Intel LE-370-LE-370Z User Manual

1.5 Mb
Loading...

LE-370/LE-370Z

3.5 Inches Embedded Miniboard

User’s Manual

Edition: 1.0

2005/6/13

LE-370 User’s Manual

Copyright

Copyright 2004 - 2005. All rights reserved. This document is copyrighted and all rights are reserved. The information in this document is subject to change without prior notice to make improvements to the products.

This document contains proprietary information and protected by copyright. No part of this document may be reproduced, copied, or translated in any form or any means without prior written permission of the manufacturer.

All trademarks and/or registered trademarks contains in this document are property of their respective owners.

Disclaimer

The company shall not be liable for any incidental or consequential damages resulting from the performance or use of this product.

The company does not issue a warranty of any kind, express or implied, including without limitation implied warranties of merchantability or fitness for a particular purpose.

The company has the right to revise the manual or include changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or changes.

Trademark

All trademarks are the property of their respective holders.

Any questions please visit our website at http://www.commell.com.tw

2

LE-370 User’s Manual

Packing List:

Please check the package before you starting setup the system

Hardware:

LE-370/LE-370Z motherboard x 1

Cable Kit:

44-pin

44-pin

40-pin

44-pin ATA33 IDE Cable x 1

CPU Cooler (LE-370 only)

COM port & Printer Port Cable x 1

USB Cable x 1

PS/2 keyboard & mouse cable x 1

Floppy Cable x 1

Audio Cable x 1

1 to 3 power output cable

Other Accessories:

Divers CD (including User’s Manual) x 1

Printed User’s Manual x 1

Packing List

3

LE-370 User’s Manual

 

 

Index

 

Chapter

1 <Introduction> ..................................................................................

7

1.1

<Product Overview>..............................................................................

7

1.2

<Product Specification> ........................................................................

8

1.3

<Mechanical Drawing>........................................................................

10

1.4

<Block Diagram>.................................................................................

11

Chapter

2 <Hardware Setup>..........................................................................

13

2.1

<Connector Location>.........................................................................

13

2.2

<Jumper Location & Reference> ........................................................

14

2.3

<Connector Reference>......................................................................

15

 

2.3.1 <Internal Connector>...............................................................

15

 

2.3.2 <External Connector>..............................................................

15

2.4

<CPU & Memory Setup>.....................................................................

16

 

2.4.1 <CPU>.....................................................................................

16

 

2.4.2 <Memory> ...............................................................................

17

 

2.4.3 <CPU Cooler Installation>.......................................................

18

2.5

<CMOS Setup>...................................................................................

19

2.6

<Enhanced IDE & CF interface>.........................................................

20

2.7

<Floppy Port>......................................................................................

21

2.8

<Ethernet Interface> ...........................................................................

22

2.9

<Onboard Display Interface> ..............................................................

23

 

2.9.1 <Analog Display Interface> .....................................................

23

 

2.9.2 <Digital Display Interface>.......................................................

24

2.10 <Onboard Audio Interface>...............................................................

28

2.11 <GPIO Interface> ..............................................................................

29

2.12 <Power Supply & Fan> .....................................................................

30

 

2.12.1 <Power Input> .......................................................................

30

 

2.12.2 <Power Output> ....................................................................

30

 

2.12.3 <Fan connectors>..................................................................

30

4

LE-370 User’s Manual

 

2.13 <Switch & Indicator> .........................................................................

31

Chapter 3 <System Setup> .............................................................................

33

3.1 <Display Configuration>......................................................................

33

Chapter 4 <BIOS Setup> .................................................................................

35

Appendix A <I/O Port Pin Assignment>.........................................................

37

A.1

<IDE Port> ..........................................................................................

37

A.2

<Floppy Port> .....................................................................................

38

A.3

<IrDA Port> .........................................................................................

38

A.4

< VGA Port >.......................................................................................

38

A.5

<Serial Port>.......................................................................................

39

A.6

<LAN Port> .........................................................................................

39

A.7

<PS/2 Keyboard & Mouse Port> ........................................................

39

A.8

<LPT Port>…………………………………………………………………40

A.9<USB Port>…………………………………………………………………40

Appendix B <Flash BIOS> ..............................................................................

42

B.1

BIOS Auto Flash Tool ...................................................................

42

B.2

Flash Method ...............................................................................

42

Appendix C <Hardware Test> .........................................................................

44

C.1 <Power Consumption Test>...............................................................

44

Contact Information.........................................................................................

