Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged,
can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3 Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long
a time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4 Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CDpickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Short-circuit point
(Soldering)
Flexible wire
Short-circuit point
Pickup
Pickup
(No.49817)1-3
Page 3
KD-LH1150,KD-LH1100
Disassembly method
2.1 Main body
2.1.1 Removing the front panel assembly
(See Fig.1)
(1) Push the detach button in the lower left part of the front
panel assembly and remove the front panel assembly in
the direction of the arrow.
2.1.2 Removing the front chassis assembly
(See Figs.2 to 4)
• Prior to performing the following procedures, remove the front
panel assembly.
(1) Remove the two screws A on the both sides of the main
body. (See Fig.2.)
(2) Remove the two screws B on the front side of the main
body. (See Fig.3.)
(3) Release the two joints a and two joints b on the both sides
of the main body. (See Fig.2.)
(4) Release the two joints c on the bottom side of the main
body and remove the front chassis assembly in the direction of the arrow. (See Fig.4.)
SECTION 2
Front panel assembly
Detach button
a
Joint
A
Joint a
Front chassis assembly
Fig.1
Joint b
A
Joint b
Fig.2
B
Joint c
Front chassis assembly
Fig.3
Front chassis assembly
Joint c
1-4 (No.49817)
Fig.4
Page 4
2.1.3 Removing the heat sink
(See Fig.5)
(1) Remove the two screws C and two screws D on the left
side of the main body.
KD-LH1150,KD-LH1100
C
2.1.4 Removing the bottom cover
(See Figs.6 and 7)
• Prior to performing the following procedures, remove the front
panel assembly, front chassis assembly and heat sink.
(1) Turn over the main body and release the two joints d, two
joints e and joint f.
CAUTION:
Do not damage the main board when releasing the joint f using
a screwdriver. (See Figs.6 and 7)
Joint
Joint f
D
Heat sink
Fig.5
d
Bottom cover
Joint e
Fig.6
Joint e
Bottom cover
Joint d
Joint f
Fig.7
(No.49817)1-5
Page 5
KD-LH1150,KD-LH1100
2.1.5 Removing the rear bracket
(See Fig.8)
• Prior to performing the following procedures, remove the front
panel assembly, front chassis assembly, heat sink and bottom
cover.
(1) Remove the three screws E, three screws F and three
screws G on the back side of the main body.
(2) Remove the rear bracket.
Reference:
During reassembly, before fixing the rear bracket onto the
main body, insert the subwoofer cable into the slot. (KDLH1150 only)
2.1.6 Removing the main board
(See Fig.9)
• Prior to performing the following procedures, remove the front
panel assembly, front chassis assembly, heat sink, bottom
cover and rear bracket.
(1) Remove the two screws H attaching the main board.
(2) Disconnect the connector CN601 and remove the main
board in an upward direction.
FG
Rear bracket
G
F
EE
Insert Subwoofer cable
into the slot. (KD-LH1150 only)
Fig.8
CN601
H
Main board
H
2.1.7 Removing the CD mechanism assembly
(See Fig. 10)
• Prior to performing the following procedures, remove the front
panel assembly, front chassis assembly, heat sink, bottom
cover, rear bracket and main board.
(1) Remove the three screws J attaching the CD mechanism
assembly.
CD mechanism assembly
Fig.9
J
Top chassis
J
Fig.10
1-6 (No.49817)
Page 6
2.1.8 Removing the front board
(See Figs. 11 to 13)
• Prior to performing the following procedures, remove the front
panel assembly.
(1) Remove the five screws K on the back side of the front pan-
el assembly.
(2) Release the eight joints g.
(3) Take out the front board.
KD-LH1150,KD-LH1100
K
Rear cover
Front board
K
K
Fig.11
Joint g
Joint g
Fig.12
Fig.13
(No.49817)1-7
Page 7
KD-LH1150,KD-LH1100
A
2.2 CD Mechanism Assembly
2.2.1 Removing the top cover
(See Figs.1 and 2)
(1) Remove the two screws A on the both side of the body.
(2) Lift the front side of the top cover and move the top cover
backward to release the two joints a.
Top cover
Joints a
A
Joints a
A
Fig.1
Fig.2
Top cover
1-8 (No.49817)
Page 8
KD-LH1150,KD-LH1100
2.2.2 Removing the connector board
(See Figs.3 to 5)
CAUTION:
Before disconnecting the flexible wire from the pickup, solder
the short-circuit point on the pickup. No observance of this instruction may cause damage of the pickup.
(1) Remove the screw B fixing the connector board.
(2) Solder the short-circuit point on the connector board.
(3) Disconnect the flexible wire from the pickup.
(4) Move the connector board in the direction of the arrow to
release the two joints b.
(5) Unsolder the wire on the connector board if necessary.
CAUTION:
Unsolder the short-circuit point after reassembling.
B
Connector board
Flexible wire
Wires
Joints b
Short-circuit point
Fig.3
Short-circuit point
(Soldering)
Pickup
Flexible wire
Frame
Pickup
Fig.4
B
Connector board
Fig.5
(No.49817)1-9
Page 9
KD-LH1150,KD-LH1100
2.2.3 Removing the DET switch
(See Figs.6 and 7)
(1) Extend the two tabs c of the feed sw. holder and pull out
the switch.
(2) Unsolder the DET switch wire if necessary.
Connector
board
DET switch
DET switch
Pickup
Fig.6
Tab c
Tab c
DET switch wire
Feed sw. holder
Fig.7
1-10 (No.49817)
Page 10
2.2.4 Removing the chassis unit
r
(See Figs.8 and 9)
• Prior to performing the following procedure, remove the top
cover and connector board.
(1) Remove the two suspension springs (L) and (R) attaching
the chassis unit to the frame.
CAUTION:
• The shape of the suspension spring (L) and (R) are different. Handle them with care.
• When reassembling, make sure that the three shafts
on the underside of the chassis unit are inserted to the
dampers certainly.
Suspension spring (R)
KD-LH1150,KD-LH1100
Chassis unit
Suspension spring (L)
Frame
Suspension spring (R)
Chassis unit
Shafts
Damper
Damper
Suspension spring (L)
Fig.8
Shaft
Dampe
Frame
Fig.9
(No.49817)1-11
Page 11
KD-LH1150,KD-LH1100
2.2.5 Removing the clamper assembly
(See Figs.10 and 11)
• Prior to performing the following procedure, remove the top
cover.
(1) Remove the clamper arm spring.
(2) Move the clamper assembly in the direction of the arrow to
release the two joints d.
Clamper arm
spring
Joint d
Joint d
Clamper assembly
Fig.10
Clamper arm spring
Chassis rivet
assembly
Joint d
Clamper
assembly
Chassis rivet assembly
Fig.11
Joint d
1-12 (No.49817)
Page 12
2.2.6 Removing the loading / feed motor assembly
(See Figs.12 and 13)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw C and move the loading / feed motor
assembly in the direction of the arrow to remove it from the
chassis rivet assembly.
(2) Disconnect the wire from the loading / feed motor assembly
if necessary.
CAUTION:
When reassembling, connect the wire from the loading /
feed motor assembly to the flame as shown in Fig.12.
KD-LH1150,KD-LH1100
Loading / feed motor assembly
Fig.12
Loading / feed motor assembly
C
Fig.13
(No.49817)1-13
Page 13
KD-LH1150,KD-LH1100
2.2.7 Removing the pickup unit
(See Figs.14 to 18)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw D and pull out the pu. shaft holder from
the pu. shaft.
(2) Remove the screw E attaching the feed sw. holder.
(3) Move the part e of the pickup unit upward with the pu. shaft
and the feed sw. holder, then release the joint f of the feed
sw. holder in the direction of the arrow. The joint g of the
pickup unit and the feed rack is released, and the feed sw.
holder comes off.
