iRobot Verro 600 User Manual
iRobot® Verro
OWNER’S MANUAL
Model 600
™
Safety Notes
WARNING: Your cleaner should not be used while people are swimming
in the pool.
A Ground Fault Current Interrupter (GFCI) must be installed to protect
your electric outlet and prevent any possible electric shock. The unit
must be supplied through a Ground Fault Current Interrupter outlet.
The connection to the branch circuit should be consistent with the local
and national wiring rules (electrical code).
If the supply cord is damaged, it must be replaced by the
manufacturer’s service agent or a qualified and trained person in order
to avoid hazards.
Always remember to turn the Power Supply OFF and unplug it from the
power outlet before removing the cleaner from the pool.
Shut off and unplug the Power Supply every time you remove the
cleaner from the water.
Do not leave the cleaner in the pool all the time.
Mishandling the unit can result in leakage of lubricants.
Please keep the plug away from contact with water.
2 iRobot Verro Owner’s Manual
Cautions
Please read this manual completely before operating your pool cleaner.
Retain the safety and operating instructions for future reference.
Do not switch the pool cleaner ON if it is not fully immersed in
water. Operating the cleaner out of water will cause severe damage
immediately and will result in loss of warranty.
Allow the cleaner to remain in the pool for 15 to 20 minutes following
the end of its cleaning cycle. This will allow the motors to cool
adequately.
Do not use Verro in a pool warmer than 100 degrees Fahrenheit.
Do not use the floating power cord to lift Verro from the pool. Use the
handle.
Do not force the floating power cord plug. It will fit into the socket only
one way.
The floating power cord must be locked in the socket on the Power
Supply.
Do not leave your cleaner in direct sunlight when not in use.
Never leave the Power Supply in direct sunlight and avoid leaving it in
the rain.
www.irobot.com 3
Tips
Tip
Clean the filter bag regularly. Verro uses the force of the water pumped through its filter bag
to maintain traction, particularly on the walls of the pool. If the filter bag is not kept clean,
Verro will not clean properly and will not be able to climb the walls of the pool.
Tip
Change the direction of the handle before each cleaning run to prevent the floating power
cord from becoming twisted and to improve coverage of the entire pool. (p. 8)
Tip
Store Verro in a dry place out of direct sunlight at a temperature between 50 and 104
degrees Fahrenheit. The Power Supply is water resistant, but not waterproof and may be
damaged by rain. Important: Failure to properly store Verro will result in loss of warranty.
Tip
iRobot recommends using the mesh filter bag (available separately at www.irobot.com)
when the pool contains a significant quantity of large debris (leaves, etc.), such as when
the pool is opened for the season. The fine filter bag is ideal for filtering small debris
(algae, sand, etc.) and for regular maintenance.
Tip
Periodically straighten the floating power cord with the Detangler.
4 iRobot Verro Owner’s Manual
Table of Contents
Anatomy ..................................................................... 6
Parts List .................................................................... 7
Using Verro ................................................................. 8 - 10
How Verro Works ......................................................... 11
Cleaning the Filter Bag ................................................. 12 - 13
Maintenance and Adjustment ....................................... 14 - 18
Troubleshooting ........................................................... 19 - 20
Customer Care ............................................................ 21
www.irobot.com 5
Anatomy
1
15
4
2
3
14
8
10
7
5
6
9
23
13
6 iRobot Verro Owner’s Manual
18
11
12
16
17
19
20
21
22
24
Parts List
1. Outlet Top
2. Pump Motor
3. Drive Motor
4. Handle Lock Mechanism
5. Pulley Assembly
6. Drive Belt
7. Drive Track
8. Body Assembly
9
. Filter Screen
10. Side Plate
11. PVA Brush
12. Filter Bag
13. Bottom Lid Assembly
14. Handle Assembly
15. Cable Assembly
16. Power Supply (Transformer)
1 .
17. Transformer Socket
8 Wheel Tube Assembly
19. OFF button
20. Light
21. ON button
22. Power Cord (Outlet)
23. Vacuum Intake Flaps
24. Lock Tabs
www.irobot.com 7
3.5m/12
ft
Using Verro
Position the handle diagonally across Verro. Each time Verro cleans the pool, reverse the
1
direction of the handle. This will help keep Verro from twisting the floating power cord and
ensure more even coverage.
Uncoil the floating power cord and spread it over the surface of the water.
2
Place Verro in the water and rock it from side to side to allow air to escape.
3
Let Verro settle to the bottom of the pool. Ensure that it is right side up and level.
Place the Power Supply (transformer) at least 3.5 meters /12 feet from the pool.
4
8 iRobot Verro Owner’s Manual
Loading...