ПРИЕМНИК ДЛЯ ВОСПРОИЗВЕДЕНИЯ
ДИСКОВ DVD И КОМПАКТ-ДИСКОВ
ПРИЙМАЧ З ПРОГРАВАЧЕМ DVD/CD-ДИСКІВ
KD-AVX77/KD-AVX55
Only for KD-AVX77
For canceling the display demonstration, see page 11.
Информацию об отмене демонстрации функций дисплея см. на стр. 11.
Інформацію щодо відміни демонстрації функцій дисплею див. на стор. 11.
For installation and connections, refer to the separate manual.
Указания по установке и выполнению соединений приводятся в отдельной инструкции.
Вказівки по встановленню та виконанню підключень наведені у окремій інструкції.
ENGLISHУКРАЇНАРУCCKИЙ
INSTRUCTIONS
ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
ІНСТРУКЦІЇ
LVT1938-005A
[EE]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
ENGLISH
2. CAUTION: Do not open the
top cover. There are no user
serviceable parts inside the unit;
leave all servicing to qualified
service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
WARNINGS:
(To prevent accidents and damage)
• DO NOT install any unit or wire any cable in a location
where;
– it may obstruct the steering wheel and gearshift
lever operations.
– it may obstruct the operation of safety devices
such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
If you need to operate the unit while driving, be sure
to look around carefully.
• The driver must not watch the monitor while driving.
• The driver must not put on the headphones while
driving.
• Excessive sound pressure from earphones or
headphones can cause hearing loss when you listen
through earphones or headphones using Dual Zone.
[European Union only]
Cautions on the monitor:
• The monitor built in this unit has been produced with
high precision, but it may have some ineffective dots.
This is inevitable and is not malfunction.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with the sharp tip.
Touch the buttons on the touch panel with your finger
directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
– Chemical changes occur inside, causing
malfunction.
– Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
• Afterimage may occur if displaying a certain
image on the monitor for a long time. This is not
malfunction. Turn off the unit or display another
image.
2
How to read this manual:
• < > indicates the variable screens/menus/
operations/settings that appear on the touch
panel.
• [ ] indicates the buttons on the touch panel.
• ( page number) indicates the reference
page number of the related topics/operations/
settings.
• Operation index: To locate easily the desired
operations/functions. (
•Indication language: English indications are
used for the purpose of explanation. You can
select the indication language in <Language>.
(
15)
• Illustrations: Illustrations of KD-AVX77 are
mainly used for explanation.
73)
How to reset your unit
• Your preset adjustments will also be erased (except the
registered Bluetooth devices for KD-AVX77, 32)
To forcibly eject a disc, 36.
For safety...
• Do not raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
CONTENTS
How to read this manual .............................. 3
How to reset your unit ................................. 3
INTRODUCTIONS
Playable disc type ........................................ 4
DTS-CD/SVCD (Super Video CD)/CD-ROM/
CD-I (CD-I Ready)
CD Recordable/Rewritable
(CD-R/-RW)
• ISO 9660 level 1, level 2, Romeo,
Joliet
CD-DA
VCD (Video CD)
DivX/MPEG1/MPEG2
JPEG
MP3/WMA/WAV/AAC*
MPEG4
*1 If you insert a DVD Video disc of an incorrect Region Code, “Region code error” appears on the screen.
*2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer discs are not
playable.
*3 It is possible to play back finalized +R/+RW (Video format only) discs. “DVD” is selected as its disc type when a
+R/+RW disc is loaded. +RW double layer discs are not playable.
*4 This unit cannot play back contents protected with CPRM (Content Protection for Recordable Media).
*5 This unit can play back AAC files encoded using iTunes.
Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the
use of Non-DVD side of a DualDisc on this product may not be recommended.
1
4
5
5
4
Basic operations
SRC
KEY
QUICK
MENU
Using the monitor panel/touch panel
Touch panel (see the following pages).
Most of the operations are explained using the touch panel
unless mentioned otherwise.
CD
SRC
01 02 0:01:20
Track Title
Artist Name
Disc Title
MP3
FLAT
ENGLISH
Monitor panel
15:45
USB cable from the rear of the unit, (
1 Displays AV Menu. ( 12)
2 Displays Source Menu.*
3 Bluetooth indicator (KD-AVX77 only)
4 • Turns on the power.
1
( 7)
• Attenuates the sound (if the power is on).
• Turns off the power. (Hold)
• Switches the conversation media while talking
with a Bluetooth cellular phone. (KD-AVX77
only, 49)
5 Remote sensor
6 Resets the unit. ( 3)
7 Detaches the monitor panel.
8 • Adjusts the volume.
• Adjusts the volume of the incoming calls. *
2
(KD-AVX77 only)
9 • Displays Open/Tilt screen. ( 6)
• Ejects the disc and displays Open/Tilt screen.
(Hold)
47, 51)
p Displays Quick Menu. ( 7)
q Changes the buttons shown on the touch panel.
( 6)
*1 Available sources depend on the external components
you have connected, media you have attached, and
the < > (input) settings you have made.
( 19)
*2 This adjustment does not affect the volume level of
the other sources.
Attaching the monitor panel
5INTRODUCTIONS
While a picture is played back on the screen, the
buttons and information on the touch panel are turned
off about 10 seconds after the last operation.
• You can select the way the buttons and information
are turned off in <Monitor/Sensor>. (
ENGLISH
The buttons and information turn on again:
– When your hand moves
closer to the touch panel
(depending on the
<Monitor/Sensor>
setting,
– When you press
– For KD-AVX77: When a call/SMS comes in for
Bluetooth cellular phone.
• The buttons and information may turn on in other
cases than the above.
Caution on volume setting:
Digital devices (CD/USB) produce very little noise
compared with other sources. Lower the volume
before playing these digital sources to avoid
damaging the speakers by sudden increase of the
output level.
You can also adjust the volume by moving your finger
as illustrated on any part of the touch panel.
20).
button on the monitor panel.
20)
Buttons on the touch panel
Each time you touch [KEY], the buttons shown on the
touch panel are changed.
Ex.: When “
• Available buttons vary among the sources.
• The background picture can be changed on the
TUNER
” is selected as the source
Operation buttons
<Wall Paper> setting. (
Source buttons
13)
Open/Tilt screen
When you drag your finger on the touch panel,
it functions in the same way as touching
[5 / ∞ / 4 / ¢].
• Touch the panel firmly when moving or
dragging your finger.
6
[Open]/
[Eject]
[Close]Closes the monitor panel.
[Tilt]Tilts the monitor panel.
[
• Shaded items cannot be used.
Opens the monitor panel./
Ejects the disc.
Closes this screen.
]
Source Menu
You can select a source on Source Menu.
Current source
Returns to the previous screen.
Quick Menu
You can easily access some frequently used functions by
using Quick Menu.
(connected with KS-PD100):
– Reverse skip/forward skip.
– Reverse search/forward search. (Hold)
In menu selecting mode:
– Selects an item. (Then, press ∞ to confirm the
: Cancels.
: Scrolls the displayed information once.
: Repeats scrolling (at 5-second intervals).
: Cancels.
: Shows the Tag data while playing MP3/WMA/WAV/AAC
tracks.
♦
Off
♦
On
♦
Auto
♦
Dimmer Time Set
: Cancels.
: Activates dimmer.
: Dims the monitor when you turn on the headlights. *
: Activates the Dimmer Time setting (see below).
)/Off( ) times.
♦
01 (bright), 02 (middle), 03 (dark)
♦
–15 to +15; Initial 00
2
You can adjust the following to make the screen clear and legible for watching the
playback picture. The setting will be stored—one for “
for “
iPod USB/AV-IN
.”
Touch [5] or [∞] to select an item, then touch [+] or [–] to adjust. (–15 to +15;
Initial 00)
♦
Bright
♦
Contrast
♦
Color
3
♦
Tint *
DISC/USB/iPod USB
AV-IN
” and the incoming signal is PAL, you cannot adjust this setting.
: Adjust if the picture is too bright or too dark.
: Adjust the contrast.
: Adjust the color of the picture—lighter or darker.
: Adjust the tint if the human skin color is unnatural.
” (the media must contain pictures or movies) or
DISC/USB
1
” and the other
14
Menu itemSelectable setting/item
4
Aspect *
You can change the aspect ratio of the picture.
Aspect ratio of the incoming signal
4:316:9
♦
16:9 FullSuitable for 16:9 picture.
♦
Ultra FullStretches the picture displayed in <16:9
Full> to the width of the screen.
♦
Cinema
Suitable for Cinemascope-size picture.
Scope
♦
Ultra
Cinema Sc.
Stretches the picture displayed in
<Cinema Scope> to the width of the
screen.
♦
ZoomSuitable for 4:3 Letterbox picture.
Display
♦
AutoAspect ratio is automatically selected to match the incoming signals.
Language *
Key PositionSelect the position of the buttons on the touch panel.
Dual Display
Time Set
Time FormatSelect either 12-hour system or 24-hour system.
OSD Clock
Clock
Clock AdjustSelect <Auto> to adjust the clock automatically using the clock time (CT) data
4
Not adjustable when no picture is shown.
*
*5 Turn off the power and on again so that your setting takes effect.
5
Select the indication language shown on the screen.
: Cancels.
: The clock time is displayed on the playback picture.
from an FM Radio Data System station.
♦
Off, Auto
ENGLISH
15AV MENU
ENGLISH
Menu itemSelectable setting/item
6, *7
6, *7
6, *7
6, *7
Select the initial disc menu language; Initial Руccĸий ( 64)
Select the initial audio language; Initial Руccĸий ( 64)
Select the initial subtitle language or erase the subtitle <Off>;
Initial Руccĸий ( 64)
Select the monitor type to watch a wide screen picture on the external
monitor.
♦
16:9
: Select when the aspect ratio of the external
monitor is 16:9.
♦
4:3 Letterbox,
4:3 Pan Scan
: Select when the aspect ratio of the external
monitor is 4:3.
Menu Language *
Audio Language *
Subtitle *
Monitor Type *
OSD Position *
File Type *
Disc
DivX Regist.
(Registration)*
Artwork
iPod Control *
6, *7
6, *7
6
9
Select the position of the on-screen bar. ( 42)
• The on-screen bar is not displayed fully under some <Aspect> settings.
(
15)
♦
1
♦
2
: Higher position.
: Lower position.
Select the playback file type when a disc/USB contains different types of
files. You can store this setting separately for each source—
“
DISC/USB
♦
Audio
♦
Still Picture
♦
Video
♦
Audio&Video
.”
: Plays back audio files.
: Plays back JPEG files.
: Plays back DivX/MPEG1/MPEG2 files.
: Plays back audio files and DivX/MPEG1/MPEG2
files.
This unit has its own Registration Code. Once you have played back a file
with which the Registration Code recorded, this unit’s Registration Code is
overwritten for copyright protection.
For “
DISC/USB
For “
iPod USB
”: “Jacket picture” is shown on the screen.*7 ( 37)
”: The Artwork is shown on the screen under “HEAD
MODE.”*8 ( 51)
♦
Off
♦
On
Changes the controlling unit for “
♦
Head
♦
iPod
: Cancels.
: Activates “Jacket picture” or Artwork display.
iPod USB
.” ( 51)
: Controls the iPod/iPhone through this unit.
: Controls the iPod/iPhone through the iPod/
iPhone.
16
Menu itemSelectable setting/item
D. (Dynamic)
Range Compres.
(Compression)*
Speaker Size *
Disc
Speaker Level *
You can enjoy a powerful sound at a low volume level while playing Dolby Digital
software on a disc.
7
♦
Auto
: Select to apply the effect to multi-channel encoded
software.
♦
On
6, *7
You can adjust the speaker size setting.
♦
Front speakers: Small, Large
♦
Center speaker: None, Small, Large
♦
Rear speakers: None, Small, Large
♦
Subwoofer: On, Off
: Select to always use this function.
• Speaker size: <Large> for 13 cm diameter or more; <Small> for 13 cm or less.
• Front speakers and rear speakers: left and right speakers cannot be adjusted
separately.
Regardless of the setting above...
• No sound comes out of the subwoofer while playing Dolby Pro Logic II Movie or
Music if the front speaker is set to <Large>.
• No sound comes out of the center speaker when surround is deactivated.
( 21)
6
You can adjust the output level of the activated speakers (above), monitoring the
test tone.
ENGLISH
1 Front speakers
2 Center speaker
3 Rear speakers
4 Subwoofer
Adjust the output level of each speaker in the range of –10dB to +10dB; Initial
00dB
• Touch [TEST] to turn on the test tone. To stop, touch [CANCEL].
• Subwoofer level setting takes effect only when surround is activated. ( 21)
6
Selectable only for “
*
DISC/USB
.”
*7 Playback stops when you change the setting.
*8 It takes 5 seconds or more to display Artwork and no operations are available while loading it.
*9 Selectable only for “
iPod USB
.”
Continued on the next page
17AV MENU
Menu itemSelectable setting/item
Speaker Distance *6You can adjust the output timing of the activated speakers (above).
ENGLISH
Disc
Adjust the speaker distance from the listening position in the range of 15 cm/
6 inch to 600 cm/240 inch in 15 cm/6 inch step; Initial 120 cm/48 inch (for
center speaker), 150 cm/60 inch (for front and rear speakers).
• Touch [cm/inch] to change the measuring unit—cm and inch.
IF Band Width
AF Regional *
Tuner
TA Standby *
TA Volume You can adjust the preset TA volume level.
6
17
*
*10 Not available when AM/FM3 is selected as the band.
*11 Depends on the amplifier gain control. ( 24)
10
♦
Auto
♦
Wide
10
You can change the Network-Tracking Reception setting. ( 35)
When the received signals from the current station become weak...
♦
Off
♦
AF Regional
♦
AF
♦
Off
♦
On
When the unit switches to Traffic Announcement (TA), the volume changes to the
preset TA volume level if the current volume level is lower than the preset level.
(
35)
♦
00 to 30 or 50*11, Initial 15
: Increases the tuner selectivity to reduce interference
noises between adjacent stations. (Stereo effect may be
lost.)
: Subject to the interference from adjacent stations, but
sound quality will not be degraded and the stereo effect
will remain.
: Cancels—not selectable when <DAB AF> is set to
<On>.
: Switches to another station broadcasting the same
programme. The REG indicator lights up.
: Switches to another station. The programme may differ
from the one currently received (the AF indicator lights
up). (
35)
: Cancels.
: Activates TA Standby Reception. ( 35)
18
Menu itemSelectable setting/item
Program Search
DAB AF *
Tuner
AV Input *
12
13
You can turn on and off the Programme Search. (
♦
Off
♦
On
: Cancels.
: Activates the Programme Search.
You can turn on and off the Alternative Frequency Reception. ( 55)
♦
Off
♦
On
: Cancels.
: Activates the Alternative Frequency Reception.
You can determine the use of LINE IN and VIDEO IN plugs. ( 56)
♦
Off
: Select when no component is connected (“
not displayed on Source Menu).
♦
iPod(Off)
: Select when connecting the iPod/iPhone using the USB
Audio and Video cable for iPod/iPhone. ( 51)
♦
Audio&Video
: Select when connecting an AV component such as a
VCR.