45

Packing List

5

LE-370 User’s Manual

(This Page is Left For Blank)

6

LE-370 User’s Manual

Introduction

Chapter 1 <Introduction>

1.1 <Product Overview>

LE-370/LE-370Z are the 3.5 inches embedded miniboards based on Intel 852GME/GM of platform, with Intel Pentium M/Celeron M processors supported, onboard VGA, LAN, Audio, USB2.0, CF, LVDS, and mini-PCI to meet the variable applications of users.

LE-370Z with onboard Intel Celeron M processor for ultra low power can offer the fanless solution for such as medical applications.

Intel 852GME/GM & ICH4 Chipset

The board integrates Intel 852GME/GM and ICH4 chipset, to provide built-in Intel Extreme Graphics Technology, and supports DDR200/266/333 memory up to 1G of capacity.

18/24-bit LVDS LCD interface

The board provides onboard 18/24-bit LVDS LCD interface, supports up to 1600 x 1200 of UXGA high resolution for LE-370, and up to 1400 x 1050 for LE-370Z.

Flexible Extension Interfaces

The board provides one Mini-PCI socket for wireless LAN module, video capture card and IEEE1394 add-on card. The board also provide optional PCI interface with a riser card to have up to 2 PCI devices.

Product Overview

7

 

LE-370 User’s Manual

 

 

Introduction

 

 

 

 

 

 

 

 

 

 

1.2 <Product Specification>

 

 

General Specification

 

 

 

 

 

 

 

LE-370

 

LE-370Z

 

 

 

Form Factor

3.5 inches Embedded Miniboard

 

 

 

CPU

Intel Pentium M/Celeron M

 

Embedded Intel Celeron M

 

 

 

 

 

 

Package: FC-PGA478

 

Ratio: 600MHz

 

 

 

 

 

 

FSB: 400/533MHz

 

FSB: 400MHz

 

 

 

Memory

1 x 184-pin DDR 266/333

 

1 x 184-pin DDR 200/266

 

 

 

 

 

 

SDRAM up to 1GB

 

SDRAM up to 1GB

 

 

 

 

 

 

ECC memory supported

 

Non-ECC supported

 

 

 

Chipset

Intel 852GME and ICH4

 

Intel 852GM and ICH4

 

 

 

BIOS

 

Phoenix-Award v6.00PG 4Mb PnP flash BIOS

 

 

 

Green Function

Power saving mode includes doze, standby and suspend modes.

 

 

 

 

 

 

ACPI version 1.0 and APM version 1.2 compliant

 

 

 

Watchdog Timer

System reset programmable watchdog timer with 1 ~ 255

 

 

 

 

 

 

sec./min. of timeout value

 

 

 

 

Real Time Clock

 

Intel ICH4 built-in RTC with lithium battery

 

 

 

Enhanced IDE

Enhanced UltraDMA100 IDE interface supports dual channels

 

 

 

 

 

 

and up to 2 ATAPI devices

 

 

 

 

 

 

 

One 44-pin IDE connector onboard

 

Multi-I/O Port

 

 

 

 

 

 

Chipset

 

Winbond W83627HF-AW controller

 

 

 

Serial Port

 

One external & one internal RS-232 serial ports

 

 

 

USB Port

 

Two Hi-Speed USB 2.0 ports with 480Mbps of transfer rate

 

 

 

Parallel Port

 

One bi-direction parallel port with SPP/ECP/EPP mode

 

 

 

Floppy Port

 

One slim type Floppy port

 

 

 

 

IrDA Port

 

One IrDA compliant Infrared interface supports SIR

 

 

 

K/B & Mouse

 

External PS/2 keyboard and mouse ports on rear I/O panel

 

 

 

GPIO

 

One 8-bit programmable GPIO interface

 

 

 

Hardware

Fan speed, CPU temperature and voltage monitoring

 

 

 

Monitor

 

 

 

 

 

VGA Display Interface

 

 

 

 

 

 

Chipset

 

Intel 852GME/GM built-in Intel Extreme graphics

 

 

 

Frame Buffer

 

Intel DVMT with up to 64MB of frame buffer size

 

 

 

Display Type

 

CRT, LCD monitor with analog display

 

 

 

Connector

 

External DB15 female connector on rear I/O panel

 

LCD Interface

 

 

 

 

 

 

Chipset

 

Intel 852GME/GM built-in LVDS interface

 

 

 

Interface

18/24-bit LVDS interface

 

 

 

 

 

 

 

12V backlight inverter connector

 

 

 

 

 

 

 

 

 

 

8

 

 

 

 

Product Specification

 

 

LE-370 User’s Manual

Introduction

 

Ethernet Interface

 

 

 

 

Controller

 

Intel 82562ET PHY

 

 

 

Type

10Base-T / 100Base-TX

 

 

 

 

 

 

 

auto-switching Fast Ethernet

 

 

 

 

 

 

