JVC RX-774PBK, RM-SR774XU, LVT0014-001A User Manual

AUDIO/VIDEO CONTROL RECEIVER
RECEPTOR DE CONTROL DE AUDIO/VÍDEO RECEPTOR DE COMANDO AUDIO/VÍDEO
RX-774PBK
RM-SR774XU REMOTE CONTROL
TV/CATV
VCR
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
MUTE
N
W
O
D
PLAY
G
N
I
N
U
T
4 / REW
REC
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
O
N
S
C
R
E
SLEEP
CNTR
213
REAR (L)
ENTER
546
(REAR R)
87/P9 0
FM MODE/MUTE
CHANNEL
N
I
N
U
T
FF / ¢
PAUSE
STOP
TV VOLUME
M
U
E
R
N
T
N
O
E
C
N
AUDIO
MENU
+10
100+
P
U
G
L
O
RX-774P AUDIO/VIDEO CONTROL RECEIVER
STANDBY
STANDBY/ON
POWER
_ ON OFF
PHONES
COMPULINK
Remote
ENHANCED COMPULINK CONTROL SYSTEM
SPEAKERS
12
DOLBY SURROUND
DSP MODE
BALANCE/SURROUND
ADJUST
DVD MULTI/2CH
SEA MODE
SEA ADJUST SETTING
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECT LOUDNESS ONE TOUCH OPERATION
SOURCE NAME
MULTI JOG
DVD
TV SOUND/DBS PHONO
SOURCE SELECTOR
CD
TAPE/MDVCR
FM
AM
MASTER VOLUME
+
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRUÇÕES
For Customer Use:
Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No. Serial No.
LVT0014-001A
Warnings, Cautions and Others / Avisos, precauciones y otras notas / Advertêcias, precauções e outras notas /
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
PRECAUCIÓN
Para reducir riesgos de choques eléctricos, incendio, etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2. No exponga este aparato a la lluvia o a la humedad.
ATENÇÃO
Para reduzir riscos de choques eléctricos, incêndio, etc.:
1. Não retire parafusos nem desmonte as tampas ou o gabinete.
2. Não exponha este aparelho à chuva nem à umidade.
Caution –– POWER switch and STANDBY/ON button!
This apparatus is provided with a POWER switch to be able to minimize power consumption for safe use. Therefore,
1. When doing initial setting, complete all the connections required, connect the mains plug into the wall outlet, and set the POWER switch to ON. After these, it will be available to operate STANDBY/ON button and so on.
2. When not in use, set the POWER switch to OFF.
3. Disconnect the mains plug to shut the power off completely. The POWER switch and STANDBY/ON button in any position do not disconnect the mains line.
4. The power can be remote controlled.
Precaución –– Interruptor POWER y botón STANDBY/ON !
Esta unidad dispone de un interruptor POWER que sirve para reducir al mínimo el consumo de alimentación para proporcionar mayor seguridad operacional. Por lo tanto,
1. Al ejecutar el ajuste inicial, después de completar todas las conexiones requeridas, conectar el cable de alimentación a una toma de pared, y activar el interruptor POWER. Entonces, será posible ejecutar operaciones tales como la conmutación del estado de alimentación.
2. Desactivar el interruptor POWER al dejar la unidad fuera de uso.
3. Desconectar el cable de alimentación para desactivar la alimentación totalmente. Cualquier que sea la posición de ajustes del interruptor POWER y el botón STANDBY/ON , la alimentación no es cortada completamente.
4. La alimentación puede ser controlada remotamente.
Precaução –– Interruptor POWER e botão STANDBY/ON !
Este aparelho dispõe de um interruptor POWER que possibilita reduzir ao mínimo o seu consumo de energia por medida de segurança. Assim,
1. Nos ajustes iniciais, efetue todas as conexões necessárias, ligue o plugue de alimentação à tomada e coloque o interruptor POWER em ON. Feito isso, será possível operar o botão STANDBY/ON e as diversas funções.
2. Quando não utilizar o aparelho, coloque o interruptor POWER em OFF.
3. Remova o plugue de alimentação da tomada para desligar o aparelho completamente. O interruptor POWER e o botão STANDBY/ ON , em qualquer de suas posições, não desligam a alimentação do aparelho.
4. É possível controlar remotamente a função do interruptor POWER.
G-1
RX-774P[U]SAFETY 98.3.10, 2:58 PM2
Caution: Proper Ventilation
To avoide risk of electric shock and fire and to protect from damage. Locate the apparatus as follows: Front: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. Top: No obstructions in 10 cm from the top. Back: No obstructions in 15 cm from the back Bottom: No obstructions, place on the level surface. In addition, maintain the best possible air circulation as illustrated.
Precaución: Ventilación Adecuada
Para evitar el riesgo de choque eléctrico e incendio y para proteger el aparato contra daños. Ubique el aparato de la siguiente manera: Frente: Espacio abierto sin obstrucciones Lados: 10 cm sin obstrucciones a los lados Parte superior: 10 cm sin obstrucciones en la parte superior Parte trasera: 15 cm sin obstrucciones en la parte trasera Fondo: Sin obstrucciones, colóquelo sobre una superficie
nivelada Además, mantenga la mejor circulación de aire posible como se ilustra.
Precaução: ventilação apropriada
Para prev enir o risco de choque elétrico ou incêndio e para proteger o aparelho contra danos. Localize-o da seguinte maneira: Frente: Espaço aberto, sem obstruções Lados: Espaço de 10 cm sem obstruções nos lados Topo: Espaço de 10 cm sem obstruções acima Atrás: Espaço de 15 cm sem obstruções atrás Parte inferior : Sem obstruções. Coloque o aparelho em superfície
nivelada. Mantenha, além disso, a maior circulação de ar possível, como indica a ilustração.
EnglishEspañolPortuguês
Wall or obstructions Pared u obstrucciones Parede ou obstáculo
Spacing 15 cm or more Espacio de 15 cm o más Espaço de 15 cm ou mais
RX-774PBK
Floor Piso Piso
Front Frente Frente
Stand height 15 cm or more Allura del soporte 15 cm o más Base com altura de 15 cm ou mais
G-2
Table of Contents
English
Parts Identification ...................................................................................... 3
Easy Set Up & Operations ............................................................................ 5
Getting Started........................................................................................... 9
Before Installation................................................................................................................................................................... 9
Checking the Supplied Accessories ........................................................................................................................................ 9
Setting the Voltage Selector Switch ........................................................................................................................................ 9
Connecting the FM and AM Antennas .................................................................................................................................10
Connecting the Speakers....................................................................................................................................................... 11
Connecting Audio/Video Components ................................................................................................................................. 14
Connecting the Power Cord .................................................................................................................................................. 19
Putting Batteries in the Remote Control ............................................................................................................................... 19
Basic Operations ....................................................................................... 20
Turning the Power On and Off (Standby) ............................................................................................................................. 20
Selecting the Source to Play ................................................................................................................................................. 20
Adjusting the Volume............................................................................................................................................................ 21
Selecting the Front Speakers................................................................................................................................................. 22
Muting the Sound.................................................................................................................................................................. 22
Recording a Source ............................................................................................................................................................... 22
Basic Settings........................................................................................... 23
Changing the Source Name .................................................................................................................................................. 23
Adjusting the Front Speaker Output Balance ....................................................................................................................... 23
Listening at Low Volume (Loudness) ................................................................................................................................... 23
Using the Sleep Timer........................................................................................................................................................... 24
Setting Center and Rear Speakers for DSP Modes............................................................................................................... 24
One Touch Operation .................................................................................. 26
About the One Touch Operation ........................................................................................................................................... 26
Using the One Touch Operation............................................................................................................................................ 26
Receiving Radio Broadcasts ........................................................................ 27
Setting the AM Tuner Interval Spacing ................................................................................................................................ 27
Tuning in Stations Manually................................................................................................................................................. 27
Using Preset Tuning.............................................................................................................................................................. 28
Selecting the FM Reception Mode ....................................................................................................................................... 29
Assigning Names to Preset Stations ..................................................................................................................................... 30
Using the SEA Modes ................................................................................ 31
Selecting Your Favorite SEA Mode ...................................................................................................................................... 31
Creating Your Own SEA Mode............................................................................................................................................. 32
1
Using the DSP Modes ................................................................................ 33
Using the 3D-PHONIC Modes ............................................................................................................................................. 34
Using the DAP Modes .......................................................................................................................................................... 36
Preparing for Surround Modes ............................................................................................................................................. 39
Using Surround Modes ......................................................................................................................................................... 43
Using the DVD MULTI Playback Mode .......................................................... 44
Speaker Arrangements for DVD MULTI Playback .............................................................................................................. 44
Activating the DVD MULTI Playback ................................................................................................................................. 44
Using the On-Screen Menus........................................................................ 47
Selecting the Source to Play ................................................................................................................................................. 47
Selecting the Different Sources for Picture and Sound ........................................................................................................ 47
Using the DSP Modes........................................................................................................................................................... 47
Adjusting the Front Speaker Output Balance ....................................................................................................................... 48
Listening at Low Volume (Loudness) ................................................................................................................................... 48
Adjusting the DSP Modes..................................................................................................................................................... 48
Selecting Your Favorite SEA Mode ...................................................................................................................................... 49
Creating Your Own SEA Mode............................................................................................................................................. 50
Setting the Center Speaker Size............................................................................................................................................ 50
Setting the Rear Speaker....................................................................................................................................................... 51
Setting the Delay Time ......................................................................................................................................................... 51
Operating the Tuner .............................................................................................................................................................. 51
Storing the Preset Stations .................................................................................................................................................... 52
Assigning Names to the Preset Stations ............................................................................................................................... 52
English
COMPU LINK Remote Control System ......................................................... 54
TEXT COMPU LINK Remote Control System................................................. 55
Showing the Disc Information on the TV Screen................................................................................................................. 56
Searching a Disc (Only for the CD player)........................................................................................................................... 57
Using the User File (Only for the CD Player with the User File Function) ......................................................................... 59
Entering the Disc Information .............................................................................................................................................. 60
Operating JVC’s Audio/Video Components ................................................... 62
Operating Other Manufactures’ Components ............................................... 65
Troubleshooting......................................................................................... 70
Specifications............................................................................................ 71
2
Parts Identification
Become familiar with the buttons and controls on the receiver before use.
English
1
23456
8
7
90
RX-774P AUDIO/VIDEO CONTROL RECEIVER
-
STANDBY
STANDBY/ON
POWER
_ ON OFF
PHONES
COMPULINK
Remote
ENHANCED COMPULINK CONTROL SYSTEM
=
SPEAKERS
12
~
!
DOLBY SURROUND
DSP MODE
SEA MODE
BALANCE/SURROUND
SEA ADJUST SETTING
ADJUST
#$%^&*(
@
Refer to the pages in parentheses for details.
Front Panel
1
STANDBY/ON button and STANDBY lamp (20)
2
Remote sensor (19)
3
DOLBY SURROUND button and lamp (41)
4
SEA MODE button (31) *
5
DVD MULTI/2CH button (20)
6
FM/AM TUNING button (27) *
7
FM MODE button (27, 29)
8
Display (20)
9
Source lamps (20)
0
MASTER VOLUME control (21)
-
POWER switch (19)
=
PHONES jack (22)
DVD MULTI/2CH
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECT LOUDNESS ONE TOUCH OPERATION
SOURCE NAME
MASTER VOLUME
CD
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
FM
AM
MULTI JOG
)
~
SPEAKERS 1/2 buttons and lamps (22)
!
DSP MODE button (34) *
@
BALANCE/SURROUND ADJUST button (23, 34) *
#
SEA ADJUST button (32) *
$
SETTING button (24) *
%
TUNER/SEA MEMORY button (28, 32)
^
SOUND SELECT button (21)
&
LOUDNESS/SOURCE NAME button (23)
*
ONE TOUCH OPERATION button and lamp (26)
(
TUNER PRESET button (27, 28) *
)
MULTI JOG control (23)
_
SOURCE SELECTOR control (20)
SOURCE SELECTOR
_
+
IMPORTANT:
To use the MULTI JOG control ()) on the front panel:
What this control actually does depends on which function you are trying to adjust. Before using this control, select the function by pressing one of the buttons marked with *.
3
English
+
¡
£ ¢ ∞
§
RM-SR774XU REMOTE CONTROL
TV/CATV
VCR
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
MUTE
TUNING DOWN
4 / REW
REC
TV/VIDEO
SET
O
N
PLAY
CONTROL
VCR TAPE
S
C
R
E
CHANNEL
STOP
TV VOLUME
E
C
N
AUDIO
SLEEP
CNTR
MENU
213
REAR (L)
546
(REAR R)
87/P9
+10
0
100+
TUNING UP
FF / ¢
PAUSE
EXIT
L
O
R
T
N
O
ª
º
Ÿ
¤
Refer to the pages in parentheses for details.
Remote Control
ª
+
TV/CATV/DBS and VCR buttons (65, 67)
¡
Source selecting buttons (21)
SEA MODE button (31)
£
SURROUND MODE button (35)
¢
SOUND CONTROL button (35, 38, 39, 46)
CD DISC button (63)
§
Remote control mode selector (AUDIO/TV/VCR, CATV/ DBS) (20)
MUTE button (22)
TUNING UP/TUNING DOWN buttons (27) Before using this control, make sure that you have pressed FM/AM button on the remote control.
IMPORTANT:
When using the remote control:
Check to see if its remote control mode selector (§) is set to the correct position.
To operate an audio system, TV, and VCR, set it to “AUDIO/TV/VCR.” To operate a CATV converter and DBS (Direct Broadcasting Satellite) tuner, set it to “CATV/DBS.”
SLEEP button (24)
º
AUDIO button (20)
10 keys for selecting preset channel (28) 10 keys for adjusting sound (35, 38, 39, 46) 10 keys for operating audio/video components (62, 65)
VOLUME buttons (+/–) (21)
Ÿ
CHANNEL buttons (+/–) (64)
Operating buttons for audio/video components (62, 65)
¤
MENU operation buttons (SET, EXIT, % , , @, #) (47)
4
Easy Set Up & Operations
If you are already familiar with audio components, following four pages just you opened give you enough information to operate your RX-774PBK for enjoyment of surround sound in your listening room.
English
TV
To video input
To S-video input
Center Speaker
Front Speaker
SOUND SELECTLOUDNESSONE TOUCH OPERATION
MASTER VOLUME
+
DVD
CD
TV SOUND/DBSPHONO
TAPE/MDVCR
FM
AM
SOURCE SELECTOR
MULTI JOG
FM/AM TUNNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOURCE NAME
RX-774PAUDIO/VIDEO CONTROL RECEIVER
STANDBY
DOLBY SURROUND
STANDBY/ON
POWER
_ ON OFF
DVD MULTI/2CH
SEA MODE
DSP MODE
SPEAKERS
BALANCE/SURROUND
PHONES
12
SEA ADJUST SETTING
ADJUST
COMPULINK
ENHANCED COMPULINK CONTROL SYSTEM
Remote
Front Speaker
Rear Speaker
GND
FM
AM
LOOP
GND
ANTENNA
FM
75 GND
WOOFER
AM EXT
Speaker Signal Cable
Subwoofer
Speaker Signal Cable
RX-774PBK
Rear Speaker
Speaker Signal Cable
AUDIO
LEFTRIGHT
PHONO
CD
OUT (REC)
TAPE
/MD
IN
(PLAY)
CENTER
SUB
DVD
SUBWOOFER
OUT
VIDEO S-VIDEO
LEFTRIGHT
DVD
TV SOUND
/DBS
OUT (REC)
VCR
IN
(PLAY)
MONITOR
OUT
TEXT
COMPU LINK
1 (MASTER UNIT) 2 (SLAVE UNIT)
COMPU LINK-3
(SYNCHRO)
1
2
Speaker Signal Cable
CENTER
SPEAKER
REAR
SPEAKERS
RIGHT LEFT
– –+ +
LEFTRIGHT FRONT SPEAKERS
230 – 240V
127V
220V
110V
1
LINE VOLTS
2
Speaker Signal Cable
5
To audio/video input
ANTENNA
IN OUT
To RF output
If your TV does not have a video input
VCR
IN
OUT
S-VIDEO
VIDEO AUDIO
L
AUDIO
R
To TV antenna input
To audio/video output
TV
English
8
CT
SU
MOD
AR
(L
6
2
NTR
STANDBY
STANDBY/ON
POWER
_ ON OFF
PHONES
COMPULINK
Remote
ENHANCED COMPULINK CONTROL SYSTEM
2
. Select the source.
