Harman Kardon DVD28 SERVICE MANUAL

Download

Page 1

harman/kardon

DVD 26 and 28/230 Service Manual

Page 1 of 76

harman/kardon Service Manual

DVD 26/230 DVD 28/230

DVD players (technically identical to DVD 29 and DVD 37)

ESD PRECAUTIONS 2 SERVICING PRECAUTIONS 3 OWNER’S MANUAL OM TABLE OF CONTEN REMOTE C FEATURES FRONT PANEL CONTROLS 12 FRONT PANEL DISPLAY 13 REAR PANEL CONNECTIONS 14 SETUP A TROUBLESHOOTING GUIDE 18

ONTRO

D CONNECTIONS

FRONT PAGE 5

L FUNCTI

ONS 7

Released EU2010 Harman Consumer Group, Inc. Rev 0, 09/2010 8500 Balboa Boulevard. Northridge, California 91329

CONTENTS

BASIC SPECIFICATIONS 19 PACKAGE LIST AND PARTS 24 DISASSEMBLY EXPLODED VIEW 26 ELECTRICAL PARTS LIST 27 SEMICONDUCTOR PINOUTS 46 PCB DRAWINGS BLOCK DIAGRAM WIRING SCHEMATIC DIAGRAMS 73-76

DIAGRAM

Page 2

harman/kardon

DVD 26 and 28/230 Service Manual

Page 2 of 76

ESD PRECAUTIONS

Electrostatically Sensitive Devices (ESD)

Some semiconductor (solid state) devices can be damaged easily by static electricity . Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir cuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity .

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur face such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly .

3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESD devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges suf ficient to damage ESD devices.

6. Do not remove a replacement ESD device from its protective package until immediately before you are ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials).

7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will by installed.

CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL

OTHER SAFETY PRECAUTIONS.

8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gen erate static electricity sufficient to damage an ESD device).

Page 3

SERVICING PRECAUTIONS

NOTES REGARDING HANDLING OF THE PICK-UP

1. Notes for transport and storage

1) The pick-up should always be left in its conductive bag until immediately prior to use.

2) The pick-up should never be subjected to external pressure or impact.

2. Repair notes

1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.

2) The pick-up should always be handled correctly and carefully , taking care to avoid external pressure and impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or damage to the printed-circuit board.

3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason the adjustment point and installation screws should absolutely never be touched.

4) Laser beams may damage the eyes! Absolutely never permit laser beams to enter the eyes! Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.

5) Cleaning the lens surface If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot ton swab should be used, taking care not to distort this.

6) Never attempt to disassemble the pick-up. Spring by excess pressure. If the lens is extremely dirty , apply isopropyl alcohol to the cotton swab. (Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.

Storage in conductive bag

NEVER look directly at the laser beam, and don’t let contact fingers or other exposed skin.

Magnet

How to hold the pick-up

Conductive Sheet

Cotton swab

Pressure

Drop impact

harman/kardon

DVD 26 and 28/230 Service Manual

Page 3 of 76

Page 4

NOTES REGARDING COMPACT DISC PLAYER REPAIRS

1. Preparations

1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components are sensitive to, and easily af fected by, static electricity. If such static electricity is high voltage, components can be damaged, and for that reason components should be handled with care.

2) The pick-up is composed of many optical components and other high-precision components. Care must be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong

magnetism is present, or where there is excessive dust.

2. Notes for repair

1) Before replacing a component part, first disconnect the power supply lead wire from the unit

2) All equipment, measuring instruments and tools must be grounded.

3) The workbench should be covered with a conductive sheet and grounded. When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is because there is the possibility of damage by static electricity .)

4) To prevent AC leakage, the metal part of the soldering iron should be grounded.

5) Workers should be grounded by an armband (1M Ω)

6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent static electricity changes in the clothing to escape from the armband.

7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.

Resistor (1 Mohm)

Conductive Sheet

Resistor (1 Mohm)

Armband

harman/kardon

DVD 26 and 28/230 Service Manual

Page 4 of 76

Page 5

AVR/DVD System

harman/kardon

DVD 26 and 28/230 Service Manual

Page 5 of 76

This owner's manual covers any combination of AVR 139, AVR 141, DVD 26 and DVD 28.

AVR Audio/Video Receiver DVD Digital Versatile Disc Player

OWNER’S MANUAL

ENGLISH

Page 6

Table of Contents

harman/kardon

DVD 26 and 28/230 Service Manual

Page 6 of 76

3 Safety Information 3 Unpacking 4 Remote Control Functions AVR 8 Front Panel Controls 10 Rear Panel Connections 12 Installation and Connections 12 Audio Equipment Connections 12 Video Equipment Connections 13 HDMI Connections 14 System Configuration 14 First Turn On 14 Settings to be Made With Each Input Used 14 Input Setup 14 Speaker Setup 15 Surround Setup 15 Configuring the Surround Off

(Stereo) Modes

15 Stereo-Direct (Bypass) Mode 16 Stereo Digital Mode 16 Delay Settings 16 Night Mode Settings 16 Output Level Adjustment 18 Operation 18 Basic Operation 18 Source Selection 18 Controls and Use of Headphones 18 Surround Mode Selection 19 Digital Audio Playback 20 Selecting a Digital Source 20 Digital Status 20 Surround Mode Types 21 Night Mode 21 Tape Recording 21 Output Level Trim Adjustment 21 6-Channel Direct Input 21 Display Brightness 22 Memory Backup 22 Tuner Operation 22 RDS Operation 24 Troubleshooting Guide 24 Processor Reset 25 Technical Specifications AVR

DVD 26 Terminology 27 Features, Packing List 28 Front Panel Controls 29 Front Panel Information Display 30 Rear Panel Connections 31 Setup and Connections 31 Connecting to a TV Only 32 to a Dolby Digital/DTS Amplifier/Receiver 33 Digital Audio Connections 34 Playback Basics 34 Basic Play 34 Playback Features 35 About DivX Movie Files 36 System Set-up

DECLARATION OF CONFORMITY

We, Harman Consumer Group International

2, route de Tours F-72500 Château-du-Loir France

declare in own responsibility, that the product described in this owners manual is in compliance with technical standards:

EN55013(2001) & + A2(2006) EN55020(2002) & + A2(2005) EN60065:2002 EN61000-3-2(2000)+A2(2005) EN61000-3-3 (1995)+A1(2001)+A2(2005) EN61000-4-2(1995) & + A1(1998) & + A2(2001) EN61000-4-3(2002) & + A1(2002) EN61000-4-4(2004)

Jurjen Amsterdam Harman Consumer Group Inc. 03/09

36 System Defaults 36 Set Up Menu 36 System Settings 37 Audio Settings 38 Audio Adjustments Submenu 39 Video Settings 40 Test Screen 40 Test Screen 40 TV Picture Adjustment 41 Player Menu 41 Using the Player Information Menu 41 Using the On-Screen Status Display 42 CD Playback 44 MP3, Windows Media and JPEG Playback 46 Troubleshooting Guide 47 Technical Specifications DVD

TABLE OF CONTENTS

Typographical Conventions

In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.

