JVC UX-G60, UX-G55 User Manual

Download

MICRO COMPONENT SYSTEM

UX-G60 UX-G55

UX-G60

SUPER VIDEO

—Consists of CA-UXG60 and SP-UXG63

—Consists of CA-UXG55 and SP-UXG55

UX-G55

SUPER VIDEO

INSTRUCTIONS

GVT0169-006A

[US,UN,UB,UG,UX,A,UW]

Warnings, Cautions and Others

CAUTION— (Standby/on) button!

Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing the apparatus, ensure that the plug is easily accessible. The (Standby/on) button in any position does not disconnect the mains line.

• When the System is on standby, the STANDBY lamp lights red.

• When the System is turned on, the STANDBY lamp goes off. The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

CAUTION:

personnel.

CAUTION:

CAUTION

• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service

Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm

or more.

Front view Side view

15 cm

SP-UXG63 SP-UXG55

1 cm

CA-UXG60 CA-UXG55

15 cm

1 cm

SP-UXG63 SP-UXG55

15 cm

10 cm

[European Union only]

15 cm

CA-UXG60 CA-UXG55

15 cm

G-1

Introduction

Precautions

Installation

• Install the System in a location with adequate ventilation to prevent internal heat build-up in the System.

DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.

• Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C.

• Leave sufficient distance between the System and the TV.

• Keep the speakers away from the TV to avoid interference with the TV.

Power sources

• When unplugging the System from the wall outlet, always pull on the plug, not the AC power cord.

DO NOT handle the AC power cord with wet hands.

Moisture condensation

Moisture may condense on the lenses inside the System in the following cases:

• After starting to heat the room

• In a damp room

• If the System is brought directly from a cold to a warm place.

Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, then plug it in again.

Internal heat

• Make sure there is good ventilation around the unit. Poor ventilation could overheat and damage the unit.

DO NOT block the ventilation openings or holes. If they are blocked by a newspaper or cloth, etc., the heat may not be able to get out.

Others

• Should any metallic object or liquid fall into the System, unplug the AC power cord and consult your dealer before operating any further.

DO NOT disassemble the System since there are no user serviceable parts inside.

• If you are not going to operate the System for an extended period of time, unplug the AC power cord from the wall outlet.

If anything goes wrong, unplug the AC power cord and consult your dealer.

Contents

Introduction..............................................................1

Playable Disc/File Types .................................................... 2

How to Read This Manual .................................................. 2

Connections ..............................................................3

Display Indicators....................................................6

Daily Operations—Playback ..................................7

Daily Operations—Sound & Other Adjustments

Adjusting the Volume ....................................................... 12

Adjusting the Sound.......................................................... 12

Creating 3-dimensional Sound Field—3D Phonic............ 13

Presetting Automatic DVD Video Sound

Increase Level ............................................................... 13

Adjusting the Audio Input Level ...................................... 13

Changing the Display Brightness...................................... 14

Changing the Scanning Mode ........................................... 14

Changing the Picture Tone................................................ 14

Setting the Clock............................................................... 15

Turning Off the Power Automatically .............................. 15

Unique DVD/VCD Operations .............................16

Selecting the Audio Track................................................. 16

Selecting the Subtitle Language........................................ 17

Selecting the View Angle ................................................. 17

Selecting the Browsable Still Pictures .............................. 17

Playing Back Bonus Group............................................... 17

Making Dialogues Clear—Clear Voice ............................ 18

Special Effect Playback .................................................... 18

Advanced Playback Operations ...........................19

Programming the Playing Order—Program Play ............. 19

Playing at Random—Random Play .................................. 20

Playing Repeatedly ........................................................... 21

Prohibiting Disc Ejection—Child Lock............................ 21

On-screen Disc Operations ............................................... 22

Audio/Video File Operations ................................26

Advanced Tape Operations ..................................28

Recording on a Tape ......................................................... 28

Synchronized Recording ................................................... 29

Enjoying Karaoke..................................................30

Singing Along (Karaoke) .................................................. 30

Microphone Mixing .......................................................... 31

Reserving Karaoke Songs—Karaoke Program Play......... 32

Timer Operations...................................................33

Setup Menu Operations ........................................35

Additional Information .........................................37

Learning More about This System.................................... 37

Troubleshooting ................................................................ 41

Operating JVC’s TVs Using the Remote Control............. 43

Specifications .................................................................... 44

Parts Index ............................................................45

.....12

Playable Disc/File Types

DIGITAL VIDEO

• CD-R/-RW: Recorded in the Audio CD, Video CD, and SVCD formats. MP3, WMA*, JPEG, MPEG-1, MPEG-2, ASF* and DivX files written in accordance with the “ISO 9660” format can also be played.

• DVD-R/-RW, +R/+RW: Recorded in the DVD Video

format. MP3, WMA and DivX

files written in the UDF format can also be

, JPEG,

played.

• DVD-RW/-ROM: Recorded in the DVD Video Recording (VR) format.

• USB mass storage class device*: MP3, WMA, JPEG, MPEG-1, MPEG-2, ASF and DivX files.

In addition to the above discs/files, this System can playback audio data recorded on CD-Extra.

• The following discs cannot be played back: DVD-RAM, CD-I (CD-I Ready), CD-ROM, Photo CD, CD-G (CD-Graphics) and DVD/CD Text. Playing back these discs will generate noise and damage the speakers.

• In this manual, “file” and “track” are interchangeably used for MP3/WMA*/JPEG/MPEG-1/MPEG-2/ASF*/DivX operations.

• It is possible to playback finalized +R/+RW (DVD format only) discs. “DVD” lights on the front display panel when a +R/+RW disc is loaded.

• For UX-G55, the unit cannot playback DVD-VR discs with CPRM (Content Protection for Recordable Media).

About color system

This System accommodates the NTSC and PAL system and can playback discs recorded in either the NTSC or the PAL system.

• To change the color system, see page 14.

Note on Region Code

DVD players and DVDs have their own Region Code numbers. This System can playback only DVDs with an appropriate Region Code number.

• For details, see “Specifications” on page 44.

EX.:

COMPACT

SUPER VIDEO

DIGITAL AUDIO

MPEG-1, MPEG-2, ASF*

When playing a multi-channel encoded DVDs, the System properly converts these multi-channel signals into 2 channels, and emits the downmixed sound from the speakers.

To enjoy the powerful sound of these multi-channel

•

encoded DVDs,

connect a proper decoder or an amplifier with a proper built-in decoder to the OPTICAL DIGITAL OUT terminal on the rear.

IMPORTANT: Before playing a disc, make sure of the following...

• Turn on the TV and select an appropriate input mode on

the TV to view the pictures or on-screen displays.

• For disc playback, you can change the initial setting to

your preference. See “Setup Menu Operations” on page 35.

If “ ” appears on the TV screen when you press a button,

the disc cannot perform the operation you have

tried to do.

How to Read This Manual

• Button and control operations are explained in the table below.

•

Some related tips and notes are explained later in the sections “Learning More about This System” and “Troubleshooting,” but not in the same section explaining the operations ( indicates that the content has some information).

Indicates that you press the button

repeatedly

selected. Indicates that you press one of the buttons.

Indicates that you

sec.

for a specified period.

Indicates that you turn the control toward the specified direction(s).

Remote ONLY

Indicates that this operation is only possible using the remote control.

Indicates that this operation is only possible

Main Unit

ONLY

using the main unit.

INFO

briefly

briefly and

until an option you want is

press and hold

the button

(For Central and South American countries and Australia)

Audio formats

The System can playback the following digital audio formats.

LPCM

•

(Linear PCM)*,

DTS

(Digital Theater Systems),

DIGITAL

(Meridian Lossless

MLP

(Dolby Digital),

Packing)*

“DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of the Non-DVD side of a DualDisc in this product is not recommended.

For UX-G60 only

Connections

Do not connect the AC power cord until all other connections have been made.

• Connect VIDEO OUT directly to the video input of your TV. Connecting VIDEO OUT to a TV via a VCR may interfere with your viewing when playing back a copyprotected disc. Connecting VIDEO OUT to an integrated TV/VCR system may also interfere with your viewing.

Rear panel

The illustration below is UX-G60.

Supplied accessories

Check to be sure that you have all the following items.

• FM antenna (x1)

• AM loop antenna (x1)

• Composite video cord (x1)

• Remote control (x1)

• Batteries (x2)

• AC plug adapter (x1) (except for the Middle East, Hong Kong region and Australia)

If any item is missing, consult your dealer immediately.

~ From AM/FM antenna

See page 4.

Ÿ From the speakers

See page 4.

! From the powered subwoofer

See page 4.

VOLTAGE

SELECTOR

127V

110V

230V

-240V

220V

Front panel

The illustration below is UX-G60. Pull down the cover until you hear a clicking sound.

From the headphones

See page 7.

⁄ From the input of TV/monitor

See page 5.

Voltage selector (except for Hong Kong region and Australia)

See page 5.

@ From the digital input of digital

audio component

See page 5.

¤ To a wall outlet

Plug in the AC power cord only after all connections are completed.

• If the wall outlet does not match the AC plug, use the supplied AC plug adapter (except for the Middle East Hong Kong region and Australia

From the portable audio device

See page 5.

From the USB mass storage class device (for UX-G60 only)

See page 5.

AM/FM antenna

To assemble the AM loop antenna

To connect AM/FM antenna

AM loop antenna (supplied)

Speakers

• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).

Press and hold

ReleaseInsert

Red

FM antenna (supplied)

Extend it so that you can obtain the best reception.

For better AM/FM reception

AM loop antenna (supplied)

Keep it connected.

Vinyl-covered wire (not supplied)

Extend it horizontally.

FM outdoor antenna (not supplied)

From right speaker

To connect the powered subwoofer

From the powered

(not supplied)

The subwoofer connected can reproduce the bass sounds recorded in front left and right channels, but cannot reproduce the LFE signals in DVD multi-channel discs.

• Before plugging the unit to the main supply, make sure that the powered subwoofer is turned off.

CAUTION:

• DO NOT connect more than one speaker to each terminal.

• DO NOT push or pull the speakers as this will damage the foot spacers at the bottom of the speakers.

subwoofer

Black

SUBWOOFER

OUT

From left speaker

• Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 connector (IEC or DIN45325).

Ω

wire with coaxial type

⁄

TV/monitor

Connect the COMPONENT (for UX-G60 only), S-VIDEO, or VIDEO jacks which you want to use.

Red

• If an external device is not equipped with a stereo mini plug audio output, use a plug adaptor to convert the stereo mini plug to the corresponding plug of the audio output.

When connecting a USB mass storage class device (for UX-G60 only)

Blue

Green

Component video cord (not supplied)

• To select progressive scanning mode (see page 14), use COMPONENT jacks.

Composite video cord (supplied)

S-Video cord (not supplied)

• After connecting a TV, select the proper video signal mode according to the connection method. See “Changing the Scanning Mode” on page 14.

Digital audio component

Protective cap

USB cable

(not supplied)

At the front panel

• You can connect a USB mass storage class device such as a USB flash memory device, hard disk drive, multimedia card reader, etc. to this System. See pages 10 and 38 for details.

•

If you press USB MEMORY 3

, the System detects the USB mass storage class device and the control screen appears on the TV screen

. See page 26 for details.

Before plugging in the System (except for Hong Kong region and Australia)

Set the correct voltage for your area with the voltage selector on the rear.

VOLTAGE

SELECTOR

Use a screwdriver to set the voltage selector to the same voltage as where you are plugging in the unit.

110V

220V

(See also the back cover page.)

127V

230V

-240V

Preparing the remote control

• Set “DIGITAL AUDIO OUTPUT” in the “AUDIO” menu correctly according to the connected digital audio equipment (see page 36). If

the

setting is incorrect, loud

noise may be generated causing damage to the speakers.

When connecting a portable audio device (AUX)

Stereo mini plug

(not supplied)

At the front panel

• By using QP Link (Quick Portable Link), you can easily start playing back a portable audio device on this unit. See page 11 for details.

R6(SUM-3)/AA(15F)

• Dispose of batteries in the proper manner, according to federal, state, and local regulations.

DO NOT recharge, short, disassemble, heat the battery or dispose of it in a fire.

When using the remote control

Point the top of the remote control toward the remote sensor as directly as possible. If you operate it from a diagonal position, the operating range (approx. 5 m) may be shorter.

Display Indicators

The indications on the display tell you a lot of things while you are operating the System. Before operating the System, be familiar with when and how the indicator illuminates on the display.

QPLink S.TURBO PRGR.

MP3

SVCDVD

AHB PRO

B.S.P. BONUS

USB

ewrt yqp9uio;

QP Link (Quick Portable Link) indicator

• Lights when QP Link is activated.

Disc format indicators

• SVCD: lights when playing back an SVCD.

• VCD: lights when playing back a VCD.

• CD: lights when playing back a CD.

•DVD: lights when playing back a DVD.

Audio file format indicators

• MP3: lights when an MP3 track is detected.

• WMA

: lights when a WMA track is detected.

3D PHONIC indicator

• Lights when 3D Phonic is activated.

C.VOICE (Clear Voice) indicator

• Lights when Clear Voice is activated.

PG/PL indicators

• PG: lights when a DVD-VR formatted disc is called up.

• PL: lights when a Play List recorded on a DVD-VR formatted disc is called up.

Radio band indicators

• AM: lights when tuning in to an AM station.

• FM: lights when tuning in to an FM station.

FM reception indicators

• ST (stereo): lights while an FM stereo station with sufﬁcient signal strength is tuned in.

