E_ L
Counter Depth
Side by Side Refrigerator
...... _+,J_ _ ,+,_,_,
Refrigerador de dos puertas
con profundidad para armario
R_frig_rateur c6te _ c6te
profondeur de comptoir
Table of Contents / Indice / Table des mati_res ......... 2
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
2315477 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca
Table of Contents / Jndice/ Table des mati res
REFRIGERATOR SAFETY ............................... 2
REFRIGERATOR USE ..................................... 3
REFRIGERATOR CARE ................................... 6
TROUBLESHOOTING ...................................... 8
WATER FILTER CERTIFICATIONS .............. 10
PRODUCT DATA SHEET .............................. 11
PROTECTION AGREEMENTS ...................... 13
WARRANTY .................................................... 14
SERVICE NUMBERS ................. BACK COVER
SEGURIDAD DEL REFRIGERADOR ............ 15
USO DE SU REFRIGERADOR ...................... 16
CUIDADO DE SU REFRIGERADOR ............. 20
SOLUCION DE PROBLEMAS ....................... 21
HOJA DE DATOS DEL PRODUCTO ............ 24
CONTRATOS DE PROTECCION .................. 25
GARANT[A ...................................................... 26
NOMEROS
DE SERVICIO .................... CONTRAPORTADA
Product Record
In the space below, record your complete model number, serial Model number 106.
number, and purchase date. You can find this information on the
model and serial number label located on the inside wall of the
refrigerator compartment.
Serialnumber
Purchase date
Have this information available to help you obtain assistance or
service more quickly whenever you contact Sears concerning
your refrigerator.
Save these instructions and your sales receipt for future
reference.
Accessories
Replacement Parts
To order stainless steel cleaner or replacement filters, call
1-800-4-MY-HOME ®and ask for the appropriate part number
listed below or contact your authorized Kenmore dealer.
Stainless Steel Cleaner & Polish:
Order Part #D22 M40083 R
Base Grille Water Filter Cartridges:
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction may
be used on disinfected waters that may contain filterable
cysts.
Replacement Filter:
Order Part #9030 (1-1RFKB1)
In Canada, Order Part #9030B (1-1RFKB1)
SleCURITle DU RleFRIGleRATEUR ................ 27
UTILISATION DU RleFRIGleRATEUR ........... 28
ENTRETIEN DU RleFRIGleRATEUR ............. 32
DlePANNAGE .................................................. 33
FEUlLLE DE DONNleES SUR LE PRODUIT 36
CONTRATS DE PROTECTION ..................... 38
GARANTIE ...................................................... 39
NUMleROS
DE SERVICE ............. COUVERTURE ARRI#RE
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operating.
• Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
• Use two or more people to move and install refrigerator.
• Disconnect power before installing ice maker (on ice maker
kit ready models only).
• Use a sturdy glass when dispensing ice (on some models).
SAVE THESE INSTRUCTIONS
Proper Disposal ofYour Old Refrigerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
REFRIGERATOR USE
Before You Throw Away Your Old Refrigerator or Freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
For your convenience, your refrigerator controls are preset at the
factory. When you first install your refrigerator, make sure that the
controls are still at the set points as shown.
COLD FREEZER REFRIGERATOR COLD
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
NOTE: Make sure the refrigerator is plugged into a grounded
3 prong outlet.
COLDER COLDER
IMPORTANT:
• The refrigerator control adjusts the refrigerator compartment
temperature. The freezer control adjusts the freezer
compartment temperature.
• The displays normally show the actual temperature inside the
refrigerator and freezer. For information on displaying set
point temperatures, see "Viewing Set Points."
• Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a
lower (colder) setting will not cool the compartments any
faster.
Turning On Refrigerator
• If the refrigerator is not on, press ON/OFF to turn on the
cooling.
• To turn off your refrigerator, press ON/OFR Your refrigerator
will not cool when the control is set to Off.
NOTE: Pressing the On/Off button does not disconnect
power to the refrigerator. The interior lights will turn off if
either compartment door is open for more than 10 minutes.
Simply close and open the door to turn on the interior lights.
