The Galaxy 16 and 16 plus control panels are designed to the highest specifications and
requirements using the most advanced software and hardware technology.
The Galaxy 16 and 16 plus are designed to satisfy the requirements of domestic and smaller
commercial installations, yet are flexible enough to provide ease of use and operational versatility.
This User’s Guide contains the information required to operate the system. The installation
engineer will program and commission the system to meet your requirements. The system is
simple to operate but users are advised to read this guide carefully before using the system
and retain it in a safe place for future reference.
v
vi
QUICK OPERATION GUIDE
ASET (an Unset system)
BPART SET (Defaults to Parts 1 and 2)
e ntUNSET (a Set system)
1OMIT ZONES
2CHIME ZONES
3WALK TEST
Enter your user
code then select
4(ASSIGNING) USER CODES
5TEST OUTPUTS
9LOG
ent+B TIME
1 key • toggles the Set (ON)/Unset (OFF) status of Part 1
2 key • toggles the Set (ON)/Unset (OFF) status of Part 2
3 key • toggles the Set (ON)/Unset (OFF) status of Part 3
A or B key to view zones
# to change omit status of zone (must be an omittable zone)
ent key to accept programming and start setting
esc key to accept programming without setting
A or B key to view zones
# key to enable/disable chime function on zone
ent key to accept
esc key to cancel
A or B key to view zones
# key to enable/disable Walk Test function on zone
ent key to start Walk Test
# key to toggle display between open and tested zones
esc key to end Walk Test
Note: Zones number 10 to 16 will be displayed as A to G
A or B key to select user (1 – 14)
ent key to program code
number keys to enter digits, ¸ key to delete digits
ent key to accept programming, esc to cancel
A or B key to select output for test
# key to enable/disable test function on zone
esc key to end test
A key to step forwards through events
B key to step backwards through events
# key to display event date
esc key to exit Log
To access the Time option, enter your user code, press the ent key,
the B key and then the ent key.
Then press the:
•1 key to select Time (hh/mm)
•2 key to select Date (dd/mm/yy)
•3 key to select Start Summer (dd/mm)
•4 key to select End Summer (dd/mm).
Press the ent key to accept the programming for each option,
or the esc key to cancel.
vii
viii
GLOSSARY OF TERMS
Chime:Zone attribute which gives an audible indication of the activation of a detector
or contact.
Duress:Applicable when a remote signalling device is fitted. A Duress code entered at
the keypad will unset the system but transmit a Duress code to the Alarm
Receiving Centre.
Entry Time:The preset time allowed for users to reach the keypad and unset the system.
Exit Time:The preset time allowed for users to leave the building after the setting routine
has been initiated.
Exit Terminator:A switch or push-button located outside the protected area and used to set the
system.
Event Log:The control panel memory which stores, in sequence, a record of the system
events.
Final Exit:The last door closed or detector operated by the user on exit.
LCDLiquid Crystal Display.
Non–omit:An alarm circuit which cannot be omitted (bypassed) by the user.
Numeric Keypad:The unit comprising the LCD display and buttons that is the interface between
users and the system.
Omit:Setting the system with alarm zones excluded from the system. Only zones
programmed as “omittable” by the engineer can be omitted.
PAPanic Alarm: an emergency button or switch used to set off the alarm; results
in instantaneous transmission of a silent alarm signal using the remote signalling device.
Part Set:To set only a section of the full system.
Programme:To alter the system functions or parameters.
Set:To arm the system.
Unset:To disarm the system.
User Code:A four digit code that identifies users to the system.
Walk Test:A routine test of the alarm detectors.
Security Circuit:An alarm circuit which has been programmed to be armed continuously
whether the system is set or not.
ix
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.