Invacare Corporation
www.invacare.com
USA
One Invacare Way
Elyria, Ohio
44035-4190
(800) 333-6900
Canada
570 Matheson Blvd. E.
Unit 8
Mississauga, Ontario
L4Z 4G4 Canada
(800) 668-5324
Invacare, the blue medallion
design and Infinity are registered trademarks and Yes,
you can., Compass, GT and
Personal Back10 are trademarks of Invacare
Corporation. Specifications
are subject to change without notification.
© 2004
Invacare Corporation
Form No. 04-154
‘‘Invacare says ‘Yes, you
can,
™
’ and I couldn’t have
said it better myself.’’
Knee-to-heel*
Folding frames w/ seat rails min max
60˚ 13.50
"
17.50"
60˚ MFX 9
"
12.50
"
70˚ 13.50" 16.50"
70˚ MFX 12.75
"
16.25"
70˚ Tapered 5.75
"
11.75
"
Elevating 14
"
20
"
90˚ 4.50
"
7.50
"
* Range adjusts in 1" increments. Measurement taken from top of seat rail to back of
footrest.
Arm heights*
AT99N* 6.50" - 12.50"
AT55D* 8" - 14"
AT55F* 8" - 14"
TAD** Low Range 8" - 12"
TAF** High Range 10" - 16"
* Range adjusts in 1" increments. ** Range adjusts in 0.5" increments.
All measurements from top of seat rail to top of armrest. On AT55D and AT55F, add 1"
for upholstered arm pads. For less-seat-rail chairs, add 1.5" to above measurements (top of
upper frame rail to top of ar mrest.)
Spree GT Specifications*
Seat width 12"-16"
Seat depth 12"-16"
Overall chair width Seat width plus 8.50"
Back height 20" and 24"
Adjustable angle back 0˚, 10˚,20˚, 30˚
Camber angles 0˚
Tubing outside diameter 1" frame,1" seat rail
Weight of chair 26 lb.** / 38 lb.***
Weight capacity 200 lb.
Limited warranty Lifetime on frames and crossbraces
* 0º Angle
** 18”x 16”, AT902, no rear wheels, no footrests, no anti-tippers, no wheel locks, no arms.
*** 18” x 16”, AT902, 24SP, PNEU, 70NTAPER, seat upholstery, back upholstery, wheel locks, no
arms.
Seat-to-floor-heights*
Caster 4" 4" 6" 6"
5ALUM
4SPLT 5SOFT AT902 1259
16.00
" 16.00" 16.00" 16.00"
12" Rear Wheel
16
.50
"16
.50
" 16.50"
17
.50
" 17.00" 17.50"
18"
14.50
" 14.50" 15.50" 16"
18" Rear Wheel 15
" 15" 16"
15.50" 15.50"
16
" 16"
15" 15" 15.50" 16"
20" Rear Wheel 15.50
" 15.50" 16" 16.50"
16" 16" 16.50"
17"
16" 16" 16" 16"
22"
Rear Wheel
16.50" 16.50" 16.50"
17" 17.50"
18"
n/a n/a 17" 18.50"
24"
Rear Wheel
18"
Invacare
®
Spree GT Wheelchair
Invacare
®
Spree GT
Wheelchair
ANSI/RESNA W/C19 sec 6.2 Presale Literature Notification - Spree GT
A.
Minimum turning radius 20.50".
Minimum turn-around width 32.41".
(14x14 SDR1216 Medium Frame chair without footrests).
B. Spree GT wheelchairs equipped with vent trays may be longer than 1220 mm, exceeding the ADA definition of a common wheelchair and the
minimum length requirements of lifts on public vehicles, and may therefore present particular difficulties accessing some vehicles.
C. Total wheelchair mass = 42.0 lb (19.0 kg) – including front riggings, anti-tips, tie-down brackets. Does not include wheel locks, wheelchair-
anchored pelvic belt, and seating.
D. Average lateral dummy displacement = approximately 0.51" (13 mm).
E. Overall Score = 17.
Overall Rating = A.
F. i . The Spree GT was sized to accommodate a 170 lb. test dummy. (Medium Frame, 18" W x 18D", 60 degree front rigging, 20" composite
wheels, 24" urethane tires, aluminum seat pan cushion, Invacare
®
Personal Back™10 seat system, 6x2" semi-pneumatic casters.)
ii. The Spree GT tested was tied down using four tie-down brackets - 2 brackets located near the front of the seat frame and 2 brackets
located on the rear of base frame.
iii. The Spree GT was tested with a 170 lb. test dummy.
iv. The Spree GT tested used a wheelchair-anchored pelvic belt and vehicle-anchored shoulder belt.
v. The Spree GT tested complies with the performance requirements of ANSI/RESNA W/C19 sec 5.3.
G. For all types of vehicles, the Spree GT requires four SAE J2249-compliant tie-down strap assemblies for effective securement.
H. When the TRO or TRBKTS option is selected, the Spree GT provides a location for anchoring of an Invacare-provided pelvic belt.
This belt has been tested in accordance with ANSI/RESNA W/C19.
I. The wheelchair-anchored pelvic belt is supplied by Invacare.