AUDIO
SLEEP
RM-SR774XU REMOTE CONTROL
VCR
DVD
TAPE/MD FM/AMPHONO
SEA MODE
SURROUND
MODE
SOUND CONTROL
CNTR TONE
TEST
CD
DISC
AUDIO/TV
/VCR
CATV
VCR
EFFECT
BS
ENTER
DELAY
/P
10
TV/DBS
MENU
CNTR
213
REAR (L)
546
(REAR R)
9
87
+10
100+
0
FM MODE/MUTE
RETURN
VOLUME
CHANNEL
TV/CATV
/DBS
DVD
CD
RX-774P AUDIO/VIDEO CONTROL RECEIVER
DOLBY SURROUND
DSP MODE
SPEAKERS
12
TUNING UP
FF / ¢
BALANCE/SURROUND
DVD MULTI/2CH
SEA MODE
SEA ADJUST SETTING
ADJUST
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD TV/DBSVCR
DVD MULTI
TAPE/MD FM/AMPHONO
CD
SEA MODE
SURROUND
MODE
SOUND CONTROL
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECT LOUDNESS ONE TOUCH OPERATION
SOURCE NAME
AUDIO
SLEEP
CNTR TONE
ENTER
TEST
EFFECT
/P
DELAY
CD DISC
AUDIO/TV
/VCR
CATV
/DBS
CD
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
AM
SOURCE SELECTOR
MULTI JOG
MENU
CNTR
213
REAR (L)
546
(REAR R)
9
87
+10
100+
0
10
FM MODE/MUTE
RETURN
VOLUME
CHANNEL
TUNING UP
FF / ¢
MUTE
TUNING DOWN
4 / REW
PLAY
STOP
REC
CONTROL
TV/VIDEO
VCR TAPE
SET EXIT
FM
PAUSE
TV VOLUME
O
N
C
S
MASTER VOLUME
+
1
. Turn on the power.
AUDIO
SLEEP
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD TV/DBSVCR
DVD MULTI
TAPE/MD FM/AMPHONO
CD
CNTR TONE
SEA MODE
SURROUND
MODE
SOUND
CONTROL
CD DISC
3
. Adjust the volume.
EFFE
/P
SOUND
7
CONTROL
DELAY
CD
10
DISC
RETURN
AUDIO/TV
/VCR
CATV
/DBS
MUTE
TUNING DOWN
L
O
R
T
N
MENU
O
C
N
E
E
R
CNTR
213
REAR (L)
ENTER
546
TEST
EFFECT
/P
DELAY
10
RETURN
VOLUME
AUDIO/TV
/VCR
0
FM MODE/MUTE
VOLUME
CHANNEL
PLAY
4 / REW
REC
TV/VIDEO
SET EXIT
MENU
(REAR R)
87
0
FM MODE/MUTE
+10
100+
TUNING UP
FF / ¢
STOP
TV VOLUME
CONTROL
VCR TAPE
NNEL
PAUSE
9
+10
100+
L
O
R
T
N
MENU
O
C
4
. Select an appropriate
DSP mode.
CD
1
TEST
AUDIO/TV
/VCR
CATV
/DBS
EFFECT
ENTER
DELAY
/P
10
MUTE
RETURN
TUNING DOWN
RE
54
87
FM MODE/MUTE
VOLUME
4 / REW
(REAR R)
REC
0
CHANNEL
IDEO
9
+10
100+
TUNING UP
FF / ¢
PLAY
PAUSE
STOP
TV VOLUME
EXIT
TAPE
NTROL
C
SEA
MODE
SURROUND
MODE
SOUND
CONTROL
DISC
5
. DSP mode settings
are preset at the factory. However, if you need to make further adjustments, see pages 34 to 42.
SLEEP
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD TV/DBSVCR
DVD MULTI
TAPE/MD FM/AMPHONO
CD
CNTR TONE
SEA
MODE
TEST
SURROUND
MODE
SOUND
CONTROL
CD
DISC
AUDIO/TV
/VCR
CATV /DBS
AUDIO
MENU
CNTR
213
REAR (L)
ENTER
546
(REAR R)
87
EFFECT
/P
0
DELAY
10
FM MODE/MUTE
RETURN
VOLUME
CHANNEL
MUTE
TUNING DOWN
4 / REW
C
9
+10
100+
TUNING UP
FF / ¢
PLAY
PAUSE
STOP
TV VOLUME
6
Easy Set Up & Operations
For Reproducing DVD MULTI playback with your DVD player
English
TV
To video input
To S-video input
Center Speaker
Front Speaker
RX-774PAUDIO/VIDEO CONTROL RECEIVER
STANDBY
DOLBY SURROUND
STANDBY/ON
POWER
_ ON OFF
DVD MULTI/2CH
DSP MODE
SEA MODE
SPEAKERS
BALANCE/SURROUND
PHONES
12
SEA ADJUST SETTING
ADJUST
COMPULINK
ENHANCED COMPULINK CONTROL SYSTEM
Remote
FM/AM TUNNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECTLOUDNESSONE TOUCH OPERATION
MASTER VOLUME
DVD
CD
TV SOUND/DBSPHONO
TAPE/MDVCR
FM
AM
SOURCE SELECTOR
MULTI JOG
SOURCE NAME
+
Front Speaker
Rear Speaker
GND
ANTENNA
FM
GND
AM
LOOP
To front left/right channel audio output
FM
75
GND
SUB
WOOFER
AM EXT
AUDIO
LEFTRIGHT
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
SUBWOOFER
To rear left/right channel audio output
Speaker Signal Cable
Subwoofer
Speaker Signal Cable
RX-774PBK
Rear Speaker
Speaker Signal Cable
VIDEO S-VIDEO
LEFTRIGHT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
MONITOR
OUT
OUT
To center channel
TEXT
COMPU LINK
1 (MASTER UNIT) 2 (SLAVE UNIT)
COMPU LINK-3
(SYNCHRO)
1
2 2
To subwoofer audio output
REAR
CENTER
SPEAKERS
SPEAKER
RIGHT LEFT
– –+ +
RIGHT LEFT
FRONT SPEAKERS
Speaker Signal Cable
230 – 240V
127V
220V
110V
1
LINE VOLTS
Speaker Signal Cable
audio output
DVD player
To S-video output
7
ATTENUATOR 2CH
ON
OFF
To video output
RIGHT LEFTRIGHT LEFT
VIDEO OUT
VIDEO S-VIDEO
REARFRONT
RIGHT LEFT
AUDIO OUT
CENTER
SUBWOOFER
NORMAL
PCM/DOLBY DIGITAL
GAIN PLUS
AV COMPU LINKDIGITAL OUT
OPTICALCOAXIAL
1
English
8
CT
SU
MOD
D
MUL
PH
MEN
RX-774P AUDIO/VIDEO CONTROL RECEIVER
STANDBY
STANDBY/ON
POWER
_ ON OFF
PHONES
COMPULINK
Remote
ENHANCED COMPULINK CONTROL SYSTEM
2
. Select the source.
AUDIO
SLEEP
RM-SR774XU REMOTE CONTROL
VCR
DVD
CD
SEA MODE
SURROUND
MODE
SOUND
CONTROL
TAPE/MD FM/AMPHONO
CNTR TONE
TEST
EFFECT
CD DISC
AUDIO/TV
/VCR
CATV
/DBS
TV/DBSVCR
MENU
CNTR
213
REAR (L)
ENTER
546
(REAR R)
87
/P
0
DELAY
10
FM MODE/MUTE
RETURN
VOLUME
CHANNEL
UTE
TV/CATV
/DBS
DVD MULTI
SPEAKERS
12
9
+10
100+
TUNING UP
FF / ¢
AY
DOLBY SURROUND
DSP MODE
BALANCE/SURROUND
ADJUST
TV/CATV
/DBS
E
DVD MULTI/2CH
SEA MODE
SEA ADJUST SETTING
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECT LOUDNESS ONE TOUCH OPERATION
SOURCE NAME
AUDIO
VCR
SLEEP
RM-SR774XU REMOTE CONTROL
DVD TV/DBSVCR
DVD MULTI
TAPE/MD FM/AMPHONO
CD
CNTR TONE
SEA MODE
SURROUND
MODE
SOUND
CONTROL
CD DISC
TEST
EFFECT
AUDIO/TV
/VCR
CATV
/DBS
ENTER
DELAY
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
SOURCE SELECTOR
MULTI JOG
MENU
CNTR
213
REAR (L)
546
(REAR R)
9
87
0
FM MODE/MUTE
+10
100+
/P
10
RETURN
VOLUME
CHANNEL
TUNING UP
FF / ¢
MUTE
TUNING DOWN
4 / REW
PLAY
STOP
REC
CONTROL
TV/VIDEO
VCR TAPE
SET EXIT
CD
FM
AM
PAUSE
TV VOLUME
O
N
C
S
MASTER VOLUME
+
1
. Turn on the power.
AUDIO
SLEEP
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD TV/DBSVCR
DVD MULTI
TAPE/MD FM/AMPHONO
CD
CNTR TONE
SEA MODE
SURROUND
MODE
SOUND
CONTROL
CD DISC
3
. Adjust the volume.
EFFE
/P
SOUND
7
CONTROL
DELAY
CD
10
DISC
RETURN
AUDIO/TV /VCR
CATV
/DBS
MUTE
TUNING DOWN
L
O
R
T
N
MENU
O
C
N
E
E
R
CNTR
213
ENTER
546
TEST
EFFECT
/P
DELAY
10
RETURN
VOLUME
AUDIO/TV
/VCR
0
FM MODE/MUTE
VOLUME
CHANNEL
PLAY
4 / REW
REC
TV/VIDEO
SET EXIT
MENU
REAR (L)
(REAR R)
87
0
FM MODE/MUTE
+10
100+
TUNING UP
FF / ¢
STOP
CONTROL
VCR TAPE
9
+10
100+
NNEL
PAUSE
TV VOLUME
L
O
R
T
N
MENU
O
C
4
. DVD MULTI playback settings are preset at the
factory. However, if you need to make further adjustments, see pages 44 to 46.
DV
CD
SEA MODE
SURROUND
CONTROL
TAPE/MD
CNTR TONE
MODE
SOUND
213
ENTER
TEST
EFFECT
/P
DELAY
CD
10
DISC
RETURN
AUDIO/TV
/VCR
CATV
/DBS
MUTE
TUNING DOWN
CNTR
REAR (L)
546
(REAR R)
9
87
+10
100+
0
FM MODE/MUTE
VOLUME
CHANNEL
TUNING UP
FF / ¢
PLAY
PAUSE
STOP
4 / REW
TV VOLUME
REC
CONTROL
TV/VIDEO
VCR TAPE
SET EXIT
8
Getting Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.
English
Before Installation
General
Be sure your hands are dry.
Turn the power off to all components.
Read the manuals supplied with the components you are going to connect.
Locations
Install the receiver in a location that is level and protected from moisture.
The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F).
Make sure there is good ventilation around the receiver. Poor ventilation could cause
overheating and damage the receiver.
Handling the receiver
Do not insert any metal object into the receiver.
Do not disassemble the receiver or remove screws, covers, or cabinet.
Do not expose the receiver to rain or moisture.
Checking the Supplied Accessories
Check to be sure you have all of the following items, which are supplied with the receiver. The number in the parentheses indicates quantity of the pieces supplied.
Remote Control (1)
Batteries (2)
AM Loop Antenna (1)
FM Antenna (1)
Audio Signal Attenuating Cord (1)
AC Plug Adaptor (1) (except for Peoples’s Republic of China)
If anything is missing, contact your dealer immediately.
Setting the Voltage Selector Switch
Before connections, always do the following first if necessary.
How to set the voltage selector:
Set the correct voltage for your area with the voltage selector switch on the rear panel. Use a screw driver to rotate the switch so the number the arrow is pointing at is the same as the voltage where you are plugging in the receiver.
9
230 – 240V
127V
220V
110V
LINE VOLTS
Connecting the FM and AM Antennas
FM Antenna Connections
English
21
3
4
FM Antenna
GND
LOOP
FM
AM
ANTENNA
FM
75
GND
AM
EXT
Extend the FM wire antenna horizontally.
4
Outside FM Antenna Wire
1
2
20 mm
(13/16 in.)
3
10 mm
(7/16 in.)
How to strip the 75 coaxial cable and connect it to the FM
terminals
1. Strip back the outside covering of the 75 coaxial cable to expose the braided
metallic mesh about 20 mm (13/16 inches).
2. Pull the mesh back and twist it into a single connector as shown in the illustration
above.
3. Strip the insulation about 10 mm (7/16 inches) back from the central wire.
4. Insert the twisted mesh and the central wire to the FM terminals, as shown in the
illustration above.
Note:
If reception is poor, connect the outside antenna. Before attaching a 75Ω coaxial cable (the kind with a round wire going to an outside antenna), disconnect the supplied FM wire antenna.
AM Antenna Connections
ANTENNA
FM
75
GND
AM
EXT
1
AM Loop Antenna
2
GND
LOOP
FM
AM
Turn the loop until you have the best reception.
Notes:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.
Snap the tabs on the loop into the slots of the base to assemble the AM loop.
3
• If reception is poor, connect an outdoor single vinyl­covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)
Outdoor single vinyl­covered wire
10
Getting Started
English
Connecting the Speakers
You can connect the following speakers:
Two pairs of front speakers to produce normal stereo sound.
One pair of rear speakers to enjoy the surround effect.
One center speaker to produce more effective surround effect (to emphasize human voices).
One subwoofer to enhance the bass.
IMPORTANT:
After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible surround effect. For details, see page 24.
For each speaker (except for subwoofer), connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers. For connecting a subwoofer, see page 12.
Connecting the front speakers
Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect the front speakers to the FRONT SPEAKERS terminals by using the cables. You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).
1
+
2
RIGHT LEFT
Left Speaker Right Speaker
–+–
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.
1
2
FRONT SPEAKERS
1 Turn the knob
counterclockwise.
11
2 Insert the speaker
signal cable.
1
RIGHT
1
RIGHT
3 Turn the knob
clockwise.
1
RIGHT
Connecting the rear and center speakers
Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals by using the cables.
English
Center speaker
Left rear speaker
Right rear speaker
1 Open the terminal and then
insert the speaker signal cable.
CENTER
SPEAKER
SPEAKERS
RIGHT
REAR
LEFT
2 Close the terminal.
Connecting the subwoofer speaker
You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs.
SUBWOOFER
OUT
Powered subwoofer
12
Getting Started
English
About the speaker impedance
CASE 1 When you connect only one set of front speakers
Front
speaker
1
Front
speaker
1
CAUTION:
When connecting speakers, use speakers with the same SPEAKER IMPEDANCE indicated by the speaker terminals.
Note:
The required speaker impedance of the front speakers does differ depending on whether both the FRONT SPEAKERS 1 and FRONT SPEAKERS 2 terminals are used or only one of them is used.
Use front speakers with 4 — 16 ohm impedance.
CASE 2 When you connect two sets of front speakers
Front
speaker
2
Front
speaker
1
Front
speaker
2
Front
speaker
1
13
Use front speakers with 8 — 16 ohm impedance.
Connecting Audio/Video Components
F
English
You can connect the following audio/video components to this receiver using cables with RCA pin plugs (not supplied). Refer also to the manuals supplied with your components. If you want to connect a component not listed in the table below, refer to the manual supplied with it.
Audio Components Video Components
• Turntable • DVD (Digital Video Disc) player
• CD player • TV
• Cassette deck • DBS (Direct Broadcasting Satellite) tuner (or MD recorder) • VCR
Audio component connections
Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, and the red plug to the audio right jack.
Turntable
To audio output
CAUTION:
If you connect a sound­enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.
If an earth cable is provided for your turntable, connect the cable to the screw marked GND on the rear panel.
CD player
GND
RIGHT LEFT
AUDIO
PHONO
RIGHT LE
To audio output
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
SUBWOOFER
OUT
Cassette deck
or
MD recorder
To audio input To audio output
To audio output
To audio input
SUB
WOOFER
If your audio components have a COMPU LINK-3 or TEXT COMPU LINK terminal
See also page 54 for detailed information about the connection and the COMPU LINK-3 remote control system.
