OWNERS MANUAL
PROPANE
CONSTRUCTION
HEATER
Model HP35
Indicates Warning,
Danger, and Caution
!
!
GENERAL HAZARD WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN RESULT IN DEATH,
SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE
FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION,
CARBON MONOXIDE POISONING, AND/OR ELECTRICAL
SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE
INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH
AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE
MANUFACTURER.
Read all Safety, Operating,
and Maintenance
Instructions
®
FIRST EDITION
PART NO. 18994
Printed In U.S.A.
Price $1.00
CONTENTS
WARNING ICON G 001
WARNING ICON G 001
SAFETY
INFORMATION
SECTION PAGE
Safety Information.........................................................................2
Product Identification .................................................................... 4
Unpacking......................................................................................4
Theory of Operation ......................................................................5
Propane Supply..............................................................................5
Installation .....................................................................................6
Ventilation .....................................................................................7
Operation .......................................................................................7
Storage ........................................................................................... 9
Maintenance .................................................................................. 9
Troubleshooting.............................................................................10
Service Procedures ........................................................................ 11
Illustrated Parts List.......................................................................14-15
Specifications.................................................................................16
WARNINGS
WARNING: FIRE, BURN, INHALATION, AND EXPLOSION
WARNING ICON G 001
HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING
MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE
AWAY FROM THE HEATER AS RECOMMENDED BY THE
INSTRUCTIONS. NEVER USE THE HEATER IN SPACES
WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN
CHEMICALS.
WARNING
NOT FOR HOME OR RECREATIONAL VEHICLE USE.
The heater is designed for use as a construction heater in accordance with ANSI
Z83.7•CGA2.14. Other standards govern the use of fuel gases and heating products
for specific uses. Your local authority can advise you about these. The primary
purpose of construction heaters is to provide temporary heating of buildings under
construction, alteration or repair. Properly used, the heater provides safe economical heating. Products of combustion are vented into the area being heated.
We cannot foresee every use which may be made of our heaters. Check with your
local fire safety authority if you have questions about heater use.
Other standards govern the use of fuel gases and heat producing products for
specific uses. Your local authorities can advise you about these.
Carbon Monoxide Poisoning: Some people are more affected by carbon
monoxide than others. Early signs of carbon monoxide poisoning resemble the flu,
with headaches, dizziness, and/or nausea. If you have these signs, the heater may
not be working properly. Get fresh air at once! Check for proper ventilation and
have heater serviced.
2
Safety Information continues on next page
099597
SAFETY
INFORMATION
Continued
2
099597
!
WARNINGS
Propane Gas: Propane gas is odorless. An odor-making agent is added to propane
gas. The odor helps you detect a propane gas leak. However, the odor added to
propane gas may fade. Propane gas may be present even though no odor exists.
Make certain you read and understand all warnings. Keep this manual for reference.
It is your guide to safe and proper operation of this heater.
• Install and use heater with care. Follow all local ordinances and codes. In the
absence of local ordinances and codes, refer to the Standard for Storage and
Handling of Liquefied Petroleum Gas, ANSI/NFPA 58 and the Natural Gas
Installation Code, CAN/CGA B149.2. This instructs on the safe storage and
handling of propane gases.
• Use only the electrical voltage and frequency specified on model plate.
• The electrical connections and grounding of the heater shall follow the Na-
tional Electric Code, ANSI/NFPA 70 or Canadian Electric Code, Part 1.
• Electrical grounding instructions — This appliance is equipped with a threeprong (grounding) plug for your protection against shock hazard and should
be plugged directly into a properly grounded three-prong receptacle.
• Use only a three-prong, grounded extension cord.
• Use only the hose and factory preset regulator provided with the heater.
• Use only propane gas set up for vapor withdrawal.
• Provide adequate ventilation. Before using heater, provide at least a one-square-
foot opening of fresh, outside air for each 100,000 Btu/Hr of rating. This heater
produces carbon monoxide, which is listed by the State of California as a
reproductive toxin under Proposition 65.
• For indoor use only. Do not use heater outdoors.
• Do not use heater in occupied dwellings or in living or sleeping quarters.