Viewing Set Points
The factory recommended set points (mid-settings) are 0°F
(-18°C) for the freezer and 37°F (3°C) for the refrigerator.
Set point range for the freezer: -6° to 6°F (-21 °C to -14°C)
Set point range for the refrigerator: 32 ° to 46°F (0°C to 8°C)
To view the set point temperatures, press either the up or down
arrow for the refrigerator or freezer temperature. The display will
become brighter to indicate that you are viewing the set points.
Five seconds after an adjustment is made, the display lights will
dim and return to the actual temperature.
NOTE: During automatic defrost cycles, the actual temperature
displayed may be higher than the set point. This is normal. The
actual temperatures should return to the set points within a few
hours following completion of the defrost cycle.
NOTE: While Grocery Savor TMis on, the display shows the
Grocery Savor TMtemperature set points. After 24 hours or when
Grocery Savor TMis manually turned off, the set points will return
to their previous setting.
Press GROCERY SAVOR to select this mode. Grocery Savor TM
will stay on for 24 hours or until it is manually turned off.
\_Lt
Accelerlce 2
Use Accelerlce _during periods of heavy ice usage.
• Press ACCELERICE _to select this mode. Accelerlce _will stay
on until it is manually turned off.
NOTE: Using Accelerlce _may make some foods in the
freezer, such as ice cream, harder.
• Press ACCELERICF a second time to deselect this mode.
NOTE: While using Accelerlce _,you may need to set the
convertible drawer temperature control to a higher (less cool)
setting. See "Convertible Drawer Temperature Control."
Adjusting Controls
The mid-settings indicated inthe previous section should be
correct for normal household refrigerator usage. The controls are
set correctly when milk or juice is as cold as you like and when
ice cream is firm.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not blocked.
If you need to adjust temperatures, use the settings listed in the
chart below as a guide. Wait at least 24 hours between
adjustments.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR
Control 1° lower
FREEZER too warm/too little ice FREEZER Control 1°
lower
REFRIGERATOR too cold REFRIGERATOR
Control 1° higher
FREEZER too cold FREEZER Control 1o
higher
Additional Control Panel Features
Temp Mode
• Press the °C button to select either Celsius or Fahrenheit
temperature displays.
Grocery Savor 'M
Use Grocery Savor TMto speed cooling when large grocery loads
are added. Grocery Savor TMsets the refrigerator temperature to
34°F (1°C) and the freezer temperature to -6°F (-21°C) for
24 hours.
The control can be adjusted to properly chill meats or vegetables.
The air inside the pan is cooled to prevent "spot" freezing and
can be set to keep meats at the National Livestock and Meat
Board recommended storage temperatures of 28° to 32°F (-2° to
0°C). The convertible drawer temperature control is preset to the
PRODUCE setting.
To Store Meat:
Set the control to one of the three MEAT settings to store meat at
its optimal storage temperature.
To Store Vegetables:
Set the control to PRODUCE to store vegetables at their optimal
storage temperatures.
NOTE: If food starts to freeze, move the control to the left (less
cold). Remember to wait 24 hours between adjustments.
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
NIGH (closed) for best storage of fresh, leafy vegetables.
©<:o C", Cont !o
The door chill control is located on the left-hand side of the
refrigerator compartment.
• Turn the control clockwise (right) to reduce the flow of cold air
to the door and make it less cold.
• Turn the control counterclockwise (left) to increase the flow of
cold air to the door and make it colder.
0
The Water Dispenser
IMPORTANT:
• The dispensing system will not operate when the freezer door
is open.
• After connecting the refrigerator to a water source, flush the
water system by dispensing water into a sturdy container
until you draw and discard 1.5 gal. (5.4 L) of water, or for
approximately 3 minutes after the water begins dispensing.
The flushing process cleans the water system and clears air
from the lines. As the air is cleared from the lines, water may
spurt out of the dispenser.
• Allow 24 hours for the refrigerator to cool down and chill
water.
• Dispense enough water every week to maintain a fresh
supply.
To Dispense Water:
1. Press a sturdy glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
The Dispenser Light
Style 1: The dispenser light can be turned on by pressing the ON
button.
