Intermec CK70, CK70NI, CN70, CN70NI, CN70e User Manual

DRAFT

70 Series

Mobile Computer

CK70, CK70NI, CK71, CK71NI, CN70, CN70NI, CN70e, CN70eNI,

CK70 RFID, CN70e RFID, CN70 RFID

User Manual

DRAFT

Intermec Technologies Corporation

Worldwide Headquarters
6001 36th Ave.W.
Everett, WA 98203
U.S.A.

www.intermec.com

The information contained herein is provided solely for the purpose of allowing customers to
operate and service Intermec-manufactured equipment and is not to be released, reproduced, or
used for any other purpose without written permission of Intermec Technologies Corporation.

Information and specifications contained in this document are subject to change without prior
notice and do not represent a commitment on the part of Intermec Technologies Corporation.

© 2011–2013 by Intermec Technologies Corporation. All rights reserved.

The word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook, CrossBar,
dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, i-gistics, INCA (under license),
Intellitag, Intellitag Gen2, JANUS, LabelShop, MobileLAN, Picolink, Ready-to-Work, RoutePower,
Sabre, ScanPlus, ShopScan, Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares,
and Vista Powered are either trademarks or registered trademarks of Intermec Technologies
Corporation.

There are U.S. and foreign patents as well as U.S. and foreign patents pending.

Wi-Fi is a registered certification mark of the Wi-Fi Alliance.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation
in the United States and/or other countries.

Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.

ii 70 Series Mobile Computer User Manual

DRAFT

Document Change Record

This page records changes to this document. The document was
originally released as Revision 001.

Version
Number

006 01/2013 Added information to support Intermec RFID

005 11/2012 Added information to support firmware version

004 2/2012 Revised information on ScanNGo bar codes.

003 12/2011 Added information on:

Date Description of Change

standalone demonstration application for these
mobile computers: CK70 RFID, CN70e RFID, and
CN70 RFID.

1.50:

• CloneNGo application

• New camera settings

• SceneEditor application

• EA30 imager extended reading range

• the flashlight feature.

• the Carrier Selection application.

Revised information on:

• the Intermec Settings menus.

• upgrading the system software and the

operating system.

• GPS procedures.

• ScanNGo bar codes.

002 06/2011 Revised to add information on

70 Series Mobile Computer User Manual iii

non-incendive (NI) versions of the computer,
provisioning the computer, the new
ScanDiagnostics application, and how to use the 70
Series as a USB mass storage device. Also corrected
the cold boot procedure and removed the compass.

DRAFT

1

About the Computer Features

This chapter introduces the 70 Series Mobile Computers with
Windows® Embedded Handheld operating system. Use this
chapter to learn about the basic features and functions of each
computer, as well as the available accessories for it.

1

DRAFT

Chapter 1 — About the Computer Features

Scan button

On/o button

Microphone

Cell phone speaker

Good read LED

Battery status LED

About the 70 Series Mobile Computers

The ergonomically designed Intermec 70 Series Mobile Computers are
built on the Microsoft Windows Embedded Handheld operating
system. They are lightweight, easy-to-use, and run most software
developed for the Windows Embedded platform, including
standalone, client-server, and browser-based applications.

The 70 Series family of computers consists of four different models:
the CN70, CN70e, CK70 and CK71. The CN70 and CN70e have the
same features except that the CN70e offers a larger keypad for
data-input intensive applications. The CK70 and CK71 have most of
the same features, but the CK71 offers a choice of imager options and
does not offer a WWAN radio option (phone). For hazardous
environments, Intermec offers non-incendive (NI) models of each 70
Series computer. Throughout this manual, all versions of the mobile
computer are referred to as 70 Series unless information is specific to
a particular model of computer.

In most of the user manual, pictures of the CN70 and CK70 represent
the four models of the 70 Series computers. The Intermec RFID Demo
IM11 handheld computers (CK70 RFID, CN70e RFID, and CN70
RFID) have a visual RFID label indicated on the Front View.

CN70 Front View

2 70 Series Mobile Computer User Manual

DRAFT

CN70 Back View

IrDa port

Speaker port

Imager

Camera

Battery

Scan button

Microphone

On/o button

Cell phone speaker

Notification LED

Good read LED

Battery status LED

Chapter 1 — About the Computer Features

CK70 and CK71 Front View

70 Series Mobile Computer User Manual 3

DRAFT

Chapter 1 — About the Computer Features

CK70 and CK71 Back View

Imager

Camera

Imager

Camera

Battery

What’s New in This Release

This version of the user manual supports the following new features:

• Intermec 70 Series RFID Demo IM11 application allows users to

read and write RFID tags without the use of an outside application
such as Notepad or Excel. For more information, see “About

Intermec 70 Series RFID Demo” on page 48.

Left speaker
port

IrDA port

Battery

Left speaker
port

IrDA port

Overview of 70 Series Features

The 70 Series includes these standard features:

• EA30 area imager that can read bar codes and capture images

• (CK71 only) Choice of EA30, EX25, or EV12 imagers

• Multi-processor architecture with 512 MB DRAM and 1G Flash

• CDMA, UMTS, or Flexible Network Radio capability (not available

on CK71)

• 802.11a/b/g/n and Bluetooth® radios

• GPS radio on CDMA, UMTS, or Flexible Network Radio

computers (not available on CK71)

4 70 Series Mobile Computer User Manual

DRAFT

• 5-megapixel auto-focus color camera

• Customer-accessible microSD slot for memory cards up to 32 GB

• Customer-accessible SIM card slot

• IrDA port with speeds up to 4 Mbps

• Intermec RFID Demo (models: CK70 RFID, CN70e RFID, and

CN70 RFID) integrated with UHF reader allows users to scan and

write data to RFID tags

The 70 Series Mobile Computer with an IEEE 802.11a/b/g/n
radio installed is Wi-Fi® certified for interoperability with
other 802.11a/b/g/n wireless LAN devices.

About the Status LEDs

Use the following illustrations and table to understand the status
LEDs on your computer. All six status LEDS are not available on every
70 Series computer. For example, the QWERTY versions of the CN70
and CN70e do not have a Green key status LED.

Chapter 1 — About the Computer Features

Location of the CN70 Status LEDs

Good Read and Ready-to-Work
Status LED

Notification LED

Orange key
status LED

Shift key
status LED

Battery status LED

Green key
status LED

70 Series Mobile Computer User Manual 5

DRAFT

Chapter 1 — About the Computer Features

Green key
status LED

Shift key status LED
(CK70 alphanumeric
and CK71 function numeric)

Shift key status LED
(CK70 numeric and
CK71 alphanumeric)

Orange key
status LED

Notification LED

Good Read and Ready-to-Work
status LED

Battery status LED

Location of the CK70 and CK71 Status LEDs

Status LED Descriptions

6 70 Series Mobile Computer User Manual

LED Color Description

Notification Amber This LED is user-programmable.

Good Read Green The computer successfully decoded a bar code or

an RFID tag.

Ready-to-Work Blue If you have Intermec Terminal Emulator (ITE),

Battery See “About Battery Status” on page 13.

Blinking
blue

Off ITE is not installed or not running.

the application is running and connected to the
host.

If you do not have ITE, you can configure the
Ready-to-Work indicator to turn on or off to
indicate a healthy state.

ITE is running but not connected to the host.
The computer is unhealthy.

The computer is healthy.

DRAFT

LED Color Description

Key Status Green The Green function key is enabled.

Orange The Orange function key is enabled.

Shift Red The Shift key is enabled.

70 Series Accessories

The 70 Series computer ships with a battery. All other accessories are
sold and ordered separately. For help, contact your local Intermec sales
representative.