• MONO: lights while receiving an FM stereo station in monaural.

S.TURBO (Sound Turbo) indicator

• Lights when Sound Turbo II is activated.

PRGR. (Progressive) indicator*

• Lights when the progressive scanning mode is selected.

Main display

• While listening to radio: band (or preset number) and station frequency appear.

• While selecting “AUX”: “AUX” appears.

• While playing a disc or ﬁle: current status appears.

• While selecting “TAPE”: “TAPE” appears.

B.S.P. (Browsable Still Picture) indicator*

• Lights when playing a DVD Audio disc.

Browsable

Still Pictures are detected while

3DPHONIC

WMA

V.MASK C.VOICE

MIC

RND

PRGM

L-BANDIII

INFO

NEWS

AHB PRO indicator

• Lights when Active Hyper Bass Pro is activated.

BONUS indicator*

• Lights when detected

USB indicator*

• Lights when “USB MEMORY” is selected as the source.

Playback mode indicators

• PRGM: lights when Program Play is activated.

• RND: lights when Random Play is activated.

•

(repeat)1

–: lights when One Track/Chapter/Step Repeat is

activated.

–: lights when One Group/Title/All Tracks Repeat is

activated.

Indicators for Karaoke function*

• MIC: lights when the microphone is connected.

•V.MASK (Voice Mask): lights when Voice Mask is activated.

A.STBY (Auto Standby) indicator

• Lights when Auto Standby is activated.

• Flashes when disc playback stops with Auto Standby activated.

REC

indicator

• Lights while recording.

; 2 3

(tape – Lights to indicate the current tape running direction. – Flashes slowly during playback and recording. – Flashes quickly while rewinding a tape.

SLEEP

indicator

• Lights when the Sleep Timer is activated.

Daily Timer indicators

•: lights when Daily Timer is on standby or is being set.

• 1/2/3: lights when a Daily Timer (1, 2, or 3) is on standby; ﬂashes while working or being set.

• REC: lights when the Recording Timer stands by; ﬂashes while working or being set.

MONO

12 3

REC

SLEEP A.STBY

REC

a s

a DVD Audio disc with a bonus group is

direction) indicators

For UX-G60 only

Daily Operations

—Playback

Remote control

Number

buttons

RETURN

ENTER/SET TOP MENU/PG

1,¡

QP LINK

SHIFT

UX-G60

DVD/CD

USB

MEMORY

MENU/PL

,, ,

GROUP/TITLE

GROUP/TITLE SKIP 4,¢

FM/PLAY MODE

FM/AM

TAPE

/AUX

In this manual, operations using the remote control are mainly explained; however, you can use the buttons and controls on the main unit if they have the same (or similar) name and marks.

Turn on the power.

The STANDBY lamp on the main unit turns off.

• Without pressing AUDIO, the System turns on by pressing one of the source buttons.

• The System turns on and activates the AUX source by starting playback on an external device when QP Link is activated. (See page 11 for details.)

Select the source.

Playback automatically starts if the selected source is ready.

• If you press AUX, start playback on the external component.

Adjust the volume.

3 4

Operate the target source as explained later.

To turn off (standby) the unit

The STANDBY lamp on the main unit lights in red.

•A small amount of power is always consumed even while on standby.

UX-G55

TV VOL

AUDIO VOL

DVD/CD

QP Link

PRGR.

FM/AM

SVCDVD

AHB PROS.TURBO

B.S.P. BONUS

MP3

USB

TAPE

WMA

MIC

PRGM

L-BANDIII

3DPHONIC V.MASK C.VOICE

NEWS

RND

AUX

INFO

You can reduce power consumption by pressing DIMMER (while holding SHIFT) to turn the display off while on standby.

• When the display is turned off, QP Link does not work.

For private listening

Connect a pair of headphones to the PHONES jack on the main unit. The sound will no longer come out of the speakers.

connecting or putting on the headphones.

• Disconnecting the headphones will activate the

Be sure to turn down the volume before

speakers again.

DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound may damage your hearing, speakers and/or headphones when you turn on the System or start playback.

Listening to the Radio

To set the AM tuner interval spacing

INFO

Main Unit

ONLY

Before operating the tuner, it is required to select the appropriate AM space interval used for your area.

• This is possible only while the System is on standby.

Select the AM band.

UX-G60

FM/AM

/AUX

FM AM

AUX

UX-G55

FM/AM

Turn off the power.

FM AM

To select the band (FM or AM)

UX-G60

Remote control:

FM/AM

/AUX

Main unit:

UX-G55

Remote control: Main unit:

To tune in to a station

While FM or AM is selected...

Remote control: Main unit:

2 sec.

GROUP/TITLE SKIP

DOWN

FM/AM

/AUX

FM/AM

2 sec.

Select the appropriate AM space interval for your area.

DVD/CD

3/8

AM 9KHZ

(while holding...)

DISPLAY

(9 kHz interval)

AM 10KHZ

(10 kHz interval)

(while holding...)

Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency stops changing.

• When you repeatedly press the button, the frequency changes step by step.

To stop searching manually,

If the FM station has poor reception

FM/PLAY

MODE

press either button.

Remote ONLY

The MONO indicator lights on the display. Reception will improve though stereo effect is lost—Monaural reception.

To restore the stereo effect,

press the button again (the

MONO indicator disappears).

Remote

To preset the stations

ONLY

You can preset 30 FM and 15 AM stations.

Tune in to a station you want to preset.

• You can also store the monaural reception mode for FM preset stations if selected.

Activate the preset number entry mode.

ENTER/SET

QPLink S.TURBO PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

MP3

USB

WMA

MIC

PRGM

3DPHONIC

L-BANDIII

V.MASK C.VOICE

NEWS

RND

INFO

• Finish the following process while the indication on the display is flashing.

Select a preset number for the station you store.

Examples:

To select preset number 5, press 5.

To select preset number 10, press 10.

To select preset number 15, press 10, 1, then 5.

To select preset number 30, press 10, 3, then 0.

MONO

123

REC SLEEP A.STBY

REC

Playing Back a Tape

To insert a tape

You can playback type I tapes.

Push Insert Close

With the tape side facing outside

The illustration above is UX-G60.

To start:

To stop:

• You can also use the ¡

Store the station.

ENTER/SET

To tune in to a preset station

Select the band (FM or AM).

QPLink S.TURBO PRGR.

or 1

SVCDVD

AHB PRO

B.S.P. BONUS

button.

MP3

WMA

USB

PRGM

3DPHONIC V.MASK C.VOICE

MIC

RND

Remote

ONLY

L-BANDIII

NEWS

INFO

UX-G60

FM/AM

/AUX

AUX

UX-G55

Select the preset number for the station you stored.

Examples:

To select preset number 5, press 5.

To select preset number 10, press 10.

To select preset number 15, press 10, 1, then 5.

To select preset number 30, press 10, 3, then 0.

When “TAPE” is not selected as the

MONO

123

REC SLEEP A.STBY

REC

current source, press twice.

To rewind/fast-forward the tape:

Remote control:

GROUP/TITLE SKIP

Fast-forward the tape.

Rewind the tape.

Main unit:

DOWN

Rewind the tape.

Fast-forward the tape.

• You can also use the ¡

or 1

button.

Playing Back a Disc/File

INFO

Before operating a disc/file, be familiar how a disc/file is recorded.

• DVD Video comprises of “ “

Chapters

MPEG-2/ASF includes “ includes “ “

Tracks

,” DVD Audio

DivX comprises of “

,” JPEG comprises of “

Tracks

,” and CD/SVCD/VCD comprises of only

Files

.”

Titles

” which includes

/MP3/WMA*/MPEG-1/

Groups

” which

Groups

” which

• For playback of MP3/WMA*/JPEG/MPEG-1/MPEG-2/ ASF

/DivX files in a USB mass storage class device*, see

also page 26.

To insert a disc

You can insert a disc while playing another source.

• When using an 8 cm disc, place it on the inner circle of the disc tray.

To close the disc tray,

• If you press DVD/CD 3

press 0

again.

, disc tray closes automatically and playback starts (depending on how the disc is programmed internally).

To connect a USB mass storage class device

This section applies only to UX-G60.

You can connect a USB mass storage class device (see page 5) while playing another source.

• If you press USB MEMORY 3

, the System detects the USB mass storage class device, the control screen appears on the TV screen, and playback starts.

• To disconnect the USB mass storage class device safely, disconnect the device after turning the System off.

To playback a disc/file

To start:

DVD/CD USB

DVD/CD

•

While playing a disc/file:

USB

MEMORY

point, and when you start playback again by pressing DVD/CD 3

or USB MEMORY 3

standby), it starts from the position where you have stopped—Resume Play. (“RESUME” appears on the display when you stop playback.)

To stop completely while Resume is activated,

twice. (To cancel Resume, see “RESUME” on page 36.)

• When operating the System, the on-screen guide icon (see the following table) appears on the TV.

To pause: To stop:

To release, press DVD/CD 3 USB MEMORY 3

This System can store the stop

* (even while on

press 7

On-screen guide icons

• During DVD Video playback, the following icons may appear on the TV:

At the beginning of a scene containing multi-angle views.

At the beginning of a scene containing multi-audio sounds.

At the beginning of a scene containing multi-subtitles.

• The following icons will be also shown on the TV to indicate your current operation.

, , , , ,

• To deactivate the on-screen guide icons, see “ON SCREEN GUIDE” in “OTHERS” menu on page 36.

Remote

To select a title/group

ONLY

While playing a disc/file...

GROUP/TITLE SKIP

(while holding...)

• You can select a title/group directly by pressing a number button after pressing GROUP/TITLE (except for DVD-VR disc).

• Group name appears for MP3 or WMA* playback.

To select a chapter/track

• For VCD/SVCD, cancel PBC (see next page).

While playing a disc/file...

GROUP/TITLE SKIP

• First time you press 4

will go back to the beginning of the current chapter/track.

Remote

To locate a particular portion

ONLY

While playing a disc/file...

SLOW

x2 x5

x10 x20 x60

–

• Search speed changes as illustrated above except for MP3/ WMA*/DivX discs/files. For MP3/WMA*/DivX discs/ files, search speed and the indications on the TV are different.

• No sound comes out if searching is carried out while showing the moving picture.

To return to normal playback,

MEMORY 3

For UX-G60 only

* (depending on the source type).

press DVD/CD 3

, you

or USB

• For DivX, each time you press the > or < button, you can skip to a scene for 30 seconds or 5 minutes depending on the DivX file.

To move to the next or previous page of the current menu:

GROUP/TITLE SKIP

Moves to the next page. Moves to the previous page.

Remote

To locate an item directly

ONLY

You can select a title/chapter/track directly and start playback.

• For DVD Video, you can select

playback playback

, while you can select .

a title before starting

a chapter after starting

Examples:

To playback using the disc menu

For DVD Video/DVD Audio*:

Show the disc menu.

TOP MENU/PG MENU/PL

Select an item on the disc menu.

TV CH

To select number 5, press 5. To select number 10, press 10.

To select number 15, press 10, 1, then 5.

To select number 30, press 10, 3, then 0.

Remote ONLY

ENTER/SET

• With some discs, you can also select items by entering the number using the number buttons.

For SVCD/VCD with PBC:

While playing a disc with PBC, “PBC” appears on the display. When disc menu appears on the TV, select an item on the menu. Playback of the selected item starts.

Examples:

To select number 5, press 5. To select number 10, press 10.

To select number 15, press 10, 1, then 5.

To select number 30, press 10, 3, then 0.

To return to the previous menu:

RETURN

(while holding...)

press 7

To cancel PBC,

, then select a track. Playback starts

with the selected track.

To reactivate PBC,

“ON”), then press DVD/CD 3

press 7

(twice if Resume is turned

Playing Back a

Remote

Portable Audio Device

ONLY

By using QP Link (Quick Portable Link), you can easily start playing back a portable audio device connected to the AUX jack.

• Make sure to set the volume of your portable audio device loud enough so that the System can detect the sound signal.

To activate QP Link

AHB PRO

QP LINK

When QP Link is activated, connecting a portable device to the AUX jack and starting playback performs the following:

• While listening to another source... Changes the source to AUX automatically. (If you change from AUX to another source, QP Link will be canceled.)

• While the System is on standby... Turns on the System and activates the AUX source automatically (except when the display is turned off).

MP3

WMA

QPLink S.TURBO

PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

USB

MIC

PRGM

3DPHONIC

L-BANDIII

V.MASK C.VOICE

RND

NEWS

While QP Link plays back the device...

MP3

WMA

QPLink S.TURBO

PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

USB

MIC

PRGM

3DPHONIC

L-BANDIII

V.MASK C.VOICE

NEWS

RND

FM ST

INFO

SLEEP A.STBY

REC

INFO

SLEEP A.STBY

REC

QPL ON

(Initial setting)

QPL OFF

MONO

123

REC

Bubbles appear when QP Link works.

MONO

123

Bubbles disappear

REC

when the sound signal stops or is too weak.

INFO

For UX-G60 only

Daily Operations

AUDIO VOL

TV VOL

—Sound & Other Adjustments

Remote control

DIMMER

3D PHONIC

SCAN MODE

(UX-G60)

NTSC/PAL

(UX-G55)

CANCEL

ENTER/SET

AHB PRO

DVD/AUX LEVEL

SHIFT

SOUND TURBO

Main unit

SLEEP

A.STANDBY CLOCK/TIMER

VFP

DISPLAY

,, ,

BASS/TREBLE

AUDIO VOL +,–

FADE MUTING

Adjusting the Volume

You can adjust the volume level from VOL MIN to level 40 (VOL MAX).

