2: The On/Off switch is located on the top right side of the freezer compartment.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain
filterable cysts.
2.
Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by
dispensing and discarding 1.5 gal. (5.4 L) of water. Cleaning the system will take approximately 3 minutes and will help clear air from the line. Additional flushing may be required in
some households. NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
3=
Open the freezer door and turn on the ice maker. Flip the switch to the ON position. Please refer to the "Ice Maker and Storage Bin" section for further instructions on the operation
of your ice maker.
Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced.
Depending on your model, you may want to select the maximum ice feature to increase the production of ice.
Yournewrefrigeratormaymakesoundsthatyouroldonedidn't make.Becausethesoundsarenewtoyou,youmightbe
concernedaboutthem.Mostofthenewsoundsarenormal.Hard surfaces,suchasthefloor,walls,andcabinets,canmakethe
soundsseemlouder.Thefollowingdescribesthekindsofsounds andwhatmaybemakingthem.
Ifyourrefrigeratorisequippedwithanicemaker,youwillhear abuzzingsoundwhenthewatervalveopenstofilltheice makerforeachcycle.
Yourrefrigeratorisdesignedtorunmoreefficientlytokeep yourfooditemsatthedesiredtemperaturesandtominimize energyusage.Thehighefficiencycompressorandfansmay causeyourrefrigeratortorunlongerthanyouroldone.You mayalsohearapulsatingorhigh-pitchedsoundfromthe compressororfansadjustingtooptimizeperformance.
Youmayheartheevaporatorfanmotorcirculatingairthrough therefrigeratorandfreezercompartments.Thefanspeed mayincreaseasyouopenthedoorsoraddwarmfood.
Rattlingnoisesmaycomefromtheflowofrefrigerant,the waterline,oritemsstoredontopoftherefrigerator.
Waterdrippingonthedefrostheaterduringadefrostcycle maycauseasizzlingsound.
Aseachcycleends,youmayhearagurglingsounddueto therefrigerantflowinginyourrefrigerator.
Contractionandexpansionoftheinsidewallsmaycausea poppingnoise.
Youmayhearairbeingforcedoverthecondenserbythe condenserfan.
Youmayhearwaterrunningintothedrainpanduringthe defrostcycle.
REFRIGERATOR USE
Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.
IMPORTANT:
The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature.
Wait 24 hours after you turn on the refrigerator before you put food into it. Ifyou add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a colder setting will not cool the compartments any faster.
If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.
The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
Digital Controls
For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure the controls are still preset as shown. The digital control panel is located at the top of the refrigerator compartment and enables you to view the temperature control set points.
NOTE: The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.
To turn refrigerator on and view set points:
Press and hold ON/OFF for 2 seconds.
In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator section through the top vent. On Style 2 models, this air is also evenly distributed throughout the refrigerator compartment through six vents on the back wall. Air then returns to the freezer
as shown.
Style 1 Style 2
,/
10
Cold Freezer _@ Refrigerator Col(_(_(_))
S_ & _ {O] }{[COMMENDED SETTING {31)
To view the Celsius temperatures:
Press the °C touch pad. The indicator will light up.
Colder Colder
o
NOTE: If the freezer temperature is below zero, the indicator light next to the freezer display will light up.
Adjusting Digital Controls To adjust set point temperatures:
Press the refrigerator or freezer up or down arrow until the desired temperature is reached.
Refrigerator Cold
@
(sT) @
NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures before other adjustments are
made.
Colder
The set point range for the freezer is -5°F to 5°F (-21 °C to
-15°C) and 33°F to 41 °F (1°C to 5°C) for the refrigerator.
CONDITION: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR
- Not set correctly for your conditions Control 1°higher REFRIGERATOR too warm REFRIGERATOR
- High use or room very warm Control 1°lower FREEZER too cold FREEZER Control
- Not set correctly for your conditions 1° higher FREEZER too warm/too little ice FREEZER Control
- High use or heavy ice use 1° lower
Accelerated Ice Production
The Accelerated Ice feature assists with temporary periods of heavy ice usage by increasing ice production over a 24-hour period.
Press the ACCELERICE 2touch pad to set the freezer temperature to -10°F (-23°C). The Accelerated Ice setting will remain on for 24 hours unless manually turned off. The display will continue to show your normal temperature set point.
If increased ice production is desired at all times, set the Freezer Control to a colder setting. Adjusting the freezer to a colder temperature may make some foods, such as ice cream, harder.
To reactivate the controls, press and hold the LOCK button for 2 seconds again.