 

Full duplex, IEEE802.3U compliant

 

 

 

Connector

 

External RJ45 connectors with LED on rear I/O panel

 

 

 

Audio Interface

 

 

 

 

Chipset

 

REALTEK ALC201A

 

 

 

Interface

 

2 channel 3D audio with Line-in, Line-out and MIC-in

 

 

 

Connector

External Audio phone jack for Line-out

 

 

 

 

 

 

 

Onboard audio connector with pin header

 

 

 

 

 

 

 

Onboard CD-IN connector

 

 

 

Expansive Interface

 

 

 

 

Mini-PCI

 

1 x 32-bit 5V/3.3V Mini-PCI socket

 

 

 

PCI

1 x optional PCI interface supports up to two PCI devices through

 

 

 

 

 

riser card

 

 

 

Solid State Disk

 

 

 

 

 

DOM

 

IDE1 supports 44-pin DOM (DiskOnModule)

 

 

 

CompactFlash

 

1 x CompactFlash Type 1 socket on solder side

 

 

 

Power and Environment

 

 

 

Power

 

DC 12V input

 

 

 

Requirement

 

1 x DC jack on I/O panel or 1 x 4-pin DC connector onboard

 

Dimension

 

154 (L) x 101 (H) mm

 

 

 

Temperature

Operating within 0 ~ 60oC (32 ~ 140oF)

 

 

 

 

 

 

 

Storage within -20 ~ 85oC (-4 ~ 185oF)

 

 

 

 

 

 

 

 

 

Software support

 

 

 

 

Operation

 

Windows 98SE/ME, Windows 2000, Windows XP

 

 

 

System

Linux (Fedora Core 1, Mandrake 9.2 and Red Hat 9.0)

 

 

 

 

 

Linux Kernel version 2.4 or later

 

 

 

 

 

 

 

 

Ordering Code

 

 

 

 

LE-370

Intel Pentium M/Celeron M with socket479, VGA, AC97 Audio,

 

 

 

 

 

LVDS, CF, PCI, Mini-PCI, 2 x RS232, LAN,

 

 

 

LE-370Z

Same with above but with onboard Intel Celeron M 600 processor

1. The specifications may be different as the actual production.

For further product information please visit the website at http://www.commell.com.tw

Product Specification

9

LE-370 User’s Manual

Introduction

1.3 <Mechanical Drawing>

10

Mechanical Drawing

LE-370 User’s Manual

Introduction

1.4 <Block Diagram>

Intel Pentium M processor with FC-PGA2/FC-BGA2

CRT/LCD Monitor

LVDS 1 x 184-pin DDR

DIMM up to 1GB

852GME/GM

2 x USB2.0 Ports

82562ET PHY

 

 

PCI

 

 

 

 

 

 

ICH4

AC97 Codec

 

 

 

 

 

 

 

 

Mini-PCI

 

2 x Serial ports

 

 

 

 

 

 

 

 

 

BIOS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 x Floppy ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8-bit GPIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IrDA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 x Parallel port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Block Diagram

11

LE-370 User’s Manual

(This Page is Left for Blank)

12

LE-370 User’s Manual

Hardware Setup

Chapter 2 <Hardware Setup>

2.1 <Connector Location>

CN_COM2 AUDIO COM1 CDIN CRT CN_INV RJ45 PS2 DC_IN

CN_USB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_12V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_DIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_SPWR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LPT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CPUFAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_LVDS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYSFAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MINIPCI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIMM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_IR IDE1

JFRNT

FDD

CF

Connector Location

13

LE-370 User’s Manual

Hardware Setup

 

 

 

 

 

 

2.2 <Jumper Location & Reference>

 

 

 

 

 

 

 

 

 

Jumper

 

Function

 

 

 

 

JRTC

 

CMOS Operating/Clear Setting

 

 

 

JVLCD

 

LCD panel voltage setting

 

JVLCD

JRTC

14

Jumper Location & Reference

LE-370 User’s Manual Hardware Setup

2.3 <Connector Reference>

2.3.1 <Internal Connector>

Connector

 

Function

 

Remark

DIMM

184-pin DDR SDRAM DIMM

 

Standard

IDE1

44-pin primary IDE connector

 

Standard

FDD

 

26-pin slim type floppy connector

 

Standard

CN_12V

 

4-pin DC input connector

 

Standard

CDIN

4-pin CD-ROM audio input connector

 

Standard

CN_DIO

6 x 2-pin digital I/O connector

 

Standard

CN_USB

5 x 2-pin USB connector

 

Standard

CPUFAN

3-pin CPU cooler fan connector

 

Standard

SYSFAN

3-pin system cooler fan connector

 

