Intel D945GSEJT User Manual

3.31 Mb
Loading...

Intel® Desktop Board D945GSEJT

Product Guide

Order Number: E59413-002US

Revision History

Revision

Revision History

Date

-001

First release of the Intel® Desktop Board D945GSEJT

February 2009

 

Product Guide

 

 

 

 

-002

Second release of the Intel® Desktop Board D945GSEJT

May 2009

 

Product Guide

 

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124, 1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice.

Intel Desktop Board D945GSEJT may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling 1-800-548-4725.

Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries. * Other names and brands may be claimed as the property of others.

Copyright © 2009 Intel Corporation. All rights reserved.

Preface

This Product Guide gives information about board layout, component installation, and regulatory requirements for Intel® Desktop Board D945GSEJT.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for general audiences.

Intended Uses

All Intel® Desktop Boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:

1Desktop Board Features: a summary of product features

2Installing and Replacing Desktop Board Components: instructions on how to install the Desktop Board and other hardware components

3Updating the BIOS: a description of how to update the BIOS

ABIOS Error Messages: information about BIOS error messages and beep codes

BRegulatory Compliance: safety and EMC regulations and product certifications

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

iii

Intel Desktop Board D945GSEJT Product Guide

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term

Description

 

 

GB

Gigabyte (1,073,741,824 bytes)

 

 

GHz

Gigahertz (one billion hertz)

 

 

KB

Kilobyte (1024 bytes)

 

 

MB

Megabyte (1,048,576 bytes)

 

 

Mbit

Megabit (1,048,576 bits)

 

 

MHz

Megahertz (one million hertz)

 

 

iv

Contents

 

1

Desktop Board Features

 

 

Desktop Board Components.................................................................................

12

 

Processor..........................................................................................................

14

 

System Memory.................................................................................................

14

 

Mobile Intel® 945GSE Express Chipset ..................................................................

14

 

Intel 945GSE Graphics Subsystem ................................................................

15

 

Operating System Support ..................................................................................

16

 

Onboard Audio Subsystem ..................................................................................

16

 

Legacy Input/Output (I/O) Controller ....................................................................

17

 

Network Bootloader Support................................................................................

17

 

LAN Subsystem .................................................................................................

18

 

LAN Status LEDs.........................................................................................

18

 

USB 2.0 Support ................................................................................................

19

 

Mass Storage Support.........................................................................................

19

 

Expandability.....................................................................................................

20

 

BIOS................................................................................................................

20

 

ATA Auto Configuration ...............................................................................

20

 

PCI/PCI Express Auto Configuration ..............................................................

20

 

Security Passwords.....................................................................................

21

 

Power Management Features ...............................................................................

22

 

ACPI.........................................................................................................

22

 

Hardware Support ......................................................................................

22

 

ENERGY STAR*, e-Standby, and EuP Compliance....................................................

25

 

Battery.............................................................................................................

25

 

Real-Time Clock.................................................................................................

25

2

Installing and Replacing Desktop Board Components

 

 

Before You Begin ...............................................................................................

27

 

Installation Precautions.......................................................................................

28

 

Prevent Power Supply Overload ....................................................................

28

 

Observe Safety and Regulatory Requirements.................................................

28

 

Installing the I/O Shield ......................................................................................

29

 

Installing and Removing the Desktop Board ...........................................................

30

 

Installing System Memory ...................................................................................

31

 

Connecting SATA Drives......................................................................................

32

 

Installing a Wireless LAN Card in the PCI Express Full-Mini Card Slot .........................

34

 

Installing an Intel® Z-U130 USB Solid-State Drive (or Compatible Device)..................

35

 

Connecting to the Internal Headers and Connectors ................................................

36

 

Internal Connectors and Headers ..................................................................

37

 

Connecting a Chassis Fan ............................................................................

46

 

Setting the BIOS Configuration Jumper .................................................................

47

 

Clearing Passwords.....................................................................................

48

 

Replacing the Battery .........................................................................................

49

v

Intel Desktop Board D945GSEJT Product Guide

 

3

Updating the BIOS

 

 

Updating the BIOS with the Intel® Express BIOS Update Utility.................................

55

 

Updating the BIOS with the Iflash Memory Update Utility.........................................

56

 

Obtaining the BIOS Update File ....................................................................

56

 

Using the Iflash Memory Update Utility ..........................................................

56

 

Recovering the BIOS...................................................................................

57

A

Board Status and Error Messages

 

 

Front-panel Power LED Blink and Internal Speaker Beep Codes.................................

59

 

POST Error Messages..........................................................................................

60

B

Regulatory Compliance

 

 

Safety Standards ...............................................................................................

61

 

Place Battery Marking .................................................................................

61

 

European Union Declaration of Conformity Statement..............................................

62

 

Product Ecology Statements ................................................................................

63

 

Recycling Considerations .............................................................................

63

 

Lead-free 2LI/Pb-free 2LI Board ...................................................................

66

 

Restriction of Hazardous Substances (RoHS) ..................................................

67

 

EMC Regulations ................................................................................................

69

 

Ensure Electromagnetic Compatibility (EMC) Compliance..................................

70

 

Product Certifications..........................................................................................

71

 

Board-Level Certification Markings ................................................................

71

 

Chassis and Component Certifications............................................................

72

vi

 

 

Contents

Figures

 

1.

Intel Desktop Board D945GSEJT Components...................................................

12

2.

LAN Status LEDs ..........................................................................................

18

3.

Location of the Standby Power Indicator ..........................................................

23

4.

Installing the I/O Shield ................................................................................

29

5.

Intel Desktop Board D945GSEJT Mounting Screw Holes......................................

30

6.

Installing System Memory .............................................................................

31

7.

Removing System Memory.............................................................................

32

8.

Connecting the SATA Data and Power Cables....................................................

33

9.

Installing a Wireless LAN Card........................................................................

34

10.

Installing an Intel Z-U130 USB Solid-State Drive (or Compatible Device)..............

35

11.

Internal Headers and Connectors ....................................................................

36

12.

Connection Diagram for Front Panel Header .....................................................

43

13.

Connection Diagram for the Standard Front Panel USB Header............................

44

14.

Connection Diagram for the Front Panel USB Header with Intel Z-U130 USB

 

 

Solid-State Drive (or Compatible Device) Support .............................................

45

15.

Location of the Chassis Fan Header .................................................................

46

16.

BIOS Configuration Jumper Block....................................................................

47

17.

Removing the Battery ...................................................................................

53

18.

Intel Desktop Board D945GSEJT China RoHS Material Self Declaration Table.........

68

Tables

 

1.

Feature Summary..........................................................................................

9

2.

Intel Desktop Board D945GSEJT Components...................................................

13

3.

LAN Status LEDs ..........................................................................................

18

4.

ENERGY STAR Requirements ..........................................................................

25

5.

Internal Connectors and Headers ....................................................................

37

6.

Serial Port Header (COM 1 and COM 2)............................................................

37

7.

PS/2 Keyboard Port Header............................................................................

38

8.

PATA Connector (44-Pin) ...............................................................................

38

9.

Chassis Fan Header ......................................................................................

38

10.

Chassis Intrusion Header ...............................................................................

39

11.

SATA Power Connector..................................................................................

39

12.

Parallel Port Header ......................................................................................

39

13.

Front Panel Wireless Activity LED Header .........................................................

40

14.

S/PDIF Header .............................................................................................

40

15.

Internal Mono Speaker Header .......................................................................

40

16.

Front Panel Audio Header for Intel HD Audio.....................................................

40

17.

Front Panel Audio Header for AC ’97 Audio .......................................................

40

18.

Front Panel USB Header ................................................................................

41

19.

Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive

 

 

(or Compatible Device) Support) ....................................................................

41

20.

ATX12V Power Connector ..............................................................................

42

21.

Front Panel Header .......................................................................................

43

22.

States for a One-Color Power LED...................................................................

44

23.

Jumper Settings for the BIOS Setup Program Modes..........................................

48

24.

Acceptable Drives/Media Types for BIOS Recovery ............................................

57

25.

Front-panel Power LED Blink and Internal Speaker Beep Codes ...........................

59

26.

POST Error Messages ....................................................................................

60

27.

Safety Standards..........................................................................................

61

vii

Intel Desktop Board D945GSEJT Product Guide

 

28.

Lead-Free Second Level Interconnect Marks .....................................................

66

29.

China RoHS Environmentally Friendly Use Period Mark .......................................

67

30.

EMC Regulations...........................................................................................

69

31.

Product Certification Markings ........................................................................

71

viii

1 Desktop Board Features

This chapter briefly describes the main features of Intel® Desktop Board D945GSEJT. Table 1 summarizes the features of the Desktop Board.

