INDESIT IWB 70852 C ECO HK User Manual

Instructions for use

WASHING MACHINE

GB

English,1

IWB 70852 C ECO HK

Contents

Installation, 2-3-4-5

Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data

Care and maintenance, 6

Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose

Precautions and tips, 7

General safety
Disposal

Description of the washing machine
and starting a wash cycle, 8-9

Control panel
Indicator lights
Starting a wash cycle

GB

Wash cycles, 10

Table of wash cycles

Personalisation, 11

Setting the temperature
Functions

Detergents and laundry, 12

Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system

Troubleshooting, 13

Service, 14

1

Installation

GB

! This instruction manual should be kept in a safe

place for future reference. If the washing machi­ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him­self/herself with its operation and features.
! Read these instructions carefully: they con­tain vital information relating to the safe instal­lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its
packaging.

2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.

3. Remove the 3 pro­tective screws and the
rubber bush with the
respective spacer, si­tuated on the rear of
the appliance (see also

the installation leaflet).

4. Close off the holes using the plastic plugs
provided.

5. Keep all the parts in a safe place: you will
need them again if the washing machine ne­eds to be moved to another location.

Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.

Connecting the electricity and
water supplies

Connecting the water inlet hose

1. Connect the sup­ply pipe by screwing
it to a cold water tab
using a ¾ gas threa­ded connection (see

figure).

Before performing the
connection, allow the
water to run freely un­til it is perfectly clear.

2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon­ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap­pliance (see figure).

! Packaging materials should not be used as
toys for children.

Levelling

1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni­ture cabinets or anything else.

2. If the floor is not
perfectly level, com­pensate for any une­venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu­red in relation to the
worktop, must not
exceed 2°.

2

3. Make sure that the hose is not folded over
or bent.

! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).

! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;

alternatively, rest it on
the side of a washba­sin or bathtub, faste­ning the duct sup­plied to the tap (see
figure). The free end
of the hose should
not be underwater.

! We advise against the use of hose exten­sions; if it is absolutely necessary, the exten­sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.

Electric connection

Before plugging the appliance into the mains
socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical
Data Plate fixed on the machine;

THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words
on the base of the plug. Replacements can be
obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please en­sure that either:
the plug is replaced by a fused 13 ampere rewi­reable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in complian­ce with BS 5733) which is accessible without
moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.

Instructions for connecting cable to an alterna­tive plug:
Important: the wires in the mains lead are co­loured in accordance with the following code:

Green & Yellow Earth
Blue Neutral
Brown Live

GB

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on
the machine.

• the socket is compatible with the washing
machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fu­sed plug it can be plugged into a 13 amp socket
for immediate use. Before using the appliance
please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

3

GB

GREEN &
YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR
CORD GRIP

As the colours of the wires in the lead may not
correspond with the coloured markings iden­tifying the terminals in your plug, proceed as
follows:
Connect Green & Yellow wire to terminal
marked E or or coloured Green or Green &
Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or co­loured Black.
If a 13 amp plug (BS 1363) is used it must be
fitted with a 13 amp fuse, either in the plug or
adaptor or at the distribution board.
If you are in any doubt regarding the electrical
supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:

BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)

Warning! The company denies all liability if and
when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 5.

Disposing of the appliance:

When disposing of the appliance please re­move the plug by cutting the mains cable as
close as possible to the plug body and dispo­se of it as described above.

! The washing machine should not be installed
in an outdoor environment, not even where
the area is sheltered, because it may be very
dangerous to leave it exposed to damp, rain
and thunderstorms.

! When the washing machine is installed, the
mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be repla-
ced by an authorised serviceman.

4

Technical data

GB

Model

Dimensions

Capacity

Electrical
connections

Water connec­tion

Spin speed

Energy rated
programmes
according to
regulation

- Code of Prac­tice on Energy
Labelling of
Products 2014

-

IWB 70852 C ECO HK

width 59,5 cm
height 85 cm
depth 51,7 cm

from 1 to 7 kg

please refer to the techni­cal data plate fixed to the
machine

maximum pressure
1 MPa (10 bar)
minimum pressure

0.05 MPa (0.5 bar)
drum capacity 46 litres

up to 800 rotations per
minute

programme 5; tempera­ture 60°C; using a load of
7 kg.

This appliance conforms to
the following EC Directives:

- 2004/108/CE (Electro­magnetic Compatibility)

- 2012/19/EU (WEEE)

- 2006/95/EC Low Voltage)

5