Honeywell 6110GP User Manual
™
Dolphin
with Windows® Embedded Handheld 6.5
User’s Guide
6110 Mobile Computer
1
/
6
1
/
9
t
f
a
r
D
3
Disclaimer
Preliminary 2013-09-16
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to
determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights are reserved.
No part of this document may be photocopied, reproduced, or translated into another language without
the prior written consent of HII.
Web Address: www.honeywellaidc.com
Trademarks
Dolphin is a trademark or registered trademarks of Hand Held Products, Inc. or Honeywell International
Inc.
Microsoft, Windows, Windows Mobile, Windows Embedded Handheld, Windows CE, Windows NT,
Windows 2000, Windows ME, Windows XP, ActiveSync, Outlook, and the Windows logo are trademarks
or registered trademarks of Microsoft Corporation.
Other product names mentioned in this manual may be trademarks or registered trademarks of their
respective companies and are the property of their respective owners.
Other Trademarks
The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell
International Inc.
Patents
For patent information, please refer to www.honeywellaidc.com/patents.
©2013 Honeywell International Inc. All rights reserved.
Table of Contents
Preliminary 2013-09-16
Chapter 1 - Agency Approvals
Label Locations....................................................................................................................1-1
N4313-TTL Safety & RF Approvals by Country: ..................................................................1-1
Dolphin RF Terminal—802.11a/b/g/n and/or Bluetooth .......................................................1-2
Chapter 2 - Getting Started
Out of the Box ......................................................................................................................2-1
Initial Setup for Dolphin 6110 Terminals ..............................................................................2-1
LED Indicators................................................................................................................2-2
Home Screen .......................................................................................................................2-4
Title Bar................................................................................................................................2-4
Horizontal Scroll...................................................................................................................2-5
Horizontal Scroll...................................................................................................................2-6
Tile Bar.................................................................................................................................2-6
Pop-Up Menus .....................................................................................................................2-6
Selecting Programs..............................................................................................................2-6
File Explorer.........................................................................................................................2-7
File Provisioning on the Dolphin 6110 .................................................................................2-8
Search..................................................................................................................................2-8
Turning Power On/Off ..........................................................................................................2-9
Suspend Mode ...............................................................................................................2-9
Resetting the Terminal.........................................................................................................2-9
Chapter 3 - Hardware Overview
Standard Terminal Configurations .......................................................................................3-1
Dolphin Peripherals/Accessories for the Dolphin 6110........................................................3-1
USB Communication Cable for the Dolphin 6110................................................................3-2
Front Panel Features ...........................................................................................................3-2
Using the Touch Panel.........................................................................................................3-3
Installing a Screen Protector ..........................................................................................3-4
Back Panel Features............................................................................................................3-4
Left Side Panel Features .....................................................................................................3-5
Right Side Panel Features ...................................................................................................3-6
Top Panel Features .............................................................................................................3-6
Bottom Panel Features ........................................................................................................3-7
Battery Power ......................................................................................................................3-7
Battery Pack...................................................................................................................3-8
Managing Battery Power................................................................................................3-9
Storage Guidelines.........................................................................................................3-9
Hardware Maintenance......................................................................................................3-10
Installing Memory Cards ..............................................................................................3-10
Dolphin 6110 Technical Specifications ..............................................................................3-12
iii
Chapter 4 - Using the Keypad
Preliminary 2013-09-16
Overview.............................................................................................................................. 4-1
Navigation Keys................................................................................................................... 4-1
Basic Keys........................................................................................................................... 4-1
Alpha/Numeric Modes ......................................................................................................... 4-2
Alpha Indicators on the Number Keys ........................................................................... 4-2
Function Key Combinations................................................................................................. 4-2
CTRL Key Combinations ..................................................................................................... 4-3
Program Buttons.................................................................................................................. 4-3
Chapter 5 - Using the Image Engine
Overview.............................................................................................................................. 5-1
Available Image Engines ..................................................................................................... 5-1
Depth of Field ................................................................................................................5-1
Supported Bar Code Symbologies ..................................................................................... 5-2
Activating the Engine...........................................................................................................5-3
Capturing Images (56XX Engine only) ................................................................................ 5-3
Chapter 6 - Using the Laser Engine
Overview.............................................................................................................................. 6-1
Available Laser Engines ...................................................................................................... 6-1
Depth of Field - N4313-TTL........................................................................................... 6-1
Supported Bar Code Symbologies ..................................................................................... 6-1
Activating the Engine...........................................................................................................6-2
Decoding a Bar Code .......................................................................................................... 6-2
Chapter 7 - System Settings
Overview.............................................................................................................................. 7-1
Clock & Alarms .................................................................................................................... 7-2
Personal Menu ....................................................................................................................7-3
Buttons........................................................................................................................... 7-3
Program Buttons............................................................................................................ 7-5
System Menu....................................................................................................................... 7-8
About .............................................................................................................................7-9
Backlight ........................................................................................................................ 7-9
Certificates................................................................................................................... 7-10
Encryption.................................................................................................................... 7-11
HSM SystemInfo.......................................................................................................... 7-11
Error Reporting ............................................................................................................ 7-12
Managed Programs ..................................................................................................... 7-12
Memory........................................................................................................................ 7-12
Power...........................................................................................................................7-14
Regional Settings......................................................................................................... 7-16
Remove Programs....................................................................................................... 7-16
Screen ............................................................................................................................... 7-18
SIP Configuration .............................................................................................................. 7-19
iv
Task Manager....................................................................................................................7-20
Preliminary 2013-09-16
Chapter 8 - Communication
Connecting the Dolphin 6110-USB Communication Cable ................................................. 8-1
Charging Terminal with USB Cable..................................................................................... 8-1
Connections Menu............................................................................................................... 8-3
Receiving Data .................................................................................................................... 8-3
Connections Manager ......................................................................................................... 8-4
To Access the Connections Manager............................................................................ 8-4
Tasks ............................................................................................................................. 8-5
Advanced....................................................................................................................... 8-6
Dolphin Wireless Manager .................................................................................................. 8-7
Dolphin Wireless Manager Window............................................................................... 8-7
Enabling the Radios....................................................................................................... 8-8
Accessing Radio Configuration Utilities......................................................................... 8-8
Network Cards..................................................................................................................... 8-9
Connecting and Synchronizing the Terminal and Workstation............................................ 8-9
Installing Additional Software ............................................................................................ 8-12
Adding Programs Using ActiveSync or Windows Mobile Device Center..................... 8-12
Connecting the Terminal to a Wireless Network.......................................................... 8-13
Adding Programs Using the Internet............................................................................ 8-13
Software Upgrades............................................................................................................ 8-14
Chapter 9 - Working with the Bluetooth Radio
Enabling the Bluetooth Radio .............................................................................................. 9-1
Pairing and Trusted Devices ............................................................................................... 9-2
Connecting to Other Bluetooth Devices .............................................................................. 9-2
Transferring Files................................................................................................................. 9-4
Making the Terminal Discoverable ...................................................................................... 9-6
Chapter 10 - Dolphin HomeBase (Model 6100-HB)/eBase
(Model 6100-EHB) Device
Overview............................................................................................................................ 10-1
Front Panel ....................................................................................................................... 10-2
Back Panel .......................................................................................................................10-3
Powering the Dolphin HomeBase Device.......................................................................... 10-4
eBase Clamp-on Ferrite Core Installation ......................................................................... 10-4
Charging the Battery.......................................................................................................... 10-5
Charging a Spare Battery ............................................................................................ 10-6
Checking Battery Power .................................................................................................... 10-6
Technical Specifications .................................................................................................... 10-7
Chapter 12 - Dolphin 6110 Net Base Device (Model 6100-NB)
Overview............................................................................................................................ 12-1
v
Parts and Functions........................................................................................................... 12-2
Preliminary 2013-09-16
Front Panel .................................................................................................................. 12-2
Back Panel .................................................................................................................. 12-3
Bottom Panel ............................................................................................................... 12-4
Power ................................................................................................................................ 12-4
Connecting Power to the Net Base.............................................................................. 12-4
Charging the Battery.......................................................................................................... 12-5
To Power a Terminal and Charge its Battery............................................................... 12-5
Communication.................................................................................................................. 12-5
Software Requirements ............................................................................................... 12-5
Connecting the Dolphin Terminal to the Net Base ............................................................ 12-5
Mounting the Net Base ...................................................................................................... 12-6
Chapter 13 - Dolphin QuadCharger Device
Overview............................................................................................................................ 13-1
QuadCharger Device ........................................................................................................ 13-1
Battery Charging................................................................................................................ 13-2
Recommendations for Storing Batteries............................................................................ 13-3
Troubleshooting................................................................................................................. 13-3
Technical Specifications .................................................................................................... 13-4
Chapter 13 - Customer Support
Technical Assistance......................................................................................................... 13-1
Product Service and Repair............................................................................................... 13-1
Limited Warranty ...............................................................................................................13-1
Limited Warranty Duration................................................................................................. 13-2
How to Extend Your Warranty ..................................................................................... 13-2
vi
1
Compliance Label
Laser Light Label
Preliminary 2013-09-16
Agency Approvals
Label Locations
Dolphin 6110 mobile computers meet or exceed the requirements of all applicable standards
organizations for safe operation. However, as with any electrical equipment, the best way to ensure safe
operation is to operate them according to the agency guidelines that follow. Read these guidelines
carefully before using your mobile computer.
Laser Safety Label
If the following label is attached to your product, it indicates that the product contains an engine with a
laser aimer:
LASER LIGHT. DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
1.0 mW MAX OUTPUT: 650nM
IEC60825-1: 1993+A1+A2
Complies with 21 CFR 1040.10 and 1040.11
except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007.
N4313-TTL Safety & RF Approvals by Country:
Country Safety RF (Radio)
U.S.A. UL60950-1 FCC Part 15, Sub part B, Sub
part C
Canada* C-UL CSA C22.2 No. 60950-1-07 ICES-003, RSS 210
European
Community
IEC 60825-1:2007
IEC62471:2006
EN609501:2006+A11:2009+A1:2010+A12:2011
EN55022 (CISPR 22) Class B
EN55024:2010
EN300 328
EN301 489-1
EN301 489-7
EN301 489-17
IEC 62209-2
* Does not apply to N4313-TTL laser engine.
1 - 1
• Consult the dealer or an experienced radio/TV technician for help.
!
Preliminary 2013-09-16
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions. The user may find the following booklet helpful: “Something About Interference.”
This is available at FCC local regional offices. Our company is not responsible for any radio or television
interference caused by unauthorized modifications of this equipment or the substitution or attachment of
connecting cables and equipment other than those specified by our company. The correction is the
responsibility of the user. Use only shielded data cables with this system.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter. To maintain compliance with FCC RF exposure guidelines for bodyworn operation, do not use accessories that contain metallic components.
CAUTION! Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.
Canadian Compliance
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and
away from windows to provide maximum shielding. Equipment (or its transmit antenna) installed outdoors
is subject to licensing.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
For European Community Users
Honeywell Scanning & Mobility Product Environmental Information
Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information.
1 - 3
1 - 4
Preliminary 2013-09-16
2
Cover Locks
Battery
Preliminary 2013-09-16
Getting Started
Out of the Box
Verify that your carton contains the following items:
• Dolphin 6110 mobile computer (the terminal)
• Battery pack (3.7v, Li-Ion)
• AC power supply
• Localized plug adapters
Note: Be sure to keep the original packaging in case you need to return the Dolphin terminal for service; see
Customer Support on page 13-1.
Initial Setup for Dolphin 6110 Terminals
Step 1. Install the Battery
The Dolphin 6110 is shipped with the battery packaged separate from the unit. Follow the steps below to
install the battery.
1. Release the strap making it convenient to reach the cover.
(KSAS0100500200D5; Input: 100-240V AC, 50/60Hz 0.4 Amps; Output: 5 Volts DC, 2.0 A)
2. Remove the battery compartment cover by turning the cover locks upward and removing the cover.
3. Insert the battery into the battery well with the labels facing upward.
4. Replace the cover with a hinging motion and turn the locks downwards.
Note: The battery door must be installed prior to booting the unit.
5. Replace the hand strap.
2 - 1
We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result in damage not
!
Dolphin 6110s ship with the battery pack
significantly discharged of power. Charge the
battery pack with the Dolphin charging cable until
the LED turns green (red while charging). The
average charge time for a fully depleted battery is
7 1/2 hours. It takes less time if the battery has
some charge.
1. Attach the appropriate plug adapter to the
plug of the power cable.*
2. Insert the plug into the appropriate power
source.
3. Plug the Dolphin power cable into the DC
Power Jack (see page 3-7) on the bottom end
of the unit.
Important:
Removing the battery from the terminal erases
all non-persistent memory.
LED Indicators
*This power cable can also be used to power the
Dolphin 6110 while in the Dolphin HomeBase
(Model 6100-HB)/eBase (Model 6100-EHB)
Device (see page 10-1).
Red LED On
Charging
Green LED On
Battery is fully charged
1
2
3
!
!
!
Preliminary 2013-09-16
covered by the warranty.
Step 2. Charge the Batteries
We recommend use of Honeywell peripherals, power cables, and power adapters compiled with
L.P.S. Use of any non-Honeywell peripherals, cables, or power adapters may cause damage not
covered by the warranty.
Ensure all components are dry prior to mating terminals/batteries with peripheral devices. Mating
wet components may cause damage not covered by the warranty.
2 - 2
The power adapter on the power cable converts the voltage from the power source to 5 volts DC. Only
Power Adapte r
Plug Adapter
Power Cable
Preliminary 2013-09-16
power adapter cables from Honeywell convert the voltage appropriately. The power cable contains a plug
adapter for each geography (US, UK, EU, etc.).
Step 3. Boot the Terminal
The terminal is not connected to an external power source, it begins booting once you push the Power
button. If the terminal is connected to an external power source (e.g., power cable, HomeBase), it will
automatically reboot. Do NOT press any keys or interrupt the boot process.
When the boot process is complete, the Desktop appears, and the terminal is ready for use.
Step 4. Set the Time Zone, Time, and Date
On the Home screen, tap the line that displays the
time and date.
When the Clock & Alarms screen appears, tap the arrow to the right of the time zone to open the drop
down menu. Select the appropriate time zone from the menu. Set the correct time and date in the
remaining fields and tap OK to save.
2 - 3
Home Screen
Text here indicates
the active program.
Icons here indicate the
status of various system
functions.
Preliminary 2013-09-16
After the Dolphin terminal initializes the first time, you see the Home screen.
Tap to reach the Start screen from the home screen.
Tap to access the Dolphin Wireless Manager Window (see page 8-7) from the home screen.
Title Bar
The Title bar, located at the top of the screen, displays the active program, the status of various system
functions, and the current time. Tapping on the title bar provides access to the Horizontal Scroll. The
scroll provides access to additional programs and application screens. For additional information, see
Horizontal Scroll on page 2-5.
2 - 4
Horizontal Scroll
Preliminary 2013-09-16
Indicator Meaning
Synchronizing data
The terminal could not synchronize data with the workstation via ActiveSync.
New e-mail
New text message
New voicemail
New instant message
Ringer off
A battery error has occurred. Replace the battery pack with a Honeywell Li-poly or Li-ion battery
pack.
Battery is has a full charge
Battery has a high charge
Battery has a medium charge
Battery has a low charge
Battery has a very low charge and requires charging
Terminal is running on external power. If a battery pack is installed, the battery is charging in the
background.
The terminal is not connected to external power. A battery is installed, but is defective; specifically,
its charge level cannot be measured.
Active network connection
No active network connection
Wi-Fi is on, but device is not connected
Wi-Fi data call
Pending alarm
Bluetooth
2 - 5
Horizontal Scroll
The content of the
Horizontal scroll
changes according to
the open application.
The icons change according to the open application.
The Task tray displays icons
for programs running in the
background.
The Tile bar displays icons you
use to open and close screens,
menus, and features.
Preliminary 2013-09-16
The Horizontal Scroll, located at the top of most application windows, provides access to additional
application screens. You can flick left or right on the scroll or tap each label on the scroll, until you get to
the desired screen. Tapping a label to the left or right of the center item brings new labels into view.
Note: Tap the Title bar to access the horizontal scroll if it is not visible on the screen.
Tile Bar
The Tile bar is located at the bottom of application windows.
Pop-Up Menus
With pop-up menus, you can quickly choose an action for a selected item. To access a pop-up menu, tap
and hold the stylus on the item name of the action you want to perform. When the menu appears, lift the
stylus, and tap the action you want to perform.
Ta p OK to close the menu without performing an action.
Selecting Programs
To see the programs loaded on your terminal, tap to access the Start Menu. To open a
program, tap once on the program icon. To reposition an icon on the Start Menu, tap and hold the stylus
on the icon, then drag the icon to the desired position.
2 - 6
File Explorer
Preliminary 2013-09-16
You can also use the File Explorer to find files and organize these files into folders.
1. Tap > File Explorer .
2. Tap the Up button at the bottom of the screen to move up one level in the directory.
3. You can move files in File Explorer by tapping and holding on the item you want to move, then
tapping Cut or Copy on popup menu.
4. Navigate to the folder you want to move the file to, then tap and hold a blank area of the window.
5. Tap Paste on the pop-up menu.
Note: If there is no blank space available in the window, tap
menu using the down arrow, then tap
Edit > Paste
.
Menu
on the command bar, navigate to the end of the
2 - 7
File Provisioning on the Dolphin 6110
!
!
Preliminary 2013-09-16
\IPSM\Honeywell
The IPSM folder is the only partition on the terminal that persists across a kernel upgrade (*.UPG file
extension). During a kernel upgrade, files are automatically copied from the \IPSM\Honeywell folder
and then installed in the \Honeywell (root file system) folder as part of the upgrade process.
\IPSM\Honeywell\AutoInstall
The files in the IPSM\Honeywell\AutoInstall folder are only installed when a factory reset or
kernel upgrade occurs. Once the files are installed, they persist through hard and soft resets. If a file is
added to the folder and a hard or soft reset is performed, it will have no effect. If a program is manually
removed using the Remove Programs application (see page 7-16), then the program is not automatically
re-installed on a hard or soft reset.
\Honeywell
The Honeywell partition or root file system partition is persistent over a hard reset, soft reset, and the
removal of the battery pack or the removal of AC power. However, during a kernel upgrade or factory
reset, the root file system is reformatted so all data in the folder is deleted and replaced by any files in
the \IPSM\Honeywell folder as part of the upgrade process.
To prevent data loss, back up all user data to an SD card or external memory device before performing an
upgrade or factory reset.
\Honeywell\AutoInstall
If you run a CAB file from within the \Honeywell\AutoInstall folder, after the program has been
installed, the CAB file will be deleted. However, the program remains installed through all successive
hard and soft resets.
If you want the program to be part of the Autoinstall that occurs after a factory reset or software upgrade,
paste the program file(s) into the \IPSM\Honeywell\Autoinstall folder.
Contact a Honeywell technical support representative for information on how to perform a factory reset
or for information on available software upgrades for your Dolphin terminal. For contact information, see
Product Service and Repair on page 13-1.
Note:To prevent data loss, back up all user data to an SD card or external memory device before
performing an upgrade.
Search
The Search feature helps you quickly locate information. Tap > Search Phone .
Enter the text you want to find, select a data type, and then tap Search. Select Larger than 64 KB in the
Type drop-down field to quickly find information that is taking up storage space.
2 - 8
Turning Power On/Off
Preliminary 2013-09-16
To turn the terminal On, press the Power button .
To turn the terminal Off:
1. Press and hold the Power button for approximately 4 seconds until the options menu displays.
2. Tap Power off.
Suspend Mode
Suspend mode differs from Power off mode. Power off mode is the equivalent to having no battery or
external power source connected to the device. In Suspend mode, the device enters a low power state
to conserve battery power.
Suspend mode automatically turns the system off, which includes turning the screen off to save battery
power when the terminal is inactive for a programmed period of time. The automatic timeout limits are
adjustable from the Advance tab located under Settings > System > Power (see page 7-14). In
addition, Suspend mode also automatically turns off the radio and drivers. The PMIC and main
processor wakeup mode clock remain on allowing the system to detect a wakeup interrupt and to
resume working.
Press and release the Power button to toggle the terminal in or out of Suspend mode.
Note: You should always place the terminal in Suspend mode before removing the battery.
Resetting the Terminal
There are three types of system resets: a Soft Reset, a Hard Reset, or a Factory Reset. The soft and
hard resets preserve all data stored in the file system. Contact a Honeywell technical support representative for more information on how to perform a Factory Reset. For contact information, see Technical
Assistance on page 13-1.
A Soft Reset (Warm Boot) re-boots the device and preserves any objects created in RAM. You would
perform a soft reset when: the terminal fails to respond, after installing some software applications, or
after making changes to certain system settings, such as network cards.
A Hard Reset (Cold Boot) re-boots the terminal and closes any open applications running in RAM at the
time of the reset.
To perform a Soft Reset or Hard Reset:
1. Press and hold the Power button until the options menu appears.
2. Tap Soft Reset or Hard Reset on the menu.
3. When the reset is complete, the Home screen displays.
Note: To perform a Hard Reset if the screen has stopped responding, press and hold the Power button for
approximately 8 seconds until the terminal starts to re-boot. When the reset is complete, the Home screen
displays.
2 - 9
2 - 10
Preliminary 2013-09-16
3
Preliminary 2013-09-16
Hardware Overview
Standard Terminal Configurations
Dolphin 6110 WPAN/WLAN
• Microsoft Windows Embedded Handheld 6.5
Classic
• TI OMAP37xx 800MHz
• 512 MB RAM X 512 MB Flash Memory
• 28-key shifted alpha numeric keypad
• 240x320. 262.144 Color Transmissive TFT
Display
• Standard Capacity: Li-ion battery: 3.7V /
2200mAh / 8.1 Wh or Extended Capacity: Li-ion
battery: 3.7V / 3300mAh / 12.2 Wh
• 56XX image engine with laser aiming or N4313TTL laser engine
• (WPAN/WLAN) - Bluetooth and 802.11a/b/g/n
radio
• Dolphin power cable (included with each
Dolphin 6110)
Dolphin Peripherals/Accessories for the Dolphin 6110
The following items are sold separately and enhance your Dolphin 6110’s capabilities.
Dolphin HomeBase™ Device
This charging and communication cradle supports USB and RS-232 communication, enabling your
terminal to interface with the majority of enterprise systems. When a terminal is seated in a powered base,
its battery pack charges in an average of 7 1/2 hours for a fully depleted battery. It takes less time if the
battery has some charge.
This device also contains an auxiliary battery well that charges a spare battery.
For more information, see Dolphin HomeBase (Model 6100-HB)/eBase (Model 6100-EHB) Device on
page 10-1.
Dolphin eBase™ Device
The Dolphin eBase is used to charge the battery and can be used to communicate data from the terminal
to a PC/laptop via the Ethernet port.
This device also contains an auxiliary battery well that charges a spare battery.
For more information, see Dolphin HomeBase (Model 6100-HB)/eBase (Model 6100-EHB) Device on
page 10-1.
Dolphin QuadCharger™ Device
The Dolphin QuadCharger device, a four-slot charging station for Dolphin Li-Ion battery packs, can
charge each battery in an average of 7 1/2 hours for a fully depleted battery. It takes less time if the
battery has some charge.
For more information, see Dolphin QuadCharger Device on page 13-1.
3 - 1
Dolphin NetBase Device
LED
Touch Screen
Display (screen
protector
installed at the
factory)
Keypad (28-key
shifted alpha
numeric)
Navigation
keys
Scan key
Power key
Software
Reset key
Preliminary 2013-09-16
The Dolphin NetBase device, enables up to four Dolphin 6110 mobile computers to communicate with a
host device over an Ethernet network.
For more information, see Dolphin 6110 Net Base Device (Model 6100-NB) on page 12-1.
USB Communication Cable for the Dolphin 6110
The USB Communication Cable for the 6110 is used when communicating between the terminal and a
PC/laptop via the USB port. The cup-style 6110-USB cable slides onto the bottom of the device lining up
with the connector. The cable unit includes an opening for the power cable. See Connecting the Dolphin
6110-USB Communication Cable (page 8-1).
Li-Ion Battery Packs
The Li-Ion battery pack provides the main power supply for the terminal. For more information, see Battery
Power on page 3-7.
For information on how to purchase these items, contact a Honeywell sales representative.
Front Panel Features
Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all
Dolphin 6110 models unless otherwise indicated.
3 - 2
Scan/Decode LED
!
!
Preliminary 2013-09-16
Note: The LED is user-programmable.
LED color Description
Red While battery is charging.
Once Scan button pressed in scanning applications.
Green When battery charging is complete.
Scanned bar code is successfully decoded.
Blue or Red Soft or hard resets.
Scan Key
The SCAN key is centrally located for easy access with the right or left hand. When pressed,
the SCAN key activates the scanner/imager. The SCAN key also functions as a system
wakeup control for the terminal.
Keypad
A 28-key shifted alpha numeric keypad is included on the unit.
Microphone
The integrated microphone can be used for audio recording.
Touch Screen Display
The display is a LCD (Liquid Crystal Display) with a 4-wire analog resistive touch screen. The
2.8” (1/4) VGA (Video Graphic Array) is transmissive active matrix color, backlit, and the
resolution is 240 x 320; see Backlight on page 7-9. The touch panel is a 4-wire analog resistive
touch.
Dolphin 6110s ship with a screen protector already installed over the touch screen lens
to help prevent damage to the touch screen. Do NOT remove this screen protector before
initial use. Honeywell recommends using screen protectors, especially for applications
that require high volume interfacing with the touch screen. You can purchase additional
screen protectors by contacting your Honeywell sales representative.
For touch screen input, use the stylus included with the terminal or your finger. The method
you choose depends on which one is most appropriate for your application. While there is a
great deal of variation in different applications, you generally achieve greater accuracy with the
stylus for buttons or icons that are close together.
Use of objects, such as paper clips, pencils, or ink pens on the touch screen can damage
the input panel and may cause damage not covered by the warranty.
Using the Touch Panel
Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus.
Screen protectors maintain the ongoing integrity (i.e., prevent scratching) of the touch panel, which is
why their use is recommended for applications that require a high-to-medium level of interface with the
touch panel, such as signature capture for proof of delivery.
Honeywell advocates the use of screen protectors on all Dolphin devices. We recommend implementing
3 - 3
a screen protector replacement program to ensure that screen protectors are replaced periodically when
Engine Window
Speaker
Installed Battery
Finger
Saddle
Hand Strap (with Stylus)
Preliminary 2013-09-16
signs of damage/wear are noticeable. Replacement screen protectors can be purchased directly from
Honeywell. Please contact a Honeywell sales associate for details.
Honeywell also mandates use of a proper stylus, which is one that has a stylus tip radius of no less than
0.8 mm. Use of the Honeywell stylus included with the terminal is recommended at all times.
Honeywell warranty policy covers wear on the touch panel for the first twelve (12) months if a screen
protector is applied and an approved stylus is used for the 12 month duration covered by the warranty.
Installing a Screen Protector
Dolphin terminals ship with a screen protector already installed. You will need to replace the screen
protector at regular intervals.
1. After the current screen protector has been removed from the touch panel, clean the touch panel
thoroughly with a clean, non-abrasive, lint-free cloth. Make sure there is no debris on the touch
panel.
2. Align the exposed section of the protector with the left edge of the touch panel. Make sure that the
screen protector is flush with each side of the touch panel. To reposition, lift up gently and reapply.
3. Press the screen protector firmly and carefully across the surface of the touch panel as you peel
away the backing.
4. If necessary, smooth out any air pockets or bumps.
Back Panel Features
Note: Your Dolphin model may differ from the model illustrated; however, the features noted are standard for all
Dolphin 6110 models unless otherwise indicated.
Hand Strap
The Dolphin 6110 comes with an adjustable, elastic hand strap. The strap is attached to the
device with the two small screws. It is threaded through the slot on the bottom of the back of
the unit.
3 - 4
Keep in mind that the hand strap covers the battery. When you want to replace the battery, you
Side Button
Micro SD Slot
Preliminary 2013-09-16
will need to adjust the hand strap accordingly.
Finger Saddle
This is a slightly depressed and angled area of the back housing that is designed to cradle or
“saddle” your finger while holding the terminal. This unique ergonomic design makes the
terminal comfortable to hold and helps prevent you from accidentally dropping the terminal.
Installed Battery
For information about installing the battery, see Changing the Battery Pack on page 3-8
For information about battery power, see Battery Power on page 3-7.
Speaker
The integrated speaker sounds audio signals as you scan bar code labels and enter data, but
emits no ambient noise on system activity (i.e., processor, memory access, radio traffic, etc.).
The speaker can also be used for playing sounds (e.g., WAV or MP3 files).
The speaker meets the following SPL levels at 40cm:
• 500Hz–67db
• 1KHz–72db
• 4KHz–72db
Stylus
Dolphin 6110 terminals ship with a stylus inserted in a loop on the hand strap. The stylus is used to
operate the touch panel. The stylus features a special tip for added accuracy and ease of use. Store the
stylus in the hand strap when you’re not using it.
Left Side Panel Features
Side Button
There is a side button on both side panels. You can use the Program Buttons option to change
the functionality of the side buttons. Tap > System > Settings > Program Buttons.
Side Door
The rubber door on the left side panel provides access to the Micro SD slot.
When closed, the side door seals the terminal from moisture and particle intrusion thus
preserving the terminal’s environmental rating.
3 - 5
Right Side Panel Features
Side Button
Headset
Jack
Imager or Laser Aperture Window
Preliminary 2013-09-16
Headset Jack
The rubber door on the right side panel provides access to the headset jack. This is a 3.5mm
audio jack that supports a headset with a mono speaker and microphone.
When closed, the side door seals the terminal from moisture and particle intrusion thus
preserving the terminal’s environmental rating.
Side Button
There is a side button on both side panels. You can use the Program Buttons option to change
the functionality of the side buttons. Tap > System > Settings > Program Buttons.
Top Panel Features
Imager or Laser Aperture Window
The angled image engine or laser engine reads and decodes most popular bar code
symbologies and takes images like a digital camera (image engine only). For more
information, see Using the Image Engine on page 5-1 or see Using the Laser Engine on page
6-1.
3 - 6
Bottom Panel Features
DC Power Jack
I/O Connector
Preliminary 2013-09-16
DC Power Jack
The DC power jack receives external power from the Dolphin power cable that is included in
the box with the terminal. When connected to the Dolphin power cable, the terminal is powered
and the battery pack is charging.
I/O Connector
The I/O mechanical connector is designed to work exclusively with Dolphin 6110 peripherals
and cables. This connector powers the terminal, charges the battery, and facilitates
communication. The I/O connector supports high speed USB 2.0 communication (up to 480
Mbps) and RS-232 communications with a maximum speed of 115Kbps and seven baud rate
settings.
Through this connector, you can communicate with a host workstation via Microsoft
ActiveSync; see Connecting and Synchronizing the Terminal and Workstation on page 8-9
The I/O connector supports the following signals:
• DC IN
• Transmitted Data
• Request To Send
• USB Host +5V
• USB Host D+
• USB Host D-
• USB Host Detect
• Clear To Send
• Received Data
•GND
• RS-232 Shutdown
• USB Client D+
• USB Client D-
• USB Client +5V
Note: Signals referenced are for a DTE device.
Battery Power
The battery pack is located on the back panel (see Battery Pack on page 3-8)
3 - 7
The battery must be charged to full capacity before using the Dolphin 6110 for the first time!
!
Cover Locks
Battery
Preliminary 2013-09-16
Charge the battery pack with the Dolphin USB Charging/Communication cable until the LED turns green
(red while charging). The average charge time for a fully depleted battery is 7 1/2 hours. It takes less
time if the battery has some charge.
Battery Pack
Caution: We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may result
in damage not covered by the warranty.
There are two Li-ion battery packs available for the 6110:
Standard Capacity: Li-ion 3.7V/2200mAh/8.1Wh
Extended Capacity: Li-ion 3.7V/3300mAh/12.2Wh
Changing the Battery Pack
Before installing a battery pack, press the Power button to put the terminal into Suspend Mode (see page
2-9) so that operations are suspended before removing the power source. The Dolphin 6110 is shipped
with the battery separate from the unit. You will need to loosen the hand strap, remove the battery door,
insert the battery, and replace the battery door. Refer to the instructions included in "Install the Battery" on
page 2-1 section.
Note: The battery door must be installed prior to booting the unit.
Charging Options
Dolphin terminals ship with the battery significantly discharged of power. Before using a Dolphin terminal
for the first time, charge the battery with a Dolphin charging device for a minimum of 6 hours for the
standard battery and 9 hours for the extended battery. When the battery is installed in the terminal, you
can use any of the peripherals listed below to charge the battery.
• Dolphin HomeBase (Model 6100-HB)/eBase (Model 6100-EHB) Device (see page 10-1)
• Dolphin Comm/Charge Cable; Managing Battery Power (see page 3-9). You may charge the device
using the USB connection if you do not have a wall adapter. Access the option by selecting >
Settings > System > Power > USB Charging (see see Charging Terminal with USB Cable on page
8-1).
To fully charge the Li-Ion battery before installing it in the terminal, use the
• QuadCharger Device (see page 13-1) or insert the battery in the spare battery charging well in the back
of either the Dolphin HomeBase or Dolphin eBase.
3 - 8
Charging Time
Preliminary 2013-09-16
The standard capacity 2200mAh Li-ion battery pack requires 6 hours to charge to full capacity, while the
extended capacity 3300mAh pack requires 9 hours. It takes less time if the battery has some charge.
Managing Battery Power
Data and files saved on the Dolphin terminal may be stored in RAM memory; therefore, maintain a
continuous power supply to the terminal to help prevent data loss. When you remove a battery pack, insert
another charged battery pack in the Dolphin. If the battery pack is low, insert the terminal into a charging
peripheral to power the terminal and begin recharging the battery.
Note: If you remove the battery pack or it completely discharges, all data in RAM is cleared. Always place the
terminal in Suspend mode before removing the battery to ensure that any changes made are saved to the
flash memory.
Note: If the battery is low and the terminal is in Suspend Mode, pressing the
Dolphin 6110 terminal; you must first replace the discharged battery with a fully charged battery or apply A/C
power to the terminal.
Power button does
not
wake the
Checking Battery Power
Power icons appear in the title bar at the top of the window. Tap on the battery icon to open the Power
Properties or select > Settings > System > Power. The Battery screen opens displaying the charge
status of the battery.
Storage Guidelines
To maintain optimal battery performance, follow these storage guidelines:
• Avoid storing batteries outside the specified range of -4 to 140° F (-20 to 40°C) or in extremely high
humidity.
• For prolonged storage, it is recommended that the battery be at a 40% - 50% charge level, be removed
from the device, and stored in a controlled temperature environment. Following these
recommendations will maximize battery life.
Guidelines for Battery Pack Use and Disposal
The following are general guidelines for the safe use and disposal of batteries:
• Do not disassemble or open crush, bend or deform, puncture or shred.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose
to water or other liquids, expose to fire, explosion or other hazard.
3 - 9
• Improper battery use may result in a fire, explosion or other hazard.
Preliminary 2013-09-16
• We recommend use of Honeywell Li-Ion battery packs. Use of any non-Honeywell battery may pose a
personal hazard to the user.
• Only use the battery for the system for which it is specified. Do not use a battery in any other manner
outside its intended use in Dolphin terminals and peripherals.
• Ensure all components are dry prior to mating batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
• Replace defective batteries immediately; using a defective battery could damage the Dolphin terminal.
• Never throw a used battery in the trash. Promptly dispose of used batteries in accordance with local
regulations.
• Do not short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury. Do
not allow metallic conductive objects to contact battery terminals.
• Don’t use a battery in any other manner outside its intended use in Dolphin terminals and peripherals.
• Don’t short-circuit a battery or throw it into a fire; it can explode and cause severe personal injury.
• Excessive discharge damages a battery. Recharge the battery when your terminal indicates low battery
power.
• If you observe that the Honeywell battery supplied is physically damaged in some way, send it to
Honeywell International Inc. or an authorized service center for inspection, see Product Service and
Repair on page 13-1
• Avoid dropping the terminal or battery. If the terminal or battery is dropped, especially on a hard
surface, and the user suspects damage, send it to a Honeywell International Inc. or an authorized
service center for inspection, see Product Service and Repair on page 13-1.
• Although your battery can be recharged many times, it will eventually be depleted. Replace it after the
battery is unable to hold an adequate charge.
• If you are not sure the battery or charger is working properly, send it to Honeywell International or an
authorized service center for inspection.
Charging
You can begin using the Dolphin terminal after charging the battery for an average of 7 1/2 hours for a
fully depleted battery. It takes less time to charge the battery if the battery has some charge.
Hardware Maintenance
When needed, clean the image/laser aperture window and the LCD display with a clean, non-abrasive,
lint-free cloth. The terminal can be cleaned with a damp cloth.
Installing Memory Cards
Note: Honeywell recommends the use of Single Level Cell (SLC) industrial grade microSD or microSDHC memory
cards with Dolphin terminals for maximum performance and durability. Only memory cards purchased directly
from Honeywell are supported. Contact a Honeywell sales representative for additional information on
qualified memory card options.
To install an SD card:
1. Open the access door on the left side.
2. Insert the SD card with the label facing upward.
Note: To remove an installed SD card while the access door is open, tap on the edge lightly to unlock the card; the
card pops out just enough for you to grab its edge and to pull it out.
3. Replace the access door.
3 - 10
Loading...