Example – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

ExamplE

– (OCR type) indicates a message that is visible on the front-panel information display

– (number in a square) indicates a specific front-panel control

– (number in a circle) indicates a rear-panel connection

– (number in an oval) indicates a button or indicator on the remote.

Page 7

0 3 4

F H

































I J L

harman/kardon

DVD 26 and 28/230 Service Manual

Page 7 of 76

Remote Control Functions for Receiver and DVD Player System

Power On Button

Not active

IR Transmitter Window

Power Off Button

Mute

Input Selectors

6-Channel Direct Input

Volume Up/Down

HD Mode Selector

Speaker Select/Setup

OK Button

Delay/Status Button

Memory/Angle Button

Clear Button

Preset Up/Down

RDS Select/Info Button

Playlist

A-B

DTS Neo:6 Mode Selector

Stereo Mode Selector

Logic 7 Selector

Dim Button

Transport Buttons

Skip Up/Down Buttons (DWN)/(UP)

Night Mode

DTS Digital Mode Selector

Dolby Mode Selector

Repeat

Random

Tone Mode/Progressive Scan/Interlaced

Button

Tuning Up/Down

Direct Button

Tuner Mode/Zoom

Numeric Keys

Digital Select/Audio Mode

Navigation Buttons

Channel Select /Disc Menu Button

V.OFF/Test Button

Surround Mode Selector/Program Down/

Subtitle Button

Sleep/Program Up/Audio Select Button

Title

AM/FM Tuner Select

AVR Selector

REMOTE CONTROL FUNCTIONS

Page 8

Remote Control Functions, common for AVR and DVD

harman/kardon

DVD 26 and 28/230 Service Manual

Page 8 of 76

IMPORTANT NOTE: The combined AVR and DVD remote has some buttons that perform different functions. If you press the AVR Button of functions is active, identical to the functions for buttons CD, Tape, Video 1/2/3. If you press the DVD/ HDMI1 Button their function as indicated above the button itself, and explained below. Refer to the function table for an overview of functions in both modes. NOTE that pressing the HDMI1 and DVD Buttons 5 activate the alternative commands as seen in the Function List on page 7.

Power On Button: Press this button to turn on the power to the AVR or the DVD selected by pressing either the AVR or the DVD/HDMI1 Button

This indicator is not active.

IR Transmitter Window: Point this window towards the AVR when pressing buttons on the remote to make certain that infrared commands are properly received.

Power Off Button: Press this button to place the AVR or a selected device unit in the Standby mode. If held for more than 3 seconds, both the AVR and the DVD switch to Standby.

Mute: Press this button to momentarily silence the AVR or TV set being controlled, depending on which device has been selected.

Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR. Finally, the DVD/HDMI1 Button will switch the double-function remote buttons to their DVD functions. After pressing the DVD/HDMI1 Button, you must press the AVR Selector button

again to operate all the AVR’s functions with the remote. Note that pressing the DVD Button switches on BOTH the AVR and the DVD, whereas pressing the AVR Button just switches on the AVR.

6-Channel Direct Input: Press this button to select the component connected to the 6-Channel Direct Input wish to use the Six Channel Direct Input in conjunction with a video source, you must first select the video source by pressing one of the Input Selectors Then press this button to choose the 6-Channel Direct Input

Volume Up/Down: Press these buttons to raise or lower the system volume.

, some of the buttons change

as the audio. Note that when you

as the audio source.

, one set

HD Mode Selector (DVD): When the DVD

player is connected to a video display using the HDMI

Output indicating the highest video resolution it is capable of handling, and the DVD automatically sets the video output to match it. Pressing this button allows you to manually change the output resolution, with your selection indicated by the Video Output Indicators

The DVD will not allow you to select a resolution beyond the capabilities of your display, and if you try to do so, an on-screen error message will appear to alert you to the selection of an incompatible video format. Changes made with this button remain active until the DVD or the display is turned off. When either is turned off, and then on again, the DVD will revert to the default setting transmitted by the display.

to begin the process of configuring the AVR’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the channel you wish to set up. Press the OK button and then select the speaker type (see page 14 for more information.)

For DVD: Press this button to use the DVD’s on-screen menu system to adjust the player’s configuration settings. Note that the Info Button pressed to access the DVD’s Information menu to obtain detailed disc information, and to configure the playback mode of the disc.

into the AVR’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

begin the process for setting the delay times used by the AVR when processing surround sound. After pressing this button, the delay times are entered by pressing the OK button buttons button again to complete the process. (See page 16 for more information.)

For DVD: Press while a disc is playing to view banner display. Use the ARROW buttons to move through the different features in the Banner Display. When

a symbol is highlighted, press OK on the remote to select it.

, the display sends information to the DVD

Speaker Select/Setup: Press this button

buttons Z to select the

OK Button: This button is used to enter settings

Delay/Status Button: Press this button to

and then using the

to change the setting. Press the Set

must be

Memory/Angle Button: Press this button to enter a radio station into the AVR’s preset memory. Two underline indicators will flash at the right side of the Main Information Display have five seconds to enter a preset memory location using the Numeric Keys information.)

For DVD: Press to access various camera angles on a DVD (If the DVD contains multiple camera angles) or to rotate JPEG images.

Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR’s memory. When CD or DVD is selected using the Input Selector button these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD).

RDS Select/Info (DVD) Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner. (See page 22 for more information on RDS).

For DVD: Press for detailed informations on the disc playing (Video/Audio Bit rate, Movie aspect ratio and others), and for current player settings made. Note that the unit doesn’t react on any transport button as long as the info menu is displayed. Press again to remove information from screen.

Playlist (DVD): Press this button to change the playback order of the disc.

A-B (DVD): Press to select section A-B and to play repeatedly.

DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-channel surround field from two-channel program material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode in the following order:

. (See page 22 for more

, you then

ENGLISH

REMOTE CONTROL FUNCTIONS

Page 9

Remote Control Functions, common for AVR and DVD

harman/kardon

DVD 26 and 28/230 Service Manual

Page 9 of 76

Stereo Mode Selector: Press this button to select a stereo playback mode. When the button is pressed so that the Main Information Display

DSp SURR OFF

appears in

, the AVR will operate in a bypass mode with true fully analog, two-channel left/right stereo mode with no surround processing or bass management as opposed to other modes where digital processing is used. When the button is pressed so that in the Main Information Display

SURROUND OFF

, you may

appears

enjoy a two-channel presentation of the sound along with the benefits of bass management. When the button is pressed so that

5 CH STEREO

appears, the stereo signal is routed to all five speakers, if installed.(See page 15 for more information on stereo playback modes).

Logic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 19 for the available Logic 7 options).

