Husky HSK1084HD User Manual

HSK1084HD

USER’S MANUAL

& WARRANTY INFORMATION

IIIIMMMMPPPPOOOORRRRTTTTAAAANNNNTTTTSSSSAAAAFFFFEEEETTTTYYYYIIIINNNNFFFFOOOORRRRMMMMAAAATTTTIIIIOOOONNNN,,,,SSSSAAAAVVVVEEEETTTTHHHHEEEESSSSEEEEIIIINNNNSSSSTTTTRRRRUUUUCCCCTTTTIIIIOOOONNNNSS

SS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.

4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312 U.S.

T oll Free: [phone]

8

HHHHUUUUSSSSKKKKYYYY3333YYYYEEEEAAAARRRRLLLLIIIIMMMMIIIITTTTEEEEDDDDWWWWAAAARRRRRRRRAAAANNNNTTTTYYYYPPPPRRRROOOOGGGGRRRRAAAAMM

MM

This Husky Power Product is warranted by Home Depot, to the original purchaser only, to be free of defects
in materials and workmanship for three years from the date of purchase without additional charge. If you
believe that this unit is defective during its original two-year warranty period, return the unit with proper
proof of purchase to the Home Depot store, or you may send the product to Husky Power Products at the
address below.

The warranty does not extend to subsequent purchasers or users. Husky Power Products will not be
responsible for any amount of damage in excess of the retail purchase price of the product under any
circumstances. Incidental and consequential damages are specifically excluded from coverage under this
warranty.

This product is not intended for commercial use. This warranty does not apply to accessories or damage to
units from misuse or incorrect installation/connection. Misuse includes wiring or connecting to improper
polarity power sources.

RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned to Husky Power
Products Any defective product, other than accessories, that is returned to Husky Power Products within 30
days of the date of purchase will be replaced free of charge. If such a product is returned more than 30 days
but less than three years after the purchase date, Husky Power Products will repair the unit or, at its option,
replace it free of charge.

If the unit is repaired, new or reconditioned replacement parts may be used, at Husky Power Product’s
option. A unit may be replaced with a new or reconditioned unit of the same or comparable design. The
repaired or replaced unit will then be warranted under these terms for the remainder of the warranty
period. The customer is responsible for the shipping charges on all returned items after 30 days. During the
warranty period, Husky Power Products will be responsible for the return shipping charges.

LIMITA TIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or
exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized
use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood
and Acts of God.

If your problem is not covered by this warranty, call our Technical Support Department toll free at (866) 584-

5504. for general repair information and charges, if applicable.
ST ATE LAW RIGHTS: This warranty gives the purchaser specific legal rights; other rights, which vary from

state to state, may apply. Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damages, so the exclusions or limitations stated herein
may not apply.

TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Husky Power Products Technical Support
by telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship the
unit. When returning a product, include your name, address, phone number, dated sales receipt (or copy)
and a description of the reason for return and product serial number. After repairing or replacing the unit,
we will make everyeffort to return it to you within four weeks.

W ARRANTY ACTIVA TION: Please complete Warranty Activation Card and mail to Husky Power Products.
Enter “HSK1084HD” as Model and “10/6/2 Amp Smart Batter y Charger” as Product Type. All Husky
Power Product products must be registered within 30 days of purchase to activate this warranty. Mail the
completed registration form, along with a copy of the original sales receipt to:

ATTN.: CUSTOMER SERVICE / HUSKY POWER PRODUCTS

4140 SW 28th Way, Ft. Lauderdale, FL 33312

• TOLL FREE: [phone] •

WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE

BD062805

© 2005 VECTOR MANUFACTURING

MADE IN CHINA

Fully Automatic Electronic

Smar t Batter y Charger

10/6/2 Amp Charge Rates

HSK1084HD_Manual_062805.qxd 10/21/05 7:22 PM Page 8

ii iii

Preparing to Charge

1. Determine voltage of battery to be charged by referring to the vehicle manual.

2. If it is necessary to remove battery from vehicle to charge, or to clean terminals, always remove
grounded terminal from battery first. Make sure all accessories in the vehicle are off, so as not to
cause an arc.

3. Clean battery terminals. Do not allow corrosion to come in contact with eyes.

4. Add distilled water in each cell until battery acid reaches level specified by battery manufacturer.
This helps purge excessive gas from cells. Do not overfill. For a battery without cell caps
(maintenance free), carefully follow manufacturer's charging instructions.

5. Study all battery manufacturer’s specific precautions, such as removing or not removing cell caps
while charging, and recommended rates of charge.

6. Area around battery should be well ventilated while battery is being charged. Gas can be forcefully
blown away by using a piece of cardboard or other nonmetallic material as a fan.

7. Make sure the initial charging rate does not exceed battery manufacturer’s requirement.

Charger Location

1. Locate charger as far away from battery as cables permit.

2. NEVER place charger directly above battery being charged; gases from battery will corrode and
damage charger.

3. NEVER allow battery acid to drip on charger when reading gravity or filling battery.

4. NEVER operate charger in a closed-in area or restrict ventilation in any way.

5. Marine batteries must be removed and charged on shore.

6. Do not set a battery on top of the charger.

DC Connection Precautions

1. Connect and disconnect DC output clamps only after removing AC cord from electric outlet.

2. Never allow clamps to touch each other.

3. Attach clamps to battery post and chassis as indicated in “Battery Installed in Vehicle” steps 5 and
6, and in “Battery Outside of Vehicle” steps 2, 4 and 5.

