TSS-Sub500
(TSS-500 SYSTEM)
SERVICE MANUAL
Infinity Systems Incorporated
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 6/2006
1
TSS-Sub500
Note: The TSS-Sub500 is part of the TSS-500 system
Satellite loudspeakers:
(Charcoal) order Infinity part# TSS-SAT500CHR
(Platinum) order Infinity part# TSS-SAT500PLT
Center channel: Call Infinity Systems parts department
(Charcoal) (Platinum)
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . ………………….………….... .. . . . . . 1
PACKAGING/ACCESSORIES. . . . . . . . . . . . . . . . . .………. . .. .. ... . . . . . 2
DETAILED SPECIFIC ATIONS . . . . . . . . . . . . . . . . . .………. . .. .. .. . . . . . 3
CONTROLS. ………………….. .. . …………………………………………….. 5
CONNECTIONS . . . . . . . . . . . ……….………………………………..…. . . . 6
OPERATION……. . . . . .. . . . . . . . .. .. . . . .. .. . . . . ….……… . . ... . . . . . . .7
EXPLODED VIEW-MECHANICAL PARTS LIST….… . ………………………..8
TEST SET-UP/PROCEDURE. . . . . . . . . . . . . . . . . .………. . .. .. .…. . . . . . 9
BLOCK DIAGRAM. . . . ………………... ………………………….... . . .. . … . 10
TROUBL E SHO O TI NG FL O W CH A R T ….… . ………………….………………11
PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ……………………………….. …12
ELECTRICAL PARTS LIST …………. .... . .. . . . . . ……………………... . . . 20
IC – TRANSISTOR PINOUTS . … . . .. . . . . . ………………………….... . . . 24
SCHEMATIC DIAGRAMS . . …………………………………….……………. . .25
TSS-Sub500 Specifications
Frequency Range: 39Hz – 150Hz (±3dB)
Amplifier Output: 100 watts RMS
Low-Frequency Driver: 8" (203mm)
Crossover Frequency: 120Hz, 24dB/Octave (line-level [non-LFE] input)
Dimensions (H x W x D): 15-7/8" x 13-5/8" x 14-5/8"
(403mm x 346mm x 3 71mm)
Weight: 31.7 lb (14.4kg)
Infinity c ontinually strives to update and improve existing pr oduc ts, as well as create new ones. The specificat ions
and construction details i n this and relat ed Infinity publications are therefore subject to c hange without noti c e.
2
TSS-Sub500
TSS-500 PACKING/ACCESSORIES
Item # Description Part Number Qty
1 Warranty Card 405-000-05110-E 1
2 Owner’s Manual 406-000-05307-E 1
3 Packing Not for Sale 1
4 Packing Bag Not for Sale 4
5 Inner Carton Not for Sale 1
6 Packing Bag Not for Sale 1
7 Nut wrench (metal bar) 399-FE-00630-E 1
8 15’ RCA cable 370-000-00273-E 1
9 Rubber feet for stands (Platinum) 373-000-05051-E 1
Rubber feet for stands (Charcoal) 373-000-05050-E 1
10 Screw for stands (5) ¼ x 20 x1” (Platinum) 371-000-05108-E 1
Screw for stands (5) ¼ x 20 x1” (Charcoal) 371-000-05114-E 1
11 Wall Bracket ball end (5) (Platinum) 373-000-05054-E 1
Wall Bracket ball end (5) (Charcoal) 373-000-05055-E 1
12 40’ Wire set (2) 370-000-00276G-E 2
13 20’ Wire set (3) 370-000-00277G-E 3
14 Satellite stand (Platinum) 325-ABS-05126-0VAE 4
Satellite stand (Charcoal) 325-ABS-05127-0BAE 4
15 Wall bracket 398-ABS-00317-0VAE 5
16 Center table stand (Platinum) 325-ABS-05127-0VAE 1
Center table stand (Charcoal) 325-ABS-05126-0BAE 1
17 Rubber gasket for stand 336-RUB-05200-0VAE 1
18 Subwoofer Top Packing 431-000-05639-E 1
19 Packing Bag Not for Sale 1
20 Subwoofer Btm Packing 431-000-05640-E 1
21 Desiccant Not for Sale 3
22 Outer Carton (Platinum) 402-000-05533-E 1
Outer Carton (Charcoal) 402-000-05534-E 1
Y
y
3