Dim Button: Press this button to activate the Dimmer function, which reduces the brightness of the front panel display, or turn it off entirely. The first press of the button shows the default state, which is full brightness by indicating Main Information Display

VFD FUll

. Press the button

in the

again within five seconds to reduce the brightness by 50%, as indicated by

VFD HalF

. Press the button again within five seconds and the main display will go completely dark. Note that this setting is temporary; the display will always return to full brightness when the AVR is turned on. In addition,both the Power Indicator

and the blue accent lighting inside the volume control will always remain at full brightness regardless of the setting. This is to remind you that the AVR is still turned on.

Transport Buttons: These buttons operate the

DVD player.

Skip Up/Down Buttons (DVD):

(DWN): Press to go to beginning of current track. Press again quickly to go to beginning of previous track. After pressing the PAUSE button, each press of this button will move the image in reverse frame by frame.

(UP): Press to go to beginning of next track. After pressing the PAUSE

button, each press of this button

will move the image forwards frame by frame.

Night Mode: Press this button to activate the Night mode. This mode is available only with Dolby Digital encoded digital sources, and it preserves dialog (center channel) intelligibilty at low volume levels (See page 16 for more information).

DTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropriate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting.

Dolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing.

Repeat (DVD): Each press of this button changes the playback mode to repeat a chapter or track or the entire disc. A repeat icon will appear in the upper right corner of the screen indicating the current repeat mode. If the Player Information Screen is active, the changes will be displayed on screen.

Random (DVD): Press for RANDOM playback in random order.

Tone Mode/Progressive Scan/Interlaced Button: Pressing this button enables or disables the

Bass and Treble tone controls. When the button is pressed so that the words Main Information Display

TONE IN

the Bass and Treble controls will affect the output signals. When the button is pressed so that the words

TONE OUT

Display

appear in the Main Information

, the output signal will be “flat,” without

any bass or treble alteration.

For DVD: Press this button to change the resolution of the Component Video Output between standard definition and progressive definition (PAL interlaced and PAL progressive; NTSC interlaced and NTSC progressive). The new setting will become effective after quitting the Setup menu.

Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode

has been pressed or the Band button 8 on the front panel was held pressed so that in the Main Information Display either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the Information Display

maNUal

appears in the Main

, pressing these buttons will tune stations in single-step increments. (See page 22 for more information).

Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys a station (See page 22 for more information on the tuner).

appear in the

, the settings of

button

aUTO

appears

, pressing

to select

Tuner Mode/Zoom: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so

maNUal

Display

appears in the Main Information

, pressing the Tuning buttons

will move the frequency up or down in single-step increments. When the FM band is in use and appears in the Main Information Display

aUTO

, pressing this button will change to monaural reception making even week stations audible. (See page 22 for more information.)

When a DVD or VCD is playing, press this button to zoom the picture so that it is enlarged. There are 4 steps to the zoom function, each progressively larger. Press through each of the zoom stages to return to a normal picture.

Numeric Keys: These buttons serve as a ten- button numeric keypad to enter tuner preset positions. For DVD play you may enter track numbers directly, followed by OK to go to the track.

Digital Select/Audio Mode: Press this button to assign one of the digital inputs

4G9L to a

source. (See page 12 for more information on using digital inputs.) Audio Mode: When operating the DVD, press this button to switch between Audio Modes.

Navigation Buttons: These are multi-purpose buttons. They will be used most frequently to select a surround mode. These buttons are also used to increase or decrease output levels when configuring the unit, to select speaker configuration or to select the digital inputs.

Channel Select /Disc Menu Button: This button is used to start the process of setting the AVR’s output levels with an external source. Once this button is pressed, use the

buttons Z to select the

channel being adjusted, then press the OK button

, followed by the KL buttons again, to change the level setting. (See page 21 for more information.)

DVD Disc Menu: Displays the actual DVD Disc Menu on the TV screen in play mode. When playing discs with JPEG images, pressing this button will access the thumbnails.

V.OFF/Test Button: Press to turn off video output for improved performance from audio-only discs. Press again to restore video output.

Tone: Press this button to begin the sequence used to calibrate the AVR’s output levels. (See page 16 for more information on calibrating the AVR).

REMOTE CONTROL FUNCTIONS

Page 10

Remote Control Functions, common for AVR and DVD

harman/kardon

DVD 26 and 28/230 Service Manual

Page 10 of 76

Surround Mode Selector/Program Down/

Subtitle Button: Press this button to begin the

process of changing the surround mode. After the button has been pressed, use the

buttons Z to select the desired surround mode. (See page 18 for more information).

When a DVD is playing, press to select a subtitle language or to turn subtitles off.

Note: Due to the variations in how DVD discs are authored, the subtitle languages selected with the Subtitle Button may not accurately reflect the actual languages available on the disc. It is recommended that subtitles be selected using the disc’s menu.

Sleep/Program Up>/Audio Select Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the AVR will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:

Hold the button pressed for two seconds to turn off the Sleep mode setting.

Note that this button is also used to change channels on your TV, VCR and SAT receiver when selected.

DVD: Press to access various audio languages on a DVD (If the DVD contains multiple audio streams).

Title: When a disc is playing, press to make the player go back to the first section of the disc. If you are playing a DVD-Audio disc that contains other formats the DVD is capable of playing, such as linear PCM or Dolby Digital 5.1, pressing this button may enable you to switch playback from one audio format to another.

AM/FM Tuner Select: Press this button to select the AVR’s tuner as the listening choice. Pressing this button when the tuner is in use will select between the AM and FM bands.

AVR Selector: Pressing this button will switch the remote so that it will operate the AVR’s functions. If the AVR is in the Standby mode, it will also turn the AVR on.

Function List

Button Name Power ON Power OFF Power Off (press and release) Power Off (press and release)

Mute Mute Mute(AVR) AVR DVD DVD DVD(AVR) VID1 VID 1 VID 1(AVR) HDMI1 HDMI 1 HDMI 1(AVR) AM/FM CD CD CD(AVR) VID2 VID 2 VID 2(AVR) HDMI2 HDMI 2 HDMI 2(AVR) AUX AU X AUX(AVR) TAPE TAPE TAPE(AVR) VID3 VID 3 VID 3(AVR) HDMI3 HDMI 3 HDMI 3(AVR) SLEEP / AUDIO TITLE Title 6CH 6CH 6CH(AVR) VOL Up Vol Up Vol Up(AVR) SURR. / SUBT. TEST / V.OFF Test Tone Video Off HD-M HD Mode VOL Down Vol Down Vol Down(AVR) CH. / DISC MENU SPKR / SETUP Level+/Up Level+/Up Up

