Page 1
Do not connect the TV to the mains supply until you have
completed all the connections.
Install the batteries correctly by following the polarity (+ and -) indications
in the battery compartment.
The latest eco-friendly power-saving technology will switch o the TV if
device is left on and idle for 4 hours. Please refer to “Auto Standby” under
the “Time Settings” section of the instruction manual for more detail.
If you select Ireland as the country where you will operate the TV, a
pop-up screen will be display. You will need a 4-digit activation code for
Irish tuning. This code can be found in-store, on the back of your receipt
(if bought in Ireland), or call the customer service team / KNOWHOW.
Well done, your new TV is now ready to use. You will nd that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call:
• UK Call Centre on 0344 561 1234. • Ireland Call Center on 1 890 818 575.
(QSG-LT-32C340-140518V2)
TV
TV Stand Support
TV Base
Remote Control /
AAA Batteries x 2
Screw A x 3
Quick Start Guide
Screw B x 4
1. Lay the TV down on a at surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
2. To install the TV stand, rst attach the stand support to the TV by using 3 screw A. Align with the screw hole then use screws to x the stand support to
the TV.
3. To install the base stand, align the screw holes, then secure with a screw driver (not included) using the 4 screw B provided.
screw in
screw in
Screw A x 3
Screw B x 4
TV Front
Base Stand
Front
Quick Start Guide
32” LED TV
LT-32C340
Thank you for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial
setup.
Please follow this guide for a successful rst time installation.
1
Unpacking
2
Operating Your Remote Control
4
Connecting the Aerial and the Mains Socket
3
Installing the Base Stand
1. Press and lift the back
cover to open the battery
compartment of the
remote control.
Remove all packaging from the unit. Retain the packaging.
If you dispose of it please do so according to any local regulations.
2. Insert two AAA size
batteries. Close the
battery compartment
cove r.
Instruction Manual
Component Adapter Cable
(YPbPr)
This will be shown as GBR for the UK.
This will show the regional country
(e.g. England, Wales, Scotland, NI).
This will allow you to set the region
for your local news service on BBC
and ITV (e.g. London, Beds and
Cambs etc).
You may receive signals from more than
one transmitter within the Secondary
Region, (e.g Beds and Cambs may have
Luton or Sandy Heath).
Target Region Setting
Country Code GBR
Primary Region England
Secondary Region
Tertiary Region
London
During tuning your TV may have received signals
from more than one transmitter. If this has occurred
the Target Region Descriptor screen will be displayed.
This will enable you to select the correct regional
transmission for the local news service that you
require.
Press the buttons to adjust each option's setting
and then press the OK button to conrm.
The rst time you turn the TV on, it will go straight into the First Time Installation menu.
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
OK
UK
Sweden
France
Ireland
Finland
Spain
Denmark
Portugal
Norway
Country
Channel Tuning
DTV : 3 Channel(s)
Radio : 0 Channel(s)
Data : 0 Channel(s)
36% UHF CH
Press [MENU] to skip.
(DTV)
OK
English
Svenska
Dansk
ýesky
Slovak
Norsk
Suomi
Please select an OSD Language
OK
Home Mode
Shop Mode
Mode Select
1. Press the OK button to start First
Time Installation menu.
5. DTV Channel tuning will
commence. This operation may
take up to 3 minutes. The display
will show the progress of the
tuning and the number of
channels found.
2. Press the buttons to
select your desired language to be
displayed on the menu. The
default on-screen menu language
is set as English. Press the OK
button to conrm.
3. Press the buttons to select
your desired mode and then press
the OK button. Press the button
to select Yes to conrm or the
button to select No to cancel
and return to the Mode Select
menu.
4. Press the buttons to
select the country where you will
operate the TV. Press the OK
button to conrm.
5
Turning the TV On for the First Time
6
Target Region Setting
1. Connect one end of the RF coaxial cable to the aerial socket on
the wall and the other end of the cable to the RF (75Ω) socket at
the rear right side of your TV.
2. Connect the mains cable to the mains socket after you have
completed all the connections.
3. At this stage, the TV switches to standby mode. The red LED
indicator will illuminate on the front panel of the TV.
3. In standby mode, press the button on the right side panel of
the TV or on the remote control to turn the TV on. The red LED
indicator will turn blue.
1
2
USB HDMI2 HDMI1(ARC) PC IN RF
COMMON INTERFACE (CI)
HEADPHONE PC AUDIO
5V 500mA
To mains socket
RF Coxial Cable
(not included)
OR
LT-32C340_QSG_RC140518_Annie.pdf 1 18/5/14 10:24 pm
Loading...