Style 2: When you use the dispenser, the lever will automatically
turn the light on. If you want the light to be on continuously, you
may choose either ON or AUTO.
ON: Press the LIGHT button to turn the dispenser light on.
AUTO: Press the LIGHT button a second time to select AUTO.
The dispenser light will automatically adjust to become brighter
as the room brightens, dimmer as the room darkens.
OFF: Press the LIGHT button athird time to turn the dispenser
light off.
The dispenser lights are LEDs which should not need to be
changed. If it appears that your dispenser lights are not working,
check to be sure that the light sensor is not blocked (in AUTO
mode). See "Troubleshooting" for more information.
The Dispenser Lock (on some models)
The Ice Dispenser
The dispensing system will not operate when the freezer door is
open. Ice dispenses from the ice maker storage bin in the freezer
when the dispenser lever is pressed.
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, or a
lock option to avoid unintentional dispensing.
NOTE: Some models dispense both cubed and crushed ice.
Before dispensing ice, select which type of ice you prefer.
For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in size.
When changing from crush to cube, a few ounces of crushed ice
will be dispensed along with the first cubes.
To Dispense Ice:
1. Press the button to select the desired type of ice.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall
outside the glass.
IMPORTANT: You do not need to apply much pressure to the
lever in order to activate the ice dispenser. Pressing hard will
not make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
The dispenser can be locked for easy cleaning or to prevent
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates
the dispenser levers. The ice and water dispensers will not work.
• Press and hold the LOCK button until the red indicator
appears below LOCKED.
• Press and hold the LOCK button a second time to unlock the
dispenser.
Turning the Ice Maker On/Off
The On/Off switch is located on the top right-hand side of the
freezer compartment.
Toturn on the ice maker, slide the control to the ON (left) position.
To manually turn off the ice maker, slide the control to the OFF
(right) position.
NOTE: Your ice maker has an automatic shutoff. The ice maker
sensors will automatically stop ice production, but the control will
remain in the ON (left) position.
REMEMBER:
• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
• The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply cannot
be avoided, make sure the water softener is operating
properly and is well maintained.
• Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the
dispenser mechanism.
• Do not store anything on top of or in the ice maker or storage
bin.
Removing and Replacing Ice Storage Bin
Changing the Water Filter
1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out.
NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The
sensor cover ("flipper door") on the left wall of the freezer
stops the ice maker from producing ice if the door is open or
the storage bin is removed.
2. Replace the storage bin on the door and push down to make
sure it is securely in place.
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction may
be used on disinfected waters that may contain filterable
cysts.
Water Filter Status Display (on some models)
The filter status display will help you know when to change your
water filter. When the display reads 10%, order a new filter. It is
recommended that you replace the filter when the display reads
0% OR when water flow to your water dispenser or ice maker
decreases noticeably.
After changing the filter, reset the display by pressing the button.
The display will read 99% when the system is reset.
Non-indicator Water Filter (on some models)
If your refrigerator does not have the status light, you should
change the water filter every 6 months depending upon your
usage. If the water flow to the water dispenser or ice maker
decreases noticeably before 6 months have passed, replace the
water filter more often.
1. Press the eject button to release the filter from the base grille.
2. Pull the filter straight out.
3. Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4. Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water
will not be filtered. Simply insert the cap all of the way into the
base grille and rotate the cap until it is firmly in place.
5. Remove the protective covers from the O-rings. Be sure the
O-rings are still in place after the covers are removed.
6. Push the filter into the base grille. The eject button will pop
back out when the filter is fully engaged.
7. Flush the water system. See "Water and Ice Dispensers."
REFRIGERATOR CARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to prevent
odors from building up. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3.
Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water.
4.
There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
• Removethe base grille.
• Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
• Replace the base grille when finished.
5.
Plug in refrigerator or reconnect power.
If You Choose to Turn the Refrigerator Off Before You
Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
• Turn off the water supply to the ice maker at least one day
ahead of time.
• When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position or move the switch to the OFF
(right) setting.
3. Depending on the model, turn the Temperature Control or
Refrigerator Control to OFR See "Using the Control(s)."