TSS-Sub500
TSS-Sub500 100W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120VAC/60Hz Yes 108-132 Vrms
Europe 220-240VAC, 50-60Hz Yes 220-240 Vrms
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) AB AB
Type (Class AB, D, other) G G
Load Impedance (speaker) 4 Ohms
Rated Output Power 100 Watts
THD@ Rated Power 0.5 %
THD @ 1 Watt 0.1 %
DC Offset 10 mV-DC
Damping factor >100 DF
Input Sensitivity
Input Frequency 50 Hz
Line Input (L&R) 13.8 mVrms
LFE Input 8.62 mVrms
Signal to Noise
SNR-A-Weighted 100 dBA
SNR-unweighted 80 dBr
SNR @ 1W-unweighted 60 dBr
Residual Noise Floor 1 mVrms
Residual Noise Floor 1
Input Impedance
Line input L&R , LFE >10 K ohms
es/No Hi/Lo Line Unit Notes
n/a 120V Model External Sink required
n/a 230V Model External Sink required
n/a Nominal
95 Single input driven
0.5 22K filter
50 @ Speaker Output
100 50Hz, 4 Ohms load
50 Nominal Freq.
±2dB To 1 Watt Single input driven, AP Zo=600 Ohms
±2dB To 1 Watt LFE input driven only, AP Zo=600 Ohms
85 rel. to rated power A-Weighting filter
80 rel. to rated power 22K filter
60 rel. to 1W Output 22K filter
mVrms(max)
n/a Nominal
Normal Operation
Normal Operation
1 22K filter
Volume @max, using RMS reading
2
DMM/VOM (or A/P)
Volume @max, w/ A/P Swept Bandpass
2
Measurement (Line freq.+ harmonics)
Measured at amplifier board speaker output
terminals, Output power 90 Watts
Filters
Low Pass (fixed or variable) 4th order fix -Subsonic filter (HPF) 2nd order Hz
Limiter (yes/no) YES -THD at Max. Output Power 1 %
Features
LFE Input YES
Volume pot Taper (lin/log) LOG -ATO YES
Input Configuration
Line In (L,R) L ,R -Line level in LFE LFE
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES -ATO Input Frequency 50 Hz
ATO Level 2 mV
ATO Turn-on time 5 ms
Auto Mute/ Turn-OFF Time 10 minutes
Power on Delay time 3 sec.
Transients/Pops
ATO Transient 5 mV-peak
Turn-on Transient 50 mV-peak
Turn-off Transient 50 mV-peak
±2dB
±2dB
Functional
Functional
Functional
Functional
Functional
Functional RCA inputs
Functional
Functional
Functional
Functional
Functional
Functional T before muting, after signal is removed Auto turn of time (T) must be 5 > T <15
Functional AC Power Applied
10 Speaker Outputs
100 Speaker Output AC Line cycled from OFF to ON
100 Speaker Output AC Line cycled from ON to OFF
2mV@50Hz into Line Input w/ 1 ch.
driven
Amp connected and AC on, then input
signal applied
Efficienc
Stand-by Input Power 12 Watts
Power Cons.@rated power 195 Watts
15 @ nom. line voltage
210 @ nom. line voltage
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
100 Watts @ 4 Ohms nominal line voltage
4
TSS-Sub500
Parameter Specification Unit QA Test Limits Conditions Notes
Protection
Short Circuit Protection YES --
Thermal Protection 65 deg. C -DC Offset Protection YES --
Line Fuse Rating
120 VAC 2.5 Amps
230 VAC 1.25 Amps
Functional Direct short at output
Functional @1/8 max unclipped Power
Functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
Type-T or Slo Blo, Fuse Markings T2.5A,
250V
Type-T, Low breaking capacity, Fuse
markings T1.25AL, 250V
Temperature rise should not exceed 35K
rise
External fuse with UL/SEMKO rated holder
This area is designed to become quite warm
during normal operation.