See also page 55 for detailed information about the connection and the TEXT COMPU LINK remote control system.
Notes:
• Any turntables incorporating a small-output cartridge such as an MC (moving-coil type) must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.
• You can connect either a cassette deck or an MD recorder to the TAPE/MD jacks. When connecting an MD recorder to the TAPE/MD jacks, change the source name, which will be shown on the display when selected as the source, to “MD.” See page 23 for details.
• When connecting an audio/ video component (ex.: Video CD player) with “karaoke” — singing along — function, use the audio signal attenuating cord supplied with this receiver. If not, sound may be distorted.
14
Getting Started
English
Video component connections
Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. If DVD player and TV have S-video (Y/C-separation) terminals, connect them using S­video cables (not supplied). Connecting these video components through the S-video input/output terminals will give you better picture playback quality.
IMPORTANT:
This receiver is equipped with both the composite video and S-video input terminals for the DVD player connection. You do not have to connect both the composite video and S-video terminals. However, remember that the video signals from the composite video input
terminal are output only through the composite video output terminals, while the ones from the S-video input terminal are output only through the S-video output terminal.
Therefore, if your DVD player is connected to the receiver only through the S­video input terminal, you cannot record the picture from the DVD player on the VCR. In addition, if the TV and the DVD player are connected to the receiver through the different video terminals, you cannot view the playback picture from the DVD player on the TV.
Note:
When connecting an audio/ video component (ex.: Video CD player) with “karaoke” — singing along — function, use the audio signal attenuating cord supplied with this receiver. If not, sound may be distorted.
TV connection (as the monitor)
GND
WOOFER
TV (or Monitor)
To composite video input
To S-video input (When the DVD player is connected using the S-video terminal)
SUB
RIGHT LEFT
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
RIGHT LEFT
SUBWOOFER
OUT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
MONITOR
OUT
VIDEO S-VIDEO
Note:
Use the video components of the PAL color system.
15
DVD player connection
When you connect the DVD player with stereo output jacks:
To S-video output (for better playback picture quality)
English
DVD player
To front left/right channel audio output
DVD
GND
To composite video
(or to audio mixed output if necessary)
RIGHT LEFT
AUDIO
PHONO
CD
RIGHT LEFT
DVD
TV SOUND
/DBS
VIDEO S-VIDEO
output
SUB
WOOFER
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
SUBWOOFER
OUT
OUT
(REC)
IN
(PLAY)
MONITOR
OUT
VCR
When you connect the DVD player with its analog discrete output (5.1 CH reproduction) jacks:
DVD player
DVD
GND
To composite video output
To center channel audio output
To subwoofer audio output
To rear left/right channel audio output
To S-video output (for better playback picture quality)
To front left/right channel audio output
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
RIGHT LEFT
SUBWOOFER
OUT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
MONITOR
OUT
VIDEO S-VIDEO
SUB
WOOFER
RIGHT LEFT
16
Getting Started
English
TV (as the sound source) or DBS tuner connection
You can connect either the TV or DBS tuner to the TV SOUND/DBS jacks.
TV
DBS tuner
GND
To audio output
GND
To audio output
DBS
SUB
WOOFER
SUB
WOOFER
RIGHT LEFT
RIGHT LEFT
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
RIGHT LEFT
SUBWOOFER
OUT
RIGHT LEFT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
MONITOR
OUT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
VIDEO S-VIDEO
VIDEO S-VIDEO
Note:
When connecting the TV to the TV SOUND/DBS jacks, DO NOT connect the TV’s video output to the video input terminal of the TV SOUND/DBS jacks.
Note:
When connecting the DBS tuner to the TV SOUND/DBS jacks, change the source name, which will be shown on the display when selected as the source, to “DBS.” See page 23 for details.
17
To video output
SUBWOOFER
OUT
MONITOR
OUT
VCR connection
English
VCR
VHS
To audio output
To video output
GND
To video input
To audio input
SUB
WOOFER
RIGHT LEFT
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
CENTER
DVD
RIGHT LEFT
SUBWOOFER
OUT
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
MONITOR
OUT
VIDEO S-VIDEO
18
Getting Started
English
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all connections have been made.
1. Plug the power cord into an AC outlet.
2. Press POWER to set it in the _ON position.
The STANDBY lamp lights up. A small amount of power
POWER
_ ON OFF
is always consumed.
To shut off the power completely
Press POWER to set it in the OFF position.
Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.
The difference between the POWER switch and the STANDBY/ON
The POWER switch is the mains supply switch, allowing the receiver to connect to the mains supply. To shut off the power completely, press the
POWER switch to set it in the OFF position.
The STANDBY/ON button is a functional on/off (standby) switch, and does not disconnect the receiver from the mains supply. A small amount of power is consumed even in standby mode for the receiver to accept signals from the remote control.
button
Notes:
• If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.
• The preset settings such as preset channel and sound adjustment may be erased in the following cases: – When you press
to set it in the position.
– When you unplug the power
cord.
– When a power failure
occurs.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.
POWER
OFF
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.
1. On the back of the remote control, remove the battery cover as illustrated.
2. Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (–) to (–).
3. Replace the cover.
R03 (UM-4)/AAA (24F)
-
+
+
-
If the range or effectiveness of the remote control decreases, replace the batteries. Use two R03 (UM-4)/AAA (24F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity indicated: (+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
19
Basic Operations
STANDBY
STANDBY/ON
STANDBY
STANDBY/ON
The following operations are commonly used when you play any sound source.
IMPORTANT:
When using the Remote Control, check to see if its remote control
AUDIO/TV
mode selector is set to the correct position:
/VCR
To operate an audio system, TV, and VCR, set it to “AUDIO/TV/
CATV
VCR.”
/DBS
To operate a CATV converter and DBS tuner, set it to “CATV/ DBS.”
Turning the Power On and Off (Standby)
On the front panel:
To turn on the power, press STANDBY/ON . The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.
Current source name appears
Current volume level is shown
VOLUME
100 1k 10k
To turn off the power (into standby mode), press STANDBY/ON again. The STANDBY lamp lights up.
here
Note:
Pressing the STANDBY/ON button again turns off the power (into standby mode) and lights the STANDBY lamp. A small amount of power is consumed in standby mode. To turn the power off completely, press the
POWER switch to set it in the
OFF position on the front
panel.
English
From the remote control:
To turn on the power, press AUDIO . The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.
To turn off the power (into standby mode), press AUDIO again. The STANDBY lamp lights up.
Selecting the Source to Play
On the front panel:
Turn SOURCE SELECTOR until the source name you want appears on the display.
As you turn the selector, the source changes as follows:
PHONOCD TAPE/MD AM
VCR
FM
DVD/DVD MULTITV SOUND/DBS
The selected source lamp also lights up.
VOLUME
Selected source name appears
CH–
CNTR
S E A
FR
100 1k 10k
THEATER DRAMA
D S P
3D-PHONC
LIVE CLUB ACTION DANCE CLUB HALL HEADPHONE PA VILION
MUTE AUTO
LOUDNESS
SLEEP
C
R
L
S
For selecting DVD MULTI playback mode as the source:
Press DVD MULTI/2CH so that “DVD MULTI” appears on the display. Each time you press the button, the DVD MULTI playback mode turns on and off, and the “DVD” and “DVD MULTI” alternately appears on the display.
Select “DVD” when you play back a disc in stereo or the audio output setting of the DVD player is mixed to two front channels.
Select “DVD MULTI” when you play back a disc on the DVD player with its analog discrete output mode (5.1 CH reproduction) selected. To enjoy the DVD MULTI playback mode, see page 44.
SOURCE SELECTOR
DVD
TV SOUND/DBS PHONO
Source lamps on the front panel
AUDIO
CD
TAPE/MDVCR
FM
AM
Note:
When connecting an MD recorder (to the TAPE/MD jacks), and a DBS tuner (to the TV SOUND/DBS jacks), change the source name appears on the display. See page 23 for details.
20
Basic Operations
English
From the remote control:
DVD MULTI
Press one of the source selecting buttons directly.
DVD MULTI Select the DVD player for viewing the
digital video disc using the analog discrete output mode (5.1CH reproduction) on the DVD player. Each time you press the button, the source alternates between “DVD” and “DVD MULTI.”
DVD Select the DVD player for viewing the stereo digital video disc player.
(“DVD MULTI” will be selected when the last mode for the DVD
playback has been the DVD MULTI playback mode.) VCR Select the video component connected to the VCR jacks. TV/DBS • Select the TV sound, when the remote control selector is set to
“AUDIO/TV/VCR.”
• Select the DBS tuner, when the remote control selector is set to “CATV/DBS.”
CD* Select the CD player. TAPE/MD* Select the cassette deck (or the MD recorder). PHONO* Select the turntable. FM/AM* Select an FM or AM broadcast.
Each time you press the button, the band alternates between FM and AM.
DVD TV/DBSVCR
CD TAPE/MD FM/AMPHONO
Note:
When you press one of the source selecting buttons marked above with an asterisk (*), the receiver automatically turns on.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to sound from another component.
On the front panel:
SOUND SELECT
1. Press SOUND SELECT briefly while viewing the picture from a video component such as the VCR or DVD player, etc. “SOUND SELECT” appears on the display.
SOURCE SELECTOR
2. Turn SOURCE SELECTOR to select the sounds (except the TV sound), while the indication of the above step is still on the display.
From the remote control:
Press one of the audio source selecting buttons (CD, TAPE/MD, PHONO, FM/AM), while viewing the picture from a video component such as the VCR or DVD player, etc.
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise.
When you turn MASTER VOLUME rapidly, the volume level also changes rapidly. When you turn MASTER VOLUME slowly, the volume level also changes slowly.
MASTER VOLUME
+
Notes:
• Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.
• When you select TV sound as the source, this function does not work.
CAUTION:
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
From the remote control:
To increase the volume, press VOLUME +. To decrease the volume, press VOLUME –.
21
VOLUME
+
The volume level can be adjusted within the range of “0” (minimum) to “90” (maximum).
Note:
Selecting the Front Speakers
SPEAKERS
12
English
On the front panel
only
:
When you have connected two pairs of the front speakers, you can select which to use.
Press SPEAKERS 1 or SPEAKERS 2 to select the speaker to use.
Each time you press the button, the lamp on the respective button turns on and off. When the lamp on either button lights up, the respective speakers are activated.
IMPORTANT:
You can activate two pairs of the front speakers at the same time only when no signals are sent to the center and rear speakers. Otherwise, activating one pair of the speakers deactivates the other.
Listening only with headphones
1. Connect a pair of headphones to the PHONES jack on the front panel.
2. Press SPEAKERS 1 and/or 2 so that no lamps on the buttons are turned on.
Muting the Sound
From the remote control
only
:
Press MUTE to mute the sound through all speakers and headphones connected.
“MUTE” appears on the display and the volume turns off (the volume level indicator goes off).
MUTE
Note:
If you use any of the DSP modes other than the 3D­PHONIC modes and “HEADPHONE” with both front speakers activated, the speakers connected to the FRONT SPEAKERS terminals are deactivated.
CAUTION:
Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
2
Note:
You cannot shut off the sound through the subwoofer using the SPEAKERS 1 and 2 buttons.
To restore the sound, press MUTE again so that “OFF” appears on the display. Turning MASTER VOLUME or pressing VOLUME +/– also restores the sound at the previous volume level.
Recording a Source
You can record any source playing through the receiver to a cassette deck (or a MD recorder) connected to the TAPE/MD jacks and the VCR connected to the VCR jacks at the same time. While recording, you can listen to the selected sound source at whatever sound level you like, without affecting the sound levels of the recording.
Note:
The output volume level, SEA and DSP modes cannot affect the recording.
IMPORTANT:
Before recording, turn off the DVD MULTI playback mode.
22
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.
English
IMPORTANT:
AUDIO/TV
When using the Remote Control, check to see if its remote control
/VCR
mode selector is set to the correct position:
CATV
To operate this receiver, set it to “AUDIO/TV/VCR (except when
/DBS
selecting the DBS tuner as the source).”
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel. Change the source name shown on the display when you select the MD recorder or DBS tuner as the source.
On the front panel
1. When changing the source name from “TAPE” to “MD”:
only
:
SOURCE SELECTOR
• Turn SOURCE SELECTOR until “TAPE” appears.
When changing the source name from “TV SOUND” to “DBS”:
• Turn SOURCE SELECTOR until “TV SOUND” appears.
2. Press and hold LOUDNESS/SOURCE NAME until
LOUDNESS
“ASSGN. MD” or “ASSGN. DBS” appears on the display.
SOURCE NAME
To change the source names to “TAPE” or “TV SOUND,” repeat the same procedure above (in step 1, select “MD” or “DBS” then press and hold SOURCE NAME).
Adjusting the Front Speaker Output Balance
If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.
On the front panel
1. Press BALANCE/SURROUND ADJUST repeatedly until “L/R BALANCE” appears on the display.
only
:
BALANCE/SURROUND
ADJUST
The display changes to show the current setting.
Note:
Without changing the source name, you can still use the connected components. However, there may be some inconvenience. – “TAPE” or “TV SOUND” will
appear on the display when you select the MD recorder or DBS tuner.
– You cannot use the COMPU
LINK remote control system (see page 54) to operate the MD recorder.
2. Turn MULTI JOG to adjust the balance, while the indication of the previous step is still on the display.
MULTI JOG
• Turning it clockwise decreases the left channel
output.
• Turning it counterclockwise decreases the right
channel output.
Listening at Low Volume (Loudness)
Human ears are not sensitive to bass at low volume. To compensate for this, the loudness function automatically boosts the bass level as you lower the volume.
On the front panel
Press LOUDNESS/SOURCE NAME briefly to select the
only
:
LOUDNESS
loudness function.
Each time you press the button, the loudness function alternates
SOURCE NAME
between “LOUDNESS ON” and “LOUDNESS OFF.”
Select “LOUDNESS ON” to activate the loudness function. The LOUDNESS indicator lights up on the display.
Select “LOUDNESS OFF” to cancel it. The indicator goes off.
23
Note:
The loudness function affects the front speaker sounds only.
Using the Sleep Timer
Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than play all night.
English
From the remote control
Press SLEEP repeatedly.
only
:
SLEEP
The shut-off time on the display changes as follows, and the SLEEP indicator lights up on the display.
SLEEP 20min.SLEEP 10min. SLEEP 30min.
SLEEP 00min.
(Canceled)
SLEEP 90min.
SLEEP 40min.
SLEEP 50min.
SLEEP 80min. SLEEP 70min. SLEEP 60min.
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining until the shut-off time
Press SLEEP once. The remaining time until the shut-off time appears in minutes.
To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 00min.” appears on the display. (The SLEEP indicator goes off.) Turning off the power also cancels the Sleep Timer.
Setting Center and Rear Speakers for DSP Modes
To obtain the best possible surround sound of the DSP modes, you have to register the information about the speakers arrangement after all connections are completed.
Center Speaker Setting
Register the center speaker size.
On the front panel
1. Press SETTING repeatedly until “CENTER SPK”
only
:
SETTING
(Center Speaker Size) appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the appropriate item about your center speaker, while the indication of the
MULTI JOG
previous step is still on the display.
As you turn it, the display changes to show the following:
LARGE SMALL NONE
LARGE: Select this mode when the size of the center speaker is the same as
that of the front speakers.
SMALL: Select this mode when the size of the center speaker is smaller than
that of the front speakers.
NONE: Select this mode when you do not use a center speaker.
Note:
When you change your speakers, you need to register the information about the speakers again.
24
Basic Settings
English
Rear Speaker Setting
Register whether you have connected the rear speakers or not.
On the front panel
1. Press SETTING repeatedly until “REAR SPK” (Rear Speaker) appears on the display.
The display changes to show the current setting.
only
:
SETTING
Note:
When you change your speakers, you need to register the information about the speakers again.
2. Turn MULTI JOG to register whether you have
MULTI JOG
connected the rear speaker or not, while the indication of the previous step is still on the display.
As you turn it, the rear speaker setting alternates between “YES” and “NO.”
YES: Select this mode when you use rear speakers. NO: Select this mode when you do not use rear speakers.
Delay Time Setting
Register the delay time of the sound from the rear speakers, comparing the sound from the front speakers.
On the front panel:
1. Press SETTING repeatedly until “DELAY TIME” appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the delay time of the rear speaker output, while the indication of the previous step is still on the display.
