Honeywell RTH2510 User Manual 2

RTH2510
7-day Programmable Thermostat
Operating Manual
CAUTION: EQUIPMENT DAMAGE HAZARD
To prevent possible compressor damage, do not use Cooling mode when the outdoor temperature is below 50°F (10°C).
Need Help?
For assistance with this product please visit http://DIYthermostats.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502.
Read and save these instructions.
Table of contents
Overview
Thermostat features ..............................2
Quick start .............................................3
Quick reference to controls ...................4
Quick reference to display.....................5
Programming & Operation
Setting the clock....................................6
System switch (Heat/Cool)....................7
Fan switch (Auto/On).............................8
Using the schedule...........................9-11
Temporary schedule override..............12
Permanent schedule override .............13
Adaptive Intelligent Recovery (AIR) ....14
Compressor protection........................14
Programmable Thermostat RTH2510
Appendices
Battery replacement ........................... 15
In case of difficulty .............................. 16
Customer assistance .......................... 17
One-year limited warranty ..................18
Your new thermostat is pre-programmed
and ready to go!
See page 3 for quick start.
Operating Manual
About your new thermostat
Your new thermostat has been designed to give you many years of reliable service and easy-to-use, push-button climate control.
Features
Backlit display is easy to read
Displays ambient (measured) temperature at all times
One-touch access to setpoint temperature
ENERGY STAR
Separate programmable daily schedules (7-day programming)
Temporary and permanent override of schedule
Adaptive Intelligent Recovery
Built-in compressor protection
®
compliant to greatly reduce your heating/cooling expenses
TM
ensures right temperature at the right time
2
Programmable Thermostat RTH2510
This thermostat is ready to go
Simply perform the three steps below and the thermostat is in operation:
n Set the clock ................................................................................................ See page 6
o Select whether to heat or cool...................................................................... See page 7
p Select whether to run the fan continuously or only when needed................ See page 8
Your thermostat is pre-programmed with ENERGY STAR® settings. If you do not wish to use these settings, you can:
Modify the schedule ....................................................................................See page 11
Temporarily override the schedule ............................................................. See page 12
Permanently override the schedule............................................................ See page 13
3
Operating Manual
Quick reference to controls
Press to set clock, day or schedule (see pages 6 & 11).
Press to override schedule and hold temperature (see page 13).
Press to run (follow) schedule (see page 9).
Screen
Lit for 12 seconds when you press any button.
4
Up/Down buttons Press to adjust temperature.
System switch (see page 7)
Cool: System is in Cooling mode.
Off: System is off.
Heat: System is in Heating mode.
Fan switch (see page 8)
On: Fan runs continuously.
Auto: Fan runs only when
heating or cooling is activated.
Programmable Thermostat RTH2510
Quick reference to display
Setpoint indicator
Appears when the setpoint temperature is displayed.
Clock
Schedule period
System status
Cool On: Cooling is activated. *
Heat On: Heating is activated. *
Aux On: Auxiliary heat is activated.
* When Heat On or Cool On is flashing, compressor protection is engaged (see page 14).
Temporary schedule override
(see page 12)
Low-battery warning (see page 15)
Permanent schedule override
(see page 13)
Temperature
The ambient (measured) temperature is normally displayed. To view the setpoint temperature, press the Up or Down button once. The setpoint temperature will appear for five seconds.
5
Operating Manual
Set the clock
n Press the Set button. Set Time will appear on the screen and the
time display will flash.
o Press the Up or Down button to set the time. p Press the Set button again. Set Day will flash on the screen. q Press the Up or Down button to select the day of the week. r Press the Run button to save the changes & exit. (The changes
are also saved if you do not press any button for 60 seconds.)
NOTE: The clock has lost its settings when the time display flashes. If the thermostat is following the schedule, it will use the temperature settings programmed for the Wake period for Monday until you readjust the clock.
6
System switch (Heat/Cool)
CAUTION: EQUIPMENT DAMAGE HAZARD.
Do not use Cooling mode when the outdoor temperature is below 50°F (10°C).
Programmable Thermostat RTH2510
Use the System switch to place the system in one of the following modes:
Cool: System is in Cooling mode.
Off: System is off.
Heat: System is in Heating mode.
7
Operating Manual
Fan switch (Auto/On)
Use the Fan switch to select the fan operation.
Auto: The fan runs only when heating or
cooling is activated (commonly used setting).
On: The fan runs continuously.
8
Programmable Thermostat RTH2510
Using the schedule
Press the Run button to follow the programmed schedule. For maximum energy savings while maintaining comfort, you can program the schedule such that the temperature is at an economical level when you sleep or leave for work and at a comfortable level when you are awake and at home. You can program up to four periods per day:
Wake Starts when you wake up Leave Starts when you leave for work Return Starts when you return home Sleep Starts when you go to sleep
To program a period, you need to set its start time and its two temperature settings (one when the thermostat is in cooling mode and another one when it is in heating mode). You can set a different program for each day of the week.
9
Operating Manual
Energy Star® settings
The thermostat has been programmed with the ENERGY STAR® settings for each day of the week (see table below). See next page if you wish to modify the settings.
Period Start time Heat Cool
Wake 6:00 AM 70°F (21°C) 78°F (25.5°C)
Leave 8:00 AM 62°F (16.5°C) 85°F (29.5°C)
Return 6:00 PM 70°F (21°C) 78°F (25.5°C)
Sleep 10:00 PM 62°F (16.5°C) 82°F (27.5°C)
10
Programmable Thermostat RTH2510
Modifying the schedule
n Press the Set button 3 times until Set Schedule appears. The Wake period is
displayed.
NOTE: To set another period, press the Set button as many times as needed until the desired period and the desired day are displayed and its time or temperature is flashing.
o When the time flashes, press the Up or Down button to set the time. p Press the Set button. q To set the temperature for cooling mode, first place the System switch in Cool. To
set the temperature for heating mode, first place the System switch in Heat.
r When the temperature flashes, press the Up or Down button to set the temperature. s Press the Set button. t Repeat steps 2 through 6 to set each of the remaining periods. u Once all changes are made, press the Run button to save them and return to
normal display. (The changes will automatically be saved if you do not press any button for 60 seconds.)
11
Wake period for Monday is set to 6 a.m. and 70°F
To skip a period (except Wake), press the Hold button for 4 seconds while that period is displayed.
Operating Manual
Temporary override of schedule
To temporarily ignore the schedule, press the Up or Down button until the desired temperature is displayed.
The word Tempo rary will appear on the screen and the period display will flash to indicate that the current period has been overridden. The new temperature will be used until the next period begins.
NOTE: Pressing the Up or Down button once will display the setpoint temperature. To change the setpoint temperature, press either button more than once.
Press the Run button if you wish to cancel the temporary setting before the beginning of the next period.
12
Loading...
+ 30 hidden pages