This area is designed to become quite warm
during normal operation.
This area is designed to become quite warm
during normal operation.
NRTL/C
C
SA22-2 NO.1
U
L1492
R
TSS-Sub500
¡
™
£
¢
5
TSS-Sub500
SUBWOOFER CONTROLS
Rear Panel
A Few Suggestions
We recommend that you do not operate your speakers or
subwoofer with the bass,treble and loudness controls set to
full boost.This will place undue strain on your electronics and
speakers and could damage them.
The volume control setting on your processor/preamp or receiver
is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
which the system can be played, regardless of where the volume
control is set.
Always turn down the volume control setting on your processor/
preamp or receiver when changing a cassette or CD,or switching
inputs to AM or FM operation. Excessively loud transients (clicks or
popping sounds) can damage the satellite speakers and possibly
the subwoofer.
¡
Subwoofer Level Control
™
LFE Input
£
Line-Level Inputs
¢
Power Switch
Important!
Whenever changing cables, pulling plugs, etc.,ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
5
TSS-500
SUBWOOFER OR
L
FE OUTPUT
R
ECEIVER/PROCESSOR
6
TSS-Sub500
SUBWOOFER CONNECTIONS
If you have a Dolby
processor with a low-frequency-effects (LFE)
or subwoofer output:
15' (4.6m) subwoofer
cable included
®
Digital or DTS®receiver/
If your receiver/processor does not contain
a Dolby Digital or DTS processor but has a
subwoofer output:
15' (4.6m) subwoofer
cable included
NOTE: If your receiver/processor has only one sub out,
you may use either the L or R input.
TSS-500
6
7
TSS-Sub500
OPERATION
Surround Modes
When using the TSS-500 in a Dolby Digital or DTS home theater
system, make sure all speakers are set to “Small”. When using the
system in a Dolby Pro Logic
receiver’s center channel mode is set to “Normal.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode (e.g., CD-stereo,
videotape,Dolby Digital, Pro Logic).In each case, follow your
equipment’s instructions to ensure that the subwoofer output is
turned on and that the speakers are set to “Small”in each mode.
If your receiver has adjustable crossover settings,we recommend
the subwoofer crossover be set between 100Hz and 120Hz.
Power On
Plug your subwoofer’s AC cord into a wall outlet.Do not use the
outlets on the back of the receiver.
Initially set the Subwoofer Level Control
Turn on the subwoofer by pressing the Power Switch
rear panel.
Turn on your entire audio system and start a CD or movie
soundtrack at a moderate level.
Auto On/Standby
With the Power Switch 4in the ON position, the LED on the back
will remain lit in green or red to indicate the ON/STANDBY mode of
the subwoofer.
RED = STANDBY (No signal detected,Amp Off)
GREEN = ON (Signal detected,Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a signal
is detected. During periods of normal use,the Power Switch
can be left on.You may turn off the Power Switch 4for extended
periods of nonoperation,e.g., when you are away on vacation.
®
home theater system, make sure the
1
to the“MIN”position.
4
on the
4
enhance bass, extending the response of the entire system so
the bass can be felt as well as heard.However,overall balance
must be maintained or the music will not sound natural.An
experienced listener will set the volume of the subwoofer so its
impact on bass response is always there but never obtrusive.
Final Positioning
After correctly connecting the TSS-500 system and verifying
that both the subwoofer and all satellite speakers are playing,
it is time to optimize the system for your particular listening
room. Earlier,you placed the subwoofer in its general location.
Finding the exact location for optimum performance sometimes
only involves moving the speakers up to a few inches in any
direction.We urge you, therefore, to experiment with placement,
if possible, until your speakers deliver their full potential.
MAINTENANCE AND SERVICE
The satellite and subwoofer enclosures may be cleaned using a
soft cloth to remove fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions
and other factors,but once per year is the minimum.