(4) Remove the pu. shaft from the pickup unit.
(5) Remove the screw F attaching the feed rack to the pickup
unit.
2.2.8 Reattaching the pickup unit
(See Figs.14 to 17)
(1) Reattach the feed rack to the pickup unit using the screw F.
(2) Reattach the feed sw. holder to the feed rack while setting
the joint g to the slot of the feed rack and setting the part f
of the feed rack to the switch of the feed sw. holder correctly.
(3) As the feed sw. holder is temporarily attached to the pickup
unit, set to the gear of the joint g and to the bending part of
the chassis (joint h) at a time.
CAUTION:
Make sure that the part i on the underside of the feed
rack is certainly inserted to the slot j of the change lock
lever.
(4) Reattach the feed sw. holder using the screw E.
(5) Reattach the pu. shaft to the pickup unit. Reattach the pu.
shaft holder to the pu. shaft using the screw D.
Joint g
Feed sw.
holder
Part e
Feed rack
Part i
E
F
Pickup unit
Slot j
Fig.15
Joint f
Fig.16
Feed rack
Pickup unit
Feed sw. holder
Pu. shaft
Joint h
D
Pu. shaft
holder
Joint f
Pu. shaft
D
Pu. shaft holder
Feed sw. holder
Pickup unit
Fig.14
Part e
E
Joint g
Pickup unit
Feed rack
Fig.17
Pickup unit
Joint g
Joint f
Feed sw. holder
Fig.18
1-14 (No.49817)
Page 14
KD-LH1150,KD-LH1100
r
2.2.9 Removing the trigger arm
(See Figs.19 and 20)
• Prior to performing the following procedure, remove the top
cover, connector board and clamper unit.
(1) Turn the trigger arm in the direction of the arrow to release
the joint k and pull out upward.
CAUTION:
When reassembling, insert the part m and n of the trigger
arm into the part p and q at the slot of the chassis rivet
assembly respectively and join the joint k at a time.
Chassis rivet assembly
Trigger arm
Chassis rivet
assembly
Joint k
Trigger arm
Fig.19
Part p
Part q
Part m
Part n
2.2.10 Removing the top plate assembly
(See Fig.21)
• Prior to performing the following procedure, remove the top
cover, connector board, chassis unit, and clamper assembly.
(1) Remove the screw H.
(2) Move the top plate assembly in the direction of the arrow to
release the two joints r.
(3) Unsolder the wire marked s if necessary.
H
Fig.20
Top plate assembly
Joints
s
Fig.21
(No.49817)1-15
Page 15
KD-LH1150,KD-LH1100
2.2.11 Removing the mode sw. / select lock arm
(See Figs.22 and 23)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the mode sw. to release from the link plate (joint t)
and turn in the direction of the arrow to release the joint u.
(2) Unsolder the wire of the mode sw. marked s if necessary.
(3) Turn the select lock arm in the direction of the arrow to re-
lease the two joints v.
(4) The select lock arm spring comes off the select lock arm at
the same time.
Top plate
Link plate
Joint u
Joint t
s
Fig.22
Select lock arm
Select lock arm
Mode sw.
Select lock arm
Top plate
Hook w
Select lock
arm spring
Link plate
Joints v
Fig.23
1-16 (No.49817)
Page 16
KD-LH1150,KD-LH1100
2.2.12 Reassembling the mode sw. / select lock arm
(See Figs.24 to 26)
REFERENCE:
Reverse the above removing procedure.
(1) Reattach the select lock arm spring to the top plate and set
the shorter end of the select lock arm spring to the hook w
on the top plate.
(2) Set the other longer end of the select lock arm spring to the
boss x on the underside of the select lock arm, and join the
select lock arm to the slots (joint v). Turn the select lock
arm as shown in the figure.
(3) Reattach the mode sw. while setting the part t to the first
peak of the link plate gear, and join the joint u.
CAUTION:
When reattaching the mode sw., check if the points y and
z are correctly fitted and if each part operates properly.
Select lock arm spring
Hook w
Joint v
Joint v
Select lock arm
Boss x
Fig.24
Joint t
Point y
Link plate
Point z
Link plate
Fig.25
Mode sw.
Select
lock arm
Joint t
Joint u
Fig.26
(No.49817)1-17
Page 17
KD-LH1150,KD-LH1100
2.2.13 Removing the select arm R / link plate
(See Figs.27 and 28)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the select arm R to release from the link plate
(joint a') and turn as shown in the figure to release the two
joints b' and joint c'.
(2) Move the link plate in the direction of the arrow to release
the joint d'. Remove the link plate spring at the same time.
REFERENCE:
Before removing the link plate, remove the mode sw..
Select arm R
Joint b'
Link plate spring
Top plate
Joint c'
Joint a'
Link plate
Link plate
Joint b'
Fig.27
Joint d'
Fig.28
Joint r
2.2.14 Reattaching the Select arm R / link plate
(See Figs.29 and 30)
REFERENCE:
Reverse the above removing procedure.
(1) Reattach the link plate spring.
(2) Reattach the link plate to the link plate spring while joining
them at joint d'.
(3) Reattach the joint a' of the select arm R to the first peak of
the link plate while joining the two joints b' with the slots.
Then turn the select arm R as shown in the figure. The top
plate is joined to the joint c'.
CAUTION:
When reattaching the select arm R, check if the points e'
and f' are correctly fitted and if each part operates properly.
Select arm R
Joint b'
Joint a'
Link plate spring
Joint c'
Joint d'
Joint b'
Joint a'
Fig.29
Link plate
1-18 (No.49817)
Point e'
Point f'
Fig.30
Page 18
KD-LH1150,KD-LH1100
2.2.15 Removing the loading roller assembly
(See Figs.31 to 33)
• Prior to performing the following procedure, remove the
clamper assembly and top plate assembly.
(1) Push inward the loading roller assembly on the gear side
and detach it upward from the slot of the joint g' of the lock
arm rivet assembly.
(2) Detach the loading roller assembly from the slot of the joint
h' of the lock arm rivet assembly.
The roller guide comes off the gear section of the loading
roller assembly.
Remove the roller guide and the HL washer from the shaft
of the loading roller assembly.
(3) Remove the screw J attaching the lock arm rivet assembly.
(4) Push the shaft at the joint i' of the lock arm rivet assembly
inward to release the lock arm rivet assembly from the slot
of the L side plate.
(5) Extend the lock arm rivet assembly outward and release
the joint j' from the boss of the chassis rivet assembly. The
roller guide springs on both sides come off at the same
time.
CAUTION:
When reassembling, reattach the left and right roller
guide springs to the lock arm rivet assembly before reattaching the lock arm rivet assembly to the chassis rivet
assembly. Make sure to fit the part k' of the roller guide
spring inside of the roller guide. (Refer to Fig.34.)
Roller guide
spring
Part k'
Chassis rivet assembly
Loading roller assembly
Loading roller assembly
Roller guide
spring
Fig.32
Boss
Roller guide
Joint h'
Roller guide spring
Loading roller assembly
HL washer
Loading roller assembly
Joint g'
Lock arm rivet assembly
Fig.31
Roller guide
Roller guide spring
Roller guide spring
J
Lock arm rivet assembly
Lock arm rivet assembly
L side plate
Roller guide spring
Joint i'
Part j'
Fig.33
Roller guide
HL washer
Roller shaft assembly
Loading roller
Roller guide spring
Fig.34
(No.49817)1-19
Page 19
KD-LH1150,KD-LH1100
2.2.16 Removing the loading gear 5, 6 and 7
(See Figs.35 and 36)
• Prior to performing the following procedure, remove the top
cover, chassis unit, pickup unit and top plate assembly.
(1) Remove the screw K attaching the loading gear bracket.
The loading gear 6 and 7 come off the loading gear bracket.
(2) Pull out the loading gear 5.
