JVC HR-S9700U Instruction Manual

Download

Page 1

VIDEO CASSETTE RECORDER

ENGLISH

CONTENTS

SAFETY FIRST 2

Safety Precautions ................................................2

INDEX 4 INSTALLING YOUR NEW RECORDER 10

Basic Connections ..............................................10

S-VIDEO Connection ..........................................11

INITIAL SETTINGS 12

Auto Set Up ........................................................12

Preset Download ................................................14

Language ............................................................16

SAT CONTROL SET 17

Satellite Receiver Control Setting ........................17

T-V LINK 19

T-V Link Functions .............................................19

PLAYBACK 20

Basic Playback ................................................... 20

Playback Features ...............................................21

TimeScan ........................................................... 24

RECORDING 26

Basic Recording ..................................................26

Recording Features .............................................27

B.E.S.T. Picture System .......................................31

TIMER RECORDING 32

Express Timer Programming ...............................34

Automatic Satellite Programme Recording ..........38

REMOTE CONTROL FUNCTIONS 39 VIDEO NAVIGATION 42

Navigation ..........................................................42

Edit Title .............................................................44

Find Title ............................................................48

EDITING 51

Edit From A Camcorder ......................................51

Output/Input Set ................................................. 52

Edit To Or From Another Video Recorder ...........54

Audio Dubbing ...................................................56

Insert Editing .......................................................58

Random Assemble Editing ..................................60

Synchro Editing ..................................................62

Information On J Terminal ..................................63

SYSTEM CONNECTIONS 64

Connecting To A Satellite Receiver .....................64

Connecting/Using A Decoder .............................66

Connecting/Using A Stereo System .....................67

SUBSIDIARY SETTINGS 68

Mode Set ............................................................68

Tuner Set ............................................................72

Video Channel Set ..............................................78

Clock Set ............................................................80

TROUBLESHOOTING 82 QUESTIONS AND ANSWERS 85 SPECIFICATIONS 86 LIST OF TERMS 87

HOWVIEW

Timer Programming ........................32

System Setup ..................................79

LPT0328-001A

Page 2

SAFETY FIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT

TO RAIN OR MOISTURE.

CAUTION

When you are not using the recorder for a long period of time, it is recommended that you disconnect

the power cord from the mains outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric

shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

WARNING

There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-West), and SECAM-B, used in Eastern European countries (also called SECAM-East).

1. This recorder can also receive SECAM-B colour television signals for recording and playback.

2. Recordings made of SECAM-B television signals produce monochrome pictures if played back on a video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).

3. SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce monochrome pictures when played back with this recorder.

4. This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L signals.

IMPORTANT

Please read the various precautions on pages 2 and 3 before installing or operating the recorder.

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without

the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

● Cassettes marked “S-VHS” and “VHS” can be used with this video cassette recorder. However, S-VHS recordings are possible only with cassettes marked “S-VHS”. By using the S-VHS ET function, it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.

● S

HOWVIEW

from Gemstar Development Corporation.

is a registered trademark of Gemstar Development Corporation. The S

HOWVIEW

system is manufactured under licence

Page 3

For Italy:

“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”

The STANDBY/ON operating current on and off. “

Video tapes recorded with this video recorder in the LP/EP (Long Play/Extended Play) mode cannot be played back on a single-speed video recorder.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

1. DO NOT place the recorder . . .

...in an environment prone to extreme temperatures or humidity. ...in direct sunlight. ...in a dusty environment. ...in an environment where strong magnetic fields are generated. ...on a surface that is unstable or subject to vibration.

2. DO NOT block the recorder’s ventilation openings.

3. DO NOT place heavy objects on the recorder or remote control.

4. DO NOT place anything which might spill on top of the recorder or remote control.

5. AVOID violent shocks to the recorder during transport.

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

button does not completely shut off mains power from the unit, but switches

” shows electrical power standby and “!” shows ON.

Page 4

FRONT VIEW

INDEX

STANDBY/ON

Front Panel Open Button

SP/LP/EP Button 墌pg. 26

AUDIO Button 墌pg. 23

Display – –:– – Button 墌pg. 27

Cassette Loading Slot

SYNCHRO

INDEX MARK Button 墌pg. 22

Stop/Eject

INDEX ERASE Button 墌pg. 22

SAT

S-VHS ET Button 墌pg. 29

DIGITAL TBC/NR Button 墌pg. 23

To access covered buttons/connectors, press the front panel open button so that the front panel opens.

Button 墌pg. 38

Button 墌pg. 12

Button 墌pg. 62

7/79

Button 墌pg. 20, 26

Timer

S-VIDEO/VIDEO/AUDIO Input Connectors

墌

TV/VCR Button 墌pg. 27

Counter Reset 0000 Button 墌pg. 27

Cancel Front Display Panel 墌pg. 6

Infrared Beam Receiving Window

Random Assemble Edit (R.A.EDIT) Button

墌

Random Assemble Edit IN/OUT Button 墌pg. 61

Random Assemble Edit START Button 墌pg. 61

Button 墌pg. 33, 35

pg. 51, 56, 58

Button 墌pg. 36

pg. 60

Page 5

INSIDE VIEW OF FRONT PANEL

PROG Button 墌pg. 32

DAILY Button 墌pg. 33, 35

Programme Check

WEEKLY Button 墌pg. 33, 35

VPS/PDC Button 墌pg. 33, 35

OK Button 墌pg. 13

SAT

G H I J K L M N

Indicator 墌pg. 38

S-VHS ET Indicator 墌pg. 29, 71 DIGITAL TBC/NR Indicator 墌pg. 23 INSERT Button 墌pg. 59 Time r Audio Dubbing (A.DUB) Button 墌pg. 57 JOG Dial 墌pg. 21 SHUTTLE Ring 墌pg. 21

Indicator 墌pg. 33, 35

Button 墌pg. 36

START +/– Buttons 墌pg. 34

STOP +/– Buttons 墌pg. 34

DATE +/– Buttons 墌pg. 34

PR +/– Buttons 墌pg. 26

Stop

S T U V W X Y

Button 墌pg. 20, 26

Rewind Play

Fast Forward Pa us e Record <<

button on the remote control 墌pg. 21, 22

Button 墌pg. 20, 21

Button 墌pg. 20

Button 墌pg. 20, 21

Button 墌pg. 21

Button 墌pg. 26

and 6 >> Buttons — same as w e

Page 6

REAR VIEW

INDEX (cont.)

Mains Power Cord 墌pg. 10

S OUT Connector 墌pg. 11

AV1 (L-1) IN/OUT Connector 墌pg. 10, 54, 64,

65, 66 J Terminal [JLIP (Joint Level Interface Protocol)

Connector] 墌pg. 63 SYNCHRO EDIT Connector 墌pg. 62

ANT. IN Connector 墌pg. 10

FRONT DISPLAY PANEL

B.E.S.T. Picture System Display 墌pg. 31

Audio Level Indicator 墌pg. 29 Programme Time Indicators 墌pg. 34

Symbolic Mode Indicators

STILL:

PLAY: FF/REW VARIABLE SEARCH:

AUDIO DUBBING:

AUDIO DUBBING PAUSE:

INSERT:

SLOW:

RECORD:

RECORD PAUSE:

Remote PAUSE Connector 墌pg. 51

R.A.EDIT Connector 墌pg. 60 AUDIO OUT (L/R) Connectors 墌pg. 67

AV2 (L-2) IN/DECODER Connector

pg. 17, 54, 64, 65, 66

墌

SAT CONTROL Connector 墌pg. 17

RF OUT Connector 墌pg. 10

“Timer” Indicator 墌pg. 33, 35

S-VHS Indicator 墌pg. 29, 71

Channel/Clock Display 墌pg. 15

Tape Speed Indicators 墌pg. 26

Audio Mode Indicator 墌pg. 23

Tape Remaining Time Indicator 墌pg. 27

“Cassette Loaded” Mark

VPS/PDC Indicator 墌pg. 33, 35

VCR Indicator 墌pg. 27

Counter/Remain Display

(The counter can display up to +/– “19:59:59”. If the playback or recording time exceeds this limit, the display starts to count from “0:00:00”.) Mode Display (L-1, L-2, F-1, S-1 or SAT*)

* When “L-2 SELECT” is set to “SAT” (墌pg. 53), “SAT” appears

instead of “L-2”.

INSERT PAUSE:

AV INSERT:

AV INSERT PAUSE:

Page 7

ON-SCREEN DISPLAY

When “O.S.D.” is set to “ON” (墌pg. 69), various operational indicators appear on the TV screen.

Operation Mode Indicators

Tape Speed SP/LP/EP

Tape Direction

Index MARK/ERASE Indicator 墌pg. 22

Counter Display

Tape Remaining Time Indicator 墌pg. 27

Audio Mode Display 墌pg. 23

Tape Position Indicator

The tape position indicator appears on the TV screen when you press

5 from the Stop mode

or perform an Index Search (

pg. 22). The position of

墌

“

q” in relation to “0”

(beginning) or “+” (end) shows you where you are on the tape.

3 or

Beginning End

NOTE:

Depending on the type of tape being used, the tape position indicator may not appear correctly.

Type of Broadcast 墌pg. 30

Current Day/Month/Year

Clock Display

Channel Position Number and Station Name/

Auxiliary Input Indicator (L-1, L-2, F-1, S-1 or SAT*)

* When “L-2 SELECT” is set to “SAT” (墌pg. 53), “SAT” appears

instead of “L-2”.

Timer Warning Display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you’re not in the Timer mode at that time. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press

“Cassette Loaded” Mark

& on the remote control.

Page 8

REMOTE CONTROL

LCD Panel 墌pg. 32

TV Button 墌pg. 40

VCR Button 墌pg. 39

AUDIO Button 墌pg. 23

(TV Muting) Button 墌pg. 40

LCD PROG Button 墌pg. 32

Number Keys 墌pg. 26, 32

DAILY Button 墌pg. 33, 35

VPS/PDC Button 墌pg. 33, 35

Counter Reset 0000 Button 墌pg. 27

Cancel Programme Check

PROG Button 墌pg. 32

START +/– Button 墌pg. 34

STOP +/– Button 墌pg. 34

Rewind

Play

Record

P Q

r t

Button 墌pg. 36

Button 墌pg. 20, 21

Button 墌pg. 20

Button 墌pg. 26

Button 墌pg. 12

Button 墌pg. 36

TV PR +/– Button 墌pg. 40 CABLE/SAT Button 墌pg. 41

STANDBY/ON

Display – –:– – Button 墌pg. 27

TV/VCR Button 墌pg. 27

30 SEC Button 墌pg. 22

Transmit Button 墌pg. 32

WEEKLY Button 墌pg. 33, 35

Timer

AUX Button 墌pg. 51

MENU Button 墌pg. 16

Auto Tracking

Button 墌pg. 33, 35

Button 墌pg. 12

Button 墌pg. 23

SP/LP/EP Button 墌pg. 26 OK Button 墌pg. 13

NAVIGATION Button 墌pg. 42

PR +/– Button 墌pg. 26

DATE +/– Button 墌pg. 34

Fast Forward

Stop

h i j

Button 墌pg. 20, 26

Pa us e

w e

Button 墌pg. 21

Button 墌pg. 21, 22

+/– Button 墌pg. 40

Button 墌pg. 20, 21

INDEX (cont.)

Buttons with a small dot on the left side of the name can also be used to operate your TV. (

墌

pg. 40)

Page 9

How To Use

The remote control can operate most of your video recorder’s functions, as well as basic functions of TV sets and satellite receivers of JVC and other brands. (

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is about 8 m.

pg. 40, 41)

墌

NOTES:

●

When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

●

If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

Remote Control LCD

The remote control can operate not only the video recorder but also some of your TV and satellite receiver’s functions. The LCD indicates which of these (VIDEO, TV or CABLE/SAT) the remote control can currently operate. When you first purchase the remote control, or after you have just replaced the batteries, VIDEO A (A code) is selected.

A To operate your video recorder, first press the

remote control to the Video mode. To switch the remote control’s A/B code, refer to page 39.

B To operate your TV, first press the TV button to set the remote

control to the TV mode. (

墌

pg. 40)

button to set the

VCR

C To operate your satellite receiver, first press the

to set the remote control to the satellite receiver mode. (

CABLE/SAT

墌

button

pg. 41)

NOTES:

Even if “TV” is displayed on the LCD, the following operations can be performed without switching the mode.

●

Basic operations for the recorder After an operation is completed, “TV” reappears on the LCD.

●

Express timer programming and S To perform a TV operation again, switch to TV mode first.

●

Accessing main menu To perform a TV operation again, switch to TV mode first.

HOWVIEW

timer programming operations

Page 10

Basic Connections

Aerial connector

INSTALLING YOUR NEW RECORDER

It’s essential that your video recorder be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

Back of TV

21-pin SCART cable (not provided)

Mains power cord

Back of recorder

21-pin SCART connector

(provided)

AV1 (L-1) IN/OUT

Mains outlet

RF cable

TV aerial cable

ANT. IN

RF OUT

Check the contents.

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 86.

Situate the recorder.

Place the recorder on a stable, horizontal surface.

Connect the recorder to TV.

The connection method you use depends on the type of TV you have.

RF Connection

8 To connect to a TV with NO AV input connectors . . .

Disconnect the TV aerial cable from the TV.

Connect the TV aerial cable to the ANT. IN connector on the rear panel of the recorder.

Connect the provided RF cable between the RF OUT connector on the rear panel of the recorder and the TV’s aerial connector.

AV C on nection

8 To connect to a TV with AV input connectors . . .

Connect the aerial, recorder and TV as per “RF Connection”.

Connect an optional 21-pin SCART cable between the AV1 (L-1) IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin SCART connector.

Make AV connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. With AV connection, you can enjoy stereo playback of video tapes if you are using a stereo TV.

NOTES:

●

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). If your TV’s 21-pin AV input connector (SCART) is compatible with the Y/C signal, set “L-1 OUTPUT” to “S-VIDEO” after the connection and the initial settings are completed ( high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

●

Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to the type of your TV’s SCART connector.

●

For switching the TV’s mode, refer to the instruction manual of your television.

●

To obtain high-quality S-VHS pictures, you can also use the S-VIDEO connection described on page 11.

墌

pg. 52). You can obtain

Connect the recorder to mains.

Plug the end of the mains power cord into a mains outlet.

After the connection is completed, perform “Auto Set Up” on page 12.

Page 11

S-VIDEO Connection

Back of TV

Aerial connector

Mains

power cord

AUDIO IN connectors

S-VIDEO IN connector

Mains outlet

S OUT

S-Video cable (provided)

Audio cable (not provided)

TV aerial cable

Back of recorder

8 To connect to a TV with S-VIDEO/AUDIO IN

connectors . . .

Connect the recorder to TV.

Connect the aerial, recorder and TV as per “RF Connection” (

Connect the recorder’s S OUT connector to the TV’s S-VIDEO IN connector.

Connect the recorder’s AUDIO OUT connectors to the TV’s AUDIO IN connectors.

Connect the recorder to mains.

Plug the end of the mains power cord into a mains outlet.

墌

pg. 10).

AUDIO OUT

RF cable (provided)

NOTES:

●

You can obtain high-quality S-VHS pictures.

●

With S-VIDEO connection, you cannot use the Preset Download function (

●

If your TV is not stereo-capable, use the recorder’s AUDIO OUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction. (

●

To operate the recorder with your TV using the S-VIDEO connection, set your TV to its AV mode.

●

For switching the TV’s mode, refer to the instruction manual of your television.

After the connection is completed, perform “Auto Set Up” on page 12.

墌

pg. 14).

墌

pg. 67)

Page 12

Auto Set Up

Auto Channel Set/Auto Clock Set/ Auto Guide Program Number Set

After the pressed for the first time to power on the recorder selecting your country*, the Auto Set Up function sets the tuner channels, clock** and Guide Program numbers automatically.

* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also

**If you live in Hungary (MAGYARORSZÁG), Czech Republic (

1 button on the recorder or remote control is

need to select your language.

REPUBLIKA), Poland (POLSKA), Russia ( countries in Eastern Europe (OTHER EASTERN EUROPE), set the clock manually.

РОССИЯ

, by simply

) or other

ESKÁ

INITIAL SETTINGS

Before starting, make sure of the following:

● The TV aerial cable should be connected to the recorder.

● The recorder’s mains power cord should be connected to a

mains outlet.

● If you want to use the on-screen display, the TV should be set to its AV mode (with AV or S-VIDEO connection

pg. 10, 11) or UHF channel 36 (with RF connection

墌

pg. 10).

墌

Turn on the recorder.

Press 1 on the recorder or remote control. The Country Set display appears on the front display panel and/or on the TV screen.

NOTE:

If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, perform “Video Channel Set” on page 78.

International Telephone Country Code

ÖSTERREICH

BELGIUM

ESKÁ REPUBLIKA DAN MARK DEUTSCHLAND ESPAÑA GREECE ITALIA MAGYARORSZÁG NEDERLAND NORGE

: : : : : : : : : :

POLSKA

PORTUGAL

SUISSE

SUOMI

SVERIGE

РОССИЯ

39 36

OTHER WESTERN EUROPE

OTHER EASTERN EUROPE

Select your country.

On the front display panel

Press

to select your international telephone country

code of your country referring to the chart in the left column.

(Example) DEUTSCHLAND (49) is selected.

On the on-screen display

Press

to move the

highlight bar (pointer) to your country’s name.

NOTES:

● If you have selected BELGIUM (32) or SUISSE (41), go to step3.

● If you have selected MAGYARORSZÁG (36), REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER

351

358

– –

EASTERN EUROPE (EE), press OK. The Clock Set screen appears. Set the clock manually (

● If you have selected any other country name (code), press OK and go to step 4.

墌

ESKÁ

pg. 80), then go to step 4.

Page 13

Select the language.

Beginning End

Press OK. The Language Set display appears on the front display panel and/or on the TV screen.

On the front display panel

Press

Language Code

ENGLISH DEUTSCH FRANCAIS ITALIANO CASTELLANO NEDERLANDS SVENSKA

(Example) DEUTSCH (02) is selected for SUISSE (41).

to select your language code.

NORSK

: : : : : : :

International telephone country code

02 03 04 05 06 07

SUOMI DAN SK POLSKI

CEc

MAGYAR

ЯЗЫК

TINA

Language code

On the on-screen display

Press

to move the

highlight bar (pointer) to the language of your choice.

● If you are using the on-screen display, the AUTO SET screen will appear. As Auto Set Up progresses, the “ mark on the TV screen moves from left to right. When the Auto Set Up is completed, “SCAN COMPLETED” appears for about 5 seconds, then the normal screen appears.

● If you have connected the recorder to your TV via the AV connection ( perform Preset Download ( Up.

墌

q”

pg. 10), the recorder will automatically

pg. 14) instead of the Auto Set

墌

ATT E NT I O N

Once you have performed Auto Set Up, even if the recorder’s memory backup has expired, all the stored stations and their Guide Program numbers remain in the recorder’s memory and the recorder will not perform Auto Set Up again. You only need to set the clock. ( If you have moved to a different area, perform each setting as required.

● Video channel setting (for RF connection users)

● Tuner setting

● Clock setting

If a new station starts broadcasting in your area, perform tuner setting ( setting (

墌

pg. 72

墌

pg. 80

墌

pg. 72) and, if necessary, video channel

墌

pg. 78).

墌

pg. 80)

墌

pg. 78

Perform Auto Set Up.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press

to select “Auto” and press OK or e.

On the on-screen display

Press

to move the

highlight bar (pointer) to “AUTO SET” and press OK or

“Auto” blinks on the front display panel; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 15.

NOTES:

● In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again from step 1.

● Auto Clock Set may not function properly depending on the reception condition.

● If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (

pg. 75, “INFORMATION”).

墌

1 or

while Auto

Page 14

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide

INITIAL SETTINGS (cont.)

If you have connected the recorder to your TV via the AV connection ( Preset Download instead of the Auto Set Up in step 4 on page 13. After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 12 before continuing.

pg. 10), the recorder will automatically perform

墌

Program Number Set

ATTE N TI O N

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press

On the on-screen display

Press highlight bar (pointer) to “T-V LINK” and press OK or

● If you are using the on-screen

● If you press any button on the

to select “CH – –” and press OK or e.

to move the

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 15.

display, the T-V LINK screen will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

recorder or remote control while downloading is in progress, it will be interrupted.

NOTES:

● For details, refer to the instruction manual of your TV.

● In the area where no TV station transmits a PDC (Programme

Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

● If there is a power cut, or if you press downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

● Auto Clock Set may not function properly depending on the reception condition.

● On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, downloaded stations may differ from those of your TV (

pg. 76).

墌

f, + and I (space). Some names of

1 or

while

Set the video channel.

Set the video channel to off manually. (墌pg. 78)

Page 15

Results of Auto Set Up/Preset Download appear on the front display panel

If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed.

Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 74 – 77.

If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is displayed.

A Turn on the TV and select its video channel or AV mode, then make sure that all necessary

stations have been stored in the recorder’s memory by using the PR button(s).

● If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 74 – 77.

B Perform “Clock Set” on page 80.

If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.

Make sure the cables are connected properly and turn off the recorder’s power once, then turn the recorder’s power back on again. The Country Set display appears on the front display panel and/or on the TV screen; perform “Auto Set Up” on page 12 or “Preset Download” on page 14 again.

pg. 77) have also been stored in the recorder’s memory, the station name

墌

pg. 77) have also been stored in the recorder’s memory, the station name

墌

IMPORTANT

● To check if the Guide Program numbers have been set correctly, perform the S

● In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work

properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S system, the recorder will record a TV programme of a different station. When programming the timer using the S system, be sure to check the desired channel is selected correctly (

● Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture (

pg. 75, “Delete A Channel”).

墌

HOWVIEW

pg. 32, “S

Timer Programming (墌pg. 32).

HOWVIEW

Timer Programming”).

HOWVIEW HOWVIEW

INFORMATION

Language for the on-screen display

Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made in step 2 on page 12 (unless you have selected BELGIUM or SUISSE), as shown below.

SUOMI PORTUGAL DEUTSCHLAND POLSKA NORGE SVERIGE

If you want to change the language setting manually, see “Language” on page 16.

Just Clock

Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON” (

pg. 80, “Just Clock”).

墌

SUOMI DANMARK

]

ENGLISH ÖSTERREICH

]

DEUTSCH

]

POLSKI ITALIA

]

NORSK MAGYARORSZÁG]MAGYAR OTHER EASTERN EUROPE]ENGLISH

]

SVENSKA ESPAÑA

]

ESKÁ REPUBLIKA

DANSK NEDERLAND

]

DEUTSCH GREECE

]

CEc

TINA РОССИЯ

]

ITALIANO OTHER WESTERN EUROPE]ENGLISH

]

CASTELLANO

]

] ] ]

NEDERLANDS ENGLISH

ЯЗЫК

Page 16

Language

Turn on the TV and select the video channel (or AV mode).

INITIAL SETTINGS (cont.)

This recorder offers you the choice to view on-screen messages in 14 different languages. Though Auto Set Up selects the language automatically (墌pg. 15), you can change the language setting manually as required.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press

Press rt to move the highlight bar (pointer) to your country’s name, then press OK or

Access the Country Set screen.

Select your country.

Select the language.

Press highlight bar (pointer) to the language of your choice.

● You do not have to press OK;

Press

to move the

pressing OK enters AUTO SET/ T-V LINK screen.

Return to the normal screen.

Page 17

SAT CONTROL SET

Satellite Receiver Control Setting

The following procedure is required if you receive satellite channels through a satellite receiver. Approximately 20 seconds before the S programming ( (

pg. 34) starts, the recorder sets its input mode to “L-2”

墌

and automatically switches the satellite receiver’s channels using the provided Satellite Controller.

pg. 32) or Express timer programming

墌

HOWVIEW

timer

Your recorder

Satellite receiver

21-pin SCART cable (not provided)

Satellite Controller

Satellite receiver

Satellite Controller (suggested locations)

Transmitter

Installing Satellite Controller

Situate the Satellite Controller.

Place the Satellite Controller so that the path between its transmitter and the satellite receiver’s remote sensor is unobstructed.

Attach the Satellite Controller.

Fix securely using the adhesive strip attached on the back of the Satellite Controller.

Make connections.

Be sure to connect the recorder’s AV2 (L-2) IN/DECODER connector to the satellite receiver’s 21-pin SCART connector.

NOTE:

When connecting your satellite receiver, refer to its instruction manual.

Connect the Satellite Controller to recorder.

Connect the Satellite Controller to the SAT CONTROL connector on the rear panel.

AV2 (L-2) IN/DECODER

Back of recorder

SAT CONTROL

Page 18

SAT CONTROL SET (cont.)

Access the Initial Set screen.

Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or

Access the Sat Control Set screen.

Press rt to move the highlight bar (pointer) to “SAT CONTROL SET”, then press OK or

Press the appropriate

to enter the brand code

keys

from the list on page 19, then press OK.

● If the brand code you entered is invalid, the code field will be reset. Enter the correct brand code again.

● If the recorder is in playback or recording mode, you cannot set the brand code.

Enter the satellite receiver’s brand.

number

Setting satellite receiver's brand and channel

After installation, set the satellite receiver’s brand and channel correctly; otherwise, the Satellite Controller cannot work correctly.

Turn on the TV and select the video channel (or AV mode).

Turn on the satellite receiver.

Turn on the satellite receiver’s power.

Access the Main Menu screen on the

recorder.

Press

Select the satellite receiver’s channel for

testing.

Press the appropriate

to enter one of the

keys

channel positions on the satellite receiver, then press

● You can select the channel position between 1 to 999.

● After pressing OK, the recorder enters the Test mode.

number

Page 19

SAT CONTROL SET (cont.) T-V LINK

Check the result of the test.

If the satellite receiver’s channel number has been changed to the same one as you set in step 6 ...

Press bar (pointer) to “CHANGED TO ...”, then press OK or finish the Sat Control Set mode.

If the satellite receiver’s channel number has not been changed correctly ...

Press CHANGED”, then press OK or procedure again from step 5.

BRAND NAME CODE

JVC AMSTRAD CANAL SATELLITE CANAL + D-BOX ECHOSTAR ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN ITT NOKIA JERROLD KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASONI C PHILIPS RFT SAGEM SALORA SIEMENS SKYMASTER TPS TRIAX WISI

to move the highlight

to move the highlight bar (pointer) to “NOT

. Then perform the

73 60, 61, 62, 63, 92 81 81 85 78, 79, 80 82 68 89 88 64, 65 64, 78 68 75 70, 71 68 93 70 87 65, 67, 74, 86, 92 74 66, 84 69 83 68 64 69 83 91 64

T-V Link Functions

When you connect the recorder to your TV via a fully-wired 21-pin SCART cable ( available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

NexTView Link

You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder. For details, refer to the instruction manual of your TV.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you play a tape. For details, refer to the instruction manual of your TV.

VCR Auto Standby

You can use your TV’s remote control to turn off the recorder. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON” (

墌

pg. 10), the following functions are

墌

pg. 69).

NOTES:

● The Satellite Controller may not work with all types of satellite receiver.

● For some satellite receivers, you need to set its channel input mode to 2-digit.

● If your satellite receiver has more than two channel modes, be sure to set to “All Channel Mode”. For details, refer to the instruction manual of the satellite receiver.

● When selecting the satellite receiver’s channel ( signals from the remote control may interfere with signals transmitted from the Satellite Controller. In this case, move the remote control as close to the recorder’s infrared beam receiving window as possible.

step 6),

墌

Page 20

Basic Playback

Turn on the TV and select the video channel (or AV mode).

PLAYBACK

Load a cassette.

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the recorder.

● Do not apply too much pressure when inserting.

● The recorder’s power comes on automatically and the counter

is reset to “0:00:00”.

● While “– – – –” is blinking on the front display panel, the tape will run for a few seconds to search for the tape number.

● If the record safety tab has been removed, playback begins automatically.

Find the programme start point.

If the tape is advanced past the start point, press 3. To go forward, press 5.

Start playback.

Press 4. “BEST” appears blinking in the recorder’s front display panel during automatic tracking. (

Stop playback.

Press 8, or

to remove the cassette.

on the recorder’s front panel. Then press

墌

pg. 31)

Clean the video heads using a dry cleaning cassette — TCL-2UX — when:

● Rough, poor picture appears while a tape is played back.

● The picture is unclear or no picture appears.

● “USE CLEANING CASSETTE” appears on the screen (only

with “O.S.D.” set to “ON” (

墌

pg. 69)).

Usable cassettes

● Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

● This video recorder can record on regular VHS and Super VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes*, both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes.

* By using the S-VHS ET function, it is possible to record and

play back with S-VHS picture quality on VHS cassettes with this recorder.

Page 21

Playback Features

NOTES:

● Refer to the

SHUTTLE

illustration on the right as you read the following procedures.

● Reverse playback is possible only with a tape recorded in SP mode.

ATTE N TI O N

● The operations by

● Picture may not appear during high-speed search with an

● Noise may appear or the picture may appear distorted with

● In the high-speed search, still, slow motion or

● When normal playback resumes from search (including

Variable Speed Search

During playback or still, turn the right for forward variable-speed search, or to the left for reverse variable-speed search (refer to the illustration above).

ring

TimeScan. (

LP/EP-recorded tape.

an EP-recorded tape during still, slow motion, frame-by-frame playback or variable speed search.

frame-by-frame playback mode, the picture will be distorted, and there will be a loss of colour.

TimeScan), still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

墌

JOG

pg. 24)

SHUTTLE

dial/

ring do not include

SHUTTLE

ring to the

Still Picture/Frame-By-Frame Playback

Pause during playback.

Press 9.

● If there is vertical jitter, use the PR buttons to correct the picture.

● During still picture, the sound from the previous 3 seconds (approx.) will be played back repeatedly (provided there was at least 6 seconds of normal playback prior to engaging the pause mode).

● “TIME SCAN AUDIO” must be set to “ON”, or you cannot hear the sound during still picture. (

Activate frame-by-frame playback.

Tur n t h e playback, or to the left for reverse frame-by-frame playback.

dial to the right for forward frame-by-frame

JOG

墌

pg. 71)

Press 9.

Press w or e.

Slow Motion

During playback or still, turn the right for forward slow motion, or to the left for reverse slow motion (refer to the illustration on the left).

SHUTTLE

During still picture, press and hold 9 for 2 seconds, then release. Press picture.

and release again to return to still

During still picture, press and hold w or e. Release to return to still picture.

NOTES:

● For Time Jog, see page 25.

● Manual tracking is possible during slow motion playback.

(

pg. 23)

墌

ring to the

High-Speed (Turbo) Search

During playback or still, turn the way to the right for forward high-speed search, or to the left for reverse high-speed search. Releasing ring resumes still picture playback.

SHUTTLE

During playback or still, press 5 for forward high-speed search, or

for reverse high-speed search.

NOTE:

For short searches, press and hold 5 or 3 for over 2 seconds during playback or still picture. When released, normal playback resumes.

ring all the

SHUTTLE

NOTE:

Variable speed search with TimeScan (墌pg. 24) can be used by pressing the remote control’s

w or e button.

To resume normal playback, press 4.

Page 22

DIGITAL TBC/NR indicator

PLAYBACK (cont.)

Index Search

Your recorder automatically marks index codes at the beginning of each recording. Additional index codes can be added manually during playback. (See below.) This function gives you quick access to any one of 9 index codes in either direction.

NOTE:

Before starting, make sure the recorder is in the Stop mode.

Activate Index Search.

Press w or e (2 or 6). “2 1” or “6 1” is displayed on the TV screen and search begins in the corresponding direction.

● To access index codes 2 through 9, press until the correct index number is displayed.

Example:

To locate the beginning of B from the current position, press twice. To locate the beginning of D from the current position, press once.

Current position

w or e repeatedly

Skip Search

During playback, press unwanted sections. Each press initiates a 30-second period of fast-motion playback. Normal playback resumes automatically.

To resume normal playback during a Skip Search, press

1 to 4 times to skip over

30 SEC

Index number

● When the specified index code is located, playback begins automatically.

Manual Index Mark/Erase

To mark an index code ...

... during playback press

● The recorder will mark an index code at that location.

● If “O.S.D.” is set to “ON” (

screen while an index code is being marked.

To erase an index code ...

... during playback or still press

● The recorder will fast-forward to the nearest index code and erase it. Playback continues after the index code is erased.

● If “O.S.D.” is set to “ON” ( screen while an index code is being erased.

INDEX MARK

墌

NOTES:

● Video Navigation ( index code (VISS signal) is marked or erased manually near a start point of recorded programme.

● During timer-recording you cannot mark an index code manually.

pg. 42) may not work properly when an

墌

on the recorder.

pg. 69), “MARK” blinks on the

INDEX ERASE

pg. 69), “ERASE” blinks on the

on the recorder.

Page 23

Next Function Memory

The Next Function Memory “tells” the recorder what to do after rewinding. Before continuing, make sure the recorder is in the Stop mode.

For Automatic Start Of Playback

Press For Automatic Power Off

Press 3, then press 1 within 2 seconds. For Automatic Timer Standby

Press 3, then press # (

, then press 4 within 2 seconds.

TIMER

) within 2 seconds.

Digital TBC/NR

Your recorder is equipped with the Digital TBC (Time Base Corrector) that removes jitter from fluctuating video signals to deliver a stable picture even with old tapes and rental cassettes. The on/off of Digital 3-DNR (Noise Reduction) which cuts noise and enables clear picture reproduction is also linked to this function. * The default setting is on. We recommend that you use Digital TBC/NR when... ... playing back a tape recorded on a camcorder. ... playing back a tape repeatedly used. ... using this video recorder as the source player for editing.

Activate Digital TBC/NR.

Press

DIGITAL TBC/NR

indicator lights up.

● To turn off Digital TBC/NR, press that the indicator goes off.

so that the DIGITAL TBC/NR

DIGITAL TBC/NR

again so

NOTES:

● If you play back a tape recorded under poor TV reception condition, the picture may become more stable with Digital TBC/NR set to off.

● When Digital TBC/NR is set to on, if you play back a tape where certain types of signals are recorded (using a PC or some character generators), the playback picture may be distorted. If this is the case, turn off Digital TBC/NR.

● When playing back a MESECAM tape, Digital TBC/NR does not function even though the DIGITAL TBC/NR indicator is lit.

Repeat Playback

Your recorder can automatically play back the whole tape 100 times repeatedly.

Start playback.

Press 4.

Activate Repeat Playback.

Press 4 and hold for over 5 seconds, then release.

● The Play indicator ( slowly.

● After playing back a tape 100 times, the recorder stops automatically.

Stop Repeat Playback.

Press 8 at any time.

● Pressing

4, 3, 5 or 9 also stops Repeat Playback.

u) on the front display panel blinks

Manual Tracking

Your recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the PR buttons.

Override automatic tracking.

Press p on the remote control.

Adjust the tracking manually.

Press PR + or –.

Return to automatic tracking.

Press p on the remote control.

NOTE:

When a new tape is inserted, the recorder enters the automatic tracking mode automatically.

Soundtrack Selection

Your recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing

Recorder’s Front

Display Panel

a + s

NORM NORM

a + s + NORM

NOTES:

● “

a + s” should normally be selected. In this mode, Hi-Fi

stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio.

● For instructions on recording stereo and bilingual programmes, refer to page 30.

● “O.S.D.” must be set to “ON” or the on-screen displays will not appear (

changes the soundtrack as follows:

AUDIO

TRACK

On-Screen

Display

HI FI

j h R

pg. 69).

墌

HI FI

NORM

h R

USE

For Hi-Fi stereo tapes

For main audio of Bilingual tapes

For sub audio of Bilingual tapes

For audio-dubbed tapes

NOTE:

Repeat playback is not possible with a cassette recorded in EP mode.

Page 24

TimeScan

PLAYBACK (cont.)

This recorder is equipped with the TimeScan function that allows noise free pictures on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during TimeScan ( programme in search mode while listening to the audio.

pg. 25). TimeScan also allows you to view a

墌

NOTES:

● “TIME SCAN AUDIO” must be set to “ON”, or you cannot hear the sound during TimeScan. (

● The audio will not synchronize with the video in TimeScan modes.

● During 1.5x speed TimeScan the audio playback speed will also be 1.5 times normal, so dialog will sound fast-talking.

● During still picture, the sound from the previous 3 seconds (approx.) will be played back repeatedly (provided there was at least 6 seconds of normal playback prior to engaging the pause mode).

● During TimeScan some of the audio information will not be played so that the audio can keep up with the video.

Audio signal during TimeScan

Playback tape

Sound of 1, 3 and 5 is heard. Sound of 2 and 4 is not heard. Output audio signal is normal (monaural) sound.

墌

pg. 71)

Activate Variable Speed Search.

During playback, press w or e.

● The more times you press, the faster the playback picture moves.

● To decrease speed, press the button for the opposite direction. (Refer to the chart on page 25 for playback speeds.)

To resume normal playback, press 4.

If the picture jitters vertically during still picture or variable speed search with a MESECAM tape:

A Press B Press

or – so that the vibration stops.

PR +

Page 25

TimeScan

Names of special-effects playback

Speed SP

Speed LP

Speed EP

Audio output

* Still mode cannot be engaged using the remote control’s w or e button. Still mode can be engaged by pressing the 9 button. **Smooth slow motion delivering an uninterrupted moving image without distortion.

● ±1/6x and ±1/18x search of EP recordings are not Time Jog.

● If the picture jitters vertically, noise appears or the upper or lower part of the picture is distorded at -1/2x, -1/3x, 1/3x, 1/2x or 1.5x

normal speed, use

● Noise may appear during TimeScan search, depending on the search speed.

● When noise appears or the upper or lower part of the picture is distorted during TimeScan, press

or – button.

● The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (The display may be distorted.)

● To resume normal playback, press

● Picture and audio may become distorted when the recording speed changes. When this happens, resume normal playback once,

and then try using TimeScan again.

● The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with LP/EP recordings.)

● Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP/EP recordings, or depending on the tape being used.

● Picture may appear distorted in comparison to normal playback.

● When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture may

jitter vertically momentarily depending on the type of TV being used.

● During TimeScan there will be a time lag between the video and the audio and noise may appear in the audio signal.

● TimeScan sound quality will differ in comparison to normal playback.

● When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 1.5x or 2x

normal speed, the audio playback may be faster than normal.

● Depending on the type of tape contents, the sound may not be clear during forward slow-motion playback.

● Time Jog cannot be activated by pressing

● When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.

● Picture will be monochrome with an LP-recorded MESECAM tape during TimeScan.

● Time Jog does not work with NTSC playback.

● When playing back an NTSC tape, the speeds differ from those listed above and are not shown on the TV screen.

● TimeScan at -1/2x, 1/2x and 1.5x normal speed are not possible with a MESECAM tape.

● The operations by

Search Play

-9x -7x -5x -3x -1x -1/2x -1/3x 0 1/3x 1/2x 1x 1.5x 2x 3x 5x 7x 9x

— -7x — -3x — -1/2x — 0 — 1/2x 1x 1.5x 2x — 5x — 9x

— -7x — -3x — -1/6x -1/18x 0 1/18x 1/6x 1x — 2x — 5x — 9x

Audio is output.

or – to correct the picture.

PR +

dial/

JOG

SHUTTLE

Reverse Forward

Slow-Motion

(Time Jog**)

Audio is not

output.

9 for longer than 2 seconds.

ring do not include TimeScan. Noise will appear on the screen and audio will not be output.

Audio is

output.

*Still

Slow-Motion

(Time Jog**)

Audio is

output.

Play Search

Audio is output.

p and adjust tracking with

PR +

If you do not want to hear TimeScan audio, set “TIME SCAN AUDIO” to “OFF”. (墌pg. 71)

Page 26

Basic Recording

Turn on the TV and select the video channel (or AV mode).

RECORDING

Load a cassette.

Insert a cassette with the record safety tab intact.

● The recorder’s power comes on automatically and the counter is reset to “0:00:00”.

● While “– – – –” is blinking on the front display panel, the tape will run for a few seconds to search for the tape number.

Choose a programme.

Press you wish to record.

Press the recorder’s front display panel to confirm the selected tape speed.

● In EP mode, the recording time is extended three times.

● If you record a programme in EP mode on this recorder, it is

recommended to play back the EP-recorded tape on this recorder.

● It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”.

Press and hold 7 and press 4 on the remote control, or press

or the

PR +/–

number keys

Set the tape speed.

SP/LP/EP

(p). Check the SP/LP/EP indicator on

(

pg. 71

墌

Start recording.

on the recorder.

to select the channel

)

Recording Resume Function

If there is a power outage during recording, Instant Timer Recording ( recording will resume automatically when power is restored to the recorder unless the recorder’s memory backup has expired.

pg. 27) or timer recording (墌pg. 32, 34), the

墌

B.E.S.T. takes place at the beginning of both the first SP and the first LP (or EP) recording after inserting the cassette. (

pg. 31)

墌

If “DIRECT REC” is set to “ON”, the programme that appears on the TV screen will be recorded (

Pause/Resume recording.

Press 9. Press 4 to resume recording.

Stop recording.

Press 8, or remove the cassette.

on the recorder. Then press

墌

pg. 69).

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape.

Record safety tab

Page 27

Recording Features

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.

Start recording.

Press 7 on the recorder.

Engage the ITR mode.

Press 7 again. “o” blinks and “0:30” appears on the front display panel.

Set the recording duration.

If you want to record for more than 30 minutes, press 7 to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the 7 button on the recorder’s front panel.

Elapsed Recording Time Indication

Set the counter display.

Press – –:– – until a counter reading appears on the front display panel.

Record One Programme While Watching Another

If your recorder is connected to the TV via the AV connection, press and the TV broadcast being recorded disappear. Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.

● The programme selected with the TV’s channel controls appears on the TV screen, while the one selected with the recorder’s PR buttons is recorded on the tape.

● If a decoder is connected to the recorder ( select a scrambled channel as well with the TV channel controls.

TV/VCR

. The recorder’s VCR indicator

pg. 66), you can

墌

Reset the counter.

Press

● The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs. You can check the exact time of a recording or playback.

before starting recording or playback.

0000

Tape Remaining Time

Press – –:– – until the time remaining on the tape appears.

● The front display panel shows the tape remaining time with “

y” displayed.

● By pressing the – –:– – button, you can change the display to show the counter reading, channel position*, clock time or tape remaining time.

* Channel position is not displayed during playback.

NOTE:

Depending on the type of tape being used, the tape remaining time reading may not appear right away, or is not correct. “– –:– –” may sometimes appear, or the display may blink on occasion.

Page 28

RECORDING (cont.)

S-VHS ET indicator

Retake

You can cut out unnecessary parts of a TV programme while you are recording it.

End of programme Beginning of programme

Programme Programme

Engage the Record-Pause mode.

Press 9 during recording.

Locate the start point.

Tur n t h e or you want to resume recording.

● Your recorder returns to the Record-Pause mode.

Press 4 when you wish to resume recording.

JOG

) and release it when you reach the point where

Resume recording.

Unnecessary

part

Recorded part

Go back to end of programme to cut out unnecessary part

dial to the left or right (or hold down 3

NOTES:

● Retake function does not work during Direct Rec (

69).

● Noise may appear when Retake function is used at the part that is recorded in EP mode.

Unnecessary

part

墌

pg. 19,

Page 29

Super VHS ET (S-VHS ET) — Recording on VHS cassettes with

S-VHS quality

You can record in SP mode on VHS cassettes with S-VHS picture quality. Tapes recorded using this function can be played back on a recorder equipped with the S-VHS ET function.

● You can activate the S-VHS ET function only before you start recording on a VHS cassette.

● Before recording, make sure that “B.E.S.T.” is set to “ON”. (

pg. 69)

墌

Engage the S-VHS ET mode.

Press

S-VHS ET

on the recorder’s front panel lights up.

● The S-VHS indicator lights up on the front display panel.

● To disengage the S-VHS ET mode, press

ET indicator goes off.

NOTES:

● You cannot activate the S-VHS ET function ... ... while recording is in progress. ... while timer-recording or Instant Timer Recording (

pg. 27) is in progress.

墌

... while B.E.S.T. (

● The S-VHS ET function does not work ... ... with S-VHS cassettes. ... with recordings in LP/EP mode.

● To keep the highest quality recording and playback pictures over a long period of time, S-VHS recording on S-VHS cassettes is recommended.

● Use of high grade tapes is recommended for S-VHS ET recordings. On some tapes, picture quality will not improve even if the S-VHS ET function is used. Check the recording quality before you start important recordings.

● You can play back a tape recorded using the S-VHS ET function on most of S-VHS recorders and of VHS recorders equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice some recorders are not compatible with the S-VHS ET function.)

● While playing back a tape recorded using the S-VHS ET function on some recorders, noise may appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)

● In the high-speed search, still, slow-motion or frame-by-frame playback modes ( are performed frequently on a tape recorded using the S-VHS ET function, the tape may be damaged and the picture may be deteriorated.

on the recorder. The S-VHS ET indicator

S-VHS ET

pg. 31) is in progress.

墌

pg. 21), noise may appear. If these modes

墌

. The S-VHS

Audio Recording Level Control

Your recorder allows manual adjustment of the audio recording level.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “REC LEVEL CTL”, then press

Press

● Press move the on-screen’s audio levels by one division on the scale. To move the audio levels faster, press and hold

● Adjust the recording level while watching the audio level indicator on the recorder’s front display panel. Set the level so that maximum volume causes the indicator to vary between 0dB to 4dB.

Press

NOTES:

● Noise will increase if the recording level is too low, while distortion will increase if the level is too high.

● When you finished audio recording, be sure to set the level control back to its centre position.

Access the Recording Level Control screen.

Adjust the audio recording level.

or t.

r or t briefly 5 times to

r or t.

Return to the normal screen.

Page 30

RECORDING (cont.)

Receiving Stereo and Bilingual Programmes

Your recorder is equipped with a Sound-Multiplex decoder (A2) and a Digital stereo sound decoder (NICAM) making reception of stereo and bilingual broadcasts possible. When the channel is changed, the type of broadcast being received will be displayed on the TV screen for a few seconds.

Type of Broadcast Being Received

A2 Stereo A2 Bilingual Regular Monaural NICAM Stereo NICAM Bilingual NICAM Monaural

● To listen to a stereo programme, press “

s” appear on the front display panel or “HIFI L jhR”

appears on the TV screen.

● To listen to a bilingual programme, press “

s” appears on the front display panel, or “HIFI L j” or

“HIFI

h R” appears on the TV screen (as required).

● To listen to the standard (Regular Monaural) audio while receiving a NICAM broadcast, press appears on the front display panel or the TV screen.

On-screen Display

ST BIL. (none) ST NICAM BIL. NICAM NICAM

AUDIO

until “NORM”

AUDIO

until “

a” and

a” or

NOTE:

“O.S.D.” must be set to “ON” or the on-screen displays will not appear (

To Record Stereo and Bilingual Programmes (A2)

Stereo programmes are automatically recorded in stereo on the Hi-Fi audio track (with the normal audio track recording mixed L and R channel sound).

● Bilingual programmes are automatically recorded in bilingual on the Hi-Fi audio track. The main soundtrack will be recorded on the normal audio track.

墌

pg. 69).

To Record NICAM Stereo and Bilingual Programmes

The NICAM audio programme will be recorded on the Hi-Fi audio track, and the standard audio programme will be recorded on the normal audio track.

NOTES:

● If the quality of stereo sound being received is poor, the broadcast will be received in monaural with better quality.

● Before playing back a programme recorded in stereo, or a bilingual programme, refer to “Soundtrack Selection” on page 23.

Page 31

B.E.S.T. Picture System

The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible playback and recording pictures. You can set “B.E.S.T.” to “ON” or “OFF” to your preference (

pg. 69).

墌

Recording

The recorder assesses the quality of the tape once you initiate recording.

DURING B.E.S.T.

B.E.S.T. COMPLETE

Playback

The recorder assesses the quality of the tape once you initiate playback.

● The recorder adjusts the playback picture quality based on the quality of the tape in use.

● B.E.S.T. is active during automatic tracking. “BEST” appears blinking on the recorder’s front display panel.

NOTES:

● When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

● When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference (

● “BEST” only appears at the beginning of automatic tracking. Even though it doesn’t appear after that, the B.E.S.T. function is operative.

墌

pg. 69).

● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.

NOTES:

● The B.E.S.T. system works for both SP and LP (or EP) modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

● The B.E.S.T. system does not work while Automatic Satellite Programme Recording is in progress (

● In the case of timer recordings, the B.E.S.T. system works before recording is initiated.

● Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re-performed.

● Pressing the recorder’s does not start Instant Timer Recording (

7 button while “BEST” is displayed

墌

pg. 38).

pg. 27).

墌

ATT E NT I O N

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after and

4 on the remote control are pressed, or 7 on the

recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps: A Press and hold

Pause mode.

● The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re-enters Record Pause mode.

B Press If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” (

4 to start recording.

9 and press 7 to engage the Record

pg. 69).

墌

Page 32

TIMER RECORDING

HOWVIEW

Timer

Programming

Before performing the S Programming:

● Make sure that the recorder’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The recorder

will come on automatically.

● Turn on the TV and select the video channel (or AV mode).

LCD panel

HOWVIEW

Tim e r

You can use the on-screen display to enter the S number.

Access the S

Press

The front display panel looks like this:

Press the enter the S of a programme you wish to record. Then press OK.

● If you make a mistake, press and input the correct number.

PROG

Enter the S

number keys

HOWVIEW

number

screen.

number.

HOWVIEW

With the S simplified because each TV programme has a corresponding code number which your recorder is able to recognize. You can use the remote control with LCD panel to enter the S

HOWVIEW

Press

The LCD panel looks like this:

Press the a programme you wish to record. Then press .

● If you make a mistake, press The S

HOWVIEW

number.

Access the S

LCD PROG

Enter the S

number keys

HOWVIEW

system, timer programming is greatly

HOWVIEW

to enter the S

number you enter appears on the LCD panel:

display.

number.

HOWVIEW

& and input the correct number.

number of

The S

HOWVIEW

panel with only a 4-digit number:

The S

HOWVIEW

screen appears (if you’re just starting out, “P1” appears).

The front display panel shows the programme start time. Pressing

" changes the display to the programme stop time, then the

date and channel position.

IMPORTANT

Make sure the channel position number you wish to record is displayed; if not, see “S and set the Guide Program number correctly.

number you enter appears on the front display

Access the S

Program

HOWVIEW

Program screen.

System Setup” on page 79

Then go to step 3 in the right column.

● If the number you entered is invalid, “ERROR” appears on the TV screen and “Err” appears on the front display panel. Press

& and input a valid S

● If the “GUIDE PROG SET” screen appears, see “ATTENTION” on page 33.

HOWVIEW

number.

Page 33

Set the tape speed.

Press

SP/LP/EP

● It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”.

Press

VPS/PDC

● If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC” is lit on the front display panel, VPS/PDC is set to ON.

● If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC” is not lit on the front display panel, VPS/PDC is set to OFF.

“VPS/PDC Recording” on page 35.

墌

Press

PROG

on the TV screen for about 5 seconds, then the normal screen appears. If “PROGRAM OVERLAPPED” appears on the TV screen and “Err” on the front display panel, see page 37.

● Repeat steps 1 – 6 for each additional programme.

Press # ( and “

indicator on the recorder’s front panel also lights up.

● To disengage the timer mode, press

(p).

(

墌

pg. 71

)

Set the VPS/PDC mode.

to select “ON” or “OFF”.

Return to the normal screen.

or OK. “PROGRAM COMPLETED” appears

Engage the recorder’s timer mode.

). The recorder turns off automatically

TIMER

” appears on the front display panel. The #

# (

TIMER

) again.

NOTES:

● To Change The Stop Time . . . . . . press anticipated programme schedule delays.

● To Timer-Record Weekly Or Daily Serials . . . . . . in step 3, press serials or Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.

● You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, “PROGRAM FULL” appears on the TV screen and “FULL” appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (

● It is not possible to timer-record a TV programme with a S

Satellite Receiver Users

To timer-record a satellite broadcast using the S system:

A Perform “Satellite Receiver Control Setting” on page 17. B Perform steps 1 – 7. In step 3, the front display panel

C Leave the satellite receiver’s power on.

STOP +/–

DAILY (number key “8

HOWVIEW

shows “L2” for the channel position. In step 5, you cannot set “VPS/PDC” to “ON”.

in step 3. You can compensate for

WEEKLY (number key “9

pg. 36).

墌

number which starts with “0”.

”) for daily serials (Monday —

”) for weekly

HOWVIEW

ATT E NT I O N

Guide Program Number Set

“GUIDE PROG SET” appears after performing step 3 if the Guide Program number for the S entered has not been set. If you want to set the Guide Program number for the satellite broadcast station, press the PROG” to “SAT”. Press number on which your recorder or satellite receiver receives that station, then press OK or number. The S

HOWVIEW

rt to input the channel position

HOWVIEW

number key “0

e to set the Guide Program

Program screen appears.

(Example) To timer-record a ZDF programme with the S

HOWVIEW

* If your recorder receives ZDF on the channel position 2, press OK or

number you

” to change “TV

system.

after entering “2”.

Page 34

TIMER RECORDING (cont.)

Express Timer Programming

Before performing Express Timer Programming:

● Make sure that the recorder’s built-in clock is set properly.

● Insert a cassette with the safety tab in place. The recorder

will come on automatically.

● Turn on the TV and select the video channel (or AV mode).

If you do not know the S you wish to record, use the following procedure to set your recorder to timer-record the programme.

Access the S

Press

Press just starting out, “P1” appears.)

The front display panel looks like this:

Press time you want recording to start.

● Press and hold move in 30-minute increments, or press and release repeatedly to move 1 minute at a time.

PROG

Access the Programme screen.

START+/–

Enter the programme start time.

START+/–

HOWVIEW

. (If you’re

to enter the

START+/–

number for the programme

screen.

The front display panel looks like this:

Enter the programme stop time.

Press

STOP+/–

stop.

● Press and hold press and release repeatedly to move 1 minute at a time.

Press

DATE+/–

● The current date appears on the TV screen. The date you enter appears in its place.

to enter the time you want recording to

STOP+/–

to move in 30-minute increments, or

Enter the programme date.

Page 35

Enter the channel position.

Press

● It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”.

Press

● If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC” is lit on the front display panel, VPS/PDC is set to ON.

● If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC” is not lit on the front display panel, VPS/PDC is set to OFF.

墌

After confirming all information is correct, press

. “PROGRAM COMPLETED” appears on the TV

screen for about 5 seconds, then the normal screen appears. If “PROGRAM OVERLAPPED” appears on the TV screen and “Err” on the front display panel, see page 37.

● Repeat steps 1 – 9 for each additional programme.

PR+/–

Set the tape speed.

SP/LP/EP

(p).

(

墌

pg. 71

)

Set the VPS/PDC mode.

VPS/PDC

“VPS/PDC Recording” in the right column

to select “ON” or “OFF”.

Return to the normal screen.

PROG

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, “PROGRAM FULL” appears on the TV screen and “FULL” appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (

pg. 36).

墌

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

A Perform “Satellite Receiver Control Setting” on page 17. B Perform steps 1 – 10. In step 6, press the

to change “TV PROG” to “SAT”. The front display panel shows “L2” for the channel position. Then press enter the channel position for the satellite broadcast. In step 8, you cannot set “VPS/PDC” to “ON”.

C Leave the satellite receiver’s power on.

number key “0

PR+/–

”

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.

NOTES:

● When you use Express Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● VPS/PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/ DECODER connector on your recorder.

● VPS/PDC recording is also possible via the AV1 (L-1) IN/ OUT connector.

Engage the recorder’s timer mode.

Press # ( and “

” appears on the front display panel. The #

indicator on the recorder’s front panel also lights up.

● To disengage the timer mode, press

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press

”) for weekly serials or

key “9

serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.

). The recorder turns off automatically

TIMER

# (

TIMER

DAI LY (number key “8

) again.

WEEKLY (number

”) for daily

How to check if the station being received transmits a VPS/PDC signal

A Press

front display panel.

B Hold down

“VPS/PDC” appears blinking on the front display panel. If a VPS/PDC signal is detected from the station, “VPS/PDC” will stop blinking. If no VPS/PDC signal is detected from the station, “VPS/PDC” will blink at a slower rate.

C Press

until the channel position appears on the

––:––

for about 5 seconds.

START+

––:––

again to return to normal display.

START+

Page 36

TIMER RECORDING (cont.)

Access the Programme screen/display.

Press " again to check more information. Each time you press ", the next programme’s information appears.

The front display panel shows the programme start time. Pressing

changes the display to the programme stop time, then the

date and the channel position.

To cancel or change a programme...

Cancel or change a programme.

Press & to cancel a programme. To change programme settings, press the appropriate button:

STOP+/–, DATE+/–, PR+/–, VPS/PDC

(

● You can change “TV PROG” to “SAT” for the channel position by pressing the

number key “0

”.

START+/–

and/or

SP/LP/EP

Check, cancel and change programmes

Disengage the timer mode.

Press # (

Access the Programme Check screen/display.

Press ".

), then press 1.

TIMER

Return to the normal screen/display.

Press " as many times as necessary. If there are still some programmes remaining, go on to step 6.

Return to the timer mode.

Press # (

TIMER

NOTE:

You can also check the programmes on the front display panel even if the recorder’s power is off (unless the recorder is in the Power Save mode mode; however, it is not possible to cancel or change the programmes.

pg. 70) or the recorder is in the Timer

墌

Page 37

When programmes overlap each other

If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. The Programme Check screen appears and conflicting programmes will start blinking.

Example: Programme 1 (you have just made) and Programme 4 overlap each other.

Confirm the overlapping programmes.

Overlapping programmes blink on the TV screen.

Select the programme to modify.

Press rt, then press OK or e.

● You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press programme setting. The programme with the lower programme number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the recorder will return to the normal screen.

Cancel or change programme setting.

To cancel a programme,

screen you do not want is shown. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

To change a programme, START+/–, STOP+/–, DATE+/–, PR+/–, VPS/PDC SP/LP/EP

you want to make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

(

) when the Programme screen on which

press & when the Programme

press the appropriate button:

to finish the timer

PROG

and/or

NOTE:

If the overlap is not yet solved, or another overlap occurs with the timer programme setting after making the last correction on a programme, the conflicting programmes will be shown on the Programme Check screen again. Repeat the above steps again until the overlap is solved.

Page 38

Automatic Satellite Programme Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

SAT# indicator

TIMER RECORDING (cont.)

ATT E NT I O N

● Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

● If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

● Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

● Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. (

● Programme the timer on the satellite receiver.

● Insert a cassette with the safety tab in place.

Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT” (墌pg. 53).

● When you select “SAT”, refer to “IMPORTANT” on page 64.

Set the tape speed.

Press

SP/LP/EP

● It is not possible to select EP mode if “COLOUR SYSTEM” is set to “MESECAM”.

(p).

(

墌

pg. 71

)

pg. 64, 65)

墌

Engage the Automatic Satellite Programme

Recording mode.

Press and hold indicator lights up and the recorder turns off automatically.

for about 2 seconds. The SAT#

SAT#

NOTES:

● To disengage the Automatic Satellite Programme Recording mode, press

● If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

● In step 3, if the SAT

Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” (

* Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

● The SAT

● For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

● Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

● Pressing the recorder’s

● If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible

● Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may

● If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not

● You can also record a programme from your cable system in the same way if the system has a timer.

● The B.E.S.T. system (

● Just Clock (

● When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

# indicator blinks while Automatic Satellite Programme Recording is in progress.

disengages the Automatic Satellite Programme Recording mode.

to set different tape speeds for each programme.

record slightly longer than the actual length of the programme.

start Automatic Satellite Programme Recording even though the SAT and is turned back on again, the recorder starts recording.

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” (

pg. 69).

墌

# indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic

pg. 34) to timer-record a satellite programme.

墌

1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and

pg. 31) does not work while Automatic Satellite Programme Recording is in progress.

墌

pg. 80) does not work when the Automatic Satellite Programme Recording mode is engaged.

墌

#. The SAT# indicator goes off.

SAT

# indicator blinks. When the satellite receiver shuts off once

Page 39

REMOTE CONTROL FUNCTIONS

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

Remove the power supply.

Unplug the end of the mains power cord from the mains outlet.

Set the remote control code.

Press and hold seconds, press the

Re-supply the power.

Plug the end of the mains power cord into a mains outlet.

Turn on the recorder.

Press 1 on the remote control. The recorder will now only respond to B code signals.

on the remote control for over 2

VCR

number key “2

” and then press OK.

NOTE:

To set the recorder back to respond to A code signals, repeat the same procedure as shown above, but in step 2, press the

” instead of “2”.

key “1

number

Page 40

REMOTE CONTROL FUNCTIONS (cont.)

TV Multi-Brand Remote Control

Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled.

Before performing the following steps:

Turn off the TV using its remote control.

Set the TV brand code.

Refer to the chart below. Press and hold TV on the recorder’s remote control for over 2 seconds, enter your TV’s brand code using the

number keys

Press 1 on the recorder’s remote control to turn on the TV and try operations (墌 step 2).

● Once you have set the remote control to operate the TV, you do not have to repeat this step until you replace your remote control’s batteries.

● JVC or SAMSUNG has more than one code. If the TV does not function with one code, try entering another.

Operate the TV.

First, press TV to set the remote control to TV mode, then press the corresponding button: 1,

TV%+/–

● For some brands of TV, you must press OK after having pressed the

(Volume),

number keys

(TV Muting),

, then press OK.

TV/VCR, TV PR +/–

number keys

Control Your TV Using Additional Buttons

Use the

number keys

button to select the TV’s channel.

● With televisions under Code 01, 02, 07, 10, 11, 14, 20, 23, 24, 25, 27, 33 or 35, the 1-digit/2-digit entry switching button (often labelled – /– –) of your TV’s remote control.

● With televisions under Code 01, 28, 29 or 34, the button corresponds to the 10 + button, and the corresponds to the 20 + button of your TV’s remote control.

, and the p button, & button or #

p button corresponds to the

# button

NOTE:

The way these buttons are used is determined by your TV. Use these buttons as instructed for your TV’s remote control.

IMPORTANT

Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

BRAND NAME CODE

JVC BLAUPUNKT BRANDT FERGUSON FINLUX FUNAI LG/GOLDSTAR GRAETZ GRUNDIG HITACHI ITT LUXOR MITSUBISHI MIVAR NEC NOKIA NORDMENDE PANASO NIC PHILIPS SABA SALORA SAMSUNG SELECO SHARP SONY TELEAVIA TELEFUNKEN THOMSON TOSHIBA

01, 23, 24, 25 19 26 27 30 32 18 28 19 10 28 28 03 29 20 31 26 11 02 26 28 02, 12, 33, 34, 35 28 06 07 26 26 26 14

Page 41

Satellite Receiver Multi-Brand Remote Control

Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’s satellite receivers can also be controlled.

Before performing the following steps:

Turn off the satellite receiver using its remote control.

Set the satellite receiver brand code.

Refer to the chart in the right column. Press and hold

CABLE/SAT

seconds, enter your satellite receiver’s brand code using the Press 1 on the recorder’s remote control to turn on the satellite receiver and try operations (

● Once you have set the remote control to operate the satellite receiver, you do not have to repeat this step until you replace your remote control’s batteries.

● Some brands of satellite receiver have more than one code. If the satellite receiver does not function with one code, try entering another.

First, press satellite receiver mode, then press the corresponding button:

● For some brands of satellite receiver, you must press having pressed the

● The receivers.

on the recorder’s remote control for over 2

number keys

, then press OK.

墌

Operate the satellite receiver.

CABLE/SAT

TV PR +/–, number keys

number keys

to set the remote control to

number keys

may not function with some satellite

step 2).

p after

BRAND NAME CODE

JVC AMSTRAD CANAL SATELLITE CANAL + D-BOX ECHOSTAR ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN ITT NOKIA JERROLD KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASO NIC PHILIPS RFT SAGEM SALORA SIEMENS SKYMASTER TPS TRIAX WISI

73 60, 61, 62, 63, 92 81 81 85 78, 79, 80 82 68 89 88 64, 65 64, 78 68 75 70, 71 68 93 70 87 65, 67, 74, 86, 92 74 66, 84 69 83 68 64 69 83 91 64

IMPORTANT

Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability.

Page 42

Navigation

When you record a TV programme with this recorder, the recorder automatically stores in its memory the recording start time, date, channel information, etc. If the tape is recorded on this recorder for the first time, new tape number and the recording date are also registered. On the tape only the tape number information is recorded.

Turn on the TV and select the video channel (or AV mode).

VIDEO NAVIGATION

Navigation Playback

This function is useful when you wish to quickly find out what programmes you have recorded on a tape with this recorder. This function allows you to select a programme to watch, and then automatically searches for the start of the programme.

Load a recorded cassette.

Insert a cassette recorded on this recorder.

● While “– – – –” is blinking on the front display panel, the tape will run for a few seconds to search for the tape number.

Access the title screen.

Press

NAVIGATION

● After pressing access the title screen while the recorder searches for the programme information.

● If there is no cassette loaded, “FIND TITLE” screen appears. (

pg. 48)

墌

Select a programme.

Press rt to move the highlight bar (pointer) to the programme you want to watch.

NAVIGATION

, it may take a few seconds to

Start playback.

Press OK. Playback begins automatically after the selected programme is located.

Check Memory

You can check the amount of recorded information in the memory.

Access the Main Menu screen.

Press

Press highlight bar (pointer) to “VIDEO NAVIGATION”, then press OK or

Access the Video Navigation screen.

to move the

Page 43

Check the memory.

Press rt to move the highlight bar (pointer) to “CHECK MEMORY”, then press OK.

● The CHECK MEMORY screen will appear.

Return to the normal screen.

Press

Turn Off Navigation

If you do not want to record information on the programmes, set “NAVIGATION” to “OFF”.

Perform steps 1 to 2 of “Check Memory” on page 42 before continuing.

Turn off Navigation.

Press rt to move the highlight bar (pointer) to “NAVIGATION”, then press

Press

to set to “OFF”.

Return to the normal screen.

Video Navigation Title Screen

A Tape number B Tape title

If there is no tape title entered, the earliest recording date will be displayed.

C Current page number/total page number D Largest blank space on the tape

(Calculated remaining time based on the current tape speed (SP, LP or EP) selected on the recorder)

E Programme information

(Recording start time, date and channel number)

F Currently selected programme G Current tape position

“*” is displayed if the currently selected programme and the current tape position are different while tape is not running.

H Detailed information of currently selected programme

(Recording start time, end time, recording length, recording speed, programme title and category) If there are no title and category entered, “TITLE” and “CATEGORY” will be displayed.

NOTES:

● Video Navigation is possible with the cassettes recorded with this recorder only.

● To record the date and time as the programme title in this recorder’s memory, make sure the recorder’s clock is set correctly before recording.

● To record the programme information in this recorder’s memory, you must continue to record each programme for over the minimum recording time; 8 minutes for the SP mode, 15 minutes for the LP mode or 23 minutes for the EP mode.

● Video Navigation may not work properly when an index code (VISS signal) is marked or erased manually near a start point of recorded programme. (

● Video Navigation may not work properly depending on the tape being used.

● If the recorder finds two tape numbers in one tape while playing back or searching for the beginning of a programme, then when you remove the tape, the tape will be assigned just one number (smaller number).

● The programme information is stored in this recorder’s memory. If the memory in this recorder should ever be damaged and the programme information lost, it is impossible to restore that information.

● After recording a tape with this recorder, write the tape number on a label and affix the label to the cassette in order to allow you to find the tape by its number.

墌

pg. 22)

Page 44

Find Blank Space

This function is useful for finding out the blank space on each cassette and recording a new programme there.

Perform steps 1 to 2 of “Check Memory” on page 42 before continuing.

VIDEO NAVIGATION (cont.)

Edit Title

You can edit the tape title and the programme titles as you like. You can also select the category for each programme. In short, you can use the Video Navigation function to create your own video tape library.

Access the Find Blank Space screen.

Press rt to move the highlight bar (pointer) to “FIND BLANK SPACE”, then press OK.

Select the tape number.

Press rt to move the highlight bar (pointer) to the tape number on which you want to record a programme, then press OK.

● The calculated blank space is based on the current tape speed (SP, LP or EP) selected on the recorder.

● If the selected cassette has already been loaded, the recorder searches the beginning of the blank space and goes into the stop mode automatically.

Turn on the TV and select the video channel (or AV mode).

Load a cassette.

Insert the cassette whose number is displayed on the screen.

● The recorder searches the beginning of the blank space and goes into the stop mode automatically.

NOTE:

The recorder may not go into the stop mode right on the beginning of the selected blank space.

Page 45

Edit Tape Title

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “VIDEO NAVIGATION”, then press OK or

Press highlight bar (pointer) to “EDIT TITLE”, then press OK or

Press highlight bar (pointer) to the tape number whose title you want to edit, then press OK or e.

● The “*” mark indicates the tape number of the cassette that is currently in the recorder.

Access the Video Navigation screen.

Access the Edit Title screen.

to move the

Select the tape number.

to move the

Enter the tape title.

Press the press OK. For details, refer to “Entering Character” below.

Press

number keys

Return to the normal screen.

and e to enter characters, then

Entering Character

Press the appropriate each character. Refer to the example below.

(Example) Enter “JVC NEWS”

Press 5 (JKL) once to enter “J”, then press

Press 8 (TUV) three times to enter “V”, then press

Press 2 (ABC) three times to enter “C”, then press

Press 0 (

Press 6 (MNO) twice to enter “N”, then press

Press 3 (DEF) twice to enter “E”, then press

Press 9 (WXYZ) once to enter “W”, then press

Press 7 (PQRS) four times to enter “S”, then press

NUMBER KEY CHARACTER

) twice to enter “I (space)”, then press e.

number key

, then press e to enter

f ( ) 1

. , / – + A B C 2 Ä À Á Â Ã Å Æ D E F 3 È É Ë Ê G H I 4 Î Ï Ì Í J K L 5 M N O 6 Ö Ô Ò Ó Õ Ø Ñ P Q R S 7 T U V 8 Ü Ù Û Ú W X Y Z 9 0 _

Select the tape title.

Press rt to move the highlight bar (pointer) to the tape number, then press OK or

. The tape title begins

blinking.

● The “*” mark indicates the current position on the tape.

NOTES:

● If you make a mistake, press enter the correct character.

● If you want to delete a character, press character, then press

w e to select the character, then

w e to select the

Page 46

VIDEO NAVIGATION (cont.)

Edit Programme Title and Category

Perform steps 1 to 4 of “Edit Tape Title” on page 45 before continuing.

Select the programme.

Press rt to move the highlight bar (pointer) to the programme you want to edit, then press OK or “TITLE” display begins blinking.

Enter the programme title.

Press the press OK. For details, refer to “Entering Character” on page 45.

Press category you want, then press OK or e.

number keys

Select the category.

to select the

. The

and e to enter characters, then

Choice of Category

CATEGORY

MOVIE

r t

SPORTS

r t

SPECIAL

r t

SERIES

r t

SHOW

r t

MUSIC

r t

CHILDREN

r t

NEWS

r t

OTHERS

Return to the normal screen.

Press

Page 47

Delete Tape Data

Perform steps 1 to 4 of “Edit Tape Title” on page 45 before continuing.

Select the tape title.

Press rt to move the highlight bar (pointer) to the tape number you want to delete, then press

Delete the tape data.

Press highlight bar (pointer) to “YES”, then press OK or

to move the

Delete Programme Data

Perform steps 1 to 4 of “Edit Tape Title” on page 45 before continuing.

Select the programme.

Press rt to move the highlight bar (pointer) to the programme you want to delete, then press

Delete the programme data.

Press highlight bar (pointer) to “YES”, then press OK or

to move the

Return to the normal screen.

Press

Return to the normal screen.

Press

NOTES:

● When you delete data, only the tape and/or programme information is deleted from the recorder’s memory. The actual recording on the tape is not erased.

● If the recorder’s memory becomes full, the recorder cannot register any more information. Delete any unnecessary data of tape or programme from the recorder’s memory.

Page 48

Find Title

VIDEO NAVIGATION (cont.)

Sort By Tape Number

This function is useful for finding out the programme you want to playback in the order sorted by tape number.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “VIDEO NAVIGATION”, then press OK or

Press highlight bar (pointer) to “FIND TITLE”, then press OK or

Access the Video Navigation screen.

Access the Find Title screen.

to move the

Page 49

Access the Tape No. screen.

Press rt to move the highlight bar (pointer) to “BY TAPE NO.”, then press OK or

Select the programme.

Press highlight bar (pointer) to the programme you want to play back, then press OK.

● If the selected cassette has

Insert the cassette whose number is displayed on the screen.

● Playback begins automatically

to move the

already been loaded, playback begins automatically after the selected programme is located.

Load a cassette.

after the selected programme is located.

Sort By Date

This function is useful for finding out the programme you want to play back in the order sorted by date.

Perform steps 1 to 3 of “Sort By Tape Number” on page 48 before continuing.

Access the Date screen.

Press rt to move the highlight bar (pointer) to “BY DATE”, then press OK or

Select the programme.

Press highlight bar (pointer) to the programme you want to play back, then press OK.

● If the selected cassette has

Insert the cassette whose number is displayed on the screen.

● Playback begins automatically

to move the

already been loaded, playback begins automatically after the selected programme is located.

Load a cassette.

after the selected programme is located.

Page 50

VIDEO NAVIGATION (cont.)

Select the category.

Press rt to move the highlight bar (pointer) to the category you want to watch, then press OK.

Select the programme.

Press highlight bar (pointer) to the programme you want to play back, then press OK.

● If the selected cassette has

Insert the cassette whose number is displayed on the screen.

● Playback begins automatically

to move the

already been loaded, playback begins automatically after the selected programme is located.

Load a cassette.

after the selected programme is located.

Sort By Category

This function is useful for finding out the programme you want to play back in the order sorted by category.

Perform steps 1 to 3 of “Sort By Tape Number” on page 48 before continuing.

Access the Category screen.

Press rt to move the highlight bar (pointer) to “BY CATEGORY”, then press OK or

Page 51

EDITING

Edit From A Camcorder

If the camcorder has no S-VIDEO output connector ...

Recorder

You can use a camcorder as the source player and your recorder as the recording deck.

Make connections.

If the camcorder has no S-VIDEO output connector ...

... connect the camcorder’s AUDIO OUT and VIDEO OUT connectors to the recorder’s front panel AUDIO and VIDEO input connectors. If the camcorder has an S-VIDEO output connector ...

... connect the camcorder’s AUDIO OUT and S-VIDEO OUT connectors to the recorder’s front panel AUDIO and S-VIDEO input connectors.

● When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder.

● When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder’s instruction manual for operating procedure.

AUDIO input

Camcorder

Player

If the camcorder has an S-VIDEO output connector ...

Recorder

S-VIDEO input

VIDEO input

Video cable

(not provided)

Audio cable (not provided)

AUDIO OUT

VIDEO OUT

EDIT

AUDIO input

To rear panel PAUSE/R.A.EDIT connector

Mini-plug cable (not provided) (JVC camcorder only)

To rear panel PAUSE/R.A.EDIT connector

Set the recorder’s input mode.

Press

AUX (number key “0

the AUDIO and VIDEO input connectors, or “S-1” for the AUDIO and S-VIDEO input connectors, depending on the connectors being used.

Set the edit mode.

See “PICTURE CONTROL” on page 69.

Start the camcorder.

Engage the Play mode of the camcorder.

Start the recorder.

Engage the Record mode of the recorder.

”) and/or PR to select “F-1” for

NOTES:

● All necessary cables can be obtained from your dealer.

● When you select “EDIT” to dub tapes in step 3, be sure to

select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you finish dubbing the tapes.

Audio cable (not provided)

S-Video cable (provided) Mini-plug cable

S-VIDEO OUT

Camcorder

AUDIO OUT

EDIT

Player

(not provided) (JVC camcorder only)

Page 52

Output/Input Set

EDITING (cont.)

Access the Output/Input Set screen.

Press rt to move the highlight bar (pointer) to “OUTPUT/INPUT SET”, then press OK or

Select the output or input mode for the AV1 (L-1) IN/OUT connector.

Press rt to move the highlight bar (pointer) to “L-1 OUTPUT” or “L-1 INPUT”. Then, press OK or the appropriate setting.

* The default setting is

the table below.

L-1 OUTPUT

: If a connected appliance’s input is

VIDEO

S-VIDEO:

to select

bold

compatible only with regular video signals, set to “VIDEO”. If a connected appliance’s input is compatible with Y/C signals, set to “S-VIDEO”. You can obtain high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

L-1 OUTPUT and L-1 INPUT Setting

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set “L-1 OUTPUT” and “L-1 INPUT” to the appropriate mode depending on the type of appliance connected to the recorder’s AV1 (L-1) IN/OUT connector.

Access the Main Menu screen.

Press

L-1 INPUT

: If a connected appliance’s output is

VIDEO

S-VIDEO

Return to the normal screen.

Press

compatible only with regular video signals, set to “VIDEO”.

: If a connected appliance’s output is

compatible with Y/C signals, set to “S-VIDEO”. You can obtain high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

NOTES:

● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-1 INPUT” to “S-VIDEO”.

● If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-1 INPUT” to “S-VIDEO”.

Page 53

L-2 SELECT and L-2 INPUT Setting

The AV2 (L-2) IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the recorder’s AV2 (L-2) IN/ DECODER connector. Set “L-2 INPUT” to the appropriate mode depending on the output signals of the connected appliance.

Perform steps 1 and 2 of “L-1 OUTPUT and L-1 INPUT Setting” on page 52.

Select the input mode for the AV2 (L-2) IN/

DECODER connector.

Press rt to move the highlight bar (pointer) to “L-2

” or “L-2 INPUT”.

SELECT

Then, press OK or the appropriate setting.

* The default setting is

the table below.

L-2 SELECT

: To use this recorder as the recording

A/V

DECODER

: To view a satellite programme with

SAT

to select

bold

deck with the player connected to the AV2 (L-2) IN/DECODER connector, or to use the satellite receiver connected to the AV2 (L-2) IN/DECODER connector.

: To use a decoder connected to the

AV2 (L-2) IN/DECODER connector.

the TV set while the recorder is turned off. (

墌

pg. 64)

NOTES:

● If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.

● If you are not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave “L-2 SELECT” set to “A/V”.

● The default setting is “A/V”; if the recorder’s memory backup has expired due to a power cut or because the AC was removed from the recorder, “A/V” will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set “L-2 SELECT” back to appropriate mode.

● When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV screen or front display panel instead of “L-2” or “L2”.

● If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-2 INPUT” to “S-VIDEO”.

● If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-2 SELECT” to “DECODER”.

L-2 INPUT

: If a connected appliance’s output is

VIDEO

S-VIDEO

Return to the normal screen.

Press

compatible only with regular video signals, set to “VIDEO”.

: If a connected appliance’s output is

compatible with Y/C signals, set to “S-VIDEO”. You can obtain high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

Page 54

Edit To Or From Another Video Recorder

EDITING (cont.)

You can use your recorder as the source player or as the recording deck.

Make connections.

Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated on page 55.

When using your recorder as the source player ...

... connect its AV1 (L-1) IN/OUT connector to the recording deck. When using your recorder as the recording deck ...

... connect its AV1 (L-1) IN/OUT or AV2 (L-2) IN/ DECODER connector to the source player. If another recorder is compatible with the Y/C signal ...

... connect your recorder’s AV1 (L-1) IN/OUT connector to another recorder.

With C connection ...

● When using your recorder as the recording deck, set “L-1 INPUT” to “S-VIDEO” and “L-2 SELECT” to “A/V” (

53).

● When using your recorder as the source player, set “L-1 OUTPUT” to “S-VIDEO” (

Set the input mode of recording deck.

With this video recorder, press and/or PR to select “L-1” for the AV1 (L-1) IN/OUT connector, or “L-2” for the AV2 (L-2) IN/DECODER connector, depending on the connector being used.

● When using another recorder as the recording deck, refer to its instruction manual.

● When using the AV2 (L-2) IN/DECODER connector, set “L-2 SELECT” to “A/V” (

墌

pg. 53).

pg. 52).

AUX (number key “0

墌

pg. 52,

”)

Advantages of S-VHS video recorders

You can edit from VHS to S-VHS, S-VHS to VHS, or, from S-VHS to S-VHS.

● From VHS to S-VHS: Record VHS playback signals in the S-VHS mode. Although the picture quality is inherently limited by that of the original, the edited tape has better picture quality than those made by VHS-to-VHS editing.

● From S-VHS to VHS: Because the picture quality of the source material is very high, the edited tape has better picture quality than those made by VHS-to-VHS editing.

● From S-VHS to S-VHS: All signals will be transferred with minimum degradation.

Set the edit mode.

See “PICTURE CONTROL” on page 69.

Start the source player.

Engage the Play mode of the source player.

Start the recording deck.

Engage the Record mode of the recording deck.

Page 55

TV receiver

Video channel or AV mode

RF cable (provided)

Player

21-pin SCART cable

(not provided)

Another recorder

Your recorder

Recorder

21-pin SCART cable

(not provided)

Another recorder

Your recorder

RF cable (provided)

TV receiver

Video channel or AV m ode

Recorder

Player

TV receiver

Recorder

S-Video cable

(provided)

21-pin SCART cable

(not provided)

Another recorder

Player

Your recorder

NOTES:

● All necessary cables can be obtained from your dealer.

● For Y/C signal input/output, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.

● When you select “EDIT” to dub tapes in step 3, be sure to select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you

finish dubbing the tapes.

● When you use this recorder as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting (

● If you are using another recorder with S-Video and Audio input/output connectors, you can connect those connectors to this

recorder’s S-VIDEO and AUDIO input/output connectors. When using your recorder as the source player ... ... connect its rear panel S OUT and AUDIO OUT connectors to the recording deck’s S-Video and Audio input connectors. When using your recorder as the recording deck ... ... connect its front panel S-VIDEO and AUDIO input connectors to the source player’s S-Video and Audio output connectors. Then, set the recorder’s input mode to “S-1”.

墌

pg. 69).

Page 56

Audio Dubbing

Audio Dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack.

ATTENTION:

Audio dubbing is not possible with a cassette recorded in EP mode.

EDITING (cont.)

Normal audio track

Video/Hi-Fi audio track

Your recorder

CD player, etc.

Pre-recorded tape

Audio-dubbed tape

Mixer output

CD player, etc.

Audio mixer

Original sound

AUDIO OUT

Your recorder

Page 57

Make connections.

Connect an audio component to the AUDIO L + R input connectors on the recorder’s front panel.

● When connecting a monaural audio component, use only the recorder’s AUDIO L input connector.

Set the recorder’s input mode.

Press

AUX (number key “0

“S-1”.

Locate the start point.

Press 4 to start playback of the tape in your recorder, and

when you reach the point where you want to start

press

dubbing.

Engage the Audio Dubbing mode.

Press

● Your recorder enters the Audio Dubbing Pause mode. (“ blinks, “

● To perform Audio Dubbing with audio mixing, press to select “

* Audio Dubbing with audio mixing is not possible if you are using a

monaural audio component, or if you don’t have an audio mixer.

A.DUB

u” and “i” light up on the front display panel.)

a + s (L+R)” at this point.

”) and/or PR to select “F-1” or

o”

AUDIO

Start dubbing.

Engage the audio component’s Play mode, then press 4 to start the tape in your recorder; Audio Dubbing begins at this point.

● “

o” blinks and “u” is displayed on the front display panel.

● To stop dubbing temporarily, press dubbing.

End Audio Dubbing.

Press 8 (or engage the audio component’s Stop mode.

) to stop the tape in your recorder, and

9. Press 4 to resume

NOTES:

● When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the mixed sound (Hi-Fi + Normal soundtracks), press

to select “

AUDIO

● Audio Dubbing stops automatically when the counter reaches “0:00:00”, and the recorder enters the Play mode. Check the counter reading before dubbing.

● Audio Dubbing is also possible using the rear panel AV1 (L-1) IN/OUT or AV2 (L-2) IN/DECODER connector. When using these 21-pin SCART connectors, be sure to select the correct input mode (“L-1” or “L-2”) in step 2.

● Audio Dubbing is not possible with cassettes whose record safety tab has been removed.

● When playing back an audio-dubbed tape, press select the soundtrack you wish to hear. (

a + s (L+R) + NORM” (

墌

pg. 23)

pg. 23).

AUDIO

Page 58

Insert Editing

Insert Editing replaces part of the recorded scene with new material. Both the picture and Hi-Fi audio soundtrack are replaced with new ones, while the normal audio soundtrack remains unchanged. If you wish to change the normal audio track as well, use the Audio Dubbing function simultaneously. For Insert Editing, use your recorder as the recording deck.

ATTENTION:

Insert editing is not possible with a cassette recorded in EP mode.

Source tape

EDITING (cont.)

Recording tape

Recorder

Before Insert Editing

After Insert Editing

Audio/Video signalS-Video signal

Normal audio track

Video/Hi-Fi audio track

Your recorder

Player

Another recorder

Page 59

Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your recorder’s VIDEO or S-VIDEO and AUDIO input connectors on the front panel.

Set the recorder’s input mode.

Press

AUX (number key “0

the AUDIO and VIDEO input connectors or “S-1” for AUDIO and S-VIDEO input connectors.

Locate the end point.

Load the recording cassette into your recorder, and play it back to determine the edit-out point (the end of the segment to be replaced) using the

dial, or pressing

JOG

Reset the counter.

Press

The counter is reset to “0:00:00”.

●

Determine the edit-in point (the beginning of the segment to be replaced) using the or pressing w e and 9.

● Be sure to engage the Still mode at the edit-in point.

Press

● Your recorder enters the Insert Pause mode. (“ “

i” light up on the front display panel.)

● The TV screen changes from the still picture to the input source you are going to record.

0000

Locate the start point.

Engage the Insert Editing mode.

INSERT

”) and/or PR to select “F-1” for

ring or the

o”, “u” and

w e

SHUTTLE

and 9.

SHUTTLE

ring or the

JOG

dial,

Start Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press 4 to start the tape in your recorder; Insert Editing begins at this point.

● “

o” and “u” are displayed on the front display panel.

End Insert Editing.

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press

0000

AV Insert Editing

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ... ... In step 6, after you press (

” and “u” blink and “i” lights up on the front display

“o

panel.)

NOTES:

● All necessary cables can be obtained from your dealer.

● Insert Editing is not possible with cassettes whose record safety

tab has been removed.

● When Insert Editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

● In Insert Editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point.

● A small portion of the recording which precedes an insert edit may become erased.

● Insert Editing is also possible using the rear panel AV1 (L-1) IN/ OUT or AV2 (L-2) IN/DECODER connector. When using these 21-pin SCART connectors, be sure to select the correct input mode (“L-1” or “L-2”) in step 2.

INSERT

, press

A.DUB

also.

Page 60

Random Assemble Editing

Player

Audio signal Video signal

Another recorder

(with PAUSE connector)

Your recorder

EDITING (cont.)

This function makes it easier to create edited videos when your recorder is used as the source player in combination with another JVC video recorder equipped with a Remote PAUSE connector. You can pre-program up to 8 scenes or “cuts” for automatic editing in the sequence you have specified. You can also perform Random Assemble Editing with a second non-JVC recorder. (

Make connections.

Connect your recorder’s AV1 (L-1) IN/OUT or S-VIDEO OUT/AUDIO OUT connectors to the video and audio input connectors on the recording deck, and connect your recorder’s PAUSE/R.A.EDIT connector to the PAUSE connector on the recording deck.

● If the recording deck does not have a PAUSE connector, connect to the R.A.EDIT connector instead.

● The Mini-plug cable is a mono 3.5 mm mini-plug to mono

3.5 mm mini-plug connector.

Set the input mode of recording deck.

Insert the cassette to be recorded on into the recording deck and set the input mode of the recording deck.

Load the source cassette.

Insert the source cassette into your recorder.

● Use a source cassette that is recorded in SP or LP mode.

墌

pg. 61)

Recorder

Mini-plug cable

(not provided)

Set the edit mode.

See “PICTURE CONTROL” on page 69.

Start playback of the source cassette.

Press 4.

Access the R.A.Edit screen.

Press

R.A.EDIT

Press

to move the highlight bar (pointer) to “R.A.EDIT”, then press OK.

● The R.A.Edit screen is superimposed on the video playback in step 7.

to access the Main Menu screen. Press rt

Page 61

Locate the start point.

Find the edit-in point on the source tape from where you want the edited scene to begin by pressing using the the

OUT

● The edit-in point is registered in memory and appears on the screen.

Find the edit-out point where you want the edited scene to end by pressing the dial, then press

PROG

● The edit-out point is registered in memory and appears on the screen.

● The total time of the edited scenes is displayed to the right of “(+)”.

● Repeat steps 7 and 8 for each additional scene.

SHUTTLE

dial, then press

JOG

(or

PROG

Locate the end point.

SHUTTLE

ring or the

w e

ring or

or using

w e

IN/OUT

IN/

JOG

(or

To Make Corrections ...

... in step 7 or 8, you can cancel registered in and out points by pressing

● If, for example, you have registered 5 sets of in and out points

&. Each time you press, the preceding point is erased.

and want to reset the first set, you have to press & until all points after the first set have been erased. Reenter them after you have repaired the first set of points.

NOTES:

● You can also monitor the sound when searching for scenes you want to edit in steps 7 – 8. Since you can hear the soundtrack during selection, you can avoid abrupt or unnatural sounding scene-to-scene transitions. The sound that is heard, however, is not TimeScan Audio.

● When editing, there may be a discrepancy of about 2 seconds on the source tape between the locations you chose as edit-in and -out points and the locations your recorder recognizes as those points.

● For any scene, the edit-out point must have a counter reading that is at least 1 second after the corresponding edit-in point. Any less than 1 second and the edit-out point will not be registered.

● Since the source recorder prerolls during Random Assemble Editing, there must be at least 15 seconds worth of recorded material prior to any edit-in point on the source tape.

● If the search time for an edit-in point exceeds 5 minutes, the recording deck enters its Stop mode and editing will not take place.

● During steps 7 and 8 — if you engage the Pause mode while registering edit-in and -out points in the R.A.Edit screen, the characters in the on-screen display may become distorted. This is normal.

Prepare the recording deck.

Engage its Record-Standby mode.

Start Random Assemble Editing.

Press

● Automatic editing begins; all the specified scenes are copied to the recording deck in the order they were registered.

● The on-screen display remains while your recorder searches for each scene (blinking cursor indicates scene currently being searched for), but disappears during actual editing.

● During scene search, the recording deck automatically enters its Record-Standby mode.

● When all registered scenes have been edited, your recorder enters the Pause mode, the recording deck enters its Record-Standby mode, and the cursor blinks at the next available number.

Press the Stop mode for your recorder and for the recording deck.

(or OK).

START

End Random Assemble Editing.

to return to the normal screen, and engage

Memory Capacity

Random Assemble Editing shares memory space with the recorder’s timer. If there are programmes occupied by timer-recording data, those spaces cannot be used to register edit-in and -out points — meaning you will not be able to edit 8 scenes.

● When all 8 programmes are full, “PROGRAM FULL” appears on the R.A.Edit screen.

● To cancel a programme, see page 36.

RM-V704U Multi-Brand Random Assemble Edit Controller (Not provided)

By connecting this controller to your recorder’s R.A.EDIT connector, you can perform Random Assemble Editing in combination with a second non-JVC video recorder. The controller is compatible with various major recorder brands. For compatible systems and availability, please consult your JVC dealer.

NOTE:

Although the RM-V704U is designed to operate the recording deck, it may not work with some recorders, or may have limited function capability.

Page 62

Synchro Editing

Recorder

EDITING (cont.)

The Synchro Editing function synchronizes the start of the playback and recording operations when starting an edit operation using a camcorder with LANC connector and your recorder.

Make connections.

Connect your recorder to camcorder (墌pg. 51), and connect your recorder’s SYNCHRO EDIT connector to the camcorder’s LANC connector.

Set the recorder’s input mode.

Press

AUX (number key “0

the AUDIO and VIDEO input connectors, or “S-1” for the AUDIO and S-VIDEO input connectors, depending on the connectors being used.

Set the edit mode.

See “PICTURE CONTROL” on page 69.

Locate the start point.

Start playback of the tape in the camcorder, and pause playback when you find the point where you want to start editing. Press and hold 9 and press 7 on your recorder so that the recorder enters the Record-Pause mode.

”) and/or PR to select “F-1” for

Camcorder

Player

LANC cable

(not provided)

To LANC connector

SYNCHRO EDIT connector

Start Synchro Editing.

Press

SYNCHRO

Pause Synchro Editing.

Press

SYNCHRO

● Repeat steps 4 – 6 as necessary.

7/79.

7/79 again.

NOTES:

● The Synchro Editing function may not work with the initial part of a camcorder tape.

● The Synchro Editing function cannot be used when using the JLIP function. (Pressing function.)

● The Synchro Editing function may not work properly with some type of camcorder.

● When you select “EDIT” to dub tapes in step 3, be sure to select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you finish dubbing the tapes.

SYNCHRO

7/79 cancels the JLIP

Page 63

Information On J Terminal

J terminal

J Terminal [JLIP (Joint Level Interface Protocol) Connector]

The J terminal is used to connect the recorder to a personal computer or similar device to allow computerized control of the recorder during editing and certain other operations.

Examples:

With the optional JLIP VIDEO CAPTURE BOX GV-CB3E:

● Enables Random Assemble Editing of up to 99 segments, using this recorder as the source player.

● Allows you to capture still images from the recorder into a personal computer.

For further details consult your nearest JVC dealer.

JLIP ID Number

Your recorder has its own JLIP ID number. This ID number must be unique when your recorder is connected to another device via its J terminal. The ID number is preset to “1” at the factory. You can change this number to any number between “1” and “99”. If it is necessary to change the JLIP ID number, perform the following steps.

Access the Main Menu screen.

Press

Access the Initial Set screen.

Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or

Access the JLIP ID No. Set screen.

Press rt to move the highlight bar (pointer) to “JLIP ID NO. SET”, then press

Press the enter the desired ID number, then press OK.

Set the JLIP ID number.

number keys

Return to the normal screen.

Press

Page 64

SYSTEM CONNECTIONS

Connecting To A Satellite Receiver

Simple Connections

This is an example of simple connection if your TV has one 21-pin AV input (SCART) connector.

Connect the satellite receiver to the AV2 (L-2) IN/ DECODER connector, then connect the AV1 (L-1) IN/ OUT connector to the TV’s connector.

Outdoor unit

Aerial

Satellite cable

Satellite receiver

NOTES:

● Set “L-2 SELECT” to “A/V” (

● You can use Automatic Satellite Programme Recording

function (

● To record a programme via the satellite receiver, select L-2 mode by pressing “L-2” appears on the front display panel.

● For details, refer to the instruction manual of the satellite receiver.

TV aerial cable

ANT. IN

RF OUT

21-pin SCART connector

pg. 38) with this connection.

墌

AUX (number key “0

Aerial connector

pg. 53).

墌

Back of TV

”) and/or PR so that

Back of recorder

Mains outlet

IMPORTANT

When you set “L-2 SELECT” to “SAT” (墌pg. 53), it is possible to view a satellite broadcast with the TV set to its AV mode even if the recorder is turned off. When the recorder is in Stop mode or recording, press indicator on the front display panel.

● If you turn on the recorder when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press

on the remote control to set the recorder to the video mode.

TV/VCR

on the remote control to turn off the VCR

TV/VCR

Page 65

Perfect Connections

This is an example of recommended connection if your TV has two 21-pin AV input (SCART) connectors.

Connect the decoder to the satellite receiver’s connector if you have a decoder, AV1 (L-1) IN/OUT connector to TV’s connector, and AV2 (L-2) IN/DECODER connector to the satellite receiver’s connector. Then connect the satellite receiver and TV.

Outdoor unit

Aerial

Satellite cable

Satellite receiver

NOTES:

● Set “L-2 SELECT” to “A/V” (

● You can use Automatic Satellite Programme Recording

function (

● To record a programme via the satellite receiver, select L-2 mode by pressing “L-2” appears on the front display panel.

● To receive a scrambled broadcast, descramble the signal with the satellite receiver.

● For details, refer to the instruction manual of the satellite receiver and decoder.

TV aerial cable

pg. 38) with this connection.

墌

AUX (number key “0

21-pin SCART connector

ANT. IN

RF OUT

pg. 53).

墌

Back of TV

”) and/or PR so that

Aerial connector

Mains outlet

Decoder

Back of recorder

Page 66

Connecting/Using

SYSTEM CONNECTIONS (cont.)

The AV2 (L-2) IN/DECODER connector can be used as an input connector for an external decoder (descrambler). Simply connect a decoder and you can enjoy the variety of programming that is available through scrambled channels.

A Decoder

TV receiver

(provided)

RF cable

TV aerial cable

Select the input mode.

Set “L-2 SELECT” to “DECODER”. (墌pg. 53)

Connect the decoder.

Connect your recorder’s AV2 (L-2) IN/DECODER connector to the decoder’s 21-pin SCART connector using a 21-pin SCART cable.

Set the tuner.

Perform the procedure as described in “When Receiving A Scrambled Broadcast” on page 75.

Decoder

AV1 (L-1) IN/OUTAV2 (L-2) IN/DECODER

Page 67

Connecting/Using A Stereo System

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.

FM tuner

CD player

Stereo amplifier

AUX IN or TAPE MONITOR

Audio cable (not provided)

Speaker Television Speaker

Mains outlet

AUDIO OUT

Make connections.

Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR connectors on your stereo system’s receiver or amplifier.

NOTE:

When listening to sound through the connected stereo system, turn the TV’s volume down completely.

Back of recorder

CAUTIONS:

● This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

● Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Page 68

Mode Set

SUBSIDIARY SETTINGS

You can change various mode settings on the Mode Set screen by following the procedure described below.

For each mode setting, see pages 69 to 71.

●

Turn on the TV and select the video channel (or AV mode).

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “MODE SET”, then press OK or

Press rt to move the highlight bar (pointer) to the item you want to change.

Access the Mode Set screen.

Select the mode.

Select the mode setting.

Press OK or e.

Return to the normal screen.

Press

Page 69

B.E.S.T.

OFF

PICTURE CONTROL

: Provides the optimised picture

AUTO

: Minimizes picture degradation

EDIT

: Reduces image coarseness when

SOFT

: Clearer, sharper-edged picture when

SHARP

AUTO TIMER

OFF

benefits of the B.E.S.T. Picture System.

during editing (recording and playback).

viewing overplayed tapes containing a lot of noise.

viewing images with lots of flat, same-coloured surfaces such as cartoons.

* The default setting is

in the table below.

bold

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking) system to “ON” or “OFF” (

墌

pg. 31).

This feature helps you to adjust the playback picture quality according to your preference. Normally select “AUTO”.

NOTES:

●

When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you select another mode.

●

When you select “EDIT” to dub tapes, be sure to select “AUTO” after you finish dubbing the tapes.

●

When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches automatically from “AUTO” to “NORM”.

When this function is set to “ON”, the timer is automatically engaged when the recorder power is turned off, and automatically disengaged when the recorder is powered back on.

NOTE:

For safety, when “AUTO TIMER” is set to “OFF”, all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press

# (TIMER).

O.S.D.

OFF

DIRECT REC

OFF

When this function is set to “ON”, various operational indicators appear on the TV screen. Messages appear in the selected language (

pg. 15, 16).

墌

NOTES:

●

When you use this recorder as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting.

●

During playback, the operation mode indicators may be disturbed depending on the type of tape being used.

When this function is set to “ON”, you can easily start recording the programme that you are watching on your TV. Press and hold or press

on the recorder.

and press 4 on the remote control,

NOTES:

●

When you use the Direct Rec function, be sure to use a TV offering T-V LINK, etc. and connect a fully-wired 21-pin SCART cable between the recorder and the TV (

●

If “DIRECT REC” is set to “OFF”, the described in “Basic Recording” (

●

During the Direct Rec, “– –” appears on the front display panel.

●

If a programme is recorded with the Direct Rec, the station name will not be registered for the Video Navigation. “– – – –” will be displayed for the station name.

●

Retake function (

pg. 28) does not work during Direct Rec.

墌

pg. 10).

墌

7 button functions as

pg. 26).

Page 70

SUBSIDIARY SETTINGS (cont.)

AUTO SP]LP TIMER

OFF

DIGITAL 3R

OFF

* The default setting is

in the table below.

bold

When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire programme while timer-recording in SP mode.

For Example . . .

Recording a programme of 210 minutes in length onto a 180-minute tape

Approximately 150 minutes Approximately 60 minutes

SP mode LP mode

Total 210 minutes

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

●

If you have programmed the recorder to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set “AUTO SP

]LP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set

the tape speed manually during timer programming.

●

In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.

●

There may be some noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode.

●

The Auto SP and the feature will not work properly with any tapes longer than E-180, or with some tapes of shorter lengths.

●

If you perform timer recording with both VPS/PDC and the Auto SP activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety.

]LP Timer feature is not available during ITR (Instant Timer Recording),

]LP Timer

When this function is set to “ON”, the Digital 3R picture system applies edge correction to the luminance signal to enhance detail.

NOTES:

●

Normally it is recommended to keep “DIGITAL 3R” set to “ON”.

●

Depending on the type of tape being used, picture quality may be better with “DIGITAL 3R” set to “OFF”.

●

If you use the recorder as the source player for editing, be sure to set “DIGITAL 3R” to “OFF” before starting.

POWER SAVE

OFF

VIDEO STABILIZER

OFF

When this function is set to “ON”, you can reduce the power consumption while the recorder is turned off.

NOTES:

●

During Power Save mode ... ... the front display panel will be turned off. ... the Just Clock function ( ... the picture may be distorted momentarily when you turn on/off the recorder.

●

Power Save does not work when ... ... the recorder is in the Timer mode. ... the recorder’s power is turned off after timer-recording or Instant Timer Recording. ... the Automatic Satellite Programme Recording mode is engaged ( ... “L-2 SELECT” is set to “DECODER” or “SAT” (

pg. 80) does not work.

墌

pg. 53).

墌

pg. 38).

When this function is set to “ON”, you can automatically correct vertical vibration in the picture when playing back unstable recordings made on another recorder.

NOTES:

●

When you finish viewing a tape, be sure to set this function to “OFF”.

●

Regardless of the setting, this function has no effect during recording and during special effects playback.

●

The on-screen display may jitter vertically when this function is set to “ON”.

●

To watch recordings with close-caption, set this function to “OFF”.

●

Video Stabilizer and Digital TBC/NR cannot be used at the same time. If you activate Digital TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be automatically turned “OFF”.

Page 71

S-VHS

OFF

* The default setting is

Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.

To record in S-VHS:

●

Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front display panel. The S-VHS recording mode is selected.

To record in S-VHS ET on a VHS cassette:

●

See “Super VHS ET (S-VHS ET)” on page 29.

To record in VHS:

●

Insert a cassette marked “VHS”. If the S-VHS ET indicator on the recorder’s front panel is lit and the S-VHS ET mode is activated, press S-VHS ET indicator goes off. The VHS recording mode is automatically selected regardless of the “S-VHS” mode setting.

To record in VHS on an S-VHS cassette:

●

Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off. The VHS recording mode is selected.

in the table below.

bold

S-VHS ET

. The

NOTE:

When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS indicator lights up on the front display panel regardless of the “S-VHS” mode setting.

COLOUR SYSTEM

PAL/NTSC

MESECAM

TIME SCAN AUDIO

OFF

: To record PAL signals, or play back a

: To record SECAM signals, or play

PAL or NTSC tape.

back a MESECAM tape.

You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals on this recorder. Select the appropriate colour system.

* SECAM signals will be recorded as MESECAM on this recorder;

MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video cassette recorder.

NOTES:

●

It is not possible to record in S-VHS if “MESECAM” is selected. The recording mode is forced to change to VHS.

●

If “MESECAM” is selected when the tape speed is set to EP mode, the tape speed will be forced to change to LP mode.

●

It is not possible to select EP mode if “MESECAM” is selected.

About NTSC Playback

●

Some TVs shrink the picture vertically and place black bars at the top and bottom of the TV screen. This is not a malfunction on the part of either the video recorder or the TV.

●

The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

●

The counter and tape remaining time readings will be incorrect.

●

During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

●

Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

When this function is set to “ON”, you can hear the sound during TimeScan. (

墌

pg. 24)

Page 72

Tuner Set

Turn on the TV and select the video channel (or AV mode).

SUBSIDIARY SETTINGS (cont.)

IMPORTANT

Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up or by Preset Download ( — you have moved to a different area or if a new station starts broadcasting in your area.

Your recorder needs to memorize all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR buttons without going through any vacant channels.

pg. 12, 14).

墌

Auto Channel Set

Turn on the recorder.

Press 1.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press

Access the Auto Channel Set screen.

Select your country.

Press rt to move the highlight bar (pointer) to your country’s name, then press OK or

Select the language.

Press rt to move the highlight bar (pointer) to the language of your choice.

Page 73

IMPORTANT

Beginning End

●

In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S

HOWVIEW

programme of a different station. When programming the timer using the S desired channel is selected correctly ( “S

HOWVIEW

●

Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture ( A Channel”).

system, the recorder will record a TV

HOWVIEW

Timer Programming”).

system, be sure to check the

pg. 32,

墌

pg. 75, “Delete

墌

NOTES:

●

Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 76.

●

If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

●

If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (

pg. 75, “INFORMATION”).

墌

Perform Auto Channel Set.

Press OK twice.

●

If you have connected the recorder and your TV via AV connection ( recorder automatically performs the Preset Download and the T-V LINK screen will appear (

pg. 14).

墌

●

The Auto Set screen appears, and remains on screen while the recorder searches for receivable stations. As Auto Channel Set progresses, the “ moves from left to right. Wait until the TV screen as shown in step 7 appears.

View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen — channel positions (PR), channels (CH) and station names (ID – blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the button on the remote control.

●

The stations located in the selected country appear at the top of the list.

●

The Guide Program numbers will also be set automatically during Auto Channel Set.

Return to the normal screen.

Press

●

Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 74 – 76 for the procedures.

●

Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●

For information on scrambled broadcasts, refer to page 75.

pg. 10), the

墌

q” mark on the TV screen

pg. 77). The

墌

rt w e

Page 74

Manual Channel Set

Store channels that were not stored during Auto Set Up (

pg. 12), Preset Download (墌pg. 14) or Auto Channel Set

墌

(

pg. 72).

墌

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or Confirmation screen appears.

Access the Confirmation screen.

. The

SUBSIDIARY SETTINGS (cont.)

Select the band.

Press rt to change the band between CH (regular) and CC (cable), then press e.

Input the channel.

Press the want to store.

●

Press OK and the Confirmation screen appears.

●

Press

●

number keys

Input “0” before any single number entries. To input the registered station name (ID – until “– – – –” (ID setting) begins blinking, then press For fine tuning adjustment, press then press When storing a channel that sends scrambled broadcasts, press set “DECODER” to “ON” (“OFF” is the default setting). When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER” setting cannot be changed (

rt. While tuning, “+” or “–” appears.

e until “OFF” (Decoder setting) blinks, then press rt to

Enter new channel information.

Repeat steps 3 – 6 as necessary.

Close the Confirmation screen.

To change positions, see “Change Station Channel Position” (

pg. 75).

墌

If you wish to set station names other than the ones registered in your recorder, see “Set Stations (B)” (

to input the channel number you

pg. 77), press e

墌

e until “+/–” begins blinking,

pg. 53).

墌

pg. 76).

墌

rt.

Select the channel position.

Press rt w e until an open position in which you want to store a channel begins blinking, then press OK. The Manual Channel Set screen appears.

(Example) To store in position 12.

The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each.

ATT E NT I O N

Guide Program numbers are not set when channels are stored manually. If an attempt is made at timer programming with the S SET” screen appears; set the Guide Program numbers on this screen. ( Number Set”) Or perform “Guide Program Number Set” (

HOWVIEW

墌

system in this state, the “GUIDE PROG

pg. 33, “ATTENTION — Guide Program

pg. 79).

墌

Page 75

Delete A Channel

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

Select the item.

Press rt w e until the item you want to delete begins blinking.

Delete a channel.

Press &.

●

The item directly beneath the cancelled one moves up one line.

●

Repeat steps 1 and 2 as necessary.

Close the Confirmation screen.

Press

Change Station Channel Position

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

Select the item.

Press rt w e until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking.

When Receiving A Scrambled Broadcast

Select the decoder mode.

Set “L-2 SELECT” to “DECODER” (墌pg. 53).