As you turn it, the delay time changes as follows:
SETTING
MULTI JOG
DELAY 15msec
DELAY 20msec
DELAY 30msec
As the distance from you to your rear speakers decreases, you will get the better surround sound by using smaller delay time.
From the remote control:
1. Press SOUND CONTROL.
2. Press DELAY repeatedly until an appropriate delay time appears on the display.
Each time you press the button, the delay time changes as follows:
DELAY 15msec
DELAY 20msec
DELAY 30msec
25
SOUND
CONTROL
DELAY
10
RETURN
One Touch Operation
This receiver can memorize the optimum sound settings for each playing source.
About the One Touch Operation
English
JVC’s One Touch Operation function is used to assign and store different sound settings for each different playing source. By using this function, you don’t have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled.
The following can be stored for each source:
Volume level (see page 21)
Balance (see page 23)
Loudness (see page 23)
SEA modes (see page 31)
DSP modes – 3D-PHONIC mode settings (see page 34) – DAP mode settings (see page 36) – Surround mode settings (see page 39)
DVD MULTI playback mode settings (see page 44)
Using the One Touch Operation
On the front panel
To store the sound settings
1. Press ONE TOUCH OPERATION.
The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled.
only
:
ONE TOUCH OPERATION
Notes:
• If the source is FM or AM, you can assign a different setting for each band.
• The DSP modes and DVD MULTI playback mode cannot be used at the same time.
2. Adjust the sound using the functions listed above.
The newly adjusted settings are memorized.
To recall the sound settings
With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source is recalled, when the source is selected.
To cancel the One Touch Operation function
Press ONE TOUCH OPERATION so that the lamp goes off. (Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)
ONE TOUCH OPERATION
26
Receiving Radio Broadcasts
STANDBY
STANDBY/ON
STANDBY
STANDBY/ON
FM/AM TUNING
You can browse through all the stations or use the preset function to go immediately to a particular station.
English
IMPORTANT:
AUDIO/TV
When using the Remote Control, check to see if its remote control
/VCR
mode selector is set to the correct position:
CATV
To operate this receiver, set it to “AUDIO/TV/VCR (except when
/DBS
selecting the DBS tuner as the source).”
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. When shipped, the spacing is set to 9 kHz.
On the front panel
only
:
To select the 10 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet and POWER is pressed to set it in the _ON position. Hold down TUNER PRESET and press STANDBY/ON . “10K STEP” appears on the display for about three seconds. Now the 10 kHz interval is selected.
To change back to the 9 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet and POWER is pressed to set it in the _ON position. Hold down FM MODE and press STANDBY/ON . “9K STEP” appears on the display for about three seconds. Now the 9 kHz interval is selected.
Tuning in Stations Manually
On the front panel:
1. Press FM/AM TUNING to select the band.
Each time you press the button, the band alternates between FM and AM.
2. Turn MULTI JOG until you find the frequency you want.
• Turning it clockwise increases the frequency.
• Turning it counterclockwise decreases the frequency.
From the remote control:
1. Press FM/AM to select the band.
Each time you press the button, the band alternates between FM and AM.
TUNER PRESET
FM MODE
and
and
MULTI JOG
FM/AM
Notes:
• When you turn MULTI JOG quickly or hold TUNING DOWN or TUNING UP in step 2, the frequency keeps changing until a station is tuned in.
• When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display. When an FM stereo program is received, the STEREO indicator also lights up.
2. Press TUNING DOWN or TUNING UP repeatedly until you find the frequency you want.
27
D
G
N
I
N
U
T
4 / REW
N
W
O
G
N
I
N
U
T
FF / ¢
P
U
or
Using Preset Tuning
English
Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 40 stations at random.
To store the preset stations
On the front panel
only
:
1. Tune in the station you want to preset (see page 27).
If you want to store the FM reception mode for this station, select the FM reception mode you want. See page 29 for details.
TUNER/SEA MEMORY
2. Press TUNER/SEA MEMORY.
“CH-” appears and the channel number position starts flashing on the display for about 5 seconds.
MULTI JOG
3. Turn MULTI JOG to select a channel number while the channel number position is flashing.
4. Press TUNER/SEA MEMORY again while the selected channel number is flashing on the display.
TUNER/SEA MEMORY
The selected channel number stops flashing. The station is assigned to the selected channel number.
5. Repeat steps 1 to 4 until you store all the stations you want.
Note:
You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure that they are activated for tuner, not for the CD and others. (See page 62.)
To erase a stored preset station
Storing a new station on a used number erases the previously stored one.
To tune in a preset station
On the front panel:
1. Press TUNER PRESET .
2. Turn MULTI JOG to select a preset channel.
From the remote control:
1. Press FM/AM.
Each time you press the button, the band alternates between FM and AM.
2. Press 10 keys to select a preset channel number.
• For channel number 5, press 5.
• For channel number 15, press +10 then 5.
• For channel number 20, press +10 then 10.
• For channel number 30, press +10, +10, then 10.
TUNER PRESET
MULTI JOG
FM/AM
213
TEST
ENTER
546
EFFECT
87/P9
DELAY
10
0
FM MODE/MUTE
RETURN
CNTRCNTR TONE
REAR (L)
(REAR R)
+10
100+
MENU
Note:
When you use the 10 keys on the remote control, be sure that they are activated for tuner, not for the CD and others. (See page 62.)
28
FM MODE
Receiving Radio Broadcasts
English
Selecting the FM Reception Mode
On the front panel:
When an FM stereo broadcast is hard to receive or noisy, set the FM reception mode to MONO. (When shipped from the factory, this mode has been set to AUTO.) You can change the FM reception mode while receiving an FM broadcast.
Press FM MODE to select the FM reception mode.
Each time you press the button, the FM reception mode alternates between AUTO and MONO.
AUTO: When a program is broadcasted in stereo, you will hear stereo
sound; when in monaural, you will hear monaural sounds. This mode is also useful to suppress static noise between stations. The MUTE AUTO indicator lights up on the display.
MONO: Reception will be improved although you will lose the stereo effect.
In this mode, you will hear noise while tuning into the stations. The MUTE AUTO indicator goes off on the display.
From the remote control:
Press FM MODE/MUTE to select the FM reception mode.
Each time you press the button, the FM reception mode alternates between AUTO and MONO.
0
FM MODE/MUTE
Note:
You can store the FM reception mode for each preset station.
Note:
When using the FM MODE/ MUTE button, be sure that the 10 keys are activated for tuner, not for the CD and others. (See page 62.)
29
Assigning Names to Preset Stations
You can assign a name of up to four characters to each preset station. When a preset station is tuned in, its assigned name will appear on the display.
English
On the front panel
only
:
1. Tune in a preset station.
See page 28 for details.
2. Press TUNER/SEA MEMORY.
The preset channel number starts flashing for about 5 seconds.
3. Press TUNER PRESET, while the preset channel number is flashing.
The first character position starts flashing.
CH–
4. Turn MULTI JOG to select a character, while the first character position is flashing.
You can use characters listed below.
CH–
5. Press TUNER PRESET, while a character you want is flashing.
The next (or previous) character position starts flashing.
TUNER/SEA MEMORY
TUNER PRESET
MULTI JOG
TUNER PRESET
Note:
If you turn MULTI JOG while the preset channel number is flashing, you can change the preset channel number.
Note on step 3 to 7:
You cannot select any entry after the indication on the display stops flashing. In this case, repeat the procedure from step 2 again.
CH–
6. Repeat steps 4 and 5 to enter up to four characters.
7. Press TUNER/SEA MEMORY while the last selected character is flashing after you have assigned a name.
To erase the input characters
Insert spaces using the same procedure described above.
Available characters
Space
CBADEGFHIJKLMNO
SRQTUWVX
87695
MULTI JOG
Z01234P
Y
TUNER/SEA MEMORY
30
Using the SEA Modes
The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.
English
IMPORTANT:
AUDIO/TV
When using the Remote Control, check to see if its remote control
/VCR
mode selector is set to the correct position:
CATV
To operate this receiver, set it to “AUDIO/TV/VCR (except when
/DBS
selecting the DBS tuner as the source).”
Selecting Your Favorite SEA Mode
On the front panel:
1. Press SEA MODE.
The display changes to show the current setting.
2. Turn MULTI JOG until the mode you want appears on the display, while the indication of the previous step is still on the display.
As you turn it, the SEA mode changes as follows:
SEA ROCK SEA MUSICAL SEA MOVIE
SEA USERMODESEA OFF
SEA ROCK: Gives a heavy sound. Both high and low frequencies are
boosted.
SEA MUSICAL: Enhance the mid-frequency range, which the human
voice is mostly made up of.
SEA MOVIE: Adds breadth to sounds so you feel like you are in a
movie theater.
SEA COUNTRY: Enhances the high-frequency range so that instruments
such the violin and banjo are emphasized.
SEA JAZZ: Gives a feeling of a live atmosphere. Good for acoustic
music.
SEA USERMODE: Your original SEA adjustment (see page 32). SEA OFF: No SEA mode is applied (see below).
SEA COUNTRY
SEA JAZZ
SEA MODE
MULTI JOG
Notes:
• The SEA modes cannot be used for recording.
• When the SEA mode is turned on, the SEA indicator lights up on the display.
To cancel the SEA mode
Turn MULTI JOG until “SEA OFF” appears in step 2 above. The SEA indicator goes off from the display.
From the remote control:
Press SEA MODE repeatedly until the SEA mode you want appears on the display.
Each time you press the button, the SEA mode changes as follows:
SEA ROCK SEA MUSICAL SEA MOVIE
SEA USERMODESEA OFF
To cancel the SEA mode
Press SEA MODE repeatedly until “SEA OFF” appears. The SEA indicator goes off from the display.
31
SEA COUNTRY
SEA JAZZ
SEA
MODE
Note:
When the SEA mode is turned on, the SEA indicator lights up on the display.
Creating Your Own SEA Mode
You can adjust and store your own SEA adjustment into memory (SEA USERMODE).
English
On the front panel
only
:
If you do not want to store your adjustment, but rather want to adjust the SEA temporarily, skip step 4 below.
1. Press SEA ADJUST repeatedly until the frequency
SEA ADJUST
range (100Hz, 1kHz or 10kHz) you want appears on the display.
S E A
FR
100 1k 10k
S E A
FR
100 1k 10k
2. Turn MULTI JOG to adjust the SEA level of the
VOLUME
VOLUME
MULTI JOG
selected frequency range, while the indication of the previous step is still on the display.
• Turning it clockwise increases the level.
• Turning it counterclockwise decreases the level.
This FR means this adjustment can be applied to the FRont speakers only.
S E A
100 1k 10k
FR
3. Repeat step 1 and 2 to adjust other frequency ranges if necessary.
4. Press TUNER/SEA MEMORY, while the indication
TUNER/SEA MEMORY
of the previous step is still on the display.
Your adjustment is stored into SEA USERMODE.
To recall your own SEA adjustment
See page 31.
To erase a stored adjustment
Storing a new adjustment into SEA USERMODE erases the previously stored one.
32
Using the DSP Modes
The built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D­PHONIC mode, DAP (Digital Acoustic Processor) mode and Surround mode (Dolby Pro Logic and Theater
English
Surround.)
On 3D-PHONIC mode
The 3D-PHONIC mode gives you such a nearly surround effect as it is reproduced through the Dolby Surround decoder, which is widely used to reproduce sounds with a feeling of movement like those experienced in movie theaters. The 3D-PHONIC mode is the result of research on sound localization technology carried out at JVC for many years and makes it possible to reproduce the surround sound with only two front speakers.
On the DAP mode
The sound heard in a concert hall or club consists of direct sound and indirect sound — early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delayed by the distances of the ceiling and walls. These direct sounds and indirect sounds are the most important elements of the acoustic surround effects. The DAP mode can create these important elements, and gives you a real “being there” feeling.
Early reflections
Direct sounds
Reflections from behind
Notes:
• The DSP modes has no effect on monaural sources.
• You can not use the two types of the DSP modes at the same time.
• The DSP modes cannot be used for recording.
• When you select “DVD MULTI” as the source to play, you cannot select or adjust the DSP modes.
IMPORTANT:
Before recording, turn off the DVD MULTI playback mode.
On Surround mode
With this receiver, you can use two types of the surround mode.
Dolby Pro Logic
Dolby Pro Logic has been developed to reproduce the important elements of the acoustic surround at home. To watch the soundtracks of video software bearing the mark includes the same encoded surround information as found in Dolby Stereo films, the receiver can provide you with Dolby Pro Logic.
JVC’s Theater Surround
In order to reproduce a more realistic sound field in your listening room while playing soundtracks of video software bearing the mark has been designed to give you clearer vocals and to create a real “being there” feeling.
DOLBY SURROUND
* which
DOLBY SURROUND
, JVC’s Theater Surround
* Manufactured under license
from Dolby Laboratories Licensing Corporation. “Dolby,” the double-D symbol, and “Pro Logic” are trademarks of Dolby Laboratories Licensing Corporation.
As for the DVD MULTI Playback Mode, see pages 44 to
46.
33
IMPORTANT:
AUDIO/TV /VCR
CATV /DBS
When using the Remote Control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/VCR (except when selecting the DBS tuner as the source).”
Using the 3D-PHONIC Modes
English
When using JVC’s 3D-PHONIC modes, you need only two front speakers to reproduce the soundtracks of video software bearing the mark
DOLBY SURROUND
. The 3D-PHONIC modes give you a very realistic surround effect as if the sound is reproduced through the Dolby Pro Logic decoder.
On the front panel:
1. Press DSP MODE.
The current DSP mode appears on the display.
2. Turn MULTI JOG until the mode (3D ACTION, 3D
DRAMA, or 3D THEATER) you want appears on the display, while the indication of the previous step is still on the display.
The 3D-PHONIC, DSP and PRO LOGIC indicators also light up on the display. As you turn it, the DSP modes change as follows (the indicator of the DSP mode also lights up on the display):
LIVE CLUBTHEATER
DANCE CLUB
DSP OFF
3D THEATER
3D DRAMA
3D ACTION
HEADPHONE
DSP MODE
MULTI JOG
HALL
PAVILION
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the 3D­PHONIC modes.
• The 3D-PHONIC mode is not used with the other DSP modes such as the Dolby Pro Logic and the DAP mode. When the 3D-PHONIC mode is turned on, the other DSP mode, if used, will be turned off.
3D ACTION: Best for action and war movies — where the action is fast and
explosive.
3D DRAMA: Best for dramas and romantic movies — where the action is
slow and soft.
3D THEA TER: Reproduces the sound field of a large theater. DSP OFF
:
No DSP mode is applied.
For the other modes, see pages 36 and 39.
If you need to make any adjustment, go to the following steps.
3. Press BALANCE/SURROUND ADJUST repeatedly
BALANCE/SURROUND
until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
4. Turn MULTI JOG to select the effect level, while the indication of the previous step is still on the display.
As you turn it, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 4
DSP EFFECT 3
As the number increases, the selected 3D-PHONIC mode becomes stronger.
ADJUST
MULTI JOG
34
Using the DSP Modes
English
5. Select and play a sound source which was processed with Dolby Surround and is labeled with
DOLBY SURROUND
mark.
To cancel the 3D-PHONIC mode
Turn MULTI JOG until “DSP OFF” appears in step 2. The 3D-PHONIC, DSP and PRO LOGIC indicators go off from the display.
From the remote control:
1. Press SURROUND MODE repeatedly until the mode (3D ACTION, 3D DRAMA, or 3D THEATER) you want appears on the display.
The 3D-PHONIC, DSP and PRO LOGIC indicators also light up on the display. Each time you press the button, the DSP modes change as follows (the indicator of the DSP mode also lights up on the display):
PRO LOGIC
OFF
3D THEATER
3D DRAMA
2. Press SOUND CONTROL.
10 keys are activated for sound adjustments.
LIVE CLUBTHEATER
3D ACTION
DANCE CLUB
HEADPHONE
HALL
SURROUND
MODE
PAVILION
SOUND
CONTROL
Note:
Once you have adjusted the effect level, it is memorized for each 3D-PHONIC mode.
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the 3D-PHONIC modes.
• The 3D-PHONIC mode is not used with the other DSP modes such as the Dolby Pro Logic and the DAP mode. When the 3D-PHONIC mode is turned on, the other DSP mode, if used, will be turned off.