K
Loading gear 5
Loading gear bracket
K
Loading gear 6
Loading gear 5
Loading gear 3
Fig.35
Loading gear bracket
Loading gear 6
Loading gear 7
Fig.36
1-20 (No.49817)
Page 20
KD-LH1150,KD-LH1100
2.2.17 Removing the gears
(See Figs.37 to 40)
• Prior to performing the following procedure, remove the top
cover, chassis unit, top plate assembly and pickup unit.
• Pull out the loading gear 3. (See Fig.35.)
(1) Pull out the feed gear.
(2) Move the loading plate assembly in the direction of the ar-
row to release the L side plate from the two slots m' of the
chassis rivet assembly. (See Fig.37.)
(3) Detach the loading plate assembly upward from the chas-
sis rivet assembly while releasing the joint n'. Remove the
slide hook and loading plate spring from the loading plate
assembly.
(4) Pull out the loading gear 2 and remove the change lock le-
ver.
(5) Remove the E ring and washer attaching the changer gear
2.
(6) The changer gear 2, change gear spring and adjusting
washer come off.
(7) Remove the loading gear 1.
(8) Move the change plate rivet assembly in the direction of the
arrow to release from the three shafts of the chassis rivet
assembly upward. (See Fig.38.)
(9) Detach the loading gear plate rivet assembly from the shaft
of the chassis rivet assembly upward while releasing the
joint p'. (See Figs.38 and 40.)
(10) Pull out the loading gear 4.
Change plate
rivet assembly
Shafts
E ring
Loading plate assembly
Loading plate spring
Joint p'
Loading gear 4
Loading gear plate
rivet assembly
Shaft
Loading gear 2
Loading gear 1
Chassis rivet assembly
Change gear 2
Fig.38
Joint n'
Slide hook
Feed gear
Fig.37
Slot m'
L side plate
Loading plate assembly
Joint n'
Slot m'
Chassis rivet assembly
Chassis rivet assembly
E ring
Washer
Change gear 2
Change gear spring
Adjusting washer
Change plate
rivet assembly
Chassis rivet assembly
L side plate
Slot m'
Slot m'
Fig.39
Loading gear 1
Loading gear 2
Change lock lever
Loading gear 4
Loading gear plate rivet assembly
Fig.40
(No.49817)1-21
Page 21
KD-LH1150,KD-LH1100
2.2.18 Removing the turn table / spindle motor
(See Figs.41 and 42)
• Prior to performing the following procedure, remove the top
cover, connector board, chassis unit and clamper assembly.
(1) Remove the two screws L attaching the spindle motor as-
sembly through the slot of the turn table on top of the body.
(2) Unsolder the wire on the connector board if necessary.
Turn table
L
Fig.41
L
Turn table
1-22 (No.49817)
Spindle motor
Fig.42
Page 22
3.1 Adjustment method
KD-LH1150,KD-LH1100
SECTION 3
Adjustment
Test instruments required for adjustment
1. Digital oscilloscope (100MHz)
2. AM Standard signal generator
3. FM Standard signal generator
4. Stereo modulator
5. Electric voltmeter
6. Digital tester
7. Tracking offset meter
8. Test Disc JVC :CTS-1000
9. Extension cable for check
EXTSH002-22P 1
Standard measuring conditions
Power supply voltage DC14.4V(10.5~16V)
Load impedance 20Kohm(2 Speakers connection)
Output Level Line out 2.0V (Vol. MAX)
How to connect the extension cable for adjusting
Standard volume position
Balance and Bass &Treble volume : lndication"0"
Loudness : OFF
Frequency Band
FM 87.5MHz ~ 107.9MHz
AM 530kHz ~ 1710 kHz
Dummy load
Exclusive dummy load should be used for AM,and FM. For
FM dummy load,there is a loss of 6dB between SSG output
and antenna input.The loss of 6dB need not be considered
since direct reading of figures are applied in this working
standard.
The cardboard is cut in a suitable size.
uses for the insulation stand of mechanism.
Caution:
Be sure to attach the heat sink and rear
bracket onto the power amplifier IC301
and regulator IC901 respectively,
before supply the power.
If voltage is applied without attaching
these parts, the power amplifier IC
and regulator IC will be destroyed
by heat.
Heat sink
Extension cable
EXTSH002-22P
Rear bracket
(No.49817)1-23
Page 23
KD-LH1150,KD-LH1100
3.2 Flow of functional operation unit TOC read
When the pickup correctly moves
to the inner area of the disc
Power ON
v
Set Function CD
When the laser diode correctly
emits
Microprocessor
commands
FMO
TC94A14FA "40"
FEED MOTOR
+TERMINAL
IC501 "4"
REST SW
When correctly focused
FEO
TA2157 "15"
Focus Servo Loop ON
$83
$82
$81
3.3V
Hi-Z
0V
6V
4V
2V
OFF
ON
Pickup feed to the inner area
2.2V
RF signal eye-pattern
remains closed
Disc inserted
YES
Laser emitted
Focus search
Disc rotates
Tracking loop closed
YES
Microprocessor
commands
SEL
TC94A14FA"38"
LD
CN501"15"
"No disc"
display
When the disc correctly rotates
Microprocessor
commands
DMO
TC94A14FA "41"
$84$86$ A200
$84
3.3V
0V
4V
0V
3.3V
2.2V
0V
RF signal eye-pattern
opens
TOC read out
Jump to the first track
Play
Spindle
motor(-)
IC501 "7"
AccelerationServo CLV
Tracking Servo Loop ON
RF signal
6V
3.2
2V
Rough
Servo
0.5 Sec 0.5 Sec
Rough Servo Mode
CLV Servo Mode
(Program Area)
CLV Servo Mode
(Lead-In Area;
Digital :0)
1-24 (No.49817)
Page 24
3.2.1 Feed section
KD-LH1150,KD-LH1100
Is the voltage output at
IC621 pin "40" 5V or 0V?
YES
Is 4V present at both
sides of the feed motor?
YES
Check the feed motor.
3.2.2 Focus section
3.2.3 Spindle section
NOYESNO
Is the wiring for IC681
pin 27?
NO
Is 3.3V present at IC681
pin "20"?
YES
Check the vicinity of
IC621.
NO
Is 6V or 2V present at
IC681 "4" and "5"?
YES
Check the feed motor
connection wiring.
NO
Check IC681.
When the lens is
moving:
4V
Does the S-search
waveform appear at
IC681 pins "10" and "11"?
NO
YES
Check the circuits in
the vicinity of IC501
pins "8","9"and"15".
YES
Check the pickup and
its connections
Check CD 8V
and 5V.
Is the disk rotated?
YES
Does the RF signal
appear at RF test point?
YES
Is the RF waveform at RF
test point distorted?
YES
Proceed to the Tracking
section
3.2.4 Tracking section
When the disc is rotated
at first:
Is the tracking error signal
output at IC681 "9"?
NO
NO
Approx. 1.2V
Is 4V present at IC681
NO
pins "6" and "7"?
YES
Check the spindle motor
and its wiring
NO
Check the circuits in the
vicinity of IC681 "19"~
"24" or the pickup
YESYES
Check the circuit in the
vicinity of IC681 pins
"2"~"12".
Is 4V present at IC621
pins "41" ?
YES
Check the vicinity of
IC681.
Check the pickup and
its connections
NO
Check IC621 and
IC681.
YES
Check IC621.
(No.49817)1-25
Page 25
KD-LH1150,KD-LH1100
3.3 Maintenance of laser pickup
(1) Cleaning the pick up lens
Before you replace the pick up, please try to clean the lens
with a alcohol soaked cotton swab.
(2) Life of the laser diode
When the life of the laser diode has expired, the following
symptoms will appear.
• The level of RF output (EFM output:ampli tude of eye
pattern) will be low.
Is RF output
1.0
±
0.35Vp-p?