Follow these steps when the battery is installed in a vehicle to reduce risk of
sparks (which can cause an explosion):

1. Position AC and DC cords to reduce risk of damage by hood, door, or moving engine part.

2. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

3. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger diameter than
NEGATIVE (NEG, N, –) post.

4. Determine which post of battery is grounded (connected) to the chassis. If NEGATIVE post is
grounded to chassis (as in most vehicles), see 5. If POSITIVE post is grounded to the chassis, see 6.

5. For negative-grounded vehicle, connect POSITIVE (RED) clamp from battery charger to POSITIVE
(POS, P, +) ungrounded post of batter y. Connect NEGATIVE (BLACK) clamp to vehicle chassis or
engine block away from battery. Do not connect clip to carburetor, fuel lines, or sheet-metal body
parts. Connect to heavy gauge metal part of the frame or engine block.

6. For positive-grounded vehicle, connect NEGATIVE (BLACK) clamp from battery charger to
NEGATIVE (NEG, N, –) ungrounded post of battery. Connect POSITIVE (RED) clamp to vehicle
chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines or sheet­metal body parts. Connect to a heavy gauge metal part of the frame or engine block.

7. When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis, and then
remove clamp from battery terminal.

8. Do not charge the battery while the engine is operating.

9. See Operating Instructions for length of charge information.

Follow these steps when the battery has been removed from a vehicle. A
spark near the battery may cause an explosion. To reduce risk of a spark
near the battery:

1. Check polarity of battery posts. POSITIVE post (marked POS,P, +) usually has a larger diameter than
the NEGATIVE batter y post (marked NEG, N, –).

2. Attach a 24-inch (minimum length) 6 AWG insulated battery cable to the NEGATIVE battery post
(marked NEG, N, –).

3. Connect the POSITIVE (RED) battery clamp to the POSITIVE battery post (marked POS, P, + or red).

4. Stand as far back from the battery as possible, and do not face battery when making final
connection.

IMPORT ANT SAFETY INSTRUCTIONS

WARNINGS

1. RISK OF EXPLOSIVE GAS MIXTURES — WORKING IN VICINITY OF A LEAD-ACID
BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE
THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND
FOLLOW THE INSTRUCTIONS EXACTLY.

2. To reduce risk of battery explosion, follow these instructions and those published by
the battery manufacturer and manufacturer of any equipment you intend to use in
vicinity of battery. Review cautionary markings on these products and on engine.

3. This equipment employs parts (switches, relays, etc.) that produce arcs or sparks.
Therefore, if used in a garage or enclosed area, the unit MUST be placed not less
than 18 inches above the floor.

Battery Safety

1. Use of an attachment not recommended or sold by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.

2. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.

3. An extension cord should not be used unless absolutely necessary. Use of an improper extension
cord could result in a risk of fire and electric shock, and will void warranty.

If an extension cord must be used, make sure:

a. that pins on plug of extension cord are the same number, size, and shape as those of plug on

charger;
b. that extension cord is properly wired and in good electrical condition; and
c. that wire size is AWG#14 (14 gauge) for 100 feet and AWG#12 for distances over 100 feet.

4. Do not operate charger with damaged cord or plug — take to a qualified technician for
replacement of the plug or cord immediately.

5. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified service technician.

6. Do not disassemble charger; take it to a qualified service technician when service or repair is
required. Incorrect re-assembly may result in a risk of electric shock or fire, and will void warranty.

7. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or
cleaning. Turning off controls without unplugging will not reduce this risk.

8. Do not expose charger to rain, snow or use when wet.

Personal Safety

1. Another person should be within range of your voice or close enough to come to your aid when
you work near a lead-acid battery.

2. Fresh water and soap should be nearby in case battery acid contacts skin, clothing, or eyes.

3. Wear complete eye protection and clothing protection. Avoid touching eyes while working with a
battery. Acid, acid particles or corrosion may get into eyes. Immediately flood eye with cold water
(Eye Wash Station) for at least 15 minutes and seek medical attention immediately.

4. If battery acid contacts skin or clothing, wash immediately with soap and water. If redness, pain or
irritation occurs, seek immediate medical attention.

5. NEVER smoke or allow a spark or flame in vicinity of battery or engine.

6. Be extra cautious to reduce the risk of dropping a metal tool onto battery. This might cause sparks
or short-circuit the battery or other electrical part, which can cause an explosion.

7. Remove personal metal items such as rings, bracelets, necklaces and watches when working with
a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to cause a
severe burn.

8. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low­voltage electrical system other than in a starter-motor application. Do not use the battery charger
for charging dry-cell batteries that are commonly used with home appliances. These batteries may
burst and cause injury to persons and damage property.

9. NEVER ATTEMPT TO CHARGE A FROZEN BATTERY.

Power Cord Safety

This appliance has a polarized plug (one blade is wider than the other) as a safety feature. This plug will
fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

HSK1084HD_Manual_062805.qxd 10/21/05 7:22 PM Page ii