Husqvarna MZ6125, MZ7227, MZ5225BF, MZ6125BF, MZ5225C User Manual
...
Operator's Manual
MZ5225 / 968999717 MZ6125 / 968999718
MZ7227 / 968999719 MZ5225BF / 968999720
MZ6125BF / 968999721 MZ5225C / 968999748
MZ6125C / 968999749 MZ25 / 968999780
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
English
©2008 HTC. All rights reserved.
Beatrice, NE. Printed in U.S.A.
CONTENTS
INTRODUCTION ............................................................... 5
General ....................................................................... 5
Driving and Transport on Public Roads ...................... 5
Towing......................................................................... 5
Operating .................................................................... 5
Good Service .............................................................. 6
SYMBOLS AND DECALS ................................................. 7
SAFETY ............................................................................ 9
Safety Instructions ...................................................... 9
General Operation ...................................................... 9
Personal Safety Equipment ...................................... 11
Slope Operation ........................................................ 11
Safe Handling of Gasoline ........................................ 13
General Maintenance ...............................................14
Transport ..................................................................16
Roll over Protection system (ROPS) ........................17
CONTROLS .................................................................... 18
Control Locations ...................................................... 18
Steering Control Levers ............................................ 19
Parking Brake ........................................................... 20
Throttle Control ......................................................... 20
Blade Switch ............................................................. 20
Ignition Switch........................................................... 21
Choke Control ........................................................... 21
Fuses ........................................................................ 21
Fuel Tank ..................................................................22
Fuel Shut Off Valve ................................................... 23
Hour Meter ................................................................ 24
Tracking Knob ........................................................... 24
OPERATION ................................................................... 25
Training ..................................................................... 25
Steering ....................................................................25
Before Starting .......................................................... 26
Starting the Engine ................................................... 26
Jumper cables ................................................30
Running ....................................................................31
Operating on hills ...................................................... 32
Mowing Tips ............................................................. 33
Stopping the Engine .................................................34
Pump release valves ................................................35
MAINTENANCE .............................................................. 36
Maintenance Schedule ............................................. 36
Battery ......................................................................38
Ignition System ......................................................... 39
Safety System........................................................... 39
Engine Cooling Air Intake ......................................... 40
Throttle Cable ........................................................... 40
Choke Cable ............................................................ 40
Air Filter Maintenance ............................................... 41
Replacing Air Filter..........................................41
Servicing Precleaner....................................... 41
Servicing Paper Element ................................ 41
Replacing the Fuel Filter ........................................... 42
Tire Pressures ..........................................................42
Parking Brake ........................................................... 43
V-belts ....................................................................... 43
Deck belt ................................................................... 44
Pump Belt ................................................................. 45
Cutting Blades ..........................................................45
Blade replacement .......................................... 46
Adjusting the Mower Deck ........................................ 47
Leveling deck .................................................. 47
Anti-scalp rollers ............................................. 48
Cleaning and Washing .............................................. 49
Caster Wheels .......................................................... 49
Hardware .................................................................. 49
LUBRICATION ................................................................ 50
Lubricating the Cables .............................................. 51
Front Wheel Mount ................................................... 51
Front Wheel Bearings ............................................... 51
Deck spindle ............................................................. 51
Engine Oil ................................................................. 52
Engine Oil Filter .............................................. 52
Changing the Engine Oil ................................. 52
Engine Oil Levels ............................................ 53
Hydraulic Pump .......................................................54
Fluid Change ..................................................54
Purging Procedures ........................................ 54
TROUBLESHOOTING .................................................... 55
STORAGE ....................................................................... 57
Storage ..................................................................... 57
Service ...................................................................... 57
SCHEMATICS ................................................................. 58
TECHNICAL DATA .......................................................... 59
Accessories ..............................................................63
Torque Specications................................................ 63
CONFORMITY CERTIFICATES ..................................... 65
SERVICE JOURNAL ....................................................... 66
After the First 5-8 Hours ...........................................67
25-Hour Service ........................................................ 68
50-Hour Service ........................................................ 69
100-Hour Service ...................................................... 70
300-Hour Service ...................................................... 71
At Least Once Each Year.......................................... 72
WARNING!
Failure to follow cautious operating practices can result in serious injury to the
operator or other persons. The owner must understand these instructions, and must
allow only trained persons who understand these instructions to operate the mower.
Each person operating the mower must be of sound mind and body and must not be
under the inuence of any mind altering substance.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain
or emit chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm.
WARNING!
Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
INTRODUCTION
Congratulations
Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efciency to rapidly mow
primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by
steering controls both contribute to the machine’s performance.
This manual is a valuable document. Read the contents carefully before using or servicing the machine. The
following of instructions (use, service, maintenance, etc.) by all who operate this machine is important for the
safety of the operator and others. It can also considerably increase the life span of the machine and increase its
resale value.
If you sell your machine, be sure to give the operator’s manual to the new owner.
The nal chapter of this operator’s manual provides a Service Journal. Ensure that service and repair work are
documented. A well-kept service journal reduces service costs for the maintenance and affects the machine’s
resale value. Please contact your dealer for more information. Take the operator’s manual along when the
machine is taken to your dealer for service.
General
In this operator’s manual, left and right, backward and forward are used in relation to the machine’s normal driving
direction.
Continuous dedication to improve our products require that specications and design are subject to change
without notice.
Driving and Transport on Public Roads
Check applicable road trafc regulations before transporting on public roads. If the machine is transported, you
must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate
this machine on public roadways.
Towing
Do not tow this machine, it may cause damage to the drive system.
Do not tow any trailers, etc. with this mower. They may jackknife or overturn causing damage to the mower and
possible serious injury to the operator.
Operating
This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones,
tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided
by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses
are incorrect. The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully
followed.
Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good
judgement, careful use in accordance with these instructions and common sense.
The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special
characteristics and who are also knowledgeable about the safety instructions. Use only approved repair parts to
maintain this machine.
Accident prevention regulations, other general safety regulations, occupational safety rules, and trafc regulations
must be followed without fail.
Unauthorized modications to the design of the machine may absolve the manufacturer from liability for any
resulting personal injury or property damage.
English-5
INTRODUCTION
Good Service
Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This
ensures that you as a customer receive only the best support and service. Before the product is delivered, the
machine has, for example, been inspected and adjusted by your retailer. See the certicate in the Service Journal
in this operator’s manual.
When you need spare parts or support in service questions, warranty issues, etc., please consult the following
professional:
This Operator’s Manual belongs to the machine with
the manufacturing number:
Manufacturing Number
The machine’s manufacturing number can be found on the printed plate afxed to the left in the engine
compartment. Stated on the plate, from the top are:
The machine’s type designation (I.D.).•
The manufacturer’s type number (Model).•
The machine’s serial number (Serial no.)•
Please have the type designation and serial number available when ordering spare parts.
The engine’s manufacturing number is stamped on one of the valve covers.
The plate states:
The engine’s model.•
The engine’s type.•
Code•
Please have these available when ordering spare parts.
The wheel motors and hydrostatic pumps have a barcode decal afxed at the rear.
Engine
Transmission
English-6
SYMBOLS AND DECALS
These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.
WARNING!
Xxxx xxxxxx xxxxx xxxx
xxxxxxxxx xxxxxx xxxxxxxxx.
xx xxxxxxxx xxxx xxxxxx.
Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should
neglect to follow instructions given in the manual.
IMPORTANT INFORMATION
Xxxx xxxxxx xxxxx xxxx xxxxxxxxx
xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx
xxxxxx.
Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect
to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.
R N
Reverse Neutral Fast Slow Choke Fuel
P
Warning! Parking Brake CE conformity Warning! Rotating blades, Do not touch parts
marking. Only for keep away from the
European market discharge deck
Battery acid is corrosive, explosive and ammable Do not stand here
Noise emissions to the
surroundings in accordance
with the European Union’s
directive. The machine’s
emission is stated in the
chapter TECHNICAL DATA
and on the decals.
Use protective glasses Use protective gloves
Only machines for European
market
English-7
SYMBOLS AND DECALS
Read Shut off engine and Keep a safe Use on slopes No passengers
Operator’s remove key before distance from no greater
Manual performing any the machine than 10°
maintenance or repair work
Whole body Severing of ngers Do not open or Careful backing up, Careful going
exposure to and toes remove safety watch for other forward, watch for
thrown objects shields while people other people
engine is running
Moving sharp blades under cover
English-8
SAFETY
Safety Instructions
These instructions are for your safety. Read them carefully.
WARNING!
This symbol means that important safety instructions need to be emphasized.
It concerns your safety.
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING
OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
General Operation
Read, understand, and follow all instructions •
on the machine and in the manual before
starting.
Do not put hands or feet near rotating parts •
or under the machine. Keep clear of the
discharge opening at all times.
Only allow responsible adults, who are •
familiar with the instructions, to operate the
machine.
Clear the area of objects such as rocks, toys, •
wire, etc., which could be picked up and
thrown by the blades.
Be sure the area is clear of bystanders •
before operating. Stop machine if anyone
enters the area.
Never carry passengers. The machine is only •
intended for use by one person.
Do not mow in reverse unless absolutely •
necessary. Always look down and behind
before and while backing.
Never direct discharged material toward •
anyone. Avoid discharging material against
a wall or obstruction. Material may ricochet
back toward the operator. Stop the blades
when crossing gravel surfaces.
Do not operate machine without the entire •
grass catcher, discharge guard, or other
safety devices in place and working
Slow down before turning.•
Never leave a running machine unattended. •
Always turn off blades, set parking brake,
stop engine, and remove keys before
dismounting.
Disengage blades when not mowing. Shut •
off engine and wait for all parts to come to a
complete stop before cleaning the machine,
removing the grass catcher, or unclogging
the discharge chute.
Read the operator’s manual before starting the machine
Clear the area of objects before mowing
8011-512
8011-513
English-9
SAFETY
Operate machine only in daylight or good •
articial light.
Do not operate the machine while under the •
inuence of alcohol or drugs.
Watch for trafc when operating near or •
crossing roadways.
Use extra care when loading or unloading •
the machine into a trailer or truck.
Always wear eye protection when operating •
machine.
Data indicates that operators age 60 years •
and above are involved in a large percentage
of riding mower-related injuries. These
operators should evaluate their ability to
operate the riding mower safely enough to
protect themselves and others from serious
injury.
Follow the manufacturer’s recommendation •
for wheel weights or counterweights.
Anyone who operates this machine must rst •
read and understand this Operation Manual.
Local laws may regulate the age of the user.
Keep machine free of grass, leaves or other •
debris buildup which can touch hot exhaust
/ engine part and burn. Do not allow the
mower deck to plow leaves or other debris
which can cause buildup to occur. Clean any
oil or fuel spillage before operating or storing
the machine. Allow machine to cool before
storage.
8011-520
Never take passengers
WARNING!
Engine exhaust and certain
vehicle components contain
or emit chemicals considered
to cause cancer, birth defects,
or other reproductive system
damage. The engine exhaust
contains carbon monoxide,
which is a odorless, colorless,
poisonous gas. Do not use the
machine in enclosed spaces.
English-10
SAFETY
Personal Safety Equipment
WARNING!
When using the machine, approved personal protective equipment (shown in
illustrations) shall be used. Personal protective equipment cannot eliminate the
risk of injury but it will reduce the degree of injury if an accident does happen.
Ask your retailer for help in choosing the right equipment.
Make sure that you have rst aid equipment •
close at hand when using the machine.
Never use the machine when barefoot. •
Always wear protective shoes or boots, •
preferably with steel toe caps.
Always wear approved protective glasses or •
a full visor when assembling or driving.
Always wear gloves when handling the •
blades.
Never wear loose clothing that can get •
caught in moving parts.
Use ear protectors to avoid damage to •
hearing.
Slope Operation
Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on
it, do not mow it.
Mow up and down slopes (10 degrees •
maximum), not across.
Watch for holes, ruts, bumps, rocks, or •
other hidden objects. Uneven terrain could
overturn the machine. Tall grass can hide
obstacles.
Choose a low ground speed so that you will •
not have to stop while on the slope.
Do not mow on wet grass. Tires may lose •
traction.
Avoid starting, stopping, or turning on a •
slope. If the tires lose traction, disengage the
blades and proceed slowly straight down the
slope.
Keep all movement on the slopes slow and •
gradual. Do not make sudden changes in
speed or direction, which could cause the
machine to roll over.
Use extra care while operating machine with •
grass catchers or other attachments; they
can affect the stability of the machine.
8011-670a
Personal protective equipment
6003-004
Mow up and down, not side to side
WARNING!
Do not drive up or down hills
with slopes greater than 10
degrees. And do not drive across
any slopes.
English-11
SAFETY
Do not use on steep slopes.•
Do not try to stabilize the machine by putting •
your foot on the ground.
Do not mow near drop-offs, ditches, or •
embankments. The machine could suddenly
roll over if a wheel is over the edge or if the
edge caves in.
Children
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are often
attracted to the machine and the mowing activity.
Never assume that children will remain where you last
saw them.
Keep children out of the mowing area and in •
the watchful care of a responsible adult other
than the operator.
Be alert and turn machine off if a child enters •
the area.
Before and while backing, look behind and •
down for small children.
Never carry children, even with the blades •
shut off. They may fall off and be seriously
injured or interfere with safe machine
operation. Children who have been given
rides in the past may suddenly appear in
the mowing area for another ride and be run
over or backed over by the machine.
Never allow children to operate the machine.•
Use extra care when approaching blind •
corners, shrubs, trees, or other objects that
may block your view of a child.
8011-509
Be extra cautious when driving on slopes
8011-517
Never allow children to operate the machine
English-12
8011-518
Keep children away from work area
SAFETY
WARNING!
The engine must not be started when the driver’s oor plate or any protective
plate for the mower deck’s drive belt is removed.
Safe Handling of Gasoline
To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline is
extremely ammable and the vapors are explosive.
Extinguish all cigarettes, cigars, pipes, and •
other sources of ignition.
Use only approved gasoline container.•
Never remove gas cap or add fuel with the •
engine running. Allow engine to cool at least
two (2) minutes before refueling.
Never fuel the machine indoors.•
Never store the machine or fuel container •
where there is an open ame, spark, or pilot
light such as on a water heater or other
appliance.
Before you begin refueling, minimize the •
risk of static electricity by touching a metal
surface.
Never ll containers inside a vehicle or on a •
truck or trailer bed with plastic liner. Always
place containers on the ground away from
the vehicle when lling.
Remove gas-powered equipment from the •
truck or trailer and refuel it on the ground. If
this is not possible, refuel such equipment
with a portable container, rather than from a
gasoline dispenser nozzle.
Keep the nozzle in contact with the rim of the •
fuel tank or container opening at all times
until fueling is complete. Do not use a nozzle
lock-open device.
If fuel is spilled on clothing, change clothing •
immediately.
Never overll fuel tank. Replace gas cap and •
tighten securely.
Do not start the engine near spilled fuel.•
Never use gasoline as a cleaning agent.•
If leaks arise in fuel system, engine must not •
be started until problem has been resolved.
Check the fuel level before each use and •
leave space for the fuel to expand, as the
heat from the engine and the sun may
otherwise cause the fuel to expand and
overow.
8011-516
Never ll the fuel tank indoors
WARNING!
The engine and the exhaust
system become very hot during
operation.
There is risk for burns if
touched.
Allow engine and exhaust
system to cool at least two (2)
minutes before refueling.
English-13
General Maintenance
Never operate machine in a closed area.•
Keep all nuts and bolts tight to be sure the •
equipment is in safe working condition.
Never tamper with safety devices. Check •
their proper operation regularly.
Keep machine free of grass, leaves, or other •
debris buildup. Clean oil or fuel spillage
and remove any fuel-soaked debris. Allow
machine to cool before storing.
If you strike a foreign object, stop and •
inspect the machine. Repair, if necessary,
before restarting.
Never make any adjustments or repairs with •
the engine running.
Check grass catcher components and the •
discharge guard frequently and replace with
manufacturer’s recommended parts, when
necessary.
Mower blades are sharp. Wrap the blade or •
wear gloves, and use extra caution when
servicing them.
Check brake operation frequently. Adjust and •
service as required.
Maintain or replace safety and instruction •
labels, as necessary.
Do not modify safety equipment. Check •
regularly to be sure it works properly. The
machine must not be driven with defective
or unmounted protective plates, protective
cowlings, safety switches, or other protective
devices.
Do not change the settings of governors and •
avoid running the engine with overly high
engine speeds. If you run the engine too fast,
you risk damaging the machine components.
Be very careful when handling battery acid. •
Acid on skin can cause serious corrosive
burns. If you spill battery acid on your skin,
rinse immediately with water.