NO
Replace it.
YES
O.K
(3) Semi-fixed resistor on the APC PC board
The semi-fixed resistor on the APC printed circuit board
which is attached to the pickup is used to adjust the laser
power.Since this adjustment should be performed to match
the characteristics of the whole optical block, do not touch
the semi-fixed resistor. If the laser power is lower than the
specified value,the laser diode is almost worn out, and the
laser pickup should be replaced. If the semi-fixed resistor
is adjusted while the pickup is functioning normally,the laser pickup may be damaged due to excessive current.
3.4 Replacement of laser pickup
Turn off the power switch and,disconnect the power cord
from the ac outlet.
Replace the pickup with a normal one.(Refer to
"Pickup Removal" on the previous page)
Plug the power cord in,and turn the power on.
At this time,check that the laser emits for about 3seconds
and the objective lens moves up and down.
Note: Do not observe the laser beam directly.
Play a disc.
Check the eye-pattern at RF test point.
Finish.
1-26 (No.49817)
Page 26
SECTION 4
A
Description of major ICs
4.1 BR24C16F-X (IC703) : EEPROM
•Pin layout•Pin function
VCCWPSCLSDA
A0A1A2GND
• Block diagram
SymbolI/OFunction
VCC- Power supply.
GND- GND
A0,A1,A2I No use connect to GND.
SCLI Serial clock input.
SDAI/O Serial data I/O of slave and ward address.
WPIWrite protect terminal.
KD-LH1150,KD-LH1100
A0 1
A1 2
A2 3
GND 4
11bit
Address
decoder
Control circuit
High voltage osc circuit
16kbit EEPROM allay
11bit
START
Slave Ward
Address resister
Power supply
voltage det.
STOP
ACK
8bit
Data
resister
8 Vcc
7 WP
6 SCL
5 SD
(No.49817)1-27
Page 27
KD-LH1150,KD-LH1100
4.2 HA13164A (IC901) : Regulator
• Terminal layout
123456789101112131415
• Block diagram
ANT CTRL
AUDIO OUT
ANT OUT
EXT OUT
CTRL
CD OUT
C3
0.1u
C4
0.1u
C5
0.1u
C6
10u
11
12
10
C1
100u
VCCACC
8
2
1
7
Surge Protector
BIASTSD
15
3
TAB
ILM AJGNDGND
13
C2
0.1u
+B
ACC
BATT.DET OUT
9
COMPOUT
6
VDD OUT
4
SW5VOUT
5
ILMOUT
14
R1
C7
0.1u
C8
0.1u
UNIT R:
C:F
note1) TAB (header of IC)
connected to GND
• Pin function
Pin No.SymbolFunction
1EXTOUTOutput voltage is VCC-1 V when M or H level applied to CTRL pin.
2ANTOUTOutput voltage is VCC-1 V when M or H level to CTRL pin and H level to ANT-CTRL.
3ACCINConnected to ACC.
4VDDOUTRegular 5.7V.
5SW5VOUTOutput voltage is 5V when M or H level applied to CTRL pin.
6COMPOUTOutput for ACC detector.
7ANT CTRLL:ANT output OFF H:ANT output ON
8VCCConnected to VCC.
9BATT DETLow battery detect.
10AUDIO OUTOutput voltage is 9V when M or H level applied to CTRL pin.
11CTRLL:BIAS OFF M:BIAS ON H:CD ON
12CD OUTOutput voltage is 8V when H level applied to CTRL pin.
13ILM AJAdjustment pin for ILM output voltage.
14ILM OUTOutput voltage is 10V when M or H level applied to CTRL pin.
15GNDConnected to GND.
1-28 (No.49817)
Page 28
4.3 IC-PST3424U-X (IC803) : Reset
T
•Pin layout
KD-LH1150,KD-LH1100
VOUT
VDD
• Block diagram
1
2
VDD
43VSS
NC
2
Vref
3
VSS
• Pin function
No.Pin NameFunction
1VoutReset Signal Output PIN
2VDDVDD PIN / Voltage Detect PIN
3NCNon connect
4VSSVSS PIN
+
-
1VOU
4.4 IC-PST9333U-X (IC702) : Regulator
• Pin layout• Block diagram
NC 1
GND 2
• Pin function
Pin No.SymbolFunction
1NCNon connect
2GNDGND terminal
3VOUTReset signal output terminal
4VccVcc terminal/Voltage detect terminal
4 Vcc
3 VOUT
Vcc 4
NC 1
3 VOUT
2 GND
(No.49817)1-29
Page 29
KD-LH1150,KD-LH1100
4.5 LA47505 (IC951) : Power amp.
• Terminal layout
206
11
1
12
4
10
Stand by
Switch
Ripple
Filter
Protective
circuit
Mute
circuit
9
7
8
5
3
2
22
15
25
13
14
16
Muting &
On Time Control
Circuit
protective
circuit
17
19
18
21
23
24
1-30 (No.49817)
Page 30
• Terminal layout
AC CONT1
GND1
OUTFR-
STBY
OUTFR+
Vcc1/2
OUTRR-
GND2
OUTRR+
VREF
INRR
INFR
SGND
INFL
INRL
ONTIME
OUTRL+
GND3
OUTRL-
Vcc3/4
OUTFL+
MUTE
OUTFL-
GND4
NC
• Pin function
Pin No.SymbolFunction
1AC CONT1Header of IC
2GND1Power GND
3OUTFR-Outpur(-) for front Rch
4STBYStand by input
5OUTFR+Output (+) for front Rch
6Vcc1/2Power input
7OUTRR-Output (-) for rear Rch
8GND2Power GND
9OUTRR+Output (+) for rear Rch
10VREFRipple filter
11INRRRear Rch input
12INFRFront Rch input
13SGNDSignal GND
14INFLFront Lch input
15INRLRear Lch input
16ONTIMEPower on time control
17OUTRL+Output (+) for rear Lch
18GND3Power GND
19OUTRL-Output (-) for rear Lch
20Vcc3/4Power input
21OUTFL+Output (+) for front
22MUTEMuting control input
23OUTFL-Output (-) for front
24GND4Power GND
25NCNo connection
KD-LH1150,KD-LH1100
(No.49817)1-31
Page 31
KD-LH1150,KD-LH1100
W
4.6 LA6579H-X (IC681) : 4-Channel bridge driver
• Pin layout & Block diagram
VIN1-A
1
+
VIN1+A
VCCP1
2
3
VIN1_SW
[H]: OP-AMP_A
[L]: OP-AMP_B
[H]
[L]
28
VIN1
27
VIN1-B
-
+
26
VIN1+B
VO+
VO-
VO2+
VO2-
FR
VO3+
VO3-
VO4+
4
5
6
7
FR
8
9
10
Power system
GND
+
Level shift
Level shift
Level shift
Level shift
33k
11k
-
+
H : ON
L : OFF
3.3VREG
(External:PTP Tr)
Signal system
power supply
All outputs ON/OFF
MUTE
Power system GND
Signal system
power supply
+
-
25
24
23
22
FR
21
20
19
S-GND
VIN1-S
MUTE
VREFIN
FR
VCCS
3.3VREG
REGIN
VO4-
VCCP2
VIN4
VIN4G
1-32 (No.49817)
11
12
13
14
11k
33k
+
33k
33k
18
VIN2G
11k
-
17
VIN2
+
16
VIN3G
11k
-
15
VIN3
+
Page 32
• Pin function
Pin No.SymbolFunction
1VIN1-ACH1 input AMP_inverted input
2VIN1+ACH1 input AMP_non-inverted input
3VCCP1CH1 and CH2 power stage power supply
4VO1+Output pin(+)for channel 1
5VO1-CH1 output pin (-) for channel 1
6VO2+Output pin(+)for channel 2
7VO2-Output pin(-)for channel 2
8VO3+Output pin(+)for channel 3
9VO3-Output pin(-)for channel 3
10VO4+Output pin(+)for channel 4
11VO4-Output pin(-)for channel 4
12VCCP2CH3 and CH4 power stage powr supply
13VIN4Input pin for channel 4
14VIN4GInput pin for channel 4(for gain adjustment)
15VIN3Input pin for channel 3
16VIN3GInput pin for channel 3(for gain adjustment)
17VIN2Input pin for channel 2
18VIN2GInput pin for channel 2(for gain adjustment)
8SELIAPC circuit ON/OFF control signal, laser diode (LDO) control signal input
or bottom/peak detection frequency change pin.
