Infinity TSS 3-IN-1 User Manual

Technical Manual

TSS 3-IN-1

ACOUSTIC & ELECTRICAL SPECIFICATIONS:

• Nominal Impedance 8 Ohms

• Max Amp Power 125 Watts*

• Frequency Response 120Hz – 20kHz (±3dB)

• Sensitivity 89dB (2.83V @ 1 meter)

• Crossover Frequency 3,500Hz; 24dB/Octave

SYSTEM COMPONENTS:

• Grille NT-80317-02 (Platinum) NT-80317-01 (Charcoal)

• Low-Frequency Transducer 3-1/2" (89mm) MMD

, magnetically shielded (080F30004)

DC Resistance 7.8 Ohms, ±10%

• High-Frequency Transducer 3/4" (19mm) MMD, magnetically shielded (020D30901)

DC Resistance 3.2 Ohms, ±10%

• Crossover Network FL-80305-01MS (Platinum) FL-80305-01MBS (Charcoal)

PACKAGING

AURAL SWEEP TEST SPECIFICATIONS:

• System Aural Sweep Test 6.0V Input 120Hz to 20kHz

• L.F. Aural Sweep Test 5.0V Input 120Hz to 4kHz

• H.F. Aural Sweep Test 2.83V Input 3kHz to 20kHz

PHYSICAL SPECIFICATIONS:

• Dimensions 4-1/8" x 40-1/8" x 4-3/8" (H x W x D) (105mm x 1019mm x 111mm)

• Weight 15.25 lb (6.9kg) Each

WARRANTY:

• Refer to Warranty Statement packed with each product.

* The maximum recommended amplifier power rating will ensure

proper system headroom to allow for occasional peaks. We do not recommend sustained operation at these maximum power levels.

TSS 3-IN-1 WIRING DIAGRAM (x3)

27 28

Legend on Page 2

CROSSOVER

NETWORK

FL-80305-01MS (Platinum)

FL-80305-01MBS (Charcoal)

TSS 3-IN-1 SCHEMATIC (x3)

0.4mH

1.8 ohm 10w

5.1μf 100v

HIGH-FREQUENCY

TRANSDUCER

020D30901

16μf

100v

0.18mH

LOW-FREQUENCY

TRANSDUCERS (2)

080F30004

140mm

120mm

.205

.110

.205

.110

Infinity Systems, 250 Crossways Park Drive, Woodbury, New York 11797

TSS 3-IN-1

3/07

Technical Manual

TSS 3-IN-1

EXPLODED VIEW

ITEM NO. DESCRIPTION QTY. PART NO.

1. Aluminum cabinet 1 Not For Sale

2. Plastic front baffle (Platinum) 1 FA-80317-02 Plastic front baffle (Charcoal) 1 FA-80317-01

3. Top/bottom cap (Platinum) 1 FE-80312-02 Top/bottom cap (Charcoal) 1 FE-80312-03

4. Plastic inner cover 1 Not For Sale

5. Wall-mount end caps, small (Platinum) 2 BP1-80312-02 Wall-mount end caps, small (Charcoal) 2 BP1-80312-04

6. Wall-mount end caps, large (Platinum) 2 BP2-80312-03 Wall-mount end caps, large (Charcoal) 2 BP2-80312-05

7. Front grille (Platinum) 1 NT-80317-02 Front grille (Charcoal) 1 NT-80317-01

8. Front grille gasket 2 PK-0106-01

9. Crossover network (Platinum) 3 FL-80305-01MS Crossover network (Charcoal) 3 FL-80305-01MBS

10. Speaker base (Platinum) 1 SP-80317-02 Speaker base (Charcoal) 1 SP-80317-01

11. Speaker-base gasket (Platinum) 1 PK-0107-02

Speaker-base gasket (Charcoal) 1 PK-0107-01

12. Wall-bracket cover (Platinum) 1 SP-80317-03 Wall-bracket cover (Charcoal) 1 SP-80317-01

13. Main wall bracket (Platinum) 1 SP-80317-04 Main wall bracket (Charcoal) 1 SP-80317-02

14. Screw, woofer M4*7 24 SR-2104-07

15. Screw, terminals M3.5*12 (Platinum) 12 SR-2435-12 Screw, terminals M3.5*12 (Charcoal) 12 SR-2435-12B

16. Screw, tweeter M3.5*10 6 SR-0535-10

17. Screw, wall bracket M4*18 (Platinum) 4 SR-0304-18 Screw, wall bracket M4*18 (Charcoal) 4 SR-0304-18A

18. Screw, top cap M6*18 (Platinum) 2 SR-1006-18 Screw, top cap M6*18 (Charcoal) 2 SR-1006-18A

19. 3.5" Woofer 6 080F30004

20. 3/4" Tweeter 3 020D30901

21. Hex wrench 1 HW-4001-01

22. Gasket, front baffle 3 PK-80311-02

23. Gasket, network 3 PK-80307-01

24. Gasket, wall bracket (Platinum) 4 PK-1019-01 Gasket, wall bracket (Charcoal) 4 PK-1019-02

25. Logo 1 AL-80305-01

26. Outer carton (Platinum) 1 BO-80317-01 Outer carton (Charcoal) 1 BO-80317-03

27. Packing polyfoam, set complete 1 PO-80317-01/2/3

28. Owner’s manual 1 ML-80317-01

29. Warranty card 1 WC-TSS4000-01

TO SERVICE THE TSS 3-IN-1

1. Remove both end caps with a 4mm or 5-32" Allen wrench (hex key).

2. Gently pull up the metal grille from one end, and remove grille.

3. Remove the plastic front baffle by using a small screwdriver on one corner of the front baffle and lifting the baffle corner away from the cabinet (see illustration).

4. Once one corner is lifted away, reach under the front baffle to pull and extract both sides of the front baffle from the cabinet, on that end. This is complicated by the fact that three tweeters, bolted to the front baffle, are also attached with adhesive, so each bead must be carefully broken.

5. CAUTION: Once the baffle starts to separate from the cabinet, do not lift the baffle too high off the cabinet and attempt to remove it; the tweeter wires – three sets – are attached. The tweeter wire clips must be detached from the tweeters as the baffle is removed.

6. Once the front baffle is removed, all drivers are exposed for servicing. The crossover network(s) is attached to the inside of the cabinet, and woofers may need to be removed to replace the network(s).

7. Upon reassembly, there should still be enough adhesive left on the baffle to reattach it to the cabinet face; if not, apply a light coating of contact cement, silicone seal, or similar adhesive to the surfaces around the tweeters.

TSS 3-IN-1

Infinity Systems, 250 Crossways Park Drive, Woodbury, New York 11797

3/07