NOTE: The lockout feature does not shut off power to the refrigerator or freezer. It simply deactivates the control panel buttons. The digital control panel display will remain lit and the buttons will beep when pressed, but no settings will be changed.
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the refrigerator or freezer door is open for 5 minutes. The alarm will repeat each minute until both doors are closed or Door Ajar Alarm is silenced or temporarily turned off.
When a door is opened, the Door Ajar Alarm feature is activated and the indicator lights up. The indicator light blinks when the
alarm sounds. NOTE: The Door Ajar Alarm feature turns off when both doors
have been closed. It resets and will re-activate when either door is opened again.
®
If alarm has not yet sounded and indicator light is on:
Press DOOR AJAR to temporarily turn the feature off. Press the button a second time to re-activate the feature.
If alarm is sounding and indicator light is blinking:
Press DOOR AJAR to silence the alarm. The indicator will stop blinking and remain on. Ifthe door remains open for
another 5 minutes, the alarm will sound again. Totemporarily turn the feature off, press DOOR AJAR a
second time before 5 minutes have passed. Once it is off, Door Ajar Alarm can be re-activated at any time by pressing
DOOR AJAR again.
SmartSense TM Temperature Management
The SmartSense TM feature assists with regulating the temperature inside the refrigerator. If a large quantity of warm food is placed in the refrigerator or warm air enters the refrigerator while the door is held open, SmartSense TM activates to quickly restore the temperature to the set point.
NOTE: SmartSense TM is always on when your refrigerator is operating. You do not need to press any buttons to activate it. The LED light on the control panel indicates that the feature is functioning properly.
Control Lockout
Control Lockout disables the control touch pads to allow easy cleaning and prevent unintentional control setting changes.
.@
s&g
To disable the controls, press and hold the LOCK button for 2 seconds.
Depending on your model, your water and ice dispensers may have one or more of the following features: a rotating water dispenser faucet and pull-out tray, a special light that turns on when you use the dispenser, a lock option to avoid unintentional dispensing, or an indicator that tells you when there has been a power outage.
NOTES:
The dispensing system will not operate when the freezer door is open.
After connecting the refrigerator to a water source, flush the water system by dispensing water into a sturdy container until you draw and discard 1.5 gal. (5.4 L) of water, or for approximately 3 minutes after the water begins dispensing. The flushing process cleans the water system and clears air from the lines. As the air is cleared from the lines, water may spurt out of the dispenser.
Allow 24 hours for the refrigerator to cool down and chill water.
Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.
11
The Water Dispenser
IMPORTANT: Dispense enough water every week to maintain a
fresh supply. To Dispense Water (Standard):
1. Press a sturdy glass against the water dispenser pad OR place the glass below the water dispenser and press the
WATER button.
3=
Press the up and down arrows to adjust the volume as desired.
NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL] per cup) are not the same size as a measuring cup (8 oz [237 mL]). You may need to adjust the volume to avoid unintentionally overfilling coffee cups.
4.
To dispense water, press a sturdy glass against the water dispenser pad OR place the glass below the water dispenser and press the WATER button.
0
NOTE: While dispensing water and for 5 seconds after dispensing has stopped, the digital display will show how much water has been dispensed. The default unit is ounces. To switch to cups or liters, press the UNITS button before dispensing.
2. Remove the glass OR release the button to stop dispensing.
To Dispense Water (Measured Fill}: Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons. NOTE: The exact amount of water you select will be dispensed.
Be sure that the container is empty and can hold the entire volume. If ice is in the container, you may need to adjust your
selection.
1. Press MEASURED FILL until the light turns on. Press MEASURED FILL again to turn the feature off.
Measured Fill
A. Measured fill B. Arrows
NOTE: The dispenser will automatically turn off Measured Fill after one minute of inactivity. When Measured Fill is turned off, any changes you have made will be lost and all defaults
will be restored.
2.
You can dispense water by the ounce, cup, or liter. The default unit is ounces. To switch to cups or liters, press the
UNITS button.
Units
NOTE: While dispensing water, the digital display will count down how much water remains to be dispensed, according
to the volume you selected. The flow of water will automatically stop once the desired volume has been
dispensed.
5=
To stop dispensing before the selected volume has been dispensed, remove the glass from the dispenser pad OR
press the WATER button a second time. NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how much water remains to be dispensed. The display will turn off
after one minute of inactivity. To select a new volume or select the same volume again, you
must first finish dispensing the selected volume, or turn the Measured Fill feature off and then turn it back on.
Rotating Faucet and Pull-out Tray (on some models)
Your dispenser may include a rotating water faucet and a small pull-out tray at the bottom of the dispenser.