M Left Left

Left OK SET Enter

N Right Right

Right Level-/Down DIGITAL / AUDIO MODE DELAY / STATUS Delay 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 TUN-M / ZOOM Tuner Mode Zoom 9 9 9 0 0 0 MEM / ANGLE Memory Angle TUNING Up Tuning Up DIRECT Direct Tuning CLEAR Clear Clear PRESET Up Preset Up TUNING Down Tuning Down TONE / P/I Tone Mode P/I RDS / INFO PRESET Down Preset Down RANDOM Random Play REPEAT Repeat Play A-B PLAYLIST Playlist DOLBY SUR DTS SUR DTS Surround DTS Surround(AVR) DTS NEO:6 DTS NEO:6 DTS NEO:6(AVR) NIGHT Night Mode Night(AVR) LOGIC 7 STEREO Stereo Stereo(AVR) SKIP DOWN Skip Down(DVD) Skip Down SKIP UP Skip Up(DVD) Skip Up DIM Dimmer Dimmer

G) Rew(DVD) Rew

Rew(

B) Play(DVD) Play

Play(

H) FF(DVD) FF

FF( Open/Close Open/Close(DVD) Open/Close Stop Stop(DVD) Stop Pause Pause(DVD) Pause

HK AVR Remote Command AVR/TAPE/CD/AUX/VID1/VID2/VID3/HDMI2/HDMI3

Power On Power On

Power Off (press and hold) Power Off (press and hold)

AVR Power On AVR(AVR)

AM/FM AM/FM(AVR)

Sleep Audio

Surround Mode Subtitle

Channel Select Disc Menu Speaker Select Setup

Level-/Down Down Digital Select Audio Mode

RDS Info

Dolby Surround Dolby Surround(AVR)

Logic7 Logic7(AVR)

HK DVD Remote Command DVD/HDMI1

Status

Slow Up

Slow Down

A-B Repeat Play

ENGLISH

REMOTE CONTROL FUNCTIONS

Page 11

Features

harman/kardon

DVD 26 and 28/230 Service Manual

Page 11 of 76

High quality video

High Definition Multimedia Interface (HDMI) for a • single wire, digital connection to your HD-Ready screen.

Advanced sophisticated 10-bit MPEG-2 video

• decoding circuits.

Direct RGB output via SCART (selectable) for • optimum video performance. SCART connector also configurable for Composite Video output.

•

Test screen videos available for testing video performance and setup.

Pure PAL with NTSC disc due to true NTSC/PAL • conversion.

•

Dual-layer compatibility for extended play DVD.

Progressive Scan component video ouputs (NTSC • and PAL)

Playback of JPEG image files •

High quality digital audio

Built-in DVD-Audio decoder for improved musical • realism.

By connecting a DTS (Digital Theater Systems) or a • Dolby Digital decoder, you can enjoy high quality

5.1 digital surround sound from DTS or Dolby Digital discs.

•

With linear PCM audio at 16-24 bits and

•

44-96 kHz (also on digital output, see table page

33), audio quality exceeding that of CD becomes possible.

Optical and coaxial digital audio output. •

Many convenient features

On-Screen Menu lcons for disc information or • player information and access to many major functions of this unit.

Subtitles may be displayed in one of numerous • languages*.

•

The multi-angle function allows you to choose the viewing angle of scenes which were shot from a number of different angles (Limited to DVD’s recorded with multiple camera angles.)

•

Multiple options for dialog language and soundtrack selection (limited to DVD’s recorded with multiple dialog languages or soundtracks).

•

Intuitive menu operating system.

•

4 step Zoom during play and pause.

Backlit, ergonomically designed remote control. •

Future software upgrades accessible via Internet. • (See information below.)

* The number of languages recorded depends on the software.

Compatible with CD as well as DVD

The DVD will play any conventional Audio CD or • recordable (CD-R) or erasable CD (CD-RW), MP3, WMA (v8) or any DivX or VCD or DVD/Video with the region code 0 or 2.

Disc formats supported by this player

The unit can play the following disc formats (8 cm and 12 cm size):

DVD-AUDIO • DVD

• DVD-R

• DVD-RW

• DVD+R

• DVD+RW

• CD

• CD-R

• CD-RW

• VCD

• WMA (v8)

•

NOTE: Due to differences in the format of certain discs, it is possible that some discs may include a mix of features that are not compatible with the DVD. Similarly, although the DVD is capable of a wide range of features, not all discs include every capability of the DVD system. For example, although the DVD is compatible with multi-angle discs, that feature is only possible when the disc is specially encoded for multi pleangle play. In addition, the DVD is capable of playing back both Dolby Digital and DTS soundtracks, but the number and types of tracks available will vary from disc to disc. To make certain that a specific feature or soundtrack option is available, please check the options noted on the disc jacket.

■

Playback capability for CD-R, CD-RW, WMA, JPEG, MP3, DivX, VCD/SVCD, DVD-R, DVD+R, DVD-RW and DVD+RW discs may vary due to variations in the quality of the disc and the recorder used to create the disc.

■

The DVD is compatible with most discs recorded with files encoded using MP3 or Windows Media 9, as well as JPEG still images. However, note that variations in the encoder or codec used and the bit rate of the encoding may affect the DVD’s ability to play back a specific disc. As a result, we cannot guarantee complete compatibility with all encoders and versions of the codecs. For best results, we recommend that MP3 files be encoded at bit rates ranging between 32kbps and 320kbps. WMA files should be encoded at bit rates between 64kbps and 320kbps. Although the DVD is capable of playing some WMA 9 files, not all features of version 9 are supported. JPEG files should contain no more than 5 megapixels, and the file size should be no larger than 5Mb.

The DVD will NOT play the following:

DVD discs with a Region Code other than 2 •

DVD-ROM data discs •

DVD-RAM discs

•

CD-I discs

•

CD-G discs

•

SVCD discs •

Kodak Photo CD™ discs (Kodak Picture CD discs,

• available to consumers, may be viewed using the DVD).

Discs intended for use in video game consoles

•

Discs recorded in the “VR” mode or at any speed

• other than “SP”

High-definition optical discs such as WMVHD, • HD-DVD and Blu-ray

Upgradeability via Internet

The ”firmware” controlling the functionality of the Harman Kardon DVD is fully upgradeable. In the event of future improvements to its operations and features, it will be possible to download firmware upgrades from www.harmankardon.com/International

All you have to do is create a CD-R with the data and insert it in the DVD for an automatic upgrade.

Packing List

1 Harman Kardon DVD Player

1 A/V cable for stereo analog audio and

composite video

1 HDMI cable

NOTE: This player is designed and manufactured for compatibility with Region Management Information that is encoded on most DVD discs. This player is designed only for playback of discs with Region Code 2, or for discs that do not contain Region Code infor mation. If there is any other Region Code on a disc, that disc will not play on the DVD.

CLASS 1

LASER PRODUCT

ENGLISH

FEATURES

Page 12

1 3 4 5 6 7 8



Front Panel Controls

harman/kardon

DVD 26 and 28/230 Service Manual

Page 12 of 76

Main Information Display

Power On/Off (Standby)

Open/Close

3 4 5

Play

Pause

Stop

Skip/Search (Previous)

Skip/Search (Next)

Dimmer

Main Information Display: This display delivers messages and status indications to help you operate the DVD player.

