Hobart FT1000D User Manual

Item # _____________________________________

Quantity ___________________________________

C.S.I. Section 11400

FT1000D ENERGY RECOVERY

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

STANDARD FEATURES

■ Pumped rinse system

■ Water usage 58 gph

■ Digital controls with machine diagnostics

■ Low temperature alert

■ Single point vent connection

■ 36" access doors on prewash, power wash and

power rinse chambers, 25" door access on dual rinse chamber and ASR chamber

■ Start and stop switches at both ends

■ Doors open indicator

■ Drains open indicator

■ Door interlocks

■ 3 H.P. prewash, and 5 H.P. power wash and

power rinse pump motors, all TEFC

■ Capless Auto Clean wash arms

■ Easy to remove scrap trays and baskets

■ Deep drawn tanks without welds

■ 30" wide conveyor belt

■ Dual Rinse

■ Automatic Soil Removal system (ASR)

■ Auto Clean feature

■ Auto Delime feature

■ Energy Recovery

■ Front and rear panels

■ Variable speed conveyor

FLIGHT-TYPE DISHWASHER

MODEL

❑ FT1000D Energy Recovery Flight-Type

Dishwasher

OPTIONS AT EXTRA COST

❑ Electric Tank Heat

❑ Steam Tank Heat

❑ Booster Heater ❑ Electric ❑ Steam

❑ Blower Dryer ❑ Electric ❑ Steam

❑ 6" higher than standard chamber

❑ Multiple conveyor choices

❑ Circuit breakers

❑ Other options available, consult factory

ACCESSORIES

❑ Feet ❑ Extended ❑ Flanged

❑ Water hammer arrestor/PRV

Specications, Details and Dimensions on Inside and Back.

FT1000D ENERGY RECOVERY FLIGHT-TYPE DISHWASHER

UL, NSF and LA approvals pending

DIRECTION OF OPERATION

❑ Right to Left

❑ Left to Right

VOLTAGE

❑ 208/60/3

❑ 240/60/3

❑ 480/60/3

❑ Other voltages available – consult factory

F40351 – FT1000D Energy Recovery Flight-Type Dishwasher Page 1 of 20

FT1000D ENERGY RECOVERY FLIGHT-TYPE DISHWASHER

DESIGN: Fully automatic, ight-type dish machine

consisting of a load section with Automatic Soil Removal system, power recirculating prewash, power wash, power rinse, dual rinse and nal rinse section. Included with each machine will be exible plastic strip curtains to control overspray.

CONSTRUCTION: Stainless steel tank and chambers with No. 3 polish on appearance surfaces. Frame, legs and feet to be constructed of stainless steel. Inspection doors to be chamber width.

PUMPS: Recirculating stainless steel pumps with stainless steel impellers. Pump housing has easy to remove coverplate for access to impeller. All pumps are self-draining.

MOTORS: Totally enclosed fan cooled (TEFC) design with overload protection. Pump motors to be 3 H.P. for prewash and 5 H.P. for power wash and power rinse, with conveyor motor to be 1⁄3 H.P. Available in electrical specications of 208/60/3, 240/60/3 and 480/60/3.

CONTROLS: A stainless steel control center with electronic digital controls mounted at eye level. Power “On/Off” and “Start/Stop” switches integrated into keypad. Digital display indicates door(s) open, low temperature alert, tanks/nal rinse temperatures, Auto Clean and Auto Delime instructions and notications, and other pertinent operating data. Additional “Start/Stop” switches are located at each end of machine. Conveyor speed button included on the control center to provide for the adjustable speed conveyor.

FLIGHT-TYPE CONVEYOR: Stainless steel side links, tie rods and conveyor tracks. Injection molded, resilient Duraex ight links.

VENT: Single built-in vent duct with dampers mounted in ventilation stack.

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

AUTOMATIC SOIL REMOVAL SYSTEM (ASR): Two foot section with specialized soil removal wash arms removes food soil from the machine before it reaches the prewash tank. System will pump food soil from the ASR tank into an external collector located under the load section, minimizing the need to pre-scrap dishes and reducing detergent consumption. Operator can easily remove and clean external collector without interruption of machine operation.