3. Press EFFECT to select the effect level.
Each time you press the button, the effect level changes
EFFECT
7
/P
as follows:
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 4
DSP EFFECT 3
As the number increases, the selected 3D-PHONIC mode becomes stronger.
4. Select and play a sound source which was processed with Dolby Surround and is labeled with
DOLBY SURROUND
mark.
To cancel the 3D-PHONIC mode
Press SURROUND MODE repeatedly until “OFF” appears. The 3D-PHONIC, DSP, and PRO LOGIC indicators go off from the display.
Note:
Once you have adjusted the effect level, it is memorized for each 3D-PHONIC mode.
35
Using the DAP Modes
English
You can use five DAP modes — “Live Club, Dance Club, Hall, Pavilion, and Headphones.”
Among the DAP modes, “Headphones” is very special. It can create the same stereo sound as you listen through the speakers off air while listening to a source using headphones. So, you can feel as if you were not using the headphones and listening to music in a room.
On the front panel:
1. Press DSP MODE.
The current DSP mode appears on the display.
2. Turn MULTI JOG until the mode (LIVE CLUB, DANCE CLUB, HALL, PAVILION, or HEADPHONE) you want appears on the display, while the indication of the previous step is still on the display.
The DSP indicator also lights up on the display. As you turn it, the DSP modes change as follows (the indicator of the selected DSP mode also lights up on the display):
LIVE CLUBTHEATER
DANCE CLUB
DSP MODE
MULTI JOG
HALL
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the DAP modes.
• The DAP mode is not used with the other DSP modes such as the Dolby Pro Logic and 3D-PHONIC mode. When the DAP mode is turned on, the other DSP mode, if used, will be turned off.
DSP OFF
3D THEATER
3D DRAMA
3D ACTION
HEADPHONE
LIVE CLUB: Gives the feeling of a live music club with a low ceiling. DANCE CLUB: Gives a throbbing bass beat. HALL: Gives clear vocal and the feeling of a concert hall. PAVILION: Gives the spacious feeling of a pavilion with a high ceiling. HEADPHONE: DSP OFF
:
Gives a spacious stereo effect when listening with headphones. No DSP mode is applied.
For the other modes, see pages 34 and 39.
If you need to make any adjustment, go to the following steps.
3. Press BALANCE/SURROUND ADJUST repeatedly
BALANCE/SURROUND
until “REAR LEVEL” appears on the display.
The display changes to show the current setting.
4. Turn MULTI JOG to adjust the rear speaker output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
PAVILION
ADJUST
MULTI JOG
Note:
When you select “HEADPHONE” (the HEADPHONE indicator lights up), you cannot go to the following steps. No adjustments can be made for “HEADPHONE.”
Notes:
• You cannot adjust the left and right rear speaker output level separately.
• You cannot adjust the rear speaker level when “REAR SPK” is set to “NO” (see page
25).
Continued to the next page.
36
Using the DSP Modes
English
5. Press BALANCE/SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
6. Turn MULTI JOG to select the effect level, while the indication of the previous step is still on the display.
As you turn it, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
As the number increases, the selected DAP mode becomes stronger.
DSP EFFECT 4
DSP EFFECT 3
To cancel the DAP mode
Turn MULTI JOG until “DSP OFF” appears in step 2. The DSP indicator goes off from the display.
BALANCE/SURROUND
ADJUST
MULTI JOG
Note:
Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.
37
From the remote control:
1. Press SURROUND MODE repeatedly until the mode you want appears on the display.
The DSP indicator also lights up on the display. Each time you press the button, the DSP modes change as follows (the indicator of the selected DSP mode also lights up on the display):
PRO LOGIC
OFF
LIVE CLUBTHEATER
DANCE CLUB
SURROUND
MODE
HALL
PAVILION
English
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the DAP modes.
• The DAP mode is not used with the other DSP modes such as the Dolby Pro Logic and 3D-PHONIC mode. When the DAP mode is turned on, the other DSP mode, if used, will be turned off.
3D THEATER
3D DRAMA
3D ACTION
If you need to make any adjustment, go to the following steps.
2. Press SOUND CONTROL.
10 keys are activated for sound adjustments.
3. Press REAR•(L) +/– to adjust the rear speaker output level.
• Pressing REAR•(L) – decreases the output level up to
–10 dB.
• Pressing REAR•(L) + increases the output level up to
+10 dB.
4. Press EFFECT to select the effect level.
Each time you press the button, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 4
DSP EFFECT 3
As the number increases, the selected DAP mode becomes stronger.
HEADPHONE
SOUND
CONTROL
ENTER
REAR (L)
56
EFFECT
7
/P
Note:
When you select “HEADPHONE” (the HEADPHONE indicator lights up), you cannot go to the following steps. No adjustments can be made for “HEADPHONE.”
Notes:
• You cannot adjust the left and right rear speaker output level separately.
• You cannot adjust the rear speaker level when “REAR SPK” is set to “NO” (see page
25).
To cancel the DAP mode
Press SURROUND MODE repeatedly until “OFF” appears. The DSP indicator goes off from the display.
Note:
Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.
38
Using the DSP Modes
English
Preparing for Surround Modes
The receiver memorizes two types of Surround modes adjustments; one for Dolby Pro Logic and the other for Theater Surround. To do the adjustment procedure, use the remote control.
From the remote control:
1. Press SURROUND MODE until “PRO LOGIC” or “THEATER” appears on the display.
When “PRO LOGIC” is selected, the PRO LOGIC indicator also lights up on the display.
When “THEATER” is selected, the PRO LOGIC, DSP and THEATER indicators also light up on the display. Each time you press the button, the DSP modes change as follows:
PRO LOGIC
LIVE CLUBTHEATER
DANCE CLUB
OFF
3D THEATER
3D DRAMA
3D ACTION
HEADPHONE
PRO LOGIC: Select this mode to watch a video source with Dolby Surround. THEATER: Select this mode to watch a video source with Dolby Surround.
This is JVC original surround mode and gives you the feeling of a movie theater.
OFF: No DSP mode is applied.
SURROUND
MODE
HALL
PAVILION
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the Surround modes.
• The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off.
For the other modes, see pages 34 and 36.
If you need to make any adjustment, go to the following steps.
2. Press SOUND CONTROL.
10 keys are activated for sound adjustments.
3. Press TEST to start checking the speaker output balance.
“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:
TEST TONE L TEST TONE C TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE S
(Rear speakers)
C
L R
S
The speaker indicators also light on the display while the test tone comes out of the speakers. L: Lights when the test tone comes out of the left front speaker. C: Lights when the test tone comes out of the center speaker. R: Lights when the test tone comes out of the right front speaker. S: Lights when the test tone comes out of the rear speakers.
SOUND
CONTROL
TEST
4
Notes:
• No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 24).
• No test tone comes out of the rear speakers when “REAR SPK” is set to “NO” (see page
25).
39
4. If necessary, adjust the speaker output level as
CNTR
23
MENU
follows:
• To adjust the center speaker output level, press CNTR +/–.
• To adjust the rear speaker output level, press REAR•(L) +/–.
Pressing – decreases the output level up to –10 dB. Pressing + increases the output level up to +10 dB.
5. Press TEST again to stop the test tone.
6. Press CNTR TONE to select the center tone level you want.
The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of. Each time you press the button, the display changes as follows:
SHARP1 SHARP2FLATSOFT2 SOFT1
Adjusted level are also shown on the equalizer display.
This CNTR means this adjustment can be applied to the center speaker only.
S E A
CNTR
(Example: When “FLAT” is selected.)
REAR (L)
ENTER
56
TEST
4
CNTR TONE
1
English
Notes:
• You can adjust the speaker output levels and center tone without outputting the test tone.
• You cannot adjust the left and right rear speaker output level separately.
• You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 24).
• You cannot adjust the rear speaker level when “REAR SPK” is set to “NO” (see page
25).
Note:
The center tone cannot be adjusted when “CENTER SPK” is set to “NONE” (see page 24).
100 1k 10k
To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much). To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much).
When “FLAT” is selected, no adjustment is applied.
If you have selected Theater Surround, go to the following steps.
7. Press EFFECT to select the effect level.
Each time you press the button, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 4
DSP EFFECT 3
As the number increases, the surround effect becomes stronger.
EFFECT
7
/P
Note:
When you have selected Dolby Pro Logic, you cannot select the effect level.
Note:
Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.
40
Using the DSP Modes
English
On the front panel:
You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.
1. For Dolby Pro Logic: Press DOLBY SURROUND so that the lamp on the button lights up and “PRO LOGIC” appears on the display.
The PRO LOGIC indicator also lights up. Each time you press the button, the Dolby Pro Logic mode turns on and off.
DOLBY SURROUND
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the Surround modes.
• The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off.
For Theater Surround:
1) Press DSP MODE.
The current DSP mode appears on the display.
2) Turn MULTI JOG until “THEATER” appears on the display, while the indication of the previous step is still on the display.
The PRO LOGIC, DSP and THEATER indicators also light up on the display. As you turn it, the DSP modes change as follows:
LIVE CLUBTHEATER
DANCE CLUB
DSP OFF
3D THEATER
3D DRAMA
3D ACTION
If you need to make any adjustment, go to the following steps.
2. If necessary, adjust the center speaker output level as follows.
1) Press BALANCE/SURROUND ADJUST
repeatedly until “CENTER LEVEL” appears on the display.
The display changes to show the current setting.
2) Turn MULTI JOG to adjust the center speaker
output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
DSP MODE
MULTI JOG
HALL
PAVILION
HEADPHONE
BALANCE/SURROUND
ADJUST
MULTI JOG
Note:
You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 24).
3. If necessary, adjust the rear speaker output level as follows.
1) Press BALANCE/SURROUND ADJUST
repeatedly until “REAR LEVEL” appears on the display.
The display changes to show the current setting.
2) Turn MULTI JOG to adjust the rear speaker
output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
41
Notes:
• You cannot adjust the left and right rear speaker output level separately.
• You cannot adjust the rear speaker level when “REAR SPK” is set to “NO” (see page
25).
English
4. Press BALANCE/SURROUND ADJUST repeatedly until “CENTER TONE” appears on the display.
The display changes to show the current setting.
5. Turn MULTI JOG to select the center tone level you want, while the indication of the previous step is still on the display.
As you turn it, the display changes to show the following:
SHARP1 SHARP2FLATSOFT2 SOFT1
If you have selected Theater Surround, go to the following steps.
6. Press BALANCE/SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
7. Turn MULTI JOG to select the effect level, while the indication of the previous step is still on the display.
As you turn it, the effect level changes as follows:
BALANCE/SURROUND
ADJUST
MULTI JOG
BALANCE/SURROUND
ADJUST
MULTI JOG
Note:
The center tone cannot be adjusted when “CENTER SPK” is set to “NONE” (see page 24).
Note:
When you have selected Dolby Pro Logic, you cannot select the effect level.
DSP EFFECT 1 DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 4
DSP EFFECT 3
As the number increases, the surround effect becomes stronger.
Note:
Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.
42
DSP MODE
Using the DSP Modes
English
Using Surround Modes
Once you have finished adjustments for Dolby Pro Logic and Theater Surround, you can use the same adjustments every time you want to use these modes.
On the front panel:
1. For Dolby Pro Logic: Press DOLBY SURROUND so that the lamp on the button lights up and “PRO LOGIC” appears on the display.
The PRO LOGIC indicator also lights up. Each time you press the button, the Dolby Pro Logic mode turns on and off.
For Theater Surround:
1) Press DSP MODE.
The current DSP mode appears on the display.
2) Turn MULTI JOG until “THEATER” appears on
the display, while the indication of the previous step is still on the display.
The PRO LOGIC, DSP and THEATER indicators also light up on the display.
2. Select and play a sound source which was processed with Dolby Surround and is labeled with
DOLBY SURROUND
mark.
DOLBY SURROUND
MULTI JOG
Notes:
• When you select “DVD MULTI” as the source to play, you cannot select the Surround modes.
• The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off.
To cancel the Surround mode
For Dolby Pro Logic: Press DOLBY SURROUND again so that “SURROUND OFF” appears on the display.
For Theater Surround: Press DSP MODE, then turn MULTI JOG until “DSP OFF” appears on the display.
From the remote control:
1. Press SURROUND MODE repeatedly until “PRO LOGIC” or “THEATER” appears on the display.
When “PRO LOGIC” is selected, the PRO LOGIC indicator also lights up on the display.
When “THEATER” is selected, the PRO LOGIC, DSP and THEATER indicators also light up on the display.
2. Select and play a sound source which was processed with Dolby Surround and is labeled with
DOLBY SURROUND
mark.
To cancel the surround mode
Press SURROUND MODE repeatedly until “OFF” appears.
SOUND
CONTROL
43
Using the DVD MULTI Playback Mode
DVD MULTI/2CH
This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Before playing back a DVD, refer also to the manual supplied with the DVD player.
Speaker Arrangements for DVD MULTI Playback
The following illustrations show how to obtain the optimum sound environment for the DVD MULTI playback mode. Try to find the speaker direction and location to create the optimum sound field.
When you play back a disc on the DVD player with its analog discrete output mode selected:
English
Left front
speaker
Left
rear
speaker
Sub-
woofer
TV
Center speaker
Right front
speaker
Right
rear
speaker
Activating the DVD MULTI Playback
You can adjust the DVD MULTI playback mode while playing back a DVD using the analog discrete output mode on the DVD player. Once you made adjustments, the receiver memorizes the adjustments until you change them. You also need to set the DVD player to the analog discrete output mode.
Note:
You can place the subwoofer anywhere around you.
On the front panel:
1. Press DVD MULTI/2CH so that “DVD MULTI”
2. Select the analog discrete output mode on the DVD
If you need to make any adjustment, go to the following steps.
3. Press BALANCE/SURROUND ADJUST repeatedly
appears on the display.
player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
until “CENTER LEVEL” appears on the display.
The display changes to show the current setting.
BALANCE/SURROUND
ADJUST
Continued to the next page.
Note:
When you select “DVD MULTI” as the source to play, the DSP modes are canceled temporarily.
Note:
You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 24).
44
Using the DVD MULTI Playback Mode
English
4. Turn MULTI JOG to adjust the center speaker output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
5. Press BALANCE/SURROUND ADJUST repeatedly until “REAR L LEVEL” appears on the display.
The display changes to show the current setting.
6. Turn MULTI JOG to adjust the left rear speaker output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
7. Press BALANCE/SURROUND ADJUST repeatedly until “REAR R LEVEL” appears on the display.
The display changes to show the current setting.
8. Turn MULTI JOG to adjust the right rear speaker output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.
MULTI JOG
BALANCE/SURROUND
ADJUST
MULTI JOG
BALANCE/SURROUND
ADJUST
MULTI JOG
Note:
You cannot adjust the left rear speaker level when “REAR SPK” is set to “NO” (see page 25).
Note:
You cannot adjust the right rear speaker level when “REAR SPK” is set to “NO” (see page 25).
9. Press BALANCE/SURROUND ADJUST repeatedly
BALANCE/SURROUND
until “CENTER TONE” appears on the display.
The display changes to show the current setting.
10.Turn MULTI JOG to select the center tone level, while the indication of the previous step is still on the display.
The center tone level affects the mid-frequency range, which the human voice is mostly made up of. As you turn it, the display changes to show the following:
SHARP1 SHARP2FLATSOFT2 SOFT1
To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much). To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much).
When “FLAT” is selected, no adjustment is applied.
ADJUST
MULTI JOG
Note:
The center tone cannot be adjusted when “CENTER SPK” is set to “NONE” (see page 24).
45
IMPORTANT:
CNTR
23
MENU
(REAR R)
89
AUDIO/TV
When using the Remote Control, check to see if its remote control
/VCR
mode selector is set to the correct position:
CATV
To operate this receiver, set it to “AUDIO/TV/VCR (except when
/DBS
selecting the DBS tuner as the source).”
From the remote control:
1. Press DVD MULTI so that “DVD MULTI” appears on the display.
Each time you press the button, the source alternates between “DVD” and “DVD MULTI.”
2. Select the analog discrete output mode on the DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following steps.
English
DVD MULTI
3. Press SOUND CONTROL.
10 keys are activated for adjusting the sound.
4. Press CNTR +/– to adjust the center speaker output level.
• Pressing CNTR – decreases the output level up to
–10 dB.
• Pressing CNTR + increases the output level up to
+10 dB.