If a problem occurs,make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker,reverse
the connection wires to the left and right system.If the problem
remains in the same speaker,then the fault is with the loudspeaker. If the problem appears in the opposite speaker, the
cause is in another component or cable. In the event that your
TSS-500 ever needs service, contact your local Infinity dealer or
visit www.infinitysystems.com for a service center near you.
Adjust Level
Turn the Subwoofer Level Control 1up about halfway.If no sound
emanates from the subwoofer, check the AC-line cord and input
cables.Are the connectors on the cables making proper contact?
Is the AC plug connected to a “live”receptacle? Has the Power
4
Switch
confirmed that the subwoofer is active, proceed by playing a CD
or DVD. Use a selection that has ample bass information.
Set the overall volume control of the receiver/processor to a
comfortable level.Adjust the Subwoofer Level Control
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce
lots of bass.This is not entirely true.A subwoofer is there to
7
TSS-500
been pressed to the “On”position? Once you have
1
until
8
TSS-Sub500
9
TSS-Sub500
Test Set Up and Procedure
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not
the single LFE input.
2) On the front of the unit, turn the LEVEL control full counterclockwise.
3) Turn on generator, adjust to 100mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.
6) Turn off generator, turn LEVEL control fully counterclockwise, disconnect RCA cable.
Sweep Function
1) Follow steps 3-6 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.3 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
connect to
10
TSS-Sub500
11
TSS-Sub500
TSS500
Troubleshooting Flow Chart
no
yes
yes
yes no
yes
yes
no
AMP no signal out
Check fuse, transformer,
DC voltage check ±Vcc
Check +/-15v
LED red
Led light blue or red
LED light blue yes yes
Check U202 pin14 signal
yes yes no
no
Check limiter board C304
Check Q117,118,119,D109 etc
Check U201
pin14 signal
D110,D115 etc
Check,Q203,207,U203 etc
Check U201,R226,223 ,
U202,R213,214,C206
etc
Check U301,R343,344 ,
C340,Q301,302, etc
yes
yes yes
no
Test R121,122 signal
no
yes yes
Check RLY101,D102,Q113,114
yes
no
Check U101,Q115,116,R138
yes
yes
Check P102 signal
Check ,+vsw& -vsw
DC voltage
Check Q107,108,105,
Q106,103,104,U101,etc
Change the component
The Amp ass’y ok, END
Check Q120,121,122,123
Q124,125,126,127 etc
12
TSS-Sub500
13
TSS-Sub500
14
TSS-Sub500
15
TSS-Sub500
16
TSS-Sub500
17
TSS-Sub500
18
TSS-Sub500
19
TSS-Sub500
y
20
TSS-Sub500
TSS-Sub500 (120v) Electrical Parts List
Part Number
Description
Qt
PREAMP PCB
Resistors
110-16102j26 Resistor 1K 1/6W ±5% CF 26mm 4
110-16103j26 Resistor 10K 1/6W ±5% CF 26mm 13