Table 1. Feature Summary

Form Factor

Low-profile Mini-ITX (20 millimeters [0.79 inches] x 170 millimeters

 

[6.7 inches] x 170 millimeters [6.7 inches])

Processor

Passively-cooled, soldered-down Intel® Atomprocessor N270

Main Memory

One 200-pin Double Data Rate 2 (DDR2) Small Outline Dual Inline

 

 

Memory Module (SO-DIMM) socket with gold-plated contacts

 

Support for DDR2 533 MHz SO-DIMMs (DDR2 800 MHz and

 

 

DDR2 667 MHz validated to run at 533 MHz only)

 

Support for up to 2 GB of system memory

Chipset

Passively cooled mobile Intel® 945GSE Express Chipset consisting of:

 

Intel® 82945GSE Express Chipset Graphics and Memory Controller

 

 

Hub (GMCH)

 

Intel® 82801GBM I/O Controller Hub (ICH7-M)

Internal Graphics

Intel® Graphics Media Accelerator 950 (Intel® GMA 950) onboard

 

graphics subsystem with support for:

 

Analog displays (VGA)

 

Digital displays (DVI-D)

Audio

RealTek* ALC662 audio codec for 2 + 2-channel (multi-streaming)

 

Intel® High Definition Audio (Intel® HD Audio):

 

Front panel microphone/headphone header

 

S/PDIF digital audio header

 

Internal mono speaker header

Expansion

One PCI* bus add-in card connector

Capabilities

One PCI Express* Full-Mini Card slot

Peripheral

Seven USB 2.0 ports:

Interfaces

 

―Three back panel ports

 

 

―Four front panel ports (via two internal headers; one header

 

 

supports an Intel® Z-U130 USB Solid-State Drive (or compatible

 

 

device))

 

One parallel ATA (PATA) interface (44-pin) with ATA-100/66 support

 

Two Serial ATA (SATA) 3.0 Gb/s connectors (supporting IDE and

 

 

ACHI)

 

One SATA device power connector

Legacy I/O Control

Winbond* W83627DGH-A legacy I/O controller:

 

Two serial port headers

 

One parallel port header

 

One PS/2 keyboard header

Hardware Monitor

Hardware monitoring through the Winbond I/O controller

Subsystem

Voltage sense to detect out of range power supply voltages

 

Thermal sense to detect out of range thermal values

 

One fan header

 

One fan sense input used to monitor fan activity

 

Fan speed control

9

Intel Desktop Board D945GSEJT Product Guide

BIOS

Intel® BIOS

 

Support for Advanced Configuration and Power Interface (ACPI),

 

 

Plug and Play, and SMBIOS

LAN Support

10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem using a

 

 

RealTek* 8111DL Gigabit Ethernet Controller

Power

Integrated DC-to-DC circuitry

 

12 VDC jack on back panel for external power supply

 

ATX12V 2 x 2 power connector for alternate internal power supply

Power

Support for Advanced Configuration and Power Interface (ACPI)

Management

Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel

10

Desktop Board Features

For more information on Intel Desktop Board D945GSEJT consult the following online resources:

To find information

Visit this World Wide Web site:

about…

 

Intel Desktop Board

http://www.intel.com/products/motherboard/D945GSEJT/index.htm

D945GSEJT

 

Desktop Board Support

http://support.intel.com/support/motherboards/desktop

Available configurations

http://www.intel.com/products/motherboard/D945GSEJT/index.htm

for Intel Desktop Board

 

D945GSEJT

 

Chipset information

http://www.intel.com/products/desktop/chipsets/index.htm

BIOS and driver updates

http://downloadcenter.intel.com/

Integration information

http://www.intel.com/support/go/buildit

11

Intel Desktop Board D945GSEJT Product Guide

Desktop Board Components

Figure 1 shows the location of the major components on Intel Desktop Board D945GSEJT.

Figure 1. Intel Desktop Board D945GSEJT Components

12

Desktop Board Features

Table 2. Intel Desktop Board D945GSEJT Components

Label

Description

 

 

A

Back panel connectors

 

 

B

12 V processor core voltage connector (2 x 2)

 

 

C

SO-DIMM Connector

 

 

D

Intel 82945GSE GMCH

 

 

E

Intel Atom processor N270

 

 

F

Serial port (COM 2)

 

 

G

Serial port (COM 1)

 

 

H

PS/2 keyboard port header

 

 

I

Reserved

 

 

J

PATA connector (44 pin)

 

 

K

Reserved

 

 

L

Chassis fan header

 

 

M

Chassis intrusion header

 

 

N

SATA 0 connector

 

 

O

SATA power connector

 

 

P

SATA 1 connector

 

 

Q

Intel 82801GBM I/O Controller Hub (ICH7-M)

 

 

R

Parallel port header

 

 

S

Reserved

 

 

T

Reserved

 

 

U

Front panel header

 

 

V

Front panel wireless activity LED header

 

 

W

PCI Express Mini Card connector

 

 

X

BIOS configuration jumper block

 

 

Y

PCI bus connector

 

 

Z

S/PDIF header

 

 

AA

Front panel USB header

 

 

BB

Internal mono speaker header

 

 

CC

Front panel audio header

DDFront panel USB header with Intel Z-U130 USB Solid-State Drive (or compatible device) support

13

Intel Desktop Board D945GSEJT Product Guide

Processor

Intel Desktop Board D945GSEJT includes an Intel Atom processor N270. The processor is soldered to the Desktop Board and is not customer upgradeable.

NOTE

The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the processor heatsink area for maximum heat dissipation effectiveness.

System Memory

NOTE

To be fully compliant with all applicable Intel® SDRAM memory specifications, the board should be populated with an SO-DIMM that supports the Serial Presence Detect (SPD) data structure. If the SO-DIMM does not support SPD, you will see a notification to this effect on the screen at power up. The BIOS will attempt to configure the memory controller for normal operation.

The Desktop Board has one 200-pin DDR2 SO-DIMM connector with gold-plated contacts. It supports:

533 MHz unbuffered, non-registered DDR2 SO-DIMMs

Serial Presence Detect (SPD) memory only

Non-ECC memory

Up to 2 GB of memory

Mobile Intel® 945GSE Express Chipset

The Mobile Intel 945GSE Express Chipset consists of the following devices:

Intel 82945GSE Express Chipset Graphics and Memory Controller Hub (GMCH) with Direct Media Interface (DMI) interconnect

Intel 82801GBM I/O Controller Hub (ICH7-M) with DMI

The GMCH component provides interfaces to the processor, memory, and the DMI interconnect. This component also provides integrated graphics capabilities via the Intel® Graphics Media Accelerator 950 (Intel® GMA 950).

The ICH7 is a centralized controller for the board’s I/O paths. For more information about the Intel 945GSE Express Chipset, go to http://www.intel.com/design/chipsets/embedded/945gse/

NOTE

The board is designed to be passively cooled in a properly ventilated chassis. Chassis venting locations are recommended above the GMCH heatsink area for maximum heat dissipation effectiveness.

14

Desktop Board Features

Intel 945GSE Graphics Subsystem

Intel® GMA950 Graphics Controller

The Intel GMA950 graphics controller features the following:

166 MHz core frequency

High performance 3-D setup and render engine

High quality texture engine

DX9* Compliant Hardware Pixel Shader 2.0

Alpha and luminance maps

Texture color-keying/chroma-keying

Cubic environment reflection mapping

Enhanced texture blending functions

3D Graphics Rendering enhancements

1.3 Dual Texture GigaPixel/second Fill Rate

16 and 32 bit color

Maximum 3D supported resolution of 1600 x 1200 x 32 at 85 Hz

Vertex cache

Anti-aliased lines

OpenGL* version 1.4 support with vertex buffer and EXT_Shadow extensions

2D Graphics enhancements

8, 16, and 32 bit color

Optimized 256-bit BLT engine

Color space conversion

Anti-aliased lines

Video

Hardware motion compensation for MPEG2

Software DVD at 30 fps full screen

Intel® Zoom Utility

Video Memory Allocation

Video memory is allocated from the total available system memory for the efficient balancing of 2-D/3-D graphics performance and overall system performance. Dynamic allocation of system memory to video memory is as follows:

256 MB total RAM results in 32 MB video RAM

512 MB total RAM results in 64 MB video RAM

1 GB total RAM results in 128 MB video RAM

2 GB total RAM results in 224 MB video RAM

Analog Display (VGA) Support

The VGA port supports analog displays. The maximum supported resolution is 2048 x 1536 (QXGA) at a 75 Hz refresh rate.

15

Intel Desktop Board D945GSEJT Product Guide

Digital Visual Interface (DVI) Support

The DVI-D port supports digital DVI displays. The maximum supported resolution is 1600 x 1200 (UXGA). The DVI port is compliant with the DVI 1.0 specification.

NOTE

The default monitor can be dynamically switched with the following keyboard hotkeys:

<Ctrl+Alt+F1> for VGA

<Ctrl+Alt+F4> for DVI

Operating System Support

The following Microsoft* 32-bit operating systems are fully supported by the Desktop Board:

Microsoft Windows Vista* Home Basic

Microsoft Windows Vista Business

Microsoft Windows* XP Home

Microsoft Windows XP Professional

The board has also been validated against the following Linux distributions:

SUSE* Linux Enterprise Desktop

Red Hat* ENTERPRISE LINUX*

Ubuntu

Onboard Audio Subsystem

Intel Desktop Board D945GSEJT has a 2 + 2-channel (stereo) onboard audio subsystem that includes a Realtek ALC662 audio codec.

