JVC KD-AVX33 User Manual [en, de, fr]

DVD/CD RECEIVER

DVD-/CD-RECEIVER RÉCEPTEUR DVD/CD DVD/CD-RECEIVER

KD-AVX33

For canceling the display demonstration, see page 5. Zum Abbrechen der Displaydemonstration siehe Seite 5. Pour annuler la démonstration des affichages, référez-vous à la page 5. Zie bladzijde 5 voor het annuleren van de displaydemonstratie.

ENGLISH

DEUTSCHFRANÇAIS

NEDERLANDS

For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l’installation et les raccordements, se référer au manuel séparé. Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

LVT1659-001A

[E]

Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC

0536

English: Español:

Hereby, JVC, declares that this KD-AVX33 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/ EC.

Deutsch: Ελληνική:

Hiermit erklärt JVC, dass sich das Gerät KD-AVX33 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/ EG befindet. (BMWi)

Hiermit erklärt JVC die Italiano: Übereinstimmung des Gerätes

KD-AVX33 mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG befindet. (Wien)

Français: Malti:

Par la présente JVC déclare que l’appareil KD-AVX33 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Nederlands: Português:

Hierbij verklaart JVC dat het toestel KD-AVX33 in overeenstemming is

met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Dansk: Suomi:

Undertegnede JVC erklærer herved, at følgende udstyr KD-AVX33 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Por medio de la presente JVC declara que el KD-AVX33 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ JVC ∆ΗΛΩΝΕΙ ΟΤΙ KD-AVX33 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.

Con la presente JVC dichiara che questo KD-AVX33 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Hawnhekk, JVC, jiddikjara li dan KD-AVX33 jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/ EC.

JVC declara que este KD-AVX33 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

JVC vakuuttaa täten että KD-AVX33 tyyppinen laite on direktiivin 1999/5/ EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska: Lietuviu:

Härmed intygar JVC att denna KD-AVX33 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Íslenska: Magyar:

Hér með lýsir JVC yfir því að KD-AVX33 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Norsk: Polski:

JVC erklærer herved at utstyret KD-AVX33 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Cesky: Slovensko:

JVC tímto prohlašuje, že tento KD-AVX33 je ve shodě se základními požadavky a dalšími príslušnými ustanoveními směrnice 1999/5/ES.

Eesti: Slovensky:

Käesolevaga kinnitab JVC seadme KD-AVX33 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Latviski:

Ar šo JVC deklarē, ka KD-AVX33 atbilst Direktīvas 1999/5/EK būtiskājam prasībām un citiem ar to saistītajiem noteikumiem.

Šiuo JVC deklaruoja, kad šis KD-AVX33 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Alulírott, JVC nyilatkozom, hogy a KD-AVX33 megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Niniejszym JVC oświadcza, że KD-AVX33 jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

JVC izjavlja, da je ta KD-AVX33 v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ ES.

JVC týmto vyhlasuje, že KD-AVX33 spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

WARNINGS:

This symbol is only valid in the European Union.

Information for Users on Disposal of Old Equipment

This symbol indicates that the product with this symbol should not be disposed as general household waste at its end-of-life. If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country and municipality. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health.

To prevent accidents and damage

• DO NOT install any unit and wire any cable in locations where;

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety devices

such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

If you need to operate the unit while driving, be

sure to look around carefully.

• The driver must not watch the monitor while driving.

• The driver must not put on the headphones while driving.

Cautions on the monitor:

• The monitor built in this unit has been produced with high precision, but it may have some ineffective dots. This is inevitable and is not malfunction.

• Do not expose the monitor to direct sunlight.

• When the temperature is very cold or very hot. – Chemical changes occur inside, causing

malfunction.

– Pictures may not appear clearly or may move

slowly. Pictures may not be synchronized with the sound or picture quality may decline in such environments.

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

How to reset your unit

Contents

INTRODUCTION

Playable disc type ............................ 4

Before operating the unit ................ 5

ENGLISH

• Your preset adjustments (except for the registered

Bluetooth devices) will also be erased.

How to forcibly eject a disc

NO EJECT?

EMERGENCY EJECT?

NO EJECT?

EMERGENCY EJECT?

• If this does not work, reset the unit.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

OPERATIONS

Basic operations—Control panel ...... 7

Basic operations—

Remote controller (RM-RK251) ...... 8

Listening to the radio ...................... 10

Disc operations ................................ 15

Dual Zone operations ....................... 28

USB operations ................................ 31

Bluetooth® operations—

Cellular phone/audio player .......... 33

EXTERNAL DEVICES

Listening to the CD changer .............. 40

Listening to the DAB tuner ............... 42

Listening to the iPod/D.player .......... 45

Listening to other external

components ................................. 46

SETTINGS

Sound equalization .......................... 48

Assigning titles to the sources .......... 49

Menu operations ............................. 50

REFERENCES

Maintenance ................................... 60

More about this unit ........................ 61

Troubleshooting .............................. 66

Specifications .................................. 70

Playable disc type

Disc type Recording format, file type, etc. Playable

DVD DVD Video (Region Code: 2)*

ENGLISH

DVD Audio

DVD-ROM

DVD Recordable/Rewritable (DVD-R*2/-RW, +R/+RW*3)

• DVD Video: UDF bridge

• DVD-VR

• DivX/MPEG1/MPEG2/JPEG/MP3/ WMA/WAV/AAC: Compliant to ISO 9660 level 1, level 2, Romeo, Joliet

DVD Video

DVD-VR (non-CPRM only)

DivX/MPEG1/MPEG2

JPEG

MP3/WMA/WAV/AAC*

MPEG4

DVD+VR

• DVD-RAM cannot be played.

Dual Disc DVD side

Non-DVD side

CD/VCD Audio CD/CD Text (CD-DA)/DTS-CD

VCD (Video CD)

CD-ROM

CD-I (CD-I Ready)

CD Recordable/Rewritable (CD-R/-RW)

• Compliant to ISO 9660 level 1, level 2, Romeo, Joliet

CD-DA

MP3/WMA/WAV/AAC*

JPEG

DivX/MPEG1/MPEG2

MPEG4

*1 If you insert a DVD Video disc of an incorrect Region Code, “Region code error” appears on the monitor. *2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). *3 It is possible to play back finalized +R/+RW (Video format only) discs. However, the use of +R double layer disc is not recommended. *4 This unit can play back AAC files encoded using iTunes.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

Before operating the unit

Cancel the display demonstration and set the clock. (☞ also pages 51 and 52)

• Operations are explained mainly using the buttons on the unit; however, the buttons on the remote controller can work in the same way if they have the same names or marks.

Setup menu icon

AV Menu

ENT

Setup

Currently selected menu

Enter

Indication language:

In this manual, English indications are used

~ Turn on the power. Ÿ Display <AV Menu>.

for purpose of explanation. You can select the indication language on the monitor. (☞ page 52)

! Enter the <Setup> menu. ⁄ Select <Display> ] <Demonstration>, then activate the <Demonstration> screen.

Setup Display Demonstration

Display

Clock Disc Setup 1 Disc Setup 2 Tuner

Demonstration

Currently selected submenu Current setting

Demonstration

Wall Paper Scroll Tag Display Dimmer

Off

ENT

Exit

ENGLISH

@ Cancel the display demonstrations.

Select <Off>.

Demonstration

Off

ENT

Exit

Continued on the next page

INTRODUCTION

ENGLISH

(twice)

Clock

Time Set

12Hours/24Hours OSD Clock Clock Adjust

0:00

¤ Return to the <Setup> menu. # Select <Clock> ]<Time Set>, then

activate the <Time Set> screen.

‹ Set the clock time.

Time Set

Hours

18 : 00

ENT

Exit

Time Set

Minutes

18 : 35

ENT

Exit

$ Return to the <Clock> menu. › Select <12Hours/24Hours>. % Activate the <12Hours/24Hours>

screen.

ﬁ Select either the 12-hour or 24-hour

system.

12Hours/24Hours

12 Hours

24 Hours

ENT

Exit

^ Return to the <Clock> menu. ﬂ Select <Clock Adjust>. & Activate the <Clock Adjust> screen. ‡ Select the <Clock Adjust> setting.

• Off: Cancels.

• Auto: Activate auto clock adjustment using the clock time (CT) data from an FM RDS station.

* Finish the procedure.

To display the clock time while playing back a video source, select <Clock> = <OSD Clock> = <On>.

Basic operations — Control panel

Select the source. TUNER = DAB = DISC (DVD/VCD/CD) = USB =CD-CH, iPod, D.PLAYER, or EXT-IN =Bluetooth Phone

=Bluetooth Audio = AV-IN =(back to the beginning)

• You cannot select these sources if they are not ready.

• Turn on the power.

• Turn off the power

• Display or erase <AV Menu>*

• Activate Voice Dialing [Hold].

[Hold].

• Attenuate the sound (if the power is on).

Adjust the volume.

Activate TA Standby Reception.

Show PTY preset list [Hold].

Change the display information.

Remote sensor

ENGLISH

• Eject the disc.

• Change the control panel tilt (Tilt1 – Tilt4)

[Hold, then press].

• Display <Dial Menu>.

• DISC/USB: Start playback.

• On menus: Enter. (

ENT

:[Hold])

• TUNER/DAB: Select the bands.

• DISC/USB: Stop playback.

• On menus: Back.

• Display <Redial> list [Hold].

4 / ¢

• TUNER/DAB: Search for stations/ensembles.

• DISC/USB: Select chapters/tracks.

• On menus: Go to previous/next step.

• iPod/D.PLAYER: Select tracks.

• Bluetooth Audio: Reverse skip/forward skip.

5 / ∞*

• TUNER: Select preset stations.

• DAB: Select services.

• DISC/USB: Select titles/folders.

• On menus: Select items.

• iPod/D.PLAYER: Enter player’s menu/pause or stop playback.

• Bluetooth: Select a device.

Display window

ENT

:[Press]/

<AV Menu> screens

You can use the menus to set up various settings. The <AV Menu> screen consists of the following sub-menus—Setup/Equalizer/Sound/Disc Surround/Mode/List/Bluetooth/Dual Zone.

• For details, see pages 50 to 59.

*2 To attach the control

panel

By holding 5 / ∞, you can display the list

accessible for the selected source.

Reset the unit.

• Use only when the internal system malfunctions.

Detach the control

panel*

OPERATIONS

Basic operations — Remote controller (RM-RK251)

Installing the battery

ENGLISH

If the range or effectiveness of the remote controller decreases, replace both batteries.

Before using the remote controller:

• Aim the remote controller directly at the remote sensor on the unit.

• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).

The unit is equipped with the steering wheel remote control function.

• See the Installation/Connection Manual (separate

volume) for connection.

R03/LR03/AAA

Caution:

• Do not expose batteries to heat or flame.

Main elements and features

;

a s

IMPORTANT:

If Dual Zone is activated (☞ page 28), the remote controller functions only for operating the DVD/CD player.

1*1 • Turns on the power.

• Attenuates the sound if the power is on.

• Turns off the power if pressed and held (while the power is on).

2*1 Selects the source. 3*1 • Displays <Dial Menu>.

• Displays <Redial> list if pressed and held.

• Answers incoming calls.

4*1*2 Adjusts the volume level. 5*1*2 Selects surround mode. 6 • DVD/DivX 6: Shows the disc menu.

• VCD: Resumes PBC playback (☞ page 23).

• DVD-VR: Shows the Original Program screen.

7 • Makes selection/settings.

• ~: Skips back or forward by 5 minutes for

DivX/MPEG1/MPEG2.

• DISC +/– buttons: Changes discs for “CD-CH.”

8 Shows the on-screen bar.

Changes the display information.

p Display or erase <AV Menu>. q For disc/USB operations:

• 6: Plays/pauses.

• 5 / ∞ DVD: Selects the title/group. DVD-VR: Selects the program/play list. USB/other discs (except VCD/CD): Selects the

folders.

• 4 / ¢:

– Press briefly: reverse skip/forward skip – Press and hold: reverse search/forward search

For FM/AM operations:

• 5 / ∞: Selects the preset stations.

• 4 / ¢: Functions to search for stations.

– Press briefly: Auto Search – Press and hold: Manual Search

For DAB tuner operations:

• 5 / ∞: Selects a service.

• 4 / ¢: Functions to search for

ensembles. – Press briefly: Auto Search – Press and hold: Manual Search

For Apple iPod/JVC D. player operations:

• ∞: Pauses/stops or resumes playback.

• 5: Enters the main menu (then 5 / ∞ / 4 / ¢ work as the menu selecting

buttons).*

• 4 / ¢ (in menu selecting mode)

– Selects an item if pressed briefly. (Then, press

∞ to confirm the selection.)

– Skips 10 items at a time if pressed and held.

For Bluetooth operations:

• 5 / ∞: Selects a registered device.

• 4 / ¢: reverse skip/forward skip (for audio operation).

• 6: Answers incoming calls (for “Bluetooth Phone”). Plays/Pauses (for “Bluetooth Audio”).

On menus:

• 5 / ∞: Select items.

• 4 / ¢: Goes to previous/next step.

w TUNER/DAB: Selects the bands. DISC/USB: Stop playback. Bluetooth Phone: Ends the call. Bluetooth Audio: Plays/pauses. On menus: Back.

Adjusts the volume level through the 2nd AUDIO

OUT plug. (☞ page 28)

Activates or deactivates Dual Zone.

t*1*2 Selects the sound mode. y • DVD Video/DivX 6: Shows the disc menu.

• VCD: Resumes PBC playback. (☞ page 23)

• DVD-VR: Shows the Play List screen.

u RETURN button

• For VCD: Returns to the PBC menu.

i DISC/USB: Switches number entry mode.

• Also functions as CLEAR button to erase the misentry after entering the wrong number.

o Enter numbers. (☞ pages 12, 21 to 23, 38, and

43)

• CD changer: Selects the disc directly.

• Tuner: Selects the preset stations.

;*1 Changes the aspect ratio of the playback pictures. a Reverse search/forward search for disc/USB

operations

s • DVD Video: Selects audio language (

subtitles (

), angle ( ).

• DVD Audio: Selects audio stream ( ).

• DVD-VR: Turn on/off subtitles ( ) and selects audio channel( ).

• DivX: Selects audio language ( ), subtitles (

• VCD: Selects audio channel ( ).

*1 If Dual Zone is activated, these buttons cannot be

used.

*2 These buttons can be used only when the slide cover is

closed.

*3 5 : Returns to the previous menu. ∞ : Confirms the selection.

ENGLISH

OPERATIONS

Listening to the radio

POWER]ON

Preset No.Band

PS (station name) for FM RDS. If no signal is coming in, “No Name” appears.

ENGLISH

FLAT

Pop M

DXMOAFTP

15: 45

PTY code for FM RDS

Select “TUNER.”

TUNER

FM1 Preset1

Bayern Radio

87.5 MHz

Tuner/Standby Reception indicators

Ÿ Select the bands.

! Search for a station—Auto Search.

• Manual Search: Hold either 4 or ¢ until “Manual Search” appears on the display, then press it

repeatedly.

• The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal strength.

When an FM stereo broadcast is hard to receive

AV Menu

Setup

AV Menu

ENT

Enter

Mono

Off

Reception improves, but stereo effect will be lost.

• The MO indicator lights up.

To restore stereo effect, select <Off > in step 4.

☞ page 48

ENT

Exit

Mode

Mode menu icon

Mode

Mono

DX/Local SSM PTy Standby

Off

ENT

Enter

Tuning in to stations with sufficient signal strength

This function works only for FM bands. Once you have activated this function (selected <Local>), it always works when searching for FM stations.

AV Menu

Setup

AV Menu

ENT

Enter

AV Menu

Mode

Mode menu icon

Mode

Mono DX/Local

SSM

PTy Standby

ENT

Enter

ENT

Start

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

ENGLISH

ENT

Mode

Enter

Mode menu icon

Mode

DX/Local

Mono

DX/Local

SSM PTy Standby

Local

ENT

Exit

Only stations with sufficient signal strength will be detected.

• The DX indicator goes off, then the LO indicator lights up.

FM station automatic presetting —SSM (Strong-station Sequential Memory)

This function works only for FM bands. You can preset six stations for each band.

AV Menu

Setup

ENT

Enter

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

2 Tune in to a station you want to preset.

No Name

92.5 MHz

Select a preset number.

The station selected in step 2 is now stored in preset number 4.

* Each time you hold the button, you can change

the FM bands.

• Preset List can also be accessed through <AV

Menu> = <List>. (☞ page 12)

FM1 Store

87.5

89.9

97.9

105.9

108.0

107.9

Preset List appears.*

FM1 Store

87.5

89.9

97.9

105.9

108.0

107.9

TUNER

FM1 Preset4

No Name

92.5 MHz

OPERATIONS

ENT

Selecting preset stations

On the remote:

The following features are available only for FM RDS stations.

ENGLISH

On the unit:

• Each time you hold the button, you can change the FM bands.

• Preset List can also be accessed through <AV

FM1 Store

87.5

89.9

97.9

92.5

108.0

107.9

Menu> = <List>.

AV Menu

Setup

AV Menu

List

List menu icon

FM1 Store

ENT

Searching for FM RDS programme—PTY Search

You can search for your favorite programmes being broadcast by selecting the PTY code for your favorite programmes.

Available PTY codes appear (including six preset PTY codes).

2 Select a PTY code.

1 2 3 4 5 6

87.5

89.9

97.9

92.5

108.0

107.9

ENT

Enter

If there is a station broadcasting a programme of the same PTY code as you have selected, that station is tuned in.

Available PTY codes:

News, Current Affairs, Information, Sport, Education, Drama, Cultures, Science, Varied Speech, Pop Music, Rock Music, Easy Listening, Light Classics M, Serious Classics, Other Music, Weather & Metr, Finance, Children’s Progs, Social Affairs, Religion, Phone In, Travel & Touring, Leisure & Hobby, Jazz Music, Country Music, National Music, Oldies Music, Folk Music, Documentary

PTy Search

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

PTy Search

Cultures

Science

Varied Speech Pop Music Rock Music Easy Listening

TUNER

FM1

PTy Search XX.X MHz

FLAT

Science

DXAF

ENT

15: 45

Frequency changes as search goes on.

Storing your favorite programme types

You can store your favorite PTY codes into the PTY Preset List.

PTy Search

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

ENT

Available PTY codes appear (including six preset PTY codes).

2 Select a PTY code to store into the List.

PTy Search

Cultures

Science

Varied Speech Pop Music Rock Music Easy Listening

ENT

Current PTY Preset List is shown on the display.

PTy Memory

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

ENT

3 Select a listed code to be replaced with the

one newly selected.

PTy Memory

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

Now <Current Affairs> is replaced with <Science>.

ENT

Activating/deactivating TA/PTY Standby Reception

TA Standby Reception Indicator

Press

to activate.

The unit will temporarily switch to Traffic Announcement (TA), if available, from any source other than AM.The volume changes to the preset TA volume level if the current level is lower than the preset level (☞ page

54).

Not yet activated. Tune in to another station providing the RDS signals.

Press

to deactivate.

PTY Standby Reception Indicator

Activate <AV Menu>, then select <Mode>, <PTy Standby> (☞ pages 14, 57).

The unit will temporarily switch to your favorite PTY programme from any source other than AM.

Not yet activated. Tune in to another station providing the RDS signals.

To deactivate, select <Off> in step 4, then press ENT once (☞ page 14).

Lights up

Flashes

Goes off

PTY

Lights up

Flashes

Goes off

ENGLISH

• When a DAB tuner is connected, TA Standby/PTY Standby Reception also works for the DAB tuner.

OPERATIONS

Activating PTY Standby Reception

ENGLISH

AV Menu

Setup

AV Menu

Tracing the same programme— Network-Tracking Reception

When driving in an area where FM reception is not

ENT

Enter

sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals.

ENT

Mode

Enter

Mode menu icon

Select a PTY code for PTY Standby Reception.

Mode

Mono DX/Local SSM

PTy Standby

Off

PTy Standby

Off

News

PTy Standby

Drama Cultures

Science

Varied Speech Pop Music

ENT

Exit

Programme A broadcasting on different frequency areas (01 – 05)

When shipped from the factory, Network-Tracking Reception is activated.