• Do not use heater below ground level. Propane gas is heavier than air. If a leak
occurs, propane gas will sink to the lowest possible level.
• Keep appliance area clear and free from combustible materials, gasoline, paint
thinner, and other flammable vapors and liquids. Do not use heater in areas
with high dust content.
• Minimum heater clearances from combustibles:
Outlet: 6 Ft. Sides: 2 Ft. Top: 6 Ft. Rear: 2 Ft.
• Keep heater at least six feet from propane tank(s). Do not point heater at
propane tank(s) within 20 feet.
• Keep propane tank(s) below 100° F.
• Check heater for damage before each use. Do not use a damaged heater.
• Check hose before each use of heater. If highly worn or cut, replace before
using heater.
• Locate heater on stable and level surface if heater is hot or operating.
• Not intended for use on finished floors.
• Never block air inlet (rear) or air outlet (front) of heater.
• Keep heater away from strong drafts, water spray, rain, or dripping water.
• Do not leave heater unattended.
• Keep children and animals away from heater.
• Never move, handle, or service a hot, operating, or plugged-in heater. Severe
burns may result. Wait 20 minutes after turning heater off.
• To prevent injury, wear gloves when handling heater.
• Never attach duct work to heater.
• Do not alter heater. Keep heater in its original state.
• Do not use heater if altered.
• Turn off propane supply and unplug heater when not in use.
• Use only original replacement parts. This heater must use design-specific
parts. Do not substitute or use generic parts. Improper replacement parts could
cause serious or fatal injuries.
3
PRODUCT
IDENTIFICATION
Hot Air Outlet
(Front)
Shell
Handle
Motor
Fan Guard
Heater Base
UNPACKING
Piezo Ignitor
Button
Automatic
Control Valve
Button
Hose /Regulator
Assembly
Figure 1 - 35,000 BTU/Hr Model
Inlet
Connector
Power
Cord
1. Remove all packing items applied to heater for shipment. Keep plastic cover
caps (attached to inlet connector and hose/regulator assembly) for storage.
2. Remove all items from carton.
3. Check all items for shipping damage. If heater is damaged, promptly inform
dealer where you bought heater.
4
099597
THEORY OF
OPERATION
Clean
Heated
Air Out
(Front)
The Fuel System: The hose/regulator assembly attaches to the propane gas
supply. This provides fuel to the heater.
The Air System: The motor turns the fan. The fan pushes air into and around
the combustion chamber. This air is heated and provides a stream of clean, hot air.
The Ignition System: The piezo ignitor lights the burner.
The Automatic Control System: This system causes the heater to shut down
if the flame goes out.
Combustion
Chamber
Fan
Motor
Cool Air In
(Back)
PROPANE
SUPPLY
Hose/Regulator
Assembly
Air For Combustion Air For Heating
Figure 2 - Cross Section Operational View
Propane gas and propane tank(s) are to be furnished by the user.
Use this heater only with a propane vapor withdrawal supply system. See Chapter 5
of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA
58 and/or CAN/CGA B149.2. Your local library or fire department will have this
booklet.
The amount of propane gas ready for use from propane tanks varies. Two factors
decide this amount:
1. The amount of propane gas in tank(s)
2. The temperature of tank(s)
This heater is designed to operate with a minimum 20-pound propane tank. You
may need two or more tanks or one larger tank in colder weather. Use a 100-pound
tank for longer operation or in very cold weather. Less gas is vaporized at lower
temperatures. Your local propane gas dealer will help you select the proper supply
system. The minimum surrounding air temperature rating for each heater is -20°F
(-29°C).
099597
Average Temperature (°F)
At Tank Location 40° 32° 20° 10° 0° -10° -20°
Number Of Tanks
(100-pound) 1111 1 2 2
5
INSTALLATION
Review and understand the warnings in the Safety Information Section, pages 2 and 3. They are needed to safely
operate this heater. Follow all local codes when using this
heater.
!
WARNING
Test all gas piping and connections for leaks after installation or servicing. Never use an open flame to check for a
leak. Apply a mixture of liquid soap and water to all joints.
Bubbles forming show a leak. Correct all leaks at once.