The subsystem includes the following headers and connectors:

Front panel audio header (supports both AC ’97 and Intel HD Audio) , including functionality for:

Line out

Microphone in

Back panel audio line-out connector

S/PDIF header (3 pin)

Internal mono speaker header (2 pin) for support of a 1.5 W/ 8 Ω speaker

The front/back panel audio connectors are configurable through the audio device drivers.

16

Desktop Board Features

The audio stream for the line-out port is routed according to the following dependencies:

By default, the audio stream is down-mixed to mono and amplified for an internal mono speaker.

If a connection is detected at the back panel line-out port, the audio stream is sent to the rear line-out port and the internal mono speaker is disabled.

NOTE

The back panel audio line out connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to this output.

Legacy Input/Output (I/O) Controller

The legacy I/O controller features the following:

Two serial ports

One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support

Serial IRQ interface compatible with serialized IRQ support for PCI systems

PS/2-style keyboard interface

Intelligent power management, including a programmable wake up event interface

PCI power management support

Network Bootloader Support

The LAN subsystem supports the traditional Pre-Execution Environment (PXE) as well as the open-source gPXE (http://etherboot.org/) network bootloaders.

gPXE is an open source network bootloader providing traditional PXE environment compatibility and additional protocol support, such as TCP, HTTP, DNS and iSCSI. Refer to http://etherboot.org/ for further information.

System deployments where gPXE features are leveraged allow for diskless client configurations, eliminating the power consumption, thermal, acoustic, and cost disadvantages of having a local storage device per station.

NOTE

gPXE source code is available on the Intel® Express Installer Drivers DVD shipped with the desktop board, as well as upon request.

17

Intel Desktop Board D945GSEJT Product Guide

LAN Subsystem

The LAN subsystem consists of the following:

Intel 82801GBM ICH7-M

Realtek 8111D Gigabit Ethernet Controller for 10/100/1000 Mbits/sec Ethernet LAN connectivity

RJ-45 LAN connector with integrated status LEDs

Additional features of the LAN subsystem include:

CSMA/CD protocol engine

LAN connect interface that supports the ethernet controller

PCI bus power management

Supports ACPI technology

Supports LAN wake capabilities

LAN drivers are available from Intel’s World Wide Web site at

http://downloadcenter.intel.com/.

LAN Status LEDs

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2). These LEDs indicate the operating states of the LAN.

Figure 2. LAN Status LEDs

Table 3 describes the LED states when the board is powered up and the LAN subsystem is operating.

Table 3. LAN Status LEDs

LED

LED Color

LED State

Indicates

 

 

 

 

 

N/A

Off

LAN link is not established.

Link (A)

 

 

 

Green

On (steady state)

LAN link is established.

 

 

 

 

Blinking

LAN activity is occurring.

 

 

 

 

 

 

 

N/A

Off

10 Mbits/s data rate is selected.

Speed (B)

 

 

 

Green

On (steady state)

100 Mbits/s data rate is selected.

 

 

 

 

 

Yellow

On (steady state)

1000 Mbits/s data rate is selected.

 

 

 

 

18

Desktop Board Features

USB 2.0 Support

The Desktop Board supports up to seven USB 2.0 ports (three ports routed to the back panel and four ports routed to two front panel USB 2.0 headers). One of the front panel USB headers supports an Intel Z-U130 USB Solid-State Drive (or compatible device). The USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling High-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0.

NOTE

Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device.

Mass Storage Support

The board provides three ATA connectors that can be used to add storage capability to the board. The following connectors are included:

One PATA connector that supports two devices

Two SATA connectors that support one device per connector

PATA Interface

The ICH7-M’s PATA controller has one bus-mastering PATA interface that is accessible through a 44-pin connector that is compatible with 2.5 or 3.5 inch PATA hard drives (including power support for 2.5 inch hard drives). The PATA interface supports the following modes:

Programmed I/O (PIO)

8237-style DMA

Ultra DMA

ATA-66

ATA-100

NOTE

ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce reflections, noise, and inductive coupling.

The PATA interface also supports ATAPI devices (such as CD-ROM drives) and ATA devices using the transfer modes.

The BIOS supports Logical Block Addressing (LBA) and Extended Cylinder Head Sector (ECHS) translation modes. The drive reports the transfer rate and translation mode to the BIOS.

19

Intel Desktop Board D945GSEJT Product Guide

SATA Interface

The Desktop Board supports two Serial ATA channels (3.0 Gb/s) that support one device per channel. The SATA controller supports IDE and ACHI configuration and can operate in both legacy and native modes.

Expandability

The Desktop Board provides the following expansion capability:

One PCI connector. The connector can support either a single PCI add-in card or a singleor dual-slot PCI riser card.

One PCI Express Full-Mini Card slot.

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI and IDE auto-configuration utilities, and the video BIOS.

ATA Auto Configuration

If you install an ATA device (such as a hard drive) in your computer, the autoconfiguration utility in the BIOS automatically detects and configures the device for your computer. You do not need to run the BIOS Setup program after installing an ATA device. You can override the auto-configuration options by specifying manual configuration in the BIOS Setup program.

PCI/PCI Express Auto Configuration

If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express auto-configuration utility in the BIOS automatically detects and configures the resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

20

Desktop Board Features

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup and for booting the computer, with the following restrictions:

The supervisor password gives unrestricted access to view and change all Setup options. If only the supervisor password is set, pressing <Enter> at the password prompt of Setup gives the user restricted access to Setup.

If both the supervisor and user passwords are set, you must enter either the supervisor password or the user password to access Setup. Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered.

Setting a user password restricts who can boot the computer. The password prompt is displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, you can enter either password to boot the computer.

For instructions on resetting the password, see Clearing Passwords on page 48.

21

Intel Desktop Board D945GSEJT Product Guide

Power Management Features

Power management is implemented at several levels, including:

Advanced Configuration and Power Interface (ACPI)

Hardware support:

Fan header

+5 V standby power indicator LED

LAN Wake capabilities

Instantly Available PC technology

Wake from USB

Wake from PS/2 keyboard/mouse

PME# wakeup support

WAKE# signal wakeup support

ACPI

ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with the Desktop Board requires an operating system that provides full ACPI support.

Hardware Support

Fan Header

The Desktop Board has a 3-pin chassis fan header. See Figure 15 on page 46 for the location of the chassis fan header.

+5 V Standby Power Indicator LED

CAUTION

If the AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is standby power to the system. This includes the DIMM socket and the PCI bus connector, even though the computer appears to be off.

22

Desktop Board Features

Figure 3. Location of the Standby Power Indicator

For more information on standby current requirements for the Desktop Board, refer to the Technical Product Specification on the Intel Desktop D945GSEJT web page at http://www.intel.com/products/motherboard/D945GSEJT/index.htm.

23

Intel Desktop Board D945GSEJT Product Guide

Instantly Available PC Technology

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to- RAM) sleep-state. While in the ACPI S3 sleep-state, the computer will appear to be off (the hard drive(s) and fan will power off, the front panel power LED will blink). When signaled by a wake-up device or event, the system quickly returns to its last known state.

The board supports the PCI Bus Power Management Interface Specification. Add-in boards that also support this specification can participate in power management and can be used to wake the computer.

The use of Instantly Available PC technology requires operating system support and PCI 2.3 compliant add-in cards and drivers.

LAN Wake Capabilities

The board’s LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem network adapter monitors network traffic at the Media Independent Interface. The board supports LAN wake capabilities with ACPI in the following ways:

By Ping

By Magic Packet

Upon detecting the configured wake packet type, the LAN subsystem asserts a wakeup signal that powers up the computer.

Wake from USB

USB bus activity wakes the computer from an ACPI S1 or S3 state.

NOTE

Wake from USB requires the use of a USB peripheral that supports wake from USB.

Wake from PS/2 Device

PS/2 keyboard activity wakes the computer from an ACPI S1, S3, S4, or S5 state. However, when the computer is in an ACPI S4 or S5 state, the only PS/2 activity that will wake the computer is the power key available only on some keyboards.

PME# Wakeup Support

When the PME# signal is asserted on the PCI bus, the computer wakes from an ACPI S1, S3, S4, or S5 state.

WAKE# Signal Wakeup Support

When the WAKE# signal is asserted on the PCI Express bus, the computer wakes from an ACPI S1, S3, S4, or S5 state.

24

Desktop Board Features

ENERGY STAR*, e-Standby, and EuP

Compliance

Intel Desktop Board D945GSEJT meets the ENERGY STAR requirements listed in Table 4 when used in corresponding system configurations.