Remote control:

To drop the volume in a moment

FADE

MUTING

To restore the volume,

adjust the volume level.

Adjusting the Sound

To reinforce the heavy sound

This boosts the low and high frequency sound—Sound Turbo II.

SOUND

TURBO

Main unit:

INFO

TURBO ON

VOLUME

Remote ONLY

press again, or

SOUND TURBO

3D-PHONIC

VOLUME +,–

The illustration above is UX-G60.

TURBOOFF

• When Sound Turbo II is turned on, AHB Pro is automatically turned on, and cannot be turned off. (AHB PRO indicator does not light even though the function is turned on.)

Remote

To reinforce the bass sound

ONLY

While Sound Turbo II is off, the richness and fullness of the bass sound is clearly maintained regardless of how you set the volume—Active Hyper Bass Pro.

AHB PRO

QP LINK

AHB ON

AHB OFF

(while holding...)

• When Sound Turbo II is turned on, AHB Pro setting cannot be changed.

Remote

To adjust the tone

ONLY

You can adjust the bass and treble level from –3 to +3.

To adjust the bass

BASS/

TREBLE

BASS

TREBLE

Canceled

TV VOL

AUDIO VOL

To adjust the treble

BASS/

TREBLE

BASS

TREBLE

Canceled

TV VOL

AUDIO VOL

Creating 3-dimensional Sound Field

Presetting Automatic DVD Video Sound

Remote

Increase Level

DVD Video sound is sometimes recorded at a lower level than other discs and sources. You can set the increase level for the currently loaded DVD Video, so you do not have to adjust the volume when you change the source.

• This only functions for DVD Video and DVD-VR format disc.

DVD/AUX

LEVEL

NORMAL

MIDDLE

HIGH

Original recording level.

Output level is increased (less than “HIGH”).

Output level is increased (more than “MIDDLE”). (initial setting)

ONLY

NORMAL MIDDLE

HIGH

—3D Phonic

• This does not function for MPEG-1/MPEG-2/ASF*/DivX discs.

While playing a disc...

Remote control:

(while holding...)

3D PHONIC

ACTION

Suitable for action movies and sports programs.

DRAMA

Creates natural and warm sound. Enjoy movies in a relaxed mood.

THEATER

Enjoy sound effects like in a major theater.

3D PHONIC

ACTION

OFF

3D PHONIC

Main unit:

DRAMA

THEATER

Remote

Adjusting the Audio Input Level

ONLY

If the sound from the component connected to the AUX jack is too loud or is too quiet when changing from another source to “AUX,” you can change the audio input level through the AUX jack (without changing the volume level).

While the “AUX” is selected as a source...

DVD/AUX

LEVEL

AUX LVL1 AUX LVL2

AUX LVL3

AUX LVL1

AUX LVL2

AUX LVL3

Select this when the sound is too loud with “AUX LVL2” selected. This setting is recommended for listening and recording when connecting an audio device other than a portable audio device to the AUX jack.

Select this when the sound is too loud with “AUX LVL3” selected.

Select this when listening to a portable audio device or recording the sound from it (initial setting).

For UX-G60 only

Changing the Display Brightness

Remote ONLY

Changing the Picture Tone

Remote ONLY

You can dim the display window.

DIMMER

DIM OFF

(Canceled)

DIM ON

AUTO DIM

(while holding...)

DIM ON AUTO DIM

*1 “AUTO DIM” does not work for CD/MP3/WMA*2.

Changing the Scanning Mode

Select the color system and the video signal mode according to the type of your TV. If you connect a progressive TV to UX-G60 through the COMPONENT jacks, you can enjoy a high quality picture from the built-in DVD player by selecting “PAL PRG” or “NTSC PRG.”

UX-G60

(while holding...)

UX-G55

Dims the display.

*1Removes the display illumination when

starting playback a disc with a video source.

• The display illuminates when playback stops.

Remote

SCAN MODE

ENTER/SET

ONLY

PAL PRGPAL

NTSC PRG

INFO

NTSC

• While showing a playback picture on the TV, you can select a preset picture tone, or adjust it and store your own taste.

To select a preset picture tone

While playing, display VFP setting screen.

VFP

(while holding...)

Select a preset picture tone.

NORMAL

GAMMA

BRIGHTNESS

CONTRAST

SATURATION

TINT

SHARPNESS

On the TV

NORMAL CINEMA

NORMAL

CINEMA

USER1/USER2

Normally select this.

Suitable for a movie source.

You can adjust parameters and can store the settings.

To remove the screen,

SHIFT.

USER2

press VFP again while holding

USER1

To adjust the picture tone

Select “USER1” or “USER2.”

• Follow steps 1 and 2 explained above.

Select a parameter you want to adjust.

TV CH

ENTER/SET

(while holding...)

PAL PAL PRG

NTSC NTSC PRG

NTSC/PAL

ENTER/SET

PAL

NTSC

Select for a conventional PAL TV.

Select for a progressive PAL TV.

Select to enjoy a progressive scanned picture with a progressive PAL TV.

Select for a conventional NTSC TV.

Select for a progressive NTSC TV.

Select to enjoy a progressive scanned picture with a progressive NTSC TV.

TV CH

GAMMA

BRIGHTNESS

CONTRAST

SATURATION

TINT

SHARPNESS

For UX-G60 only

Adjust if the neutral color is bright or dark (–3 to +3).

Adjust if the entire picture is bright or dark (–8 to +8).

Adjust if the far and near positions are unnatural (–7 to +7).

Adjust if the picture is whitish or blackish (–7 to +7).

Adjust if the human skin color is unnatural (–7 to +7).

Adjust if the picture is indistinct (–8 to +8).

Adjust the parameter.

TV CH

ENTER/SET

TV CH

Repeat steps 2 to 3 to adjust other parameters.

Turning Off the Power Automatically

Auto Standby

A.STANDBY

Canceled

Remote ONLY

To erase the screen,

Setting the Clock

press VFP again while holding SHIFT.

Remote ONLY

INFO

Without setting the built-in clock, you cannot use Daily Timers (see page 33) and Sleep Timer.

• To correct a mis-entry during the process, press CANCEL (while holding SHIFT) or CLOCK/TIMER (while holding SHIFT). You can return to the previous step.

Activate the clock setting mode.

MP31WMA

3DPHONIC

CLOCK/TIMER

VD PRO

BONUS

USB

MIC

PRGM

V.MASK C.V RND

(while holding...)

• If you have already adjusted the clock before, press the button repeatedly until the clock setting mode is selected.

Set the time.

• Adjust the hour, then the minute.

ENTER/SET

MP3

WMA

QPLink S.TURBO PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

USB

MIC

PRGM

3DPHONIC

L-BANDIII

V.MASK C.VOICE

NEWS

RND

MONO

123

INFO

REC SLEEP A.STBY

REC

Now the built-in clock starts working.

(while holding...)

When Auto Standby is in use, the A.STBY indicator lights on the display. When disc play stops, the A.STBY indicator starts flashing. If no operation is done for about 3 minutes while the indicator is flashing, the System turns off (standby) automatically.

Sleep Timer

You can set the shut-off time so that you can go to bed without turning it off yourself.

Specify the time (in minutes).

SLEEP

(while holding...)

10 20 30 60 90 120 150

Canceled

Wait until the set time disappears.

To check the time remaining until the shut-off time,

SLEEP while holding SHIFT.

• If you press the button repeatedly, you can change the shut-off time.

press

To check the current clock time during play

DISPLAY

Source information

Disc type

Clock

Unique DVD/VCD Operations

The following discs/files can be played back only with UX-G60:

• DVD Audio, WMA, ASF, DivX Ultra

• Files in a USB mass storage class device

Remote control

Number

buttons

C.VOICE

ZOOM

ANGLE

,, ,

ENTER /SET

DVD/CD 3

SLOW ,

AUDIO/MPX

PAGE SUBTITLE

SHIFT

(UX-G60) SUBTITLE (UX-G55)

Selecting the Audio Track

For DVD Video/DivX:

While playing back a chapter

ONLY

INFO

Remote

containing audio languages, you can select the language to listen to.

For DVD Audio*:

While playing back a track containing

audio channels, you can select the audio channel to listen to.

For DVD-VR and SVCD/VCD:

When playing back a track,

you can select the audio channel to play.

• You can also select the audio track using the on-screen bar (see page 22).

AUDIO/MPX

While playing a DVD Video...

Ex.:

3/3

JAPANESE

3/3

JAPANESE

ENGLISH

1/3

ENGLISH

1/3

2/3

FRENCH

2/3

FRENCH

While playing a DVD Audio*/DivX...

Ex.:

1/3

2/3

3/3

While playing a DVD-VR, or SVCD/VCD...

AUDIO/MPX

SVCD

ST1 ST2 L1

R2 L2 R1

DVD-VR/VCD

ST L R

ST1/ST2/STTo listen to normal stereo (2-channel)

playback.

L1/L2/L

R1/R2/R

To listen to the left audio channel.

To listen to the right audio channel.

• SVCD can have 4 audio channels. SVCD usually uses these 4 channels to record two 2-channel recordings (ST1/ ST2).

For UX-G60 only

Selecting the Subtitle Language

Remote ONLY

Selecting the View Angle

Remote ONLY

For DVD Video/DivX:

While playing back a chapter containing subtitles in different languages, you can select the subtitle language to display on the TV.

For DVD-VR:

While playing, you can turn the subtitles on

or off.

For SVCD:

While playing, you can select the subtitles even

if no subtitles are recorded on the disc.

• You can also select the subtitle language using the

on-screen bar (see page 22).

While playing a DVD Video

/DivX

...

1/3

SUBTITLE

1/3

ENGLISH

TV CH

Ex.:

1/3 2/3

ENGLISH FRENCH JAPANESE

1/3

2/3

FRENCH JAPANESEENGLISH

While playing a DVD-VR...

3/3

JAPANESE

3/3

For DVD Video only:

While playing back a chapter containing multi-view angles, you can view the same scene from different angles.

• You can also select the multi-view angles using the on-

screen bar (see page 22).

While playing...

ANGLE

(while holding...)

Ex.:

1/3

2/3

Selecting the Browsable Still Pictures

This function is available only for UX-G60.

For DVD Audio only:

browsable still pictures (B.S.P.), you can select the still picture (turn the page) to be shown on the TV screen.

• If a track is linked to browsable still pictures (B.S.P.), they

are usually shown automatically during playback.

• You can also select the page using the on-screen bar (see

page 22).

(while holding...)

While playing back a track linked to

PAG E

SUBTITLE

3/3

Remote ONLY

Each time you press the button (while holding SHIFT), the still picture changes one after another (if available).

SUBTITLE

While playing an SVCD...

SUBTITLE

OFF

Remote

Playing Back Bonus Group

ONLY

This function is available only for UX-G60.

For DVD Audio only:

Some DVD Audio discs have a special group called “bonus group” whose contents are not open to the public.

• To playback a bonus group, you have to enter the specific

“key number” (a kind of password) for the bonus group. The way of getting the key number depends on the disc.

Select the bonus group.

• The bonus group is usually recorded as the last group (for example, if a disc contains 4 groups including a bonus group, “group 4” is the bonus group).

• For how to select the group, see “To select a title/group” on page 10.

Continued on the next page

For UX-G60 only

Enter the key number.

Follow the interactive instructions shown on the

ENTER/SET

screen.

To cancel the key number entry,

press 7

Slow-motion playback

• This does not function for MPEG-1/MPEG-2/ASF*1/DivX discs.

While playing...

Still picture playback starts.

Select slow motion speed.

Forward slow motion starts.

SLOW

1/32 1/16 1/8 1/4 1/2

–

Remote

Making Dialogues Clear—Clear Voice

ONLY

When you playback a disc, you can make the singer’s voices or dialogues of the movie clear—Clear Voice. When Clear Voice is in use, the C.VOICE indicator lights on the display.

• This function only works for center-channel encoded multi-channel disc.

C.VOICE

Off

(while holding...)

Remote

Special Effect Playback

ONLY

INFO

Pause playback

To pause:

While playing...

To resume normal playback:

DVD/CD

Frame-by-frame playback

While playing...

Still picture playback starts.

Reverse slow motion*2 starts.

1/32 1/16 1/8 1/4 1/2

*2 Only available for DVD Video.

To resume normal playback,

press DVD/CD 3

To replay the previous scenes (One-Touch Replay)

• This function is only used while playing DVD Video/ DVD-VR.

While playing back...

The playback position moves back about 10 seconds before the current position (only within the same title).

Zoom

While playing back...

ZOOM

(while holding...)

Move the zoomed-in position.

ZOOM 1

TV CH

ZOOM 2 ZOOM 3 ZOOM 4

ZOOM OFF

ZOOM 6 ZOOM 5

Advance the still picture frame by frame.

To resume normal playback,

press DVD/CD 3

TV CH

To cancel Zoom,

repeatedly until “ZOOM OFF” appears on the TV.

For UX-G60 only

press ZOOM (while holding SHIFT)

Advanced Playback Operations

Remote ONLY

INFO

The following discs/files can be played back only with UX-G60:

• DVD Audio, WMA, ASF, DivX Ultra

• Files in a USB mass storage class device

Remote control

Number

buttons

ZOOM

TOP MENU/PG

USB

MEMORY 3

DVD/CD 3

FM/PLAY

MODE

CANCEL

MENU/PL

,, ,

ENTER/SET ON SCREEN

4,¢

REPEAT A-B

REPEAT

SHIFT

Programming the Playing Order —Program Play

You can arrange the playing order of the chapters or tracks (up to 99) before you start playback.