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace
the bulb with one of the same size, shape and wattage. On some
models, the dispenser light requires a heavy duty 10-watt bulb.
All other lights require a 40-watt bulb. Replacement bulbs are
available from your dealer.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size,
shape and wattage.
4. Replace light shield when applicable.
5. Plug in refrigerator or reconnect power.
Vacations
If You Choose to Leave the Refrigerator On While You're
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker:
• Raise wire shutoff arm to OFF (up) position or move the
switch to the OFF (right) setting.
• Shut off water supply to the ice maker.
3. Empty the ice bin.
Moving
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
• Turn off the water supply to the ice maker at least one day
ahead of time.
• Disconnect the water line from the back of the
refrigerator.
• When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position or move the switch to the OFF
(right) setting.
2. Remove all food from the refrigerator and pack all frozen
food in dry ice.
3. Empty the ice bin.
4. Depending on the model, turn the Temperature Control or
Refrigerator Control to OFR See "Using the Control(s)."
5. Unplug refrigerator.
6. Empty water from the defrost pan.
7. Clean, wipe, and dry thoroughly.
8. Take out all removable parts, wrap them well, and tape them
together so they don't shift and rattle during the move.
9. Depending on the model, raise the front of the refrigerator so
it rolls more easily OR screw in the leveling legs so they don't
scrape the floor. See "Adjust the Doors."
10. Tape the doors closed and tape the power cord to the back
of the refrigerator.
When you get to your new home, put everything back and refer to
the "Installation Instructions" section for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
TROUBLESHOOTING
Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.
The refrigerator will not operate
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
• Power cord unplugged? Plug into a grounded 3 prong
outlet.
• Is outlet working? Plug in a lamp to see if the outlet is
working.
• Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
• Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls."
• New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting will
not cool either compartment more quickly.
The refrigerator is noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below
are listed some normal sounds with an explanation.
• Buzzing - heard when the water valve opens to fill the ice
maker
• Pulsating - fans/compressor adjusting to optimize
performance
• Rattling - flow of refrigerant, water line, or from items placed
on top of the refrigerator
• Sizzling/Gurgling - water dripping on the heater during
defrost cycle
• Popping - contraction/expansion of inside walls, especially
during initial cool-down
• Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan
• Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
The doors will not close completely
Check the following:
• Are food packages blocking the door open?
• Are all bins and shelves pushed back into the correct
positions?
The doors are difficult to open
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
• Are the gaskets dirty or sticky? Clean gaskets with mild
soap and warm water.
• Has the door been opened and closed within the last few
seconds? Wait at least 30 seconds to reopen the doors.
The ice cubes are hollow or small
Temperature is too warm
Check the following:
• Are the air vents blocked in either compartment?
• Are the door(s) opened often?
• Has a large amount of food just been added to the
refrigerator or freezer?
• Are the controls set correctly for the surrounding conditions?
There is interior moisture buildup
NOTE: Some moisture is normal.
• Are the air vents blocked in the refrigerator?
• Are the door(s) opened often?
• Is the room humid?
• Are the controls set correctly for the surrounding conditions?
• Was an automatic self-defrost cycle completed?
Items in meat pan/crisper are freezing
The temperature inside the meat pan/crisper may become too
cold, especially when using some additional control panel
features. Adjust the meat pan control to the closed setting.
The ice maker is not producing ice or not enough ice
This is an indication of low water pressure.
Check the following:
• Is the water shutoff valve fully open?
• Are there kinks in the water lines that could restrict water
flow?
• If you are using a water filter, remove the filter and operate the
dispenser. If water flow increases, the filter is clogged or
incorrectly installed.
• Is a reverse osmosis water filtration system connected to
your cold water supply? See "Water Supply Requirements" in
either the Installation Instructions or the Use & Care Guide.
• If you still have questions regarding your water pressure, call
a licensed, qualified plumber.
Off-taste, odor or gray color in the ice
Check the following:
• Are the plumbing connections new, causing discolored or off-
flavored ice?
• Have the ice cubes been stored too long?