Power On/Off (Standby): Press the button once to turn the DVD player on, press it again to put the unit in the Standby mode.

Open/Close: Press this button to open or close the Disc Tray.

Play: Press to initiate playback or to resume playback after Pause has been pressed.

Pause: Press this button to momentarily pause playback. To resume playback, press the button again. If a DVD is playing, action will freeze and a still picture will be displayed when the button is pressed.

Stop: Press this button once to place the disc in the Resume mode, which means that playback will stop, but as long as the tray is not opened or the disc changed, DVD playback will continue from the same point on the disc when the Play Button is pressed again. Resume will also work if the unit was turned off. To stop a disc and have play start from the beginning, press the button twice.

Skip/Search (Previous): Press this button to move backward through the music tracks on a CD disc or the chapters on a DVD disc. Keep the button pressed to search backwards at one of the available speeds.

Skip/Search (Next): Press to move forward through the music tracks on a CD or the chapters on a DVD disc. Keep the button pressed to search forwards at one of the available speeds.

Dimmer: Press this button to reduce the brightness of the Information Display by 50% or to turn the display off completely in the following order: FULL BRIGHTNESS ‘ HALF BRIGHTNESS ‘ OFF ‘ FULL BRIGHTNESS.

FRONT PANEL CONTROLS

Page 13

Front Panel Information Display

harman/kardon

DVD 26 and 28/230 Service Manual

Page 13 of 76

Disc Type Indicators

Playback-Mode Indicators

Audio Bitstream Indicators

Chapter/Track Number Indicators

Time Indicators

Title Indicators

V-OFF Indicator

Repeat Indicators

VCD Playback Control Indicator

Random Indicator

A-B Repeat Indicator

Program Indicator

Angle Indicator

Parental Lock Indicator

Video Output Indicators

ENGLISH

Disc Type Indicators: The CD, DVD, DVD-Audio, VCD, MP3, WMA or JPEG indicator will illuminate to show the type of disc currently being played.

Playback-Mode Indicators: These indicators light to show the current playback mode:

Lights when a disc is playing in the normal mode

Lights when the disc is in the Fast Search Forward mode. The on-screen banner display indicates the selected speed (x2, x4, x8, x20, x100).

Lights when the disc is paused.

Lights when the disc is in the Fast Search Reverse mode. The on-screen banner display indicates the selected speed (x2, x4, x8, x20, x100).

Audio Bitstream Indicators: When a Dolby® Digital, DTS® or linear PCM digital audio signal is present on the disc, one of these indicators will light. DVD-Audio, MP3 and WMA bitstreams will be indicated by the Disc Type Indicator

Chapter/Track Number Indicators: When a

DVD disc is playing, these two positions in the display will show the current chapter. When a CD disc is playing they will show the current track number.

Time Indicators: These positions in the indicator will show the running time of a DVD in play. When a CD is playing, these indicators will show the current track time, time remaining in the current track, or the total remaining time on the disc.

NOTE: The Indicators

DEF

will also display

text messages about the DVD’s status, including

lOaDING pOWER OFF DISC ERROR

when a disc is loading,

when the unit is turned off, and

when a disc not compatible with the

DVD is put into the play position.

Title Indicators: These two positions in the display will show the current title number when a DVD disc is playing.

V-OFF Indicator: This indicator lights when the unit's video output has been turned off by pressing the V-OFF button on the remote control.

Repeat Indicators: These indicators light when any of the Repeat functions are in use.

VCD Playback Control Indicator: This indicator lights when the playback control function is turned on with VCDs.

Random Indicator: This indicator lights when the unit is in the Random Play mode.

A-B Repeat Indicator: This indicator lights when a specific passage for repeat playback has been selected.

Program Indicator: This indicator lights when the programming functions are in use.

Angle Indicator: This indicator blinks when alternative viewing angles are available on the DVD currently playing.

Parental Lock Indicator: This indicator lights when the parental-lock system is engaged in order to prevent anyone from changing the rating level without a code.

Video Output Indicators: When the DVD is connected to a video display using the HDMI

Output

, the display sends information to the DVD indicating the highest video resolution it is capable of handling, and the DVD automatically sets the video output to match it. That resolution is displayed here. You may use the HD Mode Selector W to manually select a lower video output resolution.

FRONT PANEL INFORMATION DISPLAY

Page 14

 







Rear Panel Connections

harman/kardon

DVD 26 and 28/230 Service Manual

Page 14 of 76

Optical Digital Output

Coaxial Digital Output

AC Power Cord

Composite Video Output

Optical Digital Output: Connect this jack to the optical digital input of an A/V receiver or surround processor for Dolby Digital, DTS or PCM audio playback.

Coaxial Digital Output: Connect this jack to the coaxial digital input of an A/V receiver or surround processor for Dolby Digital, DTS or PCM audio playback.

NOTE: The coaxial digital output should only be connected to a digital input. Even though it is the same RCA-type connector as standard analog audio connections, DO NOT connect it to a conventional analog input jack.

Connect either the Optical Digital Audio Output

or the Coaxial Digital Audio Output 1 to a corresponding digital audio input on your receiver or processor, but not both.

AC Power Cord: Connect this plug to an AC outlet. If the outlet is controlled by a switch, make certain that it is in the ON position.

Composite Video Output: Connect this jack to the video input on a television or video projector, or to a video input on an A/V receiver or processor if you are using that type of device for video input switching.

S-Video Output: Connect this jack to the S-Video input on a television or video projector, or to an S-Video input on an A/V receiver or processor if you are using that type of device for S-Video input switching. Please note that the AVR Receiver in your system does not accept S-Video signals. Use composite or component connection instead.

Component Video Outputs: These outputs carry the component video signals for connection to display monitors with component video inputs. For standard analog TV's or projectors with inputs marked Y/Pr/Pb or Y/Cr/Cb, connect these outputs to the corresponding inputs. If you have a high-definition television or projector that is compatible with high scan rate progressive video, connect these jacks to the “HD Component” inputs. Note that if you are using a progressive scan display device, then ”Progressive” must be selected in the Video Set-up Menu in order

S-Video Output

Component Video Outputs

Scart TV Output

Remote Control Output

to take advantage of the progressive scan circuitry. See page 39 for more information on progressive scan video.

IMPORTANT

standard composite video inputs.

SCART OUT (TV): If your TV has a SCART socket, you can connect a SCART cable to your TV and to your DVD Player for improved video quality. The SCART cable carries both audio and video. You can select Composite Video or RGB video for that SCART connector’s video output signal.

Remote Control Output: Connect this jack to the infrared (IR) input jack of another compatible Harman Kardon remote controlled product to have the built-in Remote Sensor on the DVD provide IR signals to other compatible products.

Remote Control Input: Connect the output of a remote infrared sensor, or the remote control output of another compatible Harman Kardon product, to this jack. This will enable the remote control to operate even when the front panel Remote Sensor on the DVD is blocked. This jack may also be used with compatible IR remote control-based automation systems.