• Program play cannot be used for DVD-VR/JPEG/ MPEG-1/MPEG-2/ASF*/DivX and files in a USB mass storage class device*.

• Resume does not work for Program Play.

Before starting playback, activate Program Play.

FM/PLAY

MODE

PROGRAM RANDOM

Canceled

MP3

WMA

QPLink

SVCDVD

AHB PRO

S.TURBO PRGR.

B.S.P. BONUS

PROGRAM

USE NUMERIC KEYS TO PROGRAM TRACKS. USE CANCEL TO DELETE THE PROGRAM.

3DPHONIC V.MASK C.VOICE

USB

MIC

RND

PRGM

On the display

No Group/Title Track/Chapter

2 3 4 5 6 7 8 9

L-BANDIII

NEWS

INFO

FM ST

SLEEP A.STBY

REC

MONO

123

REC

Main unit

DVD/CD #/

MEMORY #/

USB

, 7,

The illustration above is UX-G60.

On the TV

Select chapters or tracks you want for Program Play.

• For DVD Video/DVD Audio*/MP3/WMA*:

Select a title or group number.

Select a chapter or track number.

Repeat the above steps 1

and 2

• For SVCD/VCD/CD:

Select tracks.

To enter the numbers directly:

Examples:

To enter number 5, press 5. To enter number 10, press 10.

To enter number 15, press 10, 1, then 5.

To enter number 30, press 10, 3, then 10.

Continued on the next page

For UX-G60 only

Start playback.

DVD/CD

Playback starts in the order you have programmed.

Remote

Playing at Random—Random Play

ONLY

You can play all chapters or tracks at random.

• Random Play cannot be used for DVD-VR/JPEG/ MPEG-1/MPEG-2/ASF*1/DivX, some DVDs and files in the USB mass storage class device*1.

To skip a step:

GROUP/TITLE SKIP

To pause: To stop:

To release, press DVD/CD 3

To check the programmed contents

Before or after playback...

TV CH

In the reverse order.

TV CH

In the programmed order.

• You can also use 4

or ¢

to check the programmed

contents.

To modify the program

Before or after playback...

To erase the last track/file:

CANCEL

Before starting playback, activate Random Play.

FM/PLAY

MODE

PROGRAM RANDOM

Canceled

MP3

WMA

QPLink S.TURBO PRGR.

Start playback.

DVD/CD

To skip a chapter/ track:

SVCDVD

AHB PRO

B.S.P. BONUS

USB

PRGM

3DPHONIC V.MASK C.VOICE

MIC

RND

L-BANDIII

NEWS

MONO

123

INFO

REC SLEEP A.STBY

REC

Playback starts in random order. Random Play ends when the entire disc has been played.

To pause: To stop:

To release, press DVD/CD 3

(while holding...)

To erase the entire program: To add another track/

file to the program:

2 sec.

CANCEL

Repeat step 2.

(while holding...)

To exit from Program Play

Before or after playback...

FM/PLAY

MODE

PROGRAM RANDOM

Canceled

To exit from Random Play

Before or after playback...

FM/PLAY

MODE

For UX-G60 only

PROGRAM RANDOM

Canceled

Playing Repeatedly

A-

A-B

ONLY

INFO

Remote

• You can also select the repeat mode using the on-screen bar (see pages 23 and 24).

• For MP3/WMA*1/JPEG/MPEG-1/MPEG-2/ASF*1/DivX, see page 27.

Repeat Play

You can repeat playback.

• For DVD Video:

While playing...

REPEAT A-B

REPEAT

• For DVD Audio

REP CHAP REP TTL

While playing or before playback...

REPEAT A-B

REPEAT

REP TRK REP GRP

• For CD/SVCD/VCD:

While playing (without PBC for SVCD/VCD) or before playback...

REPEAT A-B

REPEAT

REP TRK

• For DVD-VR:

While playing an original program...

REPEAT A-B

REPEAT

REP CHAP REP PG

REP OFF

(Canceled)

While playing a Program List...

REPEAT A-B

REPEAT

REP CHAP REP PL

REP OFF

(Canceled)

REP OFF

(Canceled)

REP OFF

(Canceled)

REP ALL

REP OFF

(Canceled)

REP ALL

*2 During Program Play and Random Play, “REP STEP”

appears instead of these indications, and repeat modes change as follows for all the discs.

REP STEP REP ALL

REP OFF

(Canceled)

A-B Repeat

You can repeat playback of a desired portion by specifying the beginning (point A) and the ending (point B).

• A-B Repeat cannot be used for MP3/WMA*1/MPEG-1/ MPEG-2/ASF* mass storage class device*1.

While playing (without PBC for SVCD/VCD), select

the start point (A).

(while holding...)

Select the end point (B).

(while holding...)

To cancel A-B Repeat, press REPEAT A-B again while

holding SHIFT.

• A-B Repeat will also be canceled when you stop play or skip the chapter or track.

Prohibiting Disc Ejection—Child Lock

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible only while the System is on standby.

/DivX, some DVDs and files in the USB

starts flashing on the

REPEAT A-B

REPEAT

display.

• appears on the TV if the TV is turned on.

stops flashing.

REPEAT A-B

REPEAT

• appears on the TV.

• You can search for the end point using the ¡ button.

Main Unit

ONLY

REP CHAP

REP TTL

REP TRK

REP GRP

REP PG

REP ALL

REP PL

*2Repeats the current chapter.

Repeats the current title.

*2Repeats the current track.

Repeats the current group.

Repeats the current program.

Repeats the disc or program.

Repeats the current Program List.

While the disc tray is closed...

QPLink

SVCDVD

AHB PRO

S.TURBO PRGR.

B.S.P. BONUS

(while holding...)

To cancel the prohibition,

repeat the same procedure.

“UNLOCKED” appears on the display.

For UX-G60 only

MP3

USB

WMA

MIC

PRGM

3DPHONIC

L-BANDIII

V.MASK C.VOICE

RND

NEWS

MONO

123

INFO

REC SLEEP A.STBY

REC

Remote

TITLE

CHAP

GROUP 1

TOTAL

1:25:58

TIME

OFF

CHAP.

TRACK

1/3

PAGE 1 / 5

On-screen Disc Operations

ONLY

You can check the disc information and use some functions through the on-screen bar.

On-screen bars

DVD Video

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/ 3 1/1

Dolby D 3/2.1ch

OFF

TITLE 2

TITLE

CHAP 3

CHAP

1/3

1/3 1/3

DVD Audio

DVD-AUDIO

TIME

LPCM 2/0.0ch

OFF

TRACK

GROUP 14

TRACK 23

1/ 3

PAGE

1/ 3

INFO

TIME 0:00:58

TOTAL

1:25:58

TIME 0:00:58

On-screen Bar Information

Disc type

Playback information

Indication Meanings

Dolby D, LPCM Audio format 3/2.1ch, 2/0.0 ch Channel number

TRACK

Operation modes

Indication Meanings

/ Forward/Reverse search

/ Forward/Reverse slow-motion

SVCD

TIME

OFF

TIME OFF ST1

1/3

TITLE

1/3

-/ 4

TRACK 3

CHAP

TIME 0:00:58

TOTAL

1/3 1/3

1:25:58

Function icons (on the pull-down menu)

Indication Meanings

VCD

TIME

OFF

TIME OFF ST

TITLE

1/3

TRACK 3

CHAP

TIME 0:00:58

TOTAL

1/3 1/3

1:25:58

TIME

OFF

TIME OFF

TITLE

1/3

TRACK 3

CHAP

TIME 0:00:58

TOTAL

1/3 1/3

1:25:58

MP3/WMA

/MPEG-1/MPEG-2/ASF*1/DivX

Current title

Current chapter

Current group

Current track

Time indications

Playback

Pause

Stop

Select to change the time indication.

Select to repeat playback.

Select for time search.

Select for chapter search.

Select for track search.

Select to change the audio language or channel (see also page 16).

Select to change subtitle language (see also page 17).

Select to change the view angle (see also page 17).

Select to change the page (see also page 17).

FILE

USB*

USB

213

TIME 00:00:58

TOTAL

CHAP

1:25:58

213

TIME 00:00:58

TOTAL

CHAP

1:25:58

For UX-G60 only

To operate using the On-screen Bar

TIME

Ex.: Selecting a subtitle (French) for DVD Video

While a disc is selected as the source...

Display the entire on-screen bar.

ON SCREEN

*2 This does not appear for MP3/WMA*1/JPEG/MPEG-1/

MPEG-2/ASF*1/DivX discs and files in a USB mass storage class device*1.

Select (highlight) the item you want.

Dolby D

DVD-VIDEO

3/2.1ch

Dolby D

DVD-VIDEO

3/2.1ch

TIME

OFF

TIME OFF CHAP. 1/31/31/1

TITLE

TITLE 2

1/3

CHAP 3

CHAP

TIME 0:00:58

TOTAL

1/3 1/3

disappears

1:25:58

For detailed operations of the following functions, see also “To operate using the On-screen Bar” on the left.

To change the time information

You can change the time information in the on-screen bar and the display window on the main unit.

While playing, display the on-screen bar with the pull-down menu.

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

Make sure is selected (highlighted).

Change the time indication.

ENTER/SET

Dolby D 3/2.1ch

OFF

TITLE

TIME 0:00:58

TITLE 2

1/3

CHAP 3

CHAP

1/3 1/3

REM 0:11:23

TOTAL 1:01:58T. REM 0:35:24

TIME 0:00:58

TOTAL

1:25:58

OFF

TV CH

ENTER/SET

Dolby D 3/2.1ch

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

Display the pop-up window.

ENTER/SET

Select the desired option in the pop-up window.

Finish the setting.

TITLE 2

CHAP

TITLE

1/3

CHAP 3

TITLE 2

CHAP

1/3

1/31/31/1

CHAP 3

TITLE 2

CHAP

ITLE

1/3

1/32/31/1

Pop-up window disappears.

CHAP 3

1/3 1/3

TOTAL 1:01:58

TOTAL

1/3 1/3

ENGLISH

TOTAL 1:01:58

TOTAL

1/3 1/3

FRENCH

TIME 0:00:58

TOTAL

To remove the on-screen bar

ON SCREEN

1:25:58

TIME

Elapsed playing time of the current chapter/track (except for DVD-VR).

REM

Remaining time of the current chapter/ track (except for DVD-VR).

TOTAL

T. REM

Elapsed disc time.

Remaining disc time.

To remove the on-screen bar

ON SCREEN

Repeat Play

• See also page 21.

While playing a disc (without PBC for SVCD/VCD), display the entire on-screen bar.

• Repeat Play can be selected before starting playback, except for DVD Video/DVD-VR.

Select .

2 3

Display the pop-up window.

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

OFF

Dolby D 3/2.1ch

OFF

TITLE 2

TITLE

TOTAL 1:01:58

CHAP 3

TOTAL

1/3 1/3

1:25:58

CHAP

1/3

For UX-G60 only

Continued on the next page

ENTER/SET

Select the repeat mode you want.

A-B

TITLE

GROUP

ALL

Repeats a desired portion (see below).

Repeats the current title.

Repeats the current group.

Repeats the disc (except for DVD) or program.

CHAPTER

TRACK

OFF

*2Repeats the current chapter.

*2Repeats the current track.

Cancels Repeat Play.

*1 While playing a DVD-VR disc, “PG” appears, and

while playing a Play list, “PL” appears.

During Program Play and Random Play, “STEP”

appears.

Finish the setting.

ENTER/SET

A-B Repeat

• See also page 21.

While playing, display the entire on-screen bar.

Select .

Display the pop-up window.

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

Select “A-B.”

TV CH

OFF

Dolby D 3/2.1ch

OFF

TITLE 2

TITLE

1/3

DVD-VIDEO

TIME

TIME OFF CHAP.

CHAP

OFF

TOTAL

1/3 1/3

Dolby D 3/2.1ch

A–B

TOTAL 1:01:58

CHAP 3

1:25:58

Time Search

You can move to a particular point by specifying the elapsed playing time from the beginning.

While playing (without PBC for SVCD/VCD), display the entire on-screen bar.

• Time Search can be used before starting playback, except for DVD Video/DVD-VR.

Select .

Display the pop-up window.

OFF

Dolby D 3/2.1ch

TIME _ : _ _ : _ _

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

Enter the time.

TITLE 2

TITLE

CHAP

1/3

You can specify the time in hours/minutes/seconds.

Examples:

To move to a point of 1 (hours): 02 (minutes): 00

(seconds), press 1, 0, 2, 0, then

To move to a point of 54

(minutes): 00 (seconds), press 0, 5, 4, 0, then 0.

• It is always required to enter the hour digit (even “0” hour), but it is not required to enter trailing zeros (the last two digits in the examples above).

•

To correct a mis-entry, press cursor < to erase the last

entry.

Finish the setting.

The System starts playing the disc from the selected playing time.

CHAP 3

1/3 1/3

TIME 0:00:58

TOTAL

1:25:58

Select the start point (A).

ENTER/SET

Select the end point (B).

ENTER/SET

A-B Repeat starts. The selected portion plays repeatedly.

• Before pressing ENTER/SET, you

To cancel A-B Repeat,

in step 4.

