JVC KD-DV7203, KD-DV7204, KD-DV7205, KD-DV7206 Instructions Manual

DVD/CD RECEIVER KD-DV7204/KD-DV7203

For canceling the display demonstration, see page 5.

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0376-001A

[UI]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

How to use functions mode

If you press MODE, the unit goes into functions mode, then the number buttons and 5/∞ buttons work as different function buttons.

[Within 5 seconds...]

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

“PLEASE” and “EJECT” appear alternately on the display.

• If this does not work, reset your unit.

• Be careful not to drop the disc when it

ejects.

WARNINGS: To prevent accidents and damage

• DO NOT install any unit in locations where; – it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety devices

such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while driving, be sure to look ahead carefully.

• The driver must not watch the monitor while driving.

If the parking brake is not engaged, “DRIVER

MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown. – This warning appears only when the parking

brake wire is connected to the parking brake system built in the car (refer to the Installation/ Connection Manual).

CONTENTS

Introduction ............................................. 4

OPERATIONS

Basic operations

• Control panel .......................................... 6

• Remote controller (RM-RK230) ................ 7

Listening to the radio ................................ 10

Disc operations ......................................... 11

EXTERNAL DEVICES

Listening to the USB memory ..................... 19

Listening to the CD changer ....................... 20

Listening to the iPod®/D. player ................. 21

Listening to the other external

components .......................................... 22

Dual Zone operations ................................ 23

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

SETTINGS

Selecting a preset sound mode ................... 24

General settings — PSM ........................... 25

Disc setup menu ........................................ 28

Assigning names to the sources .................. 30

Maintenance ............................................ 31

More about this unit ................................. 32

Troubleshooting ....................................... 37

Specifications ........................................... 40

Introduction

Disc type Recording format, file type, etc Playable

DVD DVD-Video

DVD-Audio

DVD-ROM

DVD Recordable/Rewritable (DVD-R*1/-RW, +R/+RW*2)

DVD-RAM All

Dual Disc DVD side

CD/VCD Audio CD (CD-DA), DTS-CD

CD Recordable/Rewritable (CD-R/-RW)

• Compliant to ISO 9660 level 1, level 2, Romeo, Joliet

*1 DVD-R recorded in multi-border format is also playable (except for dual layer discs).

It is possible to play back finalized +R/+RW (Video mode only) discs. However, the use of +R double layer disc on this unit is not

recommended.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

Caution on volume setting

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

DVD-Video

DivX Video

MPEG-1/MPEG-2 Video

MP3/WMA/WAV

JPEG

DVD-VR, +VR

Non-DVD side

VCD (Video CD)

CD-Text

CD-ROM

CD-I (CD-I Ready)

CD-DA, DTS-CD

DivX Video, VCD (Video CD)

MPEG-1/MPEG-2 Video

MP3/WMA/WAV

JPEG

Note on Region Code:

DVD players and DVD Video discs have their own Region Code numbers. This unit can only play back DVD discs whose Region Code numbers include “5.”

If you insert a DVD Video disc of an incorrect Region Code

“REGION CODE ERROR!” appears on the monitor.

Before operating the unit — Cancel the display demonstration and set the clock

• See also page 26.

When the power is turned off: Check the current clock time When the power is turned on: Change the display information

~ Turn on the power. Ÿ Enter the PSM settings. ! ] ⁄ Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute.

Set the clock

@ Finish the procedure.

How to detach/attach the control panel

Detaching... Attaching...

Lever

CAUTION:

The lever comes out if you pressed the 0 button while the panel is detached. If this happens, push the lever back into lock position before attaching the panel.

Basic operations — Control panel

Select the source.

FM/AM = DISC* = USB* = CD-CH*/IPOD*/ D.PLAYER* (or EXT IN) = LINE IN =(back to the

beginning)

* You cannot select these sources if they are not ready.

• FM/AM: Select the bands.

• DISC: Start playback.

Change the display information

Detach the panel.

• FM/AM: Select preset station.

• DISC: Select chapter/title/folder/ track/disc (for CD changer).

• Turn on the power.

• Turn off the power [Hold].

• Attenuate the sound (if the power is on).

• Volume control [Turn]

USB input terminal

Select the sound mode.

Display window

Eject disc.

Adjust the sound mode.

Hold to enter the PSM settings.

Enter functions mode.