Chapter 1 — About the Computer Features

When writing RFID tags, a Good Read LED will
blink on Green if a write is successful.

When writing RFID tags, the Battery Status LED
will turn on Red for 1 second and then return to
its previous state if a write is unsuccessful.

70 Series Accessories

Accessory Description

Audio Snap-On Adapter Use the audio adapter to connect the

computer to a headset.

Back Accessory Interface Use the back accessory interface to attach

accessories such as the magstripe reader
adapter to the CK70 and CK71.

CK70/CK71 Battery This battery provides main power to the

CK70 and CK71.

CK70/CK71 Magstripe Reader
Adapter

CN70/CN70e Battery This battery provides main power to the

CN70/CN70e Magstripe Reader
Snap-On Adapter

Desktop Stand Use the desktop stand to hold the 70

Use the magnetic stripe reader to be able
to read magnetic cards with the CK70 and
CK71 computer.

CN70 and CN70e.

Use the magnetic stripe reader to be able
to read magnetic cards with the CN70
and CN70e computer.

Series computer on your desk or a stable
surface.

70 Series Mobile Computer User Manual 7

DRAFT

Chapter 1 — About the Computer Features

Accessory Description

DEX/UCS Snap-On Adapter Use this adapter to receive and send serial

communications through a DEX/UCS
connection.

DX1 Desktop Dock with USB
connectivity

DX2 Dual Dock and DX4 Quad
Dock. The DX2 and DX4 are
available in charge-only and
Ethernet configurations.

Ethernet Snap-On Adapter Use the Ethernet adapter to be able to

Handstrap Replacement Kit You can order and install a replacement

Holster Use the holster to store the computer

IP30 Handheld RFID Reader Use the IP30 Handheld RFID Reader to

Use the desktop dock with the:

• Computer cup to charge the battery

while it is installed in the computer.

• Battery cup to charge the battery.

Use these charger bases with the:

• Computer cup to charge batteries

while they are installed in the
computer.

• Battery cup to charge two batteries.

connect the computer to an Ethernet
network.

handstrap for the CN70, CN70e, and
CK70/CK71. Each kit contains 5
handstraps.

when you need your hands free.

connect via Bluetooth or USB to
read/write RFID tags.

RS-232 Snap-On Adapter Use the RS-232 adapter to convert the

connector on the bottom of the computer
to a serial connector.

Scan Handle Use the scan handle to provide better

ergonomics to the computer for
high-volume scanning applications.

Tethered Stylus Replacement Kit You can order and install a replacement

stylus.

USB Snap-On Adapter Use this adapter to convert the bottom

connector of the computer to a USB
connector.

Vehicle Dock Use the vehicle dock to provide power and

hold your computer while you are using it
in a vehicle.

8 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

Accessory Description

Vehicle Holder Use the vehicle holder to hold your

computer while you are using it in a
vehicle.

Vehicle Power Adapter Use the vehicle power adapter to provide

power to the computer from your vehicle.

Vocollect

® Snap-On Adapter

Use this adapter to be able to use the
Vocollect voice solution in your
warehouse.

About Language Provisioning

If your 70 Series computer includes language provisioning, you are
prompted to select a language provision when the computer starts for
the first time. It may take up to 15 minutes to load your language.

These languages are available:

• Chinese Simplified (CHS)

• Chinese Traditional (CHT)

• Spanish (ESN)

• French (FRA)

• German (GER)

• Italian (ITA)

• Japanese (JPN)

• Korean (KOR)

• Russian (RUS)

• World Wide English (WWE)

Make sure you select the correct language before you tap Provision. If
you want to change the language provisioning, you need to send your
computer to an Intermec Global Repair Center.

70 Series Mobile Computer User Manual 9

DRAFT

Chapter 1 — About the Computer Features

About the Battery

The battery used in this device may present a fire or chemical burn
hazard if it is mistreated. Do not disassemble it, heat it above
100 °C (212 °F) or incinerate it. Dispose of used batteries
promptly. Keep away from children.

The computers use these rechargeable Lithium-ion battery pack as the
main power source:

• 3.7 V, 4000 mAH (14.8 Wh) battery for the CN70 and CN70e

• 3.7 V, 5200 mAH (19.2 Wh) battery for the CK70 and CK71

Charge the Battery

You need to fully charge the battery before using your computer for the
first time. Use one of the charging accessories listed in the next table to
charge the battery.

70 Series Charging Accessories

Charging Accessory Charging Time

Snap-on adapters Up to 6 hours

DX1, DX2, or DX4 dock Up to 6 hours

CN70, CN70e, CK70, and CK71 Vehicle Power Adapter Up to 6 hours

Change the Battery

If your battery power is low, you need to either charge the battery in the
computer, or replace it with a charged battery.

1 Save your files and close any open applications.

2 Press the Power button and choose Hibernate from the menu to

suspend the computer.

10 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

3 Detach the handstrap from the computer.

Detach the Handstrap From a CN70 or CN70e

Detach the Handstrap From a CK70 or CK71

4 Make sure the computer is in hibernate mode and the screen is off.

5 Remove the battery.

• On the CN70 or CN70e, push the battery release toward the

bottom of the computer until the battery releases and then lift
it away from the computer.

70 Series Mobile Computer User Manual 11

DRAFT

Chapter 1 — About the Computer Features

• On the CK70 or CK71, push the battery release toward the top

of the computer until the battery releases and then lift it away
from the computer.

6 Insert the top end of a fully charged battery into the computer, and

press down firmly on the bottom of the battery. Make sure that the
battery release is fully engaged.

12 70 Series Mobile Computer User Manual

DRAFT

About Battery Status

Battery status LED

Use the battery icon on the Title bar to see the power status of your
battery. If you want more detailed information on your battery such as
usage time or voltage, use the Intermec Dashboard. For more
information on the Dashboard, see “About the Intermec

Dashboard” on page 114.

Battery Icon Status Descriptions

Battery Icon Status

Chapter 1 — About the Computer Features

Battery is fully charged.

Battery has a high charge.

Battery has a medium charge. You should be able to work for
several more hours before changing batteries.

Battery is low. You need to charge or replace the battery soon.

Battery is critically low. You need to replace the battery now.

Battery is charging.

The battery is not installed.

You can also use the battery status LED to see the charging status of
your battery.

70 Series Mobile Computer User Manual 13

DRAFT

Chapter 1 — About the Computer Features

Battery Status LED Descriptions

LED State Description

Steady green The computer is connected to a charger and the

Blinking red The battery is very low. The computer will soon go

Steady red The computer is connected to a charger and the

Blinking red-amber The battery charging system has encountered an

Steady amber The battery is outside of the allowable charging

Off The computer is not on external power and the

battery is more than 95% charged.

into Suspend mode. Charge or replace the battery.

battery is charging.

error. The battery is not charging.

temperature range. Charging will resume when the
battery temperature is back in the acceptable range of
5 °C to 35 °C (41 °F to 95 °F).

battery is operating normally.

About Battery Life and Conservation

Batteries that are stored outside the computer for long periods of time
slowly discharge. Intermec recommends storing the battery in a
charger to maintain battery performance.

Battery Conservation Tips

When You Want To: Do This to Save Battery Power:

Use the computer and the
Low Battery status icon
appears or the Battery
light comes on.

Stop using the computer
for 5 minutes or longer.

• Connect the computer to an external power

source.

• Or, save your data and press the Power button

and select Hibernate. After the computer
turns off, remove the battery and insert a fully
charged battery.

Make sure that the low battery icon is not on the
screen and the Battery LED is not on. Press the
Power button and choose Suspend to suspend
the computer.

