HP HCPL-2400, HCPL-2430 Datasheet

1-300

7

1

2

3

4

5

6

8

ANODE 1

CATHODE 1

CATHODE 2

ANODE 2 GND

V

CC

V

O1

V

O2

HCPL-2430

TRUTH TABLE

(POSITIVE LOGIC)

LED

ON

OFF

V

CC

GND

NC

7

1

2

3

4

5

6

8

HCPL-2400

NC

LED
ON

OFF
ON
OFF

ENABLE

L
L
H
H

OUTPUT

L
H
Z
Z

TRUTH TABLE

(POSITIVE LOGIC)

OUTPUT

L
H

V

E

V

O

ANODE

CATHODE

H

Features

• High Speed: 40 MBd Typical
Data Rate

• High Common Mode
Rejection:

HCPL-2400: 10 kV/µs at
VCM = 300 V (Typical)

• AC Performance Guaranteed
over Temperature

• High Speed AlGaAs Emitter

• Compatible with TTL, STTL,
LSTTL, and HCMOS Logic
Families

• Totem Pole and Tri State
Output (No Pull Up Resistor
Required)

• Safety Approval

UL Recognized – 2500 V rms

for 1 minute per UL1577

VDE 0884 Approved with

V

IORM

= 630 V peak (Option

060) for HCPL-2400

CSA Approved

• High Power Supply Noise
Immunity

• MIL-STD-1772 Version
Available (HCPL-5400/1 and
HCPL-5430/1)

20 MBd High CMR Logic Gate
Optocouplers

Technical Data

HCPL-2400
HCPL-2430

Applications

• Isolation of High Speed
Logic Systems

• Computer-Peripheral
Interfaces

• Switching Power Supplies

• Isolated Bus Driver
(Networking Applications)

• Ground Loop Elimination

• High Speed Disk Drive I/O

• Digital Isolation for A/D,
D/A Conversion

• Pulse Transformer
Replacement

Functional Diagram

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

Description

The HCPL-2400 and HCPL-2430
high speed optocouplers combine
an 820 nm AlGaAs light emitting
diode with a high speed
photodetector. This combination
results in very high data rate
capability and low input current.
The totem pole output (HCPL-

2430) or three state output
(HCPL-2400) eliminates the need
for a pull up resistor and allows
for direct drive of data buses.

5965-3586E

1-301

Selection Guide

8-Pin DIP (300 Mil) Minimum CMR

Single Dual Minimum Input Maximum

Channel Channel dV/dt V

CM

On Current Propagation Delay Hermetic

Package Package (V/µs) (V) (mA) (ns) Package

HCPL-2400 1000 300 4 60

HCPL-2430 1000 50 4 60

500 50 6 60 HCPL-540X*
500 50 6 60 HCPL-543X*
500 50 6 60 HCPL-643X*

*Technical data for the Hermetic HCPL-5400/01, HCPL-5430/31, and HCPL-6430/31 are on separate HP publications.

The detector has optical receiver
input stage with built-in Schmitt
trigger to provide logic compatible
waveforms, eliminating the need
for additional waveshaping. The
hysteresis provides differential
mode noise immunity and mini­mizes the potential for output
signal chatter.

The electrical and switching
characteristics of the HCPL-2400
and HCPL-2430 are guaranteed
over the temperature range of
0°C to 70°C.

These optocouplers are
compatible with TTL, STTL,
LSTTL, and HCMOS logic

families. When Schottky type TTL
devices (STTL) are used, a data
rate performance of 20 MBd over
temperature is guaranteed when
using the application circuit of
Figure 13. Typical data rates are
40 MBd.

Ordering Information

Specify Part Number followed by Option Number (if desired).
Example:
HCPL-2400#XXX

060 = VDE 0884 V

IORM

= 630 V peak Option*
300 = Gull Wing Surface Mount Option
500 = Tape and Reel Packaging Option

*For HCPL-2400 only.

Schematic

I

F

V

F

V

CC

V

O

GND

I

CC

I

O

+

–

2

3

8

5

I

F1

V

F1

V

CC

V

O1

I

CC

I

O

+

–

1

2

8

6

SHIELD

V

F2

V

O2

GND

I

O

–

+

3

4

5

I

F2

7

ANODE

CATHODE

I

E

V

E

7
6

TRUTH TABLE

(POSITIVE LOGIC)

LED

ON

OFF

LED
ON

OFF
ON
OFF

ENABLE

L
L
H
H

OUTPUT

L
H
Z
Z

TRUTH TABLE

(POSITIVE LOGIC)

OUTPUT

L
H

1-302

9.65 ± 0.25

(0.380 ± 0.010)

1.78 (0.070) MAX.