5. Press REAR•(L) +/– to adjust the left rear speaker output level.
• Pressing REAR•(L) – decreases the output level up to
–10 dB.
• Pressing REAR•(L) + increases the output level up to
+10 dB.
6. Press (REAR•R) +/– to adjust the right rear speaker output level.
• Pressing (REAR•R) – decreases the output level up to
–10 dB.
• Pressing (REAR•R) + increases the output level up to
+10 dB.
SOUND
CONTROL
REAR (L)
ENTER
56
Note:
You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 24).
Note:
You cannot adjust the left rear speaker level when “REAR SPK” is set to “NO” (see page 25).
Note:
You cannot adjust the right rear speaker level when “REAR SPK” is set to “NO” (see page 25).
7. Press CENTER TONE to select the center tone level.
Each time you press the button, the display changes to show the following:
To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much). To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much).
When “FLAT” is selected, no adjustment is applied.
CNTR TONE
1
Note:
The center tone cannot be adjusted when “CENTER SPK” is set to “NONE” (see page 24).
SHARP1 SHARP2FLATSOFT2 SOFT1
46
Using the On-Screen Menus
You can use the Menus on the TV screen to control the receiver. To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page
English
15), and set the TV’s input mode to the proper position to which the receiver is connected.
Selecting the Source to Play (Also see page 20)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
MAIN MENU
Shows the buttons you can use on the current menu. In this case, use % / to move down, and @ / # to select, adjust or set the item.
2. Press ON SCREEN CONTROL % / to move to “SOURCE.”
3. Press ON SCREEN CONTROL @ / # to select the source.
4. When you finish, press EXIT.
The menu disappears from the TV.
up and
Selecting the Different Sources for Picture and Sound
You can view the pictures played back on a video component while listening to any source.
Notes:
• If your TV is not of the PAL color system, the TV screen will be distorted.
• The on-screen display will disappear if no operation is done for about 1 minute.
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “VISUAL.”
3. Press ON SCREEN CONTROL @ / # to select a different video source.
• When you select “OSD,” see page 56.
4. When you finish, press EXIT.
The menu disappears from the TV.
Using the DSP Modes (Also see pages 34, 36, and 39)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “MODE.”
3. Press ON SCREEN CONTROL @ / # to select the DSP mode you want to use.
4. When you finish, press EXIT.
The menu disappears from the TV.
MAIN MENU
MAIN MENU
47
Adjusting the Front Speaker Output Balance (Also see page 23)
English
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears on the TV.
3. Press ON SCREEN CONTROL % / to move to “BAL.” (Balance).
4. Press ON SCREEN CONTROL @ / # to adjust the balance.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Listening at Low Volume (Loudness) (Also see page 23)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears on the TV.
MAIN MENU
SOUND CONTROL menu
SOUND CONTROL menu
3. Press ON SCREEN CONTROL % / to move to “LOUDNESS.”
4. Press ON SCREEN CONTROL @ / # to turn the loudness “ON” or “OFF.”
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Adjusting the DSP Modes (Also see pages 34, 36, and 39)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “MODE.”
3. Press ON SCREEN CONTROL @ / # to select the DSP mode you want to adjust.
4. Press ON SCREEN CONTROL % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
5. Press ON SCREEN CONTROL % / to move to “SURROUND LEVEL,” then press @ / #.
The SURROUND LEVEL menu appears.
SOUND CONTROL menu
Note:
Continued to the next page.
If you select “HEADPHONE” in step 3, the SURROUND LEVEL menu will not appear.
48
Using the On-Screen Menus
English
6. Press ON SCREEN CONTROL % / to move to the item you want to set or adjust, then press ON SCREEN CONTROL @ / #.
On these adjustment menus, you can do the following:
For 3D-PHONIC modes:
“DSP EFFECT”: Select the effect level.
For DAP modes (LIVE CLUB, DANCE CLUB, HALL, PAVILION):
“REAR LEVEL”: Adjust the rear speaker output level. * “DSP EFFECT”: Select the effect level.
For Dolby Pro Logic surround mode:
“TEST TONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output level. ** “REAR LEVEL”: Adjust the rear speaker output level. * “CENTER TONE”: Select the center tone level. **
For Theater surround mode:
“TEST TONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output level. ** “REAR LEVEL”: Adjust the rear speaker output level. * “CENTER TONE”: Select the center tone level. ** “DSP EFFECT”: Select the effect level. *
Example: SURROUND LEVEL menu for Theater surround
Notes:
* Not displayed when “REAR
SPK” is set to “NO” (see page
25).
**Not displayed when
“CENTER SPK” is set to “NONE” (see page 24).
For DVD MULTI playback mode:
“CENTER LEVEL”: Adjust the center speaker output level. “REAR L LEVEL”: Adjust the left rear speaker output level. “REAR R LEVEL”: Adjust the right rear speaker output level. “CENTER TONE”: Select the center tone level.
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Selecting Your Favorite SEA Mode (Also see page 31)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press ON SCREEN CONTROL % / to move to “SEA,” then press @ / #.
The SEA menu appears.
4. Press ON SCREEN CONTROL % / to move to “SEA MODE.”
5. Press ON SCREEN CONTROL @ / # to select the SEA mode you want.
MAIN MENU
SOUND CONTROL menu
6. When you finish, press EXIT repeatedly until the menu disappears from the TV.
49
SEA menu
Creating Your Own SEA Mode (Also see page 32)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
English
MAIN MENU
3. Press ON SCREEN CONTROL % / to move to “SEA,” then press @ / #.
The SEA menu appears.
4. Press ON SCREEN CONTROL % / to move to “SEA ADJUST,” then press @ / #.
The SEA ADJUST menu appears.
5. Press ON SCREEN CONTROL % / / @ / # to adjust the SEA mode as you want.
@ / # : Select the frequency ranges. % / fi : Adjust the frequency levels.
6. Press SET to store the setting into the SEA USERMODE.
• If you press EXIT, without pressing SET in this step, you can return to the SEA
menu. (The adjustment you have made is active but not stored.)
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Setting the Center Speaker Size (Also see page 24)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
SOUND CONTROL menu
SEA menu
SEA ADJUST menu
2. Press ON SCREEN CONTROL % / to move to “SETTING,” then press @ / #.
The SETTING menu appears.
3. Press ON SCREEN CONTROL % / to move to “CENTER SPK” (Center Speaker Size).
4. Press ON SCREEN CONTROL @ / # repeatedly until the appropriate center speaker size is selected.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
SETTING menu
50
Using the On-Screen Menus
English
Setting the Rear Speaker (Also see page 25)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SETTING,” then press @ / #.
The SETTING menu appears.
3. Press ON SCREEN CONTROL % / to move to “REAR SPK” (Rear Speaker).
4. Press ON SCREEN CONTROL @ / # to set your rear speakers.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Setting the Delay Time (Also see page 25)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SETTING,” then press @ / #.
The SETTING menu appears.
MAIN MENU
SETTING menu
SETTING menu
3. Press ON SCREEN CONTROL % / to move to “DELAY TIME.”
4. Press ON SCREEN CONTROL @ / # to set the delay time of the rear speaker sound.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Operating the Tuner
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Press ON SCREEN CONTROL % / to move to the item you want to set or adjust, then press ON SCREEN CONTROL @ / #.
On the TUNER CONTROL menu, you can do the following: “PRESET CH”: Select a preset channel station. (See page 28) “BAND”: Select the band. (See page 27) “FREQUENCY”: Tune in a station manually. (See page 27) “FM MODE”: Select the FM reception mode. (See page 29) * “PRESET MEMORY”: See “Storing the Preset Stations” on the next page.
MAIN MENU
TUNER CONTROL menu
4. When you finish, press EXIT repeatedly until the menu disappears from the TV.
51
Note:
* Not displayed when an AM
station is selected.
Storing the Preset Stations (Also see page 28)
English
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Tune into a station on the TUNER CONTROL menu, referring to “Operating the T uner”.
4. Press ON SCREEN CONTROL % / to move to “PRESET MEMORY,” then press @ / #.
The PRESET MEMORY menu appears.
5. Press ON SCREEN CONTROL % / to move to “PRESET CH.”
6. Press ON SCREEN CONTROL @ / # to select a preset station number you want.
7. Press SET to store the setting.
8. When you finish, press EXIT repeatedly until the menu disappears from the TV.
MAIN MENU
TUNER CONTROL menu
PRESET MEMORY menu
Assigning Names to the Preset Stations (Also see page 30)
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Press ON SCREEN CONTROL % / to move to “PRESET CH.”
4. Press ON SCREEN CONTROL @ / # to select a preset station.
5. Press ON SCREEN CONTROL % / to move to “PRESET MEMORY,” then press @ / #.
The PRESET MEMORY menu appears.
6. Press ON SCREEN CONTROL % / to move to “PRESET NAME,” then press SET.
The character entry screen appears.
Continued to the next page.
MAIN MENU
TUNER CONTROL menu
PRESET MEMORY menu
52
Using the On-Screen Menus
English
7. Press ON SCREEN CONTROL % / / @ / # to move in front of a character you want.
You can also select the following: SPACE: To enter space CANCEL: To erase the character
: To go back to the previous character position or go to the next character
position
8. Press SET to enter the selected character.
9. Repeat steps 7 and 8 to enter up to four characters.
10.Press ON SCREEN CONTROL % / / @ / # to move to “PRESET NAME,” then press SET to store the setting.
The TUNER CONTROL menu appears again.
11.When you finish, press EXIT repeatedly until the menu disappears from the TV.
PRESET MEMORY menu: Character entry screen
53
COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver.
To use this remote control system, you need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see below) in addition to the connections using cables with RCA pin plugs (see page 14).
Make sure that the AC power cords of these components are unplugged before connection. Plug the AC power cords only after all connections are complete.
COMPU LINK – 3
(SYNCHRO)
CD player
Cassette deck
or
MD recorder
Turntable
This remote control system allows you to use four functions listed below.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote sensor on the receiver using this remote control. Aim the remote control directly at the remote sensor on the receiver. For details, see pages 62 and 63.
Notes:
• If your audio component has two COMPU LINK-3 (SYNCHRO) jacks, you can use either one. If it has only one COMPU LINK-3 (SYNCHRO) jack, connect it so that it is the last item in the series of components. (For example, the turntable or CD player in the diagram to the left.)
• To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 23.)
• Refer also to the manuals supplied with your audio components.
English
Automatic Source Selection
When you press the play (
33
3) button on a connected component or on its own remote
33
control, the receiver automatically turns on and changes the source to the component. On the other hand, if you select a new source on the receiver or the remote control, the selected component begins playing immediately. In both cases, the previously selected source continues playing without sound for a few seconds.
Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 connection
Both the CD player and cassette deck (or MD recorder) turn on and off (standby) along with the receiver. When you turn on the receiver, the CD player or cassette deck (or MD recorder) will turn on automatically, depending on which component has been previously selected. When you turn off the receiver, both the CD player and cassette deck (or MD recorder) will turn off (standby).
Synchronized Recording
Synchronized recording means the cassette deck (or MD recorder) starts recording as soon as a CD or a record begins playing.
To use synchronized recording, follow these steps:
1. Put a tape in the cassette deck (or an MD in the MD recorder), and a disc in the CD player (or a record on the turntable).
2. Press the record (
¶¶
) button and the pause (
¶¶
88
8) button on the cassette deck (or
88
MD recorder) at the same time.
This puts the cassette deck (or MD recorder) into recording pause. If you do not press the record () button and pause (8) button at the same time, the synchronized recording feature will not operate.
3. Press the play (
33
3) button on the CD player or on the turntable.
33
The source changes on the receiver, and as soon as play starts, the cassette deck (or MD recorder) starts recording. When the play ends, the cassette deck (or MD recorder) enters recording pause, and stops about 4 seconds later.
Notes:
• During synchronized recording, the selected source cannot be changed.
• If your CD player is playing in program mode, a 4-second blank is recorded between tracks so that the music scan feature of your cassette deck can be used on the recorded tape.
• If the power of any component is shut off during synchronized recording, the COMPU LINK remote control system may not operate properly. In this case, you must start again from the beginning.
54
TEXT COMPU LINK Remote Control System
The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD Text* and MDs. Using these information in the discs, you can operate the CD player or
English
MD recorder equipped with the TEXT COMPU LINK remote control system through the receiver.
CONNECTIONS:
To use this remote control system, you need to connect the CD player and/or MD recorder you want to operate, following the procedures below.
1. If you have already plugged your CD player, MD recorder, and this receiver into the AC outlets, unplug their AC power cords first.
2. Connect your CD player, MD recorder, and this receiver as follows, through the COMPU LINK-3 (SYNCHRO) jacks and TEXT COMPU LINK jacks.
1) COMPU LINK-3 (SYNCHRO) jacks: Use the cables with the monaural mini-
plugs (not supplied with this receiver)
CD player
MD recorder
2) TEXT COMPU LINK jacks: Use the cables with the stereo mini-plugs (not
supplied with this receiver)
CD player
MD recorder
IMPORTANT:
Set the Master/Slave Selector on the rear to “1(MASTER UNIT).”
• “2(SLAVE UNIT)” is just for the serviceman’s use. The TEXT COMPU LINK remote control system does not function with the selector set to “2(SLAVE UNIT).”
3. Connect your CD player, MD recorder and this receiver, using the cables with RCA pin plugs (see page 14).
COMPU LINK – 3
(SYNCHRO)
TEXT
COMPU LINK
1(MASTER UNIT) 2(SLAVE UNIT)
*What is a CD Text?
In a CD Text, some information about the disc (its disc title, performer, composer, arranger, etc.) is recorded.
Notes:
• If your audio component has two COMPU LINK-3 (SYNCHRO) jacks, you can use either one. If it has only one COMPU LINK-3 (SYNCHRO) jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)
• If your audio component has two TEXT COMPU LINK jacks, you can use either one. If it has only one TEXT COMPU LINK jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)
• Refer also to the manuals supplied with your CD player or MD recorder.
4. Plug the AC power cords of these components above into the AC outlets.
5. When turning on these components for the first time, turn on the connected components first, then turn on this receiver.
FUNCTIONS:
This remote control system allows you to use the functions listed below.
Displaying the Disc Information on the TV screen
Disc information such as its performer and disc title (and track titles only when a CD Text is selected) is shown on the TV screen.
Disc Search: Only for CD Player
This remote control system can allow you to search discs by the performer, disc title, and music genre. With this disc search, you can easily find the disc you want to play.
Additional Functions:
If your CD player has the User File function, you can select a disc from the groups. * A “user file” is a group of the discs you make as you like on the CD player.
If your CD player has the disc memory function, you can input the performer, disc title, and music genre about these normal audio CDs on the TV screen.
Note:
If you turn on the receiver before turning on the other components after connecting components, the TEXT COMPU LINK remote control system does not work correctly. If this happens:
1. Turn off the all components including this receiver.
2. Turn on the connected components.
3. Turn on this receiver.
55
English
OPERATIONS
To use this remote control system, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 15), and set the TV’s input mode to the proper position to which the receiver is connected. Make sure you have connected the CD
player or MD recorder equipped with the TEXT COMPU LINK remote control system. If not, you cannot use the following functions.
Showing the Disc Information on the TV Screen
1. Press any button of ON SCREEN CONTROL % / / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL % / to move to “SOURCE.”
3. Press ON SCREEN CONTROL @ / # to select “CD” or “MD.”
4. Press ON SCREEN CONTROL % / to move to “VISUAL.”
5. Press ON SCREEN CONTROL @ / # to select “OSD,” then press EXIT.
The Disc Information screen appears on the TV.
Notes:
• The on-screen display will not
appear about one minute after the power is turned on.
• The on-screen display will
disappear in the following case: – if no operation is done for
about 10 minutes.
– if you do any operation
other than explained in this section.
• T o control the MD recorder
using the TEXT COMPU LINK remote control system, you have to change the source name shown on the display from “TAPE” to “MD.” (See page 23.)
• The number of characters to
show the disc information such as the disc title or track title is limited to 32. So if the disc title, for example, is longer than 32 characters, only the first 32 characters are shown.
• Some special characters such
as accented letters cannot be displayed correctly.
1 Source name: CD or MD 2 Select 3 Track numbers and track titles.
• The current playing (selected) track is indicated in yellow.
• When you move
4 Select this (move
(see page 57).
5 Select this (move in front), then press SET to go to the USER FILE screen (see
page 59).