• Does the freezer and ice bin need to be cleaned?
• Has food in the freezer or refrigerator been wrapped
properly?
• Does the water contain minerals (such as sulfur)? A filter may
need to be installed to remove the minerals.
• Is there a water filter installed on the refrigerator? Gray or
dark discoloration in ice indicates that the water filtration
system needs additional flushing.
• Is the ice maker wire shutoff arm or switch (depending on
models) in the OFF position?
• Is the water line shutoff valve to the refrigerator turned
on?
Has the ice maker just been installed? Is the freezer
temperature cold enough to produce ice? Wait 24 hours
after ice maker hookup for ice production to begin. Allow
3 days after ice production begins to completely fill ice
container.
Does the ice maker mold have water in it or has no ice
been produced? Make sure your refrigerator has been
connected to a water supply and the supply shutoff valve is
turned on.
• Has a large amount of ice just been removed? Allow
24 hours for ice maker to produce more ice.
• Is there a water filter installed on the refrigerator? The
filter may be clogged or installed incorrectly.
• Is an ice cube jammed in the ice maker ejector arm?
For models with an interior ice bin, remove the ice from the
ejector arm with a plastic utensil.
• Is a reverse osmosis water filtration system connected to
your cold water supply? See "Water Supply Requirements"
in either the Installation Instruction booklet or the Use & Care
Guide.
The ice dispenser will not operate properly
Check the following:
• Is the freezer door closed completely?
• Is the ice bin installed correctly?
• Is there ice in the bin?
• Has the ice frozen in the ice bin?
• Is ice stuck in the delivery chute?
• Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.
• Has the ice melted around the auger (metal spiral) in the
ice bin? Dump the ice cubes and clean the ice bin. See "Ice
Maker and Storage Bin."
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
• Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.
• Has the dispenser lever been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
WATER FILTER
CERTIFICATIONS
Slate of California
Deparhnent of Health Services
Water Treatment Device
Certificale Number
04 - 1605
Da_e issued Jam_ary 5,211_4
[)ate R_vised: I)ecCmt_r 14, ?00S
'Tr ad_.mark/#vlod*A I)e_i_n_ion
K_nmo_e Ad_an_d R_fil_rat,_ Filter r I KB 1 11RtKB t
K_nmol_ IlKBI 1IRt KB1
K_nmo,e blumat_ TI KB 1 r IRt KB 1
Kenmore U_mnal_ II T1KB I i 1RI_KB 1
Manufacturer: _ea_. R_buck a_ld Oumpany
• h_ _ater _r_tm_nt d_ie_(s) tisted e_ _his _,r tJficat _ haw m_t the t_ti_
116830 of the lIoalth and Sa_ (_od_ for _ _llowi_ h_lth rolat_d ro_t_
Microbiolo_ical ('_ami_an_ a_d Furbiditv ln_r_a_il
Replacement _lenlent(_
ir_mentspursuant to Sorfion
_llts:
_lo,_l Co_tamillant_
_nc
m_
The water dispenser will not operate properly
Check the following:
• Is the freezer door closed completely?
• Is the water shutoff valve not turned on, incorrectly installed
or clogged?
• Is the water line connected at the source?
• Is there a kink in the home water source line?
• Has the water system not filled? The water system needs
to be filled the first time it is used.
• Is the refrigerator connected to a cold water line with
water pressure of at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
• Is there a water filter installed on the refrigerator? The
filter may be clogged or incorrectly installed.
• Is a reverse osmosis water filtration system connected to
your cold water supply? See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.
Water is leaking from the dispenser
Check the following:
• Is the glass not being held under the dispenser long enough?
• Has the water system been flushed since installation or
changing filters?
2 45- IP (Sl_*ex'
rR_lomoa_'euc Aela
1,2.4- J r3ch/orobc,_llen_,
i 1 I-lrichloroelhen_
_°rrtchlor,,e_hanc
1_cn_oro_Ta_lene
Tr,_ah,m_thane_ _TItM_
[_ron_od_chlolon_e_hane
_'hlormonn
1,2-Diclllolopropane
cis-l,3-Dichloropropylene
Dino_eb
RatedServiceC_pnciiy: 100gaI RatedSer_,iceFIo_: 05gpm
Do _lot use _here water is mlcroblologlcally unsa ft_or with _ ater of unkllo_n qualil}, except that
systems cer tilled _r cyst reduction may be used on disinfected waters that may _ontaln filterable _ysts.