1.19 (0.047) MAX.

HP XXXXZ

YYWW

DATE CODE

1.080 ± 0.320

(0.043 ± 0.013)

2.54 ± 0.25

(0.100 ± 0.010)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

DIMENSIONS IN MILLIMETERS AND (INCHES).

5678

4321

5° TYP.

OPTION CODE*

UL
RECOGNITION

UR

0.254

+ 0.076

- 0.051

(0.010

+ 0.003)

- 0.002)

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

TYPE NUMBER

*MARKING CODE LETTER FOR OPTION NUMBERS
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.

Package Outline Drawings

8-Pin DIP Package (HCPL-2400, HCPL-2430)

8-Pin DIP Package with Gull Wing Surface Mount Option 300
(HCPL-2400, HCPL-2430)

0.635 ± 0.25

(0.025 ± 0.010)

12° NOM.

9.65 ± 0.25

(0.380 ± 0.010)

0.635 ± 0.130

(0.025 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

5

6

7

8

4

3

2

1

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

1.016 (0.040)

1.194 (0.047)

1.194 (0.047)

1.778 (0.070)

9.398 (0.370)

9.906 (0.390)

4.826

(0.190)



TYP.

0.381 (0.015)

0.635 (0.025)

PAD LOCATION (FOR REFERENCE ONLY)

1.080 ± 0.320

(0.043 ± 0.013)

4.19

(0.165)

MAX.

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.54

(0.100)

BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

0.254

+ 0.076

- 0.051

(0.010

+ 0.003)

- 0.002)

1-303

Note: Use of nonchlorine activated fluxes is highly recommended.

240

∆T = 115°C, 0.3°C/SEC

0

∆T = 100°C, 1.5°C/SEC

∆T = 145°C, 1°C/SEC

TIME – MINUTES

TEMPERATURE – °C

220
200
180
160
140
120
100

80
60
40
20

0

260

123456789101112

Solder Reflow Temperature Profile
(Gull Wing Surface Mount Option 300 Parts)

Insulation and Safety Related Specifications

Parameter Symbol Value Units Conditions

Minimum External L(101) 7.1 mm Measured from input terminals to output
Air Gap (External terminals, shortest distance through air.
Clearance)

Minimum External L(102) 7.4 mm Measured from input terminals to output
Tracking (External terminals, shortest distance path along body.
Creepage)

Minimum Internal 0.08 mm Through insulation distance, conductor to
Plastic Gap conductor, usually the direct distance between the
(Internal Clearance) photoemitter and photodetector inside the

optocoupler cavity.

Tracking Resistance CTI 200 Volts DIN IEC 112/VDE 0303 Part 1
(Comparative
Tracking Index)

Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance with CECC 00802.

Regulatory Information

The HCPL-24XX has been
approved by the following
organizations:

VDE

Approved according to VDE
0884/06.92 (Option 060 only).

UL

Recognized under UL 1577,
Component Recognition
Program, File E55361.

CSA

Approved under CSA Component
Acceptance Notice #5, File CA

88324.

1-304

VDE 0884 Insulation Related Characteristics
(HCPL-2400 OPTION 060 ONLY)

Description Symbol Characteristic Units

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤ 300 V rms I-IV
for rated mains voltage ≤ 450 V rms I-III

Climatic Classification 55/85/21
Pollution Degree (DIN VDE 0110/1.89) 2
Maximum Working Insulation Voltage V

IORM

630 V peak

Input to Output Test Voltage, Method b*

V

IORM

x 1.875 = VPR, 100% Production Test with tm = 1 sec, V

PR

1181 V peak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

V

IORM

x 1.5 = VPR, Type and sample test, V

PR

945 V peak

tm = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*
(Transient Overvoltage, t

ini

= 10 sec) V

IOTM

6000 V peak

Safety Limiting Values

(Maximum values allowed in the event of a failure,
also see Figure 12, Thermal Derating curve.)

Case Temperature T

S

175 °C

Input Current I

S,INPUT

230 mA

Output Power P

S,OUTPUT

600 mW

Insulation Resistance at TS, VIO = 500 V R

S

≥ 10

9

Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884) for a
detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must ben ensured by protective circuits
in application.