A. Faucet rotated 90°
B. Pull-out tray
The faucet rotates up to 90° to allow for easy dispensing into large containers. To rotate it, push in and release the left-hand
side of the faucet as shown.
®
Default, minimum, and maximum volumes are listed below.
Units Default Minimum Maximum
Ounces 8 2 128
Cups 1 1/4 16 Liters 0.25 0.05 4
12
The faucet rotates 90° automatically. However, you must rotate it back into place manually. When in place, it will click.
NOTE: When using the dispenser with the faucet rotated, do not use the water dispenser pad. Only use the WATER button to dispense. Dispensing by pressing the container against the water dispenser pad may result in unintentional spilling.
The tray can be pulled out 11/2"(3.81 cm) to better support large containers. It is designed to catch small spills and allow for easy cleaning. There is no drain in the tray.
NOTE: The tray can be removed from the dispenser and carried to the sink to be emptied or cleaned. Pull the front of the tray out until it stops, then pull forward on the back of the tray and lift up on the front to remove it.
Thelce Dispenser
Ice dispenses from the ice maker storage bin in the freezer when the dispenser pad is pressed. The dispensing system will not operate when the freezer door is open. To turn off the ice maker, see "Ice Maker & Storage Bin."
Your ice maker can produce both crushed and cubed ice. Before dispensing ice, select which type of ice you prefer by pressing
the ICE button.
Crushed Cubed
For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.
To Dispense Ice:
1. If the ice storage bin is located on the door, remove the temporary shield from underneath the ice storage bin. See "Ice Maker and Storage Bin."
2. Press the button to select the desired type of ice.
Cut Hazard
Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.
The Dispenser Light (on some models)
When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may choose either
ON or AUTO.
On Auto
ON: Press LIGHT to turn the dispenser light on. AUTO: Press LIGHT a second time to select AUTO mode. The
dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the room darkens.
OFF: Press LIGHT a third time to turn the dispenser light off. The dispenser lights are LEDs that can not be changed. If it
appears that your dispenser lights are not working, be sure that the light sensor is not blocked (in AUTO mode). See "Troubleshooting" for more information.
The Dispenser Lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the product, to the ice maker, or to the dispenser light. It simply deactivates the ice and water dispensers. To turn off the ice maker, see "Ice Maker & Storage Bin."
Press and hold LOCKED for 3 seconds to lock the dispenser.
Press and hold LOCKED a second time to unlock the dispenser.
Locked
Power Outage Indicator (on some models)
NOTE: For additional information, see "Power Interruptions."
The power outage indicator lets you know if the power supply to your refrigerator is cut off for more than one hour. When power is restored, the indicator lights up and the dispenser's digital display reads "PF" (representing "power failure").
When the indicator is on, all other dispenser functions are disabled. To use the dispenser, you must reset the power outage
indicator.
Press and hold RESET for 3 seconds, until the feature beeps. For about 10 seconds, the display shows the number of hours (up to 48) that the refrigerator was without power.
PowerOutage
3=
Press a sturdy glass against the ice dispenser pad. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the pad in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.
4.
Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for up to 10 seconds
after removing the glass from the pad. The dispenser may continue to make noise for a few seconds after dispensing.
13
The water filter status light will help you know when to change your water filter. When the status light changes from green to yellow, this tells you that it is almost time to change the water filter. It is recommended that you replace the filter when the status light changes to red OR when water flow to your water dispenser or ice maker decreases noticeably. The filter should be replaced at least every 6 months. To change the filter, see "Changing the Water Filter" later in this section.
INDICATOR: STATUS: GOOD (green) New filter installed
ORDER (yellow) Order filter REPLACE (red) OR Replace water filter
when water flow decreases
After changing the water filter, reset the status light by pressing and holding the RESET button for 3 seconds. The status light will change from Replace (red) to Good (green) when the system is
reset.
Water Filter Status
2,
Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3,
Take the new cartridge out of its packaging and remove the protective cover from O-rings.
AB
A. Protective cover B. O-rings
4,
Place the cap (removed in Step 2) on the new filter. Align the ridge on the cap with the arrow on the filter. Turn the cap clockwise until it snaps into place.
._@.9 O _OOD
0 ORDER
REPLACE
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Changing the Water Filter
The water filter is located in the base grille below the freezer compartment door. It is not necessary to remove the base grille
to remove the filter.
1. Remove the filter by pressing the eject button and pulling straight out on the filter cap.
NOTES:
Avoid twisting the cap when removing the filter because
this could cause the cap to come off. If this occurs, replace the cap and pull the filter straight out.
There will be water in the filter. Some spilling may occur.