1. Provide propane supply system (see Propane Supply, page 5).
2. Connect POL fitting on hose/regulator assembly to propane tank(s). Turn POL
fitting counterclockwise into threads on tank. Tighten firmly using wrench.
IMPORTANT:
horizontal position (see Figure 3). This places the regulator vent in the proper
position to protect it from the weather.
Propane
Tank
Position regulator so that hose leaving the regulator is in a
Propane
Supply
Valve
WARNING
!
Regulator
Hose
POL Fitting
Figure 3 - Regulator Position
3. Connect hose to inlet connector. Tighten firmly using a wrench.
IMPORTANT:
between hose/regulator assembly and propane tank. You must use the regulator supplied with heater.
6
Use extra hose or piping if needed. Install extra hose or piping
Inlet Connector
Figure 4 - Hose and Inlet Connector
Hose
099597
4. Open propane supply valve on propane tank(s) slowly.
slowly, excess-flow check valve on propane tank may stop gas flow. If this
happens, close propane supply valve and open again slowly.
5. Check all connections for leaks. Apply mixture of liquid soap and water to gas
joints. Bubbles forming show a leak that must be corrected.
WARNING
!
Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming
show a leak that must be corrected. Correct all leaks at
once.
6. Close propane supply valve.
Note:
If not opened
VENTILATION
OPERATION
WARNING
!
Provide at least a one square foot opening of fresh, outside
air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur.
Provide proper fresh, outside air ventilation before running
heater.
Review and understand the warnings in the Safety Information section, pages 2 and 3. They are needed to safely
operate this heater. Follow all local codes when using this
heater.
To Start Heater
1. Follow all installation, ventilation, and safety information.
2. Locate heater on stable and level surface. Make sure strong drafts do not blow
into front or rear of heater.
3. Plug power cord of heater into a three-prong, grounded extension cord.
Extension cord must be at least six feet long. Extension cord must be UL
listed.
Extension Cord Wire Size Requirements
Up to 50 feet long, use 18 AWG rated cord.
51 to 100 feet long, use 16 AWG rated cord.
101 to 200 feet long, use 14 AWG rated cord.
4. Plug extension cord into a 120 volt/60 hertz, 3-hole, grounded outlet. Motor
will start. Fan will turn, forcing air out front of heater.
WARNING
!
099597
Continued
7
OPERATION
Continued
5. Open propane supply valve on propane tank(s) slowly.
slowly, excess-flow check valve on propane tank may stop gas flow. If this
happens, close propane supply valve and open again slowly.
!
WARNING
Be sure motor and fan are running before pushing in automatic control valve button. Flames could flash outside
heater if motor and fan are not running.
6. Push in and hold automatic control valve button (see Figure 5). Push piezo
ignitor button (see Figure 5). You may need to push piezo ignitor button 3-8
times until the burner lights. When burner lights, keep automatic control valve
button pushed in. Release button after 30 seconds.
Note:
If heater fails to ignite, hose may have air in it. If so, keep automatic
control valve button pressed and wait 20 seconds. Release automatic control
valve button and wait 20 seconds for unburned fuel to exit heater. Repeat step 6.
Note:
If not opened
Piezo Ignitor
Button
Automatic Control
Valve Button
Figure 5 - Automatic Control Valve Button and Piezo Ignitor Button
Notice: If heater is unplugged or power outage occurs while heater is running, the
thermal limit device will stop fuel flow. A few seconds occur before the thermal
limit device activates. During this short time, flames may appear outside the
heater. This is normal. The flames will go out when thermal limit device activates.
To Stop Heater
1. Tightly close propane supply valve on propane tank(s). Allow heater to burn
remaining fuel in hose.
2. Wait a few seconds. Heater will burn gas left in supply hose.
3. Unplug heater.
To Restart Heater
1. Wait five minutes after stopping heater.
2. Repeat steps under To Start Heater, page 7.
8
099597
STORAGE
!
CAUTION
Disconnect heater from propane supply tank(s).
1. Store propane tank(s) in safe manner. See Chapter 5 of Standard for Storage
and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and/or CAN/CGA
B149.2. Follow all local codes. Always store propane tanks outdoors.
2. Place plastic cover caps over brass fittings on inlet connector and hose/regula-
tor assembly.
3. Store in dry, clean, and safe place. Do not store hose/regulator assembly inside
heater combustion chamber.
4. When taking heater out of storage, always check inside of heater. Insects and
small animals may place foreign objects in heater. Remove motor and other
internal parts if needed to remove foreign objects (see Service Procedures,
page 11).
MAINTENANCE
!
WARNINGS
• Never service heater while it is plugged in, connected
to propane supply, operating, or hot. Severe burns and
electrical shock can occur.
• Keep heater clear and free from combustible materials,
gasoline, and other flammable vapors and liquids.
• Do not block the flow of combustion or ventilation air.
1. Keep heater clean. Clean heater annually or as needed to remove dust and
debris. If heater is dirty or dusty, clean heater with a damp cloth. Use household cleaners on difficult spots.
2. Inspect heater before each use. Check all connections for leaks. Apply mixture
of liquid soap and water to connections. Bubbles forming show a leak. Correct
all leaks at once.
3. Inspect hose/regulator assembly before each use. If hose is highly worn or cut,
replace.
4. Have heater inspected yearly by a qualified service agency.
5. Keep inside of heater free from combustible and foreign objects. Remove
motor and other internal parts if needed to clean inside of heater (see Service
Procedures, page 11).
6. Clean fan blades each season or as needed (see Fan, page 12).
099597
9
TROUBLE-
!
SHOOTING
WARNING
Never service heater while it is plugged in, connected to
propane supply, operating, or hot. Severe burns and
electrical shock can occur.
OBSERVED FAULT POSSIBLE CAUSE REMEDY
Fan does not turn
when heater is
plugged in.
No electrical power
to heater
Check voltage to electrical outlet. If voltage is good, check
heater power cord for breaks.
Heater will not
ignite.
Fan hitting inside of
heater shell
Fan blades bent
Defective motor
User did not follow installation or operation instructions properly
No spark at ignitor. To
test for spark, follow step
9 under Ignitor, page 13.
If you see spark at ignitor,
have heater serviced by
qualified service person.
If no spark seen:
A) Loose or disconnected
ignitor wire
B) Wrong spark gap
C) Piezo ignitor loose
D) Bad ignitor electrode
Adjust motor/fan guard to keep
fan from hitting inside of
heater shell. Bend fan guard if
necessary.
Replace fan. See Fan, page 12.
Replace motor. See Motor,
page 11.
Repeat installation and operation instructions. See Installa-
tion, page 6 and Operation,
page 7.
A) Check ignitor wire. Tighten
or reattach loose ignitor wire.
See Figure 13, page 13 for ignitor wire location.
B) Set gap between ignitor
electrode and target plate to
.17".
C) Tighten nut holding piezo
ignitor to base of heater.
D) Replace ignitor electrode.
See Ignitor, page 13.
Heater shuts down
while running.
High surrounding air temperature causing thermal
limit device to shut down
heater.
Restricted air flow
Damaged fan
Excessive dust or debris
in surrounding area
This can happen when running
heater in temperatures above
85°F. Run heater in cooler temperatures.
Check heater inlet and outlet.
Remove any obstructions.
Replace fan. See Fan, page 12.
Clean heater. See Mainte-
nance, page 9.
!
WARNING
Use only in areas free of
high dust content.
10
099597
SERVICE
!
WARNING
PROCEDURES
Electrical System
The entire electrical system for
this heater is contained within
the motor. If any part of the
electrical system is damaged,
you must replace motor.
Motor
1. Remove three screws that
attach fan guard to heater
shell.
2. Remove motor and fan
guard from heater shell (see
Figure 6).
3. Use pliers to remove the
fan nut from front of motor
shaft (see Figure 7).
4. Remove fan. Be careful not
to damage the fan blade
pitch.
5. Remove three nuts that
attach fan guard to motor
using nut-driver. Remove
fan guard from motor (see
Figure 8).
6. Discard old motor.
7. Attach fan guard to new
motor with three nuts.
When attaching fan guard
to motor, you must position
power cord as shown in
Figure 8. Tighten nuts
firmly.
8. Place fan onto motor shaft
of new motor.
IMPORTANT:
placing fan onto motor
shaft, make sure part
number stamped on fan is
facing motor. Attach fan
nut to end of motor shaft.
Tighten fan nut firmly.
9. Place motor and fan guard
into rear of heater shell.
Make sure power cord is
properly located (see Figure
9).
10.Insert three screws through
heater shell and into fan
guard. Tighten screws firmly.
099597
When
Never service heater while it is plugged in, connected to
propane supply, operating, or hot. Severe burns and electrical shock can occur.
Figure 6 - Removing Motor and Fan Guard from Heater
Fan
Nut
Figure 7 - Removing Fan Nut from
Motor Shaft
Figure 8 - Removing or Attaching
Fan Guard from Motor
Figure 9 - Replacing Motor and Fan Guard into Heater
11
Fan
1. Remove three screws that
attach fan guard to heater
shell.
2. Remove motor and fan
guard from heater shell
(see Figure 10).
3. Use pliers to remove the
fan nut from front of motor
shaft (see Figure 11).
4a. If replacing fan, remove
old fan and discard. Go to
step 7 below.
4b.If cleaning fan, remove
fan. Be careful not to
damage the fan blade pitch.
5. Clean fan using soft cloth
moistened with kerosene or
solvent.
6. Dry fan thoroughly.
7. Place fan onto motor shaft.
IMPORTANT:
placing fan onto motor
shaft, make sure part
number stamped on fan is
facing motor.
8. Attach fan nut to end of
motor shaft. Tighten fan
nut firmly.
9. Place motor and fan guard
into rear of heater shell.
Make sure power cord is
properly located (see
Figure 12).
10.Insert three screws through
heater shell and into fan
guard. Tighten screws
firmly.
When
Figure 10 - Removing Motor and Fan Guard from Heater
Fan Nut
Figure 11 - Removing Fan Nut from Motor Shaft
12
Figure 12 - Replacing Motor and Fan Guard into Heater
099597
Ignitor
1. Remove motor and fan
guard from heater (see
Motor, page 11, steps 1 and
2).
2. Remove black ignitor wire
from piezo ignitor. Access
ignitor wire through
underside of heater base
(see Figure 13). Push wire
up through bushing in
heater shell.
3. Remove ignitor mounting
screw from rear head using
nut-driver or standard
screwdriver (see Figure 14).
4. Remove ignitor from rear
head.
5. Install new ignitor. Attach
ignitor to rear head with
ignitor mounting screw.
6. Run ignitor wire from new
ignitor through bushing in
heater shell. Attach ignitor
wire to piezo ignitor.
7. Set gap between ignitor
electrode and target plate to
.17" (see Figure 15).
8. Test for spark.
WARNING: Make sure
heater is disconnected
from propane supply.
Heater could ignite
causing severe burns.
Push piezo ignitor button
and watch for spark between ignitor electrode and
target plate.
9. Place motor and fan guard
into rear of heater shell (see
Motor, page 11, steps 9 and
10).
Piezo Ignitor
Bushing
Ignitor Wire
Underside of
Heater Base
Figure 13 - Removing Ignitor Wire from Piezo Ignitor
Rear
Head
Ignitor
Ignitor
Mounting
Screw
Figure 14 - Removing Ignitor Mounting Screw and Ignitor
Target
Plate
099597
Gap
Area
Ignitor
Electrode
Figure 15 - Clearance between Ignitor Electrode and Target Plate
13
ILLUSTRATED
PARTS
BREAKDOWN
HP35
2
1
HEATER
EXPLODED VIEW
Rubber
Fan
Nut
Washer
23
22
19
21
4
7
6
16
9
8
21
20
3
5
2
24
11
26
Fan
18
17
10
26
Motor
Motor
Assembly
12
14
13
14
27
25
15
099597
PARTS LIST
KEY PART
NO. NO. DESCRIPTION QTY.
1 04754-01 Inner Shell (Combustion Chamber) 1
2 00529-10 Hex Tap Screw, #10-16 x 3/8" 7
3 04754-02 Outer Shell 1
4 00529-44 Handle 1
5 04754-03 Hex Tap Shoulder Screw 4
6 00529-12 Hex Tap Screw, #10-16 x 3/4" 2
7 04754-04 Hex Tap Screw, #12-14 x 1/2" 3
8 03327-31 Thermocouple Clip 1
9 04754-05 Burner Assembly 1
10 04754-06 Electrode Ignitor 1
11 01086-32 Hex Tap Screw, #8-18 x 3/8" 1
12 04754-08 Fan 1
13 04754-09 Motor Assembly (Includes Rubber
Washer and Fan Nut) 1
14 04754-10 Fan Guard 1
15 04754-11 Captive Washer Nut 3
16 03326-20 Hex Screw, #4-40 x 1/4" 2
17 01086-30 Hex Nut, #4-40 2
18 04754-12 Thermal Switch Kit(Including
Hardware and Wire Assemblies) 1
19 03326-14 Universal Bushing 1
20 04754-13 Wire Clip 1
21 04754-14 Thermocouple 1
22 04754-15 Valve/Orifice Assembly 1
23 01087-24 Piezo Ignitor 1
24 03327-03 Sleeve Cap 1
25 04754-16 Base 1
26 04754-17 Lock Washer, #4 4
27 04754-18 Steel Rivet, 1/8" 1
099597
PARTS AVAILABLE - NOT SHOWN
04754-20 General Information Decal 1
04754-22 Operation Decal 1
03326-12 LP Warning Decal 1
04754-23 Notice Decal 1
ACCESSORIES
04754-24 Regulator & Hose Assembly 1
03327-37 10' Hose 1
04754-25 Regulator 1
03326-53 POL Connector 1
15
SPECIFICATIONS
Output Rating (BTU/Hr) 35,000
Fuel Propane Vapor Only
Fuel Consumption
Gallons/Hour .38
Pounds/Hour 1.6
Supply Pressure To Regulator
Minimum (for purposes 10 psi
of input adjustment)
Maximum Tank Pressure or 200 psi
Regulator Outlet Pressure 11" WC
Manifold Pressure 10.8" WC
Hot Air Output
(CFM Approx) 175
Motor 2735 RPM
Electric Input 120 volt/60 hertz
Amperage 2
Ignition Manual, Piezo
Weight (Pounds)
Heater 14.5
Shipping 16
Size - L x W x H (Inches)
Heater 18.5 x 7.7 x 12.8
Temperature Range for Heater Operation -20° F to 85° F*
* When running heater in temperatures above 85° F, high internal temperatures
may cause thermal limit device to shut down heater.
16
099597
NOTES
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
099597
____________________________________________________
____________________________________________________
____________________________________________________
____________________________________________________
__________________________________________________
17
NOTES
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
18
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
099597
NOTES
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
099597
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
19
CUSTOMER ASSIST ANCE
FOR THE LOCATION OF YOUR NEAREST HOMELITE SERVICING DEALER IN THE
UNITED STATES, PUERTO RICO, AND THE VIRGIN ISLANDS
CALL: 1-800-242-4672
NOTE: DEALER INFORMATION, TECHNICAL ADVICE, AND PRODUCT
INFORMATION CAN BE OBTAINED AT THIS NUMBER.
HEADQUARTERS
HOMELITE
P.O. BOX 7047
CHARLOTTE, N.C. 28241
OVERSEAS OFFICES
NETHERLANDS
(HDQS. — Europe, Africa and Middle East)
2153 GB Nieuw Vennep
FRANCE
HOMELITE
S.A.R.L.
Z.I. du Vert-Galant
Rue du Chateau/Rue de la Garenne
95310 Saint-Quen-L’Aumone
France
HOMELITE
ATLANTIC
Haverstraat 24
The Netherlands
AUSTRALIA
HOMELITE
PACIFIC LIMITED
HEADQUARTERS
22 Terra-Cotta Drive
Blackburn, 3130
Victoria, Australia
CANADIAN OFFICES
HOMELITE
CANADA LIMITED
1850 55th Avenue
Lachine, Quebec, Canada
H8T 3J5
212-214 590 Ebury Place
New Westminster, British Columbia
V3M 6K7
595 Canarctic Drive
Toronto, Ontario
M3J 2P9
1395
A Subsidiary of Deere & Company
inc.
099597-01
Rev. E
9/97
Loading...