DVD-VIDEO

TIME

TIME A- CHAP. 1/3

Dolby D 3/2.1ch

TITLE 2

TITLE

1/3

can search for the end point using the ¡

button.

repeat steps 1 to 3, and select “OFF”

Chapter/Track Search

You can search for the chapter (DVD Video/DVD-VR) or track (DVD Audio*

While playing, display the entire on-screen bar.

2 3

CHAP.

Select

Display the pop-up window.

DVD-VIDEO

TIME

TIME OFF CHAP. 1/31/31/1

For UX-G60 only

) number to play.

Dolby D 3/2.1ch

TRACK

TITLE 2

TITLE

CHAPTER _

1/3

CHAP 3

CHAP

TOTAL 1:01:58

TOTAL

1/3 1/3

1:25:58

Enter the desired chapter/track number.

Examples:

To select chapter/track 5, press

To select chapter/track 10, press 1, then 0.

To select chapter/track 15, press 1, then 5. To select chapter/track 30,

press 3, then 0.

•

To correct a mis-entry, press the number buttons until

the desired number shown in the pop-up window.

Finish the setting.

ENTER/SET

The System starts playing the searched chapter or track.

Browsable Still Pictures

This function is available only for UX-G60.

For DVD Audio only:

browsable still pictures (B.S.P.), you can select the still picture (turn the page) to be shown on the TV.

• If a track is linked to browsable still pictures (B.S.P.), they are usually shown automatically during playback.

While playing a DVD Audio, display the entire

on-screen bar.

Select .

PAGE 1 / 5

Display the pop-up window.

TV CH

OFF

LPCM 2/0.0ch

DVD-AUDIO

TIME

Select a still picture you want.

Finish the setting.

ENTER/SET

While playing back a track linked to

TIME 0:00:58

P 14

1/3

TRACK 23

1/3

TRACK 23

PAGE

3/5

PAGE

1/5

TIME 0:00:58

GROUP 14

TRACK

Control screen for DVD-R/-RW in DVD-VR format

The control screen is superimposed on the TV screen when you call up Program List (PG) or Play List (PL).

To select playback type

To select the Program List:

TOP MENU/PG

To remove the list, press the same button again.

Ex.: When Program List is selected.

ORIGINAL PROGRAM

No Date Ch Time Title

1 03/12/06 12:15L 2 09/12/06 23:05 3 18/12/06 08:17 4 20/12/06 07:47 5 25/12/06 19:38 Mr. Lawrence 6 28/12/06 14:20

12 3 4 5 6

Ex.: When Play List is selected.

PLAY LIST

No Date Chap Length Title

1 03/12/06 002 0:23:24 Nebula G. 2 15/12/06 004 1:04:39 3 24/12/06 013 0:41:26 4 27/12/06 017 0:09:08

Listed number

Recording date

Recording channels

Recording time

Title

Highlight bar (current selection)

Chapters included

Playback time

To select an item in the list and start playback

TV CH

To select the Play List:

MENU/PL

L L L L L

La fleur The last struggle free flyer BOOM!

Satisfy U

CDJ Secret Garden S. Walker

67812

ENTER/SET

TV CH

Audio/Video File Operations

The following discs/files can be played back only with UX-G60:

• DVD Audio, WMA, ASF, DivX Ultra

• Files in a USB mass storage class device

Remote control

ZOOM

,, ,

USB MEMORY 3

DVD/CD 3

REPEAT A-B REPEAT

ENTER/SET

GROUP/TITLE

GROUP/TITLE SKIP

4,¢

SHIFT

Operations on the

Control

Remote

ONLY

INFO

Screen

You can search for and play the desired items through the control screen for MP3/WMA*/JPEG/MPEG-1/MPEG-2/ ASF*/DivX files.

Control screen for MP3/WMA*/JPEG/MPEG-1/ MPEG-2/ASF

The control screen automatically appears on the TV screen when you load a disc or connect and select a USB mass storage class device* in which MP3, WMA*, JPEG, MPEG-1, MPEG-2, ASF*, or DivX is recorded.

/DivX files

Ex.: When the MP3 disc is loaded.

6 7

Group : 2 / 3

Spring

Summer

Fall Winter

Tr ack Information

Title Rain Artist

Album

TIME : 00:00:14REPEAT TRACK

Tr ack : 6 / 14 (Total 41)

Cloudy.mp3 Fair.mp3 Fog.mp3 Hail.mp3 Indian summer.mp3

Rain.mp3

Shower.mp3 Snow.mp3 Thunder.mp3 Typhoon.mp3 Wind.mp3 Winter sky.mp3

8 9

Current group number/total group number

Current group

Group list

Track information (ID3 Tag Version 1.0: only for MP3 and WMA*)

Current track

Repeat Play setting

Elapsed playing time of the current track (except for JPEG)

Operation mode icon

Current track number/total number of tracks in the current group (total number of tracks on the loaded disc)

Highlight bar

Track list

• If files of different types (MP3, WMA*, JPEG, MPEG-1, MPEG-2, ASF* and DivX) are recorded on a disc or device, select the file type to play (see page 35).

To move the highlight bar between group list and track list

Moves the bar to the track list.

Moves the bar to the group list.

To select an item in the list

TV CH

Move the highlight bar to the desired item.

• If you move the highlight bar

TV CH

while playing back an MP3, WMA* file or DVD-VR (PG/PL) disc, the selected track starts playback automatically.

For UX-G60 only

To start playback

DVD/CD

USB

MEMORY

DVD/CD

USB

ENTER/SET

For JPEG:

ENTER/SET

The selected track (still picture) is displayed until you change it.

Press one of the buttons depending on the current source.

Slide-show playback starts. Each track (still picture) is shown on the screen for about 3 seconds, then changes one after another.

For the other ﬁles:

Playback starts with the selected track.

• Pressing DVD/CD 3 USB MEMORY 3

also

starts playback.

• Once you start viewing a JPEG/MPEG-1/MPEG-2/ ASF*1/DivX track, the control screen disappears.

• To cancel slide-show and display the current still picture, press 8

To select a group:

GROUP/TITLE SKIP

(while holding...)

To repeat MP3 or WMA

playback

While playing or before playback...

REPEAT A-B

REPEAT

REP TRK

REP OFF

(Canceled)

REP GRP

REP ALL

To repeat slide-show for JPEG

While playing or before playback...

REPEAT A-B

REPEAT

To repeat MPEG-1/MPEG-2/ASF

REP GRP REP ALL

REP OFF

(Canceled)

*1/

DivX playback

While playing or before playback...

REPEAT A-B

REPEAT

REP TRK

REP GRP

REP ALL

REP TRK

REP OFF

(Canceled)

*2Repeats the current track.

Repeats the current group.

Repeats the disc.

REP GRP

REP ALL

*2 During Program Play and Random Play, “REP STEP”

appears instead of this indication.

To zoom in the JPEG files

• You cannot zoom in the still picture during slide-show.

While playing back a still picture...

• During slide-show, press 8

to display the still picture,

then...

To skip a track: To stop playback:

GROUP/TITLE SKIP

• You can select a group directly by pressing a number button after pressing GROUP/TITLE (except for DVD-VR disc).

ZOOM

ZOOM 1 ZOOM 2

ZOOM OFF

(while holding...)

Move the zoomed-in position.

TV CH

To cancel Zoom,

repeatedly until “ZOOM OFF” appears on the TV.

For UX-G60 only

press ZOOM (while holding SHIFT)

Advanced Tape Operations

INFO

REC

On the main unit

Remote control

USB MEMORY (UX-G60) FM/AM (UX-G55)

DVD/CD

TAPE FM/AM/AUX

(UX-G60) AUX (UX-G55)

IMPORTANT

It may be unlawful to record or playback copyrighted material without the consent of the copyright owner.

Recording on a Tape

You can use type I tapes for recording.

• To play a tape, see page 9.

Insert a recordable cassette.

Push Insert

With the tape side facing outside

The illustration above is UX-G60.

Select and start playing the source—“FM,” “AM,”

“DVD/CD,” “USB MEM*,” or “AUX.”

• When recording from a disc or USB source, you can also use “Synchronized Recording” (see page 29).

DVD/CD #/

USB MEMORY #/ (UX-G60) FM/AM (UX-G55)

Main unit

Start recording.

PUSH OPEN 0

To stop recording:

FM/AM/AUX (UX-G60)

The illustration above is UX-G60.

AUX (UX-G55)

TAPE REC

For UX-G60 only

Synchronized Recording

INFO

You can start and stop both playback and tape recording at the same time.

To record the entire tracks

Load a disc or connect a USB mass storage class device

*1 and insert a recordable cassette.

• Press DVD/CD 3 current playing source, then 7

Start recording.

REC

On the main unit

• When either playback*2 or recording ends, both playback and recording stop at the same time.

For DVD Video: When a title is finished playing.

• When the tape reaches its end, both playback and recording also stop at the same time.

To record a “Live” disc

It will not be desirable to put 4-second blank portions between the tunes recorded on the tape. To record the entire tracks without any interruption recorded, pause playback (press DVD/CD 3 MEMORY 3

or USB MEMORY 3

The System automatically creates 4-second blanks between the tunes recorded on the tapes.

, then 8

) before pressing REC.

*1 to select the

or USB

To record only your favorite track

You can specify tracks to be recorded on the tape while listening from a disc (except for DVD Video/DVD-VR) or USB mass storage class device*

Start playing a disc/file.

DVD/CD

While a track you want to record on the tape is

USB

MEMORY

playing...

REC

On the main unit

Repeat steps 1 and 2 to record other tracks you want.

• You can change the disc if necessary.

To protect your recording

Cassettes have two small tabs on the back to protect from unexpected erasure or re-recording.

To protect your recording,

Playback returns to the beginning of that track and the track is recorded on the tape. After recording the track, playback and recording automatically stop.

remove these tabs.

To record Program Play

1 Select Program Play (and make a program), but do not

start playback.

2 Press REC to start recording.

• When disc play stops, recording stops automatically.

To re-record on a protected tape,

adhesive tape.

For UX-G60 only

cover the holes with

Enjoying Karaoke

Remote control

RESERVE

USB MEMORY

DVD/CD

AUDIO/MPX

SHIFT

Main unit

KEY KEY

ECHO

KARAOKE

FM/AM /AUX TAPE

NOTE This function is not available for UX-G55.

IMPORTANT

Always set MIC VOLUME to MIN when connecting or disconnecting the microphone.

DO NOT keep the microphone connected while they are not in use.

Singing Along (Karaoke)

INFO

To sing along using the Karaoke discs

You can enjoy Karaoke using the Karaoke disc (except Karaoke CD).

• By pressing REC, you can record your singing-along (for SVCD/VCD without PBC).

Turn MIC VOLUME to MIN.

VOLUME

MAXMIN

Connect the microphone (not supplied) to the MIC

jack.

VOLUMEMIC

MIC jack

MIC VOLUME

DVD/CD #/

USB MEMORY #/

MAXMIN

Insert and start playing a Karaoke disc.

Select an audio track.

AUDIO/MPX

FM/AM/AUX TAPE

REC

• For details, see “Selecting the Audio Track” on page 16.

Sing into the microphone.

Adjust the MIC VOLUME and VOLUME.

VOLUME

MAXMIN

The illustration above is UX-G60.

Karaoke function is not available in the Australian model.

To adjust the Key (disc/file playback only)

Activate Vocal Masking.

Activate Key Control.

(while holding...)

Adjust the Key

ON SCREEN

KARAOKE

KEY KEY

KEYCON

OFF

(Canceled)

V-CANCEL

To raise the key.

To lower the

(while holding...)

key.

• Key Control cannot be activated for DVD Audio/ DVD-VR/MPEG-1/MPEG-2/ASF/DivX.

To deactivate Key Control,

press KARAOKE (while

holding SHIFT) to select “OFF.”

To apply echo to your voice

MENU/PL

ECHO

ECHO ON

ECHO OFF

(Canceled)

ON SCREEN

KARAOKE

(while holding...)

Sing into the microphone. Adjust the MIC VOLUME and VOLUME.

VOLUME

MAXMIN

KEYCON

OFF

(Canceled)

VOLUME

V-CANCEL

• You can apply echo to your voice.

To deactivate Vocal Masking,

select “OFF” in step 4.

Microphone Mixing

You can enjoy microphone mixing while playing any source.

• By pressing REC, you can record your singing-along (except when the playing source is “TAPE”).

Turn MIC VOLUME to MIN.

VOLUME

(while holding...)

To sing along using the stereo discs/audio files —Vocal Masking

You can enjoy Karaoke while playing a stereo disc or an audio file. Vocal Masking reduces the lead vocal of any disc except DVD Audio and DVD-VR.

Turn MIC VOLUME to MIN.

VOLUME

MAXMIN

Connect the microphone (not supplied) to the MIC jack.

Insert and start playing a stereo disc or start playing an audio file.

DVD/CD USB

DVD/CD

USB

MEMORY

Karaoke function is not available in the Australian model.

MAXMIN

Connect the microphone (not supplied) to the MIC

jack.

Start playing the source—“FM,” “AM,” “DVD/CD,”

“USB MEM,” “TAPE,” or “AUX.”

Sing into the microphone.

Adjust the MIC VOLUME and VOLUME.

VOLUME

MAXMIN

VOLUME

• You can apply echo to your voice. While playing a disc, you can also adjust Key Control and apply echo.

• When selecting “TAPE” as the source, microphone mixing is available only during tape playback.