110-16104j26 Resistor 100K 1/6W ±5% CF 26mm 2
110-16105j26 Resistor 1M 1/6W ±5% CF 26mm 1
110-16122j26 Resistor 1.2K 1/6W ±5% CF 26mm 1
110-16124j26 Resistor 120K 1/6W ±5% CF 26mm 1
110-16151j26 Resistor 150Ω 1/6W ±5% CF 26mm 1
110-16153j26 Resistor 15K 1/6W ±5% CF 26mm 1
110-16154j26 Resistor 150K 1/6W ±5% CF 26mm 1
110-16183j26 Resistor 18K 1/6W ±5% CF 26mm 2
110-16205j26 Resistor 2M 1/6W ±5% CF 26mm 1
110-16223j26 Resistor 22K 1/6W ±5% CF 26mm 4
110-16273j26 Resistor 27K 1/6W ±5% CF 26mm 2
110-16333j26 Resistor 33K 1/6W ±5% CF 26mm 1
110-16472j26 Resistor 4.7K 1/6W ±5% CF 26mm 2
110-16473j26 Resistor 47K 1/6W ±5% CF 26mm 2
110-16512j26 Resistor 5.1K 1/6W ±5% CF 26mm 3
110-16513j26 Resistor 51K 1/6W ±5% CF 26mm 1
115-h503a104 variable Resistor D16 50K/1 A LEVEL 1
Reference Designator
R213,214,215,254
R212,216,217,220,221,222,225,228,226,232,
235,240,248
R231,266
R259
R264
R233
R253
R234
R252
R262,227
R257
R238,247,250,255
R223,237
R249
R258,260
R219,251
R211,229 ,230
R224
VR201
Capacitors
130-2b221k503 disc Capacitor 220P 50V ± 10% 9
130-3f104z503 disc Capacitor 0.1U 50V +80/-20% 7
130-sl470k503 disc Capacitor 47P 50V ± 10% 1
132-103j503 electrolytic 0.01U 50V ± 5% 2
132-104j503 electrolytic 0.1U 50V ± 5% 3
132-223ja03 electrolytic 0.22uF 100V ± 5% 1
132-473j503 electrolytic 0.047U 50V ± 5% 2
135-3105m50 electrolytic 1U 50V ± 20% 1
135-3106m50 electrolytic 10uF 50V ± 20% 8
135-3107m16 electrolytic 100uF 16V ± 20% 2
135-3226m50 electrolytic 22U 50V ± 20% 1
Semiconductors
192-027c1815gr Transistor 2SC1815GR NPN 3
197-031n4148 diode 100mA 75V SIGNAL 1N4148 ROHM 7
199-15000335 zener diode 3.3V 1/2W 52mm 1
190-06m4558d I.C OPA 4558D DUAL OP-AMP 1
190-16t1074cn I .C TL074cm QUAD OP-AMP 2
195-10204hgw LED 204HGW 3c 1
Miscellaneous
162-50159201 WIRE ASS'Y 2PIN 150mm 1
174-0rca326p JACK RCA-326 1
C207,208,210,211,212,214,220,230,249
C232,242,244,245,246,252,254
C229
C223,224
C218,221,222
C215
C216,217
C228
C206,213,219,231,241,243,251,253
C233,234
C225
Q201,206,207
D201,202,207,208,211,212,214
D213
U203
U201,202
D209
for D209
JK202
POWER/MAIN PCB
Resistors
110-14472j26 Resistor 4.7K 1/4W ±5% 26mm 2
110-14681j26 Resistor 680Ω 1/4W ±5% 26mm 2
R147,150
R148,151
y
21
TSS-Sub500
Part Number
Description
POWER/MAIN PCB
Reference Designator
Qt
110-16101j26 Resistor10 0Ω 1/6W ±5%CF 26mm 1
110-16102j26 Resistor 1K 1/6W ±5% CF 26mm 1
110-16103j26 Resistor 10K 1/6W ±5% CF 26mm 1
110-16105j26 Resistor 1M 1/6W ±5% CF 26mm 1
110-16123j26 Resistor 12K 1/6W ±5% CF 26mm 2
110-16152j26 Resistor 1.5K 1/6W ±5% CF 26mm CF 6
110-16153j26 Resistor 15K 1/6W ±5% CF 26mm 4
110-16154j26 Resistor 150K 1/6W ±5% CF 26mm 1
110-16181j26 Resistor 18Ω 1/6W ±5% CF 26mm 2
110-16182j26 Resistor 1.8K 1/6W ±5% CF 26mm 1