A
A. Eject button
B. Arrow on filter C. Ridge on cap
5. Push the new filter into the opening in the base grille. As the filter is inserted, the eject button will depress. The eject button will pop back out when the filter is fully engaged.
6. Pull gently on the cap to check that the filter is securely in place.
7. Flush the water system. See "Flushing the Water System After Changing Filter."
Flushing the Water System After Changing Filter
Use a sturdy container to depress the water dispenser lever until the water begins to flow. Flush the water system by dispensing and discarding 1.5 gal. (5.4 L)of water. Cleaning the system will take approximately 3 minutes and will help clear air from the line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of the dispenser.
14
........ B
A. Eject button
B.Filter cap
Using the Dispenser Without the Water Filter Cartridge
You can run the dispenser without a water filter cartridge. Your water will not be filtered.
1. Remove the filter by pressing the eject button and pulling on the cap. See "Changing the Water Filter" earlier in this
section.
2. Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3. With the cap in a horizontal position, insert the cap into the base grille until it stops.
4=
Turn the cap counterclockwise until the cap slips into the attachment slot. Then, turn the cap clockwise until it is in a horizontal position.
NOTE: The cap will not be even with the base grille.
Style 2:
The On/Off switch is located on the top right side of the freezer compartment.
1. Slide the control to the ON (left) position.
2. To manually turn the ice maker off, slide the control to the OFF (right) position.
Removing and Replacing the Storage Bin
Hold the base of the storage bin with both hands and press the release button to lift the storage bin up and out.
NOTE: It is not necessary to turn the ice maker control to the OFF position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed.
2. Replace the storage bin on the door and push down to make sure it is securely in place.
Turning the Ice Maker On/Off
NOTE: Your ice maker has an automatic shutoff. The ice maker sensor passes a beam from one freezer wall to the other,
automatically stopping ice production when the storage bin is full. The control will remain in the ON position.
Style 1: The On/Off switch is located on the top left side of the freezer
compartment, behind the ice maker cover door.
1. Flip the switch to the ON (top) position.
2. To manually turn the ice maker off, flip the switch to the OFF (bottom) position.
Io
Cleaning the Storage Bin
Empty the storage bin. Use warm water to melt the ice if necessary.
NOTE: Do not use anything sharp to break up the ice in the storage bin. This can cause damage to the storage bin and
the dispenser mechanism.
2. Wash the storage bin with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.
Remember
Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.
Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.
The quality of your ice will be only as good as the quality of the water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
It is normal for the ice cubes to be attached at the corners. They will break apart easily.
Do not store anything on top of the ice maker or in the storage bin.
15
REFRIGERATOR FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please
call the toll-free number on the back cover or in the "Accessories" section.
important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.
Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.
Slide-Out Shelves (on some models}
To Remove and Replace a Shelf in a Metal Frame:
1. Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.
2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.
Drop-Down Shelf (on some models)
To Remove and Replace the Drop-down Shelf:
1. Remove the drop-down shelf by sliding it up and back. Pull forward slightly to release the rear pegs from the track as
shown.
2,
With the rear pegs released, pull the shelf down and forward.
3.
Replace the shelf by sliding the front pegs into the track. Push the shelf up and back until the rear pegs drop into the track. Pull down and forward to be sure the shelf is securely in place.
The dell drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.
To Remove and Replace the Dell Drawer:
1. Remove the dell drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.
2. Replace the dell drawer by sliding it back past the stop.
Shelves and Shelf Frames
To Remove and Replace a Shelf/Frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.
16
Crisper and Convertible Vegetable/Meat Drawers
To Remove and Replace Drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of
drawer with the other hand and slide the drawer out the rest of the way.
2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.
CrisperorVegetable/MeatDrawerCovers
Meat Storage Guide
To Remove and Replace Covers:
1. Remove the crisper and meat drawer. Press up in center of
crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert
forward to remove.
2. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover.
3. Replace back of meat drawer cover frame into supports or slides on side walls of the refrigerator and lower or slide the front of the cover frame into place.
4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.
The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28° to 32°F (-2° to 0°C).
IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as
recommended.
Adjusting the Control
The convertible control comes preset at the lowest meat setting. To change a control setting: Move the control to the right
(colder) or to the left (less cold) as desired. To store vegetables: Set the control to VEG (all the way to the
left) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish ........................ use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days
Cold cuts, steaks/roasts .................................................. 3-5 days
Cured meats .................................................................. 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.
You can control the amount of humidity in the moisture-sealed crisper. Humidity Control is located on the crisper drawer. Adjust the control to any setting between LOW and HIGH.
LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bag or plastic container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.