Standard

CN_COM2

5 x 2-pin RS232 serial port

 

Standard

CN_IR

5-pin IrDA connector

 

Standard

CF

 

Compact Flash Type I socket

 

Standard

MINI_PCI

Mini-PCI interface

 

Standard

CN_LVDS

 

40-pin LVDS LCD interface

 

Standard

CN_INV

5-pin LCD backlight inverter connector

 

Standard

LPT

 

26-pin parallel port interface

 

Standard

JFRNT

 

14-pin front panel switch/indicator connector

 

Standard

CN_SPWR

 

4-pin DC 5V/12V output connector

 

Standard

2.3.2 <External Connector>

Connector

 

Function

 

Remark

CRT

 

DB15 VGA connector

 

Standard

RJ45

 

RJ45 LAN connector

 

Standard

COM1

Serial port connector

 

Standard

PS2

PS/2 Keyboard/Mouse connector

 

Standard

Audio

 

Audio Line-out port

 

Standard

DC_IN

DC input jack

 

Standard

Connector Reference

15

LE-370 User’s Manual

Hardware Setup

2.4 <CPU & Memory Setup>

2.4.1 <CPU>

LE-370 supports onboard socket479 for Intel Pentium M/Celeron M processors with FC-PGA478 package, 400/533MHz of front side bus; LE-370Z integrates onboard Intel Celeron M 600MHz processor with 400MHz of front side bus. For LE-370 please follow the instruction to install the CPU properly.

1. Use flat-type Screw Driver to unlock the CPU locket

CPU locker

CPU Socket

2. Find the pin direction and install the processor on the socket.

Unlock way

3. Lock the socket well.

16

CPU & Memory Setup

LE-370 User’s Manual

Hardware Setup

2.4.2 <Memory>

LE-370 supports DDR266/333 up to 1GB with ECC; LE-370Z supports DDR200/266 up

to 1GB with unbuffered, non-ECC memory module.

DIMM

 

 

 

104-pin

 

80-pin

Please check the pin number to match the socket side well before installing memory module.

CPU & Memory Setup

17

LE-370 User’s Manual

Hardware Setup

2.4.3 <CPU Cooler Installation>

The LE-370 provides one CPU cooler; please follow the instruction below to finish the installation. The LE-370Z comes with a heat sink on embedded processor, no fan is required.

1. Install CPU properly

 

2. Put the cooler on the socket

 

3. Press the clips into the through hole

4. Connect with CPUFAN connector

18

CPU & Memory Setup

LE-370 User’s Manual

Hardware Setup

2.5 <CMOS Setup>

The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.

Jumper: JRTC

Type: Onboard 3-pin jumper

JRTC Mode

1-2

 

Clear CMOS

2-3

 

Normal Operation

Default setting

JRTC 3

1

CMOS Setup

19

LE-370 User’s Manual

Hardware Setup

2.6 <Enhanced IDE & CF interface>

The board supports one UltraDMA133 IDE interface, and one CompactFlash Type 1 socket with secondary IDE mode, the 44-pin IDE1 connector can support up to 2 ATAPI devices through IDE cable.

2

44

1

IDE1

43

CF

20

Enhanced IDE & CF Interface

LE-370 User’s Manual

Hardware Setup

2.7 <Floppy Port>

The board provides a slim type floppy port; please use the 26-pin ribbon cable in the

package to connect the floppy device.

FDD

1.Lift up the brown plastic bar

2.Slot the cable in (Blue paste for brown bar side)

3.Press back the plastic bar

Floppy rear side

4. Lift up this plastic bar

5. Slot the cable in (Blue paste for outside)

6. Press back the plastic bar

Floppy Port

21

LE-370 User’s Manual

Hardware Setup

2.8 <Ethernet Interface>

The board integrates Ethernet controller with Intel 82562ET PHY, full compliance with IEEE 802.3u 100Base-T specifications and IEEE 802.3x Full Duplex Flow Control, the board supports Wake-Up-On-LAN by BIOS configurable.

RJ45

For Wake Up On LAN function, please enable this option in the BIOS

22

Ethernet Interface

LE-370 User’s Manual

Hardware Setup

2.9 <Onboard Display Interface>

Based on Intel 852GME/GM chipset with built-in Intel Extreme Graphics, the board provides onboard VGA display interface, and one 18/24-bit LVDS LCD interface, supports up to 1600 x 1200 of resolution for LE-370 (with 852GME) and 1400 x 1050 for LE-370Z

(with 852GM). The two display interfaces can be set for dual display with extended desktop mode or clone mode.