♦
Input
External Input *
Audio
♦
Camera *
♦
Navigation
16
For connecting an external component to the CD changer jack on the rear.
: Select when connecting an audio component such as a
14, *15
portable audio player.
: Select when connecting a rear view camera.
: Select when connecting a Navigation System.
• For connecting the DAB tuner, this setting is not required. The DAB tuner is
automatically detected.
♦
Changer/iPod *
♦
External
12
Selectable only when DAB tuner is connected. ( 54)
*
*13 Not selectable when “
AV-IN
” is selected as the source.
17
: CD changer, (
: Any other than the above, ( 57).
*14 The REVERSE GEAR SIGNAL lead connection is required. See Installation/Connection Manual. The rear view through
the camera appears on the screen in <16:9 FULL> aspect ratio (regardless of the aspect ratio setting) when you
shift the gear to the reverse (R) position. When you shift the gear to another position other than the reverse (R)
position, the rear view screen is cleared.
*15 While the pictures through the camera are shown on the monitor, no message will be displayed.
*16 Not selectable when the component connected to the CD changer jack is selected as the source.
*17 The name of the component detected through the CD changer jack is shown.
35)
53), iPod, ( 52).
AV-IN
” is
ENGLISH
19AV MENU
ENGLISH
Other
Menu itemSelectable setting/item
Beep
Telephone Muting *
Monitor/SensorYou can turn off the buttons and information shown on the touch panel or turn
♦
18
Off
♦
On
♦
Off
♦
Muting1,
Muting2
: Cancels.
: Activates the key-touch tone.
: Cancels.
: Select either one which mutes the sounds while using
the cellular phone.
off the touch panel when no operation is done for about 10 seconds. (
Normal/
Motion
While a picture is played back
on the screen
Buttons and information light up
when your hand moves closer to
the touch panel.
Others
Buttons and
information always
light.
Normal/Touch Buttons and information light up
when you touch the touch panel.
WallPaper/
Motion
WallPaper/
Touch
Buttons and information light up when your hand moves
closer to the touch panel.
Buttons and information light up when you touch the touch
panel.
Off/MotionThe touch panel lights up when your hand moves closer to it.
Off/TouchThe touch panel lights up when you touch it.
6)
Motion Sensitiv.
(Sensitivity)
Change the sensitivity of the sensor for <Monitor/Sensor> (above).
♦
Mid, High
InitializeInitialize all settings you have made in AV Menu. Hold [Enter] to initialize the
settings, then reset the unit. (
18
Connection to the cellular phone system is required. See Installation/Connection Manual.
*
3)
20
You can enjoy multi-channel surround playback through the front, center, surround speakers.
MULTI:
For multi-channel encoded sources such as Dolby Digital. (When activated, “MULTI” is shown on the screen.)
Dolby Pro Logic II (Movie/Music):
For 2 channel sources except for DivX/MPEG1/MPEG2 discs.
• After connecting the center speaker, make sure to activate the center speaker; otherwise, no sound comes out of
the center speaker. (
• You cannot activate this function in the following cases:
– When “
iPod USB
– When Dual Zone is in use.
17)
” is selected as the source.
Turning on the surround
1 Select <Disc Surround> on AV Menu.
2 Turn on the surround.
Turn on the surround (1), then touch
<Auto> to show the surround modes (2).
3 Select a surround mode.
<Auto>:
• When multi-channel digital signals come in,
“MULTI” surround is activated.
• When 2-channel or 2.1-channel signals*
come in, 4-channel stereo is activated.
<Through>:
All incoming channel signals are sent to the
corresponding speakers.
<Dolby PLII Movie>:
Activates Dolby Pro Logic II Movie.
<Dolby PLII Music>:
Activates Dolby Pro Logic II Music. You can
adjust <Panorama> and <Center Width>
settings. ( 22)
* Except signals of DivX/MPEG1/MPEG2 discs.
ENGLISH
Continued on the next page
21AV MENU
On the remote:
ENGLISH
Changing the <Dolby PLII Music> setting
In step 3 on page 21...
1 Select <Dolby PLII Music>.
2 Select desired settings.
<Panorama>:
Select <On> to add wraparound sound effect.
<Center Width>*:
Adjust the center image so it may be heard
only from the center speaker, only from
the left/right front speaker as a “phantom”
center image, or various combination of
these speakers. As the number increases, the
“phantom” effect becomes stronger (normally
set to <04>).
* Adjustable when the center speaker is
activated. ( 17)
3 Finish the procedure.
• You cannot change the <Dolby PLII Music>
settings using the remote controller.
22
Select a preset sound mode suitable to the music genre.
♦
Flat (Initial), Hard Rock, R&B, Pop, Jazz, Dance, Country, Reggae, Classic, User1, User2, User3
• (For “
DISC/USB
VCD, or MP3/WMA/WAV/AAC files and <Auto> is selected for <Surround Mode>. ( 21)
”) While surround is activated, you can use Equalizer in the following case: the source is CD-DA,
You can store your adjustments into <User1>, <User2>, and <User3>.
1 Select <Equalizer> on AV Menu.
2 Make the setting, then store.
Moves to the other 6 sound modes.
Touch [2] or [3] to select a frequency level
to adjust.
Touch [5] or [∞] to adjust.
15.0 kHz
Ex.: When storing into <User1>.
Moving each bar directly also makes adjustments.
23AV MENU
Initial: Underlined
Menu itemSelectable setting/item
Fader/Balance
Fader:
ENGLISH
Adjust the front and rear
speaker output balance.
Balance:
Adjust the left and right
speaker output balance.
Volume Adjust *
1
Subwoofer Level
High Pass Filter
CrossoverSelect the crossover frequency between the front/rear speakers and the
Amplifier Gain *
Rear Speaker *
*1 For “
2
3
DISC/USB
”: You can make the adjustments separately depending on the audio format—Dolby digital and
the others.
*2 The volume level automatically changes to “30” if you change to <Low Power> with the volume level set higher
than “30.”
3
*
This setting takes effect only when Dual Zone is activated. ( 43)
♦
F06 to R06; Initial 00 (fader)
♦
L06 to R06; Initial 00 (balance)
[5/∞]: Adjusts fader.
[2/3]: Adjusts balance.
[]: Resets the adjustments.
• When using a two-speaker system, set the fader to the center (00).
Adjust and store the auto-adjustment volume level for each source, comparing
to the FM volume level. The volume level will automatically increase or decrease
when you change the source.
• <Fix> appears when an FM broadcast is selected as the source.
♦
–12 to +12; Initial 00
You can adjust the output level of the subwoofer when it is activated.(
♦
–06 to +08; Initial 00
♦
Through
♦
On
: Select when the subwoofer is not connected.
: Select when the subwoofer is connected.
subwoofer.
♦
80Hz, 120Hz, 150Hz
You can change the maximum volume level of this unit.
♦
Off
♦
Low Power
: Deactivates the built-in amplifier.
: VOL 00 to 30 (Select this if the maximum power of the
speakers is less than 50 W.)
♦
High Power
: VOL 00 to 50
You can activate/deactivate the rear speakers.
♦
Off, On
Dragging also makes
adjustments.
17)
24
Selectable items when the source is:
•
TUNER
•
•
•
•
: Mono*1, SSM, PTy Standby*1, PTy Code*
DAB
DISC, USB, CD-CH, iPod, Bluetooth
iPod USB
AV-IN, EXT-IN
: D. (Dynamic) Range Control, Announce Standby, Announce
Code, PTy Standby, PTy Code
2
:
*
Repeat, Random
: Repeat, Random, AudioBooks
: Title Entry
Menu itemSelectable setting/item
1
Mono*
SSM (Strong-station
Sequential Memory)
PTy Standby*
1
PTy Code*
D. (Dynamic) Range
Control
Announce Standby
Announce Code
1
*
Not available when FM3 is selected as the band.
*2 KD-AVX77 only
When an FM stereo broadcast is hard to receive, activate monaural mode for better
reception.
♦
Off
♦
On
: Restores the stereo effect.
: Activates monaural mode to improve FM reception, but stereo effect
will be lost. The MONO indicator lights up.
You can automatically preset 6 stations for each FM band.
• Local FM stations with the strongest signals are searched and stored automatically in the
FM band.
1
You can turn on and off the PTY Standby Reception. ( 35)
♦
Off
♦
On
: Cancels.
: Activates the PTY Standby Reception.
Selects the PTY code for the PTY Standby Reception. ( 34, 35)
Some DAB services provide Dynamic Range Control (DRC) signals together with their
regular programme signals. DRC will reinforce the low level sounds to improve your
listening.
♦
Off: Cancels.
♦
DRC1, DRC2, DRC3
: As the number increases, the effect becomes stronger.
You can turn on and off the Announce Standby Reception. ( 55)
♦
Off
♦
On
: Cancels.
: Activates the Announce Standby Reception.
Selects the announcement type for the Announce Standby Reception. (
♦
Transport News, Warning, News, Weather, Event, Special Event, Radio Info,
Sports News, Financial News
Initial: Underlined
1
ENGLISH
(Hold)
55)
Continued on the next page
25AV MENU
Menu itemSelectable setting/item
RepeatAvailable items depend on the types of loaded disc and playback file.
ENGLISH
RandomAvailable items depend on the types of loaded disc and playback file.
AudioBooks *
Title EntryYou can assign titles (up to 16 characters) to “
♦
Chapter
♦
Title
♦
Program
: Repeats current chapter.
: Repeats current title.
: Repeats current program (For DVD-VR, not available during Playlist
playback).
♦
Disc
♦
Folder/Group*
♦
Track
♦
One
♦
All
♦
Off
♦
Folder/Group*
: Repeats all tracks of the current disc.
3
: Repeats all tracks of the current folder/group.
: Repeats current track. (For VCD: When PBC is not in use.)
: Functions the same as “Repeat One” of the iPod/iPhone.
: Functions the same as “Repeat All” of the iPod/iPhone.
: Cancels.
3
: Randomly plays all tracks of the current folder/group, then tracks
of the next folders/groups.
♦
Disc/USB
♦
All
♦
Song
♦
Album
♦
Off
5
You can select the playback speed of the audiobook sound file in your iPod/iPhone.
♦
Normal
♦
Faster
♦
Slower
: Randomly plays all tracks. (For VCD: When PBC is not in use.)
: Randomly plays all tracks of all loaded discs.
: Functions the same as “Shuffle Songs” *4 of the iPod/iPhone.
: Functions the same as “Shuffle Albums” of the iPod/iPhone.
: Cancels.
: Plays at normal speed.
: Plays faster.
: Plays slower.
AV-IN
” and “
characters, 63.)
EXT-IN
.” (For available
[5/∞]: Changes the character one by one.
[2/3]: Moves the cursor.
[SPACE]: Enters a space.
[CHANGE]: Changes the character set.
[STORE]: Confirms the entry.
[CLEAR]: Erases all entered characters.
*3 KD-AVX77 only
*4 You can activate <Shuffle Songs> in <Search Mode> menu. ( 28)
*5 Not selectable when connecting the iPod with the interface adapter. ( 52)
26
SourceOperation/setting
TUNER/DAB• Storing a preset station/service manually
1 Touch [BAND], then [ / ] to tune in to the station/service you want to preset.
2 Touch [ ], then [List].
3 Select a preset number.
Ex.: When storing an FM station
(Hold)
ENGLISH
The station selected in step 1 is now stored in preset number 4.
Touch to select the band.
• Selecting a preset station/service on the list
Ex.: When selecting an FM preset station
DISC/USBSelecting a track on the list
If a disc/device includes folders, you can display the Folder/Track (File) Lists, then start
playback.
Touch/drag to browse the Lists.
1 Current folder list
number/total folder list
number
2 Current track list
number/total track list
number of the current
folder
Continued on the next page
27AV MENU
SourceOperation/setting
iPod USBSelecting a track/video from <Search Mode>*
ENGLISH
♦
Music
♦
Videos
♦
Shuffle Songs
CD-CHSelecting a disc on the list
: Playlists, Artists, Albums, Songs, Podcasts, Genres,
Composers, Audiobooks
: Video Playlists, Movies, Music Videos, TV Shows, Video
Podcasts
: Starts playback.
Touch/drag to browse the List.
1
1 Current track list
number/total track list
number of the current
folder
• If currently played MP3 disc is selected, Folder List appears. Track List also appears by
selecting the current folder. ( 27) Select a track to start playback.
1
You can enter <Search Mode> menu when “HEAD MODE” is selected.
*
Available search modes depend on the type of your iPod/iPhone.
For Dual Zone operations, 43.
28
(KD-AVX77 only)
• Firstly, use <New Pairing> in <Device Menu> to register and establish the connection with a device.
Menu itemSelectable setting/item
Dial Menu *1*
1
Only for the device connected for Bluetooth phone.
*
*2 You can display the last opened menu in <Dial Menu> by pressing on the remote controller.
You can display <Redial> by holding on the remote controller.
*3 You can also activate it by holding [ ].
2
Select a calling method, then select the desired item to call.
♦
Redial
♦
Received Calls
♦
Phonebook
♦
Preset Calls
♦
Phone Number
: Shows the list of the phone numbers you have dialed.
: Shows the list of the received calls.
: Shows the phone book copied from a cellular phone. ( 31)
: Shows the list of the preset numbers. ( 50)
: Shows the phone number entry screen.
[BS]: Erases the last character.
[Dial]: Calls the entered number.
[Preset]: Goes to <Preset Memory>. You can preset the entered number by selecting
a preset number.
♦
Voice Dialing*
3
: Available only when the connected cellular phone has the
voice recognition system = Speak the name you want to call.
To delete the phone numbers/names
1 Touch [Delete] when <Redial>, <Received Calls>, or <Phonebook> in <Dial Menu> is displayed.
2 Select the phone number/name you want to delete.
• Touch [All] to delete all the numbers/names in the selected item.
3 Touch [Yes] to confirm deleting.
• To cancel, touch [No].
ENGLISH
Continued on the next page
29AV MENU
Menu itemSelectable setting/item
ENGLISH
Phone Connect*4/
Audio Connect*
Phone Disconnect*
Audio Disconnect*
Delete PairingOnly for the registered devices.
New PairingPreparation:
Only for the registered devices.
4
Select a device from among the registered devices, establish the connection
with it.
4
/
Only for the device being connected.
4
Disconnect the current device before connecting another device.
Touch [Yes] to confirm deleting the registered devices.
• Operate the Bluetooth device to turn on its Bluetooth function.
1 Enter a PIN (Personal Identification Number) *
5
.
• You can enter any number you like (1-digit to 16-digit number).
Device Menu
[BS]: Erases the last character.
[Enter]: Confirms the entry.
2 Operate the Bluetooth device to connect while “Open...” is displayed on
the screen.
Enter the same PIN code (as entered in the above step) on the device to
be connected.
Now connection is established and you can use the device through the unit.
• The device remains registered even after you disconnect the device. Use
<Phone Connect>/<Audio Connect> (or activate <Auto Connect>,
31) to connect the same device from next time.