To Remove and Replace the Wine Rack (left) or Can/Bottle
Rack (right):
1. Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.
IMPORTANT: Iffood starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.
NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.
17
FREEZER FEATURES
DOOR FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories" section.
{s!/mlx:,_ of s/'_s@es v;sd÷s by model i
To Remove and Replace the Shelf:
1. Lift the shelf up and off of the supports to remove it.
2. Replace the shelf by placing it in the supports. Check to be sure the shelf is securely in place.
Frozen Food Storage Guide
Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.
Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 Ibs of food per cubic foot [907 to
1,350 g per 28 L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.
For more information on preparing food for freezing, check a freezer guide or reliable cookbook.
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Accessories" section.
To Remove and Replace the Bin:
1. Remove the bin by pulling out on the tabs behind the basket to release it from the door liner.
2. Replace the bin by aligning the tabs with the buttons on the sides of the door liner. Firmly snap the tabs onto the buttons
as shown.
Cool air from the freezer is directed to the door bin directly beneath the vent.
NOTE: The dairy compartment and can rack are not chilled.
{p/asS, c bn o/s so'_e mode@
The freezer basket or bin can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves,
To Remove and Replace the Freezer Basket or Bin:
1. Remove the basket or bin by sliding it out to the stop.
2. Lift the front to slide the basket or bin out the rest of the way.
3. Replace the basket or bin by positioning it on the rails. Lift the basket or bin front slightly while pushing it in fully past the
stops.
18
Chilled Door Bin Control
The chilled door bin control is located on the left-hand side of the refrigerator compartment.
Turn the control clockwise (right) to reduce the flow of cold air to the bin and make it less cold.
Turn the control counterclockwise (left) to increase the flow of cold air to the bin and make it colder.
©®o Raso Bns
Thedoor railsor bins may be removed for easier cleaning.
Snap-On Door Rails or Bins
To Remove and Replace the Rails or Bins:
1. Remove the rails or bins by pushing in slightly on the front of
the bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail or bin.
2. Replace the rails or bins by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap
bracket onto the tabs above the shelf as shown.
To Remove and Replace the Bin:
1. Remove the bin by lifting it and pulling it straight out,
2. Replace the bin by sliding it in above the desired supports and pushing it down until it stops,
To Remove and Replace the Bin Parts:
1. Press either release button to open the tilt-out portion of the bin.
Drop-In Door Rails
To Remove and Replace the Rails:
1. Remove the rails by pulling straight up on each end of the rail,
2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.
D,< Bns
To Remove and Replace the Bins:
1. Remove the bin by lifting it and pulling it straight out.
2. Replace the bin by sliding it in above the desired supports
and pushing it down until it stops,
A
I
rT ,-d
A. Release buttons
2.
To remove the tilt-out portion of the bin, press m on the curved levers on each side of the bin. Pull up and out.
NOTES:
The bin can not be removed if it is tilted out all the way, Tilt it only part of the way before pressing the curved
levers to remove it,
Clean the parts as instructed in the "Cleaning" section,
A. Curved lever
3.
Reinstall the tilt-out portion of the bin. Be sure it is properly seated in the bottom of the bin before inserting the curved levers into position.
19
4. Replace the interior parts of the bin.
A. Strainer basket
B. Dividers C. Strainer mat
REFRIGERATOR CARE
Explosion Hazard
Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent odors from building up. Wipe up spills immediately.
To Clean Your Refrigerator:
1. Unplug refrigerator or disconnect power.
2. Remove all removable parts from inside, such as shelves, crispers, etc.
3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.
To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
4. Determine whether your refrigerator exterior is painted metal, Ultra Satin TM (stainless look) finish, brushed aluminum or stainless steel, and choose the appropriate cleaning method.
NOTE: Ultra Satin TM (stainless look) finish has a smooth, uniform color with a glossy finish that resists fingerprints. Stainless steel has a distinct grainy texture with variation in
color that is natural to steel.
Painted metal: Wash exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.
Brushed aluminum: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.
Ultra Satin TM (stainless look) finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.
Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.
To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel Cleaner & Polish. To order the cleaner, see "Accessories."
IMPORTANT: This cleaner is for stainless steel parts only?
Do not allow the Stainless Steel Cleaner & Polish to come into contact with any plastic parts such as the trim
pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft
cloth.
5=
There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille. See "Base Grille" graphic or "Base Grille" section.
Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area
of the condenser.
Replace the base grille when finished.
6=
Plug in refrigerator or reconnect power.
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size and shape. The lights require a 40-watt appliance bulb. Replacement bulbs are available from your deale£
f. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable as shown. NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size, shape and wattage.