Analog Audio Output: Connect these jacks to an audio input on an A/V receiver or surround processor for analog audio playback.

HDMI Output: If you have an HDMI-compatible receiver or video display device, connect this output to an HDMI input on the receiver or video display for the highest-quality uncompressed digital audio and video available. Even if your receiver is not capable of processing audio in the HDMI format, you may still experience the superb reproduction of HDMI video.

The AVR Receiver in your system can switch between three HDMI inputs and send the video signal to your screen from its HDMI Output. No audio processing takes place in the Receiver via HDMI, so no sound will be heard if only HDMI is connected. The Audio information is best transmitted from the DVD Player's Coaxial Digital Output to the AVR Receiver's Coaxial Digital Input. Alternatively, you may use the Optical Digital Connection, or the Analog Audio connections.

: These jacks should NOT be connected to

Remote Control Input

Analog Audio Output

HDMI Output

6-Channel Audio Outputs

If your video display has a DVI input, you may use an optional HDMI-to-DVI cable or adapter for the connection to the display. In all cases, the video display must be HDCP-compliant in order to use the HDMI output. For best results, we do not recommend HDMI connections in excess of ten feet.

The following audio formats may be output via the HDMI connection:

Audio CD – 2-Channel PCM or 5.1-channel DTS DVD-Audio – 2-Channel PCM DVD-Video – Up to 5.1-channel Dolby Digital or DTS

Note: To hear the high-resolution surround sound recorded on DVD-Audio discs, you need to connect the 6-Channel Audio Outputs input jacks on your receiver or processor. These formats are not output digitally.

6-Channel Audio Outputs: Connect these outputs to the matching 6-channel analog audio inputs on your receiver or surround sound processor. This connection is required to listen to the multichannel tracks on DVD-Audio discs. If the disc also contains a linear PCM, Dolby Digital or DTS track, you may listen to it using the HDMI A, Optical 0 or Coaxial Digital Audio Output Audio Outputs

: You’ll find more details about all Audio/Video

Note

connections under Setup and Connections on the following pages.

to the corresponding

or the Analog

REAR PANEL CONNECTIONS

Page 15

Setup and Connections

harman/kardon

DVD 26 and 28/230 Service Manual

Page 15 of 76

Before connecting your DVD, please:

Ensure that the power switch of this unit and other ■ equipment to be connected is set to off before commencing connection.

Do not block ventilation holes of any of the

■

equipment and arrange them so that air can circulate freely.

Read through the instructions before connecting

■

other equipment.

■

Ensure that you observe the color coding when connecting audio and video cables.

ENGLISH

For the best quality, we recommend using the HDMI output. With a single cable connection between components, HDMI is able to deliver uncompressed high-definition digital video and digital audio programming. Please note that the AVR Receiver in this system does not process Audio through HDMI. Therefore, separate Audio connections must be established between DVD and AVR.

Note: If your video display has a DVI input, you may use an optional HDMI-to-DVI cable or adapter for the connection to the display. In all cases, the video display must be HDCP-compliant in order to use the HDMI output.

If your equipment is not HDMI-ready, we recommend the use of component video for higher quality pictures.

If you are using a television or video display that is compatible with high-resolution 576P video signals, make sure to use the input jacks on the video display marked “HD Component,” if available. Also, make sure to configure the display’s input settings for use with “576P” video signals. You will also need to change the scan type in the DVD’s Video Setup menu from “Interlaced” to “Progressive.” See above.

The Video output (yellow) combines the complete video signal (composite) and sends it to the TV (or to the AV Receiver) by one line only. Use the Video output, when your TV set is equipped with a Video input jack only.

The S (separate) video output connector separates the color (C) and luminance (Y) signals before transmitting them to the TV set in order to achieve a sharper picture. Use the S-video cable when connecting the player to a TV equipped with an S-video input for improved picture clarity. Never connect both outputs, Video and S-Video, to your TV, only one of them.

Most European TV´s are equipped with SCART connectors rather than with a normal video input (yellow cinch). In that case the SCART connection should be used, providing the audio signal too. Separate analog audio connections to TV are needed only if your TV is connected to the video or S-video output.

You may also use the standard S-video or composite video connection if your TV does not have component video inputs. The component and S-video outputs are not available simultaneously.

Modern audio/video receivers are capable of • connection to several video source devices, such as the DVD and a VCR, cable television set-top box, HDTV tuner or other device. The receiver is equipped with video monitor outputs for connection to your television, projector or plasma display. As you select any input source device, the receiver selects the correct video input and routes it to the correct video monitor output to your

television. It is recommended that you connect one of the video outputs from the DVD to the corresponding input on your receiver to simplify operation of your home entertainment system.

•

If connecting your DVD to another receiver capable of multiroom operation, it is recommended that you connect both the component (or HDMI) and composite video outputs of the DVD to the receiver. This enables the highest-quality picture (component video) for viewing in the main listening room, while enabling the multiroom system, if it is video-capable, to distribute the composite video signal to the remote zone. Consult the owner’s guide for your receiver to determine whether it has video multiroom capability.

Connecting to a TV Only

When using the DVD with a television but no audio receiver or processor, connect it as follows. Make the Analog Audio Connection the Video Connections (Composite Video

S-Video

, Component Video D). If your

television or video display is HDMI-capable, you only need to make the HDMI both audio and video. Remember to plug in the power cord.

and one of

connection, as it handles

To Y (green)/

Pb (blue)/

Pr (red)

To HDMI

or DVI

port on TV

E D C B A

component

video

connectors

To S-video input connectors on the TV

To video

connectors

(yellow)

on the TV

input

To analog audio

input connectors

(red/white) on the TV

To power outlet

(AC 230V/50Hz)

SETUP AND CONNECTIONS

Page 16

Setup and Connections

harman/kardon

DVD 26 and 28/230 Service Manual

Page 16 of 76

Connecting to a Receiver/Amplifier With a Dolby Digital or DTS Decoder

One of the major advantages of the DVD format is its ability to use a variety of digital audio formats for the ultimate in sonic performance. However, in order to enjoy the benefits of digital audio, you must use a receiver or processor that has digital audio decoding capabilities and make an optical or coaxial digital audio connection between the DVD and your home theater system. This simple connection is made as shown below with an optional coax or optical cable. Only one of these connections is required, and both should not be made at the same time.

In order to take advantage of the high-resolution DVD-Audio output of the DVD, you must connect the 6-Channel Audio Outputs B to the matching 6-channel inputs on your receiver or processor.

NOTES FOR ANALOG AUDIO:

•

If you wish to use the DVD as the input for a multiroom system, the Analog Audio Outputs

should be connected to the standard analog left/right DVD or CD inputs on your digital receiver or processor.

• Analog Audio Outputs

The connection from the

to the TV is optional.