Press MODE, then one of the following buttons (within 5 seconds)...

MO: Turn on/off monaural reception. SSM: Automatic station presetting. DUAL: Activate/deactivate Dual Zone. RPT: Select repeat play. RND: Select random play.

5/∞: Skip 10 chapters/tracks.

• FM/AM: Search for station.

• DISC: Select chapter/track.

• IPOD/D.PLAYER: Select track.

• FM/AM: Select preset station.

• DISC: Select title/folder.

• IPOD/D.PLAYER: Enter the main menu/ Pause or stop playback/Confirm selection.

Display window

Main display

(Time, menu, playback information)

Source display/Preset No./ Track No./Folder No./ Disc No./Chapter No.

Tuner reception indicators

Dual Zone indicator

Track information indicators

Disc type indicators

Playback source indicators

Equalizer indicator

Sound mode indicators

• also functions as level meter (see also page 26).

Basic operations — Remote controller (RM-RK230)

Installing the lithium coin battery (CR2025)

Before using the remote controller:

• Aim the remote controller directly at the remote sensor on the unit.

• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).

Warning: To prevent accidents and damage

• Do not install any battery other than CR2025 or its equivalent.

• Store the battery in a place where children cannot reach.

• Do not recharge, short, disassemble, heat the battery, or dispose of it in a fire.

• Do not leave the battery with other metallic materials.

• Do not poke the battery with tweezers or similar tools.

• Wrap the battery with tape and insulate when throwing away or saving it.

Loudness indicator

Track indicator

Playback mode/item indicators (Random/Repeat)

Remote sensor

Continued on the next page

OPERATIONS

IMPORTANT:

If Dual Zone is activated (see page 23), the remote controller only functions for operating the DVD/CD player.

MONITOR CONTROL

1 Monitor control buttons

• Used for a JVC monitor—KV-MR9010 or KV-MH6510.

DVD/RECEIVER CONTROL

2 Turns on/off the power.

• Attenuates the sound if the power is on.

3 Selects the source. 4 Selects the FM/AM bands.

• DVD-Video/DivX: Shows disc menu.

• VCD: Starts PBC playback.

6 Activates or deactivates Dual Zone.

7 Adjusts the volume level.

• Also function as 2nd VOL when pressed with SHIFT button (see page 23)

8*1 Enters disc setup menu. 9 SHIFT button p 7 (stop), 3 (play), 8 (pause)

• 3 (play) also function as ZOOM button when pressed with SHIFT button (see page 14).

•

Not applicable for CD changer/iPod/ D. player operations.

q*2 For advanced disc operations:

•

/TITLE 5 / ∞

DVD-Video: Selects the titles.

DivX/MPEG Video/MP3/WMA/WAV: Selects the folders if included.

• 4 / ¢: Reverse skip/forward skip.

• 1 / ¡: Reverse search/forward search.

For FM/AM tuner operations:

• PRESET 5 / ∞

Changes the preset stations.

• 4 / ¢

Searches for the stations.

For Apple iPod

/JVC D. player

operations:

• 5 / ∞

∞: Pauses/stops or resumes playback. 5: Enters the main menu. (Now 5/∞/4 / ¢ work as the

menu selecting buttons.)*

• 4 / ¢ (in menu selecting mode)

– Selects an item if pressed briefly.

(Then, press ∞ to confirm the selection.)

– Skips 10 items at a time if pressed and

held.

• 4 / ¢

Press: Reverse skip/forward skip. Hold: Reverse search/forward search.

w • Shows the on-screen bar.

• Also function as the

/TITLE button when pressed with SHIFT button (see pages 13 and 14).

• DVD-Video/DivX: Shows disc menu.

• VCD: Starts PBC playback.

• Makes selection/settings.

• @ / #: DivX: Searches for index during play.

• DISC +/– buttons: Changes discs when the source is “CD-CH.”

RETURN button

y • DVD-Video: Selects audio language

(

), subtitles ( ), angle ( ).

• DivX: Selects audio language ( subtitles (

• VCD: Selects audio channel (

Functions as number buttons when pressed

with SHIFT button.

–

FM/AM: Selects preset stations.

–

DISC: Selects chapter/title/folder/track.

Functions as +10/–10/+100/–100 buttons

when pressed with SHIFT button.

5 : Returns to the previous menu.

∞ : Confirms the selection.