4. Replace light shield when applicable as shown.
5. Plug in refrigerator or reconnect power.
2O
Refrigerator Control Panel Light
Reach behind the refrigerator control panel to remove and replace light bulb.
i ?
Crisper Light
If necessary, remove the top crisper drawer for easier access to the crisper light shield. Remove the light shield by lifting
the ends out of the brackets as shown. Replace the light shield by inserting the ends into the
brackets. If necessary, replace the top crisper drawer.
Upper Freezer Light
Remove the light shield by squeezing the sides of the light shield in toward the center while pulling the shield forward as
shown. Replace the light shield by fitting the tabs into the slotted
holes in the freezer liner. Push in the shield until it snaps into place.
If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold
and frozen. If the power will be out for more than 24 hours, do one of the
following:
Remove all frozen food and store it in a frozen food locker.
Place 2 Ibs (907 g) of dry ice inthe freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.
If neither a food locker nor dry ice is available, consume or can perishable food at once.
REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.
Vacations
If You Choose to Leave the Refrigerator On While You're
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker:
Raise wire shutoff arm to OFF (up) position or move the
switch to the OFF (right) setting.
Shut off water supply to the ice maker.
3. Empty the ice bin.
Lower Freezer Light Behind Top Freezer Basket (on some models)
Depending on your model, remove the top freezer basket or 3. top freezer basket shelf. Remove light shield by removing the
Phillips screw on the top of the shield. Carefully rotate the 4. shield until the left tab can be gently pulled from the freezer
wall. 5.
Replace the light shield by inserting the left tab into the freezer wall. Align top tab with screw hole and replace screw.
If You Choose to Turn the Refrigerator Off Before You Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
Turn off the water supply to the ice maker at least one day ahead of time.
When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
Depending on the model, turn the Temperature Control or Refrigerator Control to OFR See "Using the Controls."
Clean refrigerator, wipe it, and dry well. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and mold from building up.
Moving
When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
Turn off the water supply to the ice maker at least one day ahead of time.
Disconnect the water line from the back of the refrigerator.
When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.
2. Remove all food from the refrigerator and pack all frozen food in dry ice.
21
3. Empty the ice bin.
4. Depending on the model, turn the Temperature Control or Refrigerator Control to OFR See "Using the Controls."
5. Unplug refrigerator.
6. Empty water from the defrost pan.
7. Clean, wipe, and dry thoroughly.
8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.
TROUBLESHOOTING
Try the solutions suggested here first inorder to avoid the cost of an unnecessary service call.
9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See "Adjust the Doors."
10. Tape the doors closed and tape the power cord to the back of the refrigerator.
When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.
The refrigerator will not operate
Electrical Shock Hazard
Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter,
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power cord unplugged? Plug into a grounded 3 prong outlet.
Is outlet working? Plug in a lamp to see if the outlet is working.
Household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues,
call an electrician. Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls." New installation? Allow 24 hours following installation for
the refrigerator to cool completely. NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.
The refrigerator is noisy
Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with an explanation.
Buzzing - heard when the water valve opens to fill the ice maker
Pulsating - fans/compressor adjusting to optimize performance
Rattling - flow of refrigerant, water line, or from items placed on top of the refrigerator
Sizzling/Gurgling - water dripping on the heater during defrost cycle
Popping - contraction/expansion of inside walls, especially during initial cool-down
Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
The doors will not close completely
Door blocked open? Move food packages away from door.
Bin or shelf in the way? Push bin or shelf back in the correct position.
22
The doors are difficult to open
Explosion Hazard
Use nonflammable cleaner. Failure to de so can result in death, e×plosion, or fire.
Are the gaskets dirty or sticky? Clean gaskets with mild soap
and warm water.
The lights do not work
Is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."
Is the dispenser light set to ON? The dispenser light will operate only when the levers are pressed. If you want the dispenser light to stay on continuously, set the dispenser light to ON, or NIGHT LIGHT or AUTO. See "Water and Ice Dispensers."
Is the dispenser light set to NIGHT LIGHT or AUTO? Ifthe dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocked. See "Water and Ice Dispensers."
Temperature is too warm
New installation? Allow 24 hours following installation for the refrigerator to cool completely.
Door(s) opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully
closed.
Large load of food added? Allow several hours for refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See "Using the Controls."
There is intedor moisture buildup
NOTE: Some moisture buildup is normal.
Humid room? Contributes to moisture buildup.
Door(s) opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully closed.
The ice maker is not producing ice or not enough ice
Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.
Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice
production.
Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.
Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements" in either the Installation
Instruction booklet or the Use & Care Guide.