To use the microphone only,

select “AUX” in step 3, but do

not start playback.

Remote

Reserving Karaoke Songs

ONLY

—Karaoke Program Play

You can determine the playback order of the titles or tracks on the disc player. You can program up to 12 steps.

Change the source to “DVD/CD.”

DVD/CD

Start playback.

DVD/CD

Playback starts in the order you have programmed.

To check the programmed contents

During Karaoke Program Play...

The Karaoke reserve screen appears.

Activate Karaoke Program Play.

SET UP

RESERVE

(while holding...)

Gr/Tt

Tr/Chap 1 2 3 4 5

On the TV screen

• PRGM indicator flashes during this mode.

Select songs you want for Karaoke Program Play.

Press the number buttons to select a song in the following order.

Select a title/group.

Select a chapter/track.

Examples:

To select preset number 5,

press 5.

To select preset number 10, press 10.

To select preset number 15, press 10, 1, then 5.

To select preset number 30, press 10, 3, then 0.

To modify the program

While the Karaoke reserve screen is shown on the TV...

To remove the unwanted track:

TV CH

CANCEL

TV CH

(while holding...)

To add another track to the program:

Repeat step 3.

To erase the entire program:

2 sec.

CANCEL

To exit from Karaoke Program Play

Before or after playback...

SET UP

RESERVE

(while holding...)

During playback...

SET UP

RESERVE

(while holding...)

Karaoke function is not available in the Australian model.

Timer Operations

Remote control

AUDIO

CLOCK/TIMER

CANCEL

ENTER/SET

SHIFT

Remote

Setting the Timer

ONLY

Using Daily Timer, you can wake up with your favorite music. On the other hand, with Recording Timer, you can make a tape of a radio broadcast automatically. You can store three Daily Timer settings and one Recording Timer setting; however, you can activate only one of the timers at the same time.

• To exit from the timer setting, press CLOCK/TIMER (while holding SHIFT) as required.

• To correct a mis-entry during process, press CANCEL (while holding SHIFT). You can go back to the previous step.

Daily Timer initial settings when shipped from the factory

• DAILY 1: ON Time (6:00)/OFF Time (8:00)/

Source (TUNER FM 1)/Volume level (– –)

• DAILY 2: ON Time (7:00)/OFF Time (9:00)/

Source (TUNER FM 1)/Volume level (– –)

• DAILY 3: ON Time (10:00)/OFF Time (12:00)/

Source (TUNER FM 1)/Volume level (– –)

INFO

Select one of the timer setting modes you want to set— DAILY 1 ON time, DAILY 2 ON time, DAILY 3 ON time, or REC TMR(Recording Timer) ON time.

CLOCK/TIMER

(while holding...)

DAILY Timer 1

ON (Time)

DAILY 1

Canceled

DAILY Timer 2

ON (Time)

DAILY 2

Clock setting

(see page 15)

MP3

WMA

QPLink S.TURBO PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

USB

MIC

PRGM

3DPHONIC V.MASK C.VOICE

RND

Ex. When Daily Timer 1 setting mode is selected

• When the clock has not been set, pressing CLOCK/ TIMER (while holding SHIFT) makes the System enter the clock setting mode.

Make the timer setting as you want.

Repeat the procedure for the following settings until finished—

Set the hour then the minute for on-time.

1 2

Set the hour then the minute for off-time.

Select the playback source—“TUNER FM,” “TUNER AM,” “TAPE,” “DISC,” “USB MEM

For “TUNER FM” and “TUNER AM”: Select a

QPLink S.TURBO PRGR.

SVCDVD

AHB PRO

B.S.P. BONUS

,” or “AUX.”

MP3

WMA

3DPHONIC V.MASK C.VOICE

USB

MIC

RND

PRGM

preset channel. For “DISC”: Select the title/group number, then the chapter/track number. For “USB MEM

”: Select the group number, then

the track/file number.

DAILY 3

ON (Time)

L-BANDIII

INFO

NEWS

L-BANDIII

INFO

NEWS

DAILY Timer 3

ON (Time)

REC TMR

Recording Timer

MONO

1 23

REC SLEEP A.STBY

REC

ENTER/SET

MONO

1 23

REC SLEEP A.STBY

REC

For UX-G60 only

Continued on the next page

ENTER/SET

Select the volume level.

• You can adjust the volume level (“1” to “40” and “VOL – –”). If you select “VOL – –,” the volume is set to the last level when the unit has been turned off.

Once settings are completed, the Timer setting information appears in sequence.

• This function is not available for VCD with PBC activated.

For Recording Timer:

Set the hour then the minute for on-time.

Set the hour then the minute for off-time.

Select the playback source—“TUNER FM,” “TUNER AM,” or “AUX.”

For “TUNER FM” and “TUNER AM”: Select a preset channel.

Once settings are completed, the Timer setting information appears in sequence. The volume is set to the last level when the unit has been turned off.

Turn off the unit (on standby) if you have set the

on-time.

How Daily Timer works

Once the Daily Timer has been set, the timer indicator () and timer number indicator (1/2/3) are lit on the display. Daily Timer is activated at the same time everyday until the timer is turned off manually (see the next column) or another timer is activated.

When the on-time comes

The System turns on, tunes in to the specified station or starts playing the loaded disc with the specified chapter or track, and sets the volume level gradually to the preset level after about 30 seconds.

• While Daily Timer is working, the timer indicator ( ) and timer number indicator (1/2/3) flash on the display.

When the off-time comes

The System stops playback, and turns off (on standby) automatically.

• The timer setting remains in memory until you change it.

How Recording Timer works

When Recording Timer has been set, Timer ( ) indicator and the REC indicator are lit on the display. Recording Timer works only once.

When the on-time comes

The System turns on, tunes in to the specified station or changes the source to “AUX”, and starts recording.

When the off-time comes

The System stops recording, and turns off (on standby).

• The timer setting remains in memory until you change it.

To turn on or off the Timer

Since Daily Timer is activated at the same time everyday, you may need to cancel it on some particular days.

To cancel the Timer

Select the Timer (DAILY 1, DAILY 2, or DAILY 3) you want to cancel.

CLOCK/TIMER

(while holding...)

DAILY Timer 1

ON (Time)

DAILY 1

Canceled

MP3

WMA

QPLink

SVCDVD

AHB PRO

S.TURBO PRGR.

B.S.P. BONUS

Turn off the selected Timer.

USB

MIC

PRGM

3DPHONIC V.MASK C.VOICE RND

(while holding...)

To turn on the Timer

Select the Timer (DAILY 1, DAILY 2, or DAILY 3)

you want to activate.

(while holding...)

DAILY Timer 1

ON (Time)

DAILY 1

Canceled

Activate the selected Timer.

Wait until the indication disappears.

DAILY Timer 2

DAILY 2

Clock setting

(see page 15)

L-BANDIII

MONO

INFO

NEWS

SLEEP A.STBY

REC

CANCEL

ON (Time)

1 23

REC

DAILY Timer 3

ON (Time)

DAILY 3

ON (Time)

REC TMR

Recording Timer

Ex. To cancel Daily

Timer 1

CLOCK/TIMER

DAILY Timer 2

ON (Time)

DAILY 2

Clock setting

(see page 15)

QPLink

SVCDVD

AHB PRO

S.TURBO PRGR.

B.S.P. BONUS

Ex. When Daily Timer 1 (DAILY 1) is

activated

DAILY 3

ON (Time)

MP3

WMA

3DPHONIC V.MASK C.VOICE

USB

MIC

RND

PRGM

DAILY Timer 3

ON (Time)

REC TMR

Recording Timer

L-BANDIII

FM ST

INFO

NEWS

SLEEP A.STBY

REC

MONO

1 23

REC

Remote Control

Setup Menu Operations

Initial settings

The Setup Menu cannot be activated during playback.

Press SET UP.

LANGUAGE

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

ENGLISH

INFO

Remote ONLY

,, ,

SET UP

LANGUAGE menu

Item

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

PICTURE menu

Item

MONITOR TYPE

16:9 4:3 LB

4:3 PS

ENTER/SET

Press ( Press (

Press ENTER/SET.

4 5

Press (

)to select the menu.

or )

to move to select the item.

or )

to select the options, then press

ENTER/SET.

• For settings of the LANGUAGE menu, see also “Language Code List” on page 42.

To remove a preference display

Press SET UP.

Contents

You can select the initial menu language of the DVD Video.

You can select the initial audio language of the DVD Video.

You can select the initial subtitle language of the DVD Video.

You can select “ENGLISH,” “CHINESE,” or “SPANISH” as the on-screen language.

Contents

You can select the monitor type to match your TV when you playback DVD Video discs recorded for wide-screen televisions.

16:9/16:9 MULTI (Wide television screen): 4:3 LB/4:3 MULTI LB (Letter Box conversion):

wide-screen picture to fit the width of the TV screen keeping the aspect ratio.

4:3 PS/4:3 MULTI PS (Pan Scan conversion):

in to fill the screen vertically and the left and right sides of the picture are cut off.

• For multi-color system TVs, select the [MULTI] option.

For a wide-screen (16:9) TV.

For a conventional (4:3) TV. Displays a

For a conventional (4:3) TV. The picture is zoomed

PICTURE SOURCE

SCREEN SAVER

FILE TYPE

You can obtain optimal picture quality by selecting the source type of the disc contents.

AUTO:

Normally, select this option. The System recognizes the picture type (film or video source) of

the current disc according to the disc information.

FILM:

For a film source disc.

VIDEO:

You can set the screen saver function to ON or display dims.

You can select the file type to play.

AUDIO: STILL PICTURE: VIDEO:

For a video source disc.

OFF.

If no operation is done for about 5 minutes, the

To play MP3 and WMA (for UX-G60 only) files.

To play MPEG-1, MPEG-2, ASF (for UX-G60 only) and DivX files.

To play JPEG files.

AUDIO menu

Item

DIGITAL AUDIO OUTPUT

DOWN MIX

D. RANGE COMPRESSION

OTHERS menu

Item

RESUME

ON SCREEN GUIDE

DivX REGISTRATION

Contents

Set this item correctly when using the OPTICAL DIGITAL OUT terminal on the rear.

PCM ONLY: DOLBY DIGITAL/PCM:

in Dolby Digital decoder.

STREAM/PCM:

This setting is effective for digital audio output if “DIGITAL AUDIO OUTPUT” is set to “PCM ONLY.”

DOLBY SURROUND: STEREO:

Set this item to listen to DVD Video recorded in Dolby Digital format at low or middle volume.

AUTO: ON:

Select this when you want to fully apply the compression effect to make the sound at lower

volume clear (useful at midnight).

When connecting to audio equipment which can decode only linear PCM signals.

When connecting to a Dolby Digital decoder or an amplifier with a built-

When connecting to a DTS decoder or an amplifier with a built-in DTS decoder.

Select this when connecting to a surround decoder.

Select this when connecting to a stereo receiver, MD player, TV, etc.

You can enjoy powerful playback sound with full dynamic range.

Contents

You can select Resume.

ON:

The System resumes playback from the position where playback has been stopped if the disc is

still in the disc tray.

OFF:

Resume is deactivated.

Activate or deactivate the on-screen guide.

The System has its own Registration Code. If necessary, you can confirm it. Once you have played back a disc in which the Registration Code is recorded, the System’s Registration Code is overwritten for copyright protection.

Additional Information

Learning More about This System

Connections

• Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away from metallic parts of the System, connecting cords and the AC power cord. This could cause poor reception.

• Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.

• The speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, it may cause color distortions. So, pay attention to the following when installing the speakers. – When placing the speakers near a TV set, turn off the

TV’s main power switch or unplug it before installing the speakers. Then wait at least 30 minutes before turning on the TV’s main power switch again.

– Some TVs may still be affected even though you have

followed the above instructions. If this happens, move the speakers away from the TV.

Daily Operations—Playback

Listening to the Radio:

• If you store a new station into an occupied preset number, the previously stored station in that number will be erased.

• When you unplug the AC power cord or if a power failure occurs, the preset stations will be erased in a few days. If this happens, preset the stations again.

Playing Back a Disc/File:

• When you change the source to DVD/CD or USB MEMORY (for UX-G60 only), it may take a while to activate the source.

• On some DVD, SVCD, or VCD discs, the actual operations may be different from what is explained in this manual, due to the programming and disc structure; such differences are not a malfunction of this System.

• This System can recognize up to 4 000 tracks in a disc. Also, the System can recognize up to 150 tracks per group and up to 99 groups in a disc. – If there are any unplayable files in a folder, those files are

also counted in the total file number.

– Playable files which do not belong to any groups are

handled as group 1.

• For DVD-VR playback... – This System can play only a disc of UDF-Bridge format. – For details about DVD-VR format and play list, refer to

the manual of the recording equipment.

– You cannot use reverse slow motion, Program Play, or

Random Play.

• For MP3 or WMA (for UX-G60 only) playback... – MP3/WMA discs require a longer readout time than

regular CDs. (It depends on the complexity of the group/ file configuration.)

(see pages 3 to 5)

(see pages 7 to 11)

– Some MP3/WMA files cannot be played back and will

be skipped. This results from their recording processes and conditions.

– This System can play only a disc of ISO 9660 Level 1 or

Level 2.

– This System can playback MP3/WMA files with the

extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

– It is recommended that you make each MP3/WMA file at

a sampling rate of 44.1 kHz and at a bit rate of 128 kbps. This System cannot playback files made at a bit rate of less than 64 kbps.