Below are the main features lists:

z128-bit 2D/3D graphics engine

zUp to 64MB of dynamic video memory allocation.

zHardware Motion Compensation for MPEGII

zDual display supported for Clone mode and Extended Desktop mode

2.9.1 <Analog Display Interface>

The onboard VGA display comes with standard DB15 connector on real I/O panel.

CRT (Analog Display Interface)

Onboard Display Interface

23

LE-370 User’s Manual

Hardware Setup

2.9.2 <Digital Display Interface>

The onboard digital display interface comes with a 40-pin header connector to provide 18/24-bit LVDS LCD interface, and one backlight inverter connector for powering and enable/disable control, the jumper JVLCD is to set the panel voltage.

 

 

 

 

 

 

CN_INV

1

3

40

2

 

5

 

 

 

JVLCD

 

CN_LVDS

 

 

 

 

 

 

 

39

 

1

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

Onboard Display Interface

LE-370 User’s Manual

 

 

 

 

Hardware Setup

Connector: CN_INV

 

 

Connector: JVLCD

Type: 5-pin LVDS Power Header

Type: 3-pin Power select Header

 

Pin

Description

 

 

Pin

Description

 

 

1

+12V

 

 

1

 

VCC

 

 

2

GND

 

 

2

 

LCDVCC

 

 

3

GND

 

 

3

 

VCC3

 

 

 

 

4

GND

 

 

 

 

 

 

 

5

ENABKL

 

 

 

 

Connector: CN_LVDS

Type: onboard 40-pin connector for LVDS connector

Connector model: HIROSE DF13-40DP-1.25V

Pin

Signal

Pin

Signal

2

LCDVCC

1

LCDVCC

4

GND

3

GND

6

ATX0-

5

BTX0-

8

ATX0+

7

BTX0+

10

GND

9

GND

12

ATX1-

11

BTX1-

14

ATX1+

13

BTX1+

16

GND

15

GND

18

ATX2-

17

BTX2-

20

ATX2+

19

BTX2+

22

GND

21

GND

24

ATXCK-

23

BTX3-

26

ATXCK+

25

BTX3+

28

GND

27

GND

30

ATX3-

29

BTXCK-

32

ATX3+

31

BTXCK+

34

GND

33

GND

36

N/C

35

N/C

38

N/C

37

N/C

40

N/C

39

N/C

Onboard Display Interface

25

LE-370 User’s Manual

Hardware Setup

To setup the LCD, you need the component below:

1.A panel with LVDS interfaces.

2.An inverter for panel’s backlight power.

3.A LCD cable and an inverter cable.

For the cables, please follow the pin assignment of the connector to make a cable, because every panel has its own pin assignment, so we do not provide a standard cable; please find a local cable manufacture to make cables.

LCD Installation Guide:

1.Preparing the LE-370, LCD panel and the backlight inverter.

2.Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.

3.You would need a LVDS type cable.

Panel side

Board side

For sample illustrator only

4.To connect all of the devices well.

26

Onboard Display Interface

LE-370 User’s Manual

Hardware Setup

After setup the devices well, you need to select the LCD panel type in the BIOS.

The panel type mapping is list below:

BIOS panel type selection form

For 18-bit color

For 24-bit color

NO.

Output format

NO.

Output format

 

 

 

 

1

640 x 480

8

1024 x 768

 

 

 

 

2

800 x 600

9

1280 x 1024 Dual Channel

 

 

 

 

3

1024 x 768

10

1400 x 1050 Dual Channel

 

 

 

 

4

1280 x 1024

11

1600 x 1200 Dual Channel

 

 

 

 

5

1400 x 1050 Dual Channel @ 108Mhz

13

1024 x 768 Dual Channel

 

 

 

 

6

1400 x 1050 Dual Channel @ 122Mhz

 

 

 

 

 

 

7

1600 x 1200 Dual Channel

15

1280 x 768

 

 

 

 

12

1024 x 768 Dual Channel

 

 

 

 

 

 

Notice: Panel type 7, 11 and 14 are only supported by LE-370, not for LE-370Z

Onboard Display Interface

27

LE-370 User’s Manual

Hardware Setup

2.10 <Onboard Audio Interface>

The board integrates onboard AC97 audio with REALTEK ALC201A, supports 18-bit ADC and DAC resolution, and Line-out, Line-in and MIC-in input/output interfaces.

Connector: CN_AUDIO

Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header

 

Pin

Description

Pin

Description

 

1

Line – Left

2

Ground

 

3

Line – Right

4

MIC1

 

5

MIC2

6

Ground

 

7

N/C

8

Line Out – Left

 

9

Line Out – Right

10

Ground

Connector: CDIN

 

 

Type: 4-pin header (pitch = 2.54mm)

 

 

 

Pin

Description

 

 

1CD – Left

2Ground

3Ground

4CD – Right

CDIN

Audio (Line-out)

1 4

1 2

9 10 CN_AUDIO

28

Onboard Audio Interface

LE-370 User’s Manual

Hardware Setup

2.11 <GPIO Interface>

The board offers 8-bit digital I/O to customize its configuration to your control needs. For example, you may configure the digital I/O to control the opening and closing of the cash drawer or to sense the warning signal from a tripped UPS.