4
When a device is not connected to the unit, <Phone Connect> and <Audio Connect> appear. When a device
*
has already been connected to the unit, <Phone Disconnect> and <Audio Disconnect> appear.
30
Menu itemSelectable setting/item
Auto Connect When the unit is turned on, the connection is established automatically
with...
♦
Off
♦
Last
Auto Answer
SMS Notify
♦
Off
♦
On
♦
Reject
♦
Off
♦
On
Add PhonebookYou can copy the phone book memory of a cellular phone into the unit.
1 Enter a PIN (Personal Identification Number) .*
Settings
• You can enter any number you like (1-digit to 16-digit number).
[BS]: Erases the last character.
[Enter]: Confirms the entry.
2 Operate the target cellular phone.
Enter the same PIN code (as entered in the above step) on the cellular
phone then transfer the phone book memory to the unit. (Refer to the
instruction manual supplied with your cellular phone.)
3 Touch [] to finish the procedure.
• If you try to copy a 101st phone book entry, “Phonebook Full” appears on
the monitor. Delete unwanted names before copying. (
5
Some devices have their own PIN code. Enter the specified PIN code to the unit.
*
: No Bluetooth device.
: The last connected Bluetooth device.
: The unit does not answer the calls automatically.
Answer the calls manually.
: The unit answers the incoming calls automatically.
: The unit rejects all incoming calls.
: The unit does not inform you of the arrival of a
message.
: The unit informs you of the arrival of a message by
ringing and displaying “Receiving Message.”
ENGLISH
5
29)
Continued on the next page
31AV MENU
Menu itemSelectable setting/item
MIC SettingAdjust the volume of the microphone connected to the unit.
Phone VolumeAdjust the phone volume.
ENGLISH
InitializeYou can initialize all settings you have made in <Bluetooth>.
Settings
InformationThe following information is shown:
6
*
Depends on the amplifier gain control. ( 24)
*7 If you wish to receive more information about Bluetooth, visit the following JVC web site:
: The unit name
: The Mac address of the unit
: The Bluetooth software/hardware versions*
: The connected device names
7
32
Listening to the radio
ENGLISH
~ Touch [SRC], then select “TUNER.”
Ÿ Touch [BAND].
! Touch [ ] or [ ] to search for a
station—Auto Search.
• Manual Search: Hold either [ ]or [ ] until
“Manual Search” appears on the screen, then
touch it repeatedly.
• The ST indicator lights up when receiving an
FM stereo broadcast with sufficient signal
strength.
A Band
B Preset number
C Sound mode
D PS (station name) for FM Radio Data System.
E PTY code for FM Radio Data System
F Tuner/Standby Reception indicators
Selectable frequency of FM:
– FM1, FM2: 87.5 MHz to 108.0 MHz
– FM3: 65.00 MHz to 74.00 MHz
Selecting a preset station
• To preset stations into memory, 25, 27.
Directly from the touch panel
• You can also select a preset station using the remote controller (
You can display the Preset List by holding [5 / ∞].
If no PS signal is coming in, “No Name” appears.
( 34)
9, 10) and from the Preset List ( 27).
• To improve the FM reception, 25.
• To use convenient functions for FM Radio Data System stations, 34.
33OPERATIONS
The following features are available only for FM Radio Data System stations.
Searching for FM Radio Data System programme—PTY Search
You can search for your favorite programmes being broadcast by selecting the PTY code for your favorite
programmes.
ENGLISH
1 Display <PTy Search> menu.
2 Select a PTY code.
• You can select a PTY from 29 PTY codes.
PTY Search starts.
If there is a station broadcasting a programme
of the same PTY code as you have selected, that
station is tuned in.
Available PTY codes:
News, Current Affairs, Information, Sport, Education, Drama, Cultures, Science, Varied Speech, Pop Music, Rock
Music, Easy Listening, Light Classics M, Serious Classics, Other Music, Weather & Metr, Finance, Children’s Progs,
Social Affairs, Religion, Phone In, Travel & Touring, Leisure & Hobby, Jazz Music, Country Music, National Music,
Oldies Music, Folk Music, Documentary
Moves to the other 6 PTY codes.
34
Activating/deactivating TA/
PTY Standby Reception
TA Standby ReceptionIndicator
To activate, touch [QUICK MENU],
then
.
The unit will temporarily switch to
Traffic Announcement (TA) if available,
from any source other than AM/FM3.
• The volume changes to the preset
TA volume level if the current level is
lower than the preset level. (
Not yet activated. Tune in to another
station providing the Radio Data
System signals.
To deactivate, touch [QUICK MENU],
.
then
TP
Lights up
18)
Flashes
Goes off
Tracing the same programme
—Network-Tracking
Reception
When driving in an area where FM reception is not
sufficient enough, this unit automatically tunes in to
another FM Radio Data System station of the same
network, possibly broadcasting the same programme
with stronger signals.
Programme A broadcasting on different frequency
areas (01 – 05)
ENGLISH
PTY Standby ReceptionIndicator
To activate, touch [QUICK MENU],
then
.
The unit will temporarily switch to
your favorite PTY programme from any
source other than AM/FM3.
Not yet activated. Tune in to another
station providing the Radio Data
System signals.
To deactivate, touch [QUICK MENU],
then .
• When a DAB tuner is connected, TA Standby/PTY
Standby Reception also works for the DAB tuner and
searches for the services.
To change the PTY code for PTY Standby Reception,
25.
PTY
Lights up
Flashes
Goes off
When shipped from the factory, Network-Tracking
Reception is activated.
To change the Network-Tracking Reception
setting, see <AF Regional>. (
• When the DAB tuner is connected, refer also to
“Tracing the same programme—Alternative
Frequency Reception (DAB AF).” (
18)
55)
Automatic station selection—
Programme Search
Usually when you select preset stations, the preset
station is tuned in.
If the signals from the preset FM Radio Data System
station are not sufficient for good reception, this
unit, using the AF data, tunes in to another station
broadcasting the same programme as the original
preset station is broadcasting. To activate this function,
select <On> for <Program Search>.( 19)
• The unit takes some time to tune in to another
station using programme search.
35OPERATIONS
Disc operations
The disc type is automatically detected, then playback starts (for some discs, the top menu of the disc appears).
If a disc does not have any disc menu, all tracks on it will be played repeatedly until you change the source or eject
the disc.
ENGLISH
” appears on the screen, the unit cannot accept the operation you have tried to do.
If “
• In some cases, without showing “ ,” operations will not be accepted.
~ Open the monitor panel.
• By holding [ ], you can open the
monitor panel and eject the disc.
Ÿ Insert a disc.
Monitor panel closes automatically.
• If not, touch [Close].
Playback starts automatically.
Caution:
Do not place your finger behind the monitor
panel.
Label side
How to forcibly eject a disc
(Hold)
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit. ( 3)
36
(Hold)
Prohibiting disc ejection
You can lock a disc in the loading slot.
(Hold)
(Hold)
To cancel the prohibition, repeat the same
procedure to select <EJECT OK?>.
Operation buttons and information on the touch panel
Operation buttons and information are shown on the touch panel.
• While watching playback pictures, you can display the buttons and information by touching the touch panel or
moving your hand nearby. ( 20)
Ex.: While playing a DVD Video
• While MP3/WMA/AAC file
is played, “Jacket picture”
is shown if the file has the
tag data including “Jacket
picture.” ( 16)
ENGLISH
1 [5 / ∞]
• DVD Video/DVD-VR: Selects title/program/
playlist.
• DivX/MPEG1/MPEG2/JPEG/MP3/WMA/WAV/
AAC:
– Selects folder
– Displays Folder/Track List (Hold)
1 While holding SHIFT, press DIRECT repeatedly to select the desired search mode.
DVD-Video:
DVD-VR:
Start play/Pause (if pressed
during play)
1
• Select track
• Reverse/fast forward track
search *3 (Hold)
—
DivX/MPEG1/MPEG2:
JPEG:
MP3/WMA/WAV/AAC:
VCD/CD:
2 While holding SHIFT, press the number buttons (0 – 9) to enter the desired number.
3 Press ENT (enter) to confirm.
40
• For DivX/MPEG1/MPEG2/JPEG/MP3/WMA/WAV/AAC,
track is searched within the same folder.
• For DVD-VR, program/playlist search is possible
during Original program playback (PG)/Playlist
playback (PL).
• To erase a misentry, press CLR (clear) while holding
SHIFT.
Using menu driven features
• DVD Video
1 Press TOP M/MENU to enter the menu screen.
2 Press % / fi / @ / # to select an item you want to
start play.
3 Press ENT (enter) to confirm.
• DVD-VR
1 Press TOP M to enter the Original Program.
Press MENU to enter the Playlist.
2 Press % / fi / @ / # to select an item you want to
start play.
3 Press ENT (enter) to confirm.
• Original Program/Playlist screen, 59.
• VCD
1 While holding SHIFT, press DIRECT to enter the
search mode.
2 While holding SHIFT, press the number buttons (0
– 9) to enter the desired number.
3 Press ENT (enter) to confirm.
• To return to the previous screen, press RETURN.
Canceling the PBC playback (VCD)
1 Press , then press DIRECT while holding SHIFT.
2 While holding SHIFT, press the number buttons
(0 – 9) to enter the desired number.
3 Press ENT (enter) to confirm.
• To resume PBC, press TOP M/MENU.
Operations using the
on-screen bar
(DVD-Video/DVD-VR/DivX/MPEG1/MPEG2/
JPEG/VCD)
These operations are possible on the monitor using the
remote controller.
1 Show the on-screen bar. ( 42)
(twice)
• The on-screen bar is not displayed fully under
some <Aspect> settings. (
2 Select an item.
3 Make a selection.
If pop-up menu appears...
• To cancel pop-up menu, press RETURN.
• For entering time/numbers, see the following.
Entering time/numbers
Press % / fi to change the number, then press @ / # to
move to the next entry.
• Each time you press % / fi, the number increases/
decreases by one value.
• After entering the numbers, press ENT (enter).
• It is not required to enter the zero and tailing zeros
(the last two digits in the example below).
Ex.: Time search
DVD: _:_ _:_ _ (Ex.: 1:02:00)
Press % once, then # twice to go to the third entry, %
twice, then press ENT (enter).
15)
ENGLISH
Removing the on-screen bar
41OPERATIONS
On-screen bar
Ex.: DVD-Video
ENGLISH
Information
Operation
1 Disc type
2 • DVD-Video: Audio signal format type and
channel
• VCD: PBC
3 Playback mode *
1
DVD-Video: T. RPT: Title repeat
C. RPT: Chapter repeat
DVD-VR: C. RPT: Chapter repeat
PG. RPT: Program repeat
DivX/MPEG1/MPEG2:
T. RPT: Track repeatF. RPT: Folder repeatA. RND: All (Disc) randomF. RND: Folder random
JPEG: F. RPT: Folder repeat
VCD *2: T. RPT: Track repeat
A. RND: All (Disc) random
4 Playback information
Current title/chapter
5 Time indication
Current program/chapter
Current playlist/chapter
Current track
Current folder/track
Current folder/file
Elapsed playing time of the disc
(For DVD-Video, elapsed playing
time of the current title/program/
playlist.)
DVD-Video/DVD-VR: Remaining
title/program/playlist time
VCD: Remaining disc time
Elapsed playing time of the current
chapter/track *
3
Remaining time of the current
chapter/track *
6 Playback status
3
Play
Forward/reverse search
Forward/reverse slow-motion
Pause
Stop
7 Operation icons
Change time indication (see 5)
Time Search (Enter the elapsed
playing time of the current title/
program/playlist or of the disc.)
Title Search (by its number)
Repeat play * Random play *
Chapter Search (by its number)
Track Search (by its number)
1
1
Change the audio language, audio
stream, or audio channel
Change or turn off the subtitle
language
Change the view angle
*1 For repeat play/random play, 26.
*2 While PBC is not in use.
*3 Not applicable for DVD-VR.
42
Using divided screens—Dual Display
A playback picture and the navigation screen/rear view screen can be displayed at the same time.
Preparation:
Make sure the following settings.
• <On> is selected for <Dual Display>. ( 15)
• <Navigation> or <Camera> is selected for <AV Input>. ( 19)
ENGLISH
While watching a playback picture on the screen, the navigation or rear view*
• You can swap the position of the screens in <Key Position>.
( 15)
To deactivate, select <Off> for <Dual Display>.
1
Only when the signal comes in
*
1
screen is displayed at the same time.
Playback picture
Navigation screen or
rear view screen
Dual Zone operations
You can enjoy disc playback on the external monitor connected to the VIDEO OUT and 2nd AUDIO OUT plugs, while
listening to any source other than “
• When Dual Zone is in use, you can only operate the DVD/CD player using the remote controller.
~ Select <Dual Zone> on AV Menu.
Ÿ Activate Dual Zone.
<Off>:
Deactivates Dual Zone.
<On>:
Activates Dual Zone without Headphone
Surround. The DUAL ZONE ON indicator lights
up.
<On/Surround On>:
Activates Dual Zone with Headphone
Surround*2. The DUAL ZONE SR ON indicator
lights up.
USB
” through the speakers.
*2 JVC original headphone virtual surround system.
This surround will also work for the main source
“
DISC
” if <On/Surround On> is selected. This
surround does not work for DivX/MPEG1/MPEG2
discs.
Continued on the next page
43OPERATIONS
On the remote:
1
ENGLISH
2
Adjust the volume through the 2nd
AUDIO OUT plug.
• The volume level is shown on the connected
external monitor.
3 Operate the DVD/CD player.
To select a different source (main source) to
listen to through the speakers
Touch [SRC], then select a source.
• By using the touch panel, you can operate the
newly selected source without affecting Dual Zone
(Disc) operations.
• You cannot select “USB” for the main source.
Operations using the control
screen
For discs except DVD and VCD:
While Dual Zone is on, these operations are possible on
the external monitor using the remote controller.
The control screen automatically appears when you
insert a disc. (For DivX/MPEG1/MPEG2/JPEG; while not
playing.)
Ex.: MP3/WMA
1 Current folder (highlighted bar)
2 Current folder no./total folder no.
3 Folder list
* If tag data includes “Jacket Picture” (baseline
JPEG), it will be displayed. If you press OSD, the
playback mode selection window appears. (
45)
4 Selected playback mode ( 45)
5 Elapsed playing time of the current track (not
displayed for JPEG)
6 Operation status
7 Current track no./total number of tracks in the
current folder (total number of tracks on the disc)
8 Track information (only for MP3/WMA/WAV/AAC)
9 Track list
p Current track (highlighted)
To select a folder or track
1 Select “Folder” column or “Track” column
on the control screen.
44
2 Select a folder or track.
• If necessary, press 6 to start playback.
Ex.: CD Text
Selecting playback modes
You can also change the playback modes using the
playback mode selection window.
• For JPEG, Random cannot be selected.
1
Except for JPEG: Select a playback mode.
2
3Select your desired option.
ENGLISH
1 The playback mode selection window: appears
when OSD is pressed (see the right).