KD-LH1150,KD-LH1100
SEL
GND
Hiz
VCC
9TEBITracking error balance adjustment signal input pin
Adjusts TE signal balance by eliminating carrier component from PWM signal (3-state output,
PWM carrier = 88.2kHz) output from TC94A14F/FA
TEBC pin using RC-LPF and inputting DC.
TEBC input voltage:GND~VCC
10TENITracking error signal generation amp negative-phase input pin
11TEOO Tracking error signal generation amp output pin.
Combining TEO signal RFRP signal with TC94A14F/FA configures tracking search system.
12RFDCO RF signal peak detection output pin
13GVSWIAGC/FE/TE amp gain change pin
APC
circuit
LDO
OFFConnected VCC through 1k resistor
ON
Control signal output
ONControl signal output
GVSWMode
GND
Hiz
CD-RW
Normal
VCC
14VROO Reference voltage (VRO) output pin
*VRO=1/2VCC When VCC=3.3V
15FEOO Focus error signal generation amp output pin
16FENIFocus error signal generation amp negative-phase input pin
17RFRPO Signal amp output pin for track count
Combining RFRP signal and TEO signal with TC94A14F/FA configures tracking search system.
18
19
20
21AGCINIRF signal amplitude adjustment amp input pin
22RFOO RF signal generation amp output pin
23RFIIRF signal generation amp input pin
24GND-GND pin
REIS
RFGO
RFGC
I
OIRF signal amplitude adjustment amp output pin
RF amplitude adjustment control signal input pin
Adjusts RF signal amplitude by eliminating carrier component from PWM signal (3-state output,
PWM carrier=88.2kHz)output fromTC94A14F/14FA *RFGC pin using RC-LPF and inputting DC.
*RFGC input voltage:GND~VCC
(No.49817)1-41
Page 41
KD-LH1150,KD-LH1100
4.15 TC94A14FA (IC621) : DSP & DAC
• Terminal layout & block daiagram
48474645444342414039
383736353433
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
LPF
generator
Micro-
controller
interface
Clock
1-bit
DAC
Audio out
Correction
circuit
circuit
Address
circuit
16 k
RAM
Digital
output
PWM
Servo
control
ROM
RAM
CLV servo
Synchronous
guarantee
EFM
decoder
Sub code
decoder
Digital equalizer
automatic
adjustment circuit
A/D
Data
slicer
VCO
PLL
TMAX
D/A
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
64
17
16151413121110123456789
• Pin function
Pin
Symbol I/ODescroption
No
1BCKO Bit clock output pin.32fs48fsor 64fs selectable by command.
2LRCKO L/R channel clock output pin."L" for L channel and "H" for R channel.
Output polarity can be inverted by command.
3AOUTO Audio data output pin. MSB-first or LSB-first selectable by command.
4DOUTO Digital data output pin.Outputs up to double-speed playback.
5IPFO Correction flag output pin. When set to "H" AOUT output cannot be corrected by C2 correction processing.
6V
DD3
7V
SS3
-Digital 3.3V power supply voltage pin.
-Digital GND pin.
8SBOKO Subcode Q data CRCC result output pin. "H" level when result is OK.
9CLCKO Subcode P-W data read I/O pin. I/O polarity selectable by command.
10DATAO Subcode P-W data output pin.
11SFSYO Playback frame sync signal output pin.
12SBSYO Subcode block sync signal output pin. "H" level at S1 when subcode sync is detected.
13HSO
14UHSO
15PV
I/O General-purpose input / output pins.Input port at reset.
-PLL-only 3.3V power supply voltage pin.
DD3
16PDOO EFM and PLCK phase difference signal output pin.
23SLCOO DAC output pin for data slice level generation.
24RFII RF signal input pin. Zin selectable by command.
25AV
- Analog 3.3V power supply voltage pin.
DD3
26RFCTI RFRP signal center level input pin.
27RFZII RFRP signal zero-cross input pin.
28RFRPI RF ripple signal input pin.
29FEII Focus error signal input pin.
30SBADI Sub-beam adder signal input pin.
31TEII Tracking error input pin. Inputs when tracking servo is on.
32TEZII Tracking error signal zero-cross input pin.
33FOOO Focus equalizer output pin.
34TROO Tracking equalizer output pin.
35VREF- Analog reference power supply voltage pin.
36RFGCO RF amplitude adjustment control signal output pin.
37TEBCO Tracking balance control signal output pin.
38SELO APC circuit ON/OFF signal output pin. At laser on, high impedance with UHS="L",
4GE30938-003AHEAT SINKLH1150JD
5GE30393-002ABOTTOM COVER
6FSMA3005-001INSULATOR
7QYSDST2604ZSCREW2.6mm x 4mm(x3)
8FSKZ4005-001SCREW(x2)
9QYSDST2606ZSCREW2.6mm x 6mm(x2)
10QYSDST2604ZSCREW2.6mm x 4mm(x3)
66GE30912-006AREAR BRACKET
67QYSDST2606ZSCREW2.6mm x 6mm
68QYSDST2606ZSCREW2.6mm x 6mm
69QYSDST2606ZSCREW2.6mm x 6mm
70QYSDSF2606ZSCREW2.6mm x 6mm(x2)
71QYSDSF2606ZSCREW2.6mm x 6mm
72GE40136-001AIC BRACKET
73GE40124-001AREG BRACKET
74GE30857-001ALED HOLDER(x2)
75FSYH4036-013SHEET
76GE30937-002ANAVI BASE
77GE40174-001AINSULATOR
78FSYH4036-046SHEET
Part No.Part NameDescriptionLocal
3-3
Page 62
KD-LH1150,KD-LH1100
CD mechanism assembly and parts list
Grease
TNG-87
GP-501MK
CFD-005Z
GP-501A
C
112
24
31
22
61
26
36
29
Block No.
M
M
B
M
TN-2001-1011
111
74
72
35
116
34
111
33
25
73
85
15
A
19
B
21
62
D
75
112
114
11
38
30
A
23
13
32
2
111
37
27
101
93
76
94
122
100
84
73
95
38
74
100
a
14
75
94
96
77
123
97
81
32
a
113
99
28
115
D
111
91
90
89
111
93
71
C
B
92
82
18
20
87
125
88
3
12
121
16
17
124
83
86
111
3
98
83
4
1
3-4
Page 63
CD mechanism
Block No. [M][B][M][M]
Symbol No.