Table 4. ENERGY STAR Requirements

 

 

 

 

 

Typical

 

 

 

 

 

Electricity

 

ENERGY STAR

 

Required

Capability

Consumption

 

Specification

Computer Type

States

Adjustments

(TEC) Criteria

 

 

 

 

 

 

 

v4.0

Desktop Computer

Idle State

With and

N/A

 

 

 

(Cat A)

without Wake

 

 

v4.0

Integrated

 

 

Sleep Mode

On LAN (Sleep,

 

 

 

Computer

 

 

 

Standby)

 

 

 

 

 

 

 

 

Standby Level

 

 

 

 

 

 

 

 

 

 

 

 

 

v5.0

Desktop Computer

Off Mode

With and

Cat A under

 

 

 

Sleep Mode

without

“desktop

 

v5.0

Integrated Desktop

 

additional

conventional”

 

 

 

 

Computer

Idle State

 

 

internal storage

and “desktop

 

 

 

 

 

 

 

Active State

 

proxying”

 

 

 

 

 

operational

 

 

 

 

 

mode

 

 

 

 

 

weightings

 

 

 

 

 

 

 

v5.0

Thin Client

Off Mode

With and

N/A

 

 

 

Sleep Mode

without Wake

 

 

 

 

On LAN (Sleep,

 

 

 

 

Idle State

 

 

 

 

Standby)

 

 

 

 

(Cat B)

 

 

 

 

 

 

 

 

 

 

 

 

For information about ENERGY STAR requirements and recommended configurations, go to http://www.intel.com/go/energystar.

The Desktop Board also meets the following international requirements:

Republic of Korea e-Standby program

European Union Energy using Products (EuP) directive

Battery

A coin-cell battery on the Desktop Board keeps the values in CMOS RAM and the clock current when the computer is turned off. Go to page 49 for instructions on how to replace the battery.

Real-Time Clock

The Desktop Board includes a time-of-day clock and a 100-year calendar. The coincell battery keeps the clock current when the computer is turned off.

25

Intel Desktop Board D945GSEJT Product Guide

26

2Installing and Replacing Desktop Board Components

This chapter tells you how to:

Install the I/O shield

Install and remove the Desktop Board

Install and remove system memory

Connect SATA drives

Install a Wireless LAN card

Install an Intel Z-U130 USB Solid-State Drive (or compatible device)

Connect to internal headers

Connect a chassis fan cable

Set the BIOS configuration jumper

Clear passwords

Replace the battery

Before You Begin

CAUTIONS

The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment.

Disconnect the computer from its power source and from any telecommunications links, networks, or modems before performing any of the procedures described in this chapter. Failure to disconnect power, telecommunications links, networks, or modems before you open the computer or perform any procedures can result in personal injury or equipment damage. Some circuitry on the board can continue to operate even though the front panel power button is off.

Follow these guidelines before you begin installing the Desktop Board:

Always follow the steps in each procedure in the correct order.

Set up a log to record information about your computer, such as model, serial numbers, installed options, and configuration information.

Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

27

Intel Desktop Board D945GSEJT Product Guide

Installation Precautions

When you install and test the Intel Desktop Board, observe all warnings and cautions in the installation instructions.

To avoid injury, be careful of:

Sharp pins on connectors or headers

Sharp pins on printed circuit assemblies

Rough edges and sharp corners on the chassis

Hot components (such as voltage regulators and heat sinks)

Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel.

Prevent Power Supply Overload

Do not overload the power supply output. To avoid overloading the power supply, make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of the power supply.

Observe Safety and Regulatory Requirements

Read and adhere to the instructions in this section and the instructions supplied with the chassis and associated modules. If you do not follow these instructions and the instructions provided by chassis and module suppliers, you increase safety risk and the possibility of noncompliance with regional laws and regulations.

Refer to Appendix B for safety and regulatory requirements.

28

Installing and Replacing Desktop Board Components

Installing the I/O Shield

The Desktop Board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis.

Install the I/O shield before installing the Desktop Board in the chassis. Place the shield inside the chassis as shown in Figure 4. Press the shield into place so that it fits tightly and securely. If the shield does not fit, obtain a properly-sized shield from the chassis supplier.

Figure 4. Installing the I/O Shield

29

Intel Desktop Board D945GSEJT Product Guide

Installing and Removing the Desktop Board

CAUTION

Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage.

Refer to your chassis manual for instructions on installing and removing the Desktop Board.

Figure 5 shows the location of the mounting screw holes for Intel Desktop Board D945GSEJT.

Figure 5. Intel Desktop Board D945GSEJT Mounting Screw Holes

30

Installing and Replacing Desktop Board Components

Installing System Memory

NOTE

To be fully compliant with all applicable Intel SDRAM memory specifications, the board requires SO-DIMMs that support the Serial Presence Detect (SPD) data structure.

The Desktop Board has one 200-pin DDR2 SO-DIMM socket that supports up to 2 GB of system memory. To install system memory on the Desktop Board, see Figure 6 and follow these steps:

1.Observe the precautions in "Before You Begin" on page 27.

2.Install the SO-DIMM in the socket. Hold the DIMM with the back edge tilted slightly upwards, insert the SO-DIMM into the socket, and gently push the back edge of the SO-DIMM down until it snaps into the retention arms.

Figure 6. Installing System Memory

31

Intel Desktop Board D945GSEJT Product Guide

To remove an SO-DIMM from the socket, gently spread the socket’s retention arms as shown in Figure 7 to disengage them from the SO-DIMM.

Figure 7. Removing System Memory

Connecting SATA Drives

Intel Desktop Board D945GSEJT supports two SATA drives with two data connectors. The board ships with an in-line power cable that provides:

a right-angled female-gender 1 x 4 connector for low-profile board connectivity

a 15-pin SATA power connector for SATA drive power

a female-gender 1 x 4 connector for system component power flexibility

To connect a SATA drive to the Desktop Board:

1.Observe the precautions in "Before You Begin" on page 27.

2.Attach one end of the SATA data cable to a SATA connector on the board (Figure 8, A).

3.Attach the other end of the SATA data cable to the SATA drive (Figure 8, B).

4.Attach the right-angled 4-pin power connector on the power cable to the 4-pin connector on the Desktop Board (Figure 8, C).

5.Attach the SATA power connector (Figure 8, D) on the power cable to the mating connector on a SATA drive.

32

Installing and Replacing Desktop Board Components

Figure 8. Connecting the SATA Data and Power Cables

33

Intel Desktop Board D945GSEJT Product Guide

Installing a Wireless LAN Card in the PCI Express Full-Mini Card Slot

A wireless LAN card can be installed in the Desktop Board’s PCI Express Full-Mini Card slot.

To install a wireless LAN card on the Desktop Board, see Figure 9 and follow these steps:

1.Observe the precautions in "Before You Begin" on page 27.

2.Locate the PCI Express Full-Mini Card slot (Figure 1, W).

3.Insert the wireless LAN card into the PCI Express Mini Card connector (Figure 9, A) at a slightly upward angle.

4.Align the mounting holes (Figure 9, B) and snap the card in place.

5.Attach your system’s antenna wires to the connectors (Figure 9, C) on the wireless LAN card as shown.

NOTE

External antennas can be connected through the I/O shield by removing any or all of the cut-outs above the back panel I/O section.

Figure 9. Installing a Wireless LAN Card

34

Installing and Replacing Desktop Board Components

Installing an Intel® Z-U130 USB Solid-State

Drive (or Compatible Device)

An Intel Z-U130 USB Solid-State Drive (or compatible device) can be installed on the Desktop Board by using the onboard USB 2.0 header indicated in Figure 1, DD. This header provides support for the solid state drive.

To install an Intel Z-U130 USB Solid-State Drive (or compatible device) on the Desktop Board, follow these steps:

1.Observe the precautions in "Before You Begin" on page 27.

2.Align the connector (Figure 10, A) on the bottom of the solid state drive with the USB 2.0 header on the Desktop Board. The connectors are keyed and will mate correctly when the solid state drive is oriented as shown in Figure 10.

3.Secure the solid state drive to the Desktop Board with the screw (Figure 10, B) included with the drive.

Figure 10. Installing an Intel Z-U130 USB Solid-State Drive

(or Compatible Device)

35

Intel Desktop Board D945GSEJT Product Guide

Connecting to the Internal Headers and Connectors

Before connecting cables to the internal headers or connectors, observe the precautions in "Before You Begin" on page 27. Figure 11 shows the location of the board’s internal connectors and headers; Table 5 describes the internal connectors and headers identified in Figure 11.

Figure 11. Internal Headers and Connectors

36

Installing and Replacing Desktop Board Components

Table 5. Internal Connectors and Headers

Item Description

A+12 V internal power connector (ATX12V)

BSerial port header (COM 2)

CSerial port header (COM 1)

DPS/2 keyboard port header

EReserved

FPATA connector (44-pin)

GReserved

HChassis fan header

IChassis intrusion header

JSATA connectors

K

SATA power connector

 

 

L

Parallel port header

MReserved

NReserved

OFront panel header

P

Front panel wireless activity LED header

QPCI Express Mini Card connector

RPCI bus add-in card connector

SS/PDIF header

T Front panel USB header

UInternal mono speaker header

VFront panel audio header

WFront panel USB header with Intel Z-U130 USB Solid-State Drive (or compatible device) support

Internal Connectors and Headers

Table 6 through Table 21 list the signal names for the connectors and headers in Figure 11 and Table 5.

