For Husqvarna Parts Call 606-678-9623 or 606-561-4983
54 INCH MOWER MULCH COVER
Kit Contains:
(1) Mulch Cover
(2) Latch Hooks
(2) Weld Nuts
(2) Screws
(2) Lock washers
(2) 3/16 Flat washers
ASSEMBLE MULCH COVER (See Fig. 1)
NOTE: Pre-assemble weld nut to latch hook by in sert ing
weld nut from the top with hook pointing down.
1. Install the two latch hooks to mulch cover using screw,
3/16 washer, lock washer, and weld nut as shown.
2. Tighten hardware securely.
WELD
NUT
LATCH
HOOK
LOCK
WASHER
WASHER
3/16 X 3/4
02546
SCREW
#10 X 5/8
WELD NUT
FROM THE TOP
SCREW
#10 X 5/8
MULCH
COVER
WASHER
3/16 X 3/4
FIG. 1
INSTALL MULCH COVER (See Fig. 2)
1. Raise and hold defl ector shield in upright position.
2. Hook rear latch over latch hook spacer on back of
mower.
3. Place slot in mulch cover over tab on mower and position
cover over mower opening as shown.
4. Hook front latch into hole on front of mower.
5. Check to be sure mower opening is completely covered
by the mulch cover.
DEFLECTOR
SHIELD
TAB
KIT No. MP54A
CAUTION: Do not remove defl ector shield
from mow er. Raise and hold shield when
at tach ing mulch cover and al low it to rest
on cover while in op er a tion.
HOOK POINTS
DOWN
LATCH
HOOK
WELD
NUT
LOCK
WASHER
MULCHING MOWING TIPS
IMPORTANT:
HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN
AFTER EACH USE.
• The spe cial mulch blades will recut the grass clip pings
many times and reduce them in size so that as they fall
onto the lawn they will disperse into the grass and not
be noticed. Also, the mulched grass will biodegrade
quick ly to provide nutrients for the lawn. Always mulch
with your highest engine (blade) speed as this will pro vide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet. Wet grass tends
to form clumps and interferes with the mulch ing action.
The best time to mow your lawn is the early afternoon.
At this time the grass has dried and the newly cut area
will not be exposed to the direct sun.
• For best results, adjust the mower cutting height so
that the mower cuts off only the top one-third of the
grass blades. For ex tremely heavy mulch ing, re duce
your width of cut and mow slow ly.
• Certain types of grass and grass con di tions may re quire
that an area be mulched a second time to com pletely
hide the clippings. When doing a sec ond cut, mow
across or perpendicular to the fi rst cut path.
• Change your cutting pattern from week to week. Mow
north to south one week then change to east to west the
next week. This will help prevent matting and graining
of the lawn.
FOR FUTURE REFERENCE AND REPAIR PARTS OR DER ING, KEEP THIS INSTRUCTION SHEET WITH YOUR
TRACTORS OWNER'S MANUAL
FOR BEST PERFORMANCE, KEEP MOWER
REPAIR PARTS
KIT NO. MP54A
KEY PART DESCRIPTION
NO. NO.
2 532187298 Mulch Cover
3 532160793 Latch Hook
4 532125004 Weld Nut
5 819061216 Washer 3/16 x 3/4
6 810071000 Washer, Lock #10
7 871081010 Screw #10 x 5/8
02797
LATCH
HOOK
SPACER
FIG. 2
3
6
5
7
MULCH
COVER
LATCH HOOKS
4
2
7
191555 2.06.04 rad Printed in U.S.A.
www.mymowerparts.com
3
4
6
5
Loading...