C]_lorodlbr_,m_melha_
Xylenr,
The dispenser water is not cool enough
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
• Has the refrigerator been newly installed or a large
amount of water recently dispensed? Allow 24 hours for
the refrigerator to cool completely.
• Has water not been recently dispensed? The first glass of
water may not be cool. Discard the first glass of water.
10
PRODUCT DATA SHEET
Base Grille Water Filtration System
Model TIKB1/TIRFKB1 Capacity 100 Gallons (379 Liters)
Taste and Odor, Particulate Class I_; and against NSF/ANSl Standard 53 for the reduction of Lead,
(_ Tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine
This system has been tested according to NSF/ANSl 42/53 for the reduction of the substances listed below. The concentration of the
indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water
leaving the system, as specified in NSF/ANSl 42/53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 2.0 mg/L 2.0 mg/L_+ 10% 0.08 mg/L ** 2.0 mg/L 95.93 97.36
Particulate Class I* 85% reduction 3533333#/mL At east 10,000 part c es/mL 22000 #/mL 11567 #/mL 99.38 99.67
Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction
Lead: @ pH 6.5 0.010 mg/L 150 ug/L 0.15 mg/L _+10% 1.0 ug/L 1 ug/L 99.33 99.33
Lead: @ pH 8.5 0.010 mg/L 157 ug/L 0.15 mg/L _+10% 2.0 ug/L 1.08 ug/L 98.72 99.31
Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.53 96.53
Mercury: @ pH 8.5 0.002 mg/L 0.0057 mg/L 0.006 mg/L _+10% 0.0002 mg/L 0.0002 mg/L 96.5 96.5
Benzene 0.005 mg/L 15 ug/L 0.015 mg/L _+10% 0.5 ug/L 0.5 ug/L 96.67 96.67
O-Dichlorobenzene 0.6 mg/L 1750 ug/L 1.8 _+10% 1.0 ug/L 1.0 ug/L 99.94 99.94
Toxaphene 0.003 mg/L 15 ug/L 0.015 _+10% 1.0 ug/L 1.0 ug/L 93.33 93.33
Atrazine 0.003 mg/L 10 ug/L 0.009 mg/L _+10% 2 ug/L 2 ug/L 80.8 80.8
Asbestos 99% 101 MFL 107to 10Sfibers/L tt 0.17 MFL 0.17 MFL 99.83 99.83
Live Cysts; >99.95% 120,000/L 50,000/L min. 8/L_ 1/W 99.99 >99.99
Turbidity 0.5 NTU 11.4 NTU 11 _+1 NTU 0.41 NTU 0.24 NTU 96.4 97.89
Alachlor 0.002 mg/L 41.3 ug/L 0.04 _+10% 0.2 ug/L 0.2 ug/L 99.52 99.52
Endrin 0.002 mg/L 5.9 ug/L 0.006 _+10% 0.5 ug/L 0.3 ug/L 91.5 95.47
Ethylbenzene 0.7 mg/L 1867 ug/L 2.1 _+10% 0.70 ug/L 0.0588 ug/L 99.96 100
Lindane 0.002 mg/L 1.9 ug/L 0.002 _+10% 0.02 ug/L 0.02 ug/L 98.93 98.93
Chlorobenzene 0.6 mg/L 2.0 ug/L 2.0 _+10% 0.0005 ug/L 0.0005 ug/L 99.98 99.98
Tetrachloroethylene 0.005 mg/L 14.2 ug/L 0.015 _+10% 0.5 ug/L 0.5 ug/L 96.47 96.47
]q-HM 0.080 mg/L 465 ug/L 0.45 _+20% 1.0 ug/L 0.5 ug/L 99.78 99.88
MTBE 0.005 mg/L 14 ug/L 0.015 _+20% 0.70 ug/L 0.52 ug/L 94.94 96.27
VOC 0.015 mg/L 0.3520 mg/L 0.300 _+10% 0.0060 mg/L 0.0008 mg/L 98.4 99.78
Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C).
• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
• Model T1KBI: The filter monitor system measures the amount of
water that passes through the filter and alerts you to replace the
filter.
Style 1 - When the filter indicator reads 10%, order a new filter.
When the filter indicator reads 0%, it is recommended that you
replace the filter.
Style 2 - When the filter indicator light changes from green to
yellow, order a new filter. When the filter indicator light changes
from yellow to red, it is recommended that you replace the filter.
Use replacement cartridge T1RFKB1, part #9030. In Canada, use
replacement cartridge T1 RFKB1, part #9030B. 2006 suggested
retail price of $41.99 U.S.A./S51.99 Canada. Prices are subject to
change without notice.
• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
• The product is for cold water use only.
Mercury, Atrazine, Benzene, Toxaphene, O-Dichlorobenzene, Cysts, Turbidity, Asbestos, Lindane,
Tetrach oroethy ene, Endr n, A ach or, Ch orobenzene, Ethy benzene, TTHM, MTBE and VOC.
• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
• Refer to the front cover or "Accessories" section for the
Manufacturer's name, address and telephone number.
• Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 L/min) @ 60 psi
*Class I particle size: >0.5 to <1 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
ttFibers greater than 10 um in length
_Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.
11
NSF/ANSI Standard 53 - Health Effects - Volatile Organic Chemicals (VOC's) included by surrogate testing*
Chemical Contaminant Influent Challenge NSF Maximum Permissible Chemical Reduction
Carbofuran 0.190 0.001 >99
Carbon tetrachloride 0.078 0.0018 98
Chloropicrin 0.015 0.0002 99
2,4, D 0.110 0.0017 98
Dibromochloropropane (DBCP) 0.052 0.00002 >99
p-Dichlorobenzene 0.040 0.001 >98
1,2-Dichloroethane 0.088 0.0048 95
1,1-Dichloroethylene 0.083 0.001 >99
Cis-1,2-Dichloroethylene 0.170 0.0005 >99
Trans-1,2-Dichloroethylene 0.086 0.001 >99
1,2-Dichloropropane 0.080 0.001 >99
Cis-1,3-Dichloropropylene 0.079 0.001 >99
Dinoseb 0.170 0.0002 99
Ethylene dibromide (EDB) 0.044 0.00002 >99
Haloacetonitriles (HAN):
Bromochloroacetonitrile 0.022 0.0005 98
Dibromoacetonitrile 0.024 0.0006 98
Dichloroacetonitrile 0.0096 0.0002 98
Trichloroacetonitrile 0.015 0.0003 98
Haloketones (HK):
1,1-Dichloro-2-Propanone 0.0072 0.0001 99
1,1,1-Trichloro-2-Propanone 0.0082 0.0003 96
Heptachlor (H-34, Heptox) 0.25 0.00001 >99
Heptachlor epoxide 0.0107 0.0002 98
Hexachlorobutadiene 0.044 0.001 >98
Hexachlorocyclopentadiene 0.060 0.000002 >99
Methoxychlor 0.05 0.0001 >99
Pentachlorophenol 0.096 0.001 >99
Simazine 0.120 0.004 >97
Styrene 0.150 0.0005 >99
1,1,2,2-Tetrachloroethane 0.081 0.001 >99
Toluene 0.078 0.001 >99
2,4,5 TP (Silvex) 0.270 0.0016 99
Tribromoacetic Acid 0.042 0.001 >98
1,2,4-Trichlorobenzene 0.160 0.0005 >99
1,1,1-Trichloroethane 0.084 0.0046 95
1,1,2-Trichloroethane 0.150 0.0005 >99
Trichloroethylene 0.180 0.0010 >99
Xylenes 0.070 0.001 >99
Concentration (rag/L) Level Concentration (rag/L) Percent (%)
*Chloroform was used as the surrogate chemical for VOC reduction claims
(6 NSF is a registered trademark of NSF International.
12