Table 6. Serial Port Header (COM 1 and COM 2)

Pin

Signal Name

 

 

1

DCD (Data Carrier Detect)

 

 

3

TXD# (Transmit Data)

 

 

5

Ground

 

 

7

RTS (Request To Send)

 

 

9

RI (Ring Indicator)

 

 

Pin

Signal Name

 

 

2

RXD# (Receive Data)

 

 

4

DTR (Data Terminal Ready)

 

 

6

DSR (Data Set Ready)

 

 

8

CTS (Clear To Send)

 

 

10

Key (no pin)

 

 

37

Intel Desktop Board D945GSEJT Product Guide

Table 7. PS/2 Keyboard Port Header

Pin

Signal Name

Pin

Signal Name

 

 

 

 

1

Data

2

Key (no pin)

 

 

 

 

3

Ground

4

+5V

 

 

 

 

5

Clock

6

Key (no pin)

 

 

 

 

Table 8. PATA Connector (44-Pin)

Pin

Signal Name

 

 

1

#Reset

 

 

3

Data 7

 

 

5

Data 6

 

 

7

Data 5

 

 

9

Data 4

 

 

11

Data 3

 

 

13

Data 2

 

 

15

Data 1

 

 

17

Data 0

 

 

19

GND

 

 

21

DMA Request

 

 

23

#IOW

 

 

25

#IOR

 

 

27

IO Chrdy

 

 

29

DMA Acknowledge

 

 

31

IRQ14

 

 

33

Addr 1

 

 

35

Addr 0

 

 

37

#CS0 (1F0-1F7)

 

 

39

#Active (LED driver)

 

 

41

+5V_DC (logic)

 

 

43

GND

 

 

Pin

Signal Name

 

 

2

GND

 

 

4

Data 8

 

 

6

Data 9

 

 

8

Data 10

 

 

10

Data 11

 

 

12

Data 12

 

 

14

Data 13

 

 

16

Data 14

 

 

18

Data 15

 

 

20

Key (no pin)

 

 

22

GND

 

 

24

GND

 

 

26

GND

 

 

28

Cable Select

 

 

30

GND

 

 

32

#IOCS16

 

 

34

Passed Diagnostics

 

 

36

Addr 2

 

 

38

#CS1 (3f6-3f7)

 

 

40

GND

 

 

42

+5V_DC (motor)

 

 

44

Type (GND = ATA)

 

 

Table 9. Chassis Fan Header

Pin

Signal Name

1Control

2+12 V

3Tach

38

Installing and Replacing Desktop Board Components

Table 10. Chassis Intrusion Header

Pin

Signal Name

1Intruder#

2Ground

Table 11. SATA Power Connector

Pin

Signal Name

1+12 VDC

2Ground

3Ground

4+5 VDC

Table 12. Parallel Port Header

Pin

Standard Signal Name

ECP Signal Name

EPP Signal Name

 

 

 

 

1

STROBE#

STROBE#

WRITE#

 

 

 

 

2

AUTOFD#

AUTOFD#, HOSACK

DATASTB#

 

 

 

 

3

PD0

PD0

PD0

 

 

 

 

4

FAULT#

FAULT#, PERIPHREQST#

FAULT#

 

 

 

 

5

PD1

PD1

PD1

 

 

 

 

6

INT#

INT#, REVERSERQST#

RESET#

 

 

 

 

7

PD2

PD2

PD2

 

 

 

 

8

SLCTIN#

SLCTIN#

ADDRSTB#

 

 

 

 

9

PD3

PD3

PD3

 

 

 

 

10

GROUND

GROUND

GROUND

 

 

 

 

11

PD4

PD4

PD4

 

 

 

 

12

GROUND

GROUND

GROUND

 

 

 

 

13

PD5

PD5

PD5

 

 

 

 

14

GROUND

GROUND

GROUND

 

 

 

 

15

PD6

PD6

PD6

 

 

 

 

16

GROUND

GROUND

GROUND

 

 

 

 

17

PD7

PD7

PD7

 

 

 

 

18

GROUND

GROUND

GROUND

 

 

 

 

19

ACK#

ACK#

INTR

 

 

 

 

20

GROUND

GROUND

GROUND

 

 

 

 

21

BUSY

BUSY#, PERIPHACK

WAIT#

 

 

 

 

22

GROUND

GROUND

GROUND

 

 

 

 

23

PERROR

PE, ACKREVERSE#

PE

 

 

 

 

24

GROUND

GROUND

GROUND

 

 

 

 

25

SELECT

SELECT

SELECT

 

 

 

 

26

KEY (no pin)

KEY (no pin)

KEY (no pin)

 

 

 

 

39

Intel Desktop Board D945GSEJT Product Guide

Table 13. Front Panel Wireless Activity LED Header

Pin

Signal Name

1LED (+)

2Ground

Table 14. S/PDIF Header

Pin

Signal Name

1Ground

2S/PDIF out

3VCC (5V)

Table 15. Internal Mono Speaker Header

Pin

Signal Name

1+

2

Table 16. Front Panel Audio Header for Intel HD Audio

Pin

Signal Name

 

 

1

[Port 1] Left channel

 

 

3

[Port 1] Right channel

 

 

5

[Port 2] Right channel

 

 

7

SENSE_SEND (Jack detection)

 

 

9

[Port 2] Left channel

 

 

Pin

Signal Name

 

 

2

Ground

 

 

4

PRESENCE# (Dongle present)

 

 

6

[Port 1] SENSE_RETURN

 

 

8

Key (no pin)

 

 

10

[Port 2] SENSE_RETURN

 

 

Table 17. Front Panel Audio Header for AC ’97 Audio

Pin

Signal Name

Pin

Signal Name

 

 

 

 

1

MIC

2

AUD_GND

 

 

 

 

3

MIC_BIAS

4

AUD_GND

 

 

 

 

5

FP_OUT_R

6

FP_RETURN_R

 

 

 

 

7

AUD_5V

8

KEY (no pin)

 

 

 

 

9

FP_OUT_L

10

FP_RETURN_L

 

 

 

 

40

Installing and Replacing Desktop Board Components

Table 18. Front Panel USB Header

Pin

Signal Name

Pin

Signal Name

 

 

 

 

1

+5 VDC

2

+5 VDC

 

 

 

 

3

D-

4

D-

 

 

 

 

5

D+

6

D+

 

 

 

 

7

Ground

8

Ground

 

 

 

 

9

KEY (no pin)

10

No Connect

 

 

 

 

Table 19. Front Panel USB Header (with Intel Z-U130 USB Solid-State Drive (or Compatible Device) Support)

Pin

Signal Name

Pin

Signal Name

 

 

 

 

1

+5 VDC

2

+5 VDC

 

 

 

 

3

D-

4

D-

 

 

 

 

5

D+

6

D+

 

 

 

 

7

Ground

8

Ground

 

 

 

 

9

KEY (no pin)

10

LED#

 

 

 

 

Add-in Card Connectors

The board has the following add-in card connectors:

PCI Express Mini Card (revision 1.2 compliant) connector

PCI (revision 2.3 compliant) bus connector

Note the following considerations for the PCI bus connector:

The PCI bus connector is bus master capable.

SMBus signals are routed to the PCI bus connector. This enables PCI bus add-in boards with SMBus support to access sensor data on the board. The specific SMBus signals are as follows:

The SMBus clock line is connected to pin A40.

The SMBus data line is connected to pin A41.

The PCI bus connector also supports single-slot and dual-slot riser cards for use of up to two bus master PCI expansion cards. In order to support two PCI bus master expansion cards, the riser card must support the following PCI signal routing:

Pin A11: additional 33 MHz PCI clock

Pin B10: additional PCI request signal (i.e., PREQ#2)

Pin B14: additional PCI Grant signal (i.e., GNT#2)

41

Intel Desktop Board D945GSEJT Product Guide

Power Supply Connectors

The board has the following power supply connectors:

External Power Supply – the board can be powered with a 12 V external power supply though a DC connector on the back panel. The rear 12 VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of

5.5 mm, where the inner contact is 12 V and the shell is GND.

Internal Power Supply – the board can alternatively be powered via an ATX12V 2 x 2 power connector. The signal names for the ATX12V power connector are shown in Table 20

Table 20. ATX12V Power Connector

Pin

Signal Name

 

 

1

Ground

 

 

3

+12 V

 

 

Pin

Signal Name

 

 

2

Ground

 

 

4

+12 V

 

 

NOTE

Use of an external 12 VDC power supply is preferred.