RECIRCULATING PREWASH SECTION: Prewash compartment is tted with upper and lower wash arms. Prewash ush down for prewash tank bed. Large removable one piece perforated stainless steel screen sloped downward to deep stainless steel scrap basket.

TANK HEAT: Power wash, power rinse and dual rinse tank water temperatures are thermostatically controlled. Low water protection is provided. Specify either electric or steam heat.

FINAL RINSE: Easily removed nal rinse arms.

ENERGY RECOVERY: Energy Recovery system

operates with a cold water line, capturing energy from exhaust air, and using it to elevate the temperature of the water entering the booster heater. The result is savings – both in hot water and in energy.

CONVEYOR DRIVE UNIT: Powered by a 1⁄3 H.P. motor. Trip mechanism provided on unload section. Jam protection is provided by load sensing switch at drive platform. Conveyor speed adjustment of 6.5 feet per minute to 8.5 feet per minute is provided on the digital display keypad.

DRAINS: Manual, hand-operated, located in each tank.

One automatic master drain to be used for Auto Clean and Auto Delime.

BLOWER DRYER (OPTIONAL): Includes (2) 1 H.P. fan motors with sealed ball bearings and overload protection. Blower functions only during conveyor operation.

Page 2 of 20 F40351 – FT1000D Energy Recovery Flight-Type Dishwasher

FT1000D ENERGY RECOVERY

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

No other control system allows easier monitoring.

The digital controls are placed in a convenient panel that lets operators verify proper operation and temperatures at a glance. Digital display indicates the unit is on, and conrms that the doors are closed. Automatic door interlocks prevent the pump and conveyor from operating if the doors are open. Easy-to-read digital display indicates accurate temperatures of the 150°F wash, 160°F power rinse, 160°F dual rinse and 180°F nal rinse — critical for proper HACCP system record-keeping.

Stainless steel pump is built for long life.

The stainless steel pump housing and impeller offer greater durability and long life. The pump motor is totally enclosed and fan cooled (TEFC) to protect it from water spray during dishroom clean-up.

Scrap baskets capture food particles and are easy to clean.

The sloped screens that carry scraps to the scrap baskets are steeper, so less soil gets into the tanks. The basket opening is larger for easy cleaning and basket handles have been designed for easy lift-out access. The load section also features a removable scrap basket which contains soil that is pumped from the ASR section. All scrap baskets and strainers are stainless steel for strength and durability.

The FT1000 Series saves water and energy.

The unit has the lowest water and energy consumption in

the industry, yet provides effective cleaning and sanitizing that meets NSF International requirements.

This is achieved through a carefully balanced ratio of water ow to pressure. Insulated doors and thermal layered curtain at load also reduce heat loss. The unit’s 58 gallons per hour rinse ow rate saves both water and the energy to heat it.

FLIGHT-TYPE DISHWASHER

Wider, variable speed conveyor offers increased throughput.

The conveyor on the FT1000 Series is wider so it can handle more ware. Result: more volume and versatility, quicker work. Its speed is easily adjustable for the type of ware, soiled condition, or workforce requirements. It runs at 6.5 -

8.5 feet per minute.

Energy Recovery system reclaims heat for energy.

The Energy Recovery system captures escaping heat and steam from the exhaust air and uses a heat exchanger to recycle it into energy. This free energy is used to preheat the incoming water supply before it enters the booster heater. The cold ground temperature water passes through a heat exchanger positioned directly in line with the machine’s exhaust system to capture the energy from the exhaust air to elevate the temperature of the water to 128° before it enters the booster heater.

Self-draining pumps help keep water clean.

Pumps are self-draining when the machine is shut down, so there is no residual water left in the pumps.

Installation is quick and easy with modular design, minimal wiring connections, and single point vent.

Modular design means the FT1000 installs quickly and reliably. Sections t through 42" doors. The control panel is already in place, premounted to the power wash/power rinse/ nal rinse section.

Wiring connections are minimal, and there is only a single vent connection, saving time and expense. The control box uses a “single plane” circuitry design for easy accessibility during installation and service. The FT1000 is ready to run quickly.

F40351 – FT1000D Energy Recovery Flight-Type Dishwasher Page 3 of 20

FT1000D ENERGY RECOVERY

SEE NO

TE (e)

FLOOR LINE

7 7/8"

OVER FRAME "A"

3 15/16"

6" MINIMUM

ON THE TOP

FLOOR LIN

NOTE: REFER TO LATEST

NOTE: OVERALL LENGTH OF MACHINE IS DIMENSION "A" + 11 3/4"

63 3/8"

ELECTRIC L-R

18 3/4"

37 1/2"

P3P4

2 5/8"

LOAD "B"

25 9/16"

9 15/16"

13' 1-9/16"

35 7/16" 35 7/16" 35 7/16" 25 9/16"

5 3/4"

11 13/16"

E6E7

P1 P4

60"

52"

44 9/16"

EXHAUST HOOD SUPPLIED BY OTHERS

23 3/4"

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

P2 P1

23 3/4"

55 11/16"

UNLOAD "C"

62 3/4"

(f)

EDITION OF NATIONAL ELECTRICAL CODE AND LOCAL BUILDING CODES

FOR PROPER CLEARANCE

NOTE: STRAINER PANS REQUIRE 35" TO BE REMOVED. EXTRA CLEARANCE SHOULD BE PROVIDED.

36 1/2"

LOAD

END

35"

ASR

40 3/8"

44 13/16"

see note (a)

PRE-

WASH

DIRECTION OF OPERATION

22" HIGH X 29-13/16" WIDE OPENING WILL HANDLE 18" X 26" BUN PANS

NOTE: CLEARANCE FROM WALL 24" RECOMMENDED, WITH DETERGENT DISPENSER

POWER

WASH

POWER

RINSE

AUX

FNL

RNS

FT1021 (2-1/2'-13'-5-1/2') FT1022 (3-1/2'-13'-5-1/2') FT1023 (4-1/2'-13'-5-1/2') FT1023 (2-1/2'-13'-7-1/2') FT1024 (3-1/2'-13'-7-1/2') FT1025 (4-1/2'-13'-7-1/2') FT1025 (2-1/2'-13'-9') FT1026 (3-1/2'-13'-9') FT1027 (4-1/2'-13'-9') FT1027 (2-1/2'-13'-11') FT1028 (3-1/2'-13'-11') FT1029 (4-1/2'-13'-11') FT1030 (2-1/2'-13'-15') FT1031 (3-1/2'-13'-15') FT1032 (4-1/2'-13'-15') FT1032 (2-1/2'-13'-17') FT1033 (3-1/2'-13'-17') FT1034 (4-1/2'-13'-17')

MODEL NO.

UNLOAD

END

"A" "B" "C"

21' 4" 22' 3-3/4" 3' 7-1/4" 23' 3-19/32" 4' 7-3/32" 23' 3-1/2" 2' 7-1/2" 24' 3-1/4" 3' 7-1/4" 25' 3-3/32" 4' 7-3/32" 24' 11-1/4" 2' 7-1/2" 25' 11" 26' 10-27/32" 4' 7-3/32" 26' 10-7/8" 27' 10-5/8" 28' 10-15/32" 30' 6-3/16" 2' 7-1/2" 31' 5-15/16" 3' 7-1/4" 32' 5-25/32" 4' 7-3/32" 32' 5-3/4" 33' 5-1/2" 34' 5-11/32" 4' 7-3/32"

36 1/4"

2' 7-1/2"

3' 7-1/4"

2' 7-1/2" 3' 7-1/4" 4' 7-3/32"

2' 7-1/2" 3' 7-1/4"

89 3/8"

SEE NO

5' 7" 5' 7" 5' 7" 7' 6-1/2" 7' 6-1/2" 7' 6-1/2" 9' 2-1/4" 9' 2-1/4" 9' 2-1/4" 11' 1-7/8" 11' 1-7/8" 11' 1-7/8" 14' 9-3/16" 14' 9-3/16" 14' 9-3/16" 16' 8-3/4" 16' 8-3/4" 16' 8-3/4"

Page 4 of 20 F40351 – FT1000D Energy Recovery Flight-Type Dishwasher

FT1000D ENERGY RECOVERY

GENERAL NOTES:

(

THE CONTROL

TION

CLEARANCE FOR DOORWAYS.

ELECTRICAL WARNING:

ITH

SERVICE WIRE TEMPERATURE RATING: 90C.

PLUMBING NOTES:

(b)

(

(d)

(

SALES ENGINEERING.

VENTILATION NOTES:

SH,

Do not premix other chemicals and sodium hypochlorite (liquid bleach). Mixing may cause hazardous gas to form.

Electrical and grounding connections must comply with the applicable portions of the National Electrical Code and/o other local electrical codes.

Plumbing connections must comply with applicable sanitar codes. vary, some methods are shown on this drawing.

Pressur Important:

abo If ch

a 1/2" dia. Use only 6%

chemical Certain

attacked manual.

MODEL: FT1000 ENERGY RECO (ASR ELECTRIC L-R OPERA 00-949505 REV A

ELECTRICAL CONNECTIONS COMMON ON

ND RINSE FEEDERS

E2 ELECTRIC CONNECTION (SWITCH CONTACTS) 1/2" CONDUIT. 79-1/8" AFF

ELECTRICAL CONNECTIONS W/O CIRCUIT BREAKERS:

E7 1" CONDUIT. 79-1/8" AFF

ELECTRICAL CONNECTIONS

1-1/4" CONDUIT, 79-1/8" AFF

PLUMBING CONNECTIONS:

P2 COMMON COLD

D END OPTION IS SPECIFIED).

2" FPT. 7" AFF

VENTILATION REQUIREMENTS:

BLE OF

95-3/8" AFF see note (f).

SERVICE CONNECTION W/O CIRCUIT BREAKERS

480/60/3

ELECTRIC TANK HEAT, WASH

ELECTRIC TANK HEAT, BOOSTER

480/60/3

25.8 35 35

MOTORS AND CONTROLS

480/60/3

MOTORS

SIZE

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

a) THE CONTROL BOX IS ATTA CHED TO THE CENTER SECTION, AND

BOX IS ROTATED 90 DEGREES ALLOWING THE CENTER SECTION TO FIT THROUGH A 42" WIDE, 7' DOOR OPENING.

WITH BACK PANEL AND END CAPS REMOVED, CONTROL PANEL HINGED BACK AND ALL REAR PIPING REMOVED, OVERALL WIDTH OF MACHINE IS 40".

AFF = ABOVE FINISHED FLOOR ALL DIMENSIONS TAKE FROM THE FLOOR LINE MAY INCREASE 3-1/4" WITH

LEG ADJUSTMENT. FOR CONVENIENCE WHEN CLEANING, CUSTOMER SHOULD INSTALL WATER

TAP NEAR MACHINE WITH 30 FT. OF HEAVY DUTY HOSE WITH SQUEEZE VALVE. THIS DRAWING IS SUPPLIED AS A REFERENCE FOR CONNECTION INFORMA

ONLY. IT WILL NOT BE UTILIZED FOR MANUFACTURING OF UNIT. INSULATED TOP COVER TOP COVER PANELS CAN BE TEMPORARILY REMOVED

FROM THE PRE-WASH, WASH OR POWER RINSE SECTIONS TO YIELD 61-3/4"

LECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY W THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER ELECTRICAL CODES.

PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITAR SAFETY AND PLUMBING CODES.

RECOMMENDED WATER HARDNESS TO BE 3 GRAINS OR LESS PER GALLON FOR BEST RESULTS.

RECOMMENDED BUILDING FLOWING HOT WATER PRESSURE TO THE DISHWASHER IS 30-35 PSI.

c) RECOMMENDED BUILDING FLOWING COLD WATER PRESSURE TO THE

DISHWASHER IS 20 PSI (40-45 PSI WHEN EQUIPPED WITH AUTOCLEAN OPTION IS SPECIFIED). IF COLD WATER IS LESS THAN 55°F CONTACT SALES ENGINEERING.

WATER HAMMER ARRESTOR (MEETING ASSE-1010 STANDARD OR EQUIVALENT) TO BE SUPPLIED (BY OTHERS) IN FINAL RINSE WATER SUPPLY LINE AT SERVICE CONNECTION.

e) IF STEAM PRESSURE IS UNDER 15 PSI AT THE DISHWASHER, CONTAC

(f) THIS DIMENSION IS SUBJECT TO NORMAL SHEET METAL TOLERANCES (g) THE VENT STACK AND ITS ENCLOSURE CAN BE TEMPORARILY REMOVED FROM

THE ENERGY RECOVERY UNIT TO YIELD 81-78" CLEARANCE FOR DOORWAYS (h) THE INSULATED TOP COVER PANELS CAN BE TEMPORARILY REMOVED FROM THE PREWA

WASH OR POWER RINSE SECTIONS TO YIELD 61-3/4" CLEARANCE FOR DOORWAYS.

(j) BACK DRAFT PREVENTER RECOMMENDED (REQUIRED ON MACHINES EQUIPPED WITH ER)

y, safety and plumbing

Drain and ﬁll line conﬁgurations

e gauge not required on pumped rinse machines.

Chemical c ontainers sh ould be plac ed no higher than 10"

ve ﬂoor.

emical conta iners are to be placed in cabinet ad jacent to ma chine

hole is req uired in the cabinet to r un chemical supply line.

or 8.4% sod ium hypochlor ite (liquid bleach) as sanitizing

to insure proper operat ion of dishmachine.

materials in cluding silv er plate, aluminum and pewter a re

by sodium hyp ochlorite (li quid bleach). See instruc tional

, ER)

F40351 – FT1000D Energy Recovery Flight-Type Dishwasher Page 5 of 20

VERY

TION

ALL MODELS:

ELECTRIC CONNECTION, DETERGENT A (MACHINE SERVICE VOLTAGE), 1/2" CONDUIT. 79-1/8" AFF

ELECTRIC CONNECTION, MOTORS & CONTROLS, 1" CONDUIT. 79-1/8" AFF

ELECTRIC TANK HEAT CONNECTION, POWER RINSE TANK, 20 KW 1" CONDUIT. 79-1/8" AFF

ELECTRIC TANK HEAT CONNECTION, WASH TA NK, 20 KW. 1" CONDUIT. 79-1/8" AFF

ELECTRIC TANK HEAT CONNECTION, D UAL RINSE TANK, 10KW. 1" CONDUIT. 79-1/8" AFF

ELECTRIC TANK HEAT CONNECTION, B OOSTER, 18KW.

WITH CIRCUIT BREAKERS:

E8 ELECTRIC CONNECTION, MOTORS, CONTROLS, RINSE HEAT, BOOSTER HEAT (WHEN CIRCUIT BREAKER OPTION IS SPECIFIED) (TB1) 2" CONDUIT, 79-1/8" AFF

E9 ELECTRIC CONNECTION, WASH HEAT & DUAL RINSE HEAT (TB2)

COMMON HOT WATER CONNECTION (AUTOMATIC FILL) 140°F WATER, MINIMUM, 1" FPT, 5-1/2" AFF see notes (b) AND (d).

AUTO CLEAN OPTION) 55°F WATER MINIMUM. 1" FPT, 5-1/2" AFF see notes (b) and (d).

COMMON DRAIN CONNECTION, (WHEN DRAIN TO LOAD END IS SPECIFIED). 2" FPT. 7" AFF

COMMON DRAIN CONNECTION, (WHEN DRAIN TO UNLOA

MINIMUM OF 24" SQUARE VENT HOOD (SUPPLIED BY OTHERS) CAPA PROVIDING 706 CFM EXHAUST (AT STANDARD AIR CONDITIONS).

SERVICE CONNECTION WITH CIRCUIT BREAKERS

(2) SERVICE CONNECTIONS AS SHOWN BELOW

MOTORS, CONTROLS, POWER RINSE & BOOSTER HEAT(TB1)

(1) SERVICE CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3 480/60/3

(1) SERVICE CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3 480/60/3

(5) SERVICE CONNECTIONS AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3 480/60/3

RATED

AMPS

156.3

144.9

72.4

WASH, DUAL RINSE HEAT(TB2)

RATED

AMPS

96.1 125 125

91.6 125 125

45.8 60 60

ELECTRIC TANK HEAT, DUAL RINSE

(1) 10KW CONNECTION AS SHOWN BELOW

RATED

AMPS

30.0

28.6

14.3

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

200 200 175 175

90 90

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

35 35 35 35 20 20

ASR PUMP

ASR SOIL

PREWASH

WASH

POWER RINSE

DUAL RINSE

PUMPED RINSE

EXHAUST

CONVEYOR

WATER CONNECTION (FINAL RINSE WITH OR W/O THE

MAXIMUM

PROTECTIVE

DEVICES

MAXIMUM

PROTECTIVE

DEVICE

MAXIMUM

PROTECTIVE

DEVICES

1/3 HP 1/4 HP

3 1/2 HP

5 HP

5 HP 1/6 HP 1/2 HP 1/3 HP 1/3 HP

ELECTRIC L-R

, VENT FAN CONTROL.

ELECTRIC TANK HEAT, POWER RINSE

(1) 18 KW CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3

(1) 22 KW CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3 480/60/3

(1) 18 KW CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3

(1) SERVICE CONNECTION AS SHOWN BELOW

ELEC.

SPECS.

208/60/3 240/60/3

RATED

AMPS

54.0 70 70

51.5 70 70

25.8 35 35

RATED

AMPS

66.0 80 80

63.0 80 80

31.5 40 40

RATED

AMPS

54.0 70 70

51.5 70 70

RATED AMPS

48.2 60 60

41.8 50 50

20.9 25 25

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

MINIMUM

SUPPLY

CONDUCTOR

AMPACITY

MAXIMUM

PROTECTIVE

DEVICES

MAXIMUM

PROTECTIVE

DEVICES

MAXIMUM

PROTECTIVE

DEVICES

MAXIMUM

PROTECTIVE

DEVICE

FT1000D ENERGY RECOVERY

SEE NO

FLOOR LINE

7 7/8"

OVER FRAME "A"

3 15/16"

6" MINIMUM

ON THE TOP

FLOOR LIN

NOTE: REFER TO LATEST

NOTE: OVERALL LENGTH OF MACHINE IS DIMENSION "A" + 11 3/4"

63 3/8"

ELECTRIC R-L

P2 P1

23 3/4"

55 11/16"

UNLOAD "C"

60"

52"

44 9/16"

EXHAUST HOOD SUPPLIED BY OTHERS

23 3/4"

701 S Ridge Avenue, Troy, OH 45374

1-888-4HOBART • www.hobartcorp.com

P1 P4

18 3/4"

P3 P4

2 5/8"

9 15/16"

E6 E7

5 3/4"

13' 1-9/16"

35 7/16"35 7/16"35 7/16"25 9/16"

25 9/16"

LOAD "B"

11 13/16"

37 1/2"

EDITION OF NATIONAL

ELECTRICAL CODE AND

LOCAL BUILDING CODES

FOR PROPER CLEARANCE

NOTE: STRAINER PANS REQUIRE 35" TO BE REMOVED. EXTRA CLEARANCE SHOULD BE PROVIDED.

89 3/8"

TE (e)

35"

36 1/4"

40 3/8"

44 13/16" see note (a)

UNLOAD

END

22" HIGH X 29-13/16" WIDE OPENING WILL HANDLE 18" X 26" BUN PANS

NOTE: CLEARANCE FROM WALL 24" RECOMMENDED, WITH DETERGENT DISPENSER

FNL RNS

AUX RNS

POWER

RINSE

POWER

WASH

DIRECTION OF OPERATION

MODEL NO.

PRE-

WASH

ASR

"A" "B" "C"

LOAD

END

2' 7-1/2"

3' 7-1/4"

2' 7-1/2" 3' 7-1/4" 4' 7-3/32"

2' 7-1/2" 3' 7-1/4"

5' 7" 5' 7" 5' 7" 7' 6-1/2" 7' 6-1/2" 7' 6-1/2" 9' 2-1/4" 9' 2-1/4" 9' 2-1/4" 11' 1-7/8" 11' 1-7/8" 11' 1-7/8" 14' 9-3/16" 14' 9-3/16" 14' 9-3/16" 16' 8-3/4" 16' 8-3/4" 16' 8-3/4"

36 1/2"

62 3/4"

SEE NO

(f)

Page 6 of 20 F40351 – FT1000D Energy Recovery Flight-Type Dishwasher

+ 14 hidden pages