JVC LT-19E621 User Guide

LCD TV

LT-19E621

(19” classe/18,50 diagonale)

INSTRUCTIONS MANUAL D’ INSTRUCTIONS

ATTENTION

(19” class/18.50 diagonal)

If you purchase a universal remote control from your local retailer, please contact the remote manufacturer for the required programming code. Si vous utilisez avec cet appareil une télécommande universelle (autre que celle vendue avec ce téléviseur), consultez la documentation accompagnant la télécommande universelle afin de connaître le code numérique correspondant au téléviseur.

AIR/CABLE MODE SELECTION

When shipped from the factory, the Signal Type option is set to the “Cable” (Cable Television) mode. If not using Cable TV, set this menu option to the “Air” position. Lorsque l’appareil sort de l’usine, l’option Signal Type est en mode « Cable » (câblodistribution). Si vous n’utilisez pas la câblodistribution, sélectionnez l’option « Air ».

SÉLECTION DU MODE AIR/CABLE

ATTENTION

FRANÇAIS ENGLISH

IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED

PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL

SI VOUS DEVEZ COMMUNIQUER AVEC LE SERVICE CLIENTÈLE, PRENEZ NOTE

DU NUMÉRO DE MODÈLE AVANT D’APPELER.

CUSTOMER SERVICE – 1-800-289-0984

SERVICE/SERVICE CLIENTÈLE: 1-800-289-0984

POUR OBTENIR DES INFORMATIONS SUR RECYCLAGE, VEUILLEZ CONTACTER LE SERVICE CLIENTÈLE.

FOR RECYCLING INFORMATION, PLEASE CONTACT CUSTOMER SERVICE.

CUSTOMER SERVICE – 1-800-289-0984

SERVICE/SERVICE CLIENTÈLE: 1-800-289-0984

Before operating the unit, please read this manual thoroughly.

Avant de faire fonctionner l’appareil, veuillez lire le présent guide attentivement.

ENGLISH

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE. TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OPEN FLAMES AWAY FROM THIS PRODUCT AT TIMES.

CAUTION: TO PREVENT ELECTRIC SHOCK. DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

However, there is no guarantee that interference will not occur in a particular installation. If

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with the

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Rules could void the user's authority to operate this equipment.

Location of the required marking

The rating sheet and the safety caution are on the rear of the unit.

Important Note:

In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference. Keep the carton and original packaging for future use.

Serial Number:

Model Number:

15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as vases, should not be placed on the apparatus.

16) An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.

17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

19) If an outside antenna or cable system

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE

is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of

GROUND

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE S2898A

CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS POWER SERVICE GROUNDING

ELECTRODE SYSTEM (NEC ART 250, PART H)

antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

20) When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21) Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

22) When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.

23) Sudden high volume sound may cause hearing or speaker damage. When you use headphones, (if the unit is equipped with a headphone jack) keep the volume at a moderate level. If you use headphones continuously with high volume sound, it may cause hearing damage.

24) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker overheating and fire.

25) This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

26) The socket-outlet must be installed near the unit and easily accessible.

CHILD SAFETY: It Makes A Difference How and Where You Use Your Flat Panel Display

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE ISSUE

The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations. Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

The consumer electronics industry is committed to making home entertainment enjoyable and safe.

TUNE INTO SAFETY

One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use of your flat panel display. Carefully read and understand all enclosed instructions for proper use of this product. Don’t allow children to climb on or play with furniture and television sets. Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers. Remember that children can become excited while watching a program, especially on a “larger than life” flat panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or knocked down. Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:

Use a mount that has been recommended by the display manufacturer and/or listed by an independent laboratory (such as UL, CSA, ETL). Follow all instructions supplied by the display and wall mount manufacturers. If you have any doubts about your ability to safely install your flat panel display, contact your retailer about professional installation. Make sure that the wall where you are mounting the display is appropriate to support the weight of the unit/ product and wall mount. If you are unsure, contact a professional installer. A minimum of two people are required for installation. Flat panel displays can be heavy.

