Hilti PSA 80, PSA 82, PSA 81, PSA 83, PUA 86 Operating Instructions Manual
...
PSA / PUA
English
Printed: 20.03.2017 | Doc-Nr: PUB / 5070470 / 000 / 04
Printed: 20.03.2017 | Doc-Nr: PUB / 5070470 / 000 / 04
English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of signs used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used in combination with a symbol:
DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING! Draws attention to a potential hazard that could lead to serious personal injury or
fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to slight personal
injury or damage to the equipment or other property.
1.2.2 Symbols
The following symbols are used:
Read the operating instructions before use.
Instructions for use and other useful information
Protection class II (double-insulated)
For indoor use only
1.2.3 Illustrations
The following symbols are used in illustrations:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
Item reference numbers are used in the overview illustration and refer to the numbers used in
the product overview section.
1.3 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment may present hazards when used incorrectly by
untrained personnel or when used not as directed.
▶ Make a note in one of the following tables of the designation and serial number printed on the type
identification plate.
▶ Always quote this information when you contact a Hilti representative or Hilti Service to enquire about
the product.
PSA 80, PSA 81, PSA 82 and PSA 83 product information
Battery PSA 80 | PSA 81 | PSA 82 | PSA 83
Generation 01
Serial no.
PSA 81 Product information
Battery PSA 81
Generation 02
Printed: 20.03.2017 | Doc-Nr: PUB / 5070470 / 000 / 04
2 English
Serial no.
PSA 81 Product information
Battery PSA 81
Generation 05
Serial no.
PSA 85 and PSA 86 product information
Charger PSA 85 | PSA 86
Generation 01
PUA 81 and PUA 85 19V product information
AC adapter PUA 81 | PUA 85 19V
Generation 01
PUA 82 and PUA 86 19V product information
Motor vehicle power
adapter
PUA 82 | PUA 86 19V
Generation 01
1.4 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives
and standards. A copy of the declaration of conformity can be found at the end of this documentation.
The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany
2 Safety
2.1 Additional safety instructions
Personal safety
▶ Modification of the tool is not permitted.
▶ Do not use force when inserting the batteries in the tool.
▶ The tool is not intended for use by debilitated persons who have received no special training. Keep the
tool out of reach of children.
▶ This appliance may be used by children 8 years of age or older and by persons with physical, sensory
or mental disabilities or little relevant experience or know-how so long as they are supervised or they
have received instruction on the safe use of the appliance and on the potential resulting hazards. Do not
allow children to play with the appliance. Do not allow unsupervised children to clean the appliance or to
perform maintenance tasks intended to be carried out by users.
▶ Store tools in a secure place when not in use. When not in use, tools must be stored in a dry, high place
or locked away out of reach of children.
▶ Ensure that the tool and the AC adapter do not present an obstacle that could lead to a risk of tripping
or personal injury.
▶ Do not expose the supply cords to heat, oil or sharp edges.
▶ Never operate the appliance when it is dirty or wet. Dust (especially dust from conductive materials)
or dampness adhering to the surface of the appliance may, under unfavorable conditions, lead to
electric shock.
▶ Remove the battery if the tool is to remain unused for a long period of time.
▶ Under abusive conditions, liquid may be ejected from the battery. Avoid contact with the liquid. If contact
accidentally occurs, flush with water. If the liquid contacts the eyes, also seek medical attention. Liquid
ejected from the battery may cause skin irritation or burns.
▶ Have the electric tool repaired only by a qualified specialist using only genuine Hilti spare parts. The
safety of the electric tool can thus be maintained.
▶ Do not touch the supply cord or extension cord if it is damaged while you are working. Disconnect the
supply cord plug from the power outlet. Damaged supply cords and extension cords present a risk of
electric shock.
Printed: 20.03.2017 | Doc-Nr: PUB / 5070470 / 000 / 04
English 3
Electrical
▶ Although the device complies with the strict requirements of the applicable directives, Hilti cannot
entirely rule out the possibility of interference to the device caused by powerful electromagnetic radiation,
possibly leading to incorrect operation.
▶ Use the battery charger only inside dry rooms. Water entering an electric appliance will increase the risk
of electric shock.
▶ When the battery is not in use, keep it away from other metal objects such as paper clips, coins, keys,
nails, screws, or other small metal objects that could cause bridging between the terminals. A short
circuit between the contacts may result in burning injuries or fire.
▶ Check the tool and batteries for damage before use after long periods of storage.
▶ Never continue to use or attempt to charge damaged batteries, e.g. batteries with cracks, broken parts,
bent or pushed-in / pulled-out contacts).
▶ The plug on the supply cord of the electric tool must match the power outlet. Do not change the plug
in any way. Do not use adapter plugs with earthed (grounded) electric tools. Unmodified plugs and
matching outlets reduce risk of electric shock.
▶ Use the battery charger only inside dry rooms. Water entering an electric appliance will increase the risk
of electric shock.
Cleaning and drying the tool
▶ Clean the tool with a clean, soft cloth.
▶ Maintain the appliance carefully. Check to ensure that no parts are broken or damaged in such a way
that the appliance might no longer function correctly. Have damaged parts repaired before using the
appliance.
▶ Do not abuse the cord. Never use the cord to carry or hang up the electric tool or to pull the plug out
of the power outlet. Keep the cord well away from heat, oil, sharp edges and moving parts. Damaged
cords increase the risk of electric shock.
2.2 Use and care of battery-powered tools
▶ Use only the Hilti batteries specified for use with this product.
▶ Observe the special guidelines applicable to the transport, storage and use of Li-ion batteries.
▶ Check that the product is switched off before fitting the battery.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 75°C
(167°F).
▶ Do not attempt to charge or continue to use damaged batteries.
▶ If the battery is too hot to touch it may be defective. In this case, place the tool in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. Contact Hilti Service after the battery has cooled down.
Printed: 20.03.2017 | Doc-Nr: PUB / 5070470 / 000 / 04
Loading...