110-16223j26 Resistor 22K 1/6W ±5% CF 26mm 3
110-16332j26 Resistor 3.3K 1/6W ±5% CF 26mm 3
110-16392j26 Resistor 3.9K 1/6W ±5% CF 26mm 2
110-16393j26 Resistor 39K 1/6W ±5% CF 26mm 1
110-16470j26 Resistor 47Ω 1/6W ±5%CF 26mm 4
110-16471j26 Resistor 470Ω 1/6W ±5% CF 26mm 1
110-16472j26 Resistor 4.7K 1/6W ±5% CF 26mm 3
110-16473j26 Resistor 47K 1/6W ±5% CF 26mm 1
110-16560j26 Resistor 56Ω 1/6W ±5% CF 26mm 1
110-16563j26 Resistor 56K 1/6W ±5% CF 26mm 1
110-16682j26 Resistor 6.8K 1/6W ±5% CF 26mm 1
110-10821jk2 Resistor 820Ω 1W ±5% 10mm 1
110-122r2j15 Resistor 2.2Ω 1/2W ±5% 15mm 1
110-20331jk2 Resistor 330Ω 2W ±5% 5mm 2
113-50r10j10 cement Resistor 0.1Ω 5W ±5% 2
114-03302m0 semi-fixed Resistor 3K 0.3W 1±20% 1
R120
R124
R134
R143
R135,139
R103,123,136,137,141,142
R118,145,152,154
R131
R111,114
R153
R128,129,133
R106,107,144
R105,108
R126
R112,113,115,116
R140
R110,125,130
R101
R117
R104
R109
R132
R127
R146,149
R121,122
R138
Capacitors
130-2b102k503 disc Capacitor 1000p 50V±10% 1
130-2f104z503 disc Capacitor0.1u 50V+80/ -20% 4
130-3f473m503 disc Capacitor0.047u 50V±20% 1
130-s1101k503 disc Capacitor100p 50V SL±10% 2
132-104j503 mylar Capacitor 0.1u50V ±5% 1
132-223ja03 mylar Capacitor 0.022uF 100V ±5% 4
135-3105m50 mylar Capacitor 1U 50V ±20% 2
135-3107m16 mylar Capacitor100uF 16V ±20% 3
135-3226m50 mylar Capacitor22U 50V ±20% 2
135-3227m10 mylar Capacitor220U 10V ±20% 2
135-3227m16 mylar Capacitor220U 16V ±20% 1
135-3476m25 mylar Capacitor47U 25V ±20% 1
132-223ja03 mylar Capacitor 0.022uF 100V ±5% 2
135-3107m16 electrolytic 100uF 16V ±20% 1
135-4688m50 electrolytic 6800U/50V ±20% D25X45mm 2
Semiconductors
192-027c1815gr Transistor 2SA1815GR NPN 5
192-028a1015gr Transistor 2SA1015GR PNP 2
192-1572n5551 Transistor 2N5551 NPN 2
192-1582n5401 Transistor 2N5401 AI-PNP 350V 500MA TO-92 2
197-031n4148 diode 100mA 75V SIGNAL 1N4148 ROHM 4
199-15000335 zener diode3.3V 1/2W 52mm 1
199-15000625 zener diode 6.2V 1/2W 52mm 2
199-15001605 zener diode 16V 1/2W 52mm 1
190-06m4558d IC OPA 4558D DUAL OP-AMP 1
192-021tip35c Transistor TIP35C NPN 1
192-022tip36c Transistor TIP36C PNP 1
192-027c1815gr Transistor 2SC1815GR NPN 2
192-201d882Y TransistorKSD882Y PNP 1
C116
C108.113.115.119
C106
C139,140
C107
C124,125,126,128
C105,112
C109,117,120
C114,118
C129,130
C111
C103
C123,127
C110
C121,122
Q102,111,112,113,118
Q114,116
Q103,109
Q104,110
D101,103,105,108
D102
D106,107
D109
U101
Q107
Q108
Q101,115
Q117
y
L
22
TSS-Sub500
Part Number
Description
POWER/MAIN PCB
Reference Designator
Qt
192-202b772y TransistorKSD772Y PNP 1
192-991d669a TransistorHI-SINCERITY HSD669A NPN 1
192-992b649t Transistor HSB649T PNP 1
197-00kb1405 diode 4A500V KBL405 BRIDGE 1
197-101n4002 diode IN4002 1
Miscellaneous
162-10202001 wire 26AWC 1007 200mm RED 1