2 Selected playback mode (see the right).
3 Elapsed playing time of the current track
4 Operation status
5 Current track number/total number of tracks on the
disc
6 Track information
7 Track list
8 Current track (highlighted bar)
To select a track
• If necessary, press 6 to start playback.
4
Selectable playback mode
• DivX/MPEG1/MPEG2/JPEG: ( 42)
• MP3/WMA/WAV/AAC:
– T. RPT: Track repeat
– F. RPT: Folder repeat
– F. RND: Folder random
– A. RND: All (Disc) random
• CD:
– T. RPT: Track repeat
– A. RND: All (Disc) random
45OPERATIONS
Operations using the list
screen
For discs other than DVD, VCD, and CD
While Dual Zone is on, these operations are possible on
the external monitor using the remote controller.
ENGLISH
While playback is stopped...
1 Display the list screen.
Using Dual Display
While Dual Zone is on, the main source (other than
“
USB
”) and “
DISC
” can be displayed at the same
time.
• Dual Display works while watching a playback picture
on the external monitor.
Preparation:
Make sure <On> is selected for <Dual Display>.
(
15)
2 Select a folder on the list.
3 Select a track on the list.
• To go back to the folder list, press RETURN.
1 Current folder number/total folder number
2 Current track number/total number of tracks in the
current folder
3 Current page/total number of the pages included
in the list
4 Current folder/track (highlighted bar)
Playback picture
(“
DISC
”)
To deactivate, select <Off> for <Dual Display>.
Main source
46
USB operations
You can connect a USB mass storage class device such as a USB memory, Digital Audio Player, portable HDD, etc. to
the unit.
• You can also connect the iPod/iPhone to the USB terminal of the unit. For details of the operations, 51.
USB cable from the rear of the unit
USB
The source changes to “
” and playback starts.
ENGLISH
This unit can play JPEG/MPEG1/MPEG2 *1/MP3/WMA/
WAV/AAC *2 files stored in USB mass storage class
device.
• You can operate the USB device in the same way you
operate the files on discs. ( 37 – 43)
• You cannot select “
• All tracks in the USB device will be played repeatedly
until you change the source.
*1 Except for MPEG2 files recorded by JVC Everio
camcorder (extension code <.mod>).
*2 This unit can play back AAC files encoded using
iTunes. This unit cannot play back FairPlay-encrypted
files.
USB
” when Dual Zone is in use.
Cautions:
• Avoid using the USB device if it might hinder your
safety driving.
• Do not pull out and attach the USB device repeatedly
while “Now Reading” is shown on the screen.
• Do not start the car engine if a USB device is
connected.
• Stop playback before disconnecting a USB device.
• Electrostatic shock at connecting a USB device may
cause abnormal playback of the device. In this case,
disconnect the USB device then reset this unit and the
USB device.
• This unit may not be able to play the files depending
on the type of USB device.
• Operation and power supply may not work as
intended for some USB devices.
• You cannot connect a computer to the USB ( )
terminal of the unit.
• Make sure all important data has been backed up to
avoid losing the data.
• Do not leave a USB device in the car, expose to direct
sunlight, or high temperature to avoid deformation
or cause damages to the device.
• Some USB devices may not work immediately after
you turn on the power.
• For more details about USB operations, 61.
47OPERATIONS
Using the Bluetooth® devices (KD-AVX77 only)
ENGLISH
Bluetooth is a short-range wireless radio communication technology for the mobile device such as mobile phones,
portable PCs, and other devices. The Bluetooth devices can be connected without cables and communicate with each
other.
• Refer to the list (included in the box) to see the countries where you may use the Bluetooth® function.
Bluetooth profile
This unit supports the following Bluetooth profiles;
• HFP (Hands-Free Profile) 1.5
• OPP (Object Push Profile) 1.1
• A2DP (Advanced Audio Distribution Profile) 1.2
• AVRCP (Audio/Video Remote Control Profile) 1.3
Connecting a new Bluetooth device
Connecting a Bluetooth device for the first time
When you connect a Bluetooth device to the unit for the first time, make pairing between the unit and the device.
Pairing allows Bluetooth devices to communicate each other.
To make pairing, you may need to enter the PIN (Personal Identification Number) code of your Bluetooth device you
want to connect.
• Once the connection is established, it is registered in the unit even if you reset the unit. Up to 5 devices can be
registered in total.
• Only one device for Bluetooth phone and one for Bluetooth audio can be connected at a time.
• To use the Bluetooth function, you need to turn on Bluetooth function of the device.
Use <New Pairing> in <Bluetooth> menu to register and establish the connection with a new device.
( 30)
To connect/disconnect/delete a device, 30.
Bluetooth Information:
If you wish to receive more information about Bluetooth, visit the following JVC web site:
<http://www.jvc.co.jp/english/car/> (English website only)
48
Using the Bluetooth cellular phone
To make a call, use <Dial Menu>. ( 29)
When a call comes in...
The source is changed to “
When <Auto Answer> is activated...
The unit answers the incoming call automatically.
31)
(
When <Auto Answer> is deactivated...
To answer the incoming call
Touch the message displayed on the touch panel.
To end the call
Hold the message displayed on the touch panel.
• You can adjust the microphone volume, 32.
Answering a waiting call
If your cellular phone is equipped with the call waiting
function, you can put the current call on hold and
answer the waiting call.
Touch any button on the touch panel (except volume
+/– buttons).
• To restore the on-hold call, touch any button on the
touch panel (except volume +/– buttons) again.
• When you end one call, you can connect to the other.
Bluetooth
Name and phone number (if
acquired)
” automatically.
Switching conversation media (the unit/
cellular phone)
During a phone call conversation...
ENGLISH
Each time you press the
button, the conversation
media alternates between the
unit ( ) and cellular phone
( ).
Then, continue your conversation using the selected
media.
When an SMS comes in...
If the cellular phone is compatible with SMS (Short
Message Service), the unit tells you a message has been
received. ( 31)
To read a received message, operate the cellular
phone after stopping the car in a safe place.
• You cannot read, edit, or send a message through
the unit.
Continued on the next page
49EXTERNAL DEVICES
Presetting the phone numbers
You can preset up to 6 phone numbers.
1 Display <Redial>, <Received Calls>,
<Phonebook>, or <Phone Number>.
( 29)
ENGLISH
2 Select a telephone number to store.
3 Select a preset number.
Now “Tom” is stored into preset no. 1.
To call a preset number, 29.
Using the Bluetooth audio player
(Hold)
~ Touch [SRC], then select “Bluetooth.”
Ÿ Touch [ 6 ] to start playback.
[6]:Starts playback.
5 / ∞]:Selects group/folder.
[
4 / ¢]:
[
[
7]:
• Some Bluetooth devices may not be controlled by the
buttons.
50
• Reverse/forward skip
• Reverse /forward search (Hold)
Pauses.
A Sound mode
B Connected device type indication
C Status of the device: Signal strength/Battery remainder
(only when the information comes from the device)
D Track no./Playing time (only for devices that support the
function)
E Tag data* (current track title/artist name/album title) if it
is recorded (only for devices that support the function)
* “No Name” appears when the Tag data is not recorded
or when the device does not support the function.
• To connect a new device, 30.
• To select the playback mode, 26.
Listening to the iPod/iPhone devices
You can connect the iPod/iPhone using the following cable or adapter:
ToCable/adapterTo operate
Listen to the
music
Watch the video USB Audio and Video cable for iPod/iPhone, KS-U30
• When watching the video on the external monitor, connect a monitor compatible with both NTSC and PAL.
When connected with the USB cable
The operations explained below are under “HEAD MODE.”
USB 2.0 cable (accessory of the iPod/iPhone) to the
USB cable from the rear of the unit.
Interface Adapter for iPod, KS-PD100 (not supplied)
to the CD changer jack on the rear of the unit.
(not supplied) to the USB cable from the rear of the
1
unit.*
See “When connected with the USB cable”
below.
See “When connected with the interface
adapter” (
See “When connected with the USB cable”
below.
52).
• The Artwork of the song is
shown if the song has an
Artwork data. ( 16)
ENGLISH
~ Touch [SRC], then select “iPod .”
Playback starts automatically.
• When you connect the iPod/iPhone to the
USB terminal, “
source and playback starts automatically.
• To change the controlling unit, touch
[QUICK MENU] then .
– HEAD MODE: Controls through this unit.
– iPod MODE*
iPod USB
” is selected as the
1
: Controls through the
connected iPod/iPhone.
Ÿ Touch [4] or [¢] to select a track/
video.
• You cannot resume playback for video sources.
• To select track/video from <Search Mode>, 28.
• To select the playback mode, 26.
• To change the play speed of the audiobooks,
• You can also change the controlling unit in <iPod Control>. ( 16)
[6]:Starts playback/pauses.
5 / ∞]:• Moves to the previous/next item of
[
[
4 / ¢]: • Reverse/forward skip *
A The controlling unit for playback ( 16 )
B Sound mode
*1 Make sure <iPod(Off)> is selected for <AV Input>
when using KS-U30 to connect. ( 19, 62)
*2 [5 / ∞] may not function depending on how you
select the current track/video.
*3 [4 / ¢] functions otherwise under “iPod
MODE.”
26.
a category. *
• Enters <Search Mode> menu.
(Hold) ( 28 )
• Reverse /forward search (Hold)
2
3
51EXTERNAL DEVICES
When connected with the interface adapter
ENGLISH
Preparation:
Make sure <iPod> is selected for <External Input>.
(
19)
~ Touch [SRC], then select “iPod.”
Playback starts automatically.
Ÿ Touch [4] or [¢] to select a track.
Selecting a track from the player’s
menu
1 Touch [] to enter the player’s menu.
The SEARCH indicator lights up.
• This mode will be canceled if no operations are
done for about 5 seconds.
2 Touch [4] or [¢] to select the desired
item.
• Skips 10 items at a time if there are more than
10 items. (Hold)
Playlists Ô Artists Ô Albums Ô
Songs Ô Genres Ô Composers Ô
(back to the beginning)
[
6]:Starts playback/pauses.
[
[
4 / ¢]: • Reverse/forward skip
Enters player’s menu.
]:
• Reverse /forward search (Hold)
4 Repeat steps 2 and 3 to select a track.
• When a track is selected finally, playback starts.
• To return to the previous menu, touch [].
To select the playback mode, 26.
3 Touch [6] to confirm the selection.
52
Listening to the CD changer
It is recommended to use a JVC MP3-compatible CD changer with your unit.
• You can play only CDs (CD-DA) and MP3 discs.
Preparation:
Make sure <Changer> is selected for <External Input>. (
Ex.: While playing an MP3 disc
19)
ENGLISH
~ Touch [SRC], then select “CD-CH.”
Ÿ Touch [ ].
! Touch [List].
⁄ Select a disc to start playing.
[4 / ¢]: • Reverse/forward skip
• Reverse /forward search (Hold)
(MP3 only)
5 / ∞]:• Selects folder.
[
• Displays Disc List. (Hold)
A Disc no.
B Sound mode
C Folder no./Track no./Playing time
D Current folder name/current file name, or tag data
(current track title/artist name/album title) if it is
recorded
• To select the playback mode, 26.
• To select an MP3 track from the Folder/Track List,
27.
53EXTERNAL DEVICES
Listening to the DAB tuner
ENGLISH
~ Touch [SRC], then select “DAB.”
Ÿ Touch [BAND].
! Touch [ ] or [ ] to search for an
ensemble—Auto Search.
• Manual Search: Hold either [ ] or [ ] until
“Manual Search” appears on the screen, then
touch it repeatedly.
⁄ Touch [FUNC] to select [ ], then touch
[
5] or [∞] to select a service (either
primary or secondary) to listen to.
[FUNC]:Changes items to select with [5 / ∞].
– : Services
– : Preset services ( 27)
Touch to display DLS.
A Band
B Preset number
C Sound mode
D Service label/Emsemble label
E PTY code
F DAB indicators
*1 If no signal is received, “No DAB Signal” appears.
*2 While tuning in a service with DLS (Dynamic Label
Segment), the TEXT indicator lights up.
• You can also display DLS by pressing DISP button
on the remote controller.
• To improve your listening when surrounding
sounds are noisy, try to adjust <D. Range Control>. ( 25)
• To activate/deactivate TA/PTY Standby
Reception, 35. (Operations are exactly the
same as the ones for FM Radio Data System
stations.)
• To search for your favorite programmes, 34.
2
*
/Standby Reception indicators
1
*
54
Activating/deactivating
Announcement Standby
Reception
Announcement Standby Reception allows the
unit to switch temporarily to your favorite service
(announcement type).
Announcement Standby Reception Indicator
To activate, touch [QUICK MENU], then
.
The unit will temporarily switch to your
favorite service from any source other
than FM/AM.
Not yet activated. Tune in to another
service providing the related signals.
To deactivate, touch [QUICK MENU],
then .
To change the announcement type for
Announcement Standby Reception, 25.
ANN
Lights up
Flashes
Goes off
Tracing the same
programme—Alternative
Frequency Reception (DAB
AF)
• While receiving a DAB service:
When driving in an area where a service cannot
be received, this unit automatically tunes in to
another ensemble or FM Radio Data System station
broadcasting the same programme.
• While receiving an FM Radio Data System
station:
When driving in an area where a DAB service is
broadcasting the same programme as the FM Radio
Data System station, this unit automatically tunes in
to the DAB service.
When shipped from the factory, Alternative Frequency
Reception is activated.
To deactivate the Alternative Frequency
Reception, select <Off> for <DAB AF>. (
19)
ENGLISH
55EXTERNAL DEVICES
Using other external components
AV-INPUT
You can connect an external component to the LINE IN/VIDEO IN plugs.
ENGLISH
• When watching the video on the external monitor, connect a monitor compatible with both NTSC and PAL.
~ Touch [SRC], then select “AV-IN.”
A Sound mode
B Assigned title (
26)
Ÿ Turn on the connected component and
start playing the source.
While watching the playback picture:
If no operation is done for about 10 seconds, the operation buttons disappear. ( 20)
Navigation screen
You can also connect a Navigation System to the VIDEO
IN plug so that you can watch the navigation screen.
It is always displayed regardless of the selected source.
Preparation:
Make sure <Navigation> is selected for <AV
Input>. ( 19)
• The aspect ratio of the navigation screen is fixed to
<16:9 Full> regardless of the <Aspect> setting.
( 15)
To display another screen
Using Dual Display, the navigation screen and playback
picture can be displayed at the same time.
Select <On> for <Dual Display> ( 15), then play
back a disc. ( 43)
When <Navigation> is selected for <AV Input>
( 19)
• You can use the source “
an audio source connected to the LINE IN plugs.
AV-IN
” for listening to
56
EXT-INPUT
You can connect an external component to the CD changer jack on the rear using the Line Input Adapter, KS-U57 (not
supplied) or AUX Input Adapter, KS-U58 (not supplied).
ENGLISH
A Sound mode
B Assigned title (
Preparation:
Make sure <External> is selected for <External
Input>. ( 19)
26)
~ Touch [SRC], then select “EXT-IN.”
Ÿ Turn on the connected component and
start playing the source.