• For JPEG files playback... – It is recommended that you record a file at 640 x 480

resolution. (If a file has been recorded at a resolution of more than 640 x 480, it will take a long time to be shown.)

– This System can play only baseline JPEG files*.

Progressive JPEG files* or lossless JPEG files* cannot be played. * Baseline JPEG format: Used for digital cameras,

web, etc. Progressive JPEG format: Used for web. Lossless JPEG format: An old type and rarely used

now.

– This System can playback JPEG files with the extension

code <.jpg> or <.jpeg> (regardless of the letter case— upper/lower).

– This System may not playback JPEG files properly if

they are recorded from a device other than a digital camera.

– During slide-show playback, zoom cannot be operated.

• For MPEG-1/MPEG-2 playback... – The stream format should conform to MPEG system/

program stream.

– 720 x 576 pixels (25 fps)/720 x 480 pixels (30 fps) is

recommended for the highest resolution.

– This System also supports the resolutions of 352 x 576/

480 x 576/352 x 288 pixels (25 fps) and 352 x 480/480 x 480/352 x 240 pixels (30 fps).

– The file format should be MP@ML (Main Profile at

Main Level)/SP@ML (Simple profile at Main Level)/ MP@LL (Main Profile at Low Level).

– Audio streams should conform to MPEG1 Audio layer-2

or MPEG2 Audio Layer-2.

• For DivX playback... – This System can play only a disc of UDF-Bridge format.

“Multi-border” is not supported.

– The System supports DivX files whose resolution is 720

x 480 pixels or less (30 fps), and 720 x 576 pixels or less (25 fps).

– Audio stream should conform to MPEG1 Audio Layer-2

or MPEG Audio Layer-3 (MP3).

– This System can playback DivX files with the extension

code <.divx> <.div> <.avi> (regardless of the letter case—upper/lower).

– The System does not support GMC (Global Motion

Compression).

– The file encoded in the interlaced scanning mode may

not be played back correctly.

– You cannot use the following functions—One Touch

Replay, Slow motion, A-B Repeat, Program Play, Random Play and on-screen operations.

Playing Back a Disc/File for UX-G60:

• Some DVD Audio discs prohibit downmix. When you playback such a disc, “LR ONLY” appears on the display and the System plays back the left front and right front signals.

• When playing back a DVD Audio disc recorded in MLP (Meridian Lossless Packing; a lossless audio compression system that can completely recreate the PCM signal), the signals are recognized as the linear PCM signals, however, no indicator lights up on the display.

• While the System is reading a disc, changing the source to USB MEMORY may cause the System to continue playback the DVD/CD source. In this case, press 7 main unit to reactivate the USB source.

• The following functions cannot be used for the files in the USB mass storage class device: – Selecting the View Angle (page 17) – Special Effect Playback (page 18) – Program Play (page 19) – A-B Repeat (page 21) – Time Search (page 24)

• For playback of files in the USB mass storage class device... – When connecting a USB mass storage class device, refer

also to its manual.

– Connect one USB mass storage class device to the

System at a time. Do not use a USB hub.

– You cannot charge any USB device through the USB

MEMORY jack of this System.

– While playing back a file in a USB mass storage class

device, do not disconnect the device. It may cause a malfunction of both the System and the device.

– JVC bears no responsibility for any loss of data in the

USB mass storage class device while using this System.

– When connecting with a USB cable, use the cable whose

length is less than 1 m.

– This System is compatible with the USB Full-Speed (not

compatible with the USB 1.1).

– You can playback the following types of files in a USB

mass storage class device (maximum data transfer rate: 2 Mbps): – Music: MP3, WMA – Picture: JPEG – Movie: MPEG-1, MPEG-2, ASF, DivX (maximum

frame rate of 30 fps for progressive)

on the

– You cannot playback a file larger than 2 Gigabyte. – When playing a file which has a large transfer rate,

frames or sounds may be dropped during playback.

– This System cannot recognize a USB mass storage class

device whose rating is other than 5 V and does not exceed 500 mA.

– This System may not playback some USB mass storage

class devices and does not support DRM (Digital Rights Management).

– This System may not playback some files even though

their formats are listed above.

• For ASF playback... – This System can playback ASF files with the extension

code <.asf> (regardless of the letter case—upper/lower).

– This System supports ASF files whose resolution is 352

x 288 pixels or less.

– Some recorded files may not be able to playback

depending on file characteristics, kind of digital camera/ video camera, or recording conditions.

– You cannot use the following functions—One Touch

Replay, Slow motion, A-B Repeat, Program Play and Random Play.

Playing Back a Portable Audio Device:

• When QP Link fails due to a weak sound signal from the AUX jack, Auto Standby may turn the System off even if you can hear the sound from the speakers. In such cases, adjust the volume level of the component

louder so that the System can detect the sound signal properly.

• Changing from AUX to another source while QP Link works will deactivate QP Link temporarily. In this case, the following reactivates QP Link: – Pressing QP LINK on the remote control twice. – Unplug the component from the AUX jack, then plug it

in again.

• If you press preset Timer turns the System off while QP Link works, the System will deactivate QP Link temporarily. In such cases, the following reactivates QP Link: – When the sound signal from the AUX jack stops or is too

weak for about 30 seconds after the System is turned off.

– When you turn on the power again.

• QP Link may start working when you just plug in the component to the AUX jack or unplug it. This is not a malfunction.

(Standby/on) to turn the System off or if

Daily Operations—Sound & Other Adjustments

(see pages 12 to 15)

Adjusting the Sound:

• This function also affects the sound through the headphones.

Changing the Scanning Mode (for UX-G60 only):

• You cannot change the scanning mode to progressive in the following cases: – When your TV does not support the progressive video

input.

– When you have not connected your TV to the system

using a component video cord.

Setting the Clock:

• “0:00” will flash on the display until you set the clock.

• The clock may gain or lose 1 to 2 minutes per month. If this happens, reset the clock.

Unique DVD/VCD Operations

Selecting the Audio Track:

• On some DVD Video discs, you cannot change audio languages while playing back.

Special Effect Playback:

• During slow-motion playback, no sound will be reproduced.

• While zoomed in, the picture may look coarse.

Advanced Playback Operations

to 25)

Programming the Playing Order—Program Play:

• While programming steps... Your entry will be ignored if you have tried to program an item number that does not exist (for example, selecting track 14 on a disc that only has 12 tracks).

Playing Repeatedly:

• A-B Repeat can be used within the same title while playing a DVD Video, and within the same track for the other discs.

On-screen Disc Operations:

• For DVD-R/-RW in the VR format, “PG” or “PL” appears instead of “TITLE” on the on-screen bar.

Audio/Video File Operations

and 27)

Operations on the Control Screen:

• If you press ON SCREEN on the remote control during playback, playback information appears on the TV screen.

Advanced Tape Operations

Recording on a Tape:

• The recording level is automatically set correctly. Thus, you can adjust the sound you are actually listening to without affecting the recording level.

(see pages 16 to 18)

(see pages 19

(see pages 26

(see pages 28 and 29)

• There is leader tape which cannot be recorded onto at the start and end of cassette tapes. Thus, when recording CDs or radio broadcasts, wind the leader tape first to ensure that the recording will be made without any music part lost.

• If you start recording with no cassette inserted, “NO REC” appears on the display. If a protected tape has been inserted, “NO REC” appears.

• You cannot open or close the disc tray while recording a disc.

Synchronized Recording:

• Synchronized recording does not function on the file format of MPEG-1, MPEG-2, ASF*, and DivX.

Enjoying Karaoke

to 32) (Not available in the Australian model)

Singing Along (Karaoke):

• Karaoke mode setting (Key Control and Vocal Masking) can be used when selecting “DVD/CD” or “USB MEMORY” as the source, except for DVD-VR/DVD Audio/MPEG-1/MPEG-2/ASF/DivX files. Even if the source is “DVD/CD” or “USB MEMORY,” Karaoke mode setting cannot be used while “NO DISC” or “NO DEVICE” appears on the display.

• Karaoke mode setting is automatically canceled when the source is changed.

• When selecting “DVD/CD” or “USB MEMORY” as the source, the microphone is not available while playback is stopped or paused. To use the microphone, activate Key Control or Vocal Masking.

• Karaoke mode setting is also applied to the optical digital output signals.

• When Vocal Masking is activated, 3D Phonic will be canceled temporarily.

• On some music discs, Vocal Masking does not provide the correct effect.

• You can also use the microphone when selecting “FM,” “AM,” or “AUX” as the source. When selecting “TAPE” as the source, you can use the microphone only during tape playback.

Timer Operations

Setting the Timer:

• If you do not specify the preset station or track number correctly while setting a timer, the currently selected station or the first track will be played when the timer is activated.

• When you unplug the AC power cord or if a power failure occurs, the timer will be canceled. You need to set the clock first, then the timer again.

• If you set DVD Video as the source, Daily Timer will not work correctly.

Timer Priority:

• If you set the Sleep Timer after Daily Timer starts playing the selected source, Daily Timer is canceled.

(for UX-G60 only) (see pages 30

(see pages 33 and 34)

For UX-G60 only

Setup Menu Operations

General:

• If the upper and lower parts of the menu are cut off, adjust the picture size control of the TV.

LANGUAGE menu:

• When the language you have selected for MENU LANGUAGE, AUDIO LANGUAGE, or SUBTITLE is not recorded on a disc, the original language is used as the initial language.

PICTURE menu—MONITOR TYPE:

• Even if “4:3 PS/4:3 MULTI PS” is selected, the screen size may become 4:3 letter box while playing a disc. This depends on how the discs are recorded.

• When you select “16:9/16:9 MULTI” for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.

OTHERS menu—ON SCREEN GUIDE:

• The setup menu and on-screen bar will be displayed (and recorded) even though this function is set to “OFF.” Subtitles and the information for zoom-in always appear on the display regardless of this setting.

(see pages 35 and 36)

Maintenance

To get the best performance of the System, keep your discs, tapes and mechanism clean.

Handling discs

• Remove the disc from its case by holding it at the edge while pressing the center hole lightly.

• Do not touch the shiny surface of the disc, or bend the disc.

• Put the disc back in its case after use to prevent warping.

• Be careful not to scratch the surface of the disc when placing it back in its case.

• Avoid exposure to direct sunlight, extreme temperature, and moisture.

To clean the disc:

Wipe the disc with a soft cloth in a straight line from center to edge.

Cleaning the System

• Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in waterdiluted neutral detergent and wrung well, then wipe clean with a dry cloth.

• Since the System may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following: – DO NOT wipe it with a hard cloth. – DO NOT wipe it forcefully. – DO NOT wipe it with thinner or benzine. – DO NOT apply any volatile substance such as

insecticides to it.

– DO NOT allow any rubber or plastic to remain in contact

for a long time.

To remove the speaker grilles (for UX-G60 only):

Speaker grille

Holes

Projection

Handling cassette tapes

• If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotate it. – If the tape is loose, it may get stretched, cut, or caught in the

cassette.

• Be careful not to touch the tape surface.

• Avoid the following places to store the tape—in dusty places, in direct sunlight or heat, in moist areas, on a TV or speaker, or near a magnet.

To keep the best recording and playback sound quality:

• Use a cotton swab moistened with alcohol to clean the heads, capstans, and pinch rollers.

• Use a head demagnetizer (available at electronics and audio shops) to demagnetize the heads (when the System turned off).

Troubleshooting

General:

Adjustments or settings are suddenly canceled before you finish.

]

There is a time limit. Repeat procedure again.

Operations are disabled.

]

The built-in microprocessor may malfunction due to external electrical interference. Unplug the AC power cord and then plug it back in.

Unable to operate the System from the remote control.

]

The path between the remote control and the remote sensor on the System is blocked.

]

The batteries are exhausted.

No sound is heard.

]

Speaker connections are incorrect or loose.

]

Headphones are connected.

No picture appears on the screen.

]

The video cord connections are incorrect or loose.

No picture is displayed on the TV screen, the picture is blurred, or the picture is divided into two parts.

]

The System is connected to a TV which does not support progressive video input.

The left and right edges of the picture are missing on the screen.

]

Select “4:3 LB” for “MONITOR TYPE” (see page 35).

Radio Operations:

Hard to hear broadcasts because of noise.

]

Antennas connections are incorrect or loose.

]

The AM loop antenna is too close to the System.

]

The FM antenna is not properly extended and positioned.

Disc/File Playback Operations:

The disc does not play.

]

You have inserted a disc whose Region Code is not correct. (“RG ERROR” appears on the display.)

]

The disc is placed upside down. Place the disc with the label side up.

ID3 Tag on an MP3 or WMA* file cannot be shown.

]

There are two types of ID3 Tag—Version 1 and Version 2. This System can only show ID3 Tag Version 1.

Groups and tracks are not played back as you expect.

]

The playing order is determined when the groups and tracks were recorded. It depends on the writing application.

MP3, WMA*, JPEG, MPEG-1, MPEG-2, ASF* or DivX files are not played back.

]

The disc or the USB mass storage class device* may include both type of tracks (MP3 or WMA* ﬁles and JPEG ﬁles). In this case, you can only playback the ﬁles selected by the “FILE TYPE” setting (see page 35).

]

You have changed the “FILE TYPE” setting after the System read the disc or the USB mass storage class device*. In this case, reload the disc or disconnect the USB mass storage class device* and connect it again.

“NO AUDIO” appears.

]

This System cannot playback illegally produced DVD Audio discs.

“LR ONLY” appears.