171-udhss124d relay 5A 24V UDH-SS124D 1
175-1c07v01 wire connector 7PIN PITCH=2.5mm 1
175-1d02v01 wire connector 2PIN PITCH=3.96mm 1
175-1d03v01 wire connector 3PIN PITCH=3.96mm 1
193-3m2520 insulator TO-3P 25x20mm 2
LIMITER PCB
110-16103j26 Resistor 10K 1/6W ±5% CF 26mm 8
110-16183j26 Resistor 18K 1/6W ±5% CF 26mm 1
110-16223j26 Resistor 22K 1/6W ±5% CF 26mm 2
110-16273j26 Resistor 27K 1/6W ±5% CF 26mm 1
110-16333j26 Resistor 33K 1/6W ±5% CF 26mm 1
110-16472j26 Resistor 4.7K 1/6W ±5% CF 26mm 2
110-16474j26 Resistor 470K 1/6W ±5% CF 26mm 1
110-16751j26 Resistor 750Ω 1/6W ±5% CF 26mm 2
110-16755j26 Resistor 7.5k 1/6W ±5% CF 26mm 1
130-2f104z503 disc Capacitor 0.1u 50V +80/-20% 2
132-103j503 mylar Capacitor 0.01U 50V ± 5% 2
135-3226m50 electrolytic 22U 50V ± 20% 2
135-3476m25 electrolytic 47U 25V ± 20% 1
192-027c1815gr Transistor 2SC1815gr NPN 2
197-031n4148 diode 100mA 75V SIGNAL 1N4148 2
162-50289001 CABLE ASS'Y wire's 280mm AWG26 WHT 1
175-9f40hr2 coupling 40PIN PITCH=2.54mm HR2*40 0.15
190-16tl074cn I .C TL074cm st QUAD OP-AMP 1
Q119
Q106
Q105
D110
D104
RY101
P101
P102
P103
for Q107,108
R301,303,304,308,309,314,340,344
R302
R310,312
R341
R305
R342,343
R307
R311,313
R306
C305,306
C302,303
C301,340
C304
Q301,302
D301,302
P301
U301
MISCELLANEOUS/MECHANICA
123-14j70d Ferrite Core U-16.3*8.2*13(J70)+CASE 1
130-3f472md00 disc Capacitor 4700P 400V ± 20% 1
150-e8604107 Power Transformer EI-86 60HZ 120V TT086996580 1
152-u602015 LineCord SVT FT-2 6FT 1
154-u25006t0 Fuse 2.5A 250V 20mm 1
155-520020 Fuse Holder R3-11 1
162-10082007 WIRE RED 18AWG 80mm 8mm#1015 1
162-50652003 WIRE 650mm RED=205# 0.5T BLK=110# 0.5T 1
176-wjcel wire connector Pin CE-1 1
180-prf1003S switch ROCK RF-1003-BB2-OHA POWER 1
176-wjce1 wire connector pin CE-1 1
350-EM04012D024 4￠*12 wood screw black 4
351-HM04016A218 M4*16 machine screw black 4
351-AM03008A079 M3*8 machine screw black 6
352-AM03010D065 ￠3*10 P type tapping screw black 2
352-AM03008D040 ￠3*8 B type tapping screw black 8
354-GM04002 M4 nut black 4
362-FE-00013 PCB support L TYPE t=1.6mmS.P.C.C 89*9*1.6T 2
311-ABS-00028 plastic knob 46077-W soft matetial P.V.C. LEVEL 1
335-NYL-00002 wire clip 4K-4 NO-BB 2
C001
T1
SW100
y
L
23
TSS-Sub500
Part Number
Description
MISCELLANEOUS/MECHANICA
333-EVA-00783 EVA W 198*12*2.0T 2
333-EVA-00807 EVA L 274*12*2.0T 2
333-EVA-00826 EVA W 198*12*1.0T 2
333-EVA-00835 EVA L 274*12*1.0T 2
320-RUB-00033 rubber foot pad 25*21*4t 4
337-CU-00101 copper foil 65L*50W 1
306-ABS-00177 rear Plastic housing 198*298*102mm 1
162-50552003 WIRE UL1007 #16 550mm#110/#205 0.5T 1
302-AL-05048-0BAE rear board 300*200*2.5T black(RoHS) 1
323-AL-00106-0BB HEAT SINK 117.5*71.5*25 anode is black 1
Reference Designator
Qt
24
TSS-Sub500
25
TSS-Sub500
26
TSS-Sub500
Loading...