Connector: CN_DIO

Type: onboard 2 x 6-pin 1.27mm x 2.54mm-pitch header

 

Pin

Description

Pin

Description

1

Ground

2

Ground

3

LGP0

4

LGP4

5

LGP1

6

LGP5

7

LGP2

8

LGP6

9

LGP3

10

LGP7

11

VCC

12

+12V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 2

11 12 CN_DIO

GPIO Interface

29

LE-370 User’s Manual

Hardware Setup

2.12 <Power Supply & Fan>

2.12.1 <Power Input>

The board requires DC 12V input with onboard DC jack or 4-pin 12V DC connector.

Connector: CN_12V

Type: 4-pin standard ATX2.0 +12V power connector

Pin

Description

Pin

Description

1

Ground

2

Ground

3

+12V

4

+12V

2.12.2 <Power Output>

The board also provides one 4-pin connector with +5V/+12V output.

 

Connector: CN_SPWR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type: 4-pin P-type connector for +5V/+12V output

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Description

Pin

Description

Pin

Description

Pin

Description

 

 

1

 

+12V

2

Ground

3

 

Ground

4

 

+5V

 

PS: Maximum output current for 5V/1A & 12V/1A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.12.3 <Fan connectors>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connector: CPUFAN, SYSFAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type: 3-pin fan wafer connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Description

Pin

Description

 

 

 

Pin

 

Description

 

 

1

 

Ground

 

2

+12V

 

 

3

 

 

Fan Control

 

 

 

 

 

 

 

 

 

 

 

 

DC_IN

 

 

 

CN_12V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CN_SPWR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYSFAN/CPUFAN

30

Power Supply & Fan

LE-370 User’s Manual

Hardware Setup

2.13 <Switch & Indicator>

The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Please check well before you connecting the cables on the chassis.

Connector: JFRNT

Type: onboard 14-pin (2 x 7) 2.54-pitch header

Function

Signal

 

PIN

Signal

Function

 

 

 

 

 

 

 

IDE LED

VCC

1

 

2

VCC

Power

 

 

 

 

 

Active

3

 

4

N/C

 

 

LED

 

 

 

 

 

 

Reset

Reset

5

 

6

GND

 

 

 

 

 

 

 

 

GND

7

 

8

VCC

 

 

 

 

 

 

 

 

 

 

 

 

N/C

9

 

10

N/C

Speaker

 

 

 

 

 

 

Power

PWRBT

11

 

12

N/C

 

 

Button

 

 

 

 

 

 

5VSB

13

 

14

SPKIN

 

 

 

 

 

 

 

 

14

JFRNT

1

Switch & Indicator

31

LE-370 User’s Manual

(This Page is Left for Blank)

32

LE-370 User’s Manual

System Setup

Chapter 3 <System Setup>

3.1 <Display Configuration>

The board provides onboard VGA with DB15 analog display interface, and LVDS LCD interface for digital display, when connecting two display devices, you can enable dual display function with clone mode or extended desktop mode.

Before setup the video setting, please install the VGA driver well.

Two controllers for each display device

There are two options for secondary display device

For more display properties setting,

please click “Advanced” button.

Click here for more details of

display setup

Display Configuration

33

LE-370 User’s Manual

System Setup

 

 

 

Please select Devices for advanced device setting.

Single Display

Device Setting

Dual Display

Device Setting

When you set dual display clone mode, you’ll see the same screen display on two devices.

When you set the dual display for extended desktop mode, you can have the independent desktop on the second device.

34

Display Configuration

LE-370 User’s Manual

BIOS Setup

Chapter 4 <BIOS Setup>

The single board computer uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers. The BIOS provides critical low-level support for the system central processing, memory and I/O sub-systems.

The BIOS setup program of the single board computer let the customers modify the basic configuration setting. The settings are stored in a dedicated battery-backed memory, NVRAM, retains the information when the power is turned off. If the battery runs out of the power, then the settings of BIOS will come back to the default setting. The BIOS section of the manual is subject to change without notice and is provided here for reference purpose only. The settings and configurations of the BIOS are current at the time of print, and therefore they may not be exactly the same as that displayed on your screen.