57EXTERNAL DEVICES
Maintenance
Caution on cleaning the unit
Do not use any
ENGLISH
solvent (for example,
thinner, benzine,
etc.), detergent, or
insecticide. This may
damage the monitor or the unit.
Recommended cleaning method:
Gently wipe the panel with a soft, dry cloth.
How to clean the connector
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton
swab or cloth moistened
with alcohol, being
careful not to damage the
connectors.
Connectors
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture evaporates.
How to handle discs
When removing a disc from its case, press down the
center holder of the case and lift the disc out, holding it
by the edges.
• Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc in its case,
gently insert the disc around the center
holder (with the printed surface facing
up).
• Make sure to store discs in their cases after use.
Center holder
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If such
a disc is used, this unit may reject the disc.
To remove these rough spots, rub the
edges with a pencil or ball-point pen, etc.
Do not use the following discs:
Single CD (8 cm disc)Warped disc
Sticker and sticker residueStick-on label
Unusual shape
Transparent or semi-
transparent parts on its
recording area
C-thru Disc (semi-
transparent disc)
58
More about this unit
Tuner (FM only)
Storing stations in memory
• When SSM is over, received stations are preset in
no. 1 (lowest frequency) to no. 6 (highest frequency).
Disc
General
• In this manual, words “track” and “file” are
interchangeably used.
• This unit can only play back audio CD (CD-DA) files if
different type of audio files (MP3/WMA/WAV/AAC)
are recorded on the same disc.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
Inserting a disc
• When a disc is inserted upside down or has no
playable files, “Cannot play this disc Check the disc”
appears on the screen. Eject the disc.
Ejecting a disc
• If “No Disc“ appears after removing a disc, insert a
disc or select another playback source.
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
Playing DVD-VR
• When selecting an item from the Playlist, the item is
automatically played back repeatedly. To change to
another item, select it from the Playlist.
• For details about DVD-VR format and playlist, refer
to the instructions supplied with the recording
equipment.
Original Program/Playlist screen
• Original Program
• Playlist
ENGLISH
Playing Recordable/Rewritable discs
• This unit can recognize a total of 5 000 files and 250
folders (a maximum of 999 files per folder).
• Use only “finalized” discs.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• This unit can recognize a total of 25 characters for
file/folder names.
• Some discs or files may not be played back due to
their characteristics or recording conditions.
1 Original Program/Playlist number
2 Recording date
3 Recording source (TV station, the input terminal of
the recording equipment, etc.)
4 Start time of recording
5 Title of the program/playlist *
6 Highlight bar (current selection)
7 Creating date of playlist
8 Total number of chapters included in the playlist
9 Playback time
* The title of the original program or playlist may not be
displayed depending on the recording equipment.
59REFERENCES
File playback
Playing DivX files
• This unit can play back DivX files with the extension
code <.divx>, <.div>, or <.avi> (regardless of the
letter case—upper/lower).
ENGLISH
• Audio stream should conform to MP3 or Dolby Digital.
• The file encoded in the interlaced scanning mode
may not be played back correctly.
• The maximum bit rate for video signals (average) is
4 Mbps.
Playing MPEG1/MPEG2 files
• This unit can play back MPEG1/MPEG2 files with the
extension code <.mpg>, <.mpeg>, or <.mod>*.
* <.mod> is an extension code used for the MPEG2 files
recorded by JVC Everio camcorders. The MPEG2 files
with the <.mod> extension code cannot be played
back when stored on a USB mass storage class device.
• The stream format should conform to MPEG system/
program stream.
The file format should be MP@ML (Main Profile at
Main Level)/SP@ML (Simple Profile at Main Level)/
MP@LL (Main Profile at Low Level).
• Audio streams should conform to MPEG1 Audio
Layer-2 or Dolby Digital.
• The maximum bit rate for video signals (average) is
4 Mbps.
Playing JPEG files
• This unit can play back JPEG files with the extension
code <.jpg>, or <.jpeg>.
• This unit can play back JPEG files that are at 32 x 32 to
8 192 x 7 680 resolution. It may take time to display
the file depending on its resolution.
• This unit can play back baseline JPEG files.
Progressive JPEG files or lossless JPEG files cannot be
played.
Playing MP3/WMA/WAV/AAC files
• This unit can play back files with the extension
code <.mp3>, <.wma>, <.wav>, or <.m4a>
(regardless of the letter case—upper/lower).
• This unit can play back the files meeting the
conditions below:
• This unit can play back files recorded in VBR (variable
bit rate).
• Files recorded in VBR have a discrepancy in elapsed
time indication.
60
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– AAC files encoded by using any other application
than iTunes.
– AAC files copy-protected with FairPlay (except
those stored on an iPod/iPhone).
– Files which have the data such as AIFF, ATRAC3,
etc.
Enjoying surround sounds
• If <Surround> is set to <On>, “MULTI” surround
playback automatically starts for multi-channel
encoded discs regardless of the <Surround Mode>
setting.
• You cannot activate surround for MPEG multi-channel
DVD Video, DivX 2-channel and MPEG 2-channel
sources. If <Surround> is set to <On>, stereo
sounds are emitted only through the front speakers.
“FRONT 2ch” appears on the source information
screen.
• When “FIX” appears on the source information
screen, no sound comes out of the subwoofer.
• When <Auto> is selected, downsampling is
performed for DVD Video (LPCM only) and DVD-VR
(LPCM only).
USB
• If “No USB Device“ appears after removing a device,
reattach a device or select another playback source.
• When the USB device has no playable files, or has not
been formatted correctly, “Cannot play this device
Check the device” appears on the screen.
• This unit cannot recognize a USB device whose rating
is other than 5 V and exceeds 500 mA.
• While playing from a USB device, the playback order
may differ from other players.
• This unit may be unable to play back some USB
devices or some files due to their characteristics or
recording conditions.
• USB devices equipped with special functions such as
data security functions cannot be used with the unit.
• Do not use a USB device with 2 or more partitions.
• Depending on the shape of the USB devices and
connection ports, some USB devices may not be
attached properly or the connection might be loose.
• When connecting a USB device, refer also to its
instructions.
• Connect only one USB device to the unit at a time. Do
not use a USB hub.
• This unit may not recognize a memory card inserted
into a USB card reader.
• When connecting with a USB cable, use the USB 2.0
cable.
• This unit may not play back files in a USB device
properly when using a USB extension cord.
• This unit cannot assure proper functions or supply
power to all types of the devices.
• This unit can recognize a total of 5 000 files and 250
folders (a maximum of 999 files per folder).
• This unit can recognize a total of 25 characters for
file/folder names.
• For MPEG1/MPEG2 files: The maximum bit rate for
video signals (average) is 2 Mbps.
ENGLISH
61REFERENCES
Bluetooth operations (KD-AVX77
only)
General
• While driving, do not perform complicated operation
such as dialing the numbers, using phone book, etc.
ENGLISH
When you perform these operations, stop your car in
a safe place.
• Some Bluetooth devices may not be connected to
this unit depending on the Bluetooth version of the
device.
• This unit may not work for some Bluetooth devices.
• Connecting condition may vary depending on
circumstances around you.
• When the unit is turned off, the device is
disconnected.
Warning messages for Bluetooth operations
• Connection Error:
The device is registered but the connection has failed.
Use <Phone Connect> or <Audio Connect> to
connect the device again. ( 30)
• Error:
Try the operation again. If “Error” appears again,
check if the device supports the function you have
tried.
• Please Wait...:
The unit is preparing to use the Bluetooth function. If
the message does not disappear, turn off and turn on
the unit, then connect the device again (or reset the
unit).
Icons for phone types
• These icons indicate the phone type set on the device.
: Cellular phone
: Household phone
: Office
: General
: Other than above
iPod/iPhone operations
• You can control the following types of iPod/iPhone:
(A) Connected with the USB cable:
– iPod with video (5th Generation) *1, *2, *
– iPod classic *1, *
– iPod nano *2, *
– iPod nano (2nd Generation) *
(B) Connected with the interface adapter:
– iPod with Click Wheel (4th Generation)
– iPod mini
– iPod photo
– iPod with video (5th Generation)
– iPod classic
– iPod nano
– iPod nano (2nd Generation)
– iPod nano (3rd Generation)
– iPod nano (4th Generation) *
4
*1 To watch the video with its audio, connect the iPod/
iPhone using USB Audio and Video cable (KS-U30, not
supplied).
*2 “iPod MODE” is available, 51.
*3 To listen to the sound in “iPod MODE,” connect the
iPod/iPhone using USB Audio and Video cable (KSU30, not supplied).
*4 It is not possible to charge the battery through this
unit.
• If the iPod/iPhone does not play correctly, update
your iPod/iPhone software to the latest version.
For details about updating your iPod/iPhone, visit
<http://www.apple.com>.
• When you turn on this unit, the iPod/iPhone is
charged through the unit.
• The text information may not be displayed correctly.
• The text information scrolls on the monitor. This
unit can display up to 40 characters when using the
interface adapter and up to 128 characters when
using the USB 2.0 cable or USB Audio and Video
cable.
3
2
2
2
62
Notice:
When operating an iPod/iPhone, some operations may
not be performed correctly or as intended. In this case,
visit the following JVC web site: <http://www.jvc.
co.jp/english/car/> (English website only)
For the USB connection:
When <Artwork> is set to <On>:
Do not press any buttons during the first 5 seconds or
more of playing back any track containing an Artwork*.
It takes 5 seconds or more to display an Artwork and no
operations are available while loading it.
* The picture displayed on the screen of the iPod/iPhone
while playing back a track
Characters you can enter for titles
In addition to the roman alphabet (A – Z, a – z), you
can use the following characters to assign titles. (
26)
• When <Руccĸий> is selected for <Language>.
( 15)
Upper and lower cases
ENGLISH
JVC bears no responsibility for any loss of
data in an iPod/iPhone and USB mass storage
class device while using this unit.
CD changer
• If you select a folder, which does not include any
music files, on the list (
Select another folder including music files.
28), you will hear a beep.
DAB tuner
• Only the primary DAB service can be preset even
when you store a secondary service.
Menu settings
• If you change the <Amplifier Gain> setting
from <High Power> to <Low Power> while
the volume level is set higher than “30,” the unit
automatically changes the volume level to “30.”
• After you change any of <Menu Language/Audio Language/Subtitle> settings, turn off then on the
power, and re-insert the disc (or insert another disc)
so that your setting takes effect.
• When you select <16:9> for a picture whose aspect
ratio is 4:3, the picture slightly changes due to the
process for converting the picture width.
• Even if <4:3 Pan Scan> is selected, the screen size
may become <4:3 Letterbox> for some discs.
Numbers and symbols
• When any language other than <Руccĸий> is
selected for <Language>. (
Upper and lower cases
Numbers and symbols
15)
63REFERENCES
Language codes (for DVD/DivX language selection)
Code Language Code Language Code Language Code Language Code Language
About sounds reproduced through the rear terminals
• Speaker out/analog discrete output—LINE OUT (FRONT/REAR)/CENTER OUT/SUBWOOFER OUT: Multi-channel
signals are emitted for a multi-channel encoded software. (When Dual Zone is activated, the same signal
emitted through 2nd AUDIO OUT plugs are emitted for the main source “
• 2nd AUDIO OUT: 2-channel signal is emitted when Dual Zone is activated. When playing a multi-channel
encoded disc, multi-channel signals are downmixed.
• Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of
Dolby Laboratories.
• “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other
countries.
• DivX® is a registered trademark of DivX, Inc., and is used under license.
• Plays DivX® video
• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified or DivX Ultra
Certified device that plays DivX video.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX® Certified device must be registered in order to play DivX Video-onDemand (VOD) content. First generate the DivX VOD registration code for your device and submit it during the
registration process. [Important: DivX VOD content is protected by a DivX DRM (Digital Rights Management)
system that restricts playback to registered DivX Certified devices. If you try to play DivX VOD content not
authorized for your device, the message “Authorization Error” will be displayed and your content will not play.]
Learn more at www.divx.com/vod.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Victor
Company of Japan, Limited (JVC) is under license. Other trademarks and trade names are those of their respective
owners.
• “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance standards.
• “Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and
has been certified by the developer to meet Apple performance standards.
• Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
• iPod and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.
• iPhone is a trademark of Apple Inc.
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
DISC
.”)
ENGLISH
65REFERENCES
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
• For operations with the external components, refer also to the instructions supplied with the adapters used for the
connections (as well as the instructions supplied with the external components).
ENGLISH
• Messages (enclosed in “ ”) in the tables below are shown in the language selected on <Language>. ( 15)
Messages described here are in the language of this manual.
SymptomRemedy/Cause
• No sound comes out of the speakers. • Adjust the volume to the optimum level.
• Check the cords and connections.
• DTS sound cannot be reproduced through any terminals
(Speaker out/LINE OUT).
• No sound comes out of the center
speaker.
• The screen is not clear and legible.Sunshine from the windshield may cause this symptom.
• “Mecha Error Push Reset” appears on
the screen, and the panel does not
move.
• “No Signal” appears.• Change the source.
General
•
button on the monitor panel
does not work.
• The unit does not work at all.
• The remote controller does not work.
• The touch panel does not respond
properly.
• <Monitor/Sensor> does not work
properly.
• Center speaker is not activated. (
the unit, make sure to activate the speaker again.
• Center speaker is used only for surround playback. No sound
comes out for stereo playback.
Adjust <Bright>. (
Reset the unit. (
• Start the playback on the external component connected to
VIDEO IN plug.
• Check the cords and connections.
• Signal input is too weak.
When the monitor panel is open, the button does not function.
Reset the unit. (
Deactivate Dual Zone. (
the remote controller only functions for operating the DVD/CD
player.)
• Keep your hands and the touch panel clean and dry.
• Eliminate static electricity and do not place conductors or any
materials generating static electricity near the unit.
• Leave the unit until the temperature becomes stable in the car.
• A rubber mat on the floor may cause this symptom. In this case,
do not use the rubber mat.
14)
3)
3)
17) Once you have reset
43) (While Dual Zone is activated,
66
SymptomRemedy/Cause
• SSM automatic presetting does not
work.
Tuner
• Static noise while listening to the
radio.
• Disc can be neither recognized nor
played back.
• Disc cannot be ejected.
• Recordable/Rewritable discs cannot
be played back.
• Tracks on the Recordable/Rewritable
discs cannot be skipped.
• Playback does not start.• Insert the disc correctly again.
• The playback picture is not clear and
legible.
• Sound and pictures are sometimes
interrupted or distorted.
Disc in general
• No playback picture is shown and
“Parking Brake” appears on the
screen, even when the parking brake
is engaged.
• No picture appears on the external
monitor.
• “Eject Error” or “Loading Error”
appears on the screen.
• “Region code error” appears on the
screen when you insert a DVD Video.
Store stations manually. (
Connect the aerial firmly.
Eject the disc forcibly. (
Unlock the disc. (
• Insert a finalized disc.
• Finalize the discs with the component which you used for
recording.
• The format of files is not supported by the unit.
Adjust items in <Picture Adjust> menu. (
• Stop playback while driving on rough roads.
• Change the disc.