To change the Network-Tracking Reception setting, see <AF Regional> on page 54.

• When the DAB tuner is connected, refer also to

“Tracing the same programme—Alternative Frequency Reception (DAB AF).” (☞ page 44)

Automatic station selection— Programme Search

Usually when you select preset stations, the preset station is tuned in. If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another frequency broadcasting the same programme as the original preset station is broadcasting. (☞ page 54)

• The unit takes some time to tune in to another

station using programme search.

Disc operations

The disc type is automatically detected, and playback starts automatically (for some discs: automatic start depends on its internal program).

If a disc does not have any disc menu, all tracks in it will be played repeatedly until you change the source or eject the disc.

” appears on the monitor, the unit cannot accept the operation you have tried to do.

If “

• In some cases, without showing “ ,” operations will not be accepted.

Insert the disc.

Playback starts automatically.

Label side

Caution:

Do not place your finger behind the control panel.

Caution on volume setting:

Discs and connected USB devices produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

ENGLISH

0: Eject the disc.

7: Stop playback.

DISP: Press if no playback picture appears, but disc information

screen (

☞ pages 16 to 18) is displayed.

DISC

Now Reading ...

3: Start playback if necessary.

15: 45

OPERATIONS

While playing the following discs, press .

• Each time you press the button, playback picture and disc information screens appear alternately.

Disc type

Audio format

Surround mode

ENGLISH

MULTI

DVD

DIGITALVIDEO

T 01 C 02 0:45:38

CHAP. RPT

15: 45

4 ¢ Press: Select chapter Hold: Reverse/forward search 5 ∞ Select title

DVD

4 ¢ Press: Select chapter Hold: Reverse/forward search 5 ∞ Select program no./Play List no.

DVD

Playback mode

VR-PR: Original program VR-PL: Play List

P 01 C 02 0:45:38

AUDIO

G 01 02 0:45:38

Title no./Chapter no./ Playing time

FLATDIGITALVR-PR

15: 45

Program no. (or Play List no.)/Chapter no./Playing time

Group no./Track no./Playing time

MULTIMLP

BONUS

B.S.P

RPT

15: 45

4 ¢ Press: Select track Hold: Reverse/forward search 5 ∞ Select group

BONUS indicator

☞ page 24)

(

B.S.P indicator (☞ page 24)

DVD

DivX

T 01 C 02 0:45:38

Current Folder Name Current File Name.avi

FRONT 2CH

RPT

ENGLISH

15: 45

4 ¢ Press: Select track Hold: Reverse/forward search for DivX/MPEG 5 ∞ Press: Select folder Hold: Display Folder List

4 ¢ Press: Select track Hold: Reverse/forward search

*1 Search speed: x2 ] x10. *2 Search speed: ¡1 ] ¡2.

PBC indicator lights up when PBC is in use.

VCD

02 0:45:38

Track no./Playing time

For DivX/MPEG: Folder no./Track no./Playing time For JPEG: Folder no./File no.

☞ page 48

FLATPBC

15: 45

OPERATIONS

☞ page 48

ENGLISH

4 ¢ Press: Select track Hold: Reverse/forward search

Hold: Reverse/forward search 5 ∞ Press: Select folder Hold: Display Folder List

02 0:45:38 Disc Title Artist Name Current Track Title

(only for CD Text)

Audio format (MP3/WMA/WAV/AAC)

T 01 02 0:45:38

Current Folder Name Current File Name.mp3

FLAT

RPT

15: 45

Track no./Playing timeDisc title/Artist Name/Track title

☞ page 48

RPT

FLAT

15: 45

Folder no./Track no./Playing time4 ¢ Press: Select track

Tag Display> is set to

MP3

Tag data will be shown instead of folder/file names when they are recorded and < <

On>. (☞ page 51)

*1 Search speed: x2 ] x10. *3 “No Name” appears for conventional CDs.

Selecting playback modes

You can use only one of the following playback modes—Intro/Repeat/Random. Ex. To select Track Repeat

AV Menu

Mode

Off

All Off Intro

Repeat

Random

ENGLISH

Setup

AV Menu

ENT

Enter

Repeat

Off

Track

Folder

ENT

Set

When one of the playback modes is selected,

ENT

Mode

Mode menu icon

Enter

the corresponding indicator lights up on the disc

information screen. To cancel, select <All Off> in step 3 or <Off> in step 4.

Disc type Intro Repeat Random

Chapter: Repeats current

—

chapter

Title: Repeats current title

— Track: Repeats current track —

Chapter: Repeats current

chapter

—

Program: Repeats current

program (not available for Playlist playback)

Track: Plays the first 15

seconds of each track (for VCD: PBC not in use)

Track: Plays the first 15

seconds of each track

Folder: Plays the first 15

seconds of the first track of each folder

Track: Repeats current track

(for VCD: PBC not in use)

Track: Repeats current track Folder: Repeats all tracks of

the current folder

Disc (All): Randomly plays all

tracks (for VCD: PBC not in use)

Folder: Randomly plays all

tracks of current folder, then tracks of next folders

Disc (All): Randomly plays all

tracks

Track: Repeats current track

—

Folder: Repeats current folder

—

Folder: Repeats current folder

—

OPERATIONS

Selecting tracks on the list

If a disc includes folders, you can display the Folder/ Track (File) Lists, then start playback.

ENGLISH

Folder List

Off

My Best

Cinema Pops My Best2 Favorite Song Cinema2

ENT

Prohibiting disc ejection

You can lock a disc in the loading slot.

NO EJECT?

EMERGENCY EJECT?

“No Eject” appears.

Folder List appears.

• Hold the button to see the next/previous folders.

2 Select a folder, then activate the Track List.

Folder List

My Best Cinema Pops

My Best2

Favorite Song Cinema2

Off

ENT

Track List of the selected folder appears.

3 Select a track, and start playing.

File List

Song011.mp3 Song012.mp3 Song013.mp3

Song014.mp3

Song015.mp3 Song016.mp3

Off

• Folder List can also be accessed through <AV

Menu> = <List>.

AV Menu

Setup

AV Menu

List

List menu icon

ENT

Enter

ENT

Enter

To cancel the prohibition, repeat the same procedure to select “EJECT OK?”.

Operations using the remote controller—RM-RK251

: Stop playback.

: Start playback/Pause (if pressed during playback).

: Reverse/forward search.*2 (No sound can be heard.)

(Slow motion*3 during pause. No sound can be heard.)

: Press: Select chapter (during playback or pause).

Hold: Reverse/forward search.*

: Select title (during playback or pause).

ENGLISH

*1 Erases the misentry of the

number.

*2 Search speed: x2 ] x5 ]

x10 ] x20 ] x60

*3 Slow motion speed: 1/32 ]

1/16 ] 1/8 ] 1/4 ] 1/2

*4 Search speed: x2 ] x10

= = :

Select chapter. Select title (when not playing).

(twice) = = :

Select title (during playback or pause).

Using menu driven features

1 2 Select an item you want

to start playback.

: Select aspect ratio.

: Select audio language.

: Select subtitle language.

: Select view angle.

: Stop playback.

: Start playback/Pause (if pressed during playback).

: Reverse/forward search.*

: Press: Select track.

Hold: Reverse/forward search.*

: Select group.

Using menu driven features

= = :

Select track.

(twice) = = :

1 2 Select an item you want

to start playback.

Select group.

: Select aspect ratio.

: Select audio stream.

OPERATIONS

ENGLISH

: Stop playback.

: Start playback/Pause (if pressed during playback).

: Reverse/forward search*2. (No sound can be heard.)

: Press: Select track.

Hold: Reverse/forward search*

. (No sound can be heard.)

: Select folder.

= = :

Select track (within the same folder).

(twice) = = :

Select folder.

: Select aspect ratio.

: Select audio language. (DivX only)

: Select subtitle language. (DivX only)

While playing...

Back/advance the scenes by 5 minutes.

: Stop playback.

: Start playback/Pause (if pressed during

playback).

: Reverse/forward search*4. (No sound

can be heard.)

(Slow motion*5 during pause. No sound

can be heard.)

Reverse slow motion does not work.

: Press: Select chapter (during playback

or pause).

Hold: Reverse/forward search*

: Select program. Select play list (during playback or pause).

: Select aspect ratio.

For DivX6: Using menu driven features

1 2 Select an item you want to

start playback.

Current playback position

2nd press

1st press

2nd press

3rd press

: Select audio channel

(ST: stereo, L: left, R: Right).

: Turn on/off subtitle.

= = :

Select chapter. Select program (when not playing).

(twice) = = :

Select program/play list (during playback or

pause).

Using Original Program/Play List screens

(☞ page 30) 1 For Original Programs: For Play List: 2 Select an item you want to start playback. 3 (Hide screen)

: Stop playback.

: Start playback. (Slide show: each file is

shown for a few seconds.)

Shows the current file until you change

it if pressed during Slide show.

: Select track.

: Stop playback.

: Start playback/Pause (if

pressed during playback).

: Reverse/forward search*4.

: Press: Select track.

Hold: Reverse/forward search*6.

ENGLISH

: Select folder.

: Select aspect ratio.

= = :

Select track (within the same folder).

(twice) = = :

Select folder.

: Stop playback.

: Start playback/Pause (if pressed during

playback).

: Reverse/forward search*4.

(Forward slow motion*5 during pause. No

sound can be heard.)

Reverse slow motion does not work.

: Press: Select track.

Hold: Reverse/forward search*6 (No sound

can be heard.) : Select aspect ratio. : Select audio channel (ST: stereo, L: left, R:

Right).

: Stop playback.

: Start playback/Pause (if pressed during

playback).

: Reverse/forward search*4.

: Press: Select track.

Hold: Reverse/forward search*6.

= = : Select track.

: Select folder.

= = :

Select track (within the same folder).

(twice) = = :

Select folder.

= = :

Select track.

During PBC playback...

= = :

Select an item on the menu. To return to the previous menu, press

To cancel PBC playback

2 Start the desired track.

= =

• To resume PBC, press / .

*1 Erases the misentry of the number. *2 Search speed: ¡1 ] ¡2 ] ¡3 *3 Search speed: ¡1 ] ¡2 *4 Search speed: x2 ] x5 ] x10 ] x20 ] x60 *5 Slow motion speed: 1/32 ] 1/16 ] 1/8 ]

1/4 ] 1/2

*6 Search speed: x2 ] x10

OPERATIONS

Playing back a bonus group

If a DVD Audio including a “bonus group” is detected, the BONUS indicator lights up on the disc information screen.

ENGLISH

To play a bonus group...

1 Select the bonus group.

• The bonus group is usually recorded as the last

group.

2 Enter the key number.

: Move the entry position

: Select a number

• “key number” (a kind of password) for the bonus

group is not open to public. The way of getting the key number depends on the disc.

3 Follow the interactive instructions shown on

the monitor.

Selecting browsable still picture

When a disc including browsable still pictures is detected, the B.S.P indicator lights up on the disc information screen.

When disc shows the BSP selecting icons such as @ or # on the screen...

1 Select an item you want to display.

Enjoying surround sounds

You can enjoy multi-channel surround playback through the front, center, surround speakers.

• After connecting the center speaker, make

sure to activate the center speaker; otherwise, no sound comes out of the center speaker (☞

page 53).

• All surround mode can also be used for “USB.”

MULTI: For multi-channel encoded sources such

as Dolby Digital* (When activated, “MULTI” is shown on the disc information screen.)

Dolby Pro Logic II (Movie/Music): For 2 channel

sources except for DivX/MPEG 1/MPEG2 discs.

To turn on the surround

, DTS*2, and DVD Audio.

AV Menu

Setup

Disc Surround menu icon

AV Menu

Disc Surround

Surround Off

Surround On

ENT

Enter

Auto

• Surround Off: Deactivates surround.

• Surround On: Activates surround = go to the

following steps.

Surround On

Auto

Through Dolby PLII Movie Dolby PLII Music

ENT

Set

• Auto: When multi-channel digital signals come in, “MULTI” surround is activated.

When 2-channel or 2.1-channel signals come in,

“4CH STEREO” is activated.

• Through: All incoming channel signals are sent to the corresponding speakers.

• Dolby PLII Movie: Activates Dolby Pro Logic II Movie.

• Dolby PLII Music: Activates Dolby Pro Logic II Music. You can adjust <Panorama> and <Center Width> settings. (☞ below)

To change the <Dolby PLII Music> setting

in step 4 above...

Surround On

Auto Through Dolby PLII Movie

Dolby PLII Music

Panorama

Dolby PLII Music

Panorama

CenterWidth

On the remote controller:

• You cannot change the <Dolby PL II Music> settings using the remote controller.

*1 Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

*2 “DTS” and “DTS Digital Surround” are registered

trademarks of DTS, Inc.

ENGLISH

• Panorama: Select <On> to add wraparound sound effect.

• Center Width: Adjust the center image so it may be heard only from the center speaker, only form the left/right front speaker as a “phantom” center image, or various combination of these speakers. As the number increases, the “phantom” effect becomes stronger (normally select <4>).

OPERATIONS

Operations using the on-screen bar (DVD/VCD/DivX/MPEG1/MPEG2/ JPEG)

These operations are possible on the monitor using the remote controller.

ENGLISH

1 Display the on-screen bar. (☞ page 27)

2 Select an item.

3 Make a selection.

If a pop-up menu appears...

• For entering time/numbers...

To remove the on-screen bar

: Move the entry position

: Select a number

On-screen bar

Information

Operation

DVD -V

TIME TITLE CHAP

T02-C03 TOTAL 1:25:58

C. RPT

RPT

Above example is of DVD Video. Items shown on the bar vary due to the disc type.

1 Disc type 2 • DVD: Audio signal format

• VCD: PBC

3 Playback mode*

DVD Video: T. RPT: Title repeat C. RPT: Chapter repeat DVD Audio: T. RPT: Track repeat DVD-VR: C. RPT: Chapter repeat PG. RPT: Program repeat DivX/MPEG: T. RPT: Track repeat F. RPT: Folder repeat JPEG: F. RPT: Folder repeat VCD: T. INT: Track intro T. RPT: Track repeat A. RND: All random 4 Playback information

Current title/chapter

T02-C03

Current group/track

G02-T03 PG-001

C-002

Current program/chapter

PL-003

C-004

Current playlist/chapter

TRACK 01

Current track

Current folder/track

F001-T001 F002-F002

Current folder/file (JPEG)

5 Time indication

Elapsed playing time of the disc

TOTAL

Remaining title time (for DVD)

T. REM

Remaining disc time (for others)

TIME

Elapsed playing time of the current

chapter/track*

REM

Remaining time of the current

chapter/track*

6 Playback status

Play

Reverse/forward search

Reverse/forward slow-motion Pause Stop

7 Operation icons

Change time indication (see 5)

TIME

Time Search (Specify a certain scene

by entering time.)

TITLE

Title Search (by its number)

CHAP

Chapter Search (by its number)

GROUP

Group Search (by its number)

TRACK

Track Search (by its number)

RPT

Repeat play*

INT

Intro play*

RND

Random play*

Change the audio language, audio

channel or audio stream Change the subtitle language Change the view angle

PAGE

Change the browsable still pictures

(pages)

ENGLISH

*1 ☞ page 19 *2 Not applicable for DVD-VR.

OPERATIONS

Dual Zone operations

You can enjoy a disc playback on the external monitor connected to the VIDEO OUT and 2nd AUDIO OUT plugs, while listening to any other source than “USB” through

ENGLISH

the speakers.

• When Dual Zone is in use, you can only operate the DVD/CD player using the remote controller.

AV Menu

Setup

AV Menu

Dual Zone

Dual Zone menu icon

Dual Zone

Off On

On/Surround On

ENT

Enter

ENT

Enter

ENT

Set

• Off: Deactivates Dual Zone.

• On (DUAL): Activates Dual Zone without applying Headphone Surround*1.

• On/Surround On (DUAL-S): Activates Dual Zone and applies Headphone Surround.

When Dual Zone is activated, the main source is changed to “DISC.”

DVD

T 01 C 02 0:45:38

FLATDIGITALVIDEO

DUAL-S

Ex. When “On/Surround On” is selected.

To select a different source (main source) to listen through the speakers:

Press SRC (source) on the control panel.

• By using the buttons on the control panel, you can operate the newly selected source without affecting Dual Zone (DISC) operations.

• You cannot select “USB” for the main source.

On the remote controller:

2 Adjust the volume through the 2nd AUDIO

OUT plug.

3 Operate the DVD/CD player.

*1 JVC original headphone virtual surround system. This

surround will also work for the main source “DISC” if “On/Surround On” is selected as the sub-source. This surround does not work for DivX/MPEG1/MPEG2 discs.

*2 Displayed being shaded if Headphone Surround is not

applied.

Operations using the control screen

For discs except DVD and VCD:

While Dual Zone is on, these operations are possible on the external monitor using the remote controller. The control screen automatically appears when you insert a disc. (For DivX/MPEG1/MPEG2/JPEG; while not playing.)

TIME 00:00:14T. RPT

Track : 6 / 14 (Total 41)

Cloudy.mp3 Fair.mp3 Fog.mp3 Hail.wma Indian summer.mp3 Rain.mp3

Shower.mp3

Snow.mp3 Thunder.wma Typhoon.mp3 Wind.mp3 Winter sky.mp3

Folder : 2 / 3

01 Music

02 Music

03 Music

Track Information Album Weather Artist Robert M. Smith Title Rain

Ex.: MP3/WMA

1 Current folder (highlighted bar) 2 Current folder number/total folder number 3 Folder list

* If tag data includes “Jacket Picture” (baseline JPEG), it

will be displayed. If you press OSD, the playback mode selection window appears. (☞ below)

4 Selected playback mode (☞ below) 5 Elapsed playing time of the current track (not

displayed for JPEG)

6 Operation status 7 Current track number/total number of tracks in the

current folder (total number of tracks on the disc)

8 Track information (only for MP3/WMA/WAV/AAC) 9 Track list p Current track (highlighted)

To select a folder or track

1 Select “Folder” column or “Track” column on

the control screen.

2 Select a folder or track.

• If necessary, press ENT to start playback.

TIME 00:14

Track : 6 / 14

Cloudy Fair Fog Hail Indian summer

Rain

Shower Snow Thunder Typhoon Wind Winter sky

MODE

REPEAT

TRACK

Track Information

Album Four seasons Artist Robert M. Smith Title Rain

T. RPT

Ex.: CD Text

1 Playback mode selection window: appears when

OSD is pressed (☞ below).

2 Selected playback mode (☞ below) 3 Elapsed playing time of the current track 4 Operation status 5 Current track number/total number of tracks on the

disc

6 Track information 7 Track list 8 Current track (highlighted bar)

To select a track

• If necessary, press ENT to start playback.

ENGLISH

Selecting playback modes

You can also change the playback modes using the playback mode selection window.

• For CD/MP3/WMA/WAV/AAC: Intro/Repeat/ Random

• For DivX/MPEG1/MPEG2/JPEG: Repeat

2 Only for CD/MP3/WMA/WAV: Select a

playback mode.

3 Select your desired option.

Selected playback mode

DivX/MPEG1/MPEG2/JPEG: ☞ page 27 MP3/WMA/WAV/AAC: T. INT: Track intro F. INT: Folder intro T. RPT: Track repeat F. RPT: Folder repeat F. RND: Folder random A. RND: All random CD: T. INT: Track intro T. RPT: Track repeat A. RND: All random

OPERATIONS

Operations using the list screen

For discs except DVD, VCD, and CD

While Dual Zone is on, these operations are possible on the external monitor using the remote controller.

ENGLISH

While not playing...

1 Display the list screen.

Folder : 144/240 Track 144/198 Page : 4/7 fol120

fol121 fol122 fol123 fol124 fol125 fol126 fol127 fol128 fol129

fol130 fol131 fol132 fol133 fol134 fol135 fol136 fol137 fol138 fol139

fol140 fol141 fol142

fol143

fol144 fol145 fol146 fol147 fol148 fol149

fol150 fol151 fol152 fol153 fol154 fol155 fol156 fol157 fol158 fol159

List screen for DVD-VR

You can use Original Program and Play List screen anytime while playing DVD-VR with its data recorded.

