Husqvarna K750 SPEEDMILL Manual

Operator’s manual & spare parts list.

It is the owner’s responsibility to ensure that all operators of this machine have read and understood the content of this manual before using the product! Careless or improper use of this machine can cause serious or even fatal injury! Allow only competent adults to operate this machine!

K 750

SpeedMill

SpeedMill

TABLE OF CONTENTS

Section	Page No.	Section	Page No.
Table of Contents..............................................	2	Uses...................................................................	7
Contact Information..........................................	2	Tools..................................................................	7
Symbols.............................................................	3	Assembly......................................................	7 - 8
Introduction.......................................................	4	Operation......................................................	7 - 8
Safety Instructions......................................	4 - 5	Maintenance....................................................	10
What-Is-What (Part Identification)...................	6	Spare Parts...............................................	10 - 11

CONTACT INFORMATION

Husqvarna Construction Products, North America

Corporate Office

17400 West 119th Street, Olathe, Kansas 66061 USA

Corporate Office: 913-928-1000

Corp. Office Fax: [phone]

www.husqvarnacp.com

For local service, please contact your local Husqvarna Construction Products representative.

Para efectuar un servicio local, póngase en contacto con su representante local de Husqvarna Construction Products.

Pour toute réparation, contacter le représentant local de Husqvarna Construction Products.

Für Service vor Ort wenden Sie sich bitte an Ihren örtlichen Vertreter von Husqvarna Construction Products.

Neem voor plaatselijke service contact op met uw plaatselijke vertegenwoordiger van de constructieproducten van Husqvarna.

Per assistenza, rivolgersi al rappresentante di zona della Husqvarna Construction Products.

För service på platsen, kontakta din lokala representant för Husqvarna Construction Products. Para obter serviço técnico local, contactar o representante da Husqvarna Construction Products

Husqvarna Construction Products, North America

17400 West 119th Street, Olathe, Kansas 66061 USA

Toll-Free Telephone: [phone], Telephone: [phone], Fax: [phone]

SpeedMill

SAFETY SYMBOLS & DECALS

Key to symbols

WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

•Protective helmet

• Hearing protection

• Protective goggles or a visor

WARNING! Dust forms when cutting, this can cause injuries if inhaled. Use an approved breathing mask. Avoid inhaling petrol fumes and exhaust fumes. Always provide for good ventilation.

WARNING! Sparks from the cutting blade can cause fire in combustible materials such as: petrol (gas), wood, dry grass etc.

Operator must wear eye protection!

Operator must wear hearing protection!

Operator must wear respiratory protection!

(Reference OSHA 29CFR 1910.95, 1910.133-138)

Operator must wear head protection such as a hard hat!

Operator must wear protective footwear such as safety shoes or safety boots!

The operator must wear protective clothing appropriate to the work he is doing. Never wear loose clothing or jewelry. Keep long hair tied back. Keep your hair, clothing, and gloves away from the rotating tool!

The working area must be completely clear, well lit and all safety hazards removed.

Any persons not involved in the work, should leave the area.

FOR INFORMATION ON DECALS FOR THE SPEEDMILL, SEE THE SPARE PARTS LIST SECTION OF THIS DOCUMENT.

FOR INFORMATION ON DECALS FOR THE K 750 POWER CUTTER, SEE THE SPARE PARTS LIST FOR THE K 750.

SpeedMill

SAFETY INSTRUCTIONS

Introduction

Thank you for purchasing your new machine from Husqvarna Construction Products. We have provided important safety messages in this manual and on the machine. Please read these messages carefully. A safety message alerts you to potential hazards that could hurt you or others. Each safety message is preceded by a symbol or the safety alert symbol ( ) and one of two words, WARNING, or

CAUTION.

These signal words mean:

WARNING: Indicates a hazardous situation which, if not avoided COULD result in death or serious injury.

CAUTION: Indicates a hazardous situation, which, if not avoided, COULD result in minor or moderate injury. It may also be used to alert against unsafe practices.

Each message tells you what the hazard is, what can happen, and what you can do to avoid or reduce injury.

NOTICE: Indicates a hazardous situation which, if not avoided, COULD result in property damage. Your machine or other property can be damaged if you don’t follow this instruction.

If the label is worn, damaged, or is illegible, it should be replaced.

Contents of Package

Verify the contents of the package:

•SpeedMill Power Cutter.

•SpeedMill Bowl Assembly: 100mm (4”), 150mm (6”), and 200mm (8”) Bowls with Hub and 2.00” Nut.

•Document Package. Operation Manual for Power Cutter, Spare Parts List for Power Cutter, Operation Manual / Spare Parts List for Speed Mill Accessory (This Document).

If these items are not included in the package, contact our customer service department at the telephone number shown in this document.

Safety Instructions:

WARNING!

Before starting up machine make sure you completely read these instructions and the power cutter operation manual. Be familiar with operation of the machine before operation!

Your SpeedMill comes with two Operator’s Manual’s. This one for the SpeedMill attachment and one for the K750 power head. It is the owner’s responsibility to ensure that all operators of this SpeedMill have read and understood the content of both manuals before using the product.

WARNING!

NEVER use a SpeedMill as a standard power cutter. A SpeedMill is ONLY for USES listed in this document.

Cut only PVC plastic pipe with a machine equipped with a SpeedMill Accessory! DO NOT cut other materials.

Use ONLY High Speed Reinforced Abrasive Blades with this machine.

DO NOT use carbide tipped, wood cutting, or circular saw blades with this machine.

DO NOT use diamond or rescue blades with this machine! Cutting plastics with a diamond or rescue blade can cause kickback. The heat produced melts the material and it sticks to the blade.

DO NOT cut ductile iron pipe with a SpeedMill.

DO NOT touch Bowl when machine is running. Speed-

Mill Bowl Rotates with Blade.

Before performing any maintenance, ALWAYS locate the machine on a level surface with the engine / motor OFF and the start switch in the OFF position, and the power source disconnected.

EVACUATE PIPE CONTENTS before cutting; else EXPLOSION may occur. Static electricity from the cutting operation may cause sewer or other gas within the pipe to explode.

The working area must be completely clear, well lit and all safety hazards removed.

Any persons not involved in the work, should leave the area.

SpeedMill