6 Select this (move
page 60).
7 Disc information such as the disc title, performer, and music genre.
When this is selected ( @ / #. Each time you press the button, disc information (see the note) changes.
8 Select or , then press SET to change the track. 9 Usable buttons and their functions for the current selection.
Indication here will be changed what is currently selected ( in front) on the screen.
or , then press SET to change the disc.
to a track number, you can change the track information by pressing @ / #. Each time you press the button, track information alternates between its track title and its performer. (You can also start playing the track by pressing SET.)
in front), then press SET to go to the DISC SEARCH screen
in front), then press SET to go to the TITLE INPUT screen (see
in front) , you can change the disc information by pressing
6. When you finish, press EXIT repeatedly until the MAIN MENU appears on the TV.
To exit from the MAIN MENU:
1) Press ON SCREEN CONTROL % / to move to “VISUAL.”
2) Press ON SCREEN CONTROL @ / # to select any one other than “OSD,” then press EXIT.
Note on 7:
The following information will appear on the display:
• Disc title
• Performer
• Genre
• Song writer
• Composer
• Arranger
• Message Only recorded information will
be shown. If there is no data, “NO DATA” will appear.
Note on 9:
For example, the SET button will be used to start play (PLAY), to go to the next screen (ENTER), and to determine the selection (ENTER).
56
TEXT COMPU LINK Remote Control System
English
Searching a Disc (Only for the CD player)
Search a disc by its performer:
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “SEARCH,” then press SET.
The DISC SEARCH screen appears on the TV.
3. Press ON SCREEN CONTROL % / to move to “PERFORMER”, then press SET.
The PERFORMER SEARCH screen appears.
4. Press ON SCREEN CONTROL % / / @ / # to move in front of the first character of the performer you want to search, then press SET.
To correct the incorrect entry, press ON SCREEN CONTR OL % / to mo ve
in front of the correct character, then press SET. To erase the incorrect entry, press ON SCREEN CONTROL % / to move to
CANCEL, then press SET.
5. Press SET again.
Disc search starts, then the SEARCH RESULT screen, showing the performers, appears.
6. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press ON SCREEN
CONTROL % / to move to a searched disc, then press @ / #. Each time you press @ / #, the disc information alternates between its performer an its disc title.
Going to the Disc Information screen (see page 56): Press ON SCREEN
CONTROL % / to move to a searched disc, then press SET.
Showing unseen disc information (if more than 5 discs are listed as a result of
the search): Press ON SCREEN CONTROL % / to move to (or ), then press SET.
Going back to the PERFORMER SEARCH screen: Press EXIT.
DISC SEARCH screen
PERFORMER SEARCH screen
SEARCH RESULT screen
Note:
Symbols such as @, # or $ cannot be available for search.
Search a disc by its disc title:
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “SEARCH,” then press SET.
The DISC SEARCH screen appears on the TV.
3. Press ON SCREEN CONTROL % / to move to “DISC TITLE”, then press SET.
The DISC TITLE SEARCH screen appears.
4. Press ON SCREEN CONTROL % / / @ / # to move in front of the first character of the disc title you want to search, then press SET.
To correct the incorrect entry, press ON SCREEN CONTROL % / move in
front of the correct character, then press SET. To erase the incorrect entry, press ON SCREEN CONTROL % / move to
CANCEL, then press SET.
57
DISC SEARCH screen
DISC TITLE SEARCH screen
5. Press SET again.
Disc search starts, then the SEARCH RESULT screen, showing the disc titles, appears.
6. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press ON SCREEN
CONTROL % / to move to a searched disc, then press @ / #. Each time you press @ / #, the disc information alternates between its disc title and its performer.
Going to the Disc Information screen (see page 56): Press ON SCREEN
CONTROL % / to move to a searched disc, then press SET.
Showing unseen disc information (if more than 5 discs are listed as a result of
the search): Press ON SCREEN CONTROL % / to move to (or ), then press SET.
Going back to the DISC TITLE SEARCH screen: Press EXIT.
Search a disc by its genre:
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “SEARCH,” then press SET.
The DISC SEARCH screen appears on the TV.
English
SEARCH RESULT screen
Note:
Symbols such as @, # or $ cannot be available for search.
3. Press ON SCREEN CONTROL % / to move to “GENRE”, then press SET.
The GENRE SEARCH screen appears.
4. Press ON SCREEN CONTROL % / to move to the genre you want to search, then press SET.
To show the unseen genres, press ON SCREEN CONTROL % / until they appear.
Disc search starts, then the SEARCH RESULT screen, showing the disc titles, appears.
5. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press ON SCREEN
CONTROL % / to move to a searched disc, then press @ / #. Each time you press @ / #, the disc information alternates between its disc title and its performer.
Going to the Disc Information screen (see page 56): Press ON SCREEN
CONTROL % / to move to a searched disc, then press SET.
Showing unseen disc information (if more than 5 discs are listed as a result of
the search): Press ON SCREEN CONTROL % / to move to (or ), then press SET.
Going back to the GENRE SEARCH screen: Press EXIT.
GENRE SEARCH screen
SEARCH RESULT screen
58
TEXT COMPU LINK Remote Control System
English
Using the User File (Only for the CD Player with the User File Function)
You can use the User File function through this receiver. For the User File function, refer to the manual supplied with your CD player.
Using your own User Files:
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “USER FILE,” then press SET.
The USER FILE screen appears on the TV. To show the unseen user files, press ON SCREEN CONTROL % / until they
appear.
3. Press ON SCREEN CONTROL % / to move to the User File you want, then press SET.
The selected User File screen appears on the TV. The disc information shown will be the disc title. (If no disc title information is recorded for the discs, only the disc numbers will be shown.)
4. On this selected User File screen, you can do the following:
Changing the indication of the disc information: Press ON SCREEN
CONTROL % / to move to a disc, then press @ / #. Each time you press @ / #, the disc information alternates between its disc title and its performer.
Starting a disc play: Press ON SCREEN CONTROL % / to move to a disc,
then press SET.
Showing unseen disc information (if more than 5 discs are listed): Press ON
SCREEN CONTROL % / to move to (or ) and press SET.
Going back to the USER FILE screen: Press EXIT.
USER FILE screen
User File 1 screen
59
Entering the Disc Information

For the CD Player with the disc memory function:
You can use the disc memory function through this receiver. The disc information (its performer, disc title, and its music genre) of normal audio CDs will be stored into the memory built in the CD player. For the disc memory function, refer to the manual supplied with your CD player.
The performer, disc title, and music genre information are usually recorded in a CD Text. However, if a CD Text has no genre information recorded in the disc itself, you can input its music genre by yourself. Note: You can enter the TITLE INPUT screens for a CD Text and input its titles. Howev er, you cannot store the titles you have input for a CD Text.
Example: Entering the following information for Disc 1
Performer: “MICHEAL” Disc title: “MY FAVORITE”
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “TITLE INPUT,” then press SET.
The TITLE INPUT: PERFORMER screen appears on the TV.
English
TITLE INPUT: PERFORMER screen
3. Press ON SCREEN CONTROL % / / @ / # to move in front of a character you want, then press SET to enter the character.
If the current CD is a CD Text, go to step 5 without entering the performer. To use the lower case letters, press ON SCREEN CONTROL % / / @ / # to
move to
SHIFT
, then press SET.
To use the upper case letters again, press ON SCREEN CONTROL % / / @ / # to move to
SHIFT
, then press SET.
4. Repeat step 3 until you finish putting a name (up to 32 characters) to this User File.
To insert a space, press ON SCREEN CONTROL % / / @ / # to move to
SPACE
, then press SET.
To correct an incorrect character:
1) Press ON SCREEN CONTROL % / / @ / # to move to or , then
press SET until the incorrect character is selected.
2) Press ON SCREEN CONTROL % / / @ / # to move to CANCEL, then
press SET to erase the character.
3) Press ON SCREEN CONTROL % / / @ / # to move in front of an correct
character, then press SET to enter a correct character.
5. Press ON SCREEN CONTROL % / / @ / # to move to “DISC1: MICHEAL (in this example),” then press SET.
The TITLE INPUT: DISC TITLE screen appears.
TITLE INPUT: DISC TITLE screen
6. Enter the disc title, referring to steps 3 and 4.
If the current CD is a CD Text, go to the next step without entering the disc
title.
Continued to the next page.
60
TEXT COMPU LINK Remote Control System
English
7. Press ON SCREEN CONTROL % / / @ / # to move to “DISC1: MY FAVORITE (in this example),” then press SET.
The TITLE INPUT: DISC 1 GENRE screen appears.
8. Press ON SCREEN CONTROL % / to move to the genre you want, then press SET.
The Disc Information screen appears again.
To show the unseen genres, press ON SCREEN CONTROL % / until they appear.
For the MD recorder:
You can write the disc information (disc title and song titles) into the disc. You can only write the song title for the song currently selected.
If you have the CD-MD combination deck, you can also enter the disc information (its performer, disc title, and its music genre) of normal audio CDs into the memory built in the CD-MD combination deck. (To do this, follow the procedure on page
60.)
TITLE INPUT: DISC 1 GENRE screen
Disc Information screen
1. Display the disc information screen by following the procedure on page 56.
2. Press ON SCREEN CONTROL % / to move to “TITLE INPUT,” then press SET.
The DISC TITLE INPUT screen appears on the TV.
3. Enter the title, referring to steps 3 and 4 on page 60.
You can enter up to 32 character for the disc title.
4. Press ON SCREEN CONTROL % / / @ / # to move to the disc title you have just entered, then press SET.
The disc title is stored into the memory, and the SONG TITLE INPUT screen for the currently selected song appears.
You can enter a song title for the song currently selected (indicated in yellow on the
TV screen
).
5. Enter the song title, referring to steps 3 and 4 on page 60.
You can enter up to 32 character for the song title.
6. Press ON SCREEN CONTROL % / / @ / # to move to the song title you have just entered, then press SET.
The song title is stored into the memory, and the Disc Information screen appears again.
DISC TITLE INPUT screen
61
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.
English
IMPORTANT:
To operate JVC’s audio components using this remote control:
You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 54) in addition to the connections using cables with RCA pin plugs (see page 14).
Aim the remote control directly at the remote sensor on the receiver.
Tuner
After pressing FM/AM (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following
operations:
FM/AM: Alternates between FM and AM. 1 — 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For channel number 15, press +10, then 5. For channel number 20, press +10, then
10.
TUNING UP/TUNING DOWN:
Tunes into stations.
FM MODE/MUTE: Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
SEA MODE: Changes the SEA modes.
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
PLAY
D
G
N
I
N
U
T
4 / REW
STOP
REC
TV VOLUME
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
AUDIO
SLEEP
CNTR
MENU
213
REAR (L)
546
(REAR R)
87/P 9
+10
0
100+
P
U
G
N
I
N
U
T
FF / ¢
PAUSE
SURROUND MODE: Changes the DSP modes.
After pressing SOUND CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the
O
N
S
C
L
O
R
M
U
E
N
T
R
N
E
O
E
C
N
following operations: CNTR +/–: Adjusts the center speaker output level for the Surround/DVD
MULTI playback modes.
REAR•(L) +/–: Adjusts the left/right rear speaker output level for the DSP
modes. Adjusts the left rear speaker output level for the DVD MULTI playback mode.
(REAR•R) +/–: Adjusts the right rear speaker output level for the DVD MULTI
playback mode.
DELAY: Selects the delay time of the rear speaker sound. EFFECT: Selects the effect level for the DSP modes. TEST: Turns on or off the test tone output for the Surround mode. CNTR TONE: Selects the center tone level for the Surround/DVD MULTI
playback modes.
Notes:
• If you use the buttons on the front panel or the menu function to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using buttons on the remote control.
• Check to see if its remote control mode selector is set to the correct position. To operate audio system, TVs, and VCRs, set it to “AUDIO/ TV/VCR.”
• Refer also to the manuals supplied with your components.
Note:
After adjusting sounds, press the corresponding source selecting button or CD DISC to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for operating your target source.
CD player
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a CD player: PLAY: Starts playing.
44
4: Returns to the beginning of the current (or previous) track.
44 ¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. PAUSE: Pauses playing. To release it, press PLAY. 1 — 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.
62
Operating JVC’s Audio/Video Components
English
CD player-changer
After pressing CD DISC (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following
operations on a CD player-changer: PLAY: Starts playing.
44
4: Returns to the beginning of the current (or
44
previous) track.
¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. PAUSE: Pauses playing. To release it, press the PLAY
button.
1 — 6, 7/P: Select the number of a disc installed in a CD
player-changer.
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the CD player-changer: 1 — 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
PLAY
D
G
N
I
N
U
T
4 / REW
STOP
REC
TV VOLUME
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
O
N
S
M
E
N
C
R
E
E
N
AUDIO
SLEEP
CNTR
213
REAR (L)
546
(REAR R)
87/P 9
+10
0
100+
P
U
G
N
I
N
U
T
FF / ¢
PAUSE
L
O
R
U
T
N
O
C
MENU
Turntable
After pressing PHONO (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following
operations on a turntable:
PLAY: Starts playing. STOP: Stops playing.
Cassette deck
After pressing TAPE/MD or TAPE CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you
can perform the following operations on a cassette deck:
PLAY: Starts playing. REW: Fast winds the tape from right to left. FF: Fast winds the tape from left to right. STOP: Stops operations. PAUSE: Pauses playing or recording temporarily. To release it, press the PLAY button.
¶¶
REC
¶: Press this button with the PLAY button to start recording.
¶¶
Press this button with the PAUSE button to enter recording pause.
MD recorder
After pressing TAPE/MD or TAPE CONTROL (with the remote control mode selector set to the “AUDIO/TV/VCR” position), you can perform the following operations on the
MD recorder: PLAY: Starts playing.
44
4: Returns to the beginning of the current (or previous) track.
44 ¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. PAUSE: Pauses playing. To release it, press the PLAY button.
¶¶
REC
: Press this button with the PLAY button to start recording.
¶¶
Press this button with the PAUSE button to enter recording pause.
Notes:
• To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 23.)
• You can use either the TAPE/ MD button or the TAPE CONTROL button to activate the buttons listed to the left. If you press TAPE/MD, the playing source also changes. On the other hand, if you press TAPE CONTROL, the playing source does not change.
63
IMPORTANT:
To operate JVC’s video components using this remote control:
• Aim the remote control directly at the remote sensor on the VCR, DVD player or TV, not on the receiver.
• Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control
code of the VCR connected to the VCR jacks is set to code “A.”
VCR
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
VCR : Turns on or off the VCR.
After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:
PLAY: Starts playing. REW: Rewinds a tape. FF: Fast winds a tape. STOP: Stops operations. PAUSE: Pauses playing or recording temporarily. To
release it, press the PLAY button.
¶¶
REC
¶: Press this button with the PLAY button to
¶¶
start recording.
Press this button with the PAUSE button to
enter recording pause.
RM-SR774XU REMOTE CONTROL
VCR
TV/CATV
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
PLAY
D
G
N
I
N
U
T
4 / REW
STOP
REC
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
CHANNEL +/–: Changes the channels on the VCR. 1 – 9, 0: Selects the channels on the VCR.
For channel 5, press 5. For channel 10, press 1, then 0.
O
N
S
M
E
C
R
E
E
AUDIO
SLEEP
CNTR
MENU
213
REAR (L)
546
(REAR R)
87/P 9
+10
0
FM MODE/MUTE
100+
P
U
G
N
I
N
U
T
FF / ¢
PAUSE
TV VOLUME
L
O
R
U
N
T
N
O
C
N
English
Note:
You can use either the VCR button or the VCR CONTROL button to activate the buttons listed to the left. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.
DVD player
After pressing DVD or DVD MULTI (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a DVD player:
PLAY: Starts playing.
44
4: Returns to the beginning of the current (or previous) track.
44 ¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. PAUSE: Stops playing temporarily. To release it, press the PLAY button.
TV
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
TV/CATV/DBS : Turns on or off the TV. TV VOLUME +/–: Adjusts the volume. TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/ VCR”), you can perform the following operations on a TV:
CHANNEL +/–: Changes the channels. 1 – 9, 0, 100+: Selects the channels. RETURN: Alternates between the previously selected channel and the current
channel.
After pressing DVD or DVD MULTI (with the remote
control mode selector set to the “AUDIO/TV/VCR” position), these buttons can
be used for the DVD menu
CNTR
operations.