IMPORTANT SAFETY INSTRUCTIONS

CONDENSATION

Moisture will form in the operating section of the unit if the unit is brought from cool surroundings into a warm room or if the temperature of the room rises suddenly. When this happens, unit's performance will be impaired. To prevent this, let the unit stand in its new surroundings for about an hour before switching it on, or make sure that the room temperature rises gradually. Condensation may also form during the summer if the unit is exposed to the breeze from an air conditioner. In such cases, change the location of the unit.

HOW TO HANDLE THE LCD PANEL

•

Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.

•

If the LCD panel is broken, make absolutely sure that you do not touch the liquid in the panel. This may cause skin inflammation. If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water.

Possible Adverse Effects on LCD Panel: If a fixed (non-moving) pattern remains on the LCD Panel for long periods of time, the image can become permanently engrained in the LCD Panel and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your LCD Panel on for long periods of time while it is displaying the following formats or images:

•

Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

•

Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on a normal (4:3) display (black bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen (16:9) display (black bars on left and right sides of screen).

The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim any responsibility for these symptoms.

LCD Panels are manufactured using an extremely high level of precision technology, however sometimes

• parts of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction. Do not install the LCD Panel near electronic equipment that produces electromagnetic waves. Some

• equipment placed too near this unit may cause interference. Effect on infrared devices – There may be interference while using infrared devices such as infrared cordless

• headphones.

ENGLISH

SAFETY PRECAUTIONS

The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause overheating. Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When placing on a shelf leave 10 cm (4 inches) free space around the entire unit.

10cm

M4 × 10

Notes when mounting the LCD TV on a wall

If the unit is to be mounted on the wall, contact the retailer where

• you purchased the LCD TV for advice, and have the equipment professionally installed. Incomplete or improper installation may cause injury to you, and/or damage to the LCD TV. Bracket holes: To attach a wall mounting bracket (not supplied) attach

• where indicated in the drawing right. This manufacturer recommends professional installation.

• Utilize an appropriate bracket and fasteners, sufficient to

• accommodate the size and weight of the unit. Assure the wall to which the unit is to be mounted will safely support

• the size and weight of the unit, using the bracket and fasteners you have selected. Keep cords and cables connected to this flat panel display out of

• reach of children. To hang the television on a wall, remove these screws and then

• remove a stand. Before performing work spread cushioning over the base area to lay the TV on.

100mm

Bracket holes

Screws

How to attach the stand

NOTE:

• Unplug the AC cord from the AC INPUT terminal.

• Before beginning this process, assure that the TV is laid on a clean, safe, and cushioned surface to avoid any damage to the unit.

• Do not touch or press the TV-screen, glass might break under pressure.

Place the TV on its front onto a table. Align the stand’s bottom-plate (supplied) as seen here. It will ﬁ t in only one direction. Hold the unit and attach the stand slowly, as shown in ﬁ gure 1.

LCD PANEL SIDE

Figure 1

Figure 2

Finally secure the bottom-plate with 2 screws (supplied) as indicated by the arrows in figure 2.

•

Be sure to follow the instructions. Insufficient tightening or incorrect installation of the stand will not support your unit correctly, and could result in damage or injury from tip-over.

How to remove the stand

When you transport this product, remove the stand and pack ﬂ at against the back of the unit in the carton. To remove the stand, perform these steps in reverse order.

For wall mounting, the base must be removed. To disconnect the base/stand remove the 3 screws from the back (see page 5).

Features

•

LED Backlight System - It realize thin profile, low power consumption, eco-friendly Hg-less design and high

contrast picture.

Integrated Digital Tuner - You can view digital broadcasts without using a Digital TV Set-Top Box.

•

Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for

•

hearing impaired viewers.

Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control

•

adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.

Programmable TV Sleep Timer - Operable from the remote control, the LCD TV can be programmed for up

•

to 120 minutes to turn off automatically.

Digital Audio Jack (Coaxial) - When a component with a built-in Dolby Digital decoder is connected, Dolby

•

Digital sound can produce the effect of being in a movie theater or a concert hall.

HDMI/Component Video Jacks - A VCR, DVD player, satellite receiver or other audio/video component can

•

be connected to this unit.

