Hobart LXiG General Manual

Item # _____________________________________

Quantity ___________________________________

C.S.I. Section 11400

LXiG

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

STANDARD FEATURES

■ 30 racks per hour

■ .74 gallons of water per rack

■ Hot water or chemical sanitation units available

■ Low chemical alert indicator

■ Sense-A-Temp™ booster heater capable of

70° rise, provided on LXiGH models

■ Delime notiﬁcation with cycle

■ Chemical pump “auto-prime”

■ Service diagnostics

■ Fresh water rinse

■ 16 gauge stainless steel tank

■ Microcomputer, top mounted controls with

digital cycle/temperature display

■ Revolving upper and lower anti-clogging wash arms

■ Revolving upper and lower rinse arms

GLASSWASHER

STANDARD VOLTAGES

❑ 120/60/1 (LXiGC model only)

❑ 120/208-240(3W)/60/1

VOLTAGE OPTIONS AT EXTRA COST

❑ 208-240(2W)/60/1

ACCESSORIES

❑ Power cord kits

❑ Pressure regulator valve

❑ Caster assembly kit

❑ Trim kit, top cover

❑ Rolled top, dish rack holder

❑ DWT2 drain water tempering kit

Speciﬁcations, Details and Dimensions on Back.

■ Removable stainless steel scrap screen

■ Corrosion resistant pump

■ Automatic pumped drain

■ 12" door opening

■ Automatic ﬁll

■ Labyrinth-type door seal

■ Electric tank heat

■ Two dishracks – one peg and one combination-

type

■ Detergent and rinse aid pumps

LXiG GLASSWASHER

F-8367 – LXiG Glasswasher Page 1 of 2

Printed On Recycled Paper

LXiG GLASSWASHER

WARNING:

REQUIRED FLOWING WATER PRESSURE TO THE GLASSWASHER IS 20 ± 5 PSIG. IF PRESSURES HIGHER THAN 25 PSIG ARE PRESENT, A PRESSURE REGULATING VALVE MUST BE INSTALLED IN THE WATER LINE TO THE GLASSWASHER (BY OTHERS).

IMPORT ANT: THE SO DIUM HYPOCH LORITE (LIQUID BL EACH) CONTA INER S HOULD BE PLACED NO HI GHER THAN 10" ABOVE FLOOR.

IF BLEACH CONTAINER IS TO BE PLACED IN CABINET ADJACENT TO GLASSWASHER, A 1/2" DIA. HO LE IS REQUIRED IN THE CABINET TO RUN BLEACH SUPPLY LINE.

USE ONLY 6% SODIUM HYPOCHLORITE (LIQUID BLEACH) AS SANITIZING CHEMICAL TO INSURE PROPER OPER ATION OF DISHMACHINE. IF 8.4% IS TO BE UTILIZED, CONTACT HOBART SERVICE TO CHANGE THE SANITIZER PUMP SETTINGS.

DO NOT PRE-M IX WETTING AGENT AND SODIUM HYPOCHLORITE (LIQUID BLEACH). CERTAIN MATERIALS INCLUDING SILVER PLATE, ALUMINUM AND PEWTER ARE ATTACKED

BY SODIUM HY POCHLORITE (LIQUID BLEACH). SEE INSTRUCTION MANUAL.

NOTES:

1. A LL VERTICAL MACHINE DIMENSIONS TAKEN FROM FLOOR MAY BE INCREASED BY 1".

2. M OIST AIR ESCAPES FROM THE DOOR. USE ONLY MOI STURE RESISTANT MATERIALS ADJACENT TO LXiG SIDES AN D TOP.

3. A VENT HOOD IS N OT RECOMMENDED ABOVE THE LXiG UNDERCOUNTER GLASSWASHER SINCE IT DOE S NOT PRODUCE EXCESSIVE VAPORS

PLUMBING NOT ES:

1. W ATER HAMMER ARRESTOR (MEETING ASSE-1010 S TANDARD OR EQUIVALEN T) TO BE SUPPLIED (BY OTHERS) IN COMMON WATER SUPPLY LINE AT SERVICE CONNECTION.

2. R ECOMMENDED WATER HARDNESS TO BE 4-6 GRAINS FOR BEST RESULTS.

3. M INIMUM WATER CONDUCTIVITY REQUIRED - 30 MICRO-MHOS/CM.

4. I F DRAIN HOSE IS LOOPED ABOVE A SINK, THE LOOP MUST NOT EXCEED 38 " AFF.

ELECTRICAL A ND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIO NAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.

PLUMBING CON NECTIONS MUST COMPLY WITH APPLICABLE S ANITARY, SAFETY AND PLUMBING CODES. DRAIN AND FILL LINE CONFIGURATIONS VARY, SOME M ETHODS ARE SHOWN ON THIS DRAWING.

WARNING

LEGEND

E1 ELECTRICAL C ONNECTION: 1-3/8" DIA. HOLE FOR

P1 SINGLE FILL AND RINSE CONNECTION: 3/4" FEMALE

P2 DRAIN CONNECTION: 3/4" MPT FITTING WITH

CONNECTION I NFORMATION

(AFF = ABOVE FINISHED FLOOR)

1" TRADE SIZ E CONDUIT; 31-3/4" AFF.

GARDEN HOSE FITTING ON 6' LONG HOSE SUPPLIED WITH MACHINE ; 140°F WATER MIN. FOR LXiGC, 110°F WATER MIN. FOR LXiGH, 1-1/2" AFF.

6' LONG HOSE SUPPLIED WITH MACHINE; 3-9/16" AFF.

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

MACHINE TYPE & RATED

CKT CONDUCT PROTECTIVE

SPECIFICATIO N AMPS

LXiGC (120/6 0/1) USE 90°C STR ANDED 15.4 20 20 COPPER WIRE ONLY.

LXiGC (120/2 08-240(3W)/60/1*) LXiGC (208-2 40/60/1) USE 90°C STR ANDED COPPER WIRE ONLY.

LXiGH (120/2 08-240(3W)/60/1*) LXiGH (208-2 40/60/1) USE 90°C STR ANDED COPPER WIRE ONLY.

ELECTRICAL O PTIONS BELOW ARE NON STANDARD VOLTAGES AVAILABLE AT EXTRA COST. CONSULT FACTORY FOR PRICING AND LEAD TIME.

LXiGH 208-240/60/3 29.5 35 35 480/60/3 14.8 20 20 220-240/50/1 38.1 50 50 380-400/60/3 17.1 25 25

MIN SUPPLY MAX

AMPACITY DEVICES

13.6 20 20

37.7 50 50

* THIS SYSTEM REQUIRES THREE POWER WIRES WHICH INCLUDES A CURRENT CA RRYING NEUTRAL, AN ADDITIONAL FOURTH WIRE MUST BE PROV IDED FOR MACHINE GROUND.

ACCESSORY CO RD KITS AVAILABLE FOR ALL MACHINES

SHIPPING WEI GHTS (LBS) LXiGC LXiGH

NET WEIGHT O F MACHINE 194 lbs. 214 lbs.

DOMESTIC SHI PPING WEIGHT 239 lbs. 259 lbs.

As continued product improvement is a policy of Hobart, speciﬁcations are subject to change without notice.

Page 2 of 2 F-8367 – LXiG Glasswasher

F-8367 (REV. 10/07) LITHO IN U.S.A. (H-01)

MODELS:

iGC, LXiGH

892881