When the audio signal is to be fed to an analog • receiver rather than to the TV, connect the Analog Audio Outputs

to any analog audio inputs on

your receiver or processor.

•

The analog audio connection should also be made if you wish to play high-resolution 96kHz PCM audio discs where your receiver does not support 96kHz processing.

NOTES ON VIDEO:

Note: With multiple video sources, your Audio/ ■ Video device can be used for selecting the video signal and routing it to the TV. Connect the video output of the DVD player (whatever is provided with your device) to the video input on your device and the video output of this device to your TV. For more details, see the manual of your Audio/Video amplifier/receiver.

■

Note for Analog Audio: The connection from Audio Out to the TV is optional only. Normally you’ll hear the sound from your AV-system’s speakers, so the TV volume should be completely turned down. If you plan to use your DVD player also without having to turn on your complete system, this connection must exist, then you can turn up the TV´s volume as needed.

Connecting to a Receiver

When using the DVD with an audio/video receiver or processor, connect it as follows. First, make one of the video connections (Composite Video C, Component Video input jacks on the A/V receiver, and then connect the receiver’s video monitor output to the TV. When connecting to the Receiver of your system, use HDMI for input as well as output, if your video display is so equipped. Note that your Receiver has no S-Video input jack. In addition, to benefit from the high-resolution surround sound formats recorded on DVD-Audio discs, which are not output via the HDMI connection, you will need to make the 6-Channel Audio Connection

Second, if your receiver or processor is not HDMIcapable, make either the Optical Digital Audio

Connection Connection

IMPORTANT NOTE: Make certain that any device

being connected, including the DVD, your receiver or processor and your TV or video display, is turned off whenever you make connections between products.

or HDMI H) to the video

to your receiver or processor.

or the Coaxial Digital Audio

, to the receiver or processor.

Front Speakers

(Left/Right)

Center

Speaker Subwoofer

Surround Speakers

(Left/Right)

Dolby Digital/DTS A/V Receiver or Processor

HDMI

or DVI

port

To optical

digital

audio

input

connectors

H G F E D C B A

To coaxial digital audio input connectors

To Y (green)/ Pb (blue)/ Pr (red) component video connectors

Important Notes on SCART and RGB format:

Your DVD is equipped with a SCART connector for ■ direct connection to the TV.

The SCART connector provides the video signal as ■ well as audio (stereo L/R) signals.

To view RGB video on your TV, the RGB compatible SCART connector on the TV must be used and the DVD´s TV SCART connector must be set to ”RGB”.

To S-video input connectors

The SCART connector for the TV provides the ■ composite video signal or the direct RGB signal, delivering the best video performance possible, selectable in the Setup menu.

To video input connectors (yellow)

HDMI, DVI, Component,

S-video and/or Composite video monitor outputs

To analog audio input connectors (red/white) on the TV or receiver (see above)

Note that with RGB video the color intensity cannot be adjusted with most TVs.

To 6-channel analog audio inputs on receiver

To power outlet

(AC 230V/50Hz)

When the RGB video signal is used, DVD´s ■ recorded with the NTSC format (with regional code 0 or 2) can be viewed even on non-NTSC compatible TVs.

SETUP AND CONNECTIONS

Page 17

Digital Audio Connections

harman/kardon

DVD 26 and 28/230 Service Manual

Page 17 of 76

Audio output from the unit’s optical/ coaxial digital audio output connector

Gently push the cable plug through the built-in shutter that covers the optical digital audio output and connect the cable firmly so that the configurations of both the cable and the connector match.

Sound recording

Disc

format

DVD Dolby Digital Dolby Digital bitstream

Linear PCM (48/96kHz, 16/20/24-bit)

DTS Bitstream or no output*

MPEG (2.0) MPEG bitstream (2ch) or

VCD MPEG-1

CD-DA

CD Linear PCM Linear PCM (44.1kHz

MP3 MPEG-1 Audio Layer 3)

WMA (Windows Media Audio)

* D igital Format must be selected as “ORIGINAL“

or ”PCM” respectively in Menu

Optical/coaxial digital audio output

(2-5.1ch) or PCM (2ch, 48kHz, 16-bit)††

Linear PCM (2ch) (48/96kHz, 16/20/24-bit)

linear PCM (2ch, 48kHz)

Linear PCM*

sampling)

Linear PCM (44.1–48kHz, depending on source, if digital output format selected as “Bitstream”). (48kHz if digital output format selected as “PCM”)

Linear PCM (32–48kHz)

For your reference:

Dolby Digital (AC-3) is a digital sound compression ■ technique developed by the Dolby Laboratories Licensing Corporation, supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

Linear PCM is a signal recording format used in ■ CDs. While CDs are recorded in 44.1kHz/16 bit, DVDs are recorded in 48kHz/16 bit up to 96kHz/24 bit.

If you have a Dolby Pro Logic Surround decoder ■ connected to the DVD’s analog AUDIO OUT connectors, thanks to the ”Downmix” function of the DVD you will obtain the full benefit of Pro Logic from the same DVD movies that provide full

5.1-channel Dolby Digital soundtracks, as well as from titles encoded with Dolby Surround.

The DVD is designed to digitally output 96kHz- ■ PCM audio with a 96kHz sampling rate. However, some 96kHz DVD's may include copy protection codes that do not permit digital output. For full 96kHz fidelity from these discs, use the analog outputs of the DVD.

IMPORTANT: If your surround processor/D/A converter does not support 96kHz PCM audio, you must use the DVD analog outputs for full 96kHz fidelity with these discs.

Caution for the optical/coaxial digital audio outputs:

When connecting an amplifier (with an optical/ ■ coaxial digital input ) which does not contain a Dolby Digital (AC-3) or DTS decoder, be sure to select ”PCM” as initial setting in the ”Digital Output” menu. Otherwise, any attempt to play a DVD may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

■

CD’s can be played as they would normally be played.

Note:

Some first generation DTS decoders which do not ■ support DVD-DTS interface may not work properly with the DVD/CD player.

Dolby Digital, DTS and PCM signals are passed ■ through the HDMI Output

but are not processed in the AVR Receiver in your system. Connect the Digital Audio separately besides HDMI to get sound from your system Receiver. DVD-Audio signals are not carried via the HDMI connection or the Coaxial or Optical Digital Audio Outputs. You must connect the 6-Channel Audio

Outputs

to the corresponding input jacks on your receiver or processor in order to enjoy DVDAudio materials.

Dolby Digital and DTS

Both Dolby Digital and DTS are audio formats used to record 5.1-channel audio signals onto the digital track of film. Both of these formats provide six separate channels: left, right, center, left rear, right rear, and common subwoofer. The latest 6.1-formats, Dolby Digital EX and DTS ES, even one (or two) additional "Surround Back" channel for a center between the rears.

Remember, that Dolby Digital or DTS will only play

5.1-channel sound if you’ve connected the optical or coaxial output of the DVD player to a DTS or Dolby Digital receiver or decoder and if the disc was recorded in the Dolby Digital or DTS format.