130320101TFRAME
230320102TTOP COVER
330320115TDANPER F
430320116TDANPER R
11303205505TCHASSIS RIVET
12303205503TCHANGE P. RVT A
13303205301TCLAMPER ASS'Y
14303205304TSPINDLE MOTOR A
1530320502TCLAMPER ARM
1630320503TCHANGE GEAR SPG
1730320505TCHANGE GEAR 2
1830320506TFEED GEAR
1930320507TFEED RACK
2030320509TCHANGE LOCK RAR
2130320510TFEED SW HOLDER
2230320511TPU SHAFT HOLDER
2330320513TCLAMPER SUB SPG
2430320514TFD SUB HOLDER
2530320518TTOP PLATE
2630320519TSELECT LOCK ARM
2730320520TTRIGGER ARM
2830320521TSLIDE HOOK
2930320522TPU SHAFT
3030320525TCLAMPER ARM SPG
3130320526TSELECT L ARM SP
3230320538TSUSPENSION SP R
3330320529TSELECT ARM R
3430320530TLINK PLATE
3530320531TLINK PLATE SPG
3630320523TCUSHION F
3730320524TCUSHION R
3830320539TSUSPENSION SP L
6169011614TPICKUP OPT-725
6264180406TDET SW ESE22
71303210301TCONN PWB ASS'Y
7230321002TMODE SW
7330321003TLOAD MOTOR WIRE
7430321005TMODE SW WIRE
7530321009TSL WIRE
7630321011TWIRE HOLDER
7719501403TWIRE CLUMPER
81303211301TROLLER SHAFT AS
82303211501TL GEAR PLATE RV
83303211302TLOADING PLATE A
84303211502TLOCK ARM RV ASS
85303211303TL/F MOTOR ASS'Y
8630321101TLOADING GEAR 1
8730321102TLOADING GEAR 2
8830321103TLOADING GEAR 3
8930321104TLOADING GEAR 4
9030321105TLOADING GEAR 5
9130321106TLOADING GEAR 6
9230321107TLOADING GEAR 7
9330321111TROLL E R GUI D E
9430321114TROLLER GUIDE SP
9530321116TDISC STOPPER AR
9630321117TDISC ST ARM SPG
9730321118TLD GEAR BRACKET
9830321125TL SIDE PLATE
9930321131TLOAD PLATE SPG
10030321133TLDG ROLLER
10118211223TCOLLAR SCREW
1119P0420031TSCREW
1129P0420041TTAP.SCREW
1139B0320041TSCREW
1149C0117183TSCREW
1159C0120203TSCREW
1169C0317503TSCREW
1219W0130170TPW 3.5X8X0.3
1229W0513060THL WASHER
1239W0710070TL WASHER
1249E0100152TE RING
1259W0113020TPW 2.1X4X0.13
Part No.Part NameDescriptionLocal
KD-LH1150,KD-LH1100
3-5
Page 64
KD-LH1150,KD-LH1100
Electrical parts list
Main board
Symbol No.
IC131BU4066BCFV-XIC
IC132NJM4565V-XIC
IC171NJM4565V-XIC
IC281BA3220FV-XIC
IC301BA3220FV-XIC
IC601TA2157FN-XRF AMP IC
IC621TC94A14FACD LSI IC
IC681LA6579H-XBTL DRIVER IC
IC70 1UPD784217AGC204 IC
IC702IC-PST9333U-XIC
IC703BR24L16F-W-XIC
IC781HD74HC126FP-XIC
IC901HA13164AIC
IC911TDA7404D-XIC
IC912M62449FP-XIC
IC921NJM2360AM-XIC.C.M
IC951LA47505IC
D716UDZS6.2B-XZ DIODE
D717SML-310LT/MN/-X LED
D718SML-310LT/MN/-X LED
D719SML-310LT/MN/-X LED
D720UDZS6.2B-XZ DIODE
D9011N5404-TU-15DIODE
D904RB160M-30-XSB DIODE
D905RB160M-30-XSB DIODE
D921RB160M-30-XSB DIODE
D941UDZS11B-XZ DIODE
D9421SS355-XSI DIODE
D9511SS355-XSI DIODE
C1NCB31EK-473XC CAPACITOR0.047uF 25V K
C2NCB31HK-103XC CAPACITOR0.01uF 50V K
C3QEKJ1CM-476ZE CAPACITOR47uF 16V M
C4QEKJ1CM-476ZE CAPACITOR47uF 16V M
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M LH1100JD
C6QEKJ1AM-107ZE CAPACITOR100uF 10V M
C7QEKJ1AM-107ZE CAPACITOR100uF 10V M LH1100JD
C7QEKJ1AM-107ZE CAPACITOR100uF 10V M
C10NCB31EK-473XC CAPACITOR0.047uF 25V K
C25NCS31HJ-331XC CAPACITOR330pF 50V J
C27QEKJ1HM-104ZE CAPACITOR0.1uF 50V M
C101NCB31EK-223XC CAPACITOR0.022uF 25V K
C102QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C103NCS31HJ-821XC CAPACITOR820pF 50V J
C104NBE21CM-105XTA E CAPACITOR1uF 16V M
C110NBE21CM-105XTA E CAPACITOR1uF 16V M
C115NFV81CM-105XTS E. CAPACITOR1uF 16V M
C116NFV81CM-105XTS E. CAPACITOR1uF 16V M
C117NCB31HK-331XC CAPACITOR330pF 50V K
C118NCB31HK-331XC CAPACITOR330pF 50V K
C120QEKJ1CM-476ZE CAPACITOR47uF 16V M
C122NCB31EK-473XC CAPACITOR0.047uF 25V K
C123NCS31HJ-101XC CAPACITOR100pF 50V J
C124NBE21CM-105XTA E CAPACITOR1uF 16V M
C125NBE21CM-225XTA E CAPACITOR2.2uF 16V M
C126QERF1CM-107ZE CAPACITOR100uF 16V M
C127NCB31HK-472XC CAPACITOR4700pF 50V K
C131QEKJ1CM-106ZE CAPACITOR10uF 16V M
C132NCB31EK-333XC CAPACITOR0.033uF 25V K
C133NCB31EK-273XC CAPACITOR0.027uF 25V K
C134NCB31EK-273XC CAPACITOR0.027uF 25V K
C135NCB31HK-562XC CAPACITOR5600pF 50V K
C136NCB31EK-123XC CAPACITOR0.012uF 25V K
C137QEKJ1CM-476ZE CAPACITOR47uF 16V M
C138NBE40JM-106XTA E CAPACITOR10uF 6.3V M
C139QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C140NCB31HK-682XC CAPACITOR6800pF 50V K
C141NCB31EK-823XC CAPACITOR0.082uF 25V K
C142QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C143NCB31EK-473XC CAPACITOR0.047uF 25V K
C144NCS31HJ-101XC CAPACITOR100pF 50V J
C151NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C152NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C171NCS31HJ-101XC CAPACITOR100pF 50V J
C172NCB31HK-822XC CAPACITOR8200pF 50V K
C173QERF0JM-226ZE CAPACITOR22uF 6.3V M
C174NCB31HK-102XC CAPACITOR1000pF 50V K
Part No.Part NameDescriptionLocal
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
3-6
Page 65
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
KD-LH1150,KD-LH1100
Part No.Part NameDescriptionLocal
C175QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C176QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C177QEKJ1CM-476ZE CAPACITOR47uF 16V M
C181NCB31EK-473XC CAPACITOR0.047uF 25V K
C191QERF1HM-105ZE CAPACITOR1uF 50V M
C192QERF1CM-226ZE CAPACITOR22uF 16V M
C193NCB31EK-473XC CAPACITOR0.047uF 25V K
C194QERF1HM-224ZE CAPACITOR0.22uF 50V M
C201NCB31EK-223XC CAPACITOR0.022uF 25V K
C202QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C203NCS31HJ-821XC CAPACITOR820pF 50V J
C204NBE21CM-105XTA E CAPACITOR1uF 16V M
C210NBE21CM-105XTA E CAPACITOR1uF 16V M
C215NFV81CM-105XTS E. CAPACITOR1uF 16V M
C216NFV81CM-105XTS E. CAPACITOR1uF 16V M