Parking brake lead is not connected properly.
See Installation/Connection Manual.
• Connect the video cord correctly.
• Select the correct input on the external monitor.
• Change the source.
• Change the disc.
Region code is not correct. (
36)
27)
ENGLISH
36)
14)
4)
67REFERENCES
SymptomRemedy/Cause
• Disc cannot be played back.• Change the disc.
ENGLISH
• Noise is generated.The track played back is not a playable file format. Skip to another
• Tracks are not played back as you
have intended them to play.
• Elapsed playing time is not correct.This sometimes occurs during playback. This is caused by how the
• “Not Support” appears on the screen
DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC
and track skips.
• Noise is generated.The track played back is not a playable file format. Skip to another
• Tracks cannot play back as you have
intended them to play.
• “Now Reading...” keeps flashing on
the screen.
USB
• Correct characters are not displayed
(e.g. album name).
• While playing a track, sound is
sometimes interrupted.
• Bluetooth device does not detect the
unit.
• The unit does not make pairing with
the Bluetooth device.
• Echo or noise occurs.Adjust the microphone position.
Bluetooth (KD-AVX77 only)
• Record the tracks using a compliant application on the
appropriate discs. ( 4)
• Add appropriate extension codes to the file names.
file.
Playback order may differ from the one played back using other
players.
tracks are recorded.
The track is unplayable.
file.
Playback order may differ from the one played back using other
players.
• Readout time varies depending on the USB device.
• Do not use too many hierarchy and folders.
• Turn off the power and on again.
For available characters, 63.
The tracks are not properly copied into the USB device. Copy
tracks again, and try again.
• Search from the Bluetooth device again.
• Reset the unit. While “Open...” is shown on the screen, search
from the Bluetooth device again.
• Enter the same PIN code for both the unit and target device. If
the PIN code of the device is not indicated on its instructions,
try “0000” or “1234.”
68
Symptom
• Phone sound quality is poor.• Reduce the distance between the unit and the Bluetooth
cellular phone.
• Move the car to place where you can get a better signal
reception.
• The sound is interrupted or skipped
while using a Bluetooth audio player.
• The connected audio player cannot
be controlled.
• The unit does not response when you
Bluetooth (KD-AVX77 only)
tried to copy the phone book to the
unit.
• “No Audio Device” appears on the
screen.
• “No Voice Device” appears on the
screen.
• The iPod/iPhone does not turn on or
does not work.
• Sound is distorted.Deactivate the equalizer either on this unit or the iPod/iPhone.
• Playback stops.The headphones are disconnected during playback. Restart
iPod/iPhone
• “Cannot play this device Check the
device” appears on the screen.
• No operations are available when
playing back a track containing
Artwork.
• “Restricted Device” appears on the
screen.
• Reduce the distance between the unit and the Bluetooth audio
player.
• Disconnect the device connected for Bluetooth phone.
• Turn off, then turn on the unit.
• (When the sound is not yet restored) connect the player again.
Check whether the connected audio player supports AVRCP
(Audio Video Remote Control Profile).
You may have tried to copy the same entries (as stored) to the
unit.
Connect this unit and the Bluetooth audio player correctly.
The connected cellular phone does not have the voice recognition
system.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery of the iPod/iPhone.
• Check whether “HEAD MODE” or “iPod MODE” is correctly
selected. (
• Reset the iPod/iPhone.
playback.
No tracks are stored. Import tracks to the iPod/iPhone.
Operate the unit after the Artwork is loaded. (
Check whether the connected iPod/iPhone is compatible with this
unit. (
62)
Remedy/Cause
16, 51)
16, 63)
ENGLISH
Continued on the next page
69REFERENCES
ENGLISH
iPod
CD changer
DAB tuner
AV-IN
SymptomRemedy/Cause
• “Disconnect” appears on the screen. Check the connection.
• “Reset01” – “Reset07” appears on
the screen.
• “Reset08” appears on the screen.Check the connection between the adapter and this
• The control of iPod does not work
Only when connecting with
the interface adapter
after disconnecting from this unit.
• “No Disc” appears on the screen.Insert a disc into the magazine.
• “No Magazine” appears on the screen.Insert the magazine.
• “Cannot play this disc Check the disc” appears
on the screen.
• “Reset08” appears on the screen.Connect this unit and the CD changer correctly and press
• “Reset01” – “Reset07” appears on the screen. Press the reset button of the CD changer.
• The CD changer does not work at all.
• “No DAB Signal” appears on the screen.Move to an area with stronger signals.
• “Reset 08” appears on the screen.Connect this unit and the DAB tuner correctly, then reset
• The DAB tuner does not work at all.Connect this unit and the DAB tuner correctly, then reset
• “Antenna Power NG” appears on the screen.Check the cords and connections.
• No picture appears on the screen.• Turn on the video component if it is not on.
• Playback picture is not clear and legible.
Disconnect the adapter from both this unit and iPod.
Then, connect them again.
unit.
Reset the iPod.
Current disc does not include playable files. Replace the
disc with one including playable files.
Перед тем, как приступать к эксплуатации, пожалуйста, внимательно прочитайте все инструкции с тем,
чтобы полностью изучить и обеспечить оптимальную работу этого устройства.
Благодарим Вас за приобретение изделия JVC.
ВАЖНО ДЛЯ ЛАЗЕРНОЙ АППАРАТУРЫ
1. ЛАЗЕРНАЯ АППАРАТУРА
КЛАССА 1
ПРЕДУПРЕЖДЕНИЕ:
2.
открывайте верхнюю крышку.
Внутри устройства нет частей,
которые пользователь может
отремонтировать. Ремонт должен осуществляться квалифицированным обслуживающим персоналом.
3. ПРЕДУПРЕЖДЕНИЕ: В открытом состоянии происходит видимое и/или невидимое излучение лазера класса
1M. Не смотрите непосредственно в оптические инструменты.
РУCCKИЙ
4. ЭТИКЕТКА: ПРЕДУПРЕЖДАЮЩАЯ ЭТИКЕТКА, РАЗМЕЩЕННАЯ НА НАРУЖНОЙ СТОРОНЕ УСТРОЙСТВА.
ПРЕДУПРЕЖДЕНИЯ:
(Предотвращение несчастных случаев и
повреждений)
• НЕ устанавливайте устройства и не
прокладывайте провода в местах, где;
– оно может помешать рулевому управлению
и переключению передач.
–
оно может помешать функционированию средств
безопасности, например, пневмоподушкам.
– может ухудшиться обзор.
• НЕ управляйте устройством во время вождения
автомобиля.
При необходимости управления устройством
во время вождения автомобиля внимательно
следите за дорогой.
• Водителю не следует смотреть на монитор во
время вождения.
• Водителю не следует надевать наушники во
время вождения.
•
Чрезмерное звуковое давление из вставных или
накладных наушников может вызвать потерю слуга при
прослушивании звука через вставные или накладные
наушники с использованием режима “Dual Zone”.
Не
Предостережения (монитор):
•
Встроенный в устройство монитор изготовлен
с высокой точностью, однако он может иметь
нерабочие точки. Это явление неизбежно и не является
результатом неисправной работы оборудования.
• Не подвергайте монитор воздействию прямых
солнечных лучей.
•
Не используйте шариковую ручку и подобные предметы с
острым наконечником для работы с сенсорной панелью.
Касайтесь кнопок сенсорной панели непосредственно
пальцами (если на Вас перчатки, необходимо их снять).
• При слишком низкой или слишком высокой
температуре может произойти следующее:
– Внутри происходит химическая реакция,
приводящая к неисправности устройства.
–
Изображения могут отображаться нечетко
или воспроизводиться замедленно. Может
нарушаться синхронность изображения и
звука или ухудшаться качество изображения.
•
При длительном отображении некоторых изображений
на мониторе может оставаться остаточное изображение.
Это не является неисправностью. Выключите устройство
или отобразите другое изображение.
[только Европейсий Союз]
В соответствии с Законом Российской Федерации “О защите прав потре бителей” срок службы (годности) данного
товара “по истечении которого он может представлять опасность для жизни, здоровья потребителя, причинять вред
его имуществу или окружающей среде” составляет семь (7) лет со дня производства. Этот срок является временем,
в течение которого потребитель данного товара может безопасно им пользоваться при условии соблюдения
ин струк ции по эксплуатации данного товара, проводя необходимое обслуживание, включающее замену расходных
материалов и/или соответствующее ремонтное обеспечение в специализированном сервисном центре.
Дополнительные косметические материалы к данному товару, поставляе мые вместе с ним, могут
храниться в течение двух (2) лет со дня его производства.
Срок службы (годности), кроме срока хранения дополнительных космети ческих материалов, упомянутых в
предыдущих двух пунктах, не затрагивает никаких других прав потребителя, в частности, гарантийного свидетельства
JVC, которое он может получить в соответствии с законом о правах потребителя или других законов, связанных с ним.
2
Как пользоваться данным руководством:
• < > обозначает изменяемые экраны/меню/
операции/настройки, которые появляются на
сенсорной панели.
• [ ] обозначает кнопки на сенсорной панели.
• ( номер страницы) обозначает номер
страницы для справки по связанным темам/
операциям/настройкам.
• Указатель операций: Удобный и быстрый
поиск желаемых операций/функций. (
•Язык отображения: Элементы индикации
на английском языке используются в
качестве примера с целью объяснения.
Можно выбрать язык индикации в меню
<Language>. (
• Иллюстрации: Для объяснения используются
главным образом иллюстрации KD-AVX77.
15)
73)
Как перенастроить Ваше
устройство
• Запрограммированные настройки будут также
удалены (за исключением зарегистрированных
устройств для KD-AVX77,
Принудительное извлечение диска, 36.
Для Вашей безопасности...
• Не повышайте слишком сильно уровень
громкости, поскольку это заглушает внешние
звуки, делая опасным управление автомобилем,
а также может привести к потере слуха.
• Остановите автомобиль перед тем, как выполнять
любые сложные операции.
Температура внутри автомобиля...
Если Вы припарковали Ваш автомобиль на
длительное время в жаркую или холодную погоду,
перед тем, как включать это устройство, подождите
до тех пор, пока температура в автомобиле не
придет в норму.
32)
CОДЕРЖАНИЕ
Как пользоваться данным руководством
Как перенастроить Ваше устройство ........ 3
ВВЕДЕНИЕ
Тип воспроизводимых дисков .................. 4
Основные операции ................................... 5
*1 Если установить видео DVD-диск с неправильным кодом региона, на экране отображается сообщение
“Region code error”.
*2 Диски DVD-R, записанные в формате “multi-border”, тоже воспроизводятся (кроме двухслойных дисков).
Двухслойные диски DVD-RW не воспроизводятся.
*3 Возможно воспроизведение завершенных дисков +R/+RW (только в видеоформате). “DVD” выбирается в
качестве типа диска когда загружается диск +R/+RW. Двухслойные диски +RW не воспроизводятся.
*4 Данное устройство не может воспроизводить содержимое, защищенное с помощью CPRM (Content
Protection for Recordable Media—защита содержимого для перезаписываемых носителей).
*5 Данное устройство может воспроизводить файлы AAC, кодированные с помощью iTunes.
Предостережение для воспроизведения дисков DualDisc
Сторона диска DualDisc, отличная от DVD, не совместима со стандартом “Compact Disc Digital Audio”. Поэтому
не рекомендуется использовать сторону диска DualDisc, отличную от DVD, на данном устройстве.
4
Основные операции
SRC
KEY
QUICK
MENU
Использование панели монитора/сенсорной панели
Сенсорная панель (см. следующие страницы).
Объяснение большинства операций приводится с
использованием сенсорной панели, если не указано
обратного.
Панель монитора
SRC
Кабель USB, идущий от задней панели устройства, (
1 Отображение экрана меню AV. ( 12)
2 Отображение меню источника.*
3 Индикатор Bluetooth (только для KD-AVX77)
4 • Включение питания.
1
( 7)
• Ослабление звука (при включенном питании).
• Выключение питания. (Удерживать)
• Переключение устройства связи во время
разговора по сотовому телефону Bluetooth.
(только для KD-AVX77, 49)
• Настройка уровня громкости входящих
звонков. *2 (только для KD-AVX77)
9 • Отображение экрана Open/Tilt. ( 6)
• Извлечение диска и отображение экрана
Open/Tilt. (Удерживать)
MP3
CD
01 02 0:01:20
Track Title
Artist Name
Disc Title
FLAT
15:45
p Отображение быстрого меню. ( 7)
q Изменение кнопок, отображаемых на
сенсорной панели. ( 6)
*1 Доступные источники зависят от
подключенных внешних устройств,
используемых носителей и настроек,
выполненных на экране < > (вход).
( 19)
*2 Эта настройка не влияет на уровень громкости
других устройств.
Подсоединение панели монитора
РУCCKИЙ
47, 51)
5ВВЕДЕНИЕ
Когда изображение воспроизводится на экране,
индикация кнопок и информации на сенсорной
панели отключается приблизительно через 10
секунд после выполнения последней операции.
• Способ отключения индикации кнопок и
информации можно выбрать в <Monitor/Sensor>. (
Индикация кнопок и информации включается снова:
– При поднесении руки к
сенсорной панели (в
зависимости от настройки
РУCCKИЙ
<Monitor/Sensor>,
20).
– При нажатии кнопки на панели монитора.
– Для KD-AVX77: При поступлении входящего
вызова или SMS на сотовый телефон Bluetooth.
•
Индикация кнопок и информации может включаться
и в других случаях, отличных от вышеописанных.
20)
Предостережение, касающееся
настройки громкости:
По сравнению с другими источниками
воспроизведения цифровые устройства (CD/USB)
создают незначительный шум. Уменьшите громкость
перед воспроизведением, чтобы предотвратить
повреждение динамиков из-за внезапного
повышения уровня громкости на выходе.
Можно также настраивать громкость, перемещая
палец по любой части сенсорной панели, как это
показано на рисунке.
Кнопки на сенсорной панели
При каждом прикосновении к [KEY] отображаемые
на сенсорной панели кнопки изменяются.
Пример: Когда в качестве источника звука выбран
“
TUNER
”
Кнопки операций
Кнопки источника
• Доступные кнопки меняются в зависимости от
источников.
• Фоновый рисунок можно изменить с помощью
настройки <Wall Paper>. (
13)
Экран Open/Tilt
Перетаскивание пальца по сенсорной панели
работает так же, как касание [5 / ∞ / 4 /
¢].
• При перемещении или перетаскивании
пальца плотно касайтесь панели.
Быстрое меню позволяет с легкостью получать
доступ к некоторым часто используемым
функциям.
Отображение меню <PTy Search>.
( 34)
Включение или выключение
функции резервного приема
сообщений. ( 25)
Включение или выключение
функции резервного приема TA.
( 18)
Изменение настройки <IF Band Width>. ( 18)
Изменение управления устройством
iPod/iPhone для “iPod USB”. ( 16)
Только для KD-AVX77
Позволяет захватить текущее
воспроизводимое изображение.
( 13)
Отображение меню набора <Dial Menu>. ( 29)
РУCCKИЙ
• Доступные значки меняются в зависимости от
источников.