The recommended power rating is 60 W (12 V/5 A) for general purpose use. Total power consumption will depend on the system configuration selected by the integrator; refer to Intel Desktop Board D945GSEJT Technical Product Specification for further guidance.

CAUTION

The external 12 VDC jack is the primary power input connector of Intel Desktop Board D945GSEJT. However, the Desktop Board also provides an internal 2 x 2 power connector that can used be with a target system that already has an internal power supply.

There is no isolation circuitry between the external 12 VDC jack and the internal 2 x 2 power connector. It is the system integrator’s responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12 VDC jack is covered if the internal 2 x 2 power connector is to be used.

Simultaneous connection of both external and internal power supply units could result in potential damage to the desktop board, power supplies, or other hardware.

Front Panel Header

This section describes the functions of the front panel header. Table 21 lists the signal names of the front panel header. Figure 12 is a connection diagram for the front panel header.

42

Installing and Replacing Desktop Board Components

Table 21. Front Panel Header

 

 

In/

 

 

 

In/

 

Pin

Signal

Out

Description

Pin

Signal

Out

Description

 

 

 

 

 

 

 

 

 

Hard Drive Activity LED

 

Power LED

 

 

 

 

 

 

 

 

 

1

HD_PWR

Out

Hard disk LED

2

HDR_BLNK_GR

Out

Front panel

 

 

 

pull-up to +5 V

 

N

 

green LED

 

 

 

 

 

 

 

 

3

HDA#

Out

Hard disk active

4

HDR_BLNK_YE

Out

Front panel

 

 

 

LED

 

L

 

yellow LED

 

 

 

 

 

 

 

 

 

Reset Switch

 

On/Off Switch

 

 

 

 

 

 

 

 

 

 

5

Ground

 

Ground

6

FPBUT_IN

In

Power switch

 

 

 

 

 

 

 

 

 

 

7

FP_RESET#

In

Reset switch

8

Ground

 

Ground

 

 

 

 

 

 

 

 

 

 

 

Power

 

 

Not Connected

 

 

 

 

 

 

 

 

 

9

+5 V

 

Power

10

N/C

 

Not connected

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 12. Connection Diagram for Front Panel Header

Hard Drive Activity LED Pins

Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. Proper LED function requires one of the following:

A SATA hard drive connected to an onboard SATA connector

A PATA hard drive connected to an onboard PATA connector

Intel Z-U130 USB Solid State Drive (or compatible device) connected to one of the front panel USB headers

Reset Switch Pins

Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST.

43

Intel Desktop Board D945GSEJT Product Guide

Power/Sleep LED Pins

Pins 2 and 4 can be connected to a oneor two-color LED. Table 22 shows the possible states for a one-color power LED.

Table 22. States for a One-Color Power LED

LED State

Description

 

 

Off

Power off/hibernate (S5/S4)

 

 

Blinking

Sleeping (S3)

 

 

Steady Green

Running/Away (S0/S1)

 

 

NOTE

The LED states listed in Table 22 are default settings and can be modified through the BIOS setup. Systems built with a dual-color front panel power LED can also use alternate color state options.

Power Switch Pins

Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal.

Front Panel USB Headers

Figure 13 is a connection diagram for the standard front panel USB header (see Figure 11, T).

Figure 13. Connection Diagram for the Standard Front Panel USB Header

44

Installing and Replacing Desktop Board Components

Figure 14 is a connection diagram for the front panel USB header (see Figure 11, W).

Figure 14. Connection Diagram for the Front Panel USB Header with Intel Z-U130 USB Solid-State Drive (or Compatible Device) Support

45

Intel Desktop Board D945GSEJT Product Guide

Connecting a Chassis Fan

Figure 15 shows the location of the chassis fan header. Connect the chassis fan cable to this header.

Figure 15. Location of the Chassis Fan Header

46

Installing and Replacing Desktop Board Components

Setting the BIOS Configuration Jumper

NOTE

Always turn off the power and unplug the power cord from the computer before changing a jumper. Moving the jumper with the power on may result in unreliable computer operation.

Figure 16 shows the location of the Desktop Board’s BIOS configuration jumper block.

Figure 16. BIOS Configuration Jumper Block

The three-pin BIOS jumper block enables board operating modes. Table 23 shows the jumper settings for each of the available modes.

47

Intel Desktop Board D945GSEJT Product Guide

Figure 16 shows the location of the Desktop Board’s BIOS configuration jumper block.

Table 23. Jumper Settings for the BIOS Setup Program Modes

Jumper

 

 

Setting

Mode

Description

 

 

 

 

Normal (default) (1-2)

The BIOS uses the current configuration and

 

 

passwords for booting.

 

 

 

 

Configure (2-3)

After the Power-On Self-Test (POST) runs, the

 

 

BIOS displays the Maintenance Menu. Use this

 

 

menu to clear passwords.

 

 

 

 

Recovery (None)

The BIOS recovers data from a recovery diskette

 

 

in the event of a failed BIOS update.

 

 

 

Clearing Passwords

This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode.

1.Observe the precautions in "Before You Begin" on page 27.

2.Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter).

3.Remove the computer cover.

4.Find the configuration jumper block (see Figure 16, B).

5.Place the jumper on pins 2-3 as shown below.

6.Replace the cover, plug in the computer, turn on the computer, and allow it to boot.

7.The computer starts the Setup program. Setup displays the Maintenance menu.

48

Installing and Replacing Desktop Board Components

8.Use the arrow keys to select Clear Passwords. Press <Enter> and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press <Enter>. Setup displays the maintenance menu again.

9.Press <F10> to save the current values and exit Setup.

10.Turn off the computer. Disconnect the computer’s power cord from the AC power source.

11.Remove the computer cover.

12.To restore normal operation, place the jumper on pins 1-2 as shown below.

13.Replace the cover, plug in the computer, and turn on the computer.

Replacing the Battery

A coin-cell battery powers the Desktop Board’s real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied.

When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 17 on page 53 shows the location of the battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.

PRÉCAUTION

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement.

FORHOLDSREGEL

Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning.

OBS!

Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til gjeldende miljølovgivning.

49

Intel Desktop Board D945GSEJT Product Guide

VIKTIGT!

Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljövårdsbestämmelserna.

VARO

Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti.

VORSICHT

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.

AVVERTIMENTO

Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.

PRECAUCIÓN

Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante.

WAARSCHUWING

Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.

ATENÇÃO

Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ

Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.

UPOZORNÌNÍ

V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí.

50

Installing and Replacing Desktop Board Components

Προσοχή

Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς κανονισμούς.

VIGYÁZAT

Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.

AWAS

Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan.

OSTRZEŻENIE

Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.

PRECAUŢIE

Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului.

ВНИМАНИЕ

При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи должны быть утилизированы по возможности. Утилизация батарей должна проводится по правилам, соответствующим местным требованиям.

UPOZORNENIE

Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu.

Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia.

POZOR

Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.

Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi.

51

Intel Desktop Board D945GSEJT Product Guide

.

UYARI

Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

OСТОРОГА

Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.

Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

52

Installing and Replacing Desktop Board Components

To replace the battery, follow these steps:

1.Observe the precautions in "Before You Begin" (see page 27).

2.Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter).

3.Remove the computer cover.

4.Locate the battery on the board (see Figure 17).

5.Disconnect the battery cable from the Desktop Board battery connector (Figure 17, A).

6.Lift up on the battery (Figure 17, B) and carefully remove it from the board. It is attached to the board with a non-permanent adhesive pad.

7.Connect the cable on the new battery to the Desktop Board battery connector and reattach the battery to the board.

8.Replace the computer cover.

Figure 17. Removing the Battery

53

Intel Desktop Board D945GSEJT Product Guide

54

3 Updating the BIOS

The BIOS Setup program can be used to view and change the BIOS settings for the computer. You can access the BIOS Setup program by pressing the <F2> key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins.

This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails.

Updating the BIOS with the Intel® Express

BIOS Update Utility

With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment. The BIOS file is included in an automated update utility that combines the functionality of the Intel® Flash Memory Update Utility and the ease of use of Windows-based installation wizards.

To update the BIOS with the Intel Express BIOS Update utility:

1.Go to http://support.intel.com/support/motherboards/desktop/.

2.Navigate to the Intel Desktop Board D945GSEJT page, click “[view] Latest BIOS updates,” and select the Express BIOS Update utility file.

3.Download the file to your hard drive. (You can also save this file to a removable USB device. This is useful if you are updating the BIOS for multiple identical systems.)

4.Close all other applications. This step is required. Your system will be rebooted at the last Express BIOS Update window.

5.Double-click the executable file from the location on your hard drive where it was saved. This runs the update program.

6.Follow the instructions provided in the dialog boxes to complete the BIOS update.

55

Intel Desktop Board D945GSEJT Product Guide

Updating the BIOS with the Iflash Memory Update Utility

You can use the information in this section to update the BIOS using the Iflash Memory Update Utility.

Obtaining the BIOS Update File

You can update to a new version of the BIOS by using the Iflash BIOS update file.