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
Water shutoff valve not fully open? Turn the water shutoff valve fully open.
Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.
Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."
Questions remain regarding water pressure? Call a licensed, qualified plumber.
Off-taste, odor or gray color in the ice
New plumbing connections? New plumbing connections can cause discolored or off-flavored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow 24 hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture proof packaging to store food.
Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.
Is there a water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration
system needs additional flushing.
23
The ice dispenser will not operate properly
Ifthe ice storage bin is located on the door, remove the temporary shield from underneath the ice storage bin. See "Ice Maker and Storage Bin."
Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close completely."
Ice bin installed correctly? Be sure the ice bin is firmly in position.
New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice
production.
Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute.
Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker.
Has the ice melted around the auger (metal spiral} in the
ice bin? Dump the ice cubes and clean the ice bin.
Cut Hazard
Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.
Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for "crushed" ice and begin dispensing again.
Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again.
The water dispenser will not operate properly
Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close
completely."
Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Is the water pressure at least 30 psi (207 kPa)? The water pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Kink in the home water source line? Straighten the water source line.
New installation? Flush and fill the water system.
Water filter installed on the refrigerator? The filter may be
clogged or incorrectly installed.
Is a reverse osmosis water filtration system connected to your cold water supply? See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.
Water is leaking from the dispenser
NOTE: One or two drops of water after dispensing is normal.
Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever.
New installation? Flush the water system. See "Water and Ice Dispensers."
Recently changed water filter? Flush the water system. See "Water and Ice Dispensers."
The dispenser water is not cool enough
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
New installation? Allow 24 hours after installation for the water supply to cool completely.
Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely.
Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.
Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
PROTECTION AGREEMENTS
Master Protection Agreements
Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.
Purchase a Master Protection Agreement now and protect
yourself from unexpected hassle and expense.
The Master Protection Agreement also helps extend the life of your new product. Here's what's included inthe Agreement:
v' Expert service by our 12,000 professional repair specialists v' Unlimited service and no charge for parts and labor on all
covered repairs
24
"No-lemon" guarantee - replacement of your covered product if four or more product failures occur within twelve
months
v' Product replacement if your covered product can't be fixed v' Annual Preventive Maintenance Check at your request - no
extra charge
v' Fast help by phone - phone support from a Sears technician
on products requiring in-home repair, plus convenient repair scheduling
v' Power surge protection against electrical damage due to
power fluctuations
v' Rental reimbursement if repair of your covered product takes
longer than promised
Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Master Protection Agreement today!
Some limitations and exclusions apply. For prices and
additional information, call 1-800-827-6655.
Sears Installation Service
For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the
U.S.A. call 1-800-4-MY-HOME ®.
ACCESSORIES
Replacement Parts:
To order stainless steel cleaner or replacement filters, call 1-800-4-MY-HOME ®and ask for the appropriate part number listed below or contact your authorized Kenmore dealer.
Stainless Steel Cleaner & Polish: Order Part #D22 M40083 R
Base Grille Water Filter:.
Replacement Filter:
Order Part #9030 (TIRFKB1) In Canada, Order Part #9030B (T1RFKB1)
WATER FILTER
CERTIFICATIONS
Maintenance Agreements Your purchase has added value because you can depend on
Sears HomeCentraP for service. With over 2,400 Service Technicians and more than a million parts and accessories, we
have the tools, parts, knowledge and skills to back our pledge: We Service What We Sell.
Your Kenmore ®product is designed, manufactured and tested to provide years of dependable operation. But like all products, it may require service from time to time. The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.
The Sears Maintenance Agreement
Is your way to buy tomorrow's service at today's price
Eliminates repair bills resulting from normal wear and tear
Provides phone support from a Sears technician on products requiring in-home repair
Even if you don't need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your product is in proper running condition.
Some limitations apply. For more information about Sears
Canada Maintenance Agreements, call 1-800-361-6665.
RaledServlceCapaci_): l(X) gal RatedServieeFIow: 05gpm
DO not us_ where water Israkrobiolo_lca]ly unsat_ or with water of anknown q uali_y, e_eept _hal
systems cer6fied _r cyst reduc_ien may b_, u_ed on dlsln f_x'ted water_ tha_ m_y ee_aln filterable cysts.
25
PRODUCT DATA SHEET
Base Grille Water Filtration System
Model TIKB1/TIRFKB1 Capacity 100 Gallons (379 Liters)
Taste and Odor, Particulate Class I_; and against NSF/ANSl Standard 53 for the reduction of Lead, Tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine
Mercury, Atrazine, Benzene, Toxaphene, O-Dichlorobenzene, Cysts, Turbidity, Asbestos, Lindane,
Tetrachloroethylene, Endrin, Alachlor, Chlorobenzene, Ethylbenzene, TTHM, MTBE and VOC.