Отображение меню <Monitor/Sensor>. ( 20)
Изменение режима звучания. ( 23)
Включение или выключение функции
объемного звучания. ( 21)
Включение или выключение повтора
дорожек или разделов. ( 26)
Изменение настройки <Aspect>.
( 15)
Активация или деактивация функции
резервного приема PTY. ( 25)
7ВВЕДЕНИЕ
Использование пульта дистанционного управления (RM-RK252)
Установка батарей
R03/LR03/AAA
РУCCKИЙ
Вставьте аккумуляторные батареи в пульт
дистанционного управления, соблюдая полярность
(+ и –).
Внимание:
• Неправильная замена батареи приводит к
опасности взрыва. Заменяйте на батареи только
того же или эквивалентного типа.
• Не подвергайте аккумуляторные батареи
действию повышенных температур: не
подвергайте их длительному воздействию
солнечных лучей, не бросайте в огонь и т.п.
При уменьшении радиуса действия или
эффективности пульта дистанционного
управления замените батареи.
Перед использованием пульта
дистанционного управления выполните
следующие действия:
• Направьте пульт дистанционного управления
непосредственно на телеметрический датчик
приемника.
• НЕ подвергайте телеметрический датчик
воздействию яркого света (прямых солнечных
лучей или искусственного освещения).
Приемник поставляется с функцией рулевого
пульта дистанционного управления.
• Для получения информации о подключении
монитора см. Руководство по установке/
подключению (в отдельном издании).
• Операции могут отличаться в зависимости
от типа рулевого пульта дистанционного
управления.
8
1 Кнопка *
1
• Включение питания.
•
Приглушение звука при включенном питании.
• Выключение питания. (Удерживать)
2 Кнопки5/∞
•
TUNER
: Выбор запрограммированных
радиостанций.
•
DAB
: Выбор служб.
•
DISC/USB/CD-CH
:
– Видео DVD-диск: Выбор названия.
– DVD-VR: Выбор программы/списка
воспроизведения.
– DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC:
Выбор папок, если содержатся.
•
iPod USB
следующего элемента.*
•
iPod
(когда подключен к KS-PD100):
: Выбор предыдущего или
2
–5 : Вход в главное меню (затем кнопки
5 / ∞ / / служат для
перемещения по меню).
5 : Возврат к предыдущему меню.
∞ : Подтверждение выбора.
• Настройка громкости сигнала, получаемого
через разъем 2nd AUDIO OUT при нажатии
кнопки SHIFT.
4 Кнопка ASPECT*
4
• Изменение формата воспроизводимых
изображений.
5 Кнопка PHONE*
1 *3
• Отображение открывавшегося последним
меню в <Dial Menu>.
• Отображение меню <Redial>. (Удерживать)
• Ответ на входящие вызовы.
6 Кнопка SETUP*
•
Выполняет только функцию цифровой кнопки.
7 Кнопка TOP M (меню)*
4
4
• Видео DVD-диск: Отображение меню дисков.
• DVD-VR: Отображение экрана “Original
Program”.
• VCD: Возобновление воспроизведения PBC.
8 Кнопка OSD (индикация на экране)
• Отображение строки состояния.
• Не выполняет функцию “ ”.
*1 Если включена функция “Dual Zone”, эти кнопки
использовать нельзя.
*2 Может не работать в зависимости от того,
как была выбрана текущая дорожка или
видеозапись.
*3 Только для KD-AVX77
*4 В сочетании с кнопкой SHIFT выполняет функцию
нумерованных кнопок.
–
DISC/USB
: Ввод номера раздела/названия/
программы/списка воспроизведения/папки/
дорожки после входа в режим поиска путем
нажатия SHIFT и DIRECT. ( 40)
–
TUNER/DAB
: (Цифры от 1 до 6): Ввод
запрограммированной радиостанции или
службы.
Продолжение не следующей странице
9ВВЕДЕНИЕ
РУCCKИЙ
9 Кнопка SHIFT
• Функции с другими кнопками.
p Кнопка DISP (дисплей)*
1
• Закрытие экрана меню, если меню было
открыто.
•
DISC/USB/iPod USB
: Отображение кнопок
и информации на сенсорной панели, когда
отображается изображение/картинка Jacket
Picture/обложка.
DAB
•
РУCCKИЙ
q Кнопки 1 / ¡
•
: Отображение DLS (Dynamic Label
Segment—динамический сегмент метки).
DISC/USB
:
– Поиск назад/поиск вперед. (недоступно
для JPEG)
– Видео DVD-диск: Медленное
воспроизведение (во время паузы).
– DVD-VR/VCD: Прямое замедленное
воспроизведение (во время паузы).
iPod USB
•
w Кнопка SOURCE*
: Поиск назад/поиск вперед.
1
• Осуществляет выбор источника звука.
e Кнопка3 (воспроизведение) / 8 (пауза)
•
DISC/USB/iPod USB
воспроизведения или пауза.
• Ответ на входящие вызовы.*
•
Bluetooth
r Кнопка (завершение звонка)*
: Начало воспроизведения.*
: Начало
3
3
• Завершение вызова.
Кнопка BAND
•
TUNER/DAB
: Выбор диапазонов частот.
Кнопка7 (останов)
•
DISC/USB
•
Bluetooth
t Кнопка RETURN*
: Останов воспроизведения.
: Пауза воспроизведения.*
4
• VCD: Возврат к меню PBC.
• Видео DVD-диск/DVD-VR/DivX/MPEG1/MPEG2/
JPEG/VCD: Отмена всплывающего меню на
строке состояния на экране.
yКнопка MENU*
4
• Видео DVD-диск: Отображение меню дисков.
• DVD-VR: Отображение экрана “Play List”.
• VCD: Возобновление воспроизведения PBC.
u Кнопки % / fi*
4
• Видео DVD-диск: Выбор или выполнение
настроек.
CD-CH
•
: Изменение дисков в загрузочном
устройстве.
Кнопки@ / #*
4
• Видео DVD-диск: Выбор или выполнение
настроек.
• DivX/MPEG1/MPEG2: Переход назад или
вперед приблизительно на 5 минут.
Кнопка ENT (ввод)*
4
• Подтверждение выбора.
i Кнопка DUAL
• Включение или отключение функции “Dual
Zone”.
• Не выполняет функцию “#”.
o Кнопка DIRECT
•
DISC/USB
: Переключение в режим прямого
поиска раздела/названия/программы/списка
воспроизведения/папки/дорожки при
нажатии с кнопкой SHIFT. ( 40)
3
Кнопка CLR (очистка)
•
DISC/USB
: Удаление ошибочного ввода при
нажатии с кнопкой SHIFT.
Кнопка SURROUND*
•
DISC/USB
1
: Изменение режима объемного
звука.
*1, *3, *4 9
3
10
Подготовка
Отмена демонстрации функций дисплея и установка часов
~ Включение питания.
Ÿ Отображение меню AV.
! Выберите <AV Setup>.
⁄ Отмена демонстрации.
Коснитесь <Interval>, чтобы отобразить
элементы настройки.
Выберите <Off>, затем коснитесь <>.
@ Настройка часов.
Выберите < > (часы).
РУCCKИЙ
Изменить элемент для настройки (1),
затем настройте минуты (2).
¤ Завершите процедуру.
Настройте час.
11ВВЕДЕНИЕ
Общее представление о меню AV
Меню AV можно использовать для выполнения большинства операций и настроек. Доступные элементы
меню отображаются на сенсорной панели в зависимости от выбранного источника.
Следующие действия являются одной из основных процедур.
• Выполнение операций/задание настроек можно осуществлять, следуя этим указанным действиям, если не
упоминается иное.
~ Включение питания.
РУCCKИЙ
Ÿ Отображение меню AV.
• AV Setup:
• Disc Surround:
• Equalizer:
• Sound:
• Mode:
• List:
• Dual Zone:
Только для KD-AVX77
•Bluetooth:
13 – 20
21, 22
23
24
25, 26
27, 28
43 – 46
29 – 32
! Коснитесь желаемой иконки/
элемента, чтобы выполнить
желаемую операцию/настройку.
• Для некоторых настроек вложенные
окна не отображаются, а выбор
параметра уже приводит к изменению
настройки.
• Недоступные элементы затемняются.
Переход к предыдущей/
следующей странице меню
Возврат к предыдущему экрану.
Переход к следующей категории в
<AV Setup>:
Указание на наличие
следующего иерархического
уровня/элемента настройки.
Закрытие экрана
меню AV.
12
AV Setup (A/B Установки)
По умолчанию: Подчеркнуто
Элемент менюНастройки/элементы, доступные для выбора
Demonstration
(Демонстрация)
Wall Paper
(Фоновый Рисунок)
Capture (Захват)
(Только для
KD-AVX77)
Дисплей
♦
Off
♦
On
: Отмена.
: Включение демонстрации на экране. Для временной
остановки коснитесь экрана.
♦
Interval
: Включение демонстрации с 20-секундными
интервалами.
Можно выбрать фоновый рисунок экрана.
Для KD-AVX77:
♦
Ring, Plain, Road, Night, User Capture 1, User Capture 2, User Capture 3,
User Capture 4
Для KD-AVX55:
♦
Ring, Plain
Можно захватить изображение, отображаемое на экране, и использовать его
в качестве фонового рисунка.
♦
Normal
♦
Zoom
: Захват изображения без увеличения.
: Захват изображения с увеличением до ширины
экрана.
Во время воспроизведения или паузы воспроизведения изображения...
1 Выберите <Normal> или <Zoom>.
• Когда выбрано <Zoom>, последовательно постукивайте по экрану,
пока не отобразится желаемая часть.
2 Захватите изображение.
РУCCKИЙ
[ ]: Захват изображения.
[ ]: Отмена.
3 Выберите одну из цифр (<1> – <4>), чтобы сохранить изображение для
• Символы, которые можно вводить для названий, могут также различаться
в зависимости от выбранного языка. ( 63)
Выбор положения кнопок на сенсорной панели.
♦
Left, Right
♦
Off
♦
On
По умолчанию 0:00 (
: Отмена.
:
Включение режима двух экранов “Dual Display”. ( 43, 46, 56)
11)
Выбор 12-часового или 24-часового формата.
♦
12 Hours, 24 Hours
♦
Off
♦
On
: Отмена.
: Время часов отображается на воспроизводимом изображении.
Выберите <Auto> для автоматической подстройки часов с использованием
данных о времени (CT), поступающих от радиостанции FM Radio Data System.
♦
Off, Auto
РУCCKИЙ
15AV MENU
Menu Language
(Меню Языков) *
Audio Language
(Авт. Выбор Языка) *
Subtitle (Субтитры) *
Monitor Type
РУCCKИЙ
(Тип Монитора) *
Элемент менюНастройки/элементы, доступные для выбора
6, *7
6, *7
Выбор первоначального языка меню диска; По умолчанию Руccĸий
( 64)
Выбор первоначального языка аудио; По умолчанию Руccĸий ( 64)
6, *7
6, *7
Выбор первоначального языка субтитров или отключение субтитров
<Off>; По умолчанию Руccĸий ( 64)
Выбор типа монитора для просмотра широкоэкранного изображения
на внешнем мониторе.
♦
16:9
: Выберите этот параметр, если формат экрана
внешнего монитора - 16:9.
♦
4:3 Letterbox,
4:3 Pan Scan
: Выберите этот параметр, если формат экрана
внешнего монитора - 4:3.
OSD Position
(Позиция OSD) *
File Type (Тип Файла)
6, *7
6, *7
*
Диск
DivX Regist. (Registration)
(DivX Регистрация) *
Artwork (Обложка)Для “
iPod Control
(управление iPod) *
6
9
Выберите положение экранной строки. ( 42)
• При некоторых настройках <Aspect> экранная строка полностью не
отображается. ( 15)
♦
1
♦
2
: Самое высокое положение.
: Самое низкое положение.
Выберите тип файла для воспроизведения, если диск или устройство
USB содержит файлы различных типов. Эту настройку можно
сохранять отдельно для каждого источника—“
У данного устройства имеется собственный регистрационный код.
В целях охраны авторского права при воспроизведении файла с
записанным регистрационным кодом выполняется перезапись
регистрационного кода устройства.
DISC/USB
”: На экране отображается надпись “Jacket picture”.*
( 37)
Для “
iPod USB
”: Обложка (Artwork) отображается на экране в режиме
Элемент менюНастройки/элементы, доступные для выбора
D. (Dynamic)
Range Compres.
(Compression)
(Сжат. Д/
Диапаз.) *
Speaker Size
(Размер
Динамика) *
Диск
Speaker Level
(Уровень
Динамика) *
7
При воспроизведении программы Dolby Digital с диска можно наслаждаться
мощным звуком даже на небольшой громкости.
♦
Auto
: Выберите, чтобы применить действия к программному
обеспечению многоканального кодирования.
♦
On
: Выберите для постоянного использования этой функции.
Настройка размера динамиков.
6, *7
♦
Передние динамики: Small, Large
♦
Центральный динамик: None, Small, Large
♦
Задние динамики: None, Small, Large
♦
Низкочастотный динамик: On, Off
• Размер динамика: <Large> для диаметра не менее 13 см; <Small> для
диаметра не более 13 см.
• Передние динамики и задние динамики: левые и правые динамики не
могут регулироваться отдельно.
Независимо от приведенной выше настройки...
• Звук в низкочастотном динамике во время воспроизведения в режимах
“Dolby Pro Logic II Movie” или “Music” отсутствует, если для типа переднего
динамика установлено значение <Large>.
• Если функция объемного звучания отключена, центральный динамик не
используется. ( 21)
Можно настроить уровень выходного сигнала активированных динамиков
(выше), прослушивая пробный звук.
6
1 Передние
2 Центральный
3 Задние
4
динамики
динамик
динамики
Низкочастотный
динамик
РУCCKИЙ
Настраивает выходной уровень каждого динамика в диапазоне от –10 dB до
+10 dB; По умолчанию 00dB
• Коснитесь [TEST], чтобы включить пробный звук. Чтобы остановить,
коснитесь [CANCEL].
• Настройка уровня низкочастотного динамика действует, только когда
включена функция объемного звучания. ( 21)
6
Доступно только для “
*
DISC/USB
”.
*7 При изменении настройки воспроизведение останавливается.
*8 Для отображения обложки требуется не менее 5 секунд, и во время загрузки все операции недоступны.
*9 Доступно только для “
iPod USB
”.
Продолжение не следующей странице
17AV MENU
Элемент менюНастройки/элементы, доступные для выбора
Speaker Distance
(Расстояние До д.)
Можно настроить время вывода выходного сигнала активных динамиков
6
*
(выше).
Диск
РУCCKИЙ
IF Band Width
(Ширина Полосы ПЧ)
AF Regional
(Рег. Альт. Част.) *
Тюнер
TA Standby
(Выключение TA)
TA Volume
(Громкость ТА)
6
17
*
*10 Не доступно, когда в качестве диапазона выбрано AM/FM3.