The Iflash BIOS update file is a compressed file that contains the files you need to update the BIOS. The Iflash BIOS update file contains:

New BIOS file

Intel Flash Memory Update Utility

You can obtain either of these files through your computer supplier or by navigating to the Intel Desktop Board D945GSEJT page at http://support.intel.com/support/motherboards/desktop.

Navigate to the Intel Desktop D945GSEJT page, click “[view] Latest BIOS updates,” and select the Iflash BIOS Update utility file.

CAUTION

Do not interrupt the process or the system may not function properly.

Using the Iflash Memory Update Utility

With the Iflash Memory update utility you can update the system BIOS from a bootable USB flash drive or other bootable USB media. The Iflash BIOS update files can be extracted locally to your hard drive and copied to a bootable USB flash drive or other bootable USB media.

NOTE

Review the instructions distributed with the update utility before attempting a BIOS update.

CAUTION

Do not interrupt the process or the system may not function properly.

1.Uncompress the BIOS update file and copy the .BIO file and IFLASH.EXE to a bootable USB flash drive or other bootable USB media.

2.Configure the BIOS or use the F10 key option during POST to boot to the USB device.

3.Manually run the IFLASH.EXE file from the USB device and manually update the BIOS.

56

Updating the BIOS

Recovering the BIOS

It is unlikely that anything will interrupt a BIOS update; however, if an interruption occurs, the BIOS could be damaged. Table 24 lists the drives and media types that can and cannot be used for BIOS recovery. The BIOS recovery media does not have to be bootable.

Table 24. Acceptable Drives/Media Types for BIOS Recovery

Media Type

Can be used for BIOS recovery?

 

 

CD-ROM drive connected to the PATA interface

Yes

 

 

CD-ROM drive connected to the SATA interface

Yes

 

 

USB removable drive (a USB Flash Drive, for example)

Yes

 

 

USB diskette drive (with a 1.44 MB diskette)

No

 

 

USB hard disk drive

No

 

 

NOTE

For more information about BIOS update and recovery, go to http://support.intel.com/support/motherboards/desktop/sb/CS-022312.htm.

57

Intel Desktop Board D945GSEJT Product Guide

58

A Board Status and Error Messages

This appendix describes status error messages generated by the Desktop Board’s BIOS. The BIOS indicates these error messages with LED blink codes, speaker beep codes, and by text displayed on the PC monitor.

Front-panel Power LED Blink and Internal

Speaker Beep Codes

Basic status and error messages are provided through the front-panel power LED blink codes as well as through audible beep codes on systems with an internal speaker connected to the internal speaker header. Blink/beep codes represent their respective messages as shown in Table 25.

Table 25. Front-panel Power LED Blink and Internal Speaker Beep Codes

Type

Pattern

 

 

CPU Initialization

Beep and blink code: 0.1 second beep/blink within the first second

 

after pressing the power button.

 

 

Completion of POST

Beep and blink code: 0.1 second beep/blink between POST

 

completion and boot device continuing the boot process.

 

 

BIOS update in progress

Beep code: none.

 

Blink code: on-off (0.5 second each); pattern repeats until BIOS

 

update is complete.

 

 

Video error

Beep and blink code: on-off (0.5 second each) two times, then 3.0

 

second pause (off); entire pattern repeats (beeps/blinks and

 

pause) until system is powered off.

 

 

Memory error

Beep and blink code: on-off (0.1 second each) three times, then

 

1.5 second pause (off); entire pattern repeats (beeps/blinks and

 

pause) until system is powered off.

 

 

Thermal warning

Beep and blink code: on-off (0.5 second each) four times, then 3.0

 

second pause (off); entire pattern repeats (beeps/blinks and

 

pause) 16 times, then ends.

 

 

NOTE

BIOS status and error beep codes can be heard through an internal speaker if the internal speaker is connected to the internal mono speaker header (see Figure 1, BB on page 12).

59

Intel Desktop Board D945GSEJT Product Guide

POST Error Messages

The BIOS also displays an error message on the PC monitor when a recoverable error occurs during POST. Table 26 lists the BIOS error messages and a brief description of each.

Table 26. POST Error Messages

Error Message

Explanation

 

 

CMOS Battery Low

The battery may be losing power.

 

 

CMOS Checksum Bad

The CMOS checksum is incorrect. The CMOS memory

 

may have been corrupted. Run Setup to reset values.

 

 

Memory Size Decreased

Memory size has decreased since the last boot. If no

 

memory was removed, then memory may be bad.

 

 

No Boot Device Available

System did not find a device to boot.

 

 

60

B Regulatory Compliance

This appendix contains the following regulatory compliance information for Intel Desktop Board D945GSEJT:

Safety standards

European Union Declaration of Conformity statement

Product Ecology statements

Electromagnetic Compatibility (EMC) regulations

Product certifications

Safety Standards

Intel Desktop Board D945GSEJT complies with the safety standards stated in Table 27 when correctly installed in a compatible host system.

Table 27. Safety Standards

Regulation

Title

 

 

CSA/UL 60950-1, First

Information Technology Equipment – Safety - Part 1: General

Edition

Requirements (USA and Canada)

 

 

EN 60950-1:2006, Second

Information Technology Equipment – Safety - Part 1: General

Edition

Requirements (European Union)

 

 

IEC 60950-1:2005, Second

Information Technology Equipment – Safety - Part 1: General

Edition

Requirements (International)

 

 

Place Battery Marking

There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery. For system safety certification, the statement below or an equivalent statement is required to be permanently and legibly marked on the chassis near the battery.

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.

A suitable caution label is included with Intel Desktop Board D945GSEJT. For information about replacing the battery, go to page 49.

61

Intel Desktop Board D945GSEJT Product Guide

European Union Declaration of Conformity Statement

We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board D945GSEJT is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directives 2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).

The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC and 2006/95/EC.

Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a 2006/95/EC.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 2004/108/EC & 2006/95/EC.

Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004/108/EC & 2006/95/EC.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.

Français Ce produit est conforme aux exigences de la Directive Européenne 2004/108/EC & 2006/95/EC.

Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 2004/108/EC & 2006/95/EC.

Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών

2004/108/EC και 2006/95/EC.

Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv előírásainak.

Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 2004/108/EC & 2006/95/EC.

Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC & 2006/95/EC.

Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC noteikumiem.

Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC nuostatas.

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC u 2006/95/EC.

62

Regulatory Compliance

Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC & 2006/95/EC.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC i 2006/95/EC.

Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC & 2006/95/EC.

Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC & 2006/95/EC.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív 2004/108/EC a 2006/95/EC.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in 2006/95/EC.

Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC & 2006/95/EC.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.

Product Ecology Statements

The following information is provided to address worldwide product ecology concerns and regulations.

Recycling Considerations

As part of its commitment to environmental responsibility, Intel has implemented the Intel® Product Recycling Program to allow retail consumers of Intel’s branded products to return used products to selected locations for proper recycling.

Please consult http://www.intel.com/intel/other/ehs/product_ecology

for the details of this program, including the scope of covered products, available locations, shipping instructions, terms and conditions, etc.

Intel Product Recycling Program

当的重复使用处理。

http://www.intel.com/intel/other/ehs/product_ecology

63

Intel Desktop Board D945GSEJT Product Guide

Deutsch

Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für ordnungsgemäßes Recycling zurückzugeben.

Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte, verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der http://www.intel.com/intel/other/ehs/product_ecology

Español

Como parte de su compromiso de responsabilidad medioambiental, Intel ha implantado el programa de reciclaje de productos Intel, que permite que los consumidores al detalle de los productos Intel devuelvan los productos usados en los lugares seleccionados para su correspondiente reciclado.

Consulte la http://www.intel.com/intel/other/ehs/product_ecology

para ver los detalles del programa, que incluye los productos que abarca, los lugares disponibles, instrucciones de envío, términos y condiciones, etc.

Français

Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis en œuvre le programme Intel Product Recycling Program (Programme de recyclage des produits Intel) pour permettre aux consommateurs de produits Intel de recycler les produits usés en les retournant à des adresses spécifiées.

Visitez la page Web http://www.intel.com/intel/other/ehs/product_ecology pour en savoir plus sur ce programme, à savoir les produits concernés, les adresses disponibles, les instructions d'expédition, les conditions générales, etc.

http://www.intel.com/in tel/other/ehs/product_ecology

Malay

Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran, Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.

Sila rujuk http://www.intel.com/intel/other/ehs/product_ecology untuk mendapatkan butir-butir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia, arahan penghantaran, terma & syarat, dsb.

64

Regulatory Compliance

Portuguese

Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o Programa de Reciclagem de Produtos para que os consumidores finais possam enviar produtos Intel usados para locais selecionados, onde esses produtos são reciclados de maneira adequada.

Consulte o site http://www.intel.com/intel/other/ehs/product_ecology (em Inglês) para obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os locais disponíveis, as instruções de envio, os termos e condições, etc.