To activate CMOS Setup program, press DEL key immediately after you turn on the system. The following message “Press DEL to enter SETUP” should appear in the lower left hand corner of your screen. When you enter the CMOS Setup Utility, the Main Menu will be displayed as Figure 3-1. You can use arrow keys to select your function, press Enter key to accept the selection and enter the sub-menu.

Figure 3-1. CMOS Setup Utility Main Screen

BIOS Setup

35

LE-370 User’s Manual

(This Page is Left for Blank)

36

LE-370 User’s Manual

I/O Port Pin Assignment

Appendix A <I/O Port Pin Assignment>

A.1 <IDE Port>

Connector: IDE1

 

 

2

44

 

 

 

 

 

Type: 44-pin (22 x 2) box header

 

1

43

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Description

Pin

 

Description

 

 

1

Reset

2

 

Ground

 

 

3

D7

4

 

D8

 

 

5

D6

6

 

D9

 

 

7

D5

8

 

D10

 

 

9

D4

10

 

D11

 

 

11

D3

12

 

D12

 

 

13

D2

14

 

D13

 

 

15

D1

16

 

D14

 

 

17

D0

18

 

D15

 

 

19

Ground

20

 

N/C

 

 

21

REQ

22

 

Ground

 

 

23

-IOW

24

 

Ground

 

 

25

-IOR

26

 

Ground

 

 

27

IORDY

28

 

Ground

 

 

29

DACK

30

 

Ground

 

 

31

IRQ14

32

 

N/C

 

 

33

A1

34

 

GPI1

 

 

35

A0

36

 

A2

 

 

37

-CS1

38

 

-CS3

 

 

39

-HD LED1

40

 

Ground

 

 

41

+5V

42

 

+5V

 

 

43

Ground

44

 

Ground

 

IDE Port

37

LE-370 User’s Manual

 

I/O Port Pin Assignment

 

 

 

 

 

 

 

 

A.2 <Floppy Port>

 

 

 

 

 

Connector: FDD

 

 

 

 

 

Type: 26-pin connector

 

 

 

 

 

 

Pin

Description

Pin

Description

 

 

 

1

VCC

2

INDEX

 

 

 

3

VCC

4

DRV0

 

 

 

5

VCC

6

DSKCHG

 

 

 

7

DRV1

8

N/C

 

 

 

9

MTR1

10

MTR0

 

 

 

11

RPM

12

DIR

 

 

 

13

N/C

14

STEP

 

 

 

15

Ground

16

WRITE DATA

 

 

 

17

Ground

18

WRITE GATE

 

 

 

19

N/C

20

TRACK 0

 

 

 

21

N/C

22

WRPTR

 

 

 

23

Ground

24

RDATA-

 

 

 

25

Ground

26

SEL

 

 

A.3 <IrDA Port>

 

5

1

 

 

Connector: CN_IR

 

 

 

Type: 5-pin header for SIR Ports

 

 

 

 

 

 

Pin

Description

 

 

 

 

 

1

VCC

 

 

 

 

 

2

N/C

 

 

 

 

 

3

IRRX

 

 

 

 

 

4

Ground

 

 

 

 

5

IRTX

 

 

 

 

A.4 < VGA Port >

 

 

1

6

11

 

 

 

 

 

 

 

2

 

12

 

 

 

 

3

 

13

 

 

 

 

4

 

14

Connector: CRT

 

 

5

 

15

 

 

 

10

Type: 15-pin D-sub female connector on bracket

 

 

 

 

 

Pin

Description

Pin

Description

Pin

Description

1

RED

6

Ground

11

N/C

 

2

GREEN

7

Ground

12

5VSDA

 

3

BLUE

8

Ground

13

HSYNC

4

N/C

9

N/C

14

VSYNC

5

Ground

10

Ground

15

5VSCL

 

38

Floppy Port

LE-370 User’s Manual I/O Port Pin Assignment

A.5 <Serial Port>

 

 

1

6

 

 

 

 

2

Connector: COM1

 

 

3

7

 

 

4

8

Type: 9-pin D-sub male connector on bracket

 

5

9

 

 

 

Pin

Description

Pin

Description

 

 

1

DCD

6

DSR

 

 

2

RXD

7

RTS

 

 

3

TXD

8

CTS

 

 

4

DTR

9

-XR

 

 

5

Ground

 

 

 

 

Connector: CN_COM2

 

 

1

2

 

 

9

10

Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header

 

 

Pin

Description

Pin

Description

 

 

1

DCD

2

 

 

 

3

RXD

4

RTS

 

 

5

TXD

6

CTS

 

 

7

DTR

8

-XR

 

 

9

Ground

10

 

 

 

A.6 <LAN Port>

 

 

 

 

 

 

 

 

1

Connector: RJ45

 

 

 

 

