Honeywell R295HP-F Product specification sheet

Mechanical disconnector hydraulic actuated
GB type according to EN
The mechanical disconnectors comprises:
• Housing with pressure gauge
• Outlet differential pressure transducer
• Spring bonnet
• PN 16 flanged connections to ISO 7005-2, DIN EN 1092-2
• Hydraulically controlled changeover valve
• Drain connector
• Valve insert with spring
• Spindle guide with double O-ring seal
Materials
• Grey cast iron housing, powder coated inside and outside
• Steel spring bonnet
• Elastic, ageing and scuff resistant elastomer seals
• Stainless steel valve stem and spring
• Red bronze for other internal parts
• Red bronze drain connector up to DN 100, Grey cast iron drain connector DN 125 - DN 200, powder coated inside and outside
• Chrome plated balanced-seat piston
EN0H-1212GE23 R0206 y Subject to change without notice
• High grade synthetic material bearing surfaces for sliding in­ternal parts
1717/ type 2 according to DIN1988 part 4
R295HP-F
Product specification sheet
Application
Mechanical disconnectors of this type are suitable for the protec­tion of drinking water systems as required by EN 1717 "The tech­nical regulation of drinking water systems" and correspond to DIN1988 part 4 type 2 construction.
Their purpose is to protect systems against back pressure, back flow and back syphonage of non-potable water into the public water supply network.
Mechanical disconnectors of this type can be used to provide protection up to and including liquid category 4 (toxic, very toxic, carcinogenic and radioactive substances).
Special Features
• DIN/DVGW and SVGW approvals in all connection sizes
• Optimal protection of the drinking water supply system
• Enhanced protection against back pressure, back flow and back syphonage into the water supply network
• Shutoff position visually indicated on the spring bonnet
• Compact construction
• Powder coated inside and outside - Powder used is physio­logically and toxicologically safe
• Meets KTW recommendations for potable water
•Low pressure loss
Range of Application
Medium Cold water
Max. inlet pressure 16.0 bar
Technical Data
Installation position Horizontal with spring bonnet upwards
Max. operating temperature
Opening pressure 0.5 bar
Minimum inlet pres­sure
Minimum flow rate 1.0 l/min
Connection size DN 65 - 200
40°C
1.5 bar
www.honeywell.com 41
R295HP-F Mechanical disconnector hydraulic actuated
Method of Operation
Type 2 mechanical disconnectors are normally in the shutoff po­sition. When water is drawn from the downstream system, the differential pressure in the mechanical disconnectors rises. If the differential pressure rises above 0.5 bar, the hydraulic operator causes the control valve to change the mechanical disconnec­tors into the flow position. When the draw-off stops, the differen­tial pressure then falls again and the pressure sensor transmits a signal to the control valve, which then returns the mechanical dis­connectors to the normal shutoff position.
Options
R295HP-... FA = With flanges, differential pressure 0.5 bar ope-
ning pressure
Special Versions available on request
Connection size
Connection size DN 65 80 100 125 150 200 Weight approx. kg 49 68 90 146 207 409 Dimensions mm
L 532 572 652 752 882 1102
H 380 495 475 528 563 851
h 165 208 232 280 313 438
Nominal flow rate m
3
/h at p = 0.8 bar 21 31 45 89 134 222 kvs-value (full flow) 24 35 50 100 150 248 ξ value 50.0 53.5 64.0 39.0 36.0 42.0 DIN/DVGW Approval No. NW - 6301 AT 2323
42 www.honeywell.com
EN0H-1212GE23 R0206 y Subject to change without notice
Loading...
+ 2 hidden pages