• These screens can be displayed on the built-in monitor and the external monitor.

1 Display the Original Program/Play List

screen.

ORIGINAL PROGRAM

No Date Ch ime itle

1 25/04/07 4ch 19:00 JVC DVD World 2004 2 17/05/07 8ch 10:30 3 22/05/07 8ch 17:00 Music Festival 4 26/05/07 L-1 13:19 children 001 5 20/06/07 4ch 22:00 6 25/06/07 L-1 8:23 children 002

2 Select a folder on the list.

Folder : 144/240 Track 144/198 Page : 4/5 file0121.mp3

file0122.mp3 file0123.wma file0124.mp3 file0125.mp3 file0126.wma file0127.wma file0128.mp3 file0129.mp3 file0130.wma

file0131.mp3 file0132.mp3 file0133.mp3 file0134.mp3 file0135.wma file0136.mp3 file0137.wma file0138.mp3 file0139.wma file0140.wma

file0141.wma file0142.mp3 file0143.wma

file0144.mp3

file0145.mp3 file0146.mp3 file0147.mp3 file0148.wma file0149.wma file0150.wma

file0151.wma file0152.mp3 file0153.wma file0154.mp3 file0155.wma file0156.wma file0157.wma file0158.wma file0159.mp3 file0160.wma

3 Select a track on the list.

• To go back to the folder list, press .

1 Current folder number/total folder number 2 Current track number/total number of tracks in the

current folder

3 Current page/total number of the pages included

in the list

4 Current folder/track (highlighted bar)

PLAY LIST

No Date Chap Length Title

1 25/05/07 001 1:03:16 My JVC World 2 17/06/07 005 1:35:25 3 20/06/07 003 0:10:23 Favorite music 4 25/06/07 001 0:07:19 children001-002

2 Select an item you want.

1 Program/Play list number 2 Recording date 3 Recording source (TV station, the input terminal

of the recording equipment, etc.)

4 Start time of recording 5 Title of the program/play list* 6 Highlighted bar (current selection) 7 Creating date of play lists 8 Total number of chapters 9 Playback time

* The title of the original program or play list may

not be displayed depending on the recording equipment.

USB operations

You can connect a USB mass storage class device such as a USB memory, Digital Audio player*1, portable HDD, etc. to the unit.

~ Connect a USB device.

USB cable from the rear of the unit.

• You cannot connect a computer to the USB ( ) terminal of the unit.

Ÿ Select “USB”.

4 ¢ Press: Select track Hold: Reverse/forward search 5 ∞ Press: Select folder Hold: Display Folder List

USB

DISP: Press if no playback picture appears , but disc

information screen (

Now Reading ...

☞ pages 16 to 18) is displayed.

ENGLISH

7: Stop playback

This unit can play DivX/JPEG/MPEG1/MPEG2*2/MP3/ WMA/WAV/AAC*3 files stored in a USB mass storage class device.

• You can operate the USB device in the same way you

operate the files on discs. (☞ page 19 to 27)

• You cannot select “USB”when Dual Zone is in use.

• All tracks in the USB device will be played repeatedly until you change the source.

3: Start playback if necessary.

15: 45

*1 Except for JVC D. Player XA-HD500. *2 Except for MPEG2 files recorded by JVC Everio

camcorder (extension code <.mod>).

This unit can play back AAC files encoded using

iTunes. This unit cannot play back AAC files purchased from the iTunes Store.

OPERATIONS

Caution:

• Avoid using the USB device if it might hinder your safety driving.

• Do not pull out and attach the USB device repeatedly while “Now Reading...” is flashing on the monitor.

• Do not start the car engine if a USB device is connected.

• Stop play back before disconnecting a USB device.

ENGLISH

• Make sure all important data has been backed up to avoid losing the data.

• Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or cause damages to the device.

Selecting playback modes

You can use only one of the following playback modes—Intro/Repeat/Random. Ex. To select Track Repeat

AV Menu

ENT

Setup

Enter

AV Menu

ENT

Mode

Mode menu icon

Enter

Mode

Off

All Off Intro

Repeat

Random

Repeat

Off

Track

Folder

ENT

Set

When one of the playback modes is selected, the corresponding indicator lights up on the information screen.

To cancel, select <All Off> in step 3 or <Off> in step 4.

File type Intro Repeat Random

Track: Plays the first 15

seconds of each track

Folder: Plays the first 15

seconds of the first track of each folder

Track: Repeats current track Folder: Repeats all tracks of

the current folder

Folder: Randomly plays all

tracks of current folder, then tracks of next folders

USB (All): Randomly plays all

tracks

Track: Repeats current track

—

Folder: Repeats current folder

—

Bluetooth® operations — Cellular phone/audio player

Connecting a Bluetooth device for the first time

Bluetooth is a short-range wireless radio communication technology for the mobile device such as mobile phones, portable PCs, and other devices. The bluetooth devices can be connected without cables and communicate each other.

• The serial number is printed on the label placed on the bottom of the unit.

• Refer to the list (included in the box) to see the countries where you may use the Bluetooth® function.

Bluetooth profile

This unit supports the following Bluetooth profiles; HSP (Headset Profile) HFP (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile) SPP (Serial Port Profile) OPP (Object Push Profile)

Features

You can operate Bluetooth devices through the unit as follows:

• Receiving a call

• Making a call—from phone book, from call history (Redial/Missed Call/Received Call), by dialing number, by preset numbers, by voice command

• Receiving the SMS (Short Message Service)

• Play back a Bluetooth audio player

Refer also to the instructions supplied with the Bluetooth device.

• The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Victor Company of Japan, Limited (JVC) is under license. Other trademarks and trade names are those of their respective owners.

Pairing and PIN Code

When you connect a Bluetooth device to the unit for the first time, make pairing between the unit and the device. Pairing allows Bluetooth devices to communicate each other. To make pairing, you may need to enter the PIN (Personal Identification Number) code of your Bluetooth device you want to connect.

• Once the connection is established, it is registered in the unit even if you reset the unit. Up to five devices can be registered in total.

• Only one device can be connected at a time for each source (“Bluetooth Phone” and “Bluetooth Audio”).

• To use the Bluetooth function, you need to turn on Bluetooth function of the device.

Preparation: Operate the device to turn on its Bluetooth function.

Registration (Pairing) methods Use either of the following items in the <Bluetooth> menu to register and establish the connection with a device.

• Select “Bluetooth Phone” or “Bluetooth Audio” as the source to operate the <Bluetooth> menu.

<Open> Make the unit ready to establish

a new Bluetooth connection. Connection is established by operating the Bluetooth device.

<Search> Make the unit ready to establish

a new Bluetooth connection. Connection is established by operating the unit.

ENGLISH

Continued on the next page

OPERATIONS

Registering using <Open>

1 Select “Bluetooth Phone” or “Bluetooth

Audio.”

ENGLISH

Bluetooth Phone

NEW DEVICE

Select “NEW DEVICE” by pressing 5 / ∞.

FLAT

15: 45

AV Menu

ENT

Setup

Enter

AV Menu

ENT

Bluetooth

Bluetooth menu icon

Enter a PIN (Personal Identification

NEW DEVICE

Dial Menu Message

Open

Search Special Device

Number)* code to the unit.

• You can enter any number you like (1-digit to 16-digit number).

* Some devices have their own PIN code. Enter the

specified PIN code to the unit.

Enter

PIN Code

1234

7 Operate the target Bluetooth device. (While

“Open...” is flashing on the screen.) Enter the same PIN code (as entered in the above step) on the device to be connected.

Now connection is established and you can use the device through the unit.

The device remains registered even after you disconnect the device. Use <Connect> (or activate <Auto Connect>) to connect the same device from next time. (☞ pages 58 and 59)

Searching for available devices

Perform steps 1 to 3 on the left, then...

NEW DEVICE

Dial Menu Message

Open

Special Device

The unit searches for available devices and displays the list of them. (If no available device is detected, “Device Unfound” appears.)

2 Select a device you want to connect.

3 Enter the specific PIN code of the device to

the unit.

• Refer to the instructions supplied with the device

ENT

Enter

to check the PIN code.

• To delete an unwanted digit, select blank space.

4 Use the Bluetooth device to connect.

Now connection is established and you can use the device through the unit.

Connecting a special device

Perform steps 1 to 3 of “Registering using <Open>” on page 34, then...

NEW DEVICE

Dial Menu Message

Open Search

Special Device

Deleting a registered device

1 Select “Bluetooth Phone” or “Bluetooth

Audio,” then select a registered device you want to delete.

ENGLISH

The unit displays the list of the preset devices.

2 Select a device you want to connect.

3 Use <Open> (or <Search>) to connect.

Connecting/disconnecting a registered device

1 Select “Bluetooth Phone” or “Bluetooth

Audio,” then select a registered device you want to connect/disconnect.

2 Perform steps 2 and 3 of “Registering using

<Open>” on page 34, then...

• Select <Connect> to connect the selected device.

• Select <Disconnect> to disconnect the selected device.

2 Perform steps 2 and 3 of “Registering using

<Open>” on page 34, then...

• Select <Delete Pair>, then <Yes>.

You can set the unit to connect a Bluetooth device automatically when the unit is turned on. (☞ page

59)

OPERATIONS

Using the Bluetooth cellular phone

POWER]ON

Adjust the volume

Turns Blue when the Bluetooth device is connected.

ENGLISH

Press: Display <Dial Menu> Answers incoming call Hold: Display <Redial> list

Bluetooth Phone

Connected Device Name

~ Select “Bluetooth Phone.” Ÿ Enter the <Bluetooth> menu. ! Establish the connection with a device,

then make a call (or settings using the <Bluetooth> menu).

☞ pages 34, 50, 58, and 59

When the sound is stopped or interrupted during the use of a Bluetooth device, try the following

remedies.

• Turn off, then turn on the unit.

• (When the sound is not yet restored,) connect the

device again. (☞ “Connecting/disconnecting a registered device” on page 35)

When a call comes in...

FLAT

15: 45

Status of the device* Signal strength/Battery remainder

*1 You can adjust the volume level for “Bluetooth Phone”

without affecting the volume level for other sources.

*2 Appears only when the information comes from the

device.

*3 Each time you press 5 ∞, the registered device

name (and “NEW DEVICE” when a new device can be registered) appear in turn.

*4 When a cellular phone with audio function is

connected, appears.

You can adjust the microphone volume level. (☞ page

59)

To end the call or reject an incoming call

Hold any button (except ATT or +/–).

☞ page 48

Connected device name

Name and phone number (if acquired)

The source is automatically changed to “Bluetooth Phone.”

When <Auto Answer> is activated...

The unit answers the incoming calls automatically. (☞ page 59)

• When <Auto Answer> is deactivated, press any button (except ATT or +/–) to answer the incoming call.

Answering a waiting call

If your cellular phone is equipped with the call waiting function, you can put the current call on hold and answer the waiting call. Press any button (except ATT and +/–).

• To restore the on-hold call, press any button (except ATT and +/–) again.

• When you end one call, you can connect to the other.

When an SMS comes in...

If the cellular phone is compatible with SMS (Short Message Service) and <Message Info> is set to <Auto> (☞ page 59), the unit rings and “Receiving Message” appears on the monitor to inform you of the arrival of the message.

• You cannot edit or send a message through the unit.

When <Message Info> is set to <Auto>... To read the message

While “Receiving Message” is displayed...

• The source is changed to “Bluetooth Phone.”

To read the message later

• The message is stored into <Message>

= <Unread>. (☞ page 58)

When <Message Info> is set to <Manual>

Access the message list to read a message. (☞ page 58)

Making a call

1 Display the <Dial Menu>.

2 Select the method to make a call.

• Redial* : Shows the list of the phone numbers

• Received Calls* : Shows the list of the received

• Phonebook* : Shows the phone book of the

• Missed Calls* : Shows the list of the missed

• Phone Number : Shows the phone number

• Voice Dialing (Only when the connected

P902i

Redial

Received Calls Phonebook Missed Calls Phone number

Annie

P902i

Redial Received Calls

Phonebook

Missed Calls Phone number

Annie

you have dialed = go to the following step.

calls = go to the following step.

connected cellular phone = go to the following step.

calls = go to the following step.

entry screen = “How to enter phone number” on the next page.

cellular phone has the voice recognition system): Speak the name you want to call.

ENGLISH

* Displays only when your cellular phone is

equipped with these functions.

– If not displayed, please try to transfer the

phone book memory of the cellular phone to this unit. (Refer to the instruction manual supplied with your cellular phone.)

– With some cellular phones, the phone book

memory is transferred automatically.

3 Select the name/phone number you want to

call.

OPERATIONS

How to enter phone number

On the remote:

ENGLISH

On the unit:

Select a number. Move the entry position.

• To delete an unwanted digit, select blank space.

<Dial Menu> can be also accessed through <AV Menu> = <Bluetooth> = <Dial Menu>.

AV Menu

Setup

AV Menu

Bluetooth

Bluetooth menu icon

Dialling ...

Jack 09845671234

ENT

Enter

ENT

Enter

Presetting the phone numbers

You can preset up to six phone numbers.

1 Display the phone number you want to

preset by using one of <Dial Menu> items.

ENT

Jack

12312341234 09898765432

09845671234

Store

ENT

Dial

Ex.: “Jack” is selected from the phone book

Preset Memory list appears.

Preset Memory

11122223333

22233336666

44455556666

11133334444

99988887777

55566668888

ENT

2 Select a preset number.

Preset Memory

11122223333

22233336666

44455556666

11133334444

99988887777

55566668888

The phone number selected in step 1 is now stored in preset number 4.

ENT

To call a preset number

On the remote:

Direct operations to redial / Voice Dialing

You can use the following functions regardless of the current source.

To redial

To activate Voice Dialing

You can make a call by your voice.

Speak the name you want to call.

On the unit:

Preset List

1 2 3 4 5 6

Preset List

1 2 3 4 5 6

11122223333

22233336666 44455556666 09845671234 99988887777 55566668888

11122223333 22233336666 44455556666

09845671234

99988887777 55566668888

ENT

• Preset List can also be accessed through <AV

Menu> = <List>.

AV Menu

You can use the following buttons on the remote controller for the Bluetooth phone operations. For details, ☞ pages 8 and 9.

ENT

Setup

AV Menu

List

List menu icon

Enter

ENT

Enter

Using the Bluetooth audio player

Reverse/forward skip

POWER]ON

Pause

Turns Blue when the Bluetooth device is connected.

Bluetooth Audio

Connected Device Name

Status of the device* Signal strength/Battery remainder

~ Select “Bluetooth Audio.” Ÿ Start playback.

• See pages 33 to 35 for connecting a new device.

• See page 35 for connecting/disconnecting a registered device.

• See page 35 for deleting a registered device.

When the sound is stopped or interrupted during the use of a Bluetooth device, try the following

remedies.

• Turn off, then turn on the unit.

• (When the sound is not yet restored,) connect the device again. (☞ “Connecting/disconnecting a registered device” on page 35)

Bluetooth Information:

If you wish to receive more information about Bluetooth, visit our JVC web site.

FLAT

☞ page 48

15: 45

*1 Each time you press 5 ∞, the registered device

names (and “NEW DEVICE” when a new device can be registered) appear in turn. You cannot select “New Device” when a Bluetooth audio player is connected.

*2 Appears only when the information comes from the

device.

*3 Indicates the button pressed. It may be different from

the operation status.

*4 When a cellular phone with audio function is

connected, appears.

You can use the following buttons on the remote controller for the Bluetooth audio operations. For details, ☞ pages 8 and 9

OPERATIONS

ENGLISH

Listening to the CD changer

POWER]ON

ENGLISH

4 ¢ Press: Select track Hold: Reverse/forward search 5 ∞ Press: Select folder (MP3 only) Hold: Display Disc List

It is recommended to use a JVC MP3-compatible CD changer with your unit.

• You can play only CDs (CD-DA) and MP3 discs.

Preparation:

Make sure <Changer> is selected for the external input setting. (☞ page 55)

~ Select “CD-CH.” Ÿ Display the Disc List.

Disc List

MP3 DISC

DISC 02 DISC 03 DISC 04 DISC 05 DISC 06

Off

ENT

Disc no./Track no./Playing time

CD-CH

FLAT

01 01 0:02:38

Disc Title Artist Name Current Track Title

“No Name” appears for conventional CDs

• While playing an MP3 disc, you can select and start playing a track in the disc using the Lists: Disc List (select the current disc) = Folder List = File List, then start playing a track you want.

Disc List

Off

Folder List

Off

15: 45

MP3 DISC

DISC 02 DISC 03 DISC 04 DISC 05 DISC 06

My Best

Cinema Pops My Best2 Favorite Song Cinema2

ENT

• Each time you hold the button, you can display the other list of the remaining discs.

! Select a disc to start playing.

Disc List

MP3 DISC DISC 02 DISC 03

DISC 04

DISC 05 DISC 06

Off

ENT

File List

Off

Song011.mp3 Song012.mp3 Song013.mp3

Song014.mp3

Song015.mp3 Song016.mp3

ENT

Selecting playback modes

You can use only one of the following playback modes—Intro/Repeat/Random. Ex. To select Track Repeat

AV Menu

Mode

Off

All Off Intro

Repeat

Random

ENGLISH

Setup

Mode menu icon

AV Menu

Mode

ENT

Enter

ENT

Enter

Repeat

Off

Track

Disc

ENT

Set

When one of the playback modes is selected, the corresponding indicator lights up on the monitor.

To cancel, select <All Off> in step 3 or <Off> in step 4.

Disc type Intro Repeat Random

Track: Plays the first 15

seconds of each track

Disc: Plays the first 15 seconds

of the first track of all

Track: Repeats current track Disc: Repeats all tracks of the

current disc

Disc: Randomly plays all tracks

of the current disc

All: Randomly plays all tracks

of all loaded discs

loaded discs

Track: Plays the first 15

seconds of each track

Folder: Plays the first 15

seconds of the first track of each folder

Disc: Plays the first 15 seconds

of the first track of all

Track: Repeats current track Folder: Repeats all tracks of

the current folder

Disc: Repeats all tracks of the

current disc

Folder: Randomly plays all

tracks of current folder, then tracks of next folders

Disc: Randomly plays all tracks

of the current disc

All: Randomly plays all tracks

of all loaded discs

loaded discs

To use <Mode> menu

To use <List> menu

☞ above.

☞ page 40.

Disc List = Folder List = File List

You can use the following buttons on the remote controller to operate the CD changer.

or : Select disc.

Press: Select folder (MP3 only).

Press: Select track Hold: Reverse/forward search

EXTERNAL DEVICES

Listening to the DAB tuner

POWER]ON

ENGLISH

Band

Preset No.

TEXT indicator

DAB

DAB1 Preset1

Bayern Bayern2

FLATTEXT

News

☞ page 48

4 ¢

5 ∞

Select “DAB.”

~ Ÿ Select the bands.

Service label /Frequency, channel

AFDRC ANN

DAB indicators/Standby Reception indicators

* Information changes when you press DISP. While tuning in a

service with DLS (Dynamic Label Segment), the TEXT indicator lights up.

15: 45

PTY code

Ensemble label*

! Searching for an ensemble.

• Manual Search: Hold either 4 or ¢ until “Manual Search” appears on the display, then press it repeatedly.

⁄ Select a service (either primary or secondary) to listen to.

When surrounding sounds are noisy

Some services provide Dynamic Range Control (DRC) signals together with their regular programme signals. DRC will reinforce the low level sounds to improve your listening.

• The DRC indicator will light up while tuning in a service with the DRC signals.

AV Menu

Setup

ENT

Enter

AV Menu

Mode

Mode menu icon

Mode

D. Range Control

Announce Standby Pty Standby

Off

D. Range Control

Off DRC1

DRC2

DRC3

ENT

Enter

Exit

• As the number increases, the effect becomes stronger.

Manual presetting

You can preset six DAB services (primary) for each band.

On the unit:

Search for a service you want to preset.

DAB1

Service Label

No Serv.

FFH

No Serv.

HRS

HRH

Store

• Preset List can also be accessed through <AV

Menu> = <List> (☞ right).

4 Select a preset number.

DAB1 Store

Service Label

No Serv.

FFH

No Serv.

HRS

HRH

DAB

DAB1 Preset4

Bayern Bayern2

FLAT

AF ANNDRC

15: 45

Selecting preset stations

On the remote:

DAB1 Store

Service Label

No Serv.

FFH

Bayern2

HRS

HRH

ENT

Select a preset service.

ENT

• Preset List can also be accessed through <AV

DAB1 Store

Service Label

No Serv.

FFH

Bayern2

HRS

HRH

ENT

ENGLISH

Menu> = <List>.

ENT

AV Menu

Setup

AV Menu

List

List menu icon

ENT

Enter

ENT

Enter

Activating/deactivating TA/PTY Standby Reception

• Operations are exactly the same as explained on page 13 for FM RDS stations.

• You cannot store PTY codes separately for the DAB tuner and for the FM tuner.

EXTERNAL DEVICES

Activating/deactivating Announcement Standby Reception

Announcement Standby Reception allows the

ENGLISH

unit to switch temporarily to your favorite service (announcement type).

Announcement Standby Reception Indicator

Activate <AV Menu>, then select <Mode>, <Announce Standby> (☞ below).

The unit will temporarily switch to your favorite service from any source other than FM/AM.

Not yet activated. Tune in to another service providing the related signals.

To deactivate, select <Off> in step 4, then press ENT once (☞ right).

Activating Announcement Standby Reception

Mode menu icon

AV Menu

Setup

AV Menu

Mode

Off

ENT

D. Range Control

Announce Standby

Pty Standby

Enter

ENT

Enter

ANN

Lights up

Flashes

Goes off

Announce Standby

Off

Transport News

Announce Standby

Transport News

Warning News Weather Event

ENT

Exit

6 Select an announcement type for

Announcement Standby Reception.

Announce Standby

Transport News Warning News

Weather

Event

ENT

Exit

Tracing the same programme— Alternative Frequency Reception (DAB AF)

• While receiving a DAB service: When driving in an area where a service cannot be

received, this unit automatically tunes in to another ensemble or FM RDS station, broadcasting the same programme.

• While receiving an FM RDS station: When driving in an area where a DAB service is

broadcasting the same programme as the FM RDS station, this unit automatically tunes in to the DAB service.

When shipped from the factory, Alternative Frequency Reception is activated.

To deactivate the Alternative Frequency Reception, ☞ pages 50 and 54.

Available announcement types:

Transport News, Warning, News, Weather, Event, Special Event, Radio Info, Sports News, Financial News.

Listening to the iPod/D. player

POWER]ON

4 ¢ :

Press: Select track Hold: Reverse/forward search

5 ∞ 5 : Enter player’s menu ∞ : Pause/stop playback

• To resume, press again.

It is required to connect the interface adapter (KSPD100 for Apple iPod or KS-PD500 for JVC D. player) to the CD changer jack on the rear.

Preparation:

Make sure <iPod> or <D. Player> is selected for the external input setting. (☞ page 55)

~ Select “iPod” or “D. PLAYER.”

Playback starts automatically.

Ÿ Select a track.

Selecting a track from the player’s menu

1 Enter the player’s menu.

• This mode will be canceled if no operations are done for about 5 seconds.

2 Select the desired item.

Press: Select an item Hold: Skip 10 items at a time

For iPod: Playlists Ô Artists Ô Albums Ô Songs

Ô Genres Ô Composers Ô (back to the beginning)

For D. player: Playlist Ô Artist Ô Album Ô Genre Ô Track Ô (back to the beginning)

Track no./Playing time

D.PLAYER

01 0:45:38 Album Name Artist Name Track Title

☞ page 48

FLAT

15: 45

3 Confirm the selection.

4 Repeat steps 2 and 3 to select a track.

• When a track is selected finally, playback starts.

• To return to the previous menu...

Selecting playback modes

1 Display <AV Menu>, then select <Mode>

menu icon.

2 Enter <Mode>, then select <Repeat> or

<Random>.

3 Select an appropriate option.

Repeat One: Functions the same as “Repeat

One” or “Repeat Mode = One.” All: Functions the same as “Repeat All” or “Repeat Mode = All.”

Random Album: Functions the same as

“Shuffle Albums” of the iPod. Song/On: Functions the same as “Shuffle Songs” or “Random Play = On.”

• When one of the playback modes is selected, the corresponding indicators light up on the monitor.

To cancel, select <All Off> in step 2 or <Off> in step 3.

• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

EXTERNAL DEVICES

ENGLISH

Listening to other external components

AV-INPUT

You can connect an external component to the LINE IN/VIDEO IN plugs.

ENGLISH

• You can also connect a Navigation System to the VIDEO IN plug so that you can watch the navigation screen (Make sure <Navigation> is selected for <AV Input>). (☞ page 55)

POWER]ON

Assigned title (

☞ page 49) ☞ page 48

AV-IN

AV-INPUT

Press if no playback picture appears, but source information (this) screen is displayed.

FLAT

15: 45

~ Select “AV-IN.” Ÿ Turn on the connected component and start playing the source.

• If you select <Camera Mirror> or <Navigation> for <AV Input> (☞ page 55), some status messages

such as volume level change will not appear on the monitor while viewing the picture.

When <Navigation> is selected for <AV Input>...

• You can use the source “AV-IN” for listening to an audio source connected to the LINE IN plugs.

• While selecting other source, you can watch the navigation screen without changing the source. To watch the navigation screen, press DISP repeatedly.

EXT-INPUT

You can connect an external component to the CD changer jack on the rear using the Line Input Adapter—KS-U57 (not supplied) or AUX Input Adapter—KS-U58 (not supplied).

POWER]ON

Assigned title (☞ page 49) ☞ page 48

ENGLISH

EXT-IN

EXT-INPUT

Preparation: Make sure <External Input> is selected for the external input setting. (☞ page 55)

FLAT

15: 45

~ Select “EXT-IN.” Ÿ Turn on the connected component and start playing the source.

EXTERNAL DEVICES

Sound equalization

ENGLISH

POWER]ON

Selecting sound mode

AV Menu

Setup

Equalizer menu icon

AV Menu

Equalizer

! Select a sound mode.

Equalizer

Flat Hard Rock

R&B

Pop Jazz

Edit

+03

ENT

60.0 Hz

Store

Storing your own adjustment

You can store your adjustment into User1, User2, and User3.

1 Repeat steps ~ and Ÿ, then in step !...

ENT

Enter

ENT

Enter

Equalizer

Edit

Flat Hard Rock

R&B

Pop Jazz

60.0 Hz

ENT

Exit

+03

ENT

Store

2 Adjust.

ENT

Exit

• For preset equalizing values of each sound mode,

☞ page 64.

• For multi-channel source, the sound mode is

temporarily canceled.

3 Store.

User Store

User1 User2

User3

ENT

Store

Assigning titles to the sources

POWER]ON

Title Entry

Press: Change character set Hold: Erase title

ENGLISH

AV-In Name

MY BEST

You can assign titles to “AV-IN” and “EXT-IN.” Ex.: Assigning title to “AV-IN”

~ Select “AV-IN.” Ÿ Display the title entry screen.

AV Menu

ENT

Setup

AV Menu

Mode

Mode menu icon

Mode

Title Entry

Enter

ENT

Enter

DISP

A a 0 Á á

! Assign a title.

1 Select a character, then move the entering

2 Repeat step 1 until you finish entering the

⁄ Finish the procedure.

ENT

Store

position.

• To change the character set, press DISP.

(For available characters, ☞ page 65.)

title.

• The maximum number of characters is 16.

Title Entry

DISP

A a 0 Á á

AV-In Name

AV-INPUT

ENT

Store

SETTINGS

Menu operations

POWER]ON

ENGLISH

Ex. Changing the <High Pass Filter> setting

AV Menu

Setup

ENT

Non-available items will be displayed being shaded.

Sound menu icon

AV Menu

Sound

ENT

Enter

Setup Equalizer Sound

AV Menu

Setup

Mode List Bluetooth

Sound

Through

• For some items, repeat this steps to set the sub-items.

⁄

High Pass Filter

ENT

Enter

Fader/Balance Volume Adjust Subwoofer

High Pass Filter

Crossover

Through

Disc Surround

Dual Zone

ENT

Exit

Menu items

AV Menu

Setup

• The display indications may change according to change of the specifications.

Setup

Equalizer

Sound

Disc Surround

ENT

Enter

Mode

List

Bluetooth

Dual Zone

Display

Clock

Disc Setup 1

Disc Setup 2

Tuner

Input

Others

Setup

Menu items Selectable settings, [reference page]

Initial: Underlined

Demonstration Off : Cancels.

On : Activates the demonstration on the monitor.

Wall Paper You can select the background picture of the monitor.

Future-Blue

Future-Green, Wave-Blue, Wave-Green, Wave-Pink, Metal-A, Metal-B, Ball-A, Ball-B, Ball-C, Dolphin, Simple-Red, Simple-Purple, Simple-Blue, Simple-Gray

Scroll Off : Cancels.

Once : Scrolls the disc information once. Auto : Repeats scrolling (5-second intervals).

• Holding DISP (on the unit) scrolls the information regardless of this

setting.

Tag Display Off : Cancels.

On : Shows the Tag data while playing MP3/WMA/WAV/AAC tracks.

Dimmer Off : Cancels.

Display

On : Activates dimmer. Auto : Dims the monitor when you turn on the headlights.* Time Set : Press ENT (or ¢) to display the time setting screen, then

set the Dimmer On/Off times.

Bright You can adjust brightness of the monitor.

–15 (darkest) to +15 (brightest); Initial 00

Picture Adjust*

You can adjust the following to make the monitor clear and legible for watching the playback picture. The setting will be stored for “DISC/USB,” and “AV-IN.”

–15 to +15; Initial 0 Bright : Adjust if the picture is too bright or too dark. Contrast : Adjust the contrast. Color : Adjust the color of the picture—lighter or darker. Tint : Adjust the tint if the human skin color is unnatural.

The ILLUMINATION CONTROL lead connection is required. (☞ Installation/Connection Manual)

Adjustable only when the source is a disc or USB containing pictures or movies, or “AV-IN.”

ENGLISH

Continued on the next page

SETTINGS

Menu items Selectable settings, [reference page]

Aspect*

You can change the aspect ratio of the picture.

Aspect ratio of incoming signal

ENGLISH

4:3 16:9

Full :

For 16:9 original pictures

Auto : • For “DISC”: Aspect ratio is automatically

Display

selected to match to the incoming signals.

• For the other video sources: Aspect ratio is fixed to <Regular>.

Regular :

For 4:3 original pictures

Language*

Select the indication language shown on the monitor.

English, Spanish, French, German, Italian, Dutch, Swedish, Danish, Russian

Time Set

12Hours/24Hours

Clock

OSD Clock

Clock Adjust

Menu Language

Audio Language

Initial 0:00, ☞ [6]

12 Hours, 24 Hours, ☞ [6]

Off, On, ☞ [6]

Off, Auto, ☞ [6]

Select the initial disc menu language; Initial English (☞ also page 65).

Select the initial audio language; Initial English (☞ also page 65).

Subtitle Select the initial subtitle language or erase the subtitle (<Off>);Initial

English (☞ also page 65).

Disc Setup 1*

OSD Language Select the on-screen language used for the external monitor connected

to the VIDEO OUT plug; Initial English.

Not adjustable for audio sources.

After you change the indication language setting, turn off then on the power so that your setting takes effect.

*5 Selectable only for “DISC” and “USB.” (Playback stops when you select one of the items.)

Menu items Selectable settings, [reference page]

Monitor Type Select the monitor type to watch a wide screen picture on the external

16:9 4:3 Letterbox

monitor.

16:9 : Select when the aspect ratio of the external monitor is 16:9. 4:3 Letterbox/4:3 Pan Scan : Select when the aspect ratio of the

4:3 Pan Scan

external monitor is 4:3. Refer to the illustrations on the left to see how the pictures are shown on the monitor.

ENGLISH

OSD Position

Position 1 Position 2

Select the position of the on-screen bar, ☞ [27].

1 : Higher position 2 : Lower position

File Type Select playback file type when a disc/USB contains different types of

Disc Setup 1*

files. You can store this setting separately for each source —“DISC/ USB.”

Audio : Plays back audio files. Still Picture : Plays back JPEG files. Video : Plays back DivX/MPEG1/MPEG2 files.

DivX Regist. (Registration) This unit has its own Registration Code. Once you have played back a

file with which the Registration Code recorded, this unit’s Registration Code is overwritten for copyright protection.

D. (Dynamic) Range Compres. (Compression)*

You can enjoy a powerful sound at a low volume level while playing Dolby Digital software.

Auto : Select to apply the effect to multi-channel encoded software. On : Select to always use this function.

Speaker Size*

You can adjust the speaker size setting.

• Front SPK : Small, Large

Select the speaker

Disc Setup 2

Adjust the speaker size

• Center SPK : None, Small, Large

• Rear SPK : None, Small, Large

• Subwoofer : On, Off

• Speaker size : <Large> for 13 cm diameter or more; <Small> for 13 cm or less.

• Front speakers and rear speakers cannot be adjusted separately the left and right.

Regardless of the setting above...

• No sound comes out of the subwoofer while playing Dolby Pro Logic II Movie or Music if the front speaker is set to <Large>.

• No sound comes out of the center speaker when surround is deactivated.

Selectable only for “DISC” and “USB.” (Playback stops when you select one of the items.)

Continued on the next page

SETTINGS

Menu items Selectable settings, [reference page]

Speaker Level You can adjust the output level of the activated speakers

(☞ <Speaker Size> on page 53), monitoring the test tone. Front Lch/Center Ch/Front Rch/Rear Rch/Subwoofer*6/Rear Lch

: adjust the output level of each speaker in the range of –10dB to

ENGLISH

Select the speaker

+10dB; Initial 0dB.

Adjust the speaker level

• Press and hold ENT to turn on and off the test tone.

Speaker Distance*

Disc Setup 2

Select the speaker

You can adjust the speaker output timing. Front Lch/Center Ch/Front Rch/Rear Rch/Rear Lch : adjust the

speaker distance from the listening position in the range of 15cm/6 inches to 600 cm/240 inches in 15 cm/6 inch step; Initial 120 cm/48 inch (for center speaker), 150 cm/60 inch (for

Adjust the speaker

other speakers).

distance

• Press and hold DISP to change the measuring unit—cm and inch.

AF Regional When the received signals from the current station become weak...

Off : Cancels—not selectable when <DAB AF> is set to <On>. AF Regional : Switches to another station broadcasting the same

programme. The REG indicator lights up.

AF : Switches to another station. The programme may differ from the

one currently received (AF indicator lights up), ☞ [14].

TA Volume

Tuner

Program Search

00 to 30 or 50*

Off, On, ☞ [14]

, Initial 15, ☞ [13].

IF Band Width Auto : Increases the tuner selectivity to reduce interference noises

between adjacent stations. (Stereo effect may be lost.)

Wide : Subject to the interference from adjacent stations, but sound

quality will not be degraded and the stereo effect will remain.

DAB AF*

This subwoofer level setting takes effect only when surround is activated. (☞ also page 24, 25)

Off, On, ☞ [44]

*7 This setting does not take effect for MPEG1/MPEG2 and DivX with MP3 audio track. *8 Depends on the amplifier gain control. (☞ page 56) *9 Appears only when DAB tuner is connected.

Menu items Selectable settings, [reference page]

AV Input You can determine the use of LINE IN and VIDEO IN plugs.

Off : Select when no component is connected (“AV-IN” is skipped while

selecting the source).

Audio&Video : Select when connecting an AV component such as a

VCR.

Audio : Select when connecting an audio component such as a digital

audio player.

Camera*10: Select when connecting the rear view camera. Camera Mirror*

: The mirror image of the rear view is displayed on

the monitor. (The monitor on the unit only; the normal rear view

Input

appears on the external monitor.)

Navigation : Select when connecting a Navigation System. ☞ [46]

External Input*

For connecting an external component to the CD changer jack on the rear.

Changer/iPod/D. Player*12: CD changer, iPod, or D. player

☞ [40, 45]

External Input : Any other than the above. ☞ [47]

• For connecting the DAB tuner, this setting is not required. It is automatically detected.

Beep Off : Cancels.

On : Activates the key-touch tone.

Telephone Muting*

Off : Cancels. Muting1, Muting2 : Select either one which mutes the sounds while

Others

using the cellular phone.

ENGLISH

Initialize Initialize all settings you have made in <AV Menu>. Press ENT, then

reset the unit. (☞ page 3)

Reverse lamp lead connection is required. See Installation/Connection Manual (separate volume). The rear view

through the camera appears on the monitor in “Full” aspect ratio (regardless of the aspect ratio setting) when you shift the gear to the reverse (R) position.

Not selectable when the component connected to the CD changer jack is selected as the source.

The name of the component detected through the CD changer jack is shown.

*13 The TEL MUTING lead connection is required. See Installation/Connection Manual (separate volume).

SETTINGS

Equalizer

Flat/Hard Rock/R&B/Pop/Jazz/Dance/Country/Reggae/Classic/User1/User2/User3, ☞ [48]

Sound

ENGLISH

Menu items Selectable settings, [reference page]

Fader/Balance Adjust fader—speaker output balance between the front and rear speakers.

Adjusts fader

Adjust balance

Volume Adjust Adjust and store auto-adjustment volume level for each source, comparing to

Subwoofer*

High Pass Filter Through : Select when the subwoofer is not connected.

Crossover Adjust the crossover frequency between the front/rear speakers and the

Amplifier Gain You can change the maximum volume level of this unit.

Rear Speaker*

This subwoofer level setting takes effect only when surround is deactivated. (☞ also page 24, 25)

This setting takes effect only when Dual Zone is activated. (☞ also page 28)

• Upmost—front only

• Downmost—rear only When using a two-speaker system, set the fader to the center (00). Adjust balance—speaker output balance between the left and right speakers.

• Leftmost—left only

• Rightmost—right only

the FM volume level. The volume level will automatically increase or decrease when you change the source. –12 to +12; Initial 00

Adjust the settings below in the submenu: Phase : Subwoofer phase. Select either <Normal> or <Reverse>, which

reproduces a better sound.

Level : Subwoofer output level. Level: –06 to +08; Initial 00

On : Select when the subwoofer is connected.

subwoofer.

80Hz, 120Hz, 150Hz

Off : Deactivates the built-in amplifier. Low Power : VOL 00 to 30 (Select this if the maximum power of the speakers

is less than 50 W.)

High Power : VOL 00 to 50

You can activate/deactivate the rear speakers. Off, On

Disc Surround*

Menu items Selectable settings, [reference page]

Surround Off Select to deactivate the surround function.

Surround On

Select to activate the surround function. ☞ [24] Auto, Through, Dolby PLII Movie, Dolby PLII Music

• When you select Dolby PLII Music, you can adjust <Panorama> and <Center Width>.*

*16 Selectable only for “DISC” and “USB.”

This setting takes effect only when the center speaker is activated.

Mode*

Menu items Selectable settings, [reference page]

ENGLISH

Mono

DX/Local

SSM

PTy Standby

Only for FM. (Off, On), ☞ [10]

Only for FM. (DX, Local), ☞ [11]

Only for FM. ☞ [11]

Only for FM/DAB. (Off, News), ☞ [13, 43]

• When you activate PTY Standby Reception, you can change the PTY code for PTY Standby Reception.

Title Entry

Only for AV-IN and EXT-IN. ☞ [49]

All Off/Intro/Repeat/Random Only for disc/USB playback and iPod/D. player.

☞ [19, 32, 41, 45]

(Dynamic)

Range Control

Announce Standby

Items listed under <Mode> vary among the playback sources.

Only for DAB. (Off, DRC1, DRC2, DRC3), ☞ [42]

Only for DAB. (Off, Transport News), ☞ [44]

List

The accessible lists differ depending on the sources. ☞ [12, 20, 39, 41]

SETTINGS

Bluetooth*

Menu items Selectable settings, [reference page]

Dial Menu Only for the device connected for “Bluetooth Phone.”

Select the method to make a call. ☞ [37]

ENGLISH

Message Only for the device connected for “Bluetooth Phone.”*

You can read a message from the following message histories.

Unread : Messages you have not read. Read : Messages you have read. Unsent : Messages you have not sent. Sent : Messages you have sent.

• The number of messages in each history is also shown on the monitor.

Open

☞ [34]

Special Device Only for “NEW DEVICE.”

Shows the list of Bluetooth devices which require some special procedure to establish Bluetooth connection. Select a device you want to connect.

• After selecting the device, use <Open> or <Search> (☞ page 34) for

connection.

• Once the connection is established, it is registered in the unit. You can

connect the unit and the device by using <Connect> (☞below) from the next time.

Connect Only for the registered devices.

After selecting a device from among the registered devices (☞ page 35, 39), establish the connection with it.

Disconnect Only for the device being connected.

Disconnect the current device before connecting another device.

Delete Pair Only for the registered devices.

Delete the registered devices.

Selectable only for “ Bluetooth Phone” or “Bluetooth Audio. ” Select a device (or “NEW DEVICE”) before operating the

menu.

*20 Selectable only when the device is compatible with SMS.

When operating the Bluetooth device, refer also to the instructions supplied with the device.

Menu items Selectable settings, [reference page]

Auto Connect*

When the unit is turned on, the connection is established automatically with...

Off : No Bluetoothdevice. Last : The last connected Bluetooth device. Order : The available registered Bluetooth device found at first.

Auto Answer*

Off : The unit does not answer the calls automatically. Answer the calls

manually.

On : The unit answers the incoming calls automatically. Reject : The unit rejects all incoming calls.

Settings

Message Info*

Auto : The unit informs you of the arrival of a message by ringing and

displaying “Receiving Message.” To read the message, press ENT (☞ page 37).

Manual : The unit does not inform you the arrival of a message.

MIC Setting*

Adjust microphone volume connected to the unit.

01, 02, 03

Version*

Selectable only for “Bluetooth Phone.”

* *22 Only for the device connected for “Bluetooth Phone.” Not selectable for “NEW DEVICE”.

If you wish to receive more information about Bluetooth, visit our JVC web site.

The Bluetooth software and hardware versions are shown.

Dual Zone

Off, On, On/Surround On, ☞ [28]

ENGLISH

SETTINGS

Maintenance

How to clean the connector

Frequent detachment will deteriorate the connectors.

ENGLISH

To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

Connector

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

How to handle discs

When removing a disc from its case, press down the center holder

of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

Center holder

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this unit may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Do not use the following discs:

Warped disc

Sticker

Sticker residue

Stick-on label

More about this unit

General

Turning on the power

• By pressing SRC (source) on the unit, you can also turn on the power. If the source is ready, playback starts.

FM/AM

Storing stations in memory

• When SSM is over, received stations are preset in

No. 1 (lowest frequency) to No. 6 (highest frequency).

Disc

General

• In this manual, words “track” and “file” are interchangeably used.

• This unit can also play back 8 cm discs.

• This unit can only play back audio CD (CD-DA) files if different type of audio files (MP3/WMA/WAV/AAC) are recorded in the same disc.

• This unit can display only one-byte characters. No other characters can be correctly displayed.

Inserting a disc

• When a disc is inserted upside down or has no playable files, “Cannot play this disc Check the disc” appears on the monitor. Eject the disc.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc playback starts.)

Changing the source

• If you change the source, playback also stops without ejecting the disc.

Next time you select “DISC” for the playback source,

disc play starts from where it stopped previously.

Playing Recordable/Rewritable discs

• This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder).

• Use only “finalized” discs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• This unit can recognize a total 25 characters for file/ folder names.

• Some discs or files may not be played back due to their characteristics or recording conditions.

Playing DVD Audio

• Some DVD Audios prohibit downmix. When you play back such a disc, “LR ONLY” appears on the display and the unit plays back the left front and right front signals.

• “MULTI CH” appears on the monitor after a beep when you try to play a multi-channel disc with Surround turned <Off>.

Playing DVD-VR

• This unit cannot play back CPRM (Content Protection for Recordable Media) protected files.

• For details about DVD-VR format and play list, refer to the instructions supplied with the recording equipment.

File playback

Playing DivX files

• This unit can play back DivX files with the extension code <.divx>, <.div>, <.avi> (regardless of the letter case—upper/lower).

• This unit supports the DivX files whose resolution is 720 x 576 pixels or less.

• This unit supports DivX 6.x, 5.x, 4.x, and 3.11.

• Audio stream should conform to MP3 or Dolby Digital.

• The file encoded in the interlaced scanning mode may not be played back correctly.

• The maximum bit rate for video signals (average) is as follows: – DVD: 4 Mbps – USB: 2 Mbps

REFERENCES

ENGLISH

Playing MPEG1/MPEG2 files

• This unit can play back MPEG1/MPEG2 files with the extension code <.mpg>, <.mpeg>, or <.mod>*. * <.mod> is an extension code used for the

MPEG2 files recorded by JVC Everio camcorders.

ENGLISH

• The stream format should conform to MPEG system/ program stream.

• The file format should be MP@ML (Main Profile at Main Level)/SP@ML (Simple Profile at Main Level)/ MP@LL (Main Profile at Low Level).

• Audio streams should conform to MPEG1 Audio Layer-2 or Dolby Digital.

• The maximum bit rate for video signals (average) is as follows: – DVD: 4 Mbps – USB: 2 Mbps

Playing JPEG files

• This unit can play back JPEG files with the extension code <.jpg>, or <.jpeg>.

• It is recommended that you record a file at 640 x 480 resolution.

• This unit can play back baseline JPEG files. Progressive JPEG files or lossless JPEG files cannot be played.

Playing MP3/WMA/WAV/AAC files

• This unit can play back files with the extension code <.mp3>, <.wma>, <.wav>, or <.m4a> (regardless of the letter case—upper/lower).

• This unit can play back the files meeting the conditions below: – Bit rate: MP3/WMA: 32 kbps — 320 kbps AAC: 16 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG2) 48 kHz, 44.1 kHz, 32 kHz, 22.05 kHz (for WMA)

44.1 kHz (for WAV) 48 kHz, 44.1 kHz (for AAC)

• This unit can show ID3 Tag Version

1.0/1.1/2.2/2.3/2.4 (for MP3). This unit can also show WAV/WMA/AAC Tag.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in elapsed

time indication.

• This unit cannot play back the following files: – MP3 files encoded with MP3i and MP3 PRO

format. – MP3 files encoded with Layer 1/2. – WMA files encoded with lossless, professional,

and voice format. – WMA files which are not based upon Windows

Media® Audio. – WMA/AAC files copy-protected with DRM. – AAC files purchased from the iTunes store. – Files which have the data such as AIFF, ATRAC3,

etc.

Enjoying surround sounds

• If <Surround On> is selected, “MULTI” surround playback automatically starts for multi-channel encoded discs regardless of the <Surround On> setting.

• You cannot activate surround for MPEG multi-channel DVD Video, DivX 2-channel and MPEG 2-channel sources. If <Surround On> is selected, stereo sounds are emitted only through the front speakers. “FRONT 2CH” appears on the source information screen.

• When “FIX” appears on the source information screen, no sound comes out of the subwoofer.

• When <AUTO> is selected, downsampling is performed for DVD Video (LPCM only), DVD-VR (LPCM only), and DVD Audio with fs=88.2 kHz/96 kHz and higher.

USB

• If “No USB device“ appears after removing a device, Reattach a device or select another playback source.

• When the USB device has no playable files, or has not been formatted correctly, “Cannot play this device Check the device” appears on the monitor.

• The unit cannot recognize a USB device whose rating is other than 5 V and does not exceed 500 mA.

• While playing from a USB device, the playback order may differ from other players.

• This unit may be unable to play back some USB devices or some files due to their characteristics or recording conditions.

• Depending on the shape of the USB devices and connection ports, some USB devices may not be attached properly or the connection might be loose.

• When connecting a USB device, refer also to its instructions.

• Connect only one USB device to the unit at a time. Do not use a USB hub.

• This unit may not recognize a USB device connected through a USB card reader.

• This unit may not play back files in a USB device properly when using a USB extension cord.

• This unit cannot assure proper functions or supply power to all types of the devices.

• This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder).

• This unit can recognize a total 25 characters for file/ folder names.

Warning messages for Bluetooth operations

• Connection Error : The device is registered but the connection has failed. Use <Connect> to connect the device again. (☞ page 35)

• Error : Try the operation again. If “Error” appears again, check if the device supports the function you have tried.

• Device Unfound : No available Bluetooth device is detected by <Search>.

• Loading : The unit is updating the phone book and/ or SMS.

• Please Wait... : The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again (or reset the unit).

Icons for phone types

• These icons indicate the phone type set on the device.

: Cellular phone

: Household phone

: Office

: General

: Other than above

DAB tuner

• Only the primary DAB service can be preset even when you store a secondary service.

ENGLISH

Bluetooth operations

General

• While driving, do not perform complicated operation such as dialling the numbers, using phone book, etc. When you perform these operations, stop your car in a safe place.

• Some Bluetooth devices may not be connected to this unit depending on the Bluetooth version of the device.

• This unit may not work for some Bluetooth devices.

• Connecting condition may vary depending on circumstances around you.

• When the unit is turned off, the device is disconnected.

iPod/D. player operations

• When you turn on this unit, the iPod or D. player is charged through the adapter connected to this unit.

• The text information may not be displayed correctly. This unit can display up to 40 characters.

Continued on the next page

REFERENCES

Notice:

When operating an iPod or a D. player, some operations may not be performed correctly or as intended. In this case, visit the following JVC web site:

ENGLISH

For iPod users: <http://www.jvc.co.jp/english/car/ support/ks-pd100/index.html> For D. player users: <http://www.jvc.co.jp/ english/car/support/ks-pd500/index.html>

Menu settings

• If you change the <Amplifier Gain> setting from <High Power> to <Low Power> while the volume level is set higher than “30,” the unit automatically changes the volume level to “VOL 30.”

• After you change any of <Menu Language/Audio Language/Subtitle> settings, turn off then on the power, and re-insert the disc (or insert another disc) so that your setting takes effect.

• When you select <16:9> for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width.

• Even if <4:3 Pan Scan> is selected, the screen size may become <4:3 Letterbox> for some discs.

About sounds reproduced through the rear terminals

• Speaker out/analog discrete output—LINE OUT (FRONT/REAR)/CENTER OUT/SUBWOOFER: Multi-channel signals are emitted for a multichannel encoded software. (When Dual Zone is activated, the same signal emitted through 2nd AUDIO OUT plugs are emitted for the main source “DISC.”)

• 2nd AUDIO OUT: 2-channel signal is emitted when Dual Zone is activated. When playing a multi-channel encoded disc, multi-channel signals are downmixed (except for some DVD Audio).

• “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries.

• DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, inc. and are used under license.

• Official DivX® Ultra Certified product

• Plays all versions of DivX® video (including DivX® 6) with enhanced playback of DivX® media files and the DivX® Media Format

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• iPod and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

Preset equalizing values

Frequency Sound mode Flat 00 00 00 00 00 00 00 Hard Rock +03 +03 +01 00 00 +02 +01 R&B +03 +02 +02 00 +01 +01 +03 Pop 00 +02 00 00 +01 +01 +02 Jazz +03 +02 +01 +01 +01 +03 +02 Dance +04 +02 00 –02 –01 +01 +01 Country +02 +01 00 00 00 +01 +02 Reggae +03 00 00 +01 +02 +02 +03 Classic +02 +03 +01 00 00 +02 00 User1/2/3 00 00 00 00 00 00 00

60 Hz 150 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 15 kHz

Language codes (for DVD/DivX language selection)

Code Language Code Language Code Language Code Language Code Language

AA Afar FA Persian KL Greenlandic OC Occitan ST Sesotho AB Abkhazian FI Finnish KM Cambodian OM (Afan) Oromo SU Sundanese AF Afrikaans FJ Fiji KN Kannada OR Oriya SW Swahili AM Ameharic FO Faroese KO Korean (KOR) PA Panjabi TA Tamil AR Arabic FY Frisian KS Kashmiri PL Polish TE Telugu AS Assamese GA Irish KU Kurdish PS Pashto, Pushto TG Tajik AY Aymara GD Scots Gaelic KY Kirghiz PT Portuguese TH Thai AZ Azerbaijani GL Galician LA Latin QU Quechua TI Tigrinya BA Bashkir GN Guarani LN Lingala RM Rhaeto-Romance TK Turkmen BE Byelorussian GU Gujarati LO Laothian RN Kirundi TL Tagalog BG Bulgarian HA Hausa LT Lithuanian RO Rumanian TN Setswana BH Bihari HI Hindi LV Latvian, Lettish RW Kinyarwanda TO Tonga BI Bislama HR Croatian MG Malagasy SA Sanskrit TR Turkish BN Bengali, Bangla HU Hungarian MI Maori SD Sindhi TS Tsonga BO Tibetan HY Armenian MK Macedonian SG Sangho TT Tatar BR Breton IA Interlingua ML Malayalam SH Serbo-Croatian TW Twi CA Catalan IE Interlingue MN Mongolian SI Singhalese UK Ukrainian CO Corsican IK Inupiak MO Moldavian SK Slovak UR Urdu CS Czech IN Indonesian MR Marathi SL Slovenian UZ Uzbek CY Welsh IS Icelandic MS Malay (MAY) SM Samoan VI Vietnamese DZ Bhutani IW Hebrew MT Maltese SN Shona VO Volapuk EL Greek JI Yiddish MY Burmese SO Somali WO Wolof EO Esperanto JW Javanese NA Nauru SQ Albanian XH Xhosa ET Estonian KA Georgian NE Nepali SR Serbian YO Yoruba EU Basque KK Kazakh NO Norwegian SS Siswati ZU Zulu

ENGLISH

Characters shown on the monitor

In addition to the roman alphabet (A – Z, a – z), the following characters will be used to show the various information on the monitor.

• You can also use the following

characters to assign titles. (☞ page 49)

Upper and lower cases

Numbers and symbols

REFERENCES

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

ENGLISH

• No sound comes out of the center speaker.

• The monitor is not clear and legible. Sunshine from the windscreen may cause this symptom.

• The unit does not work at all.

• The remote controller does not work.

General

• “No Signal” appears. • Change the source.

• “Mecha Error Push Reset” appears on the monitor, and the panel does not move.

• SSM automatic presetting does not work.

• Static noise while listening to the radio. Connect the aerial firmly.

FM/AM

• Disc can be neither recognized nor played .

• Disc cannot be ejected.

• Recordable/Rewritable discs cannot be played back.

• Tracks on the Recordable/Rewritable discs cannot be skipped.

• Playback does not start. • Insert the disc correctly again.

Disc playback

• The playback picture is not clear and legible.

• Sound and pictures are sometimes interrupted or distorted.

Symptoms Remedies/Causes

• Center speaker is not activated. (☞ page 53) Once you have reset the unit, make sure to activate the

speaker again.

• Center speaker is used only for surround playback. No sound comes out for stereo playback.

Adjust <Bright>. (☞ page 51)

Reset the unit. (☞ page 3)

Deactivate Dual Zone. (☞ page 28) (While Dual Zone is activated, the remote controller only functions for operating the DVD/CD player.)

• Start the playback on the external component connected to VIDEO IN plug.

• Check the cords and connections.

• Signal input is too weak.

Reset the unit. (☞ page 3)

Store stations manually. (☞ page 11)

Eject the disc forcibly. (☞ page 3)

Unlock the disc. (☞ page 20)

• Insert a finalized disc.

• Finalize the discs with the component which you used for recording.

• Region code of the DVD is not correct. (☞ page 4)

• The format of files is not supported by the unit.

Adjust items in <Picture Adjust>. (☞ page 51)

• Stop playback while driving on rough roads.

• Change the disc.

Symptoms Remedies/Causes

• No playback picture appears on the monitor. Parking brake lead is not connected properly.

(☞ Installation/Connection Manual)

• No picture appears on the external monitor. • Connect the video cord correctly.

• Select the correct input on the external monitor.

Disc playback

• “Eject Error” or “Loading Error” appears on the monitor.

• Disc cannot be played back. • Change the disc.

• Noise is generated. The track played back is not a playable file format. Skip to

• Tracks are not played back as you have intended them to play.

File playback

• Elapsed playing time is not correct. This sometimes occurs during playback. This is caused by

• “Not Support” appears on the monitor and track skips.

• Noise is generated. • The track played back is not a playable file format (MP3/

• Tracks cannot play back as you have intended them to play.

• “Now Reading” keeps flashing on the monitor.

USB playback

• Correct characters are not displayed (e.g. album name).

• While playing a track, sound is sometimes interrupted.

Changing the source by pressing SOURCE will solve this error.

• Record the tracks using a compliant application in the

appropriate discs. (☞ page 4)

• Add appropriate extension codes to the file names.

another file.

Playback order may differs from the one played back using other players.

how the tracks are recorded.

The track is unplayable.

WMA/WAV/AAC). Skip to another file.

• Do not add the extension code <.mp3>, <.wma>, <.wav>or <.m4a> to non-MP3/WMA/WAV/AAC tracks.

Playback order may differs from the one played back using other players.

• Readout time varies depending on the USB device.

• Do not use too many hierarchy, folders and empty folders.*

Folder that is physically empty or folder that contains

data but does not contain valid MP3/WMA/WAV/AAC track.

• Turn off the power then on again.

• Do not pull out or connect the USB device repeatedly while “Now Reading” is displayed on the monitor.

For available characters, ☞ page 65.

The tracks have not been properly copied into the USB device. Copy tracks again into the USB device, and try again.

ENGLISH

REFERENCES

Symptoms Remedies/Causes

• Bluetooth device does not detect the unit. This unit can be connected with one Bluetooth cellular phone and one Bluetooth audio device at a time. While connecting a device, this unit cannot be detected

ENGLISH

• The unit does not detect the Bluetooth

device.

• The unit does not make pairing with the

Bluetooth device.

• Echo or noise occurs. Adjust the microphone unit position.

• Phone sound quality is poor. • Reduce the distance between the unit and the Bluetooth

Bluetooth

• The sound is interrupted or skipped during playback of a Bluetooth audio device.

• “New Device” cannot be selected for “Bluetooth Audio.”

• The connected audio device cannot be controlled.

• “No Disc” appears on the monitor. Insert a disc into the magazine.

• “No Magazine” appears on the monitor. Insert the magazine.

• “Cannot play this disc Check the disc” appears on the monitor.

• “Reset 08” appears on the monitor. Connect this unit and the CD changer correctly and press

CD changer

• “Reset 01” – “Reset 07” appears on the monitor.

• The CD changer does not work at all.

from another device. Disconnect currently connected device and search again.

• Check the Bluetooth setting of the device.

• Search from the Bluetooth device. After the device detects the unit, select <Open> on the unit to connect the device. (☞ page 34)

• Enter the same PIN code for both the unit and target device. If the PIN code of the device is not indicated on its instructions, try “0000” or “1234.”

• Select the device name from <Special Device>, then try to connect again. (☞ page 35)

audio device.

• Move the car to place where you can get a better signal reception.

• Reduce the distance between the unit and the Bluetooth audio device.

• Disconnect the device connected for “Bluetooth phone.”

• Turn off, then turn on the unit.

• (When the sound is not yet restored,) connect the device again.

Bluetooth audio device is being connected. To select “New Device,” disconnect it. (☞ page 35)

Check whether the connected audio device supports AVRCP (Audio Video Remote Control Profile).

Disc does not include playable files. Replace the disc with playable files.

the reset button of the CD changer.

Press the reset button of the CD changer.

Reset the unit. (☞ page 3)

Symptoms Remedies/Causes

• “No DAB Signal” appears on the monitor. Move to an area with stronger signals.

• “Reset 08” appears on the monitor. Connect this unit and the DAB tuner correctly, then reset

the unit. (☞ page 3)

• The DAB tuner does not work at all. Connect this unit and the DAB tuner correctly, then reset

DAB tuner

• “Antenna Power NG” appears on the monitor. Check the cords and connections.

• The iPod/D. player does not turn on or does not work.

• The sound is distorted. Deactivate the equalizer either on this unit or the iPod/

• “Disconnect” appears on the monitor. Check the connecting cable and its connection.

• For iPod: Playback stops. The headphones are disconnected during playback. Restart

• No sound can be heard.

• “Error 01” appears on the monitor when connecting a D. player.

• “No Files” or “No Track” appears on the

iPod/D. player playback

monitor.

• “Reset 01” – “Reset 07” appears on the monitor.

• “Reset 08” appears on the monitor. Check the connection between the adapter and this unit.

• The iPod’s or D. player’s controls do not work after disconnecting from this unit.

• No picture appears on the monitor. • Turn on the video component if it is not on.

AV-IN

• The playback picture is not clear and legible.

the unit. (☞ page 3)

• Check the connecting cable and its connection.

• Charge the battery.

• For D. player: Update the firmware version.

D. player.

playback.

Disconnect the D. player from the adapter. Then, connect them again.

No tracks are stored. Import tracks to the iPod or D. player.

Disconnect the adapter from both this unit and iPod/ D. player. Then, connect them again.

Reset the iPod or D. player.

• This unit is not connected to the video component correctly. Connect it correctly.

Adjust items in <Picture Adjust>. (☞ page 51)

ENGLISH

REFERENCES

Specifications

Maximum Power Output: Front/Rear: 50 W per channel Continuous Power Output

(RMS):

ENGLISH

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Equalizer Control Range: Frequencies: 60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.5 kHz,

Signal-to-Noise Ratio: 70 dB Audio Output Level

LINE OUT (FRONT/

AMPLIFIER

REAR)/CENTER OUT/

SUBWOOFER: Color System: PAL Video Output (composite): 1 Vp-p/75 Ω Other Terminals: Input: LINE IN, VIDEO IN, MIC IN, USB input

Frequency Range: FM: 87.5 MHz to 108.0 MHz

FM Tuner: Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)

FM/AM TUNER

MW Tuner: Sensitivity/Selectivity: 20 μV/35 dB LW Tuner: Sensitivity: 50 μV

Signal Detection System: Non-contact optical pickup (semiconductor laser)

Frequency Response: DVD, fs=48 kHz: 16 Hz to 22 000 Hz

DVD/CD

Dynamic Range: 93 dB

Signal-to-Noise Ratio: 95 dB

Wow and Flutter: Less than measurable limit

Front/Rear: 20 W per channel into 4 Ω, 40 Hz to

20 000 Hz at no more than 0.8% total harmonic distortion

6.3 kHz, 15 kHz

Level: ±10 dB

Line-Out Level/Impedance: 5.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ

terminal, Aerial input Output: 2nd AUDIO OUT, VIDEO OUT Others: CD changer, OE REMOTE

AM: (MW) 522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 35 dB

DVD, fs=192 kHz: 16 Hz to 88 000 Hz

VCD/CD: 16 Hz to 20 000 Hz

Screen Size: 3.5 inch wide liquid crystal display

Number of Pixel: 211 200 pixels: 960 (horizontal) × 220 (vertical)

Drive Method: TFT (Thin Film Transistor) active matrix format

Color System: PAL/NTSC

MONITOR

Aspect Ratio: 16:9 (wide)

Allowable Storage Temperature: –10°C to +60°C

Allowable Operating Temperature: 0°C to +40°C

USB Standards: USB 1.1

Data Transfer Rate Full Speed: Maximum 12 Mbytes

Low Speed: Maximum 1.5 Mbytes

USB

Compatible Device: Mass storage class

Compatible File System: FAT 32/16/12

Max. Current: Less than 500 mA/5 V

Version: Bluetooth 1.2 certified

Output Power: +4 dBm Max. (Power class 2)

Service Area: Within 10 m

Profile: HSP (Headset Profile)

BLUETOOTH

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 160 mm

GENERAL

Mass (approx.): 2.1 kg (excluding accessories)

HFP (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile) SPP (Serial Port Profile) OPP (Object Push Profile)

Panel Size (approx.): 188 mm × 58 mm × 12 mm

ENGLISH

Design and specifications are subject to change without notice.

REFERENCES

Bitte lesen Sie die Anleitung vollständig durch, bevor Sie das Gerät in Betrieb nehmen, um sicherzustellen, daß Sie

alles vollständig verstehen und die bestmögliche Leistung des Geräts erhalten.

Wir danken Ihnen für den Kauf eines JVC Produkts.

WICHTIG FÜR LASER-PRODUKTE

1. LASER-PRODUKT DER KLASSE 1

2. ACHTUNG: Die obere Abdeckung nicht öffnen. Das Gerät enthält keine Teile, die vom Benutzer gewartet

werden können. Wartungen nur von qualifziertem Fachpersonal durchführen lassen.

3. ACHTUNG: Sichtbare und/oder unsichtbare Laserstrahlung der Klasse 1M bei offenen Abdeckungen. Nicht

direkt mit optischen Instrumenten betrachten.

4. ANBRINGEN DES ETIKETTS: WARNHINWEIS-ETIKETT, AUSSEN AM GERÄT ANGEBRACHT.

DEUTSCH

WARNUNGEN:

Dieses Symbol ist nur in der Europäischen Union gültig.

Benutzerinformationen zur Entsorgung alter Geräte

Dieses Symbol zeigt an, dass das damit gekennzeichnete Produkt nicht als normaler Haushaltsabfall entsorgt werden soll. Wenn Sie dieses Produkt entsorgen möchten, halten Sie sich dabei bitte an die entsprechenden Landesgesetze und andere Regelungen in Ihrem Land bzw. Ihrer Gemeinde. Die korrekte Entsorgung dieses Produkts dient dem Umweltschutz und verhindert mögliche Schäden für die Umwelt und die menschliche Gesundheit.

Um Unfälle und Schäden zu vermeiden

• Installieren Sie Geräte over verdrahten Sie Kabel NICHT an folgenden Orten;

– die Handhabung von Lenkrad und Schalthebel

kann behindert werden.

– die Funktion von Sicherheitseinrichtungen wie

etwa Airbags kann behindert werden.

– die Sicht kann behindert werden.

• NICHT das Gerät beim Fahren bedienen.

Wenn Sie das Gerät beim Fahren bedienen

müssen, dürfen Sie nicht den Blick von der Straße nehmen.

• Der Fahrer darf während der Fahrt auf keinen Fall auf den Monitor sehen.

• Der Fahrer darf während der Fahrt keine Kopfhörer tragen.

Achtungshinweise am Monitor:

• Das in diesem Receiver eingebaute Displayfenster wurde mit hoher Präzision hergestellt, aber es lässt sich nicht ausschließen, dass fehlerhafte Bildpunkte vorhanden sind. Dies ist unvermeidbar und keine Fehlfunktion.

• Setzen Sie den Monitor keiner direkten Sonneneinstrahlung aus.

Aus Sicherheitsgründen wird eine nummerierte ID-Karte mit diesem Receiver mitgeliefert, und die gleiche IDNummer ist auf dem Chassis des Receivers aufgedruckt. Die Karte muss an sicherer Stelle aufbewahrt werden, da sie den Behörden bei der Identifikation des Geräts im Falle eines Diebstahls helfen kann.

• Bei extrem niedrigen oder hohen Temperaturen. – Chemische Veränderungen im Geräteinneren

führen zu Fehlfunktionen.

– Unter Umständen ist die Bildwiedergabe

verschwommen oder verlangsamt. Unter solchen Umständen sind Bild- und Tonwiedergabe asynchron oder die Bildqualität beeinträchtigt.

Zurücksetzen des Geräts

Inhalt

EINFÜHRUNG

Abspielbarer Disctyp ........................ 4

Vor dem Betrieb des Geräts .............. 5

• Ihre vorgegebenen Einstellungen (ausgenommen für

die registrierten Bluetooth-Geräte) werden ebenfalls gelöscht.

Zwangsweises Ausschieben einer Disc

NO EJECT?

EMERGENCY EJECT?

NO EJECT?

EMERGENCY EJECT?

• Wenn dies nicht funktioniert, setzen Sie das Gerät

zurück.

Für die Sicherheit...

• Die Lautstärke nicht zu laut stellen, da dadurch Außengeräusche überdeckt und das Autofahren gefährlich wird.

• Das Auto vor dem Durchführen von komplizierten Bedienschritten anhalten.

Temperatur im Auto...

Wenn Sie das Auto für lange Zeit in heißem oder kaltem Wetter parken, bitte warten, bis sich die Temperatur im Auto sich normalisiert hat, bevor Sie das Gerät einschalten.

Dieses Produkt beinhält urheberrechtlich geschützte Technik mit dem Schutz von U.S.-Patenten und anderen intellektuellen Eigentumsrechten. Der Gebrauch dieser urheberrechtlich geschützten Technik ist durch Macrovision genehmigen zu lassen und nur für den Heimgebrauch und die Betrachtung in begrenztem Ausmaß vorgesehen, soweit nicht ausdrücklich von Macrovision genehmigt. Rückwärtige Entwicklung oder Zerlegung ist verboten.

BEDIENUNG

Grundlegende Bedienung—

Bedienfeld ................................... 7

Grundlegende Bedienung—

Fernbedienung (RM-RK251) .......... 8

Rundfunkempfang .......................... 10

Bedienung der Disc .......................... 15

Dual-Zonen-Betrieb ......................... 28

USB-Vorgänge ................................. 31

Bluetooth®-Vorgänge—

Handy/Audio-Player ..................... 33

EXTERNE GERÄTE

Hören vom CD-Wechsler ................... 40

DAB-Tuner-Empfang ........................ 42

Hören vom iPod/D. player ................ 45

Hören von den anderen externen

Komponenten .............................. 46

EINSTELLUNGEN

Klang-Entzerrung ............................ 48

Zuweisung von Namen zu den

Quellen ........................................ 49

Menü-Bedienungen ......................... 50

ZUR BEZUGNAHME

Wartung ......................................... 60

Weitere Informationen zu Ihrem

Receiver ....................................... 61

Störungssuche ................................. 66

Technische Daten ............................ 70

DEUTSCH

Abspielbarer Disctyp

Disc-Typ Aufnahmeformat, Dateityp usw. Abspielbar

DVD DVD Video (Regionalcode: 2)*

DVD-Audio

DVD-ROM

DVD Recordable/Rewritable (DVD-R*2/-RW, +R/+RW*3)

DEUTSCH

• DVD-Video: UDF-Bridge

• DVD-VR

• DivX/MPEG1/MPEG2/JPEG/ MP3/WMA/WAV/AAC: Konform mit ISO 9660 Level 1, Level 2, Romeo, Joliet

• DVD-RAM kann nicht abgespielt

DVD-Video

DVD-VR (nur nicht-CPRM)

DivX/MPEG1/MPEG2

JPEG

MP3/WMA/WAV/AAC*

MPEG4

DVD+VR

werden.

Dual-Disc DVD Seite

Nicht-DVD-Seite

CD/VCD Audio CD/CD Text (CD-DA)/DTS-CD

VCD (Video-CD)

CD-ROM

CD-I (CD-I Ready)

CD Recordable/Rewritable (CD-R/-RW)

• Konform mit ISO 9660 Level 1, Level 2, Romeo, Joliet

CD-DA

MP3/WMA/WAV/AAC*

JPEG

DivX/MPEG1/MPEG2

MPEG4

*1 Bei Einlegen einer DVD-Videodisc mit einem unzulässigem Regionalcode, erscheint „Region code error“ im Monitor.

*2 Im „Multi-Border“-Format bespielte DVD-R ist ebenfalls abspielbar (ausgenommen für Dual-Layer-Discs). *3 Es ist möglich, finalisierte +R/+RW-Discs (nur Videoformat) abzuspielen. Die Verwendung von +R Doppel-Layer Discs wird nicht empfohlen. *4 Diese Einheit kann AAC-Dateien abspielen, welche mit iTunes codiert sind.

Achtung bei DualDisc-Wiedergabe

Die Nicht-DVD-Seite einer „DualDisc“ entspricht nicht dem „Compact Disc Digital Audio“-Standard. Deshalb wird die Verwendung der Nicht-DVD-Seite einer DualDisc auf diesem Produkt nicht empfohlen.

Vor dem Betrieb des Geräts

Beenden Sie die Display-Demonstration und stellen Sie die Uhr ein. (☞ auch Seiten 51 und 52)

• Bedienvorgänge werden in erster Linie als Bedienungsschritte mit den Tasten an der Einheit erklärt; die Tasten an der Fernbedienung fungieren aber häufig auf gleiche Weise, wenn sie die gleichen Bezeichnungen oder Symbole tragen.

Setup-Menü-Symbol

AV Menu

ENT

Setup

Aktuell gewähltes Menü

Enter

Anzeigesprache:

~ Einschalten. Ÿ Zeigen Sie das <AV Menu> an. ! Rufen Sie das <Setup>-Menü auf.

In dieser Anleitung werden englischsprachige Anzeigen zur Erklärung verwendet. Sie können die Anzeigesprache im Monitor wählen. (☞ Seite 52)

⁄ Wählen Sie <Display> ] <Demonstration>, und aktivieren Sie dann das Schirmbild

<Demonstration>.

Setup Display Demonstration

Display

Clock Disc Setup 1 Disc Setup 2 Tuner

Demonstration

Aktuell gewähltes Untermenü Aktuelle Einstellung

Demonstration

Wall Paper Scroll Tag Display Dimmer

Off

ENT

Exit

@ Beenden Sie die Display-Demonstrationen.

Wählen Sie <Off>.

Demonstration

Off

DEUTSCH

ENT

Exit

Fortsetzung auf nächster Seite

EINFÜHRUNG

DEUTSCH

(zweimal)

Clock

Time Set

12Hours/24Hours OSD Clock Clock Adjust

0:00

¤ Schalten Sie zum Menü <Setup>

zurück.

# Wählen Sie <Clock> ]<Time Set>,

und aktivieren Sie dann das Schirmbild <Time Set>.

‹ Stellen Sie die Uhrzeit ein.

Time Set

Hours

18 : 00

ENT

Exit

Time Set

Minutes

18 : 35

ENT

Exit

$ Schalten Sie zum Menü <Clock>

zurück.

› Wählen Sie <12Hours/24Hours>. % Aktivieren Sie das Schirmbild

<12Hours/24Hours>.

ﬁ Wählen Sie entweder das 12-Stunden-

oder das 24-Stunden-System.

12Hours/24Hours

12 Hours

24 Hours

ENT

Exit

^ Schalten Sie zum Menü <Clock>

zurück.

ﬂ Wählen Sie <Clock Adjust>. & Aktivieren Sie das Schirmbild <Clock

Adjust>.

‡ Wählen Sie die Einstellung für <Clock

Adjust>.

• Off : Hebt auf.

• Auto: Aktivieren Sie die automatische

Uhreinstellung mit den Uhrzeitdaten (CT) von einem UKW-RDS-Sender.

* Beenden Sie den Vorgang.

Zur Anzeige der Uhrzeig bei der Wiedergabe einer Videoquelle wählen Sie <Clock> = <OSD Clock> = <On>.

Grundlegende Bedienung — Bedienfeld

Wählen Sie die Quelle. TUNER = DAB = DISC (DVD/VCD/CD) = USB =CD-CH, iPod, D.PLAYER, oder EXT-IN =Bluetooth Phone

=Bluetooth Audio = AV-IN =(zurück zum Anfang)

• Sie können diese Quellen nicht wählen, wenn diese nicht bereit sind.

• Das Gerät einschalten.

• Schalten Sie das Gerät aus [Gedrückthalten].

• Dämpfen Sie den Klang (in eingeschaltetem Zustand).

• Anzeigen oder Löschen von <AV Menu>*

• Aktivieren Sie Voice Dialing [Gedrückthalten].

Stellen Sie die Lautstärke ein.

Displayfenster

• Zeigen Sie das <Dial Menu> an.

• Rufen Sie die <Redial>-Liste [Gedrückthalten] auf.

• Disc auswerfen.

• Die Bedienfeldneigung ändern (Tilt1 – Tilt4) [Halten, und dann drücken Sie].

• DISC/USB: Starten Sie die Wiedergabe.

• In Menüs: Enter. (

ENT

:[Gedrückthalten])

ENT

:[Drücken Sie]/

• TUNER/DAB: Die Frequenzbänder wählen.

• DISC/USB: Stoppen Sie die Wiedergabe.

• In Menüs: Zurück.

<AV Menu>-Schirmbilder

Sie können die Menür zur Einrichtung

4 / ¢

• TUNER/DAB: Suchen Sie nach Sendern/Ensembles.

• DISC/USB: Auswahl von Kapiteln/Tracks.

• In Menüs: Gehen Sie zum vorherigen/nächsten Schritt weiter.

• iPod/D.PLAYER: Auswahl der Tracks.

• Bluetooth Audio: Sprung rückwärts/Sprung vorwärts.

5 / ∞*

verschiedener Einstellungen verwenden. Das <AV Menu>-Schirmbild besteht aus den folgenden Untermenüs—Setup/Equalizer/

Sound/Disc Surround/Mode/List/Bluetooth/ Dual Zone.

• Einzelheiten siehe Seiten 50 bis 59.

*2 Zum Anbringen

• TUNER: Wählt die Festsender.

• DAB: Dienste wählen.

• DISC/USB: Nach Titeln/Ordnern suchen.

• In Menüs: Wählen Sie Gegenstände.

• iPod/D.PLAYER: Den Player auf Menü/Pause

Sie können die für die gewählte Quelle

schalten oder Wiedergabe stoppen.

• Bluetooth: Ein Gerät wählen.

Zum Ändern der Display-Information.

des Bedienfelds

geeignete Liste anzeigen, indem Sie 5 / ∞ gedrückt halten.

Aktivieren Sie den TA-

Standby-Empfang.

Zeigen Sie PTY-Vorwahlliste

an [Gedrückthalten].

Fernbedienungssensor

Setzen Sie das Gerät zurück.

• Nur verwenden, wenn eine Fehlfunktion im internen System auftritt.

Abnehmen des Bedienfelds*

BEDIENUNG

DEUTSCH

Grundlegende Bedienung — Fernbedienung (RM-RK251)

Batterie einsetzen

DEUTSCH

Wenn die Reichweite oder Wirksamkeit der Fernbedienung abnimmt, müssen beide Batterien ausgewechselt werden.

Vor der Verwendung der Fernbedienung:

• Richten Sie die Fernbedienung direkt auf den Fernbedienungssensor am Gerät.

• Setzen Sie den Fernbedienungssensor KEINEM intensiven Licht (direkte Sonneneinstrahlung oder künstliches Licht) aus.

Der Receiver ist mit LenkradFernbedienungsfunktion ausgestattet.

• Siehe Einbau/Anschlußanleitung (separate Druckschrift) zum Anschluss.

Achtung:

• Setzen Sie Batterien nicht Hitze oder Flammen aus.

WICHTIG:

Wenn Doppelzone aktiviert ist (☞ Seite 28), arbeitet die Fernbedienung nur zur Steuerung des DVD/CD-Players.

R03/LR03/AAA

Hauptelemente und Merkmale

1*1 • Einschalten.

• Dämpft den Klang in eingeschaltetem Zustand.

• Wenn diese Taste gedrückt gehalten wird, schaltet sich das Gerät ab (wenn es eingeschaltet ist).

2*1 Wählt die Quelle. 3*1 • Zeigt <Dial Menu> an.

• Zeigt die <Redial>-Liste wenn gedrückt gehalten.

• Nimmt ankommende Rufe entgegen.

4*1*2 Zum Einstellen des Lautstärkepegels. 5*1*2 Wählt den Surround-Modus. 6 • DVD/DivX 6: Zeigt das Disc-Menü.

•

VCD: Setzt die PBC-Wiedergabe fort (☞ Seite 23).

• DVD-VR: Zeigt das Originalprogramm-Schirmbild.

;

a s

7 • Nimmt Wahlen/Einstellungen vor.

• ~: Springt um 5 Minuten für DivX/MPEG1/ MPEG2 vor oder zurück.

• Tasten DISC +/–: Wechselt Discs für “CD-CH”.

8 Zeigt den On-Screen-Balken.

Ändert die Display-Information.

p Anzeige oder Löschen von <AV Menu>. q Für Disc-/USB-Bedienungen:

• 6: Spielt/pausiert.

• 5 / ∞

DVD: Wählt Titel/Gruppe DVD-VR: Wählt Programm/Playlist. USB/andere Discs (ausgenommen VCD/CD):

Wählt die Ordner.

• 4 / ¢:

Kurz drücken: Sprung rückwärts/Sprung vorwärts

– – Drücken und halten: Reverse-/Vorwärts-Suche

Für UKW/AM-Vorgänge:

• 5 / ∞: Wählt die Festsender.

• 4 / ¢: Fungiert zur Suche nach Sendern.

– Kurz drücken: Automatischer Suchlauf – Drücken und halten: Manueller Suchlauf

Bei DAB-Tunerbedienung:

• 5 / ∞: Wählt einen Dienst.

• 4 / ¢: Fungiert zur Suche nach Ensembles.

– Kurz drücken: Automatischer Suchlauf – Drücken und halten: Manueller Suchlauf

Für Apple iPod/JVC D. player Vorgänge:

• ∞: Pausiert/stoppt oder setzt die Wiedergabe fort.

• 5: Ruft das Hauptmenü auf (und dann 5 / ∞ / 4 / ¢ fungieren als Menüwahltasten).*

• 4 / ¢ (im Menü-Wahlmodus)

– Wählt einen Gegenstand bei kurzem Drücken.

(Dann drücken Sie ∞ zum Bestätigen der Wahl).

– Überspringt 10 Gegenstände wenn gedrückt

gehalten.

Für Bluetooth-Vorgänge:

• 5 / ∞: Wählt ein registriertes Gerät.

• 4 / ¢: Rückwärts-Sprung/Vorwärts- Sprung (für Audio-Betrieb).

• 6: Nimmt ankommende Rufe entgegen

(für „Bluetooth Phone“).

Spielt/pausiert (für „Bluetooth Audio“).

In Menüs:

• 5 / ∞: Wählen Sie Gegenstände.

• 4 / ¢: Geht zum vorherigen/nächsten Schritt weiter.

w TUNER/DAB: Wählt die Frequenzbänder. DISC/USB: Stoppen Sie die Wiedergabe. Bluetooth Phone: Beendet den Ruf. Bluetooth Audio: Spielt/pausiert. In Menüs: Zurück.

Stellt den Lautstärkepegel über den Anschluss

2nd AUDIO OUT ein. (☞ Seite 28)

Aktiviert oder deaktiviert die Doppelzone.

r* t*1*2 Wählt den Klangmodus. y • DVD-Video/DivX 6: Zeigt das Disc-Menü.

• VCD: Setzt die PBC-Wiedergabe fort. (☞ Seite

23)

• DVD-VR: Zeigt das Playlist-Schirmbild.

u RETURN-Taste

• Bei VCD: Schaltet zum PBC-Menü zurück.

i DISC/USB: Schaltet den Zahlen-Eingabemodus

um.

• Fungiert auch als CLEAR-Taste, um nach einer Fehleingabe die falsche Zahl zu löschen.

o Geben Sie Zahlen ein. (☞ Seite 12, 21 bis 23, 38

und 43)

• CD-Wechsler: Wählt die Disc direkt.

• Tuner: Wählt die Festsender.

;*1 Ändert das Seitenverhältnis der

Wiedergabebilder.

a Reverse-/Vorwärts-Suche für Disc-/USB-

Vorgänge.

s • DVD-Video: Wählt die Audio-Sprache (

die Untertitel (

) oder den Winkel ( ).

• DVD-Audio: Wählt den Audio-Stream ( ).

• DVD-VR: Ein-/Ausschalten von Untertiteln ( ) und wählt den Audio-Kanal ( ).

• DivX: Wählt die Audio-Sprache ( ), oder die Untertitel ( ).

• VCD: Wählt den Audio-Kanal ( ).

*1 Wenn Doppelzone aktiviert ist, können diese Tasten

nicht verwendet werden.

*2 Diese Tasten können nur verwendet werden, wenn

der Schiebedeckel geschlossen ist.

*3 5 : Schaltet zum vorherigen Menü zurück. ∞ : Bestätigt die Auswahl.

DEUTSCH

BEDIENUNG

Rundfunkempfang

POWER]ON

Wellenbereich

TUNER

FM1 Preset1

Vorwahl-Nr.

Sendernamen (PS) für UKW-RDS. Wenn kein Signal anliegt, erscheint „No Name“.

FLAT

Pop M

Bayern Radio

87.5 MHz

DEUTSCH

Wählen Sie „TUNER“.

Tuner-/StandbyEmpfangsanzeigen

DXMOAFTP

15: 45

PTY-Code für UKW RDS

Ÿ Wählen Sie die Frequenzbänder. ! Suchen Sie einen Sender—Automatischer Suchlauf.

• Manueller Suchlauf: Halten Sie entweder 4 oder ¢ gedrückt, bis „Manual Search“ im Display erscheint, und drücken Sie dann wiederholt.

• Die ST-Anzeige leuchtet auf, wenn eine UKW-Stereo-Sendung mit ausreichender Signalstärke empfangen wird.

Wenn Sie Schwierigkeiten haben, eine Sendung in Stereo zu empfangen

AV Menu

Setup

AV Menu

ENT

Enter

Mono

Off

Der Empfang wird besser, jedoch geht der StereoEffekt verloren.

• Die MO-Anzeige leuchtet auf.

Zum Wiederherstellen des Stereoeffekts wählen

Sie <Off > in Schritt 4.

☞ Seite 48

ENT

Exit

Mode

Modusmenü-Symbol

Mode

Off

Mono

DX/Local SSM PTy Standby

ENT

Enter

Zum Abstimmen von Sendern mit ausreichender Signalstärke

Diese Funktion arbeitet nur bei UKW-Sendern. Wenn Sie diese Funktion aktiviert haben (<Local> gewählt haben), arbeitet sie immer bei der Suche nach UKW-Sendern.

AV Menu

Setup

AV Menu

Mode

Modusmenü-Symbol

Mode

Mono

DX/Local

SSM PTy Standby

DX/Local

Local

ENT

Enter

ENT

Enter

ENT

Exit

Es wird nur nach Sendern mit ausreichender Signalstärke gesucht.

• Die DX-Anzeige erlischt, und die LO Anzeige leuchtet auf.

Automatische Voreinstellung von UKW-Sendern—SSM (StrongStation Sequential Memory)

Diese Funktion arbeitet nur bei UKW-Sendern. Sie können für jedes Frequenzband bis zu sechs Sender voreinstellen.

AV Menu

Setup

ENT

Enter

AV Menu

Mode

ENT

Enter

Modusmenü-Symbol

Mode

Mono DX/Local

SSM

PTy Standby

ENT

Start

Die lokalen UKW-Sender im ausgewählten Frequenzband mit den stärksten Signalen werden automatisch als Festsender gespeichert.

Manuelle Voreinstellung

Beisp.: Speichern des UKW-Senders 92,5 MHz unter

der Festsendernummer 4 des Frequenzbands FM1.

2 Stimmen Sie einen als Festsender

einzugeben gewünschten Sender ab.

No Name

92.5 MHz

Wählen Sie eine Festsendernummer.

Der in Schritt 2 gewählte Sender ist jetzt unter der Festsendernummer 4 gespeichert.

* Jedesmal wenn Sie die Taste gedrückt halten,

können Sie die UKW-Wellenbereiche umschalten.

• Auf die Vorwahlliste kann auch über <AV Menu> = <List> zugegriffen werden. (☞ Seite 12)

FM1 Store

87.5

89.9

97.9

105.9

108.0

107.9

Die Voreingabe-Liste erscheint.*

FM1 Store

87.5

89.9

97.9

105.9

108.0

107.9

TUNER

FM1 Preset4

No Name

92.5 MHz

ENT

BEDIENUNG

DEUTSCH

ENT

Wählen von Festsendern

An der Fernbedienung:

oder

Am Gerät:

DEUTSCH

oder

• Jedesmal wenn Sie die Taste gedrückt halten, können Sie die UKW-Wellenbereiche umschalten.

• Auf die Vorwahlliste kann auch über <AV Menu>

FM1 Store

87.5

89.9

97.9

92.5

108.0

107.9

= <List> zugegriffen werden.

AV Menu

Setup

AV Menu

List

Listenmenü-Symbol

FM1 Store

87.5

89.9

97.9

92.5

108.0

107.9

ENT

Enter

ENT

Enter

Die folgenden Merkmale stehen nur für UKW-RDSSender zur Verfügung.

Suchen nach UKW RDSProgramm—PTY-Suchlauf

Sie können Ihre ausgestrahlten Lieblingsprogramme suchen, indem Sie den PTY-Code Ihrer Lieblingsprogramme wählen.

Die verfügbaren PTY-Codes erscheinen

ENT

(einschließlich sechs Vorwahl-PTY-Codes).

2 Wählen Sie einen PTY-Code.

ENT

Wenn ein Sender eine Sendung mit dem PTY-Code ausstrahlt, den Sie gewählt haben, wird dieser Sender eingestellt.

Verfügbare PTY-Codes:

PTy Search

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

PTy Search

Cultures

Science

Varied Speech Pop Music Rock Music Easy Listening

TUNER

FM1

PTy Search XX.X MHz

FLAT

Science

DXAF

Die Frequenz ändert sich während der Suche.

ENT

15: 45

Speichern Ihrer bevorzugten Programmtypen

Sie können Ihre bevorzugten PTY-Codes unter der PTYVorwahlliste abspeichern.

PTy Search

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

ENT

Die verfügbaren PTY-Codes erscheinen (einschließlich sechs Vorwahl-PTY-Codes).

2 Wählen Sie einen PTY-Code zum Speichern in

der Liste.

PTy Search

Cultures

Science

Varied Speech Pop Music Rock Music Easy Listening

ENT

Die aktuelle PTY-Vorwahlliste erscheint im Display.

PTy Memory

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

ENT

3 Wählen Sie einen aufgelisteten Code zum

Austausch mit dem neu gewählten.

PTy Memory

Pop Music

Rock Music

Easy Listening

Serious Classics

Current Affairs

Varied Speech

Jetzt wird <Current Affairs> durch <Science> ersetzt.

ENT

Aktivieren/Deaktivieren von TA/ PTY-Standbyempfang

TA-Standbyempfang Anzeige

Drücken Sie

zum Aktivieren.

Das Gerät schaltet kurzzeitig auf Verkehrsansagen (TA) von anderen Quellen als AM, falls verfügbar. Die Lautstärke schaltet auf den voreingestellten TA-Lautstärkepegel um, wenn der aktuelle Pegel niedriger als der vorgegebene Pegel ist (☞ Seite 54).

Noch nicht aktiviert. Stimmen Sie auf einen anderen Sender, der Radio Data System-Signale ausstrahlt, um.

Drücken Sie

zum Deaktivieren.

PTY-Standbyempfang Anzeige

Aktivieren Sie <AV Menu> und wählen dann <Mode>, <PTy Standby> (☞ Seite 14, 57).

Das Gerät schaltet kurzzeitig auf Ihr bevorzugtes PTY-Programm von einer anderen Quelle als AM um.

Noch nicht aktiviert. Stimmen Sie auf einen anderen Sender, der Radio Data System-Signale ausstrahlt, um.

Zum Deaktivieren wählen Sie <Off> in Schritt 4 und drücken dann ENT einmal (☞ Seite 14).

Leuchtet auf

Blinkt

Erlischt

PTY

Leuchtet auf

Blinkt

Erlischt

DEUTSCH

• Wenn ein DAB-Tuner angeschlossen ist, arbeitet TAStandby/PTY-Standby-Empfang auch für den DABTuner.

BEDIENUNG

Aktivieren von PTY- Standbyempfang

DEUTSCH

Wählen Sie einen PTY-Code für PTY-

Standbyempfang.

AV Menu

Setup

AV Menu

Mode

Modusmenü-Symbol

Mode

Mono DX/Local SSM

PTy Standby

Off

PTy Standby

Off

News

PTy Standby

Drama Cultures

Science

Varied Speech Pop Music

ENT

Enter

Verfolgen des gleichen Programms—NetworkTracking-Empfang

Wenn Sie in einem Bereich unterwegs sind, in dem kein guter UKW-Empfang möglich ist, sucht dieser Receiver automatisch nach anderen Frequenzen, auf denen das UKW-RDS-Programm möglicherweise besser empfangen werden kann.

Programm A wird in unterschiedlichen Frequenzbereichen ausgestrahlt (01 – 05)

Bei Versand ab Werk ist der Network-Tracking-Empfang aktiviert.

Zum Ändern der Einstellung des NetzwerkTracking-Empfangs siehe <AF Regional> auf Seite

54.

• Wenn der DAB-Tuner angeschlossen ist, siehe auch

Exit

„Dynamische Programmverfolgung— Alternativfrequenzempfang (DAB AF)“. (☞ Seite 44)

Automatische Senderauswahl— Programmsuche

Normalerweise wird er aktuelle Sender abgestimmt, wenn Sie Festsender wählen. Wenn die Signale vom Radio Data System-UKWFestsender nicht mit ausreichender Signalstärke empfangen werden können, wählt das Gerät mithilfe der AF (Alternativfrequenz)-Daten eine andere Frequenz mit demselben Programm wie der Festsender aus. (☞ Seite 54)

• Das Gerät benötigt eine gewisse Zeit, um bei Programm-Suchlauf auf einen anderen Sender abzustimmen.

Bedienung der Disc

Der Disc-Typ wird automatisch erkannt, und die Wiedergabe startet automatisch (bei manchen Discs: automatischer Start hängt vom internen Programm ab).

Wenn eine Disc kein Disc-Menü hat, werden alle Tracks darauf wiederholt abgespielt, bis Sie die Quelle umschalten oder die Disc entnehmen.

“ im Monitor erscheint, kann das Gerät nicht den gewünschten Bedienvorgang akzeptieren.

Wenn „

• In manchen Fällen wird zwar „ “, nicht angezeigt, aber der Bedienvorgang ist dennoch nicht möglich.

Disc einsetzen.

Wiedergabe beginnt automatisch.

Beschriftungsseite

Achtung:

Stecken Sie keinen Finger hinter das Bedienfeld.

Achtung bei der Lautstärkeeinstellung:

Discs und angeschlossene USB-Geräte erzeugen im Vergleich zu anderen Tonträgern sehr wenig Rauschen. Senken Sie die Lautstärke vor dem Abspielen einer Disc, um Beschädigung der Lautsprecher durch plötzliche Tonspitzen zu vermeiden.

DEUTSCH

7: Stoppen Sie die Wiedergabe.

0: Disc auswerfen.

DISP: Drücken Sie hier, wenn kein Wiedergabebild erscheint, aber das

Disc-Information-Schirmbild (

DISC

Now Reading ...

3: Starten Sie die Wiedergabe, wenn erforderlich.

☞ Seiten 16 bis 18) erscheint.

15: 45

BEDIENUNG

Während der Wiedergabe der folgenden Discs drücken Sie .

• Bei jedem Drücken der Taste erscheinen das Wiedergabebild und die Disc-Informationsschirmbilder abwechselnd.

Disc-Typ

DVD

Audio-Format

DIGITALVIDEO

Surround-Modus

MULTI

T 01 C 02 0:45:38

DEUTSCH

4 ¢ Drücken Sie: Kapitel wählen Gedrückthalten: Reverse-/Vorwärts-Suche

5 ∞ Titel wählen

4 ¢ Drücken Sie: Kapitel wählen

Gedrückthalten: Reverse-/Vorwärts-Suche 5 ∞ Wählen Sie Programm-Nr./Playlist-Nr.

VR-PR: Originalprogramm VR-PL: Playlist

DVD

P 01 C 02 0:45:38

AUDIO

DVD

G 01 02 0:45:38

CHAP. RPT

15: 45

Wiedergabemodus

Titel-Nr./Kapitel-Nr./ Spielzeit

FLATDIGITALVR-PR

15: 45

Programm-Nr. (oder Playlist-Nr.)/KapitelNr./Spielzeit

Gruppen-Nr./Track-Nr./Spielzeit

MULTIMLP

BONUS

B.S.P

RPT

15: 45

4 ¢ Drücken Sie: Track wählen Gedrückthalten: Reverse-/Vorwärts-Suche 5 ∞ Gruppe wählen

BONUS-Anzeige (

☞ Seite 24)

B.S.P-Anzeigen (☞ Seite 24)

DVD

DivX

T 01 C 02 0:45:38

Current Folder Name Current File Name.avi

FRONT 2CH

RPT

15: 45

DEUTSCH

4 ¢ Drücken Sie: Track wählen Gedrückthalten: Reverse-/Vorwärts-Suche für DivX/MPEG

5 ∞ Drücken Sie: Ordner wählen Gedrückthalten: Ordnerliste anzeigen

4 ¢ Drücken Sie: Track wählen Gedrückthalten: Reverse-/Vorwärts-Suche

*1 Suchgeschwindigkeit: x2 ] x10.

Suchgeschwindigkeit: ¡1 ] ¡2.

Bei DivX/MPEG: Ordner-Nr./Track-Nr./Spielzeit Bei JPEG: Ordner-Nr./Datei-Nr.

PBC-Anzeige leuchtet auf, wenn PBC verwendet wird.

☞ Seite 48

VCD

02 0:45:38

Track-Nr./Spielzeit

FLATPBC

15: 45

BEDIENUNG

☞ Seite 48

DEUTSCH

4 ¢ Drücken Sie: Track wählen Gedrückthalten: Reverse-/Vorwärts-Suche

Gedrückthalten: Reverse-/Vorwärts-Suche 5 ∞ Drücken Sie: Ordner wählen Gedrückthalten: Ordnerliste anzeigen

02 0:45:38 Disc Title Artist Name Current Track Title

Track-Titel (nur für CD-Text)

Audio-Format (MP3/WMA/WAV/AAC)

MP3

T 01 02 0:45:38

Current Folder Name Current File Name.mp3

Tag-Daten werden anstelle von Ordner/Datei-Namen angezeigt, wenn sie aufgezeichnet sind wenn <

Display> auf <On> gestellt ist. (☞ Seite 51)

RPT

FLAT

15: 45

FLAT

15: 45

Ordner-Nr./Track-Nr./Spielzeit4 ¢ Drücken Sie: Track wählen

☞ Seite 48

Track-Nr./SpielzeitDisc-Titel/Interpretenname/

Tag

*1 Suchgeschwindigkeit: x2 ] x10. *3 „No Name“ erscheint bei herkömmlichen CDs.

Auswählen von Wiedergabemodi

Sie können nur einen der folgenden Wiedergabemodi wählen—Anspielen/Wiederholen/Zufall. Beispiel: Zur Wahl von Track-Wiederholung

AV Menu

Mode

Off

All Off Intro

Repeat

Random

Setup

AV Menu

ENT

Enter

Repeat

Off

Track

Folder

ENT

Set

Wenn einer der Wiedergabemodi gewählt ist,

Mode

Modusmenü-Symbol

ENT

Enter

leuchtet die entsprechende Anzeige im DiscInformation-Schirmbild auf.

Zum Abbrechen wählen Sie <All Off> in Schritt 3 oder <Off> in Schritt 4.

Disc-Typ Intro (Anspielfunktion) Repeat (Wiederholung) Random (Zufallswiedergabe)

Chapter: Wiederholt aktuelles

—

Kapitel

—

Title: Aktuellen Titel wiederholen

— Track: Wiederholt aktuellen Track —

Chapter: Wiederholt aktuelles

Kapitel

—

Program: Wiederholt das aktuelle

— Programm (nicht verfügbar für Playlist-Wiedergabe)

Track: Spielt die ersten 15

Sekunden jedes Tracks an (für VCD: wenn PBC nicht aktiviert ist)

Track: Spielt die ersten 15

Sekunden jedes Tracks an

Folder: Spielt die ersten

15 Sekunden des ersten Tracks jedes Ordners an

Track: Wiederholt aktuellen Track

(für VCD: wenn PBC nicht aktiviert ist)

Track: Wiederholt aktuellen Track Folder: Wiederholt alle Tracks des

aktuellen Ordners

Disc (All): Spielt alle Tracks in

zufälliger Reihenfolge ab (für VCD: wenn PBC nicht aktiviert ist)

Folder: Spielt in zufälliger

Reihenfolge alle Tracks des aktuellen Ordners ab, und dann Tracks der nächsten Ordner

Disc (All): Spielt alle Tracks in

zufälliger Reihenfolge ab

Track: Wiederholt aktuellen Track

—

Folder: Wiederholt aktuellen

Ordner

—

DEUTSCH

—

Folder: Wiederholt aktuellen

Ordner

—

BEDIENUNG

Wählen von Tracks auf der Liste

Wenn die Disc Ordner enthält, können Sie die Ordner/ Track (Datei)-Liste anzeigen und dann die Wiedergabe starten.

Folder List

Off

My Best

Cinema Pops My Best2 Favorite Song Cinema2

ENT

Auswurfsperre

Sie können für die eingelegte Disc eine Auswurfsperre aktivieren.

NO EJECT?

EMERGENCY EJECT?

„No Eject“ erscheint.

Die Ordner-Liste erscheint.

DEUTSCH

• Halten Sie die Taste gedrückt, um zu nächsten/ vorherigen Ordnern zu gehen.

2 Wählen Sie einen Ordner und aktivieren Sie

dann die Track-Liste.

Folder List

My Best Cinema Pops

My Best2

Favorite Song Cinema2

Off

ENT

Die Trackliste des gewählten Ordners erscheint.

3 Wählen Sie einen Track und starten Sie die

Wiedergabe.

File List

Song011.mp3 Song012.mp3 Song013.mp3

Song014.mp3

Song015.mp3 Song016.mp3

Off

• Auf die Vorwahlliste kann auch über <AV Menu> = <List> zugegriffen werden.

AV Menu

Setup

AV Menu

ENT

Enter

Um die Sperre aufzuheben, wiederholen Sie das gleiche Verfahren, und wählen Sie „EJECT OK?“.

List

Listenmenü-Symbol

ENT

Enter

Bedienverfahren mit der Fernbedienung —RM-RK251

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*2 (Es wird kein Ton gehört).

(Zeitlupe*

: Drücken Sie: Kapitel wählen (bei Wiedergabe oder

Gedrückthalten: Reverse-/Vorwärts-Suche.*

: Titel wählen (bei Wiedergabe oder Wiedergabepause).

im Pausebetrieb. Es wird kein Ton gehört).

Wiedergabepause).

DEUTSCH

*1 Löscht die Fehleingabe der

Zahl.

*2 Suchgeschwindigkeit: x2 ] x5

] x10 ] x20 ] x60

*3 Zeitlupengeschwindigkeit:

1/32 ] 1/16 ] 1/8 ] 1/4 ] 1/2

*4 Suchgeschwindigkeit: x2 ]

x10

= = : Kapitel wählen. Titel wählen (wenn nicht auf

Wiedergabe geschaltet).

(zweimal) = = : Titel wählen (bei Wiedergabe oder

Wiedergabepause). : Wählen Sie ein Bildverhältnis. : Zur Auswahl der Audiosprache :

Zur Auswahl der Untertitelsprache

Verwendung der menügesteuerten Merkmale

1 2 Wählen Sie einen

Gegenstand zum Start der Wiedergabe.

: Betrachtungswinkel wählen.

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*

: Drücken Sie: Track wählen.

Gedrückthalten: Reverse-/Vorwärts-Suche.*

: Gruppe wählen.

Verwendung der

= = : Track wählen.

(zweimal) = = : Gruppe wählen.

: Wählen Sie ein Bildverhältnis. : Wählen Sie den Audio-Stream.

menügesteuerten Merkmale

1 2 Wählen Sie einen

Gegenstand zum Start der Wiedergabe.

BEDIENUNG

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*2 (Es wird kein Ton gehört). : Drücken Sie: Track wählen.

Gedrückthalten: Reverse-/Vorwärts-Suche.*

(Es wird kein Ton

gehört).

: Ordner wählen.

DEUTSCH

Tracks wählen (innerhalb des gleichen

Ordner wählen.

Während der Wiedergabe...

Schalten Sie die Szenen um 5 Minuten zurück/vor.

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn

bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*4 (Es wird

(Zeitlupe*5 im Pausebetrieb. Es wird

Reverse-Zeitlupe arbeitet nicht.

Gedrückthalten: Reverse-/Vorwärts-

Wählen Sie eine Playlist (bei Wiedergabe oder Wiedergabepause).

kein Ton gehört).

: Drücken Sie: Kapitel wählen (im

Wiedergabe- oder Pausebetrieb).

Suche.*

: Wählen Sie Programm

: Wählen Sie ein Bildverhältnis.

= = :

Ordners).

(zweimal) = = :

: Wählen Sie ein Bildverhältnis.

: Zur Auswahl der Audiosprache (nur DivX)

: Zur Auswahl der Untertitelsprache (nur DivX)

Aktuelle Wiedergabeposition:

2. Drücken

1. Drücken

: Audiokanal wählen

(ST: Stereo, L: links, R: rechts).

: Schalten Sie den Untertitel ein/aus.

= = : Kapitel wählen. Wählen Sie Programm (wenn nicht die Wiedergabe

läuft).

(zweimal) = = Wählen Sie Programm/Playlist (bei Wiedergabe oder

Wiedergabepause).

Verwendung von Originalprogramm/PlaylistSchirmbildern (☞ Seite 30)

1 Für Originalprogramme: Für Playlist: 2 Wählen Sie einen Gegenstand zum

Start der Wiedergabe.

3 (Bildschirm verstecken)

Bei DivX6: Verwendung der menügesteuerten Merkmale

1 2 Wählen Sie einen

Gegenstand zum Start der Wiedergabe.

3. Drücken

2. Drücken

: Stoppen Sie die

Wiedergabe.

: Starten Sie die Wiedergabe. (Diashow:

Jede Datei wird einige Sekunden lang gezeigt).

Zeigt die aktuelle Datei, bis sie geändert

wird, wenn bei Diashow gedrückt.

: Track wählen.

: Stoppen Sie die

Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn

bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*

: Drücken Sie: Track wählen.

Gedrückthalten: Reverse-/Vorwärts-

Suche.*

: Ordner wählen.

: Wählen Sie ein Bildverhältnis.

= = :

Tracks wählen (innerhalb des gleichen

Ordners).

(zweimal) = = :

Ordner wählen.

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn

bei Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*

(Vorwärts-Zeitlupe*5 im Pausebetrieb.

Es wird kein Ton gehört).

Reverse-Zeitlupe arbeitet nicht.

: Drücken Sie: Track wählen.

Gedrückthalten: Reverse-/Vorwärts-

Suche.*6 (Es wird kein Ton gehört.) : Wählen Sie ein Bildverhältnis. : Audiokanal wählen (ST: Stereo, L: links,

R: rechts).

: Stoppen Sie die Wiedergabe.

: Starten Sie Wiedergabe/Pause (wenn bei

Wiedergabe gedrückt).

: Reverse-/Vorwärts-Suche.*

: Drücken Sie: Track wählen.

Gedrückthalten: Reverse-/Vorwärts-Suche.*

= = : Track wählen.

: Ordner wählen.

= = :

Tracks wählen (innerhalb des gleichen Ordners).

(zweimal) = = :

Ordner wählen.

= = : Track wählen.

Bei der PBC-Wiedergabe...

= = :

Wählen Sie einen Punkt im Menü. Zum Zurückschalten zum vorherigen Menü drücken

Sie

Zum Beenden der PBC-Wiedergabe

2 Starten Sie den gewünschten Track.

= =

• Zum Fortsetzenb von PBC drücken Sie / .

*1 Löscht die Fehleingabe der Zahl. *2 Suchgeschwindigkeit: ¡1 ] ¡2 ]

¡3

*3 Suchgeschwindigkeit: ¡1 ] ¡2 *4 Suchgeschwindigkeit: x2 ] x5 ] x10 ] x20

] x60

*5 Zeitlupengeschwindigkeit: 1/32 ] 1/16 ]

1/8 ] 1/4 ] 1/2

*6 Suchgeschwindigkeit: x2 ] x10

DEUTSCH

BEDIENUNG

Wiedergabe einer Bonus-Gruppe

Wenn eine DVD-Audio mit einer „Bonusgruppe“ erkannt wird, leuchtet die BONUSAnzeige im Disc-Information-Schirmbild auf.

Zur Wiedergabe einer Bonus-Gruppe...

1 Wählen Sie die Bonus-Gruppe.

• Die Bonusgruppe ist normalerweise als letzte

Gruppe einer Disc aufgezeichnet.

2 Geben Sie die Schlüsselnummer ein.

DEUTSCH

Position

• „Schlüsselnummer“ (eine Art Passwort) für die

: Bewegen Sie die Eingabe-

: Wählen Sie eine Zahl

Bonus-Gruppe ist nicht frei zugänglich. Die Art der Mitteilung der Schlüsselnummer ist je nach Disc unterschiedlich.

3 Folgen Sie den interaktiven Anweisungen im

Monitor.

Wählen eines durchsuchbaren Standbildes

Wenn eine Disk mit durchsuchbaren Standbildern erkannt wird, leuchtet die B.S.P-Anzeige im DiskInformation-Schirmbild auf.

Wenn die Disc die BSP-Wahlsymbole wie @ oder # im Schirmbild zeigt...

1 Wählen Sie einen zur Anzeige gewünschten

Gegenstand.

Genießen von Surroundklang

Sie können Mehrkanal-Surround-Wiedergabe über die vorderen und mittleren Surroundlautsprecher genießen.

• Nach dem Anschließen des Center-

Lautsprechers stellen Sie sicher, den CenterLautsprecher zu aktivieren; andernfalls kommt kein Ton vom Center-Lautsprecher (☞

Seite 53).

• All-Surround-Modus kann auch für „USB“ verwendet werden.

MULTI: Für mehrkanalig codierte Quellen wie

Dolby Digital* aktiviert erscheint „MULTI“ im Disc-InformationSchirmbild.)

Dolby Pro Logic II (Movie/Music): Für 2-Kanal-

Quellen ausgenommen für DivX/MPEG1/MPEG2Discs.

Zum Einschalten von Surround

, DTS*2 und DVD-Audio. (Wenn

AV Menu

ENT

Setup

Disc-Surround-Menüsymbol

AV Menu

Disc Surround

Surround Off

Surround On

Enter

ENT

Enter

Auto

• Surround Off: Deaktiviert die

Surroundfunktion.

• Surround On: Aktiviert Surround = gehen Sie

zu den folgenden Schritten.

Surround On

Auto

Through Dolby PLII Movie Dolby PLII Music

ENT

Set

• Auto: Wenn Mehrkanal-Digitalsignale anliegen,

wird „MULTI“-Surround aktiviert.

Wenn 2-Kanal- oder 2,1-Kanal-Signale anliegen,

wird „4CH STEREO“ aktiviert.

• Through: Alle anliegenden Signale werden zu

den entsprechenden Lautsprechern geleitet.

• Dolby PLII Movie: Aktivieren Sie Dolby Pro

Logic II Movie.

• Dolby PLII Music: Aktiviert Dolby Pro Logic

II Music. Sie können die Einstellungen von <Panorama> und <Center Width> anpassen. (☞ unten)

Zum Ändern der Einstellung von <Dolby PLII Music>

in Schritt 4 oben...

Surround On

Auto Through Dolby PLII Movie

Dolby PLII Music

Panorama

Dolby PLII Music

Panorama

CenterWidth

An der Fernbedienung:

• Sie können nicht die Einstellungen für <Dolby PL II Music> mit der Fernbedienung ändern.

*1 Hergestellt unter Lizenz von Dolby Laboratories.

Dolby, Pro Logic und das Doppel-D-Symbol sind Warenzeichen von Dolby Laboratories.

*2 „DTS“ und „DTS Digital Surround“ sind eingetragene

Warenzeichen von DTS, Inc.

DEUTSCH

• Panorama: Wählen Sie <On> für den

„wraparound“ (Rundum)-Klangeffekt.

• Center Width: Stellen Sie das Klangbild

des Mittelkanals so ein, dass es nur über den Mittellautsprecher oder nur über den linken/ rechten Frontlautsprecher als „Phantom-Bild“ bzw. unterschiedliche Kombinationen dieser Lautsprecher vermittelt wird. Je höher die Nummer, desto stärker der „Phantomeffekt“ (normalerweise wählen Sie <4>).

BEDIENUNG

Bedienvorgänge mit dem On-Screen-Balken (DVD/VCD/DivX/MPEG1/ MPEG2/JPEG)

Diese Vorgänge sind mit dem Monitor unter Verwendung der Fernbedienung möglich.

1 Zur Anzeige des Bildschirm-Balkens. (☞ Seite

27)

DEUTSCH

2 Wählen Sie einen Parameter.

3 Treffen Sie eine Wahl.

Wenn ein Popup-Menü erscheint...

• Zur Eingabe von Zeit/Zahlen...

Position

: Bewegen Sie die Eingabe-

: Wählen Sie eine Zahl

Zum Entfernen des On-Screen-Balkens

On-Screen-Balken

Information

Bedienung

DVD -V

TIME TITLE CHAP

T02-C03 TOTAL 1:25:58

C. RPT

RPT

Das obige Beispiel zeigt DVD-Video. Auf der Leiste gezeigte Gegenstände sind je nach Disc-Typ unterschiedlich.

1 Disc-Typ 2 • DVD: Audiosignalformat

• VCD: PBC

3 Wiedergabemodus*

DVD-Video: T. RPT: Titel-Wiederholung C. RPT: Kapitel-Wiederholung DVD-Audio: T. RPT: Track-Wiederholung DVD-VR: C. RPT: Kapitel-Wiederholung PG. RPT: Programmwiederholung DivX/MPEG: T. RPT: Track-Wiederholung F. RPT: Ordner-Wiederholung JPEG: F. RPT: Ordner-Wiederholung VCD: T. INT: Track-Anspielen T. RPT: Track-Wiederholung A. RND: Alle zufällig 4 Wiedergabe-Information

T02-C03

Aktueller Titel/Kapitel

G02-T03

Aktuelle Gruppe/Track

PG-001

Aktuelles Programm/Kapitel

C-002

PL-003

C-004

Aktuelle Playlist/Kapitel

TRACK 01

Aktueller Track

F001-T001

Aktueller Ordner/Track Aktueller Ordner/Datei (JPEG)

F002-F002

5 Zeitanzeige

TOTAL

Verflossene Spielzeit der Disc

T. REM

Restliche Titelzeit (bei DVD)

Restliche Abspielzeit (bei anderen)

TIME

Bisherige Abspielzeit des aktuellen

Kapitels/Tracks*

REM

Restliche Abspielzeit des aktuellen

Kapitels/Tracks*

6 Wiedergabestatus

Wiedergabe

Reverse-/Vorwärts-Suche

Rückwärts-/Vorwärts-Zeitlupe Pause Stopp

7 Bedienungssymbole

TIME

Ändern Sie die Zeitanzeige (siehe 5) Zeit-Suche (Legen Sie eine bestimmte

Szene durch Eingabe der Zeit fest).

TITLE

Titelsuche (nach Nummer)

CHAP

Kapitelsuche (nach Nummer)

GROUP

Gruppensuche (nach Nummer)

TRACK

Tracksuche (nach Nummer)

RPT

Wiederholungswiedergabe*

INT

Anspielfunktion*

RND

Zufallswiedergabe*

Ändern Sie die Audio-Sprache, den

Audio-Kanal oder den Audio-Stream Ändern Sie die Untertitel-Sprache Ändern Sie den Sichtwinkel

PAGE

Ändern Sie die durchsuchbaren

Standbilder (Seiten)

DEUTSCH

*1 ☞ Seite 19 *2 Gilt nicht für DVD-VR.

BEDIENUNG

Dual-Zonen-Betrieb

Sie können eine Disc-Wiedergabe auf dem externen Monitor genießen, der an die Steckverbindungen VIDEO OUT und 2nd AUDIO OUT angeschlossen ist, während Sie eine andere Quelle über die Lautsprecher hören.

• Wenn Doppelzone aktiviert ist, können Sie nur den DVD/CD-Player mit der Fernbedienung steuern.

AV Menu

DEUTSCH

ENT

Setup

AV Menu

Dual Zone

Doppelzonemenü-Symbol

Dual Zone

Off On

On/Surround On

• Off : Deaktivieren Sie Doppelzone.

• On (DUAL): Aktiviert Doppelzone ohne Anlegen von Kopfhörer Surround*1.

• On/Surround On (DUAL-S): Aktiviert Doppelzone und legt Kopfhörer Surround an.

Wenn Doppelzone aktiviert ist, wird die Hauptquelle auf „DISC“ umgestellt.

DVD

T 01 C 02 0:45:38

Beispiel: Wenn „On/Surround On“ gewählt ist.

Enter

ENT

Enter

ENT

Set

FLATDIGITALVIDEO

DUAL-S

An der Fernbedienung:

2 Stellen Sie die Lautstärke über den Anschluss

2nd AUDIO OUT ein.

3 Bedienen Sie den DVD/CD-Player.

*1 JVC originales virtuelles Surroundsystem für

Kopfhörer. Diese Surroundfunktion arbeitet auch für die Hauptquelle „DISC“, wenn „On/Surround On“ als Nebenquelle gewählt ist. Diese Surroundfunktion arbeitet nicht bei DivX/MPEG1/MPEG2-Discs.

*2 Abgeblendet angezeigt, wenn Kopfhörer-Surround

nicht anliegt.

Bedienung mit dem Steuerschirmbild

Für Discs ausgenommen DVD und VCD:

Während Doppelzone eingeschaltet ist, sind diese Vorgänge sind mit dem externen Monitor unter Verwendung der Fernbedienung möglich. Das Steuerschirmbild erscheint automatisch, wenn Sie eine Disc einsetzen. (Für DivX/MPEG1/MPEG2/JPEG; während keine Wiedergabe läuft).

Zum Wählen deiner anderen Quelle (Hauptquelle) zum Hören über die Lautsprecher:

Drücken Sie SRC (Quelle) am Bedienfeld.

• Durch Verwendung der Tasten am Bedienfeld können Sie die neu gewählte Quelle bedienen, ohne den Doppelzonen-Betrieb (DISC) zu beeinflussen.

• Sie können nicht „USB“ für die Hauptquelle wählen.

Folder : 2 / 3

01 Music

02 Music

03 Music

Track Information

Album Weather Artist Robert M. Smith Title Rain

Track : 6 / 14 (Total 41)

Cloudy.mp3 Fair.mp3 Fog.mp3 Hail.wma Indian summer.mp3 Rain.mp3

Shower.mp3

Snow.mp3 Thunder.wma Typhoon.mp3 Wind.mp3 Winter sky.mp3

Beisp.: MP3/WMA

TIME 00:00:14T. RPT

JVC KD-AVX33 User Manual [en, de, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual

Playable disc type

Before operating the unit

Basic operations — Control panel

OPERATIONS

Basic operations — Remote controller (RM-RK251)

Listening to the radio

Disc operations

USB operations

Bluetooth® operations — Cellular phone/audio player

Listening to the CD changer

Listening to the DAB tuner

Listening to the iPod/D. player

Listening to other external components

Sound equalization

Assigning titles to the sources

Menu operations

Maintenance

More about this unit

Troubleshooting

Specifications