C217NCB31HK-331XC CAPACITOR330pF 50V K
C218NCB31HK-331XC CAPACITOR330pF 50V K
C224NBE21CM-105XTA E CAPACITOR1uF 16V M
C251NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C252NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C253NBE21CM-225XTA E CAPACITOR2.2uF 16V M
C254NBE21CM-225XTA E CAPACITOR2.2uF 16V M
C261NCB31CK-823XC CAPACITOR0.082uF 16V K
C262NCB31CK-104XC CAPACITOR0.1uF 16V K
C263NCB31EK-273XC CAPACITOR0.027uF 25V K
C264NCB31CK-393XC CAPACITOR0.039uF 16V K
C265NCB31HK-123XC CAPACITOR0.012uF 50V K
C266NCB31HK-153XC CAPACITOR0.015uF 50V K
C267NCB31HK-472XC CAPACITOR4700pF 50V K
C268NCB31HK-682XC CAPACITOR6800pF 50V K
C269NCB31HK-182XC CAPACITOR1800pF 50V K
C270NCB31HK-272XC CAPACITOR2700pF 50V K
C271NCS31HJ-101XC CAPACITOR100pF 50V J
C272NCB31HK-822XC CAPACITOR8200pF 50V K
C273QERF0JM-226ZE CAPACITOR22uF 6.3V M
C274NCB31HK-102XC CAPACITOR1000pF 50V K
C275QEKJ1EM-475ZE CAPACITOR4.7uF 25V M
C276QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C281NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C282NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C283QEKJ1CM-476ZE CAPACITOR47uF 16V M
C284NCB31HK-103XC CAPACITOR0.01uF 50V K
C287QERF1AM-107ZE CAPACITOR100uF 10V M
C288NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C289NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C290QEKJ1AM-107ZE CAPACITOR100uF 10V M
C294QEKJ1AM-107ZE CAPACITOR100uF 10V M
C301NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C302NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C303QEKJ1CM-476ZE CAPACITOR47uF 16V M
C304NCB31HK-103XC CAPACITOR0.01uF 50V K
C307QERF1AM-107ZE CAPACITOR100uF 10V M
C308NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C309NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C310QERF1AM-107ZE CAPACITOR100uF 10V M
C351NBE21CM-225XTA E CAPACITOR2.2uF 16V M
C352NBE21CM-225XTA E CAPACITOR2.2uF 16V M
C361NCB31CK-823XC CAPACITOR0.082uF 16V K
C362NCB31CK-104XC CAPACITOR0.1uF 16V K
C363NCB31EK-273XC CAPACITOR0.027uF 25V K
C364NCB31CK-393XC CAPACITOR0.039uF 16V K
C365NCB31HK-123XC CAPACITOR0.012uF 50V K
C366NCB31HK-153XC CAPACITOR0.015uF 50V K
C367NCB31HK-472XC CAPACITOR4700pF 50V K
C368NCB31HK-682XC CAPACITOR6800pF 50V K
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
LH1150CD,
LH1150JD
C369NCB31HK-182XC CAPACITOR1800pF 50V K
C370NCB31HK-272XC CAPACITOR2700pF 50V K
C601QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C602NCB31HK-103XC CAPACITOR0.01uF 50V K
C603QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C604NCB31HK-103XC CAPACITOR0.01uF 50V K
C605NCB31HK-682XC CAPACITOR6800pF 50V K
C606QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C607NCB31HK-103XC CAPACITOR0.01uF 50V K
C608NCB31CK-104XC CAPACITOR0.1uF 16V K
C609NCB31CK-104XC CAPACITOR0.1uF 16V K
C610NCS31HJ-5R0XC CAPACITOR5pF 50V J
C611NCS31HJ-680XC CAPACITOR68pF 50V J
C612NCB31HK-103XC CAPACITOR0.01uF 50V K
C613NCB31HK-103XC CAPACITOR0.01uF 50V K
C614NCB31HK-103XC CAPACITOR0.01uF 50V K
C621NCB31HK-103XC CAPACITOR0.01uF 50V K
C622QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C623NCS31HJ-470XC CAPACITOR47pF 50V J
C624NCB31EK-153XC CAPACITOR0.015uF 25V K
C625NCB31HK-103XC CAPACITOR0.01uF 50V K
C626NCB31HK-272XC CAPACITOR2700pF 50V K
C627NCB31HK-103XC CAPACITOR0.01uF 50V K
C628QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C629NCB31EK-333XC CAPACITOR0.033uF 25V K
C630NCB31EK-333XC CAPACITOR0.033uF 25V K
C631NCS31HJ-471XC CAPACITOR470pF 50V J
C632NCS31HJ-471XC CAPACITOR470pF 50V J
C633NCB31EK-473XC CAPACITOR0.047uF 25V K
C634NCB31EK-473XC CAPACITOR0.047uF 25V K
C635NCB31EK-473XC CAPACITOR0.047uF 25V K
C636NCB31EK-473XC CAPACITOR0.047uF 25V K
C637NCB31EK-473XC CAPACITOR0.047uF 25V K
C638NCB31HK-103XC CAPACITOR0.01uF 50V K
C639QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C640NCB31HK-103XC CAPACITOR0.01uF 50V K
C641QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C642NCS31HJ-101XC CAPACITOR100pF 50V J
C643NCB31HK-103XC CAPACITOR0.01uF 50V K
C644QEKJ1HM-105ZE CAPACITOR1uF 50V M
C645QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C646NCB31HK-103XC CAPACITOR0.01uF 50V K
C647NCB31HK-102XC CAPACITOR1000pF 50V K
C648QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C649QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C651NCS31HJ-100XC CAPACITOR10pF 50V J
C652NCS31HJ-100XC CAPACITOR10pF 50V J
C682QEKJ1CM-226ZE CAPACITOR22uF 16V M
C683NCB31CK-104XC CAPACITOR0.1uF 16V K
C684QEKJ1AM-227ZE CAPACITOR220uF 10V M
C685NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C686NCB31EK-473XC CAPACITOR0.047uF 25V K
C687NCB31EK-473XC CAPACITOR0.047uF 25V K
C688NCB31EK-473XC CAPACITOR0.047uF 25V K
C689NCB31EK-473XC CAPACITOR0.047uF 25V K
C701NCB31CK-104XC CAPACITOR0.1uF 16V K
C702QEKJ1AM-227ZE CAPACITOR220uF 10V M
C703NCS31HJ-8R0XC CAPACITOR8pF 50V J
C704NCS31HJ-270XC CAPACITOR27pF 50V J
C705NCS31HJ-270XC CAPACITOR27pF 50V J
C706NCS31HJ-220XC CAPACITOR22pF 50V J
C707NCB31HK-103XC CAPACITOR0.01uF 50V K
C708QEKJ1AM-227ZE CAPACITOR220uF 10V M
C709NCS31HJ-471XC CAPACITOR470pF 50V J
C710NCB31EK-473XC CAPACITOR0.047uF 25V K
C711NCB31CK-104XC CAPACITOR0.1uF 16V K
C713QEKJ0JM-476ZE CAPACITOR47uF 6.3V M
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QEKJ1AM-227ZE CAPACITOR220uF 10V M
C716NCB31EK-473XC CAPACITOR0.047uF 25V K
C717NCS31HJ-101XC CAPACITOR100pF 50V J
C724QERF1AM-227ZE CAPACITOR220uF 10V M
C725QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C768NCB31CK-104XC CAPACITOR0.1uF 16V K