How to select a number

To select a number from 0 – 9:

To select a number greater than 9:

To select a number greater than 99 (for searching DivX/MPEG Video/MP3/WMA/ WAV tracks):

OPERATIONS

Listening to the radio

Change the display information

Select preset station.

* If no name is assigned to a station, “NO NAME”

appears. To assign a name to a station, see page 30.

~ Select “FM/AM.” Ÿ Select the bands.

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

! Search for a station to listen—Auto Search.

• Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.

When an FM stereo broadcast is hard to receive

Local FM stations with the strongest signals

are searched and stored automatically in the FM band.

Reception improves, but stereo effect will be

lost.

• MO indicator lights up.

FM station automatic presetting —SSM (Strong-station Sequential Memory)

You can preset six stations for each band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

Disc operations

Before performing any operations...

Turn on the monitor to watch the playback picture. If you turn on the monitor, you can also control playback of other discs by referring to the monitor screen. (See pages 15 – 18.) The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its internal program). If the current disc does not have any disc menu, all tracks will be played repeatedly until you change the source or eject the disc.

If “

” appears on the monitor when pressing a button, the unit cannot accept the operation you

have tried to do.

• In some cases, without showing “

Start playback if necessary.

,” operations will not be accepted.

Open the control panel and insert the disc.

Playback starts automatically.

Change the display information

Prohibiting disc ejection

To cancel the prohibition, repeat the same procedure.

*1 If the file does not have Tag information or

“TAG DISP” is set to “TAG OFF” (see page

27), folder name and file name appear. TAG indicator will not light up.

“NO NAME” appears for an audio CD.

Continued on the next page

OPERATIONS

Operations using the control panel

Pressing (or holding) the following buttons allows you to...

Disc type

Press: Select chapter Hold: Reverse/fast-forward

chapter*

Press: Select track Hold: Reverse/fast-forward track*

Select title During stop: Locate title

—

Select folder Locate particular folder directly

(Number buttons)

During play/pause: Locate chapter

Locate particular track directly (PBC not in use)

Press: Select track Hold: Reverse/fast-forward track

Press: Select track Hold: Reverse/fast-forward track*

*1 Search speed changes to on the monitor.

Search speed changes on the monitor.

After pressing

, press the following buttons to...

Select folder Locate particular folder directly

—

Disc type

Skip 10 chapters (during play or pause)

Skip 10 tracks (PBC not in use) TRK RPT: Repeat current track

Skip 10 tracks (within the same folder)

Skip 10 tracks TRK RPT: Repeat current track DISC RND: Randomly play all

• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”

CHP RPT: Repeat current

chapter

TIT RPT: Repeat current title

(PBC not in use)

TRK RPT: Repeat current track FLDR RPT: Repeat current folder —

TRK RPT: Repeat current track FLDR RPT: Repeat current folder

Locate particular track directly

—

DISC RND: Randomly play all

tracks (PBC not in use)

FLDR RND: Randomly play all

tracks of current folder, then tracks of next folders

DISC RND: Randomly play all

tracks

Operations using the remote controller—RM-RK230

: Stop play : Pause (Frame by frame playback if pressed during

pause.)

: Start play (10-second review if pressed during play.)

: Reverse/forward chapter search*1

• Slow motion during pause. No sound can be

: Press: Select chapter (during play or pause)

Hold: Reverse/fast-forward chapter search

: Select title : Select audio language : Select subtitle language : Select view angle

While holding ...*

: Select chapter (during play or pause)

Select title (when stop)

, then : Select title directly

Using menu driven features...

1 / 2 Select an item you want to start play.

heard.*

: Stop play : Pause (Frame by frame playback if

pressed during pause.)

: Start play

: Reverse/forward track search*1

• Slow motion during pause. No sound can be heard.*

• Reverse slow motion does not work.

: Press: Select track

Hold: Reverse/fast-forward track search

: Select audio channel (ST: stereo, L: left,

R: Right)

While holding ...*

: Select track (For VCD with PBC, a list of items

is shown on the disc menu.)

• To return to the previous menus, press .

Canceling the PBC playback...

1 2 While holding , press *

to start the

desired track.

• To resume PBC, press / .

Continued on the next page

OPERATIONS

+ 29 hidden pages

JVC KD-DV7203, KD-DV7204, KD-DV7205, KD-DV7206 Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual