Honda HS1332SAWJ Owner's Manual
Owner,s Manual
Click to Save As
SNOWBLOWER
HS928・HS1332
C
Honda Motor Co., Ltd. -All Rights Reserved
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Keep this owner’s manual handy, so you can refer to it any time. This
owner’s manual is considered a permanent part of the snowblower
and should remain with the snowblower if resold.
The information and specifications included in this publication were in
effect at the time of approval for printing. Honda Motor Co., Ltd.
reserves the right, however, to discontinue or change specifications or
design at any time without notice and without incurring any obligation
whatever.
INTRODUCTION
Congratulations on your selection of a Honda snowblower. We are
certain you will be pleased with your purchase of one of the finest
snowblowers on the market.
We want to help you get the best results from your new snowblower
and to operate it safely. This manual contains the information on how
to do that; please read it carefully.
As you read this manual, you will find information preceded by a
symbol. That information is intended to help you avoid
damage to your snowblower, other property, or the environment.
We suggest you read the warranty policy to fully understand its
coverage and your responsibilities of ownership. The warranty policy
is a separate document that should have been given to you by your
dealer.
When your snowblower needs scheduled maintenance, keep in mind
that your Honda servicing dealer is specially trained in servicing
Honda snowblowers. Your Honda servicing dealer is dedicated to your
satisfaction and will be pleased to answer your questions and
concerns.
Best Wishes,
Honda Motor Co., Ltd.
1
INTRODUCTION
A FEW WORDS ABOUT SAFETY
Your safety and the safety of others are very important. And using this
snowblower safely is an important responsibility.
To help you make informed decisions about safety, we have provided
operating procedures and other information on labels and in this
manual. This information alerts you to potential hazards that could
hurt you or others.
Of course, it is not practical or possible to warn you about all the
hazards associated with operating or maintaining a snowblower. You
must use your own good judgment.
You will find important safety information in a variety of forms,
including:
Safety Labels
Safety Messages
of three signal words, DANGER, WARNING, or CAUTION.
These signal words mean:
Safety Headings
Safety Section
Instructions
This entire book is filled with important safety information please
read it carefully.
−
on the snowblower.
−
preceded by a safety alert symbol and one
You WILL KILLED SERIOUSLY HURT
you don’t follow instructions.
You CAN KILLED SERIOUSLY HURT
you don’t follow instructions.
You CAN HURT
instructions.
−
such as
such as
−
how to use this snowblower correctly and safely.
−
SNOWBLOWER SAFETY
be or if
be or if
be if you don’t follow
IMPORTANT SAFETY INFORMATION
.
−
.
2
CONTENTS
............................................................................................CONTROLS .11
.........................................................................................Fuel Gauge .11
.......................................................................................Chute Crank .12
........................................................................................Starter Grip .12
.......................................................................................Choke Knob .13
..........................................................................................Shift Lever .13
..........................................................................................Foot Pedal .14
.............................................................................................FEATURES .17
.........................................................................................Work Light .17
..............................................................................................OPERATION .21
...............................................................................................TOOL KIT .36
...........................................................................................REFUELING .39
...........................................................................SNOWBLOWER SAFETY .5
..................................................IMPORTANT SAFETY INFORMATION .5
.................................................................SAFETY LABEL LOCATIONS .8
..........................................................................CONTROLS & FEATURES .9
.............................................COMPONENT & CONTROL LOCATIONS .9
................................................................................Fuel Valve Lever .11
....................................................................................Engine Switch .11
....................................................................................Throttle Lever .12
................................................................Discharge Deflector Lever .14
....................................Drive Clutch Lever and Auger Clutch Lever .15
............................................................Transmission Release Lever .16
............................................................................Snow Clearing Bar .17
...............................................................................BEFORE OPERATION .18
................................................ARE YOU READY TO GET STARTED? .18
.........................................IS YOUR SNOWBLOWER READY TO GO? .18
..........................Check the General Condition of the Snowblower .19
...............................................................................Check the Engine .19
.................................................................CHECK YOUR WORK AREA .20
.......................................................SNOWBLOWING PRECAUTIONS .21
......................................................................STARTING THE ENGINE .21
......................................................................STOPPING THE ENGINE .26
.................................................................................CLEARING SNOW .29
........................................................................SNOW-CLEARING TIPS .32
..............................................................REMOVING OBSTRUCTIONS .33
........................................................SERVICING YOUR SNOWBLOWER .34
.............................................THE IMPORTANCE OF MAINTENANCE .34
......................................................................MAINTENANCE SAFETY .35
................................................................MAINTENANCE SCHEDULE .37
...............................................................FUEL RECOMMENDATIONS .40
3
CONTENTS
SERVICING YOUR SNOWBLOWER (continued)
..................................................................ENGINE OIL LEVEL CHECK .41
...........................................................................ENGINE OIL CHANGE .42
....................................................ENGINE OIL RECOMMENDATIONS .43
.............................................HYDROSTATIC TRANSMISSION FLUID .44
.........................................................................SPARK PLUG SERVICE .46
.........................................................................TRACK ADJUSTMENT .48
.................................................................................TIRE INSPECTION .49
..................................................AUGER AND BLOWER INSPECTION .49
.........................................LOCK BOLT REPLACEMENT PROCEDURE .50
...............................................................SKID SHOES AND SCRAPER .51
..................................................................................................STORAGE .53
....................................................................STORAGE PREPARATION .53
.............................................................................................Cleaning .53
.....................................................................................................Fuel .54
..........................................................................................Engine Oil .57
....................................................................................................Tires .57
...................................................................STORAGE PRECAUTIONS .58
................................................................REMOVAL FROM STORAGE .58
......................................................................................TRANSPORTING .59
................................................................................BEFORE LOADING .59
...............................................................................................LOADING .60
.......................................TAKING CARE OF UNEXPECTED PROBLEMS .62
.............................................................................ENGINE PROBLEMS .62
..............................................................................DRIVER PROBLEMS .64
...............................................................SNOWBLOWER PROBLEMS .65
....................................................................TECHNICAL INFORMATION .67
..................................................................Serial Number Locations .67
............................................Emission Control System Information .69
.............................................................................................Air Index .71
....................................................................................Specifications .72
...................................................................CONSUMER INFORMATION .74
.........................................................................Honda PUBLICATIONS .74
.........................................................Customer Service Information .75
.............................QUICK REFERENCE INFORMATION .Inside back cover
....................Carburetor Modification for High Altitude Operation .68
4
SNOWBLOWER SAFETY
IMPORTANT SAFETY INFORMATION
Honda snowblowers are designed to clear snow from driveways and
walkways. Other uses can result in injury to the operator or damage to
the snowblower and other property.
Most injuries or property damage with snowblowers can be prevented
if you follow all instructions in this manual and on the snowblower.
The most common hazards, are discussed below, along with the best
way to protect yourself and others.
Avoid Rotating Impeller and Auger
Hand contact with the rotating impeller inside the discharge chute is
the most common cause of injury associated with snowblowers. The
snowblower auger can also cause serious injury. Keep away from the
impeller and auger whenever the engine is running. If you need to
work around the snowblower to clear snow for any reason, always
shut off the engine. If the snow discharge chute becomes clogged,
stop the engine and disconnect the spark plug cap. Use the snow
clearing bar or a wooden stick to remove the obstructions. Never put
your hand into the snow discharge chute while the engine is running;
serious personal injury could result.
Clear Operation Area
The snowblower can throw rocks and other objects with enough force
to cause serious injury. Before operating the snowblower, carefully
inspect the area and remove any visible stones, sticks, bones, nails,
pieces of wire, and other loose objects. Never use the snowblower to
clear snow from a gravel road or driveway, as rocks may be picked up
and ejected. They may cause injury to bystanders.
5
SNOWBLOWER SAFETY
Keep Shields in Place
Guards and shields are designed to protect you from being hit by
thrown objects and to keep you from touching hot engine parts and
moving components. For your safety and the safety of others, keep all
shields in place when the engine is running.
Adjust the snow discharge chute to avoid hitting the operator,
bystanders, windows, and other objects with ejected snow. Stay clear
of the snow discharge chute while the engine is running.
Children and pets must be kept away from the area of operation to
avoid injury from flying debris and contact with the snowblower.
Refuel with Care
Gasoline is extremely flammable, and gasoline vapor can explode.
Allow the engine to cool if the snowblower has been in operation.
Refuel only outdoors in a well-ventilated area with the engine OFF. Do
not overfill the fuel tank. Never smoke near gasoline, and keep other
flames and sparks away. Always store gasoline in an approved
container. Make sure that any spilled fuel has been wiped up before
starting the engine.
Turn Engine OFF When Not Operating the Snowblower
If you need to leave the snowblower for any reason, even just to
inspect the area ahead, always turn the engine off.
Operation on Slopes
To avoid overturning, be careful when changing the direction of the
snowblower while operating it on a slope. Do not use the snowblower
to remove snow from roofs. The snowblower may overturn on steep
slopes if left unattended, causing injury to the operator or bystanders.
6
SNOWBLOWER SAFETY
Operating Conditions
Do not use the snowblower when visibility is poor. Under conditions
of poor visibility, there is a greater risk of striking an obstacle or
causing injury. Adjust the snow discharge chute to avoid hitting
bystanders or vehicles.
Stay clear of the snow discharge chute while the engine is running and
be aware that loose clothing can get drawn into the moving parts.
Operating Near Roads
Always watch for vehicle traffic when operating the snowblower near
roads and driveways.
Operator Responsibility
Know how to stop the snowblower quickly in case of emergency.
Understand the use of all snowblower controls.
Never permit anyone to operate the snowblower without proper
instruction. Do not let children operate the snowblower. If people or
pets suddenly appear in front of the snowblower while it is in
operation, immediately release the auger and drive clutch levers to
stop the snowblower and avoid possible injury from rotating auger
blades.
While operating the snowblower, hold the handle firmly and walk,
don’t run. Wear suitable winter boots that resist slipping.
Wear safety glasses or eye shields during operation to protect eyes
from thrown objects.
Exercise caution on slippery surfaces to avoid falling, especially when
operating in reverse.
7
SNOWBLOWER SAFETY
SAFETY LABEL LOCATIONS
These labels warn you of potential hazards that can cause serious
injury. Read them carefully.
If a label comes off or becomes hard to read, contact your Honda
snowblower dealer for a replacement.
8
CONTROLS & FEATURES
COMPONENT & CONTROL LOCATIONS
Use the two illustrations on these pages to locate and identify the
most frequently used controls.
Track type
DISCHARGE DEFLECTOR
WORK LIGHT
SNOW DISCHARGE
CHUTE
DISCHARGE DEFLECTOR LEVER
AUGER CLUTCH LEVER
FUEL TANK CAP
AUGER
FUEL VALVE
STARTER GRIP
THROTTLE LEVER
DRIVE CLUTCH
LEVER
SHIFT LEVER
MUFFLER
TRACK
AC STARTER BUTTON
(TAS type)
SNOW CLEARING BAR
CHOKE KNOB
ENGINE SWITCH
TRANSMISSION
FLUID RESERVOIR
CHUTE CRANK
FOOT PEDAL
FRAME SERIAL
NUMBER
TRANSMISSION
RELEASE LEVER
ENGINE SERIAL
NUMBER
ENGINE OIL
FILLER CAP
SKID SHOE
9
CONTROLS & FEATURES
Wheel type
DISCHARGE DEFLECTOR
WORK LIGHT
SNOW DISCHARGE
CHUTE
DISCHARGE DEFLECTOR LEVER
AUGER CLUTCH LEVER
FUEL TANK CAP
AUGER
FUEL VALVE
STARTER GRIP
THROTTLE LEVER
SHIFT LEVER
DRIVE CLUTCH
LEVER
MUFFLER
WHEEL
AC STARTER BUTTON
(WAS type)
CHOKE KNOB
ENGINE SWITCH
TRANSMISSION
FLUID RESERVOIR
CHUTE CRANK
FRAME SERIAL NUMBER
TRANSMISSION RELEASE LEVER
10
SNOW CLEARING BAR
SKID SHOE
ENGINE SERIAL NUMBER
ENGINE OIL
FILLER CAP
CONTROLS
CONTROLS & FEATURES
Fuel Valve Lever
The fuel valve opens and closes
the fuel line leading from the fuel
tank to the carburetor. Make sure
that the fuel valve is positioned
exactly at either the ON or OFF
position. When the snowblower is
not in use, always leave the fuel
valve in the OFF position to
reduce the possibility of fuel
leakage.
Engine Switch
The engine switch controls the
ignition system. The key can only
be inserted and removed when
turned to OFF.
−
OFF Stops the engine.
−
ON Running position, and for
starting with the recoil starter.
EL VALVE LEVER
FU
OFF
ON
ENGINE SWITCH
OOFFFF
OONN
Fuel Gauge
The fuel gauge indicates the
amount of fuel in the tank. When
the fuel gauge needle enters the
EMPTY position, refill the tank as
soon as possible.
FUE
L GAUGE
FULL
EMPTY
11
CONTROLS & FEATURES
Chute Crank
Use the chute crank to turn the snow discharge chute right or left.
To throw snow to the right
CHUTE CRANK
To throw snow to the left
ARTER GRIP
Starter Grip
Pull this grip to start the engine.
See page for starting
24
procedures.
ST
Throttle Lever
The throttle lever controls engine
speed from SLOW to FAST, it will
stay in any designated position.
SLOW
THROTTLE LEVER
12
FFAASSTT
CONTROLS & FEATURES
Choke Knob
The choke knob opens and closes the choke valve in the carburetor.
The CLOSED position enriches the fuel mixture for starting a cold
engine.
The OPEN position provides the correct fuel mixture for operation
after starting, and for restarting a warm engine.
OPEN
CLOSED
CHOKE KNOB
Shift Lever
The shift lever selects F (FORWARD), N (NEUTRAL), or R (REVERSE).
The shift lever also controls the transmission drive ratio; moving the
lever farther from NEUTRAL increases drive speed. While clearing
snow, use the shift lever to control drive speed, so you can leave the
throttle lever in the FAST position for best snow-clearing performance.
N (Neutral)
R (Reverse)
SHIFT LEVER
F (Forward)
13
CONTROLS & FEATURES
Discharge Deflector Lever
The discharge deflector lever controls the snow discharge angle.
DISCHARGE DEFLECTOR
HIGH AND FAR
LOW AND NEAR
HIGH AND FAR
DISCHARGE DEFLECTOR LEVER
LOW AND NEAR
Foot Pedal (track type only)
Use the pedal for adjusting the height and angle of the machine in
relation to the tracks.
Hold the handles and step on the pedal.
Raise or lower the machine to the desired position and release the
pedal.
LOW Smooth, ice-covered surfaces only.
−
MIDDLE Normal use.
HIGH Deep snow or for transporting the snowblower.
−
−
14
FOOT PEDAL
HIGH
MIDDLE
LOW
CONTROLS & FEATURES
Drive Clutch Lever and Auger Clutch Lever
Use these controls to engage the snow blowing mechanism and/or the
drive mechanism.
DRIVE CLUTCH LEVER
Squeeze to engage the
drive transmission.
AUGER CLUTCH LEVER
Squeeze to engage the
snow blowing mechanism.
When both levers are squeezed, the drive clutch lever locks the auger
clutch lever down. Releasing the drive clutch lever then unlocks and
releases the auger clutch lever.
DRIVE CLUTCH LEVER
LLOOCCKKEEDD
The auger clutch lever
Both levers squeezed
remains locked down as
long as one hand continues
to squeeze the drive clutch lever.
15
CONTROLS & FEATURES
Transmission Release Lever
The transmission release lever has two positions, RELEASED and
ENGAGED. Set the lever to the ENGAGED position for self-propelled
operation. Set it to the RELEASED position when pushing the
snowblower with the engine stopped.
Operating the transmission release lever while the engine is running
can damage the transmission.
Stop the engine.
1.
Set the shift lever to the ‘‘N’’ (Neutral) position.
2.
Set the lever to the ENGAGED or RELEASED position.
3.
Pushing or towing the snowblower with the transmission release
control in the engaged position will damage the hydrostatic
transmission.
16
RREELLEEAASSEEDD EENNGGAAGGEEDD
TRANSMISSION RELEASE LEVER
FEATURES
CONTROLS & FEATURES
Work Light
The light comes ON while the
engine is running, and it goes OFF
when the engine stops. The light
does not come ON when the
engine switch is turned ON unless
the engine is started. The light can
be adjusted up or down.
Snow Clearing Bar
If the snow discharge chute or
snow blowing mechanism
becomes restricted, stop the
engine, and make sure all rotating
parts have come to a complete
stop. Remove the spark plug cap
from the spark plug.
WORK LIGHT
UUPP
DDOOWWNN
SNOW CLEARING BAR
Use the snow clearing bar to
remove the obstruction.
After clearing the obstruction,
wipe the bar clean, and store it in
the holders. Replace the spark
plug cap.
HOLDERS
17
BEFORE OPERATION
ARE YOU READY TO GET STARTED?
Your safety is your responsibility. A little time spent in preparation will
significantly reduce the risk of injury.
Knowledge
Read and understand this manual. Know what the controls do and
how to operate them.
Familiarize yourself with the snowblower and its operation before you
begin using it. Know how to quickly shut off the snowblower in case of
an emergency.
IS YOUR SNOWBLOWER READY TO GO?
For your safety, and to maximize the service life of your equipment, it
is very important to take a few moments before you operate the
snowblower to check its condition. Be sure to take care of any problem
you find, or have your servicing dealer correct it, before you operate
the snowblower.
Improperly maintaining this
snowblower, or failing to correct a
problem before operation, could
cause a malfunction in which you
could be seriously injured.
Always perform a pre-operation
inspection before each operation,
and correct any problem.
Before beginning your pre-operation checks, be sure the snowblower
is on a level surface and the engine switch is in the OFF position.
18
BEFORE OPERATION
Check the General Condition of the Snowblower:
Look around and underneath the snowblower for signs of oil or
gasoline leaks.
Check the auger housing and the discharge chute for accumulation
of packed snow or ice. Clean the auger housing and discharge chute
before starting the snowblower.
Look for signs of damage.
Check each control for proper operation.
Check the auger and blower for loose or broken bolts. If broken,
replace them with new ones (see page ).
Check the skid shoes and scraper for wear. Replace them if
necessary (see page ).
Check that all nuts, bolts, and screws are tightened.
Check the Engine
51
50
Check the oil level (see page ).
Check the fuel level (see page ). Starting with a full tank will help
to eliminate or reduce operating interruptions for refueling.
Check the hydrostatic fluid level in the reservoir (see page ). Use
only Honda Hydrostatic Fluid.
41
39
44
19
BEFORE OPERATION
CHECK YOUR WORK AREA
For your safety and the safety of others, always inspect the area before
operating the snowblower.
Objects
Anything that can be picked up by the augers and thrown is a potential
hazard to you and others. Thoroughly inspect the area where the
equipment is to be used and remove all doormats, sleds, boards, wires,
stones, and nails from the work area.
People and Pets
People and animals near the work area can move into your
snowblower’s path or into a position where they could be struck by
thrown objects. Clear the area of people, especially children, and pets.
Their safety is your responsibility.
Work Area
Check the condition of the snow. Adjust your snowblower ground
speed (not engine speed) and snowblowing swath accordingly.
Check the skid shoes for proper adjustment. Adjust the skid shoes to
obtain the auger ground clearance for the type of surface the
snowblower will be operated over (see page ).
52
20
OPERATION
SNOWBLOWING PRECAUTIONS
Before operating the snowblower for the first time, please review both
SNOWBLOWER SAFETY
the
OPERATION
Even if you have operated other snowblowers, take time to become
familiar with how this snowblower works, and practice in a safe area
until you build up your skills.
Never tamper with or alter any of the controls or safety devices on the
snowblower. Tampering is a violation of Federal and California law.
For your safety, do not start or operate the engine in an enclosed area
such as a garage. Your snowblower’s exhaust contains poisonous
carbon monoxide gas that can collect rapidly in an enclosed area and
cause illness or death.
chapter (see page ).
Exhaust contains poisonous carbon
monoxide gas that can build up to
dangerous levels in closed areas.
Breathing carbon monoxide can
cause unconsciousness or death.
chapter (see page ) and the
18
5
BEFORE
Never run the engine in a closed, or
even partly closed area where
people may be present.
STARTING THE ENGINE
Move the shift lever to ‘‘N’’ (Neutral) position.
1.
N (Neutral)
SHIFT LEVER
21
OPERATION
Set the transmission release
2.
lever in the ENGAGED position
(see page ).
Turn the fuel valve to the ON
3.
position. Be sure that the drain
knob is tightened securely.
16
EENNGGAAGGEEDD
TRANSMISSION RELEASE LEVER
ON
22
DRAIN KNOB
EL VALVE LEVER
FU
Loading...