C769NCB31CK-104XC CAPACITOR0.1uF 16V K
C781NCB31EK-473XC CAPACITOR0.047uF 25V K
C795QEKJ1HM-105ZE CAPACITOR1uF 50V M
C901QEZ0625-338E CAPACITOR3300uF
3-7
Page 66
KD-LH1150,KD-LH1100
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C902QEKJ1CM-226ZE CAPACITOR22uF 16V M
C903QEKJ1CM-226ZE CAPACITOR22uF 16V M
C904NCB31HK-103XC CAPACITOR0.01uF 50V K
C905QEKJ1AM-107ZE CAPACITOR100uF 10V M LH1100JD
C905QEKJ1AM-107ZE CAPACITOR100uF 10V M
C906NCB31CK-104XC CAPACITOR0.1uF 16V K
C907NCB31HK-103XC CAPACITOR0.01uF 50V K
C908QEKJ1AM-227ZE CAPACITOR220uF 10V M
C910QEKJ1CM-106ZE CAPACITOR10uF 16V M
C911NCB31CK-104XC CAPACITOR0.1uF 16V K
C912QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C914QEKJ1CM-226ZE CAPACITOR22uF 16V M
C917NCB31CK-473XC CAPACITOR0.047uF 16V K
C920NBE21CM-475XTA E CAPACITOR4.7uF 16V M
C921QERF1AM-107ZE CAPACITOR100uF 10V M LH1100JD
C921QEKJ1AM-227ZE CAPACITOR220uF 10V M
C922NCB31HK-272XC CAPACITOR2700pF 50V K
C923QEKJ1CM-107ZE CAPACITOR100uF 16V M
C924NCB31EK-473XC CAPACITOR0.047uF 25V K
C929NCB31CK-473XC CAPACITOR0.047uF 16V K
C930NBE21AM-106XTA E CAPACITOR10uF 10V M
C941QEKJ1CM-476ZE CAPACITOR47uF 16V M
C942QEKJ0JM-107ZE CAPACITOR100uF 6.3V M
C945NCB31CK-104XC CAPACITOR0.01uF 16V K LH1100JD
C945NCB31CK-104XC CAPACITOR0.1uF 16V K
C951QERF1CM-476ZE CAPACITOR47uF 16V M
C952NCB31AK-224XC CAPACITOR0.22uF 10V K
C953QEKJ1CM-107ZE CAPACITOR100uF 16V M
C954QEKJ1CM-226ZE CAPACITOR22uF 16V M
C955QEKJ1HM-475ZE CAPACITOR4.7uF 50V M
C956NCB31EK-104XC CAPACITOR0.1uF 25V K
C957NCB31EK-104XC CAPACITOR0.1uF 25V K
C958NCB31EK-104XC CAPACITOR0.1uF 25V K
C959NCB31EK-104XC CAPACITOR0.1uF 25V K
C961NCS31HJ-101XC CAPACITOR100pF 50V J
C962NCS31HJ-101XC CAPACITOR100pF 50V J
C963NCS31HJ-101XC CAPACITOR100pF 50V J
C964NCS31HJ-101XC CAPACITOR100pF 50V J
C965NCS31HJ-101XC CAPACITOR100pF 50V J
C966NCS31HJ-101XC CAPACITOR100pF 50V J
C967NCS31HJ-101XC CAPACITOR100pF 50V J
C968NCS31HJ-101XC CAPACITOR100pF 50V J
C969QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
C970QEKJ1HM-225ZE CAPACITOR2.2uF 50V M
L1NQL114K-100XCOIL10uH K
L621NQL114K-470XINDUCITOR47uH K
L622NQL114K-470XINDUCITOR47uH K
L624NQL114K-470XINDUCITOR47uH K
L701NQL114K-470XINDUCITOR47uH K
L702NQL114K-470XINDUCITOR47uH K
L901QQR1378-001CHOKE COIL
L921NQLZ007-151XCOIL150uH
L922NQL114M-4R7XCOIL4.7uH M
BZ795QAN0023-001ZBUZZER
CN131QGA2006C1-04CONNECTOR W-B (1-4)
CN601QGB2027M4-22SCONNECTOR B-B (1-22)
CN701QNZ0605-001CAR CONNECTOR
CN901QNZ0611-00116P CONNECTOR
CN902QNZ0095-001CONNECTOR
J1QNB0100-002CAR ANT JACK
J121QNN0490-001PIN JACK
S701QSW0451-001DETECT SW
S702QSW0451-001DETECT SW
S703QSQ1A11-V06ZTACT SW I/M
D401MA152WK-XDIODE
D402SML-310LT/MN/-X LED
D403SML-310LT/MN/-X LED
D405SML-310LT/MN/-X LED
D406SML-310LT/MN/-X LED
D407SML-310LT/MN/-X LED
D408SML-310LT/MN/-X LED
D409SML-310LT/MN/-X LED
D410SML-310LT/MN/-X LED
D411SML-310LT/MN/-X LED
D412SML-310LT/MN/-X LED
D413SML310BAT/JKL-X LED
D414SML310BAT/JKL-X LED
D415SML-310LT/MN/-X LED
D416SML-310LT/MN/-X LED
D417SML-310LT/MN/-X LED
D418SML-310LT/MN/-X LED
D419SML-310LT/MN/-X LED
D420SML-310LT/MN/-X LED
D421SML-310LT/MN/-X LED
D422SML-310LT/MN/-X LED
D423UDZS6.2B-XZ DIODE
D424UDZS6.2B-XZ DIODE
D425UDZS6.2B-XZ DIODE
D426UDZS6.2B-XZ DIODE
D427UDZS6.2B-XZ DIODE
D428UDZS6.2B-XZ DIODE
D429UDZS6.2B-XZ DIODE
C451NCB31EK-473XC CAPACITOR0.047uF 25V K
C452NCB31EK-473XC CAPACITOR0.047uF 25V K
C453NCB31EK-473XC CAPACITOR0.047uF 25V K
C454NCB31EK-473XC CAPACITOR0.047uF 25V K
C455NCB31EK-473XC CAPACITOR0.047uF 25V K
C456NCB31EK-473XC CAPACITOR0.047uF 25V K
C457NCB31EK-473XC CAPACITOR0.047uF 25V K
C458NCB31EK-473XC CAPACITOR0.047uF 25V K
C459NCB31EK-473XC CAPACITOR0.047uF 25V K
C801NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C802NCB31EK-473XC CAPACITOR0.047uF 25V K
C804NCS31HJ-471XC CAPACITOR470pF 50V J
C805NCS31HJ-471XC CAPACITOR470pF 50V J
C806NCB31EK-473XC CAPACITOR0.047uF 25V K
C807NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C808NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C809NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C810NCB31EK-473XC CAPACITOR0.047uF 25V K
C811NCB31EK-473XC CAPACITOR0.047uF 25V K
C812NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C813NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C814NCB31AK-474XC CAPACITOR0.47uF 10V K
C815NCB31AK-474XC CAPACITOR0.47uF 10V K
C816NCB31AK-474XC CAPACITOR0.47uF 10V K
C817NCB31EK-473XC CAPACITOR0.047uF 25V K
C818NCB31EK-473XC CAPACITOR0.047uF 25V K
C819NCB31EK-473XC CAPACITOR0.047uF 25V K
C820NCB31EK-473XC CAPACITOR0.047uF 25V K
C821NCB31EK-473XC CAPACITOR0.047uF 25V K
C822NCB31EK-473XC CAPACITOR0.047uF 25V K
C823NCB31EK-473XC CAPACITOR0.047uF 25V K
C824NCB31EK-473XC CAPACITOR0.047uF 25V K
C825NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C826NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C827NCB31EK-473XC CAPACITOR0.047uF 25V K
C828NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C829NBE20JM-475XTA E CAPACITOR4.7uF 6.3V M
C832NDC31HJ-300XC CAPACITOR30pF 50V J
C833NDC31HJ-300XC CAPACITOR30pF 50V J
C834NBE21CM-105XTA E CAPACITOR1uF 16V M
C835NCB31EK-104XC CAPACITOR0.1uF 25V K
P1FSPG4002-001POLY BAG
P2QPA00801205POLY BAG8cm x 12cm
P3FSYH4036-068SHEET
P4QPA01003003POLY BAG10cm x 30cm
P5QPC03004315PPOLY BAG30cm x 43cm
P6GE30781-002ACARTONLH1100JD
P6GE30926-001ACARTONLH1150CD
P6GE30787-002ACARTONLH1150JD
P7GE10070-001AEPS CUSHON