Access the Confirmation screen.

Perform steps 1 and 2 of “Manual Channel Set” on page 74.

Select the position.

Press rt w e to select the channel position broadcasting scrambled programmes, then press OK twice

Change the decoder setting.

Press e until “OFF” (decoder setting) begins blinking, and set it to “ON” by pressing

Return to the Confirmation screen.

Press OK.

●

Repeat steps 3 – 5 as necessary.

Close the Confirmation screen.

Press

Select the new position.

Press rt w e to move the station to the new channel position, then press OK.

Example: If you moved the station in position 4 to position 2, the

●

Press

stations originally in positions 2 and 3 each move down one space.

Repeat steps 1 and 2 as necessary.

Close the Confirmation screen.

INFORMATION

If you live in Eastern Europe, “TV SYSTEM” setting appears instead of “DECODER” setting on the Manual Channel Set screen. When you can see the picture but can hear no audio, select appropriate TV system (D/K or B/G). Normally, TV programmes are broadcasted as follows. For Eastern Europe : D/K For Western Europe : B/G

A Select a country in Eastern Europe in step 4 on page 72. B Press

C Press

e until the TV system (D/K or B/G) blinking on the

Manual Channel Set screen in step 4 on page 74.

rt to select appropriate TV System (D/K or B/G).

Page 76

SUBSIDIARY SETTINGS (cont.)

Set Stations (A)

Set station names that are registered in your recorder.

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

Select the item.

Press rt w e until the item you want begins blinking.

Access the Manual Channel Set screen.

Press OK twice.

Select the new station.

Press e until the station name (ID) begins blinking, then press rt until the new station’s name (ID) you want to store begins blinking. Registered station names (

pg. 77) appear as you

墌

press

Press OK.

●

Press

Switch the stations.

The Confirmation screen appears. Repeat steps 1 – 4 as necessary.

Close the Confirmation screen.

Set Stations (B)

Set station names other than the ones registered in your recorder.

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen and then perform steps 1 and 2 of “Set Stations (A)” above before continuing.

Select the character for station name.

Press e until the first letter of the station name begins blinking.

Enter the new character.

Press rt to cycle through the characters (A–Z, 0–9, –, f, +,

(space) ) and stop when the desired character is

indicated, then press characters the same way (maximum of 4). After entering all characters, press OK.

●

The Confirmation screen appears.

●

If you make a mistake, press begins blinking. Then enter the correct character by pressing

rt.

Close the Confirmation screen.

Press

to enter. Enter the remaining

w until the incorrect character

NOTE:

The characters available for the station name (ID) are A–Z, 0–9, – ,

f, +, I (space) (maximum of 4).

Fine-Tuning Channels Already Stored

Perform steps 1 and 2 of “Manual Channel Set” on page 74 to access the Confirmation screen before continuing.

Select the channel to fine-tune.

Press rt w e until the channel you want to tune begins blinking.

Access the Manual Channel Set screen.

Press OK twice. The Manual Channel Set screen appears.

Perform tuning.

Press e until “+/–” begins blinking, then press rt until the picture is its clearest. Then press OK.

●

The Confirmation screen appears.

●

Repeat steps 1 – 3 as necessary.

Close the Confirmation screen.

Press

Page 77

TV Station And ID List

ID* STATION NAME

1000 3SAT ADLT ANT3 ARD ARTE BBC BBC1 BBC2 BR3 C+ C1 CAN5 CANV CH4 CH5 CHLD CINE CLUB CMT CNN CSUR DISC DR DRS DSF ETB1 ETB2 EURO EUSP FEMM FILM FNET FR2 FR3 GALA HR3 INFO ITA1 ITA7 ITV JSTV KA2 KAB1 KAN2 LOCA M6 MBC MCM MDR MOVE MTV MTV3 N3 N-TV NBC NDR3 NED1 NED2 NED3 NEWS NICK NRK NRK2 ODE ORF1 ORF2

TV1000 3SAT ADULT ANTENA3 ARD ARTE BBC GROUP BBC1 BBC2 BAYERN3 CANAL PLUS PORTUGUSES CANALE5 KETNET CANVAS CHANNEL4 CHANNEL5 CHILD CINEMA TELECLUB CMT CNN ANDALUCIA DISCOVERY DR TV DRS DSF ETB1 ETB2 EURONEWS EUROSPORTS FEMMAN FILM FILMNET France2 France3 GALAVISION HESSEN3 INFO-KANAL ITALIA1 ITALIA7 ITV JSTV KA2 KABEL1 KANAL2 LOCAL M6 MBR MCM MDR MOVIE MTV MTV3 NORD3 N-TV NBC SUPER NDR NED1 NED2 NED3

NICKELODEON NRK NRK2 ODEON ORF1 ORF2

ID* STATION NAME

ORF3 OWL3 PREM PRO7 RAI1 RAI2 RAI3 RET4 21 RTBF RTL RTL2 RTL4 RTL5 RTP S4 SAT1 SBS SHOW SIC SKY SKYN SPRT SRTL STAR SVT1 SVT2 SWR TCC TELE TEL5 TF1 TM3 TMC TNT TRT TSI TSR TV1 TV2 TV3 TV4 TV5 TV6 TVE1 TVE2 TVG TVI TVN VCR VERO VH-1 VIVA VIV2 VMTV VOX VT4 VTM WDR1 WDR3 YLE1 YLE2 ZDF ZTV

* The “ID” abbreviation is what is shown on-screen in lieu of the station

name. The “ID” abbreviation is listed in the Confirmation screen and is displayed on the TV screen when the recorder is tuned to a different station.

ORF3 OWL3 PREMIERE PRO7 RAI1 RAI2 RAI3 RETE4 TELE21 RTBF1 or 2 RTL RTL2 RTL4 RTL5 RTP SCHWEIZ4 SAT1 SBS SHOW SOCIEDADE SKY CHANNEL SKY NEWS SPORT SUPER RTL STAR-TV SVT1 SVT2 SUEDWEST3 TCC TELE TELE5 TF1 TM3 TELEMONTECARLO TNT INT TRT INT TSI TSR BRTN TV1 TV2 TV3 TV4 TV5 TV6 TVE1 TVE2 TV GALICIA TV INDEPENDENT TV NORGE VIDEO VERONICA VH-1 VIVA VIVA2 VIDEO MUSIC VOX VT4 VTM West1 West3 YLE1 YLE2 ZDF ZTV

Page 78

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

— interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area. — you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

If you have connected the recorder to your TV via the AV or S-VIDEO connection (墌pg. 10, 11), since you do not need the video channel you have to set the video channel to off. If you have connected the recorder to your TV via the RF connection ( channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

Then set your TV to UHF channel 50.

●

Access the Video Channel Set mode.

Hold down panel shows the following.

on the recorder until the front display

If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●

If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

pg. 10), you have to set the correct video

墌

Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●

If you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER EASTERN EUROPE (EE) for the country setting ( press

rt to set to “2”.

●

For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Set the video channel.

With AV or S-VIDEO Connection

Press (or “2OUT– –”).

●

Now the video channel is set to off.

With RF Connection

Press channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

until the front display panel shows “1OUT– –”

PR –

or – to set the video recorder to a vacant

PR +

pg. 12, 16),

墌

NOTES:

●

If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●

If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

Exit the Video Channel Set mode.

Press OK on the remote control.

With AV or S-VIDEO Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel. To view picture signals from the video recorder, set your TV to the video channel.

Page 79

HOWVIEW

System Setup

IMPORTANT

Normally, Auto Set Up (墌pg. 12), Preset Download (墌pg. 14) or Auto Channel Set (墌pg. 72) sets the Guide Program numbers automatically. You need to set the Guide Program numbers manually only in the following cases.

●

When timer-programming with the S your recorder, is not selected,

when you add a channel after Auto Set Up, Preset Download or Auto Channel Set has taken place, —Set the Guide Program number for that station manually.

●

When you wish to timer-record a satellite programme with the S —Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver.

Turn on the TV and select the video channel (or AV mode).

HOWVIEW

system, the channel position, where the station you wish to record is received on

HOWVIEW

system,

Guide Program Number Set

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or

Press rt to move the highlight bar (pointer) to “GUIDE PROG SET”, then press OK or

Press rt to enter the Guide Program number for the desired station as shown in the TV listings. Then press OK or

Access the Initial Set screen.

Access the Guide Program Set screen.

Enter the Guide Program number.

(Example) When inputting the

Guide Program number 2 for ZDF.

Enter the receiving channel position number.

Press the select “TV PROG” or “SAT”. Then press number of the recorder’s channel position on which the Guide Program number’s broadcast is received by the recorder or the satellite receiver. Then press OK or

●

Press

number key “0

to input the

To timer-record a satellite programme with the S system, you need to install the provided Satellite Controller and perform the procedure described in “Satellite Receiver Control Setting” ( Repeat steps 4 and 5 as necessary.

墌

pg. 17).

Return to the normal screen.

” to

HOWVIEW

(Example) If ZDF is received on

channel position 2.

Guide Program Number

“Guide Program (GUIDE PROG) number” refers to the assigned TV station numbers, according to broadcast area, for the S

HOWVIEW

numbers can be found in most TV listings.

timer recording. The Guide Program

Page 80

Clock Set

Turn on the TV and select the video channel (or AV mode).

SUBSIDIARY SETTINGS (cont.)

IMPORTANT

If you performed Auto Set Up (墌pg. 12), Preset Download (

pg. 14) or Auto Channel Set (墌pg. 72), without ever

墌

having set the clock previously, the recorder’s built-in clock is also set automatically. Perform the following steps only if — —Auto Clock Set has not been performed correctly by Auto Set Up, Preset Download or Auto Channel Set.

—the recorder’s memory backup has expired.

—you want to change Just Clock setting ( the left column).

Turn on the recorder.

Press 1.

Access the Main Menu screen.

Press

Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or

Access the Initial Set screen.

“Just Clock” in

墌

Just Clock

The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set “ON” or “OFF” at the Clock Set screen (the default setting is “OFF”). Press OK until the Just Clock setting begins blinking, then press the setting.

IMPORTANT:

recorder’s built-in clock may be reduced, which could adversely effect timer recording. We recommend you to keep Just Clock on. In cases where the clock setting data from a PDC signal is incorrect, however, you are advised to keep Just Clock set to “OFF”.

If you turn off Just Clock, the accuracy of your

rt to change

Access the Clock Set screen.

Press rt to move the highlight bar (pointer) to “CLOCK SET”, then press OK or

. The Clock Set screen appears.

NOTE:

When you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48), РОССИЯ (07) or OTHER EASTERN EUROPE (EE) for the country setting ( you cannot use Just Clock function. Skip steps 6 and 7 on page 81.

pg. 12, 16),

墌

Page 81

Set the date and time.

Press rt to set the time, then press OK or e. The “DATE” display begins blinking. Repeat the same procedure to set the date and year.

●

When you set the time, press and hold by 30 minutes.

●

When you set the date, press and hold by 15 days.

Set Just Clock.

The default setting is “OFF”. Set as desired by pressing

, then press OK or e.

●

For the Just clock function, refer to “Just Clock” on page 80.

●

If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjustments.

Set the source channel position for clock

rt to change the time

rt to change the date

data.

The recorder is preset to receive clock setting and adjustment data from channel position 1. Press rt to set the channel position to the number representing the station transmitting clock setting data, then press OK or e.

Start the clock operation.

Press

NOTES:

●

Just Clock (when set to “ON”) adjusts the recorder’s built-in clock every hour, except for 23:00, 0:00, 1:00 and 2:00.

●

Just Clock is not effective when ... ... the recorder’s power is on. ... the recorder is in the Timer mode. ... a difference of more than 3 minutes exists between the built-in clock’s time and the actual time. ... the recorder is in the Automatic Satellite Programme Recording mode ( ... the recorder is in the Power Save mode ( ... “L-2 SELECT” is set to “SAT” (

●

If Just Clock is set to “ON”, the recorder’s clock is automatically adjusted at the start/end of Summer Time.

●

Just Clock may not function properly depending on the reception condition.

墌

pg. 38).

墌

pg. 53).

墌

pg. 70).

Page 82

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. No power is supplied to the recorder.

2. The clock is functioning properly, but the recorder cannot be powered.

3. The remote control won’t function.

●

The mains power cord is disconnected. Connect the mains power cord.

●

“

#” is displayed on the front display

panel with “AUTO TIMER” set to “OFF”.

●

The batteries are discharged. Replace the dead batteries with new ones.

Press the # button to turn the “#” indicator off.

TAP E T RA N SP OR T

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

●

“

1. The tape does not run during recording.

2. The tape will not rewind or fast-forward.

” is displayed on the front display

panel.

●

The tape is already fully rewound or fast-forwarded.

Press 4 to turn the “i” indicator off.

Check the cassette.

PLAYBACK

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. The playback picture does not appear while the tape is running.

2. Noise appears during visual search.

3. Noise appears during normal playback.

4. The playback picture is blurred or interrupted while TV broadcasts are clear or “USE CLEANING CASSETTE” message appears on the screen.

5. Breaks are noticeable in Hi-Fi soundtrack.

●

If you are using the RF connection, . . . the TV receiver’s channel selector is not set to the video channel. . . . the recorder’s video channel has not been correctly set.

●

If you are using the AV or S-VIDEO connection, the TV receiver is not set to the AV mode.

●

This is normal during visual search other than TimeScan.

●

The automatic tracking mode is engaged.

●

The video heads may be dirty. Use a dry cleaning cassette TCL-2UX or

●

The automatic tracking mode is engaged.

If you are using the RF connection, . . . set the TV receiver to the video channel. . . . perform “Video Channel Set” (

pg. 78).

墌

If you are using the AV or S-VIDEO connection, set the TV to its AV mode.

Try manual tracking. (

consult your JVC dealer.

Try manual tracking. (

墌

pg. 23)

Page 83

RECORDING

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Recording cannot be started.

2. TV broadcasts cannot be recorded.

3. Tape-to-tape editing is not possible.

4. Camcorder recording is not possible.

TIMER RECORDING

SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION

1. Timer recording won’t work.

2. Timer programming is not possible.

3. “

#” and “[” on the front display

panel won’t stop blinking.

4. The power shuts off and “ “

[” on the front display panel won’t

stop blinking.

5. “

#” blinks for 10 seconds and the

Timer mode is disengaged.

6. The S

HOWVIEW

timer-record properly.

system does not

#” and

●

There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

●

“L-1”, “L-2”, “F-1”, “S-1” or “SAT” has been selected as the input mode.

●

The source (another video recorder, camcorder) has not been properly connected.

●

All necessary power switches have not been turned on.

●

The input mode is not correct. Set the input mode to “L-1”, “L-2”, “F-1”

●

The camcorder has not been properly connected.

●

The input mode is not correct. Set the input mode to “L-1”, “L-2”, “F-1”

●

The clock and/or the timer have been set incorrectly.

●

The timer is not engaged. Press

●

Timer recording is in progress. Timer programming can’t be performed

●

The timer is engaged but there’s no cassette loaded.

●

The loaded cassette has had its record safety tab removed.

●

The end of the tape was reached during timer recording.

●

# has been pressed when there are no

programs in memory, or the timer record information has been programmed incorrectly.

●

The recorder’s channel positions have been set incorrectly.

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired channel.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

or “S-1”.

Confirm that the camcorder is properly connected.

or “S-1”.

Re-perform the clock and/or timer settings.

# and confirm that “#” is

displayed on the front display panel.

while a timer recording is in progress. Wait until it finishes.

Load a cassette with the record safety tab intact, or cover the hole using adhesive tape.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

Check the programmed data and re-program as necessary, then press again.

Refer to “Guide Program Number Set” (

pg. 79) and re-perform the procedure.

墌

Page 84