This system has been tested according to NSF/ANSI 42/53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSl 42/53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average % Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 2.0 mg/L 2.0 mg/L _+10% 0.08 mg/L 2.0 mg/L 95.93 97.36 Particulate Class I* 85% reduction 3533333#/mL At east 10,000 part c es/mL 22000 #/mL** 11567 #/mL 99.38 99.67
Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average % Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction
Lead: @ pH 6.5 0.010 mg/L 150 ug/L 0.15 mg/L _+10% 1.0 ug/L 1 ug/L 99.33 99.33 Lead: @ pH 8.5 0.010 mg/L 157 ug/L 0.15 mg/L _+10% 2.0 ug/L 1.08 ug/L 98.72 99.31
Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.53 96.53 Mercury: @ pH 8.5 0.002 mg/L 0.0057 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.5 96.5
Benzene 0.005 mg/L 15 ug/L 0.015 mg/L _+10% 0.5 ug/L 0.5 ug/L 96.67 96.67 O-Dichlorobenzene 0.6 mg/L 1750 ug/L 1.8 _+10% 1.0 ug/L 1.0 ug/L 99.94 99.94
Toxaphene 0.003 mg/L 15 ug/L 0.015 _+10% 1.0 ug/L 1.0 ug/L 93.33 93.33 Atrazine 0.003 mg/L 10 ug/L 0.009 mg/L _+10% 2 ug/L 2 ug/L 80.8 80.8
Asbestos 99% 101 MFL 107to 108fibers/L tt 0.17 MFL 0.17 MFL 99.83 99.83 Live Cysts _ >99.95% 120,000/L 50,000/L min. 8/12 1/L _ 99.99 >99.99
Turbidity 0.5 NTU 11.4 NTU 11 _+1 NTU 0.41 NTU 0.24 NTU 96.4 97.89 Alachlor 0.002 mg/L 41.3 ug/L 0.04 _+10% 0.2 ug/L 0.2 ug/L 99.52 99.52 Endrin 0.002 mg/L 5.9 ug/L 0.006 _+10% 0.5 ug/L 0.3 ug/L 91.5 95.47 Ethylbenzene 0.7 mg/L 1867 ug/L 2.1 _+10% 0.70 ug/L 0.0588 ug/L 99.96 100
Lindane 0.002 mg/L 1.9 ug/L 0.002 _+10% 0.02 ug/L 0.02 ug/L 98.93 98.93 Chlorobenzene 0.6 mg/L 2.0 ug/L 2.0 _+10% 0.0005 ug/L 0.0005 ug/L 99.98 99.98 Tetrachloroethylene 0.005 mg/L 14.2 ug/L 0.015 _+10% 0.5 ug/L 0.5 ug/L 96.47 96.47 TTHM 0.080 mg/L 465 ug/L 0.45 _+20% 1.0 ug/L 0.5 ug/L 99.78 99.88
MTBE 0.005 mg/L 14 ug/L 0.015 _+20% 0.70 ug/L 0.52 ug/L 94.94 96.27 VOC 0.015 mg/L 0.3520 mg/L 0.300 _+10% 0.0060 mg/L 0.0008 mg/L 98.4 99.78
Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C).
It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to
perform as advertised.
Model T1KB1 : The filter monitor system measures the amount of water that passes through the filter and alerts you to replace the
filter. Style 1 - When the filter indicator reads 10%, order a new filter.
When the filter indicator reads 0%, it is recommended that you replace the filter.
Style 2 - When the filter indicator light changes from green to yellow, order a new filter. When the filter indicator light changes
from yellow to red, it is recommended that you replace the filter. Use replacement cartridge T1RFKB1, part #9030. In Canada, use
replacement cartridge T1RFKB1, part #9030B. 2006 suggested retail price of $41.99 U.S.A./S51.99 Canada. Prices are subject to
change without notice.
These contaminants are not necessarily in your water supply. While testing was performed under standard laboratory
conditions, actual performance may vary.
The product is for cold water use only.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the
*Class I particle size: >0.5 to <1 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
ttFibers greater than 10 um in length
_Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.
system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Refer to the front cover or "Accessories" section for the Manufacturer's name, address and telephone number.
Refer to the "Warranty" section for the Manufacturer's limited warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0,6 ° - 37.8°C) Service Flow Rate 0.5 gpm (1.9 L/min) @ 60 psi
26
Loading...
+ 58 hidden pages