Note:
For detailed menu operations, refer to the instructions supplied with the discs or the DVD player.
CNTR TONE
TEST
EFFECT
ENTER
213
REAR (L)
546
(REAR R)
87/P 9
MENU
64
Operating Other Manufactures’ Components
English
This remote control supplied with the receiver can transmit control signals for other manufacturers’ VCRs, TVs, CATV converters and DBS tuners. By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.
When operating the other manufacturers’ components, refer also to the manuals supplied with them. To operate these components with the remote control, first you need to set the manufacturer’s code each for the VCR, TV, CATV converter, and DBS tuner.
IMPORTANT:
AUDIO/TV /VCR
CATV /DBS
When using the Remote Control, check to see if its remote control mode selector is set to the correct position: To operate an audio system, TV, and VCR, set it to “AUDIO/TV/ VCR.” To operate a CATV converter and DBS tuner, set it to “CATV/ DBS.”
To change the transmittable signals for operating another manufacturer’s TV
1. Set the remote control mode selector to “AUDIO/TV/ VCR.”
2. Press and hold TV/CATV/DBS .
3. Press TV/DBS.
4. Enter the manufacturer’s code (three digits) using buttons 1 – 9, and 0. See the lists on page 68 to find the code.
5. Release TV/CATV/DBS .
The following buttons can be used for operating the TV (with the remote control mode selector set to “AUDIO/TV/ VCR”):
TV/CATV/DBS : Turns on and off TV. TV VOLUME +/–: Adjusts the volume. TV/VIDEO: Sets the input mode (either TV
or VIDEO).
After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the TV:
CHANNEL +/–: Changes the channels. 1 – 10, 0, 100+(+10): Selects the TV channels.
100+(+10) button will function as the ENTER button if your TV requires pressing ENTER after selecting a channel number.
RM-SR774XU REMOTE CONTROL
TV/CATV
VCR
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
D
PLAY
G
N
I
N
U
T
4 / REW
STOP
REC
TV VOLUME
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
O
N
S
M
E
N
C
R
E
E
N
SLEEP
213 546 87/P9 0
U
O
C
CNTR
REAR (L)
(REAR R)
I
N
U
T
FF / ¢
PAUSE
T
N
AUDIO
MENU
+10
100+
Note:
P
U
G
N
L
O
R
Refer also to the manual supplied with your TV.
6. Try to operate your TV by pressing TV/CATV/DBS .
When your TV turns on or off, you have entered the correct code.
7. If there are more than one code listed for your brand of TV, try each one until the correct one is entered.
65
To change the transmittable signals for operating a CATV converter or DBS tuner
1. Set the remote control mode selector to “CATV/DBS.”
2. Press and hold TV/CATV/DBS .
3. Press TV/DBS.
4. Enter the manufacturer’s code (three digits) using buttons 1 – 9, and 0. See the lists on page 68 to find the code.
5. Release TV/CATV/DBS .
After setting the remote control mode selector to “CATV/ DBS,” you can perform the following operations on the CATV converter or on the DBS tuner: TV/CATV/DBS : Turns on and off the CATV
converter or DBS tuner.
CHANNEL +/–: Changes the channels. 1 – 10, 0, 100+(+10): Selects the channels.
100+(+10) button will function as the ENTER button if your CATV converter or DBS tuner requires pressing ENTER after selecting a channel number.
RM-SR774XU REMOTE CONTROL
TV/CATV
VCR
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
PLAY
D
G
N
I
N
U
T
4 / REW
STOP
REC
TV VOLUME
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
O
N
S
M
U
E
N
C
R
E
E
N
SLEEP
C
AUDIO
CNTR
MENU
213
REAR (L)
546
(REAR R)
87/P 9
+10
0
100+
P
U
G
N
I
N
U
T
FF / ¢
PAUSE
L
O
R
T
N
O
English
Note:
Refer also to the manual supplied with your CATV converter or DBS tuner.
6. Try to operate your CATV converter or DBS tuner by pressing TV/CATV/DBS .
When your CATV converter or DBS tuner turns on or off, you have entered the correct code.
7. If there are more than one code listed for your brand of CATV converter or DBS tuner, try each one until the correct one is entered.
66
Operating Other Manufactures’ Components
English
To change the transmittable signals for operating another manufacturer’s VCR
1. Set the remote control mode selector to “AUDIO/TV/ VCR.”
2. Press and hold VCR .
3. Press VCR.
4. Enter the manufacturer’s code (three digits) using buttons 1 – 9, and 0. See the lists on page 69 to find the code.
5. Release VCR .
The following buttons can be used for operating the VCR (with the remote control mode selector set to “AUDIO/TV/ VCR”): VCR : Turns on and off VCR.
After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:
CHANNEL +/–: Changes the channels on the VCR. 1 – 10, 0, 100+(+10): Selects the channels on the VCR.
100+(+10) button will function as the ENTER button if your VCR requires pressing ENTER after selecting a channel number.
PLAY: Starts playback. STOP: Stops operations. PAUSE: Pauses. REW: Rewinds a tape. FF: Fast winds a tape.
¶¶
REC
¶: Starts recording or enters recording
¶¶
pause.
RM-SR774XU REMOTE CONTROL
TV/CATV
VCR
/DBS
DVD MULTI
DVD TV/DBSVCR
TAPE/MD FM/AMPHONO
CD
SEA
CNTR TONE
MODE
SURROUND
TEST
ENTER
MODE
SOUND
EFFECT
CONTROL
CD
DELAY
DISC
10
FM MODE/MUTE
RETURN
AUDIO/TV /VCR
VOLUME
CATV /DBS
CHANNEL
MUTE
N
W
O
PLAY
D
G
N
I
N
U
T
4 / REW
STOP
REC
TV VOLUME
TV/VIDEO
CONTROL
VCR TAPE
SET EXIT
O
N
S
M
U
E
N
C
R
E
E
N
AUDIO
SLEEP
CNTR
MENU
213
REAR (L)
546
(REAR R)
87/P9
+10
0
100+
P
U
G
N
I
N
U
T
FF / ¢
PAUSE
L
O
R
T
N
O
C
Notes:
• You can use either the VCR button or the VCR CONTROL button to activate the buttons listed to the left. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.
• Refer also to the manual supplied with your VCR.
6. Try to operate your VCR by pressing VCR .
When your VCR turns on or off, you have entered the correct code.
7. If there are more than one code listed for your brand of VCR, try each one until the correct one is entered.
67
Manufacturers’ codes for TV
Anam 003, 004, 009, 068, 161, 425, 426 Anam National 161, 250, 425 Blaupunkt 554 Daewoo 066, 092, 154, 391, 402, 451 ECE 037 Etron 009, 283 Fortress 093 Funai 264, 342 General 186 GoldStar 002, 037, 039, 178, 283, 457, 467 Grundig 535 Hitachi 145 JVC 036, 053, 069, 094, 160 Marantz 054 Matsushita 250 Mitsubishi 150, 241 National 226 NEC 030, 170 Nicamagic 216 Panasonic 161, 250 Philips 037 Pioneer 166 Samsung 060, 090, 427 Sanyo 208, 376, 424 Sharp 093, 256 Sony 000 Telefunken 252 Thomson 560 Toshiba 156, 502 Victor 036, 053, 160, 250, 376
Manufacturers’ codes for CATV converters
Daeryung 008 GoldStar 838 LG Alps 779 Now 776 Samsung 702 Seawoo 780 Tongkook 777, 840 Zenith 000
Manufacturers’ codes for DBS tuner
Dae Young 735 DX Antenna 752 Marantz 200 Panasonic 739 Pantech 747 Samsung 773 Sony 661 Toshiba 486
English
68
Operating Other Manufactures’ Components
English
Manufacturers’ codes for VCR
Akai 281, 288 Anam 037, 162, 226, 240, 278 Anam National 162, 226 Blaupunkt 226 Daewoo 020, 046, 278, 368, 552 Funai 000 General 052 GoldStar 037, 225, 471 Grundig 195 Hitachi 042, 166, 235 JVC 008, 041, 067, 384 Marantz 081 Matsushita 227 Mitsubishi 043, 061, 196 National 226 NEC 038, 040, 370 Panasonic 162, 226, 227, 367 Philips 062, 081 Pioneer 058 Samsung 240, 426, 432 Sanyo 046, 104, 368, 369 Sharp 048, 062, 363 Shintom 072 Sony 032, 033, 034 Telefunken 187 Thomson 320 Toshiba 045, 366 Victor 008, 041, 067, 384
Manufacturers’ codes listed on pages 68 and 69 are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
69
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
English
PROBLEM
The display does not light up.
No sound from speakers.
Sound from one speaker only.
Continuous hiss or buzzing during FM reception.
POSSIBLE CAUSE
The power cord is not plugged in or the
POWER switch pressed to set it in the
OFF position.
Speaker signal cables are not connected.
The SPEAKERS 1 and 2 buttons are not set correctly.
An incorrect source is selected.
Muting is activated.
Speaker signal cables are not connected properly.
The balance is set to one extreme.
Incoming signal is too weak.
The station is too far away.
An incorrect antenna is used.
SOLUTION
Plug the power cord into an AC outlet and/or press position.
Check speaker wiring and reconnect if necessary.
Press SPEAKERS 1 and 2 correctly.
Select the correct source.
Press MUTE to cancel the mute.
Check speaker wiring and reconnect if necessary.
Adjust the balance properly (see page 23).
Connect an outside FM antenna or contact your dealer.
Select a new station.
Check with your dealer to be sure you have the correct antenna.
POWER to set it in the _ON
Occasional cracking noise during FM reception.
No colors on the on-screen display.
Howling during record playing.
“OVERLOAD” starts flashing on the display.
Remote control does not work.
Antennas are not connected properly.
Ignition noise from automobiles.
The color system of the connected TV is not PAL.
Your turntable is too close to speakers.
Speakers are overloaded because of high volume.
Speakers are overloaded because of short circuit of speaker terminals.
The remote control mode selector is not set correctly.
There is an obstruction in front of the remote sensor on the receiver.
Batteries are weak.
Check connections.
Move the antenna farther from automobile traffic.
Connect a PAL TV.
Move speakers away from the turntable.
Rotate the MASTER VOLUME control counterclockwise three or four times, then press STANDBY/ON If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.
Press STANDBY/ON then check the speaker wiring. If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again. If speaker wiring is not short-circuited, contact your dealer.
Set the selector correctly either to “AUDIO/ TV/VCR” or to “CATV/DBS.”
Remove the obstruction.
Replace batteries.
on the front panel.
on the front panel,
70
Specifications
English
Amplifier
Output Power ............................................................At Stereo operation ........................................................... 100 watts per channel, min. RMS,
At Surround operation
Front Channels.................................................................. 70 watts per channel, min. RMS,
Center channel .................................................................. 70 watts, min. RMS, driven into
driven into 4 ohms, at 1 kHz with no more than 0.7 % total harmonic distortion. (IEC268-3/DIN)
50 watts per channel, min. RMS, driven into 8 ohms, at 1 kHz with no more than 0.7 % total harmonic distortion. (IEC268-3/DIN)
driven into 4 ohms at 1 kHz with no more than 0.8 % total harmonic distortion.
4 ohms at 1 kHz, with no more than
0.8 % total harmonic distortion.
Rear channels.................................................................... 70 watts per channel, min. RMS,
Total Harmonic Distortion (8 ohms, 1 kHz) ........................................................................................................ 0.02 %* at 50 watts output
Audio Input Sensitivity/Impedance (1 kHz) ............ PHONO (MM) .................................................................. 2.5 mV/47 k ohms
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD ............. 200 mV/47 k ohms
Audio Output Level .................................................. TAPE/MD, VCR ............................................................... 200 mV
Signal-to-Noise Ratio (’66 IHF/DIN) ...................... PHONO ............................................................................ 70 dB/66 dB
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD ............. 87 dB/67 dB
Frequency Response (8 ohms) ................................. PHONO ............................................................................ 20 Hz to 20 kHz (±1 dB)
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD ............. 20 Hz to 20 kHz (±1 dB)
RIAA Phono Equalization .................................................................................................................................... ±0.5 dB (20 Hz to 20 kHz)
Loudness Control (Volume Control at –30 dB) ................................................................................................... +6 ±1 dB at 100 Hz
S.E.A......................................................................... Center Frequencies ........................................................... 100 Hz, 1 kHz, 10 kHz
Control Range ................................................................... ±10 dB ±2 dB
driven into 4 ohms at 1kHz, with no more than 0.8 % total harmonic distortion.
(* Measured by JVC Audio Analysis System)
+4 ±1 dB at 10 kHz
71
Video
Video Input Sensitivity/Impedance.......................... Composite video: TV SOUND/DBS, VCR, DVD ........... 1 Vp-p/75 ohms
S-video: DVD
(Y: luminance): .............................................................. 1 Vp-p/75 ohms
(C: chrominance, burst): ................................................ 0.286 Vp-p/75 ohms
English
Video Output Level ..................................................Composite video: VCR, MONITOR OUT ...................... 1 Vp-p/75 ohms
Synchronization .................................................................................................................................................... Negative
Signal-to-Noise Ratio ...........................................................................................................................................45 dB
On-Screen Color System.......................................................................................................................................PAL
S-video: MONITOR OUT ................................................1 Vp-p/75 ohms
(Y: luminance): .............................................................. 1 Vp-p/75 ohms
(C: chrominance, burst): ................................................ 0.286 Vp-p/75 ohms
FM tuner (IHF)
Tuning Range........................................................................................................................................................ 87.5 MHz to 108.0 MHz
Usable Sensitivity ..................................................... Monaural ........................................................................... 12.7 dBf (1.2 µV/75 ohms)
50 dB Quieting Sensitivity........................................Monaural ........................................................................... 16.3 dBf (1.8 µV/75 ohms)
Signal-to-Noise Ratio (IHF-A weighted) ................. Monaural ........................................................................... 80 dB at 85 dBf
Total Harmonic Distortion ........................................ Monaural ........................................................................... 0.15 % at 1 kHz
Stereo Separation at REC OUT ........................................................................................................................... 40 dB at 1 kHz
Capture Ratio ........................................................................................................................................................ 1.5 dB at 85 dBf
Stereo ................................................................................ 38.3 dBf (22.5 µV/75 ohms)
Stereo ................................................................................ 73 dB at 85 dBf
Stereo ................................................................................ 0.2 % at 1 kHz
Alternate Channel Selectivity ............................................................................................................................... 60 dB: (±400 kHz)
Frequency Response ............................................................................................................................................. 30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range........................................................................................................................................................ 531 kHz to 1,602 kHz (at 9 kHz
Usable Sensitivity ..................................................... Loop antenna .................................................................... 300 µV/m
Signal-to-Noise Ratio ...........................................................................................................................................50 dB (100 mV/m)
interval) 530 kHz to 1,600 kHz (at 10 kHz interval)
General
Power Requirements .............................................................................................................................................AC 110/127/220/230–240V ,
Power Consumption.............................................................................................................................................. 280 watts
Dimensions (W x H x D) ...................................................................................................................................... 435 x 157 x 412.5 mm
Mass...................................................................................................................................................................... 11.3 kg (25.0 lbs)
Designs & specifications are subject to change without notice.
adjustable with the voltage selector, 50/60 Hz
2 watts (in standby mode)
3
/16 x 6 3/16 x 16 1/4 inches)
(17
72
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.)
Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido)
Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.U.A., o Canadá, a Austrália e o Reino Unido)
IMPORTANT for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.
IMPORTANTE para la línea de la red (CA)
ANTES DE ENCHUFAR EL EQUIPO, compruebe si la tensión de la línea de la red (CA) corresponde con la posición del selector de tensión situado en la parte exterior del equipo, y si es diferente, reajuste el selector de tensión para evitar el riesgo de incendios/ descargas eléctricas.
IMPORTANTE para a ligação à tensão da rede (CA)
ANTES DE LIGAR O APARELHO A UMA TOMADA DA REDE, verifique se a tensão da rede CA corresponde à posição do selector de voltagem localizado na parte externa deste equipamento. Caso não corresponda, reajuste o selector de voltagem a fim de evitar avarias ou riscos de incêndio e choque eléctrico.
LINE VOLTS
EN, SP, PR, CH
VICTOR COMPANY OF JAPAN, LIMITED
JVC
0398OFMMDWJEM
Loading...