Acid in the eyes can cause blindness, •
contact a doctor immediately.
Be careful when servicing the battery. •
Explosive gases form in the battery. Never
perform maintenance on the battery when
smoking or near open ames or sparks.
The battery can explode and cause serious •
injury/damage.
SAFETY
8011-515
Never drive the machine in an enclosed space
Use protective glasses for
maintenance work.
WARNING!
The battery contains lead and
lead compounds, chemicals
that are considered to cause
cancer, birth defects, and other
reproductive system damage.
Wash your hands after handling
the battery.
English-14
SAFETY
Ensure that nuts and bolts, especially the •
fastening bolts for the blade attachments,
are properly tightened, torqued and that the
equipment is in good condition.
Do not modify safety equipment. Check •
regularly to be sure it works properly. The
machine must not be driven with defective
or unmounted protective plates, protective
cowlings, safety switches, or other protective
devices.
Do not change the settings of governors and •
avoid running the engine with overly high
engine speeds. If you run the engine too fast,
you risk damaging the machine components.
Sparking can occur when working with the •
battery and the heavy cables of the starter
circuit. This can cause battery explosion,
re or eye injury. Sparking in this circuit can
not occur after the chassis cable (normally
negative, black) is removed from the battery.
6003-009
Do not smoke when performing maintenance on the battery.
The battery can explode and cause serious injury/damage.
WARNING!
Avoid electrical sparking and its
consequences by the following
routines:
Use protective goggles.•
Ensure that the fuel ller cap is mounted •
tightly and no ammable substances are
stored in an open vessel.
Never work with the starter circuit if there is •
spilled fuel.
Disconnect the chassis cable from the •
battery rst and reconnect it last.
Do not make a bridge short circuit across the •
starter relay to run the starter.
Never use the machine indoors or in spaces •
lacking proper ventilation. The exhaust
fumes contain carbon monoxide, an
odorless, poisonous, and lethal gas.
Stop and inspect the equipment if you run •
over or into anything. If necessary, make
repairs before starting.
Never make adjustments with the engine •
running.
The machine is tested and approved only •
with the equipment originally provided or
recommended by the manufacturer. Only use
approved repair parts for the machine.
8009-728
Risk of sparking
English-15
The blades are sharp and can cause •
cuts and gashes. Wrap the blades or use
protective gloves when handling them.
Check the parking brake’s functionality •
regularly. Adjust and service as necessary.
The mulch blades should only be used in •
familiar areas when higher quality mowing is
desired.
Reduce the risk of re by removing grass, •
leaves, and other debris that may have
accumulated on the machine. Allow the
machine to cool before putting it in storage.
Regularly clean deck and underside of •
deck, avoid spraying engine and electrical
components with water.
Transport
The machine is heavy and can cause serious •
crushing injuries. Be extra cautious when it
is loaded on or unloaded from a vehicle or
trailer.
Use an approved trailer to transport the •
machine. Activate the parking brake, turn off
the fuel supply, and fasten the machine with
approved fastening devices, such as bands,
chains, or straps, when transporting.
Do not operate this machine on public •
roadways.
Check and abide by local trafc regulations •
before transporting the machine on any road.
Do not tow this machine, it may cause •
damage to the drive system.
Do not tow any trailers, etc. with this mower. •
They may jackknife or overturn causing
damage to the mower and possibly serious
injury to the operator.
Load the unit onto truck or trailer by driving •
up ramps of suitable strength using a slow
speed. Do not lift! The machine is not
intended to be lifted by hand.
SAFETY
8011-514
Regularly clean deck
WARNING!
Escaping hydraulic oil under
pressure can have sufcient
force to penetrate the skin,
causing serious injury. If injured
by escaping uid, see a doctor
at once. Serious infection or
reaction can develop if proper
medical treatment is not
administered immediately.
IMPORTANT INFORMATION
The parking brake is not sufcient
to lock the machine in place during
transport. Ensure that the machine is
well fastened to the transport vehicle.
Always reverse the machine onto the
transport vehicle to avoid tipping it over.
English-16
SAFETY
Roll over Protection system (ROPS)
The ROPS increases the basic weight of the unit by 42
lbs/19 kg. The ROPS is an accessory.
Do not use ROPS as a lifting, attaching or •
anchoring point.