14 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

Space

F

D

S

A

G H

J

K

L

C

X

Z

V

B

N

M

Esc

Enter

R

E

Q

W

T Y

I

O

P

U

%

&

?

@

$

sym

1

2

3

4

5

6

7

8

0

9

+

/

When You Want To: Do This to Save Battery Power:

Store the computer for
more than a day.

Store the battery outside
the computer.

About the Keypad

The CN70 comes with either a QWERTY keypad or a numeric keypad.
The CN70e comes with either a QWERTY numeric keypad, a
phone-style numeric keypad (1-2-3 digits across the top), or a
calculator-style numeric keypad (7-8-9 digits across the top). The
computer has an ambient light sensor that detects low light and turns
on the keypad backlight. By default, the keypad backlight is enabled in
low light conditions. You can disable the keypad backlight to conserve
power. Use Intermec Settings to configure the backlight. For help, see

“Use Intermec Settings on the Computer” on page 72.

If you are storing the computer for a few days,
like over the weekend, install a charged battery or
connect the computer to a power source.

If you are storing the computer for longer,
remove and charge the battery, and then store
both the battery and computer in a cool location.
If you store the battery for several months,
recharge the battery to keep it at peak
performance.

Store the batteries in a charger.

CN70 QWERTY Keypad

70 Series Mobile Computer User Manual 15

DRAFT

Chapter 1 — About the Computer Features

1

2

3

4

5

6

7

8

0

9

Caps

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

Space

WXYZ

Esc

Enter

CN70 Numeric Keypad

CN70e QWERTY Numeric Keypad

16 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

CN70e Calculator-Style Numeric Keypad

CN70e Numeric Keypad

70 Series Mobile Computer User Manual 17

DRAFT

Chapter 1 — About the Computer Features

%

The CK70 comes with either a large alpha or an alphanumeric keypad.
The CK71 comes with either a numeric function keypad or an
alphanumeric keypad. The computer has an ambient light sensor that
detects low light and turns on the keypad backlight. By default, the
keypad backlight is enabled in low light conditions. You can disable
the keypad backlight to conserve power. Use Intermec Settings to
configure the backlight. For help, see “Use Intermec Settings on the

Computer” on page 72.

CK70 Large Alpha Keypad

Esc

Send End

AB C

F1 F2 F3

123

D

F4

456

GI

F7 F9

789

KM

OQ

@

EF

F5 F6

H

F8

L

F10

0

PR

Enter

sym

Space

N

( )

[ ]

\

J

STUV

DeleteInsert

Z

W

+

X

=

Y

Ctrl

><

18 70 Series Mobile Computer User Manual

DRAFT

CK70 Alphanumeric Keypad

Chapter 1 — About the Computer Features

F6

F7

F8

F9

F10

F17

F23

Alt

F1

F2

F3

F4

F5

A

G

M

S

Ctrl

F13 F14F11 F12 F15 F16

CD

B

F18

F19 F20

H

IJ

F24

N

O

T

UV

564

897

0

Space

P

Y

F21

Q

W

DeleteInsert

E

K

Z

Esc

EndSend

312

Enter

F

F22

L

R

X

70 Series Mobile Computer User Manual 19

DRAFT

Chapter 1 — About the Computer Features

CK71 Numeric Function Keypad

Fld
Exit

A

View

Insert

Fld+Fld-

View

Roll

B C

SysRq

g

e

a

P

NxtScrPrvScr

Return

Enter

897

Delete

DEF

Roll

564

GHI

Home

Attn

JK

0

F13 F14 F15 F16

L

F1 F2 F3 F4

PQRS

F5 F6 F7 F8

TUYVW

MN O

F17 F18 F19 F20

F21 F22

Clear

PA3PA2PA1

312

Reset

Esc

Space

Return

Enter

F24F23

F9

F10 F1 1

X

Ctrl

F1 2

Z

Alt

20 70 Series Mobile Computer User Manual

DRAFT

CK71 Alphanumeric Keypad

g

e

a

P

897

Roll Clear

564

0

Space

Ctrl

CD

Hex

IJ

O

F21

Print

P

E

Keypd

K

SysRq

Q

F6

F7

F8

F9

F10

F17

F23

Fld
Exit

PrvScr Roll

PA1

F1

PA2

Insert

F2

PA3

Fld+Fld-

F3

Autolog

F4

EEOF

F5

F13 F14F11 F12 F15 F16

A

B

FldMk

Home

F18

F19 F20

G

H

Menu

NewLn

F24

M

N

View

Mode

NxtScr

Delete

Hel

Erase FindDupAttn

Alt

p

312

Enter

F22

Remove

Chapter 1 — About the Computer Features

Reset

Esc

Return

F

L

R

S

T

UV

?

Y

W

Select

Z

X

70 Series Mobile Computer User Manual 21

DRAFT

Chapter 1 — About the Computer Features

Enter Characters on the QWERTY Keypad

You need to use the orange modifier key b and the Shift key y to
access all characters and functions on the QWERTY keypad.

To type a character:

• Press the key for that character.

To type a character or access a function on the overlay:

• Press

To only type characters or access functions on the overlay:

• Press

press the keys for the characters or functions.

To type a single uppercase letter:

• Press

To type all uppercase letters:

• Press y y to turn on Caps Lock, and then press the letter keys.

You can still type orange modifier characters by pressing
the key for that character.

To turn off Caps Lock, press

b and then press the key for the character or function.

b twice to lock the orange modifier key to stay on, and then

y and then the letter key.

y.

Enter Characters on the Numeric Keypad

You need to use the orange modifier key b and the green modifier key

c to access all characters and functions on the Numeric keypad.

To type a character or access a function printed in orange on the
overlay:

b and then

• Press

To type a character or access a function printed in green on the overlay:

• Press

To type letters in the upper right corner of a key:

• Press

position of the letter.

22 70 Series Mobile Computer User Manual

b and then press the key for the character or function.

c and then press the key for the character or function.

c and then press the key one to three times depending on the

DRAFT

Chapter 1 — About the Computer Features

For example, in the upper right corner of the 2 key there are the
letters “ABC”:

• To type “c”, press

• To type “C,” press

Note: On the calculator-style keypad, the 2 is replaced by the 8.

To only type letters:

• Press

one to four times depending on the position of the letter.

While the green modifier key is locked, press
uppercase and lowercase letters.

To unlock the green modifier key, press

Note: If uppercase letters are enabled and you unlock the green
modifier key, you may need to press

c c to lock the green modifier key, and then press the key

c 2 2 2.

c 1 and then press c 2 2 2.

1 to toggle between only

c.

c 1 to type lowercase letters.

Enter Characters on the CK70 and CK71 Keypads

You need to use the orange modifier key b, the green modifier key c,
and the Shift or Caps Lock key
on the Alpha, Alphanumeric, and Numeric Function keypads.

y to access all characters and functions

To type a character or access a function printed in orange on the
overlay or in the upper left corner of a key:

• Press

To type a character or access a function printed in green on the overlay:

• Press

To type a single uppercase letter:

• Press

To type all uppercase letters:

• Press y y to turn on Caps Lock, and then press the letter keys.

You can still type orange or green modifier characters by pressing

c and then the key for that character.

To turn off Caps Lock, press

70 Series Mobile Computer User Manual 23

b and then press the key for the character or function.

c and then press the key for the character or function.

y and then the letter key.

b or

y.

DRAFT

Chapter 1 — About the Computer Features

About the Power Button

When you press the Power button, a dialog box with a list of power
options appears. If you do not select a power options setting, the
currently selected action (the button outlined in bold) occurs after the
timeout.

The Intermec Power Options Default Screen

Note: The Real Time Clock (RTC) persists through all of the power
options as long as it receives power from the Real Time Clock battery.

Intermec Power Options

Option Description

Hibernate
(battery swap)

24 70 Series Mobile Computer User Manual

High power saving mode. Use this setting only for
swapping the battery. The computer saves the current
system state, registry, and file system and then powers off
all radios and internal devices. You can wake the computer
by pressing the Power button or connecting the computer
to external power.

DRAFT

Chapter 1 — About the Computer Features

Option Description

Suspend Medium power saving mode. The computer powers off all

radios and internal devices not involved in saving the
system state, but the phone stays on to receive calls. This
option is the default setting. You can wake the computer
by pressing the Power button, pulling the scanner trigger,
receiving a call, scheduling an event such as an alarm, or
by connecting external power.

Reboot The computer does not save the current system state, but

the registry and file systems are saved. The computer
shuts down all running processes and restarts.

Cancel The Power Options menu is cancelled.

Screen Off Lowest power saving mode. The screen turns off, but the

phone, all radios, and internal devices stay on. Tap the
screen to turn the screen back on.

Shutdown Very high power saving mode. The computer turns off

everything. You must press Power or apply external power
to restart the computer.

The Intermec Power Options screen is customizable. You can use
Intermec Settings to determine which options are available to end
users, the timeout until the default choice is selected, the default
action if no option is selected, or to disable the Power Options screen.
For more information on customizing the screen using Intermec
Settings, see “Use Intermec Settings on the Computer” on page 72
or see the Intermec Settings Command Reference Manual.

About the Intermec Dashboard Button

If the Ready-to-Work light blinks, your computer may be experiencing
a problem. Press the Intermec Dashboard button (
Intermec Dashboard application and view troubleshooting and status
information.

You can press the
Dashboard. If the computer is not healthy, the current issues are
displayed at the top of the screen. If the device is healthy, you can use
the Dashboard to view device information. For more information, see

“About the Intermec Dashboard” on page 114.

m button at any time to bring up the Intermec

m) to launch the

70 Series Mobile Computer User Manual 25

DRAFT

Chapter 1 — About the Computer Features

Configure the Screen Backlight

The display has an ambient light sensor that automatically adjusts the
backlight intensity to conserve power and ensure the display is
readable.

By default, the screen turns off when there is no activity with the
computer. Press a key or tap the screen to resume activity.

You can configure the screen backlight to turn off.

1 Tap Start > Settings > Power.

2 Tap Advanced on the horizontal scroll bar.

3 Select the screen power off settings for when the computer is on

battery power or external power.

Configure the Screen Brightness

You can configure the screen brightness using Intermec Settings or
from the Start menu.

1 Tap Start > Settings > System > Backlight.

2 Adjust the slider to the desired brightness level.

3 Tap OK.

Adjust the Volume

You can adjust the computer volume for your needs and your
environment. The volume includes sounds you hear when you tap the
screen or read bar codes with the imager. You can set the volume to off,
very low, low, medium, high, very high (default), or vibrate.

You can also use the buttons on the right side of the computer to
adjust the volume:

• The upper button increases the volume.

• The lower button decreases the volume.

26 70 Series Mobile Computer User Manual

DRAFT

You can adjust the volume settings using Intermec Settings or the
horizontal scroll menu.

1 Tap the Volume icon at the top of the screen, and then tap the

volume icon on the horizontal scroll menu.

2 Use your stylus or the u and d keys to adjust the volume slider to

the volume you want, select Vibrate, or select Off.

About the Imager

The computer ships with an internal imager. You can use the imager as
a flashlight or to read bar codes.

Note: When the Pictures & Videos application is running, you cannot
use the imager.

Chapter 1 — About the Computer Features

Use the Imager as a Flashlight

You can use the EA30 imager as a flashlight. By default, the imager is
set to read bar codes. To use the imager as a flashlight, you must remap
the Left side lower button.

1 Open Intermec Settings on the mobile computer by tapping

Start > Settings > System > Intermec Settings.

2 From the Intermec Settings main menu, tap Device Settings >

Keypad.

3 From the Keypad menu, tap Button Remapping.

4 From the Left side lower button menu, select Flashlight.

5 From the Flashlight timeout drop-down menu, select how long to

leave the flashlight on before it automatically turns off.

6 Tap OK.

70 Series Mobile Computer User Manual 27

DRAFT

Chapter 1 — About the Computer Features

Read Bar Codes

Depending on the imager model in your computer, you can read 1D
and 2D bar code symbologies, composite symbologies, and postal
codes.

You can also connect the computer to cordless scanners (like the SF51
and SR61) through Bluetooth communications or tethered scanners
(like the SR30 and SR61T) through the RS-232 adapter. For help, see

“Connect to a Bluetooth Scanner” on page 84 and “Connect to a
Tethered Scanner” on page 88, respectively.

1 Enable only the bar code symbologies that you need.

2 Use Intermec Settings to select the predefined imager mode that

best suits your environment:

Predefined Mode For Scanning

1D Only 1D labels.

1D and 2D Standard (Default) All types of bar code labels.

1D and 2D Bright Environment In high ambient light, such as outdoors

in the sunshine.

1D and 2D Reflective Surface Glossy labels.

Note: You can also select the imager predefined mode in Profile
Settings by tapping Start > Profile Settings > Scanning.

3 Point the imager window at the bar code label, and hold the

computer steady a few inches from the label.

4 Press the Scan button. The laser pointer and illumination beam or

frame appear.

28 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

Scanning With the EA30 Imager

5 Use the laser pointer as a guide and aim toward the middle of the

bar code. Make sure that the illumination beam or frame covers the
bar code you are trying to decode.

When the computer successfully reads a bar code label, you hear a
high beep, and the Good Read LED turns on briefly.

6 Release the Scan button.

Read an RFID Tag

You can use the 70 Series RFID Demo to read a single or a group of
RFID tags. Follow the instructions below to read a single RFID tag:

1 Start the Intermec 70 Series RFID Demo.

2 Tap Start > Menu.The Read Mode tab appears.

3 From Scan mode drop-down menu, select Read single tag.

4 Position the tab an inch from the scanner.

5 Scan the tag.

6 If the read is successful, a table appears at the bottom of the screen

that displays the EPC value of the tag.

70 Series Mobile Computer User Manual 29

DRAFT

Chapter 1 — About the Computer Features

For more information about how to use the 70 Series RFID Demo
application, refer to the Intermec 70 Series RFID Demo User Guide.

Insert a MicroSD Card

You can use a microSD™ card to increase file storage and install
software. The computers support an optional 32 GB maximum
capacity microSD card.

Note: The computer resets when you open the card access door to
insert the microSD card. Make sure you completely close the card
access door before you use your computer.

Install a MicroSD Card in a CN70 or CN70e

You need a Phillips screwdriver to install the microSD card.

1 Press the Power button to turn off the computer.

2 Remove the handstrap and the battery.

30 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

3 Remove the two Phillips screws and open the card access door.

4 Slide the SIM card door to the left to unlock it and open the door.

5 Slide the microSD card door towards the top of the computer to

unlock it and open the door.

70 Series Mobile Computer User Manual 31

DRAFT

Chapter 1 — About the Computer Features

6 Slide the microSD card into place.

7 Close the microSD card door and slide it towards the bottom of the

computer to lock it in place.

8 Close the SIM card door and slide it to the right to lock it in place.

9 Close the card access door and replace the two screws.

10 Install the battery. Press down firmly on the bottom of the battery,

and make sure that the battery release tab is fully engaged.

11 Attach the handstrap.

12 Press the Power button. The computer cold boots.

32 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

Install a MicroSD Card in a CK70 or CK71

You need a Phillips screwdriver to install the microSD card.

1 Press the Power button to turn off the computer.

2 Remove the handstrap.

3 Remove the two screws that attach the interface adapter cover to

the back of the computer.

4 Slide the SIM card door to the left to unlock it and open the door.

5 Slide the microSD card door towards the top of the computer to

unlock it and open the door.

70 Series Mobile Computer User Manual 33

DRAFT

Chapter 1 — About the Computer Features

6 Slide the microSD card into place.

7 Close the microSD card door and slide it towards the bottom of the

computer to lock it in place.

8 Close the SIM card door and slide it to the right to lock it in place.

9 Replace the interface adapter cover and attach with the two screws

removed in Step 2.

10 Install the battery. Press down firmly on the bottom of the battery,

and make sure that the battery release tab is fully engaged.

11 Reattach the handstrap.

12 Press the Power button. The computer cold boots.

34 70 Series Mobile Computer User Manual

DRAFT

Chapter 1 — About the Computer Features

Transfer Files to and from Your PC

The 70 Series computer supports these two methods for transferring
files to and from your PC:

• Using Microsoft ActiveSync or Windows Mobile Device Center.

• Using the 70 Series computer as a mass storage device.

Use Microsoft ActiveSync to Transfer Files

You can use Microsoft ActiveSync (Windows XP or earlier) or Windows
Mobile Device Center (Windows Vista or Windows 7) to establish a
connection between your computer and a PC. After you connect to
your PC, you can transfer files, synchronize files, remotely debug, and
perform other device management activities. ActiveSync and Windows
Mobile Device Center are free applications available from the
Microsoft website at www.windowsmobile.com/getstarted.

To establish a partnership between your computer and a PC, you need
to physically connect your computer to your PC using these
accessories:

• USB snap-on adapter (Model 1000AA07)

• USB cable

Using these accessories, you can transfer files to and from your PC
using ActiveSync.

1 Connect your mobile computer to your desktop PC using the

adapter and USB cable.

2 Download ActiveSync from the Microsoft website and install

ActiveSync on your PC.

3 Follow the onscreen instructions to establish a partnership. When

the partnership is established, the Microsoft ActiveSync screen
appears on your PC.

70 Series Mobile Computer User Manual 35

DRAFT

Chapter 1 — About the Computer Features

Use the Computer as a Mass Storage Device

You can connect the 70 Series computer as a mass storage device to
your desktop PC. When connected as a mass storage device, you can
easily copy files to and from the mobile computer.

1 Go to www.datalight.com and download the Reliance Nitro

Windows Driver (RNWD). You need to login before you can
download the driver.

2 Connect the mobile computer to your desktop PC using a USB

cable.

3 On the mobile computer, tap

Start > Settings > System > Intermec Settings.

4 From the Intermec Settings Main Menu, tap Device Settings >

USB.

5 From the USB function driver menu, select Mass storage - Flash

File Store and tap OK.

6 Copy files to and from your desktop PC to the mobile computer.1

36 70 Series Mobile Computer User Manual

DRAFT

A

Specifications and Default Settings

127

DRAFT

Appendix A — Specifications and Default Settings

Physical and Environmental Specifications

CN70 & CN70 RFID Physical Dimensions

Dimensions 16.9 x 8.0 x 3.4 cm (6.66 x 3.14 x 1.35 in)

Weight 450 g (15.9 oz) with battery

CN70e & CN70e RFID Physical Dimensions

Dimensions 19.5 x 8.0 x 3.4 cm (7.66 x 3.14 x 1.35 in)

Weight 491 g (17.3 oz) with battery

CK70 & CK70 RFID Physical Dimensions

Dimensions 23.7 x 8.0 x 4.3 cm (9.33 x 3.16 x 1.69 in)

Weight 562 g (19 oz) with battery

CK71 Physical Dimensions

Dimensions 23.7 x 8.0 x 5.0 cm (9.33 x 3.16 x 1.98 in)

Weight 584 g (20.6 oz) with battery

Environmental Specifications

Operating temperature -20 °C to 60 °C (-4 °F to 140 °F)

Storage temperature -30 °C to 70 °C (-22 °F to 158 °F)

Charging temperature 5 °C to 35 °C (41 °F to 95 °F)

Relative humidity (operating) 5% to 95% non-condensing

Environmental rating IP67 compliant

Drop Specifications All corners and sides from 1.8 m (6 ft) per

MIL-STD 810F

128 70 Series Mobile Computer User Manual

DRAFT

Appendix A — Specifications and Default Settings

Power and Electrical Specifications

Battery type Rechargeable Lithium-ion (Li-ion) battery

Battery capacity

CN70/CN70e: 3.7 V, 4000 mAh (14.8 Wh)

CK70/CK71: 3.7 V, 5200 mAh (19.2 Wh)

Electrical rating x 4.37/4.8 V; 2/1,5 A

70 Series Non-Incendive Computer Specifications

The 70 Series mobile computers with non-incendive (NI) certification
comply with the following specifications for North America and
Canada regions only.

Location Suitable for use in Division 2 locations

Safety cULus Listing - ISA/ANSI 12.12.01

Gases Class I - Groups A, B, C, D

Dusts Class II - Groups F, G

Fibers and Flyings Class III

Maximum Ambient Temperature T6 rating with a maximum temperature

Operating System

Microsoft Windows Embedded Handheld.

of 50 °C

70 Series Mobile Computer User Manual 129

DRAFT

Appendix A — Specifications and Default Settings

Hardware

Main processor options TI OMAP3, 1 GHz

TI OMAP3, 600 MHz

Memory 512 MB RAM

Persistent storage 1 GB Flash

Removable storage up to 32 GB user-accessible microSD card slot

Keypad CN70: QWERTY, Numeric

CN70e: QWERTY Numeric, Numeric,
Calculator-style
CK70: Large Alpha, Alphanumeric
CK71: Numeric Function, Alphanumeric

Imaging options 5 megapixel color camera and EA30 area imager

(all), EV12 (CK71 only), or EX25 (CK71 only)

Back Accessory Interface Pin-outs

The back accessory interface provides power for peripheral devices out
the back of the CK70 and CK71 computers.

Pin Pin Name I/O Description

1 OTB_PWR Output Power supply for peripheral

2GND

3 OTB_RX Input DTE Data Receive

4 OTB_TX Output DTE Data Transmit

5 OTB_I/O_Voltage Input I/O Voltage Level

6 OTB_ID BiDir One Wire Bus for ID

7 OTB_RTS Output DTE Ready do Send

8 OTB_CTS Input DTE Clear to Send

Touch Screen Specifications

Transmissive VGA display with high-durability touch screen; 480 x
640 pixels; 8.9 cm (3.5 in) diagonal active area; LED backlight and
ambient light sensor.

130 70 Series Mobile Computer User Manual

DRAFT

Standard Communications

• UMTS (not available on CK71)

• CDMA (not available on CK71)

• Flexible Network Radio (not available on CK71)

• GPS (not available on CK71)

• 802.11a/b/g/n

• Bluetooth

• USB Full Speed V2.0 Host

• USB Full Speed V2.0 Client

Wireless LAN

Standards compliant IEEE 802.11a/b/g/n (2.4 GHz and 5 GHz), Single

Data rates up to 72Mbps

Appendix A — Specifications and Default Settings

Stream

Security 802.11i, WPA, WPA2, 802.1x (EAP-TLS, TTLS, PEAP,

Certifications WPA2™ (Enterprise, Personal), WPA™ (Enterprise,

Regulatory Approvals

FCC, CE, cULus Listed, DEMKO

EAP-FAST), WEP

Personal), Wi-Fi, WMM®, WMM Power Save, Cisco
Compatible Extensions (CCX 4.0)

70 Series Mobile Computer User Manual 131

DRAFT

Appendix A — Specifications and Default Settings

Bar Code Symbologies

The imagers support all of the bar code symbologies listed in the next table.

Supported Bar Code Symbologies

AustraliaPost* GS1 DataBar Omni-Directional

Aztec* Infomail*

BPO* Interleaved 2 of 5

Canada Post* Japan Post*

China Post* KoreanPost*

Codabar Matrix 2 of 5

Codablock A* Maxicode*

Codablock F* Micro PDF417*

Code 11 MSI

Code 39 PDF417*

Code 93 Planet*

Code 128/GS1-128 Plessey

DataMatrix* Postnet*

Dutch Post* QR Code*

EAN/UPC Standard 2 of 5

GS1 Composite SwedenPost*

GS1 DataBar Expanded Telepen

GS1 DataBar Limited TLC 39*

* These symbologies are not supported with the EV12 imager in the
CK71.

132 70 Series Mobile Computer User Manual

DRAFT

Imager Reading Distances

Typical reading distances are done in an office environment using
office lights (4 lux). Minimum distances are measured in the dark (0
lux). Both reading distances are provided in respective scan engine
integration guides. Contact your local Intermec representative for
more information.

Below are the typical and minimum standard reading distances for the
70 Series computer built with an EA30 imager. Also included are
typical and minimum standard reading distances for the CK71 with an
EV12 or EX25 imager.

Note: Minimum distances depend on the length of the bar code.

Appendix A — Specifications and Default Settings

70 Series Mobile Computer User Manual 133

DRAFT

Appendix A — Specifications and Default Settings

4"

8"

0"

4"

8"

12"

12"

cm

0.5 mm / 20 mils

1 mm / 40 mils

in

0" 36" 40"32"28"24"20"16"12"8"4"

0908070605040302010

100

EAN/UPC

0.125mm/5 mils

10

0

10

20

20

30

30

EA30 Typical Reading Distances - Extended Reading
Range

These typical reading distances are measured in an office environment
(250 lux) for the EA30 standard model with Extended Reading Range
activated. Extended Reading Range is enabled by default.

EA30 Typical Reading Distances - Extended Reading Range Activated

EA30 Typical Reading Distances - Extended Reading Range Activated

Symbology Density

Code 39 0.125 mm/5 mils

0.50 mm/20 mils
1 mm/40 mils

EAN/UPC 100% 0.33 mm/13 mils 6 cm/2.36 in 40 cm/15.75 in

134 70 Series Mobile Computer User Manual

Minimum
Distance

64.50 cm/2.56 in
7 cm/ 2.76 in

14.50 cm/5.71 in

Maximum
Distance

24.50 cm/9.65 in

62.50 cm/24.61 in

97.50 cm/38.39 in

DRAFT

Appendix A — Specifications and Default Settings

cm

PDF417 10 mils

0.5 mm / 20 mils

1 mm / 40 mils

Data Matrix 10 mils

in

0" 28"24"20"16"12"8"4"

070605040302010

EAN/UPC

0.125mm/5 mils

4"

8"

0"

4"

8"

12"

12"

10

0

10

20

20

30

30

EA30 Area Imager Minimum Reading Distances

Minimum distances are measured in the dark (0 lux).

EA30 Minimum Reading Distances

Symbology Density Minimum Distance Maximum Distance

Code 39 0.1 mm (4 mils)

0.1250 mm (5 mils)

UPC/EAN 100% 0.33 mm (13.0 mils) 6 cm (2.36 in) 31.5 cm (12.4 in)

Data Matrix 0.18 mm (7 mils)

PDF417 0.25 mm (10 mils)

70 Series Mobile Computer User Manual 135

0.5 mm (20 mils)
1 mm (40 mils)

0.25 mm (10 mils)

0.38 mm (15 mils)

038 mm (15 mils)

9.5 cm (3.74 in)
8 cm (3.15 in)
7 cm (2.76 in)

9.5 cm (3.74 in)

8 cm (3.15 in)

6.5 cm (2.56 in)

5.5 cm (2.17 in)

5.5 cm (2.17 in)
7 cm (2.76 in)

10.5 cm (4.13 in)
14 cm (5.51 in)
45 cm (17.72 in)
62 cm (24.41 in)

15.5 cm (6.1 in)

21.5 cm (8.46 in)

31.5 cm (12.4 in)

25 cm (9.84 in)
34 cm (13.39 in)

DRAFT

Appendix A — Specifications and Default Settings

EA30 Area Imager Typical Reading Distances

Typical distances are measured in an office environment (250 lux).

0" 36"32"28"24"20"16"12"8"4"

in

12"

8"

4"

0"

4"

8"

12"

PDF417 10 mils

0.125mm/5 mils

0908070605040302010

Data Matrix 10 mils

EAN/UPC

0.5 mm / 20 mils

1 mm / 40 mils

30

20

10

0

10

20

30

cm

EA30 Typical Reading Distances

Symbology Density Minimum Distance Maximum Distance

Code 39 0.1 mm (4 mils)

0.125 mm (5 mils)

0.5 mm (20 mils)
1 mm (40 mils)

UPC/EAN 100% 0.33 mm (13.0 mils) 6 cm (2.36 in) 34 cm (13.39 in)

Data Matrix 0.18 mm (7 mils)

0.25 mm (10 mils)

0.38 mm (15 mils)

PDF417 0.25 mm (10 mils)

0.38 mm (15 mils)

136 70 Series Mobile Computer User Manual

9.5 cm (3.74 in)
8 cm (3.15 in)

6.5 cm (2.56 in)

9.5 cm (3.74 in)

7.5 cm (2.95 in)
6 cm (2.36 in)

5.5 cm (2.17 in)

5.5 cm (2.17 in)

6.5 cm (2.56 in)

11.5 cm (4.53 in)

14.5 cm (5.71 in)
50 cm (19.69 in)
75 cm (29.53 in)

16.5 cm (6.5 in)
23 cm (9.06 in)

34.5 cm (13.58 in)

26 cm (10.24 in)
37 cm (14.57 in)

DRAFT

Appendix A — Specifications and Default Settings

0"

2"

8"

in

cm

0

10

20

0" 16" 12" 8" 4"

0 40 30 20 10

0.125 mm / 5 mils

0.25 mm / 10 mils

0.5 mm / 20 mils

1 mm / 40 mils

EAN/UPC 100%

5

15

10

20

5

15

6"

4"

5 15 25 35

2" 6" 10" 14"

1"

3"

5"

7"

2"

8"

6"

4"

1"

3"

5"

7"

EV12 Linear Imager Minimum Reading Distances

The illustration below does not include the 0.12 cm (0.05 in) setback
for the CK71. Minimum reading distances are measured in the dark (0
lux).

Symbology Density Minimum Distance Maximum Distance

Code 39 0.15 mm (6 mils)

EAN/UPC 0.33 mm (13 mils) 6.1 cm (2.5 in) 22.9 cm (9.1 in)

EV12 Minimum Reading Distances With 0.12 cm (0.05 in) Setback

0.25 mm (10 mils)

0.5 mm (20 mils)
1 mm (40 mils)

9.6 cm (3.8 in)

7.1 cm (2.9 in)

6.1 cm (2.5 in)

8.1 cm (3.2 in)

17.9 cm (7.1 in)

20.9 cm (8.3 in)

26.9 cm (10.6 in)

33.9 cm (13.4 in)

70 Series Mobile Computer User Manual 137

DRAFT

Appendix A — Specifications and Default Settings

0"

4"

16"

in

cm

0

20

40

0" 32" 24" 16" 8"

0 80 60 40 20

0.125 mm / 5 mils

0.25 mm / 10 mils

0.5 mm / 20 mils

1 mm / 40 mils

EAN/UPC 100%

10

30

20

40

10

30

12"

8"

10 30 50 70

4" 12" 20" 28"

2"

6"

10"

14"

4"

16"

12"

8"

2"

6"

10"

14"

90

36"

EV12 LInear Imager Typical Reading Distances

The illustration below does not include the 0.12 cm (0.05 in) setback
for the CK71. Typical reading distances are measured in an office
environment (200 lux).

EV12 Typical Reading Distances With 0.12 cm (0.05 in) Setback

Symbology Density Minimum Distance Maximum Distance

Code 39 0.15 mm (6 mils)

0.25 mm (10 mils)

0.5 mm (20 mils)
1 mm (40 mils)

EAN/UPC 0.33 mm (13 mils) 5.1 cm (2.1 in) 27.9 cm (11.0 in)

** Minimum distance depends on bar code width and scan angle.

138 70 Series Mobile Computer User Manual

9.6 cm (3.8 in)

6.1 cm (2.5 in)

5.1 cm (2.1 in)

7.1 cm (2.9 in)**

19.9 cm (7.9 in)

24.9 cm (9.8 in)

34.9 cm (13.8 in)

50.9 cm (20.1 in)

DRAFT

Appendix A — Specifications and Default Settings

in

0

50

cm

0” 32” 64” 80”16”

100% EAN contrast UPC

0.5 mm/20 mils

1 mm/40 mils

100 150 200 250 300 350 400 450

48” 96”

112”

128”

144” 160”

176”

1.4 mm/55 mils

32”

16”

48”

64”

16”

0”

80”

32”

48”

64”

80”

80

40

0

40

80

120

160

160

120

200

200

0.25 mm/10 mils

EX25 Near-Far Range Imager Minimum Reading
Distance

Minimum reading distances are measured in the dark (0 lux). The
following graphic does not include the 0.24 cm (0.09 in) setback for
the CK71.

EX25 Minimum Reading Distances With 0.24 cm (0.09 in) Setback

Symbology Density Minimum Distance Maximum Distance

Code 39 0.08 mm (3 mils)

0.1 mm (2.8 mils)

0.25 mm (10 mils)

0.5 mm (20 mils)
1 mm (40 mils)

EAN 100% 0.33 mm (13 mils) 15 cm (5.91 in) 145 cm (57.09 in)

70 Series Mobile Computer User Manual 139

1.3 mm (51 mils)

15 cm (5.91 in)
15 cm (5.91 in)
15 cm (5.91 in)
16 cm (6.30 in)
25 cm (9.84 in)
40 cm (15.75 in)

35 cm (13.78 in)
45 cm (17.72 in)
115 cm (45.28 in)
210 cm (82.68 in)
310 cm (122.05 in)
310 cm (122.05 in)

DRAFT

Appendix A — Specifications and Default Settings

EX25 Near-Far Range Imager Typical Reading Distance

Typical reading distances are measured in an office environment (200
lux). The following graphics do not include the 0.24 cm (0.09 in)
setback for the CK71.

EX25 Near-Far Range Imager 1D Typical Reading Distances

120” 160” 200”

0” 40”

in

160”

80”

240” 280” 320” 360” 400” 440”

480”

400

128”

96”

64”

32”

0”

32”

64”

96”

128”

160”

100% EAN
contrast UPC

0.25 mm
10 mils

0.5 mm/20 mils

0 100

1 mm/40 mils

2.5 mm/100 mils

200 300 600400 700500 1100

800 900 1000

320

240

160

80

0

80

160

240

320

400

cm

1200

140 70 Series Mobile Computer User Manual

DRAFT

Appendix A — Specifications and Default Settings

EX25 1D Symbologies Typical Reading Distances With 0.24 cm (0.09
in) Setback

Symbology Density Minimum Distance Maximum Distance

Code 39 0.25 mm (10 mils)

0.5 mm (20 mils)
1 mm (40 mils)

1.4 mm (55 mils)

2.5 mm (100 mils)

Code 128
retro-reflective

EAN 100% 0.33 mm (13 mils) 15 cm (5.91 in) 160 cm (62.99 in)

2.5 mm (100 mils) ** 1300 cm (511.81 in)

15 cm (5.91 in)
16 cm (6.30 in)
25 cm (9.84 in)
40 cm (15.75 in)
**

135 cm (53.15 in)
280 cm (110.24 in)
550 cm (216.54 in)
720 cm (283.46 in)
1200 cm (472.44 in)

** Minimum distance depends on bar code width and scan angle.

EX25 Near-Far Range Imager 2D Typical Reading Distances

160”

128”

96”

64”

0” 40”

in

120” 160” 200”

80”

240” 280” 320” 360” 400” 440”

480”

400

320

240

160

32”

0”

32”

64”

96”

128”

160”

70 Series Mobile Computer User Manual 141

0.76 mm/30 mils

0 100

0.25 mm
10 mils

1.4 mm/55 mils

2.5 mm/100 mils

200 300 600400 700500 1100

800 900 1000

80

0

80

160

240

320

400

cm

1200

DRAFT

Appendix A — Specifications and Default Settings

EX25 2D Symbologies Typical Reading Distances With 0.24 cm (0.09
in) Setback

Symbology Density Minimum Distance Maximum Distance

DataMatrix 0.25 mm (10 mils)

0.76 mm (30 mils)

1.4 mm (55 mils)

2.5 mm (100 mils)

7.5 mm (300 mils)

** Minimum distance depends on bar code width and scan angle.

Default Configuration

The following tables list the default values of the configuration
settings supported on the mobile computer. If you restore the mobile
computer to factory default settings, the mobile computer uses these
values.

The settings are grouped by function and reflect the organization of
Intermec Settings. Not all of the configuration settings are listed in
this appendix. For detailed information on most of the settings, see the

Intermec Settings Command Reference Manual.

15 cm (5.91 in)
25 cm (9.84 in)
**
**
20 cm (7.87 in)

90 cm (35.43 in)
310 cm (122.05 in)
450 cm (177.17 in)
1100 cm (433.07 in)
1524 cm (600 in)

Data Collection Settings

Use data collection settings to configure the imager and to configure
the bar codes that you want the imager to be able to read.

Data Collection Settings

Data Collection Setting Default Value

Enable Scanner/Camera Port On

BT-Configure On Connect Overwrite with computer settings

Enable Magstripe Reader Disable

142 70 Series Mobile Computer User Manual

DRAFT

Appendix A — Specifications and Default Settings

Symbology Settings

Symbology Default Value

AustraliaPost Disable

Aztec Disable

BPO Disable

CanadaPost Disable

Codabar Disable

Codablock A Disable

Codablock F Disable

Code 11 Disable

Code 39 Enable

Code 93 Disable

Code 128/GS1-128 Enable

DataMatrix Enable

DutchPost Disable

EAN/UPC Enable UPC A, UPC E, EAN 8, EAN 13

GS1 Composite Disable

GS1 DataBar Expanded Disable

GS1 DataBar Limited Disable

GS1 DataBar Omni-Directional Disable

Infomail Disable

Intelligent Mail Disable

Interleaved 2 of 5 Disable

JapanPost Disable

Matrix 2 of 5 Disable

Maxicode Disable

Micro PDF417 Disable

MSI Disable

PDF417 Enable

Planet Disable

Plessey Disable

Postnet Disable

QR Code Disable

Standard 2 of 5 Disable

70 Series Mobile Computer User Manual 143

DRAFT

Appendix A — Specifications and Default Settings

Symbology Default Value

SwedenPost Disable

Telepen Disable

TLC 39 Disable

Symbology Option Settings

Symbology Option Settings Default Value

Preamble None (Disabled)

Postamble None (Disabled)

Symbology Identifier Disable

Multicode Disable

Scanner Settings

Scanner Settings Default Value

Trigger Predefined Modes Level

Trigger Mode Level

Aimer Mode Typical aimer

Hardware Trigger Enable

Trigger Timeout (sec) 2

Aiming Duration (msec) 500

Turn Off After Good Read Enable/One-shot

Auto-Trigger delay (msec) 0

Imager Settings

Imager Settings Default Value

Predefined Modes 1D and 2D Standard

Image File Location \My Documents\MDI

Signature Image Capture Disable

Document Imaging Disable

144 70 Series Mobile Computer User Manual

DRAFT

Appendix A — Specifications and Default Settings

Imager Settings Default Value

Image Capture
Output Compression
Output Compression Quality
Edge Enhancement
Noise Reduction
Subsampling
Image Rotation
Image Lighting Correction

Decode Security Settings

Decode Security Settings Default Value

Consecutive Data Validation 0

Identical Consecutive Timeout 300 ms

Different Consecutive Timeout 0

Center Decoding Disable

Bitmap
0
None
0
None
None
Disable

Center Decoding Tolerance 0

Communications

Use communications settings to configure how the mobile computer
communicates with the network.

Communications Settings

Communications Setting Default Value

Device Name IntermecCXXX (where XXX indicates

802.11 Radio Settings

802.11 Radio Setting Default Value

Security Choice Funk

Allow Security Changes Enabled

Active Profile Profile 1

the model of mobile computer)

DHCP Enabled

Import Root Certificates False

Import User Certificates False

70 Series Mobile Computer User Manual 145

DRAFT

Appendix A — Specifications and Default Settings

802.11 Radio Setting Default Value

Import Pac Files False

Radio Bands b/g (2.4 GHz)

Radio Enabled Off

Ethernet Adapter Settings

Ethernet Adapter Setting Default Value

DHCP Enabled

Bluetooth Settings

Bluetooth Setting Default Value

Bluetooth Power Off

WWAN Radio Settings

WWAN Radio Setting Default Value

WWAN Radio Enabled Enabled

Serial Port Switch

Serial Port Switch Setting Default Value

Serial Port Switch Standard Docking and IrDA

RFID

RFID Setting Default Value

Enable RFID Service Enabled

Application Connection

Reader 1

• Allow External BRI Connection: enabled.

• BRI TCP Port: 2189

• Enable Logging: Off

• Enable Reader: On

• Connected: On

Reader Model: IM11

•

146 70 Series Mobile Computer User Manual

• RFID Module:

– Version: 1.00.0474

DRAFT

Appendix A — Specifications and Default Settings

RFID Setting Default Value

– Frequency: 915MHz or 865MHz

(Europe)

– Tag Type: EPC Class 1 Gen2

– Dense Reader Mode: On

– Field Separator: Space ()

–ID Report: On

–No Tag Report: Off

– Report Timeout: 0

–Timeout Mode: Off

– ID Timeout: 5000

– Antenna Timeout: 5000

–ID Tries: 1

– Antenna Tries:1

–Read Tries: 3

–Write Tries: 5

– Initialization Tries:1

– Lock Tries: 3

– Select Tries: 1

– Unselect Tries: 1

–Initial Q: 4

– Field Strength dB: 30

–Session: 2

– Enable Antenna Port 1: On

– Enable Antenna Port 2: Off

– Enable Antenna Port 3: Off

– Enable Antenna Port 4: Off

70 Series Mobile Computer User Manual 147

DRAFT

Appendix A — Specifications and Default Settings

Device Settings

Use device settings to configure settings on the mobile computer.

Device Settings

Device Setting Default Value

Date N/A

Time N/A

Good Read Settings

Good Read Setting Default Value

Internal Scanner Good Read Beep One Beep

Tethered Scanner One Beep

Bluetooth Scanner Good Read Beep One Beep

Backlight Settings

Backlight Setting Default Value

Display Backlight Adjustment Normal

Keypad Backlight On Based on Light Level

Light Level Low

Screen Settings

Screen Setting Default Value

Screen Rotations Portrait 0 Degrees

Screen Rotation Sensor Disabled

Sound Settings

Sound Setting Default Value

Beeper and Voice Medium

Headset Beeper Very Low

Vibrate Mode Intensity 1 Strong Pulse

Screen Taps Off

148 70 Series Mobile Computer User Manual

DRAFT

Appendix A — Specifications and Default Settings

Sound Setting Default Value

Key Clicks Off

Keypad Settings

Keypad Setting Default Value

Button Remapping Scanner

Power Management Settings

Power Management Setting Default Value

Enable Power Button Screen On

Screen Options Displayed Hibernate, Suspend,

Reboot

Screen Timeout (Seconds) 5

Power Button Behavior Suspend

Device Turns Off After (Battery Power) 5 minutes

Screen Turns Off After (Battery Power) Disabled

Device Turns Off After (External Power) Disabled

Screen Turns Off After (External Power) Disabled

Device Off Sensor Disabled

Profiles Settings Application

Profiles Settings Default Value

Camera

Disable Camera Scan
Enable Camera Scan

Power

Always On
Maximize Battery Life
Normal

Scanning

1D Bar Codes Optimized
Bright Sunlight
Reflective Labels
Standard

Show Option in Profile Settings
Show Option in Profile Settings

Show Option in Profile Settings
Show Option in Profile Settings
Show Option in Profile Settings

Show Option in Profile Settings
Show Option in Profile Settings
Show Option in Profile Settings
Show Option in Profile Settings

70 Series Mobile Computer User Manual 149

DRAFT

Appendix A — Specifications and Default Settings

GPS Settings

Use GPS settings to configure how the mobile computer
communicates with the GPS network.

GPS

GPS Setting Default Value

Enable Bread Crumbing Disable

Core Messaging Service Settings

Use core messaging service settings to configure the message routers
between client and server software applications.

Core Messaging Service

Core Messaging Service Setting Default Value

Associated Server IP Null

Broadcast Name INTERMEC

Port 62241

Keep Alive Ping Interval 30 Seconds

Device Monitor Settings

Use device monitor settings to configure how the mobile computer
monitors the network.

Device Health Controls

Device Health Setting Default Value

Enable Health Data Collection On

Enable Device Health Application On

Enable Blue Light Off for Ready-to-Work

Set Rule File Location \SmartSystems\HealthRules.txt

System Device Health Refresh (seconds) 90

Network Device Health Refresh (seconds) 45

150 70 Series Mobile Computer User Manual

DRAFT

Device Health Screen Captures

Device Health Screen Captures Setting Default Value

Directory \SmartSystems\ScreenCapture

Screen Captures Allowed 3

Device Wipe

Device Wipe Setting Default Value

Enable Wipe Disabled

Interval (in days) Null

Virtual Wedge Settings

Use virtual wedge settings to configure the virtual wedge.

Virtual Wedge Setting

Appendix A — Specifications and Default Settings

Setting Default Value

Virtual Wedge Enable

Bar Code Scanner Grid Null

Label Encoding (Code Page) 1252

Magstripe Reader Grid Null

70 Series Mobile Computer User Manual 151

DRAFT

Appendix A — Specifications and Default Settings

152 70 Series Mobile Computer User Manual