 

 

 

 

 

Type: RJ45 connector with LED on bracket

 

 

 

 

8

Pin

1

2

3

4

5

6

 

7

8

Description

TX+

TXRX+ RX-

N/C

N/C

N/C

N/C

A.7 <PS/2 Keyboard & Mouse Port>

 

 

1

3

 

Connector: PS2

 

 

 

 

 

 

5

 

 

 

 

 

 

 

 

Type: 6-pin Mini-DIN connector on bracket

 

 

2

4

6

 

 

 

 

 

 

 

 

Pin

1

 

2

3

4

 

5

 

6

Description

KBD

 

MSD

Ground

VCC

KBC

 

MSC

Note: The PS/2 connector supports standard PS/2 keyboard directly or both PS/2 keyboard and

mouse through the PS/2 Y-type cable.

Serial Port

39

LE-370 User’s Manual

 

I/O Port Pin Assignment

 

 

 

 

 

 

 

 

A.8 < LPT Port >

 

14

26

 

 

Connector: CN_LPT

 

1

13

 

 

Type: 26-pin (13 x 2) header for LPT Ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Description

Pin

Description

 

 

 

1

PSTB-

2

PRO0

 

 

 

3

PRO1

4

PRO2

 

 

 

5

PRO3

6

PRO4

 

 

 

7

PRO5

8

PRO6

 

 

 

9

PRO7

10

ACK-

 

 

 

11

BUSY

12

PE

 

 

 

13

SLCT

14

AFD-

 

 

 

15

ERR-

16

INT-

 

 

 

17

SLIN-

18

Ground

 

 

 

19

Ground

20

I/O Ground

 

 

 

21

Ground

22

Ground

 

 

 

23

Ground

24

Ground

 

 

 

25

Ground

26

N/C

 

 

A.9 < USB Interface >

 

 

 

 

 

Connector: CN_USB

 

9

1

 

 

 

 

 

 

 

Type: 10-pin (5 x 2) header for dual USB Ports

10

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

Description

Pin

Description

 

 

 

1

VCC

2

VCC

 

 

 

3

Data0-

4

Data1-

 

 

 

5

Data0+

6

Data1+

 

 

 

7

Ground

8

Ground

 

 

 

9

Ground

10

NC

 

 

40

Serial Port

LE-370 User’s Manual

I/O Port Pin Assignment

(This Page is Left for Blank)

Serial Port

41

LE-370 User’s Manual

Flash BIOS

 

 

 

Appendix B <Flash BIOS>

B.1 BIOS Auto Flash Tool

The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below:

http://www.award.com

http://www.commell.com.tw/support/support.htm

File name of the tool is “awdflash.exe”, it’s the utility that can write the data into the BIOS flash ship and update the BIOS.

B.2 Flash Method

1.Please make a bootable floppy disk.

2.Get the last .bin files you want to update and copy it into the disk.

3.Copy awardflash.exe to the disk.

4.Power on the system and flash the BIOS. (Example: C:/ awardflash XXX.bin)

5.Re-star the system.

Any question about the BIOS re-flash please contact your distributors or visit the web-site at below:

http://www.commell.com.tw/support/support.htm

42

LE-370 User’s Manual

Flash BIOS

(This Page is Left for Blank)

Flash BIOS

43

LE-370 User’s Manual

Hardware Test

 

 

 

Appendix C <Hardware Test>

C.1 <Power Consumption Test>

Hardware

Board

LE-370Z

 

CPU

Intel® Celeron® M 600MHz

 

Memory

Infineon DDR333 512MB x1

 

HDD

Hitachi IC25N080ATMR04 80GB

 

CDROM

SDR-038 4x DVD-ROM

(not counted)

Power Supply

SEVENTEAM ST-402HLP

 

Software

 

 

OS

Windows XP SP1 English Version

 

Application

3DMARK 2003

 

Test Result

 

 

 

Without LCD panel

24W

 

With 10.4” LCD panel

30W

 

With 15” LCD panel

38.4W

 

With 17” LCD panel

50W

44

Power Consumption Test

LE-370 User’s Manual

Contact Information

Contact Information

Any advice or comment about our products and service, or anything we can help you please don’t hesitate to contact with us. We will do our best to support you for your project and business.

Taiwan Commate Computer Inc.

Address

8F, No. 94, Sec. 1, Shin Tai Wu Rd., Shi Chih

 

Taipei Hsien, Taiwan

TEL

+886-2-26963909

FAX

+886-2-26963911

Website

http://www.commell.com.tw

E-Mail

info@commell.com.tw (General Information)

 

tech@commell.com.tw (Technical Support)

Commell is our trademark of industrial PC division

Contact Information

45