Russian

В качестве части своих обязательств к окружающей среде, в Intel создана программа утилизации продукции Intel (Product Recycling Program) для предоставления конечным пользователям марок продукции Intel возможности возврата используемой продукции в специализированные пункты для должной утилизации.

Пожалуйста, обратитесь на веб-сайт http://www.intel.com/intel/other/ehs/product_ecology за информацией об этой программе, принимаемых продуктах, местах приема, инструкциях об отправке, положениях и условиях и т.д.

Türkçe

Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya koymuştur.

Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen http://www.intel.com/intel/other/ehs/product_ecology web sayfasına gidin.

65

Intel Desktop Board D945GSEJT Product Guide

Lead-free 2LI/Pb-free 2LI Board

The electronics industry is transitioning to European Union (EU) Restriction of Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the use of six materials. One of these restricted materials is lead. Lead is the most common and problematic of the RoHS restricted materials.

There are exemptions in RoHS that allow the use of lead in some very limited locations in electronic products. Maximum lead concentration values have been established for RoHS-compliant electronic products that allow up to 1000 ppm of lead.

Lead-free/Pb-free is a nickname that is often used (or misused) for RoHS-compliant products. In this case, the term "Lead-free/Pb-free" means that lead has been removed where required by the RoHS legislation but still may exist as an impurity below 1000 ppm.

The term "Lead-free 2LI/Pb-free 2LI" means lead-free second level interconnect (2LI). The balls, leads, or pads used to connect the component to a printed circuit board are lead-free, but the first level interconnect (FLI) is not lead-free. The use of lead in the FLI is acceptable because of the RoHS "flip chip" or "die bump" interconnect exemption.

Intel Desktop Board D945GSEJT is a lead-free second level interconnect product. Table 28 shows the lead-free second level interconnect marks as they appear on the board and accompanying collateral. These marks are based on JEDEC standard J-STD-609, “Marking and Labeling of Components, PCBs and PCBAs to Identify Lead, Lead Free and Other Attributes.”

For more information concerning Intel’s lead-free initiatives, refer to http://www.intel.com/technology/silicon/leadfree.htm.

Table 28. Lead-Free Second Level Interconnect Marks

Description

Mark

 

 

 

 

 

 

 

 

 

This symbol is used to identify

 

 

 

 

 

 

 

 

 

 

 

 

 

 

electrical and electronic

 

 

 

 

 

 

 

assemblies and components in

 

 

 

 

 

 

 

which the Pb concentration

 

 

 

 

 

 

 

level in the Desktop Board

 

 

 

 

 

 

 

substrate and the solder

 

 

 

 

 

 

 

 

 

 

or

 

connections from the board to

 

 

 

 

the components (second-level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

interconnect) is not greater

 

 

 

 

 

 

 

than 0.1% by weight

 

 

 

 

 

 

 

(1000 ppm).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

66

Regulatory Compliance

Restriction of Hazardous Substances (RoHS)

European Union RoHS

EU RoHS Directive 2002/95/EC restricts the use of the following six materials in various types of electronic and electrical equipment:

Lead

Mercury

Cadmium

Hexavalent chromium

Polybrominated biphenyls (PBB)

Polybrominated diphenyl ether (PBDE)

The maximum concentrations allowed are 0.1% or 1000 ppm (except for cadmium, which is limited to 0.01% or 100 ppm) by weight of homogeneous material.

Intel Desktop Board D945GSEJT complies with these restrictions.

China RoHS

“China RoHS” is the term used by industry generally to describe legislation implemented by the Ministry of Information Industry (MII) in the People's Republic of China for the control of pollution by electronic information products (EIP). The official title of the China RoHS regulation is “Management Methods for Controlling Pollution by Electronic Information Products.”

China RoHS bans the same substances and has the same limits as EU RoHS. However, the China RoHS regulation requires specific product marking and a selfdeclaration of the controlled substances contained in each product.

Intel Desktop Board D945GSEJT is a China RoHS-compliant product.

The required China RoHS mark indicates the product’s Environmental Friendly Usage Period (EFUP). The EFUP is defined as the number of years for which listed controlled substances will not leak or chemically deteriorate while in the product. The EFUP for Intel Desktop Boards has been determined to be 10 years.

The EFUP for Intel Desktop Board D945GSEJT is shown in Table 29.

Table 29. China RoHS Environmentally Friendly Use Period Mark

Description

Mark

This is an example of the symbol used on Intel Desktop Boards and associated collateral. The color of the mark may vary depending upon the application. The Environmental Friendly Usage Period (EFUP) for Intel Desktop Boards has been determined to be 10 years.

67

Intel Desktop Board D945GSEJT Product Guide

The China MII also stipulates that a material Self Declaration Table (SDT) must be included in a product’s user documentation. The SDT for Intel Desktop Board D945GSEJT is shown in Figure 18.

Figure 18. Intel Desktop Board D945GSEJT China RoHS Material

Self Declaration Table

68

Regulatory Compliance

EMC Regulations

Intel Desktop Board D945GSEJT complies with the EMC regulations stated in Table 30 when correctly installed in a compatible host system.

Table 30. EMC Regulations

Regulation (Class B)

Title

 

 

FCC 47 CFR Part 15,

Title 47 of the Code of Federal Regulations, Part 15, Subpart B,

Subpart B

Radio Frequency Devices. (USA)

 

 

ICES-003 Issue 4

Interference-Causing Equipment Standard, Digital Apparatus.

 

(Canada)

 

 

EN55022:2006

Limits and methods of measurement of Radio Interference

 

Characteristics of Information Technology Equipment. (European

 

Union)

 

 

EN55024:1998

Information Technology Equipment – Immunity Characteristics

 

Limits and methods of measurement. (European Union)

 

 

EN55022:2006

Australian Communications Authority, Standard for

 

Electromagnetic Compatibility. (Australia and New Zealand)

 

 

CISPR 22:2005

Limits and methods of measurement of Radio Disturbance

+A1:2005 +A2:2006

Characteristics of Information Technology Equipment.

 

(International)

 

 

CISPR 24:1997

Information Technology Equipment – Immunity Characteristics –

+A1:2001 +A2:2002

Limits and Methods of Measurement. (International)

 

 

VCCI V-3/2007.04,

Voluntary Control for Interference by Information Technology

V-4/2007.04

Equipment (Japan)

 

 

KN-22, KN-24

Korean Communications Commission – Framework Act on

 

Telecommunications and Radio Waves Act. (South Korea).

 

 

CNS 13438:2006

Bureau of Standards, Metrology and Inspection. (Taiwan)

 

 

Japanese Kanji statement translation: This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

69

Intel Desktop Board D945GSEJT Product Guide

Korean Class B statement translation: This is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non-residential environments.

Ensure Electromagnetic Compatibility (EMC) Compliance

Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly.

Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules:

Product certifications or lack of certifications

External I/O cable shielding and filtering

Mounting, grounding, and bonding requirements

Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing may be required on a representative sample of the newly completed computer.

70

Regulatory Compliance

Product Certifications

Board-Level Certification Markings

Intel Desktop Board D945GSEJT has the product certification markings shown in Table 31.

Table 31. Product Certification Markings

Description

Mark

UL joint US/Canada Recognized Component mark. Includes adjacent

 

UL file number for Intel Desktop Boards: E210882.

 

 

 

FCC Declaration of Conformity logo mark for Class B equipment.

 

Includes Intel name and D945GSEJT model designation.

 

 

 

CE mark. Declaring compliance to European Union (EU) EMC

 

directive and Low Voltage directive.

 

 

 

Australian Communications Authority (ACA) and New Zealand Radio

 

Spectrum Management (NZ RSM) C-tick mark. Includes adjacent

 

Intel supplier code number, N-232.

 

 

 

Japan VCCI (Voluntary Control Council for Interference) mark.

 

 

 

S. Korea KCC (Korean Communications Commission) mark. Includes

 

adjacent KCC certification number: CPU-D945GSEJT (B).

 

 

 

Taiwan BSMI (Bureau of Standards, Metrology and Inspections)

 

mark. Includes adjacent Intel company number, D33025.

 

 

 

Printed wiring board manufacturer’s recognition mark. Consists of a

V-0

unique UL recognized manufacturer’s logo, along with a flammability

 

rating (solder side).

 

71

Intel Desktop Board D945GSEJT Product Guide

Chassis and Component Certifications

Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical product certifications include:

In Europe

The CE marking signifies compliance with all applicable European requirements. If the chassis and other components are not properly CE marked, a supplier’s Declaration of Conformity statement to the European EMC directive and Low Voltage directive (as applicable), should be obtained. Additionally, other directives, such as the Radio and Telecommunications Terminal Equipment (R&TTE) directive may also apply depending on product features.

In the United States

A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL, CSA, or ETL signifies compliance with safety requirements. Wiring and cables must also be UL listed or recognized and suitable for the intended use. The FCC Class B logo for home or office use signifies compliance with electromagnetic interference (EMI) requirements.

In Canada

A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements. The Industry Canada statement at the front of this product guide demonstrates compliance with Canadian EMC regulations.

72