Do not use ROPS for wrecking or towing.•
Do not exceed Max GVW: 2822 lbs/1283 kg.•
Read machine operator´s manual before •
each use.
Securely fasten your seat belt if the unit has •
a ROPS.
Where possible, avoid operating the unit •
near ditches, embankments and holes.
Reduce speed when turning, crossing •
slopes and on rough, slick or muddy
surfaces.
Stay off slopes too steep for safe operation.•
Watch where you are going, especially at •
row ends, on roads and around trees.
Do not permit others to ride.•
Operate the mower smoothly - no jerky •
turns, starts or stops.
When mower is stopped, set brakes •
securely and use park brake.
If any part of ROPS is damaged, the entire •
ROPS must be replaced.
Check all bolts including seat belt for correct •
torque before each use.
Check ROPS structure for damage before •
each use.
ROPS bar is NOT intended for use in sub •
zero temperatures.
WARNING!
The rollover protection
system's capabilities may
be impaired by damage if
the mower is overturned
or if alteration to the ROPS
occurs. If these conditions
take place, the total structure
MUST be replaced.
WARNING!
This mower is equipped
with an internal combustion
engine and should not
be used on or near any
unimproved forested, bush
covered or grassy lands
unless the engine's system
is equipped with a spark
arrester meeting applicable
local or state laws (if any).
If a spark arrester is used,
it should be maintained in
effective working order by
the operator.
English-17
CONTROLS
This operator’s manual describes the Husqvarna
Zero Turn Rider. The rider is tted with a Kohler four-
stroke overhead valve engine developing 25-27 horse
power*.
Control Locations
89
7
Transmission from the engine is made via a belt-driven
hydraulic pumps. Using the left and right steering
controls, the ow is regulated and thereby the direction
and speed.
13
2
1
10
Motion control levers1.
Parking brake2.
Throttle control3.
Blade switch4.
Ignition switch5.
Choke control6.
Fuses7.
*As rated by the engine manufacturer.
11
12
3456
Fuel tank cap8.
Fuel shut off valve9.
Deck lift10.
Seat adjustment lever11.
Hour meter12.
Tracking knob13.
English-18
CONTROLS
1
2
3
4
1. Steering Control Levers
The machine’s speed and direction are continuously
variable using the two steering controls. The steering
controls can be moved forward or backward about
a neutral position. Furthermore, there is a neutral
position, which is locked if the steering controls are
moved outward.
When both controls are in the neutral position (N), the
machine stands still.
By moving both controls an equal amount forward
or backward, the machine moves in a straight line
forward or backward respectively.
In order, for example, to turn right while moving
forward, move the right control towards the neutral
position. The rotation of the right wheel is reduced and
the machine turns to the right.
Zero turn can be achieved by moving one control
backward (behind the neutral position) and carefully
moving the other steering control forward from its
neutral position. The rotation direction when zero
turning is determined by which steering control is
moved backward behind the neutral position. If the left
steering control is pulled backward, the machine turns
to the left. Use extra care when using this maneuver.
If the steering controls are in uneven positions when
standing still or do not t in the slots for moving the
controls outward, they can be adjusted.
8011-789
Steering controls
WARNING!
The machine can turn very
rapidly if one steering control
is moved much further forward
than the other.
1. Forward
2. Neutral
3. Neutral slot, Neutral lock
4. Reverse
Motion control lever, right side
8011-7912
English-19
CONTROLS
2. Parking Brake
IMPORTANT INFORMATION
The machine must stand absolutely still
when applying the parking brake. Always
set the parking brake before dismounting.
Release the parking brake before moving
the mower.
The parking brake is found on the left of the machine.
Pull the lever backward to activate the brake and
forward to release it.
3. Throttle Control
The throttle control regulates the engine speed and
thereby the rate of rotation of the blades, assuming the
blade switch is pulled out, see Engaging the Mower
Deck.
In order to increase or decrease the engine speed, the
control is moved forward or back respectively.
Avoid idling the engine for long periods, as there is a
risk of fouling the spark plugs.
USE FULL THROTTLE WHEN MOWING, for best
mower performance and battery charging.
8061-010
Parking brake not activated
4. Blade Switch
In order to engage the mower deck, pull the knob out;
the mower blades are disengaged when the knob is
depressed.