]

Some DVD Audio discs prohibit downmixed output. When you playback such a disc, this System plays back the left front and right front signals only.

The disc sound is discontinuous.

]

The disc is scratched or dirty.

No subtitle appears on the display though you have selected the initial subtitle language.

]

Some DVDs are programmed to always display no subtitle initially. If this happens, press SUBTITLE after starting playback (see page 17).

Audio language is different from the one you have selected as the initial audio language.

]

Some DVDs are programmed to always use the original language initially. If this happens, press AUDIO/MPX after starting playback (see page 16).

The disc tray does not open or close.

]

The AC power cord is not plugged in.

]

Child Lock is in use. “LOCKED” appears in the display window (see page 21).

Tape Operations:

The cassette holder cannot be opened.

]

Power supply from the AC power cord has been cut off while the tape was running. Turn on the System.

QP Link Operations:

The System automatically turns on even if the Timer turn the System to standby or if you turn the System to standby while playback is going on the portable audio device.

]

In this case, deactivate QP Link or stop playback on the device connected to the AUX jack.

Recordings:

Impossible to record.

]

Small tabs on the back of the cassette are removed. Cover the holes with adhesive tape.

Timer Operations:

Daily Timer does not work.

]

The System has been turned on when the on-time comes. Timer starts working only when the System is turned off.

Daily Timer does not start playback.

]

The disc loaded is a DVD Video. Change the disc.

]

Title/group number and chapter/track number are not entered while setting the Daily Timer. Do not skip these steps when you want to play a disc using Daily Timer.

For UX-G60 only

Language Code List

Afar

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali, Bangla

Tibetan

Breton

Catalan

Corsican

Czech

Welsh

Danish

Bhutani

Greek

Esperanto

Estonian

Basque

Persian

Finnish

Fiji

Faroese

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Interlingue

Inupiak

Indonesian

Icelandic

Hebrew

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean (KOR)

Kashmiri

Kurdish

Kirghiz

Latin

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonian

Malayalam

Mongolian

Moldavian

Marathi

Malay (MAY)

MT Maltese

MY Burmese

NA Nauru

NE Nepali

NL Dutch

NO Norwegian

OC Occitan

OM (Afan) Oromo

OR Oriya

PA Panjabi

PL Polish

PS Pashto, Pushto

PT Portuguese

QU Quechua

RM Rhaeto-Romance

RN Kirundi

RO Rumanian

RW Kinyarwanda

SA Sanskrit

SD Sindhi

SG Sangho

SH Serbo-Croatian

SI Singhalese

SK Slovak

SL Slovenian

SM Samoan

SN Shona

SO Somali

SQ Albanian

SR Serbian

SS Siswati

ST Sesotho

SU Sundanese

SV Swedish

SW Swahili

TA Tamil

TE Telugu

TG Tajik

TH Thai

TI Tigrinya

TK Turkmen

TL Tagalog

TN Setswana

TO Tonga

TR Turkish

TS Tsonga

TT Tatar

TW Twi

UK Ukrainian

UR Urdu

UZ Uzbek

VI Vietnamese

VO Volapuk

WO Wolof

XH Xhosa

YO Yoruba

ZU Zulu

OPTICAL DIGITAL OUT Signals

DIGITAL AUDIO

OUTPUT

Playback disc/file STREAM/PCM DOLBY DIGITAL/PCM PCM ONLY

DVD Video

with 48 kHz, 16/20/24 bit Linear PCM

with 96 kHz, Linear PCM 48 kHz, 16 bit Linear PCM

with Dolby Digital Dolby Digital bitstream 48 kHz, 16 bit Linear PCM

with DTS DTS bitstream 48 kHz, 16 bit Linear PCM

DVD Audio

DVD-R/-RW/-ROM in DVD-VR format

SVCD, VCD, CD

CD with DTS

MP3/WMA

ASF

*1For UX-G60 only *2While playing some DVDs, digital signals may be emitted at 20 bits or 24 bits (at their original bit rate) through the OPTICAL DIGITAL

OUT terminal if the discs are not copy-protected.

with 48/96/192 kHz, 16/20/24 bit Linear PCM

with 44.1/88.2/176.4 kHz, 16/20/24 bit Linear PCM

with Dolby Digital Dolby Digital bitstream 48 kHz, 16 bit Linear PCM

with DTS DTS bitstream 48 kHz, 16 bit Linear PCM

with 48 kHz, 16/20/24 bit Linear PCM

with Dolby Digital Dolby Digital bitstream 48 kHz, 16 bit Linear PCM

44.1 kHz, 16 bit Linear PCM/48 kHz, 16 bit Linear PCM

DTS bitstream 44.1 kHz, 16 bit Linear PCM

*1/DivX disc/file

*1 disc/file

32/44.1/48 kHz, 16 bit Linear PCM

Output Signals

48 kHz, 16 bit Linear PCM*

48 kHz, 16 bit Linear PCM

44.1 kHz, 16 bit Linear PCM

48 kHz, 16 bit Linear PCM*

32 kHz, 16 bit Linear PCM

Operating JVC’s TVs Using the Remote Control

Remote control

TV/VIDEO

TV CH ,

TV VOL

SHIFT

+,–

You can use the remote control to operate JVC’s TVs.

TV/VIDEO

Turn on/off TV.

Change the input mode.

While holding SHIFT, press...

TV VOL +,–

TV CH ,

Adjust the volume.

Change the channels.

Specifications

Amplifier section

CA-UXG60 (for UX-G60)/CA-UXG55 (for UX-G55)

Output Power:

CA-UXG60: 120 W (60 W + 60 W) at 6 Ω (10% THD) CA-UXG55: 50 W (25 W + 25 W) at 6 Ω (10% THD)

Audio Input AUX: 500 mV/50 kΩ (at “AUX LVL1”)

Digital output: OPTICAL DIGITAL OUT:

Digital input: USB MEMORY Video Out:

Color system: NTSC or PAL (interlaced/progressive*) VIDEO (composite): 1 V(p-p)/75 S-VIDEO:Y (luminance) 1 V(p-p)/75

C (chrominance, burst)

COMPONENT: (Y) 1 V(p-p)/75

Speaker impedance: 6 Ω – 16

Tuner section

FM tuning range: 87.50 MHz – 108.00 MHz AM (MW) tuning range:

For Saudi Arabia only:

Tape section

Frequency response: 60 Hz – 14 000 Hz Wow and flutter: 0.15 % (WRMS)

Disc/file player section

Region codes:

Middle East: 2 South East Asia, Hong Kong region: 3 Central and South America, Australia: 4

Playable disc:

DVD Video/DVD Audio*/CD/VCD/SVCD/CD-R/CDRW (CD/SVCD/VCD/MP3/WMA*/JPEG/MPEG-1/ MPEG-2/ASF*/DivX format) DVD-R/-RW (DVD-VR/DVD Video/MP3/WMA*/JPEG/ MPEG-1/MPEG-2/ASF*/DivX format) +R/+RW(DVD-Video format) DVD-ROM (DVD Video/DivX format)

Playable file:

MP3/WMA*/JPEG/MPEG-1/MPEG-2/ASF*/DivX format

Dynamic range: 80 dB Horizontal resolution: 500 lines Wow and flutter: Immeasurable

General

Power requirement:

AC 110 V/AC 127V/AC 220 V/AC 230 V-240V

(adjustable with the voltage selector), 50 Hz/60 Hz For Hong kong: AC 220 V , 50 Hz For Oceanian countries: AC 240 V , 50 Hz

250 mV/50 kΩ (at “AUX LVL2”) 125 mV/50 kΩ (at “AUX LVL3”)

–21 dBm to –15 dBm (660 nm ±30 nm)

(for CA-UXG60 only)

Ω Ω

NTSC 0.286 V(p-p)/75 PAL 0.3 V(p-p)/75

Ω

(PB/PR) 0.7 V(p-p)/75

Ω

531 kHz – 1 710 kHz (at 9 kHz intervals)

530 kHz – 1 710 kHz (at 10 kHz intervals)

531 kHz – 1 602 kHz (at 9 kHz intervals)

530 kHz – 1 600 kHz (at 10 kHz intervals)

Power consumption (UX-G60/UX-G55):

125 W/65 W (at operation)

14 W/11 W (at standby)

3.5 W/3.5 W (at standby dimmer OFF mode)

Dimensions (approx.): 170 mm x 250 mm x 342 mm

Mass (approx.): UX-G60: 5.7 kg/UX-G55: 4.7 kg

Speaker section

SP-UXG63 (for UX-G60)

Speaker units: Tweeter: 1.5 cm dome x 1

Squawker: 4 cm cone x 1

Woofer: 13.5 cm cone x 1 Impedance: 6 Dimensions (approx.): 166 mm x 250 mm x 232 mm

Mass (approx.): 2.8 kg each

SP-UXG55 (for UX-G55)

Speaker units: 10 cm cone x 1

Ω

Impedance: 6 Dimensions (approx.): 145 mm x 250 mm x 200 mm

Mass (approx.): 2 kg each

Supplied Accessories

See page 3.

Design and specifications are subject to change without notice.

• Manufactured under license from Dolby Laboratories. “Dolby”,

“Pro Logic”, “MLP lossless”, and the double-D symbol are trademarks of Dolby Laboratories.

• “DTS” and “DTS 2.0+ Digital Out” are trademarks of Digital

Theater Systems, Inc.

• “Official DivX® Certified product” “Plays all versions of DivX®

video (including DivX® 6) with standard playback of DivX media files” “DivX, DivX certified, and associated logos are trademarks of DivX, Inc. and are used under licence.”

• “Official DivX® Ultra Certified product” “Plays all versions of

DivX® video (including DivX® 6) with enhanced playback of DivX® media files and the DivX® Media Format” “DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under licence.”

• USE OF THIS PRODUCT IN ANY MANNER THAT

COMPLIES WITH THE MPEG-4 VISUAL STANDARD IS PROHIBITED, EXCEPT FOR USE BY A CONSUMER ENGAGING IN PERSONAL AND NON-COMMERCIAL ACTIVITIES.

• This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited. “CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.”

(W/H/D)

Ω

(W/H/D)

Ω

(W/H/D)

For UX-G60 only

Parts Index

Remote control

Button Page

AUDIO TV

¡¡¡¡ , 11

¢¢¢¢ , 44 88

,,,

, ENTER/SETq9, 11, 14, 15, 18, 23, 25, 27, 33, 34, 35

(One-Touch Replay) 3D PHONIC AHB PRO ANGLE AUDIO/MPX AUDIO VOL + , – AUX (UX-G55) A.STANDBY BASS/TREBLE C.VOICE CANCEL CLOCK/TIMER DIMMER DISPLAY DVD/AUX LEVEL

DVD/CD 33 ECHO (UX-G60) FADE MUTING FM/PLAY MODE FM/AM (UX-G55) FM/AM/AUX (UX-G60) GROUP/TITLE GROUP/TITLE SKIP KARAOKE (UX-G60) KEY (UX-G60) MENU/PL NTSC/PAL (UX-G55) Number buttons ON SCREEN PAGE (UX-G60) QP LINK REPEAT REPEAT A-B RESERVE (UX-G60)* RETURN SCAN MODE (UX-G60) SET UP SHIFT SLEEP SLOW 9999 , (( SOUND TURBO II SUBTITLE TAPE TOP MENU/PG TV CH 9999 , (( TV VOL + , – TV/VIDEO USB MEMORY 3333 (UX-G60)e7, 10, 27, 28, 29, 31 VFP ZOOM

((

10, 11, 18, 20, 27, 28, 29

9, 10

9, 10, 11, 20, 27

10, 18, 20, 27, 29

;

16, 30

7, 13

7, 10

20, 34

15, 33, 34

7, 10, 27

8, 19, 20

7, 8, 28

10, 27

11, 25

9, 11, 18, 19, 24, 25

;

10, 11, 13, 14, 15, 17, 18, 21, 27, 31, 32, 33, 34, 43

11, 25

18, 27

Main unit

Button Page

& STANDBY lamp

77 00

3D-PHONIC AUX (UX-G55) AUX jack Cassette holder Display DISPLAY DVD/CD ####/88 FM/AM (UX-G55) FM/AM/AUX (UX-G60) MIC jack (UX-G60)* MIC VOLUME (UX-G60)*

10, 21

9, 28

7, 10, 27, 28, 29, 31

7, 8, 28

30, 31

PHONES REC Remote sensor SOUND TURBO II TAPE

¢¢¢¢ UP, DOWN 44

USB MEMORY jack (UX-G60) USB MEMORY ##

VOLUME + , –

/88

(UX-G60)

28, 29, 30

8, 20

(

7, 10, 27, 28, 29, 31

12, 30, 31

Remote control

1 2 3 4 5

6 7

10 0

9 p q w e r t y

u i o ; a s d

This remote control can also operate JVC’s TVs (see page 43).

Main unit

4 5 6

8 9 0

The illustration above is UX-G60.

* Not on the Australian model.

f g

h j

k l / z x

c v b n m , .

P Q

! @ #

% ^

(

Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia, and U.K.)

VOLTAGE

SELECTOR

VOLTAGE

SELECTOR

127V

110V

230V

-240V

110V

127V

220V

UX-G60

UX-G55 MICRO COMPONENT SYSTEM

220V

230V

-240V

The illustration above is UX-G60 (except for Hong Kong region and Australia).

CAUTION for mains (AC) line

BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.

0206JSKMDCJEM

JVC UX-G60, UX-G55 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual