Page 1
KD-AVX33
5 mm
5 mm
Installation/Connection Manual
LVT1708-004A
[A]
This unit is designed to operate on 12 V DC , NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit and wire any cable in locations where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving. If the driver watches the monitor while driving, it
may lead to carelessness and cause an accident.
• The driver must not put on the headphones while driving. It is dangerous to shut off the outside sounds
while driving.
• If you need to operate the unit while driving, be sure to look around carefully.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback picture
will be shown.
– This warning appears only when the parking brake lead is connected to the parking brake system built
in the car.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear
and at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change “Amplifier Gain” setting to prevent the speakers from
being damaged (see page 51 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
0207MNMMDWJEIN
©2007 Victor Company of Japan, Limited
Parts list for installation and connection
The following parts are provided for this unit. After checking them, please set them correctly.
A / B
Hard case/Control panel
F
Audio/video cord
K
Microphone
C
Sleeve
G
Crimp connectors
L
Microphone clip
D
Trim plate
H
Remote controller / Holder
M
Reverse gear signal extension cord
E
Power cord
I
Batteries
J
Double-sided
adhesive tape
EN
Heat sink
Required space for installation
Control panel
Dashboard
Trim plate is detached on this
illustration for explanation.
N
Washer (ø5)
o
Lock nut (M5)
P
Handles
Q
Rubber cushion
Installing the remote controller
Holder
Caution when installing
Fit the unit into the mounting sleeve by using four corners of the trim plate.
• DO NOT press the panel (shaded in the illustration).
Remote controller
Double-sided
adhesive tape
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
• Make sure not to block the fan on the rear panel to maintain proper ventilation when installed.
• You cannot install the unit on the car which has any obstacles in the space shown in “Required space for installation” above.
R
Mounting bolt—
M5 x 20 mm
1
*
When you stand the unit,
be careful not to damage
the fuse on the rear.
Do not block the fan.
1
Do the required electrical connections.
Fit the protrusions
outside the unit.
Bend the appropriate
tabs to hold the sleeve
firmly in place.
Page 2
When using the optional stay When installing the unit without using the sleeve
Fire wall
Stay (option)
In a car having the “Required space for installation” (see page 1), first remove the car radio and install the
unit in its place.
Flat type screws—M5 x 8 mm
2
*
2
*
Not included for this unit.
Dashboard
Removing the unit
Before removing the unit, release the rear section.
Screw (option)
30˚
Install the unit at an angle of less than 30˚.
2
Bracket *
2
Bracket *
Flat type screws—M5 x 8 mm*
2
Note: When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws.
If longer screws are used, they could damage the unit.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
A
Connecting the parking brake lead
Connect the parking brake lead to the parking brake system built in the car.
Parking brake
Parking brake switch (inside the car)
Connecting the reverse gear signal lead (for rear view camera) (REVERSE GEAR SIGNAL)
B
Locate the reverse lamp lead in the trunk.
Parking brake lead (light green)
To metallic body or chassis of the car
Reverse lamp lead
Connecting the Mic unit
C
Reverse lamps
To reverse lamp
12
Microphone
or
Microphone clip
Secure the microphone cord using cord cramps (not supplied) if necessary.
Reverse lamp lead
To car battery
J
Double-sided adhesive tape
Adjust the microphone angle
Purple with white stripe
2
Page 3
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car ’s chassis again after installation.
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the
unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
To an external component
(see diagram
)
Rear ground terminal
Black
Yellow
Red
Blue
15 A fuse
4
*
USB cable (see diagram )
To metallic body or chassis of the car
To a live terminal in the fuse block
connecting to the car battery (bypassing the
ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
Ignition switch
Fuse block
To automatic antenna if any (250 mA max.)
3
*
Not included for this unit
4
*
Before checking the operation of this unit prior
to installation, this lead must be connected,
otherwise power cannot be turned on.
White with
black stripe
A
Connections for external component playback
White
Left speaker (front) Right speaker (front)
KS- HP2
Cordless headphones (not supplied) *
black stripe
5
Gray with
Blue with white stripe
Orange with white stripe
Brown
Light green
Gray
Green with
black stripe
To the remote lead of other equipment (200 mA max.)
To car light control switch
To cellular phone system
To parking brake (see diagram
Green
Left speaker (rear)
Purple with
black stripe
)
Purple
Right speaker (rear)
KV-MR9010
9-INCH WIDESCREEN
MONITOR (not supplied)
Video cord (not supplied)
Camcorder, rear view camera, etc.
Navigation System
5
*
To listen to disc playback sound while in Dual Zone operations (see page 26 of
INSTRUCTIONS).
6
*
Audio cord (not supplied)
3
Page 4
B
Connecting the external amplifiers
You can connect amplifiers to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
• For amplifier only:
– After you have connected the center speaker, make sure to activate the center speaker; otherwise, no sound comes out of the connected center speaker, see page 49 of the INSTRUCTIONS.
– Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
– You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat buildup. See page 51 of the INSTRUCTIONS (separate
volume).
Y-connector (not supplied for this unit)
Remote lead
Rear speakers
JVC Amplifier
Front speakers
JVC Amplifier
C
Connecting external components
Front speakers
Remote lead (Blue with white stripe)
To the remote lead of other equipment
JVC Amplifier
Subwoofer
Center speaker
JVC Amplifier
6
Audio cord (not supplied)
*
7
*
Firmly attach the ground wire to the metallic
body or to the chassis of the car—to the place
uncoated with paint (if coated with paint,
remove the paint before attaching the wire).
Failure to do so may cause damage to the unit.
You can connect external components in series as shown in the diagram below.
• All the components, adapters or signal cords need to be purchased separately.
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
• To use JVC CD changer, Apple iPod or JVC D. player, set “External Input” to “Changer/iPod/D.
Player” (see page 50 of the INSTRUCTIONS).
• To use other external components via KS-U57 or KS-U58, set “External Input” to “External
Input” (see page 50 of the INSTRUCTIONS)
JVC CD changer
CD changer jack
or
Apple iPod
KS-PD100
or
To disconnect the connector
JVC D. player
KS-PD500
or
External component
CD changer jack
USB devices
USB cable—
approx.1.2 m
Audio cord (not supplied)
External
component
or
External
component
3.5 mm stereo mini plug
USB device
Hold the connector top tightly (1),
then pull it out (2).
KS-U57*
or
• iPod is a trademark of Apple Inc.,
registered in the U.S. and other
KS-U58*
countries.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
8
External component
You cannot connect a computer to the USB ( ) terminal of the unit.
9
External component
8
*
Line Input Adapter KS-U57 (separately purchased)
9
*
Aux Input Adapter KS-U58 (separately purchased)
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
4
Loading...