Honeywell CMR707A1049 User Manual
CMR707A1049 - User Guide
OFFMANAUTO
1 2 3 4 5 6 7
CMR707 - USER GUIDE
Features
• Ergonomic user interface featuring an ‘OK-button’.
• Large LCD (Liquid Crystal Display) Screen.
• 7-day heating program to match your lifestyle, whilst
maximising energy savings.
• 4 independent temperature levels per day (from 5°C to
35°C).
• Holiday button saves energy by letting you reduce the
temperature for 1 to 99 days.
• Built-in Memory holds the user program indefinitely.
Description
The Honeywell CMR707 is a
programmable room thermostat
designed to control your heating
system efficiently, providing
comfortable temperatures when
you are at home and energy
savings when you are away. The
following instructions explain
how to set up, program and
operate your Honeywell CMR707
Programmable Room Thermostat.
Controls Layout
LCD Screen
Battery Low Indicator
Time Display
Heating Required Indicator
Day Indicator
Temperature Display
1
2
3
4
5
6
Holiday Function Button
Program Buttons
Copy Day Button
Day Select Button
Time Change Buttons
Temperature Change Buttons
Temperature Enquiry Button
Operating Mode Buttons
Green OK Button
Battery Compartment
Battery Cover
7
8
9
10
11
12
13
14
15
16
17
COPY
DAY
DAY
..4
OFFMANAUTO
1 2 3 4 5 6 7
AUTO
MAN
OFF
16
15
17
1 2 43 5
8
9
10
7
12
13
14
11
6
PROGRAM
CM707
SETTING-UP THE CMR707 ‘Getting Started’
This section shows you how to setup and run the thermostat in 3 simple steps:
STEP 1: Installing the Batteries
Note: if the ‘Low Battery’ Indicator is showing or the thermostat screen is blank (no symbols
or digits are displayed) replace the batteries as follows, otherwise, please go directly to Step 2:
Setting the Date and Time.
To install the Batteries:
a. Lift up the front cover of the thermostat to reveal the battery cover and product controls.
b. Remove the battery cover by pressing down and sliding out.
c. Inser t the 2 x AA LR6 Alkaline Batteries supplied with the thermostat, ensuring the correct
orientation (see ‘Controls Layout’ on page 2).
d.
After a short pause the thermostat will display information on the screen and is now ready for use.
e. Replace the batter y cover by sliding it firmly back into the front of the thermostat.
STEP 2: Setting the Day and Time
To set the Day and Time:
a. Press the DAY button once and the ‘day indicator’ will begin to flash.
b. Press the DAY button until the correct day is reached (Day 1 = Monday). Press the green
button to confirm.
d. Press either of the or buttons once to enter time setting mode. The LCD screen flashes
the time digits (when the unit is powered for the first time the display shows 12:00).
e. Use the or buttons to set the correct time then press the green button to confirm.
Each press of the buttons will change the time by one minute and holding them down will
change the time slowly at first and get progressively quicker.
Note: If this mode is entered accidentally then press the AUTO, MAN or OFF buttons to exit.
STEP 3: Running the Built-in Heating Program
The thermostat is now ready for operation. Press the AUTO button and the built-in heating program will start
running. Note: The built-in heating program has been designed to provide normal comfort requirements,
but if you want to customise the settings please see the next section ‘Programming the CMR707’.
PROGRAMMING THE CMR707 ‘Efficient Daily Use’
The Built-in Heating Program
The built-in heating program has 4 temperature level changes per day that can be set between
3.00am and 2.50am the following day - allowing you to maintain the evening temperature after
midnight. Each temperature level can be set between 5°C and 35°C, and adjusted in 0.5°C
increments. The factory default program for heating is as follows.
Period 1 2 3 4
Time 6:30 8:00 18:00 22:30
Temperature 21°C 18°C 21°C 16°C
Period 1 2 3 4
Time 8:00 10:00 18:00 23:00
Temperature 21°C 21°C 21°C 16°C
PLEASE RESPECT YOUR ENVIRONMENT! Take care to dispose of used batteries carefully.
Monday to Friday
(Day 1 to 5)
Saturday & Sunday
(Day 6 & 7)
Loading...