English-20
8061-001
Throttle control
8061-002
Blade switch
CONTROLS
5. Ignition Switch
The ignition key is placed on the control panel and is
used to start and stop the engine.
6. Choke Control
The choke control is used for cold starts in order to
provide the engine with a richer fuel mixture.
For cold starts the control should be pulled out to its
extent.
8061-003
Ignition switch
7. Fuses
Fuses are located on the left hand side of the machine.
They are accessed by tilting the seat forward. They are
at pin fuses of the same type used in automobiles.
There are two fuses with ratings and functions:
20 A, Primary fuse.•
7.5 A, Mower deck coupling.•
8061-004
Choke control
8011-420
Fuses
English-21
CONTROLS
8. Fuel Tank
Read the safety instructions before refueling. The
machine has one fuel tank, just behind the seat. The
tank capacity is 5.7 gallons (22 liters).
Make sure the fuel cap is properly tightened and the
cap gasket is not damaged.
The engine will run on a minimum of 85-octane
unleaded gasoline (no oil mix). Environmentally
adapted alkylate gasoline can be used. See also
Technical Data concerning ethanol fuel. Methanol fuel
is not allowed. Do not use E85 alcohol based fuel.
Damage to engine and components may occur.
WARNING!
Gasoline is highly ammable.
Observe caution and ll the
tank outdoors (see the safety
instruction).
WARNING!
The engine and the exhaust
system, become very hot during
operation.
Risk for burns if touched.
Allow engine and exhaust
system to cool at least two (2)
minutes before refueling
WARNING!
8011-625
Fuel tank
IMPORTANT INFORMATION
Experience indicates that alcohol blended
fuels (called gasohol, ethanol or methanol)
can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. To
avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start the
engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel the
next season. See Storage Instructions for
additional information. Never use engine
or carburetor cleaners in the fuel tank or
permanent damage may occur.
Fill to bottom of ller neck. Do
not overll. Wipe off any spilled
oil or fuel. Do not store, spill
or use gasoline near an open
ame.
When operating in temperatures below 32° F. (0° C.),
use fresh, clean winter grade gasoline to help insure
good cold weather starting.
English-22
CONTROLS
9. Fuel Shut Off Valve
The fuel shut off valve is located at the left rear of the
seat. The valve is off when the handle tab is turned
perpendicular to the fuel line.
10. Lifting Lever for the Mower Deck
The lifting lever is used to transfer the mower deck
from the transport position into the preferred cutting
height position.
To set the cutting height, pull out the detent ring and
place it in the desired height’s corresponding hole.
To lower the deck from the transport position, press
forward on the foot pedal while pulling back on the
transport latch. This releases it from the locked
position and allows it to ease down to the detent pin,
setting the selected cutting height.
8011-419
Fuel shut off valve in the CLOSED position.
1
2
3
IMPORTANT INFORMATION
In order to obtain an even cutting height,
it is important that the air pressure in the
front tires is 15 psi and the rear tires is 10
psi.
IMPORTANT INFORMATION
Always use the high position to transport.
8061-007
1. Detent Pin
2. Transport latch
3. Foot Pedal
The mower deck’s lifting lever
English-23
CONTROLS
11. Seat Adjustment Lever
The seat can be adjusted lengthways. When making
adjustments, the lever under the front edge of the
seat is moved to the left (as seen by the driver in the
seat), after which the seat can be moved backward or
forward.
12. Hour Meter
The hour meter displays the total operating time.
It will ash CHG OIL (Change Oil) at 50 hour intervals.
The ash duration is one hour before and one hour
after the interval. The CHG OIL icon will come on
and shut off automatically. The hour meter cannot be
manually reset.
8011-441
Lengthways adjustment
13. Tracking Knob
If the mower is not tracking straight, check the air
pressure in both rear tires. Recommended air pressure
is 10 psi. (.7 bar) for the front tires and 15 psi (1 bar)
for the rear tires. Tracking must be checked on a at
and level concrete or blacktop surface.
Rotating the tracking knob allows ne tuning
adjustments so the machine tracks straight with the
steering control levers in the full forward position.
Rotate the knob clockwise (as viewed from the
operation position) to increase the speed on the left
lever. Rotate counterclockwise to decrease speed.
English-24
8011-441
Hour meter
8011-441
Lengthways adjustment
Loading...