*11 Зависит от использования регулятора усиления. ( 24)
Настройка расстояния от динамика до места для прослушивания в
диапазоне от 15 cm/6 inch до 600 cm/240 inch с шагом 15 cm/6 inch; по
умолчанию 120 cm/48 inch (для центрального динамика), 150 cm/60 inch
(для передних и задних динамиков).
• Коснитесь [cm/inch] для изменения единиц измерения—см и дюймы.
♦
Auto
: Повышение избирательности тюнера для устранения
интерференционных помех от соседних радиостанций.
(Сопровождается потерей стереоэффекта.)
♦
Wide
: Могут возникать взаимные помехи от соседних
радиостанций, но качество звучания при этом не
ухудшается и сохраняется стереоэффект.
Настройку сеть-отслеживающего приема можно изменить. ( 35)
10
Когда принимаемые от текущей радиостанции сигналы становятся
слабыми...
♦
Off
: Отмена—нельзя выбрать, если для <DAB AF>
установлено значение <On>.
♦
AF Regional
: Переключение на другую радиостанцию, передающую
ту же программу. Загорается индикатор REG.
♦
AF
: Переключение на другую радиостанцию. Программа
может отличаться от принимаемой в текущий момент
программы (Загорается индикатор AF). ( 35)
♦
Off
10
♦
*
On
: Отмена.
: Включение функции резервного приема TA. ( 35)
Можно настроить предустановленный уровень громкости сообщений о
движении на дорогах (ТА).
Когда устройство переключается на прием сообщений о движении
на дорогах (TA), уровень громкости автоматически меняется на
запрограммированный уровень TA, если текущий уровень громкости ниже
запрограммированного. (
♦
00 от до 30 или 50*11, По умолчанию 15
35)
18
Элемент менюНастройки/элементы, доступные для выбора
Program Search
(Поиск Программы)
DAB AF
Тюнер
(Альтерн.
Частоты) *
12
AV Input (Аудио/
Видео Вход) *
Можно включать и выключать поиск программы. (
♦
Off
♦
On
: Отмена.
: Активация поиска программы.
Можно включать и выключать поиск альтернативной частоты. ( 55)
♦
Off
♦
On
Выбор назначения для разъемов LINE IN и VIDEO IN. ( 56)
аудио- и видеоустройств, например,
видеомагнитофона.
♦
Вход
External Input
(Внешний Вход) *
Audio
♦
Camera *
♦
Navigation
Для подключения внешнего устройства к гнездовому разъему на задней
16
панели устройства автоматической смены компакт-дисков.
: Выберите при подключении аудиоустройства,
14, *15
например переносного звукового проигрывателя.
: Выберите при подключении камеры заднего вида.
: Выберите при подключении системы навигации.
• Для подключения тюнера DAB данная настройка не требуется. Тюнер DAB
обнаруживается автоматически.
♦
Changer/iPod *
17
: Устройство автоматической смены компакт-дисков,
( 53), iPod, ( 52).
♦
External
:
Любые устройства, кроме указанных выше, ( 57).
*12 Выбор возможен только при подключении тюнера DAB. ( 54)
*13 Недоступно, если в качестве источника выбрано “
AV-IN
”.
*14 Необходимо подключение провода REVERSE GEAR SIGNAL. См. Pуководство по установке/подключению.
При переключении рычага коробки передач в положение заднего хода (R) передаваемое через камеру
изображение заднего вида отображается на экране в формате <16:9 FULL> (независимо от настройки
формата). При переключении рычага коробки передач в положение, отличное от положения заднего хода
(R), экран заднего вида исчезает.
*15 Пока на мониторе отображаются изображения с камеры, сообщения не отображаются.
*16 Недоступно, когда в качестве источника выбрано внешнее устройство, подключенное к гнездовому
разъему устройства автоматической смены компакт-дисков.
*17 Отображается название компонента, обнаруженного через разъем устройства автоматической смены
компакт-дисков.
35)
” не отображается в меню
51)
РУCCKИЙ
19AV MENU
Элемент менюНастройки/элементы, доступные для выбора
Beep (Звук Сигнала)♦ Off
Telephone Muting
(Откл. Звука Тел.) *
Monitor/Sensor
(Монитор/Сенсор)
РУCCKИЙ
Другие
♦
On
♦
Off
18
♦
Muting1,
Muting2
Можно отключать индикацию кнопок и информации, отображаемых на
сенсорной панели, или отключать сенсорную панель, когда в течение 10
секунд не выполняется никаких операций. (
Normal/
Motion
Normal/Touch Кнопки и информация
WallPaper/
Motion
WallPaper/
Touch
Off/MotionСенсорная панель загорается при поднесении к ней руки.
Off/TouchСенсорная панель загорается при прикосновении к ней.
: Отмена.
: Включение звука нажатия кнопки.
: Отмена.
: Выберите любой из параметров, обеспечивающий
отключение звука при использовании сотового
телефона.
Во время воспроизведения
изображения на экране
Кнопки и информация
загораются при поднесении руки
к сенсорной панели.
загораются при прикосновении к
сенсорной панели.
Кнопки и информация загораются при поднесении руки к
сенсорной панели.
Кнопки и информация загораются при прикосновении к
сенсорной панели.
6)
Прочее
Кнопки и информация
постоянно горят.
Motion Sensitiv.
(Sensitivity) (Чувствит.
Изменение чувствительности датчика для <Monitor/Sensor> (вверху).
♦
Mid, High
Движе.)
Initialize (Начальн
Настрой.)
18
Требуется подсоединение к системе сотового телефона. См. Pуководство по установке/подключению.
*
Инициализация всех настроек, выполненных в меню AV. Удерживайте
[Enter] для инициализации настроек, затем перезапустите устройство.
3)
(
20
Disc Surround (Диск с Окр. Зв.)
Вы можете прослушивать многоканальный объемный звук через передние, центральный и окружающие
динамики.
MULTI:
Для таких источников с многоканальным кодированием, как Dolby Digital. (Если эта функция активна, на
экране отображается надпись “MULTI”.)
Dolby Pro Logic II (Movie/Music):
Для двухканальных источников, кроме дисков DivX/MPEG1/MPEG2.
• После подключения центрального динамика не забудьте его включить, иначе звук от центрального
динамика будет отсутствовать. (
• Эту функцию невозможно включить в следующих случаях:
– Если в качестве источника звука выбран “
– Когда используется функция “Dual Zone”.
17)
iPod USB
”.
Включение функции объемного звучания
1
Выберите <Disc Surround> в меню AV.
2 Включите функцию объемного
звучания.
Включите функцию объемного звучания (1),
затем коснитесь <Auto>, чтобы отобразить
режимы объемного звучания (2).
3
Выберите режим объемного звучания.
<Auto>:
• Функция объемного звука “MULTI”
активируется при обнаружении
многоканальных цифровых сигналов.
• При поступлении на вход 2-канальных
или 2,1-канальных сигналов*
включается функция 4-канального
стереофонического звучания.
<Through>:
Все входящие сигналы каналов передаются
на соответствующие динамики.
<Dolby PLII Movie>:
Включите режим Dolby Pro Logic II Movie.
<Dolby PLII Music>:
Включите режим Dolby Pro Logic II Music.
Можно изменить значения настроек
<Panorama> и <Center Width>. ( 22)
* Кроме сигналов дисков DivX, MPEG1 или MPEG2.
РУCCKИЙ
Продолжение не следующей странице
21AV MENU
На пульте дистанционного управления:
Изменение настройки <Dolby PLII Music>
В действии 3 на стр. 21...
1 Выберите <Dolby PLII Music>.
РУCCKИЙ
2 Выберите требуемую настройку.
<Panorama>:
Выберите <On> для добавления эффекта
“звук вокруг”.
<Center Width>*:
Настройка центрального звука таким
образом, чтобы он был слышен только
из центрального динамика, только из
левого/правого передних динамиков
как “призрачный” центральный звук или
использовались различные комбинации
этих динамиков. Чем больше числовое
значение, тем выше уровень “призрачного”
эффекта (обычно устанавливается <04>).
* Можно настроить, когда включен
центральный динамик. ( 17)
3 Завершите процедуру.
• Настройки <Dolby PL II Music> нельзя
изменить с помощью пульта дистанционного
управления.
22
Equalizer (Эквалайзер)
Можно выбрать предустановленный режим звучания, соответствующий музыкальному жанру.
♦
Flat (По умолчанию), Hard Rock, R&B, Pop, Jazz, Dance, Country, Reggae, Classic, User1, User2, User3
• (Для “
DISC/USB
следующем случае: в качестве источника выбрано CD-DA, VCD или файлы MP3/WMA/WAV/AAC и для
<Surround Mode> выбрано значение <Auto>. (
”) Пока включена функция объемного звучания, эквалайзер можно использовать в
station Sequential
Memory—
последовательная
память для
радиостанций
с устойчивым
сигналом) (SSM)
PTy Standby
(Фикс. Типа
1
Прог.) *
PTy Code
(Код Типа Прог.) *
D.(Dynamic) Range
Control
(Упр. Д/Диапазон.)
Announce Standby
(Извещение
Выкл.)
Announce Code
(Код Извещения)
1
*
Не доступно, когда в качестве диапазона выбрано FM3.
*2 Только для KD-AVX77
монофонический режим для обеспечения лучшего качества приема.
♦
Off
♦
On
: Возобновление стереоэффекта.
:
Включение монофонического режима для улучшения качества приема
FM, но стереоэффект будет потерян. Загорается индикатор MONO.
Для каждого диапазона FM можно предварительно запрограммировать до 6 радиостанций.
• Осуществляется поиск местных FM-радиостанций с наиболее сильными сигналами
и их автоматическое сохранение в диапазоне FM.
(Удерживать)
Можно включать и выключать функцию резервного приема PTY. ( 35)
♦
Off
♦
On
Выбор кода PTY для функции резервного приема PTY. ( 34, 35)
1
: Отмена.
: Включение функции резервного приема PTY.
Некоторые службы DAB передают сигналы динамического контроля диапазона
(Dynamic Range Control—DRC) вместе с сигналами обычных программ. Система DRC
усилит сигналы низкого уровня, чтобы улучшить качество звучания.
♦
Off: Отмена.
♦
DRC1, DRC2, DRC3
: Чем больше числовое значение, тем сильнее эффект.
Можно включать и выключать функцию резервного приема сообщений. (
♦
Off
♦
On
Выбор типа сообщений для резервного приема. (
♦
Transport News, Warning, News, Weather, Event, Special Event, Radio Info,
: Отмена.
: Включение функции резервного приема.
55)
Sports News, Financial News
РУCCKИЙ
55)
Продолжение не следующей странице
25AV MENU
Элемент менюНастройки/элементы, доступные для выбора
Repeat (Повтор)
РУCCKИЙ
Random
(Произвольный)
AudioBooks
(Звуковые
Книги) *
Title Entry
(Заголовок)
5
Доступные элементы зависят от типов загруженного диска и воспроизводимого файла.
♦
Chapter
♦
Title
♦
Program
: Повтор текущего раздела.
: Повтор текущего названия.
: Повтор текущей программы (Для DVD-VR, недоступно при
воспроизведении списка воспроизведения).
♦
Disc
♦
Folder/Group*
♦
Track
: Повтор всех дорожек текущего диска.
3
: Повтор всех дорожек текущей папки или группы
: Повтор текущей дорожки. (Для VCD-диска: Когда не
используется функция PBC.)
♦
One
♦
All
♦
Off
Доступные элементы зависят от типов загруженного диска и воспроизводимого файла.
♦
Folder/Group*
: Функция, аналогичная функции “Repeat One” в iPod/iPhone.
: Функция, аналогичная функции “Repeat All” в iPod/iPhone.
: Отмена.
3
: Произвольное воспроизведение всех дорожек в текущей
папке/группе, а затем дорожек в других папках/группах.
♦
Disc/USB
: Произвольное воспроизведение всех дорожек. (Для
VCD-диска: Когда не используется функция PBC.)
♦
All
: Воспроизведение всех дорожек всех загруженных дисков в
случайном порядке.
♦
Song
♦
Album
♦
Off
:
Функция, аналогичная функции “Shuffle Songs” *4 в iPod/iPhone.
: Функция, аналогичная функции “Shuffle Albums” в iPod/iPhone.
: Отмена.
Можно выбрать скорость воспроизведения звукового файла из категории
“Audiobook” в iPod/iPhone.
♦
Normal
♦
Faster
♦
Slower
Источникам “
: Воспроизведение на обычной скорости.
: Более быстрое воспроизведение.
: Более медленное воспроизведение.
AV-IN
” и “
EXT-IN
” можно присвоить названия (до 16 знаков).
(Сведения о доступных символах, 63.)
[5/∞]: Изменение символов по одному.
[2/3]: Перемещение курсора.
[SPACE]: Ввод пробела.
[CHANGE]: Смена набора символов.
[STORE]: Подтверждение ввода.
[CLEAR]: Удаление всех введенных символов.
*3 Только для KD-AVX77
*4 Можно включить функцию <Shuffle Songs> в меню <Search Mode>. ( 28)
*5 Недоступно для выбора при подключении iPod с помощью интерфейсного адаптера. ( 52)
1 Коснитесь [BAND], затем [ / ], чтобы выполнить настройку на
радиостанцию/службу, которую необходимо запрограммировать.
2 Коснитесь [ ], а затем [List].
3 Выберите запрограммированный номер.
Пример: Во время сохранения радиостанции FM
(Удерживать)
Коснитесь, чтобы выбрать диапазон частот.
Радиостанция, выбранная в действии 1, сохранена под номером 4.
• Выбор запрограммированной радиостанции или службы из списка
Пример: При выборе запрограммированной радиостанции FM
DISC/USBВыбор дорожки из списка
Если на диске или устройстве имеются папки, можно вывести на экран списки папок
или дорожек (файлов), а затем начать воспроизведение.
РУCCKИЙ
Касайтесь/перетаскивайте, чтобы просмотреть списки.
Продолжение не следующей странице
1 Номер текущей папки
в списке/общее число
папок в списке
2 Номер текущей
дорожки в списке/
общее число дорожек
в текущей папке
27AV MENU
Источник звукаРабота/настройка
iPod USBВыбор дорожки или видеозаписи с экрана <Search Mode>*
♦
Music
♦
РУCCKИЙ
Videos
♦
Shuffle Songs
Прикасайтесь/перетаскивайте, чтобы просмотреть список.
CD-CHВыбор диска из списка
: Playlists, Artists, Albums, Songs, Podcasts, Genres,
Composers, Audiobooks
:
Video Playlists, Movies, Music Videos, TV Shows, Video Podcasts
: Начало воспроизведения.
1
1 Номер текущей
дорожки в списке/
общее число дорожек
в текущей папке
• При выборе текущего воспроизводимого диска MP3 отображается список папок.
При выборе текущей папки также отображается список дорожек. ( 27)
Выберите дорожку, чтобы начать воспроизведение.
1
Войти в меню <Search Mode> можно, когда выбрано “HEAD MODE”.
*
Доступные режимы поиска зависят от типа используемого iPod/iPhone.
Dual Zone (Двойная Зона)
Операции в режиме “Dual Zone”, 43.
28
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.