On-Screen 3 Languages Display - You can select one of 3 languages, English, French or Spanish for on-

•

screen programming.

Power source

TO USE AC POWER

Connect the AC cord plug into this unit’s AC INPUT jack.

Connect the AC cord into an AC outlet.

ENGLISH

Wider Hole and Blade

AC 120V, 60Hz

AC cord (supplied)

NOTE:

•

Please make sure to insert the cord securely at both the LCD TV and the wall outlet. The AC cord has a polarized type AC line plug. If the supplied AC cord does not match your AC outlet, contact

•

a qualified electrician.

WARNING:

DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC

•

CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE. DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE SPECIFIED. THIS COULD CAUSE

•

FIRE, ELECTRICAL SHOCK, OR DAMAGE.

CAUTION:

WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF

•

SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET. DO NOT PLUG/UNPLUG THE AC CORD WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL

•

SHOCK. IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED ONE IS

•

RECOMMENDED. CONTACT CUSTOMER SERVICE AT 1-800-289-0984.

AC outlet

Before using your unit

IMPORTANT SAFETY INSTRUCTIONS ...........3

SAFETY PRECAUTIONS .................................5

How to attach the stand ....................................6

How to remove the stand .................................. 6

Features ............................................................7

Power source ....................................................7

Contents ...........................................................8

Logos & Licenses .............................................8

Parts and functions ...........................................9

Remote control ...............................................10

Antenna connections ......................................11

Cable TV connections .....................................11

Connections to other equipment .....................12

TV operation

Starting setup .................................................15

TV operation ...................................................15

Quick guide for menu operation ......................16

Convenience functions ...................................17

Memorizing channels ......................................18

Checking the digital signal strength ................19

Labeling channels ...........................................19

Labeling video inputs ......................................19

Closed Caption ............................................... 20

CC advanced ..................................................20

Setting the picture size .................................... 21

Time Shift .......................................................22

Additional information

Reception disturbances .................................. 23

Troubleshooting .............................................. 24

Specifications ................................................25

limited WARRANTY ........................................ 26

Logos & Licenses

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Parts and functions

Right sideFront

INPUT/ENTER button MENU button

CH (CHANNEL)

VOL (VOLUME) +/– buttons

POWER button

/ buttons

ENGLISH

Remote sensor

Rear

AC INPUT jack

Power indicator Red: Standby Blue: On

PC/DVI AUDIO IN jack

DIGITAL AUDIO COAXIAL OUT jack

PC MONITOR IN jack

Left side

Press MENU button to display the menu screen.

CH (CHANNEL) (VOLUME) +/– buttons and INPUT/ ENTER button can be used to select the

desired setting during the menu screen operations.

USB input

HDMI/DVI IN jack

ANT. (RF) IN jack

COMPONENT IN jacks

VIDEO IN jacks (VIDEO/AUDIO (L(MONO)/R))

HEADPHONE jack

/ buttons,

VOL

Remote control

3 4

6 7 8 9

1.POWER Button - Used to turn the power on/off to

the LCD TV.

2.Direct Channel Selection Buttons (0-9) - Allows

direct access to any channel of the LCD TV.

3.– Button -This button is used when selecting

digital channels. Also can display the current channel number when viewing the program.

4.SLEEP Button - To set the LCD TV to turn off after a preset amount of time, use the SLEEP button on the remote control.

5.CH (CHANNEL) Buttons - Used to operate the menu functions of the

LCD TV, and to change the channels of the LCD TV.

Before using the remote control, batteries must first be installed.

/ / CURSOR /

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.

2. Install two “AAA” batteries (supplied).

3. Replace the battery compartment cover.

If this symbol is shown, it is only valid in the European union.

11 12

14 15 16

6.MENU Button - Use to display the On-Screen

menu function.

7.AUDIO Button - Change soundtrack language.

8.INPUT SELECT Button - Use to change the

external input.

SCREEN SIZE Button - Used to change the picture size.

10.RECALL Button - This button allows you to go

back to the previous channel selected by just pressing the RECALL button. Press this button again to return to the channel you were watching.

11.MUTING Button - To turn off the sound, press this

button once. The LCD TV will be silenced and the symbol “Muting” will appear on the screen. The muting feature can be released by pressing the

MUTING button again or one of the VOL (VOLUME) + or – buttons.

12.

VOL (VOLUME) + / – / CURSOR

- Used to operate the menu functions of the LCD

TV. Press the to decrease the sound level.

13.ENTER Button - Use to enter or select

information for On-Screen operations.

14.EXIT Button - Press to remove setup menu.

15.CCD Button - Used to display the Closed Caption

menu screen.

16.DISPLAY Button - When you press this button,

the current information will be displayed on a screen. To remove the display from the screen, press this button again.

17.Time Shift control Buttons - See page 22.

Use two “AAA” size batteries. The batteries may last approximately one year depending on how much the remote control is used. For best performance, it is recommended that batteries should be replaced on a yearly basis, or when the remote operation becomes erratic. Do not mix old and new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries in this device:

•

Use only the size and type of batteries specified.

•

Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device.

•

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

•

If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

•

Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)

button to increase, or the button

/ Buttons

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a Cable TV service, see “Cable TV connections”.

Combination VHF/UHF Antenna (Single 75 ohm cable)

Antenna

Jack

75 ohm Coaxial Cable

Connect the 75 ohm cable from the combination VHF/UHF antenna to the Antenna Jack.

Cable TV connections

This TV has an extended tuning range and can tune most cable channels without using a Cable TV Converter box. Some cable companies offer “premium pay channels” where the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the Cable TV company.

For subscribers to basic Cable TV service

75 ohm

Antenna

Jack

Coaxial Cable

For subscribers to scrambled Cable TV service

If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the TV. Follow the connections shown below. Set the TV to the output channel of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.

For basic Cable TV service not requiring a Converter/ Descrambler box, connect the 75 ohm Coaxial Cable directly to the Antenna Jack on the back of the TV.

ENGLISH

Incoming 75 ohm Cable TV Cable

Converter/

Descrambler

75 ohm Cable to TV

Antenna

Jack

For subscribers to unscrambled Cable TV service with scrambled premium channels

If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require the use of a Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available from the Cable TV company or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to tune scrambled channels.

Incoming 75 ohm Cable TV Cable

Splitter

Converter/

Descrambler

A/B Switch

75 ohm Cable to TV

Antenna

Jack

Connections to other equipment

The exact arrangement you use to interconnect various video and audio components to this unit is dependent on the model and features of each component. Check the Owner’s Manual provided with each component for the location of video and audio inputs and outputs.

To connect the LCD TV to a VCR

Left of the unit

To VIDEO/AUDIO IN

To Video/Audio OUT

Video/Audio cord (not supplied)

To connect the LCD TV to a DVD player with Component Video Input

You can enjoy a high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks of your DVD player with the component video cables (not supplied).

VCR

Left of the unit

To Component OUT

DVD

To AUDIO IN

To COMPONENT IN

Component video cord

(not supplied)

Audio cord

(not supplied)

NOTE:

Component Video input of the unit are for use with a device which output 480i/1080i interlaced signals and

•

To Audio OUT

480p/720p progressive signals.

To connect the LCD TV to a camcorder, or a game console

To playback from a camcorder, connect the camcorder to the unit as shown. This unit can also be used as a display device for many video games. However, due to the wide variety of signals generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You’ll need to consult each component’s Owner’s Manual for additional information.

Left of the unit

To VIDEO/AUDIO IN

Video/Audio cord (not supplied)

To Video/Audio OUT

GAME CONSOLE

Connections to other equipment (continued)

Using an AV Amplifier with built-in digital surround

If you are using an AV Amplifier with built-in digital surround sound, you can enjoy various audio systems including Dolby Digital Surround audio that sounds just like the movie.

Connect an AV amplifier with built-in Dolby Digital decoder, etc. as shown below.

Rear of the unit

To DIGITAL AUDIO

COAXIAL OUT

Coaxial digital cable

(not supplied)

To Coaxial

Digital Audio Input

AV Amplifier with built-in digital surround decoder as listed above

Front

Speaker

(Left)

Surround Speaker (Left)

Subwoofer

Center Speaker

Front Speaker (Right)

Surround Speaker (Right)

NOTE:

When you are viewing digital broadcast, this unit will not work in conjunction with DTS audio or MPEG audio.

• There will be no sound output if connected to an AV amplifier with a built-in DTS decoder or MPEG decoder. Digital Audio Output terminal does not output the sounds from devices connected by HDMI.

•

To connect the LCD TV to a PC (Personal Computer)

BEFORE YOU CONNECT THIS TV TO YOUR PC, CHANGE THE ADJUSTMENT OF YOUR PC’S RESOLUTION AND REFRESH RATE (60 HZ).

Connect one end of a (male to male) VGA cable to the video cord of the computer and the other end to the connector PC MONITOR IN on the rear of the case of a Multimedia computer, connect the audio cord to the audio output of your Multimedia computer and to the AUDIO IN connector of the PC/DVI AUDIO IN jack of the TV. You can also connect the PC with HDMI cable. If you use HDMI cable, you don’t have to connect the audio cord. If you use DVI-to-HDMI cable, please connect audio cord as same way as VGA cable. Press INPUT SELECT on the remote control to select PC mode. Switch on the computer. The TV can operate as the computer monitor.

. Attach the connectors firmly with the screws on the plug.

VGA

ENGLISH

Rear and left of the unit

Monitor Display modes

Mode Resolution Refresh rate VGA 640x480 60/ 72/ 75 Hz

VGA 720x400 70Hz SVGA 800x600 56/ 60/ 72/ 75 Hz XGA 1024x768 60/ 70/ 75 Hz

To PC/DVI AUDIO IN

To PC MONITOR IN

VGA cable (not supplied)

To HDMI/DVI IN

HDMI cable (not supplied)

WXGA 1280x768 60Hz WXGA 1360x768 60Hz

To return to normal mode

Press INPUT SELECT again.

Audio cord (not supplied)

NOTE:

The on-screen displays will have a different appearance in PC mode than in TV mode.

• If there is no video signal from the PC when the unit is in PC mode, “No signal” will appear on the TV-screen.

•

Connections to other equipment (continued)

To connect a HDMI or a DVI device to the unit

The HDMI/DVI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital video from a DVI device. When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate analog audio cords required.

Rear and left of the unit

To PC/DVI AUDIO IN

NOTE:

When using HDMI/DVI IN to connect your HDMI or DVI devices, you must select the corresponding

• audio input source (HDMI or DVI) on the menu screen (see page 17). Otherwise you will only see the image with no sound.

Audio cord (not supplied)

HDMI - to - DVI adapter cable

(HDMI type A connector)

To HDMI/DVI IN

(not supplied)

HDMI cable (type A connector)

(not supplied)

To DVI output

DVI device

To HDMI output

HDMI device

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

To turn on the TV, press POWER (POWER indicator on the front of the unit changes blue. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

E-POP Demo Off Signal Type Cable Automatic Search Start

Press or to select “E-POP Demo”, then

3 4

NOTE:

If you press EXIT in the process of “Auto Setup”,

•

the Auto Setup stops and changes to the normal screen.

When you make a menu selection, your changes

•

occur immediately. You do not have to press EXIT to see your changes.

or to select “On” or “Off”.

press On: A TV feature introduction will pop up at the

bottom of the screen.

Off: Turn off the E-POP Demo feature. Press or to select “Signal Type”, then press

or to select “Cable” or “Air”.

Press or to select “Automatic Search”, then press

“Auto Setup” will begin. After the Auto Setup is completed, the TV channel appears on the screen.

Depending on the reception condition, it may

• take up to 30 minutes to complete memorizing digital cable channels. Please allow the process to complete without interruption.

or ENTER.

TV operation

To turn on the TV, press POWER. (POWER indicator on the front of the unit changes blue. It may take approx. 10 seconds for a picture to appear on screen.)

Adjust the volume level by pressing VOL + or – .

The volume level will be indicated on the screen by green bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of green bars also decreases.

Set the Signal Type option to the appropriate

position (see “Air/Cable selection” on page 18). Press the Direct Channel Selection (0-9, –)

buttons to select the channel. (If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to

10-99: Press the 2 digits in order. Example,

100-135: Press the 3 digits in order. Example, to

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button, followed by the remaining number. Example, to select channel 15-1, press 1, 5, –, 1, then press ENTER.

•

The same program may be available on either

•

VHF/UHF/CABLE CHANNELS

VHF 2-13

UHF

14-69

NOTE:

If a channel with no broadcast is selected, the

• sound will automatically be muted. It may take a few seconds for a digital channel

• picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT

SELECT, then press Number buttons (0-4), then press ENTER. You can

select TV, Video, Component, HDMI or PC depending on which input jacks you used to connect your devices.

0.TV

1.Video

2.Component

3.HDMI

4.PC

[0-4]:Select

select channel 2, press 2, then press ENTER.

to select channel 12, press 1, 2, then press ENTER.

select channel 120, press 1, 2, 0, then press ENTER.

If a channel is selected with only audio content, “Audio only” will be displayed on the screen. If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

an analog channel or a digital channel. You may choose to watch either format. If a channel is selected to which you have not subscribed, be displayed on the screen.

Air Cable

Input Select

“Digital channel is encrypted” will

VHF 2-13

STD/HRC/IRC 14-36 (A) (W) 37-59 (AA) (WW) 60-85 (AAA) (ZZZ) 86-94 (86) (94) 95-99 (A-5) (A-1) 100-135 (100) (135) 01 (4A)

or or corresponding

CH /

Press and release CH / . The channel automatically stops at the next channel set into memory. For proper operation, before selecting channels, they should be set into the memory. See “Memorizing channels” on page 18.

ENGLISH

DISPLAY

Press DISPLAY to display the current information on the screen.

When the TV receives a digital signal, the digital information will appear.

62-1 HDTV_Moving_Picture...

CH-1

Digital Air

No Program Information is available

USB Memory Information

: --:--:--

Play Time

Message : Now Live View

USB Memory is unplugged

Full

1080i

Channel number•

Sleep Timer

Off

English

Broadcast program name

• Channel label (if preset)• Signal type• Sleep timer• Audio language• Program guide• Picture size• Resolution• Time Shift display• Station name•

When the TV receives an analog signal, the analog information will appear.

Analog Cable

Mono

Full 480i

Sleep Timer

Off

Channel number• Signal type• Sleep timer• Picture size• Audio information

• Resolution• (Stereo, SAP or Mono)

•

Channel label (if preset)

Press DISPLAY again to clear the call display.

NOTE:

•

After a few seconds, DISPLAY screen will return to normal TV operation automatically.

RECALL

This button allows you to go back to the last channel selected by pressing RECALL. Press RECALL again to return to the last channel you were watching.

MUTING

Press MUTING to switch off the sound. The TV’s sound will be silenced and “Muting” will appear on the screen. The sound can be switched back on by pressing this button again or the VOL + or –.

SLEEP

To set the TV to turn off after a preset amount of time, press SLEEP on the remote control. The clock will count up 10 minutes for each press of the SLEEP button (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep time is programmed, the display will appear briefly every ten minutes to remind you that the sleep timer is operating. To confirm the sleep timer setting, press SLEEP and the remaining time will be displayed for a few seconds. To cancel the sleep timer, press SLEEP repeatedly until the display turns to Off.

Quick guide for menu operation

Call menu and for example: Select Language.

Press INPUT SELECT to select TV mode.

Press MENU. The TV menu screen will appear.

3 4

NOTE:

•

Main Menu

Picture

Audio

Channel

Setup

ENTER :Set:Select

Press or to select “Setup”, then press or ENTER.

Press or to select “Language”, then press

or to select the desired language.

…on the following pages the menu can be called in the same way as here.

Press EXIT to return to the normal screen.

If no buttons are pressed for more than about 60 seconds, the menu screen will return to normal operation automatically.

+ 36 hidden pages