ENGLISH

DVD-Audio

The high-resolution output of DVD-Audio discs is only available as an analog signal. For that reason, it is necessary to make direct analog connections between the 6-Channel Audio Outputs the matching 6-channel inputs on your receiver or surround processor.

DIGITAL AUDIO CONNECTIONS

on the DVD and

Page 18

Troubleshooting Guide

harman/kardon

DVD 26 and 28/230 Service Manual

Page 18 of 76

SYMPTOM CAUSE SOLUTION

Unit does not turn on No AC Power Disc does not play Disc loaded improperly

No picture Intermittent connections

No sound Intermittent connections

Picture is distorted or jumps during fast forward or reverse play

Some remote buttons do not operate during DVD play; prohibited symbol appears (see below)

The OSD menu is in a foreign language Incorrect OSD language • Change the display language selection. •

symbol appears

The

Picture is displayed in the wrong aspect ratio

Remote control inoperative Weak batteries

Disc will not copy to VCR Copy protection Password not accepted. Incorrect password being used or password

• Check AC power plug and make certain any switched outlet is turned on. •

• Load disc label-side up; align the disc with the guides and place it in its •

Incorrect disc type

• Check to see that disc is CD, CD-R, CD-RW, DivX, VCD, MP3, WMA, JPEG, •

Invalid Region Code

• Use Region 2 or Open Region (0) disc only. •

• Enter password to override or change rating settings. •

Rating is above parental preset

• Check all video connections. •

• Check input selection of TV or receiver. •

Wrong input Progressive Scan output selected • Use Progressive Scan mode only with compatible TV. If needed, press the •

Video Off feature active •

• HDMI Output A is connected to a video display that is not HDCP-compliant.

• Check all audio connections. •

• Check digital audio settings. •

Incorrect digital audio selection

• There is no audio playback on DVD discs during fast or slow modes. •

DVD disc is in fast or slow mode Surround receiver not compatible with 96kHz •

PCM audio DVD Audio disc is loaded without using

• analog audio connection

MPEG-2 decoding

• It is a normal artifact of DVD playback for pictures to jump or show some •

Function not permitted at this time • With most discs, some functions are not permitted at certain times (e.g., •

Requested function not available at this time

• Certain functions may be disabled by the DVD itself during passages of a •

Incorrect match of aspect ratio settingsto disc

• Change aspect ratio settings. •

• Change both batteries. • Sensor is blocked • Clear path to sensor or use optional outboard remote sensor. •

• Many DVDs are encoded with copy protection to prevent copying to VCR. •

• has been forgotten.

proper position.

DVD-R, DVD-RW, DVD+R, DVD+RW (standard conforming), DVD-Audio or DVD-Video; other types will not play.

Progressive Scan/Interlaced Button mode.

Press • Video Off Button b to reactivate video circuitry (see page 43)

The • HDMI Output A may not be used with video displays that are not HDCP-compliant. Unplug the cable and select another audio and video connection (see pages 31 through 32).

Use analog audio outputs. •

Use • 6-Channel Audio Outputs B or Analog Audio Outputs 9.

distortion during rapid play.

Track Skip) or at all (e.g., direct audio track selection).

disc.

Stop play of disc. Press and hold the • Clear Button D until the display blinks. This resets the password and all settings to their defaults.

to toggle to the correct

TROUBLESHOOTING GUIDE

Page 19

Technical Specifications for DVD Player

harman/kardon

DVD 26 and 28/230 Service Manual

Page 19 of 76

Applicable Disc: Disc formats: 5 inch (12 cm) or 3 inch (8 cm) DVD Video, DVD-Audio, Standard conforming DVD+RW, DVD+R, DVD-R, DVD-RW, DivX, VCD, CD, CD-R, MP3, WMA, JPEG or CD-RW discs, Regio code: DVD Movie disc with Code 2 or 0 only. DVD-Layers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Single Layer, Dual Side/Dual Layer Audio formats: DVD-Audio MLP lossless, Linear PCM, MPEG, Windows Media® 9, Dolby Digital or DTS Audio discs Still-image format: JPEG

Video Signal System: PAL/NTSC

HDMI™ Output: Video: 576p, 720p, 1080i

HDMI Version 1.0-compliant HDCP Version 1.1-compliant

Composite Video Output: 1 Vp-p/75 Ohms, sync negative polarity

S Video Output: Y/Luminance: 1 Vp-p/75 Ohms, sync negative polarity

C/Chrominance: 0.286 Vp-p

Component Video Output: Y: 1 Vp-p/75 Ohms, sync negative polarity

Cr: 0.7 Vp-p/75 Ohms

Cb: 0.7 Vp-p/75 Ohms

Analog Audio Output: 2 Vrms max

Frequency Response: DVD (Linear PCM): 2Hz - 22kHz (48kHz sampling)

2Hz - 44kHz (96kHz sampling)

CD: 2Hz - 20kHz

Signal/Noise Ratio (SNR): 105 dB (A-weighted)

Dynamic Range: DVD: 100dB (18 Bit) / 105dB (20 Bit)

CD/DVD: 96dB (16 Bit)

THD/1kHz: DVD/CD: 0.0025 %

Wow & Flutter: Below Measurable Limits

AC Power: 100 - 240 V/50 ~ 60 Hz

Power Consumption: 1 Watt (Standby)/13 Watts (Max)

Dimensions (WxHxD): 440 x 50 x 285 mm

Weight: 4.0 kg

ENGLISH

Depth measurement includes knobs and connectors. Height measurement includes feet and chassis. All specifications subject to change without notice.

Harman Kardon is a registered trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries.

Manufactured under license from Dolby Laboratories. Dolby, Dolby Digital, ProLogic, AC-3 and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents issued & pending. DTS, DTS-ES and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

Windows Media is a registered trademark of Microsoft Corporation in the United States and/or other countries.

Kodak is a registered trademark, and Photo CD is a trademark of Eastman Kodak Company.

Blu-Ray Disc is a trademark of the Blu-Ray Disc Association.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

DivX, DivX Certified, and associated logos are trademarks of DivX Networks, Inc and are used under license.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology m ust be authorized by Macrovision Corporation and is intended for home and other lim ited viewing uses only unless othe rwise authorized by Macrovision Corporation. Reverse engineering or diassembly is prohibited.

CLASS 1

LASER PRODUCT

TECHNICAL SPECIFICATIONS

Page 20

MODEL NAME : DVD 37 & DVD 37/230

ifi

Audi

TDV-540A (ABEX)

harman/kardon

DVD 26 and 28/230 Service Manual

Page 20 of 76

escription : Characteristics Spec

cation o

Test Disc : YEDS7 (SONY), TDV-540A (ABEX) Test Conditions : 10kΩ Load Terminated, AC100V 50/60Hz Test Measuerment : VP-7722A (Audio Analyzer) ,CASCADE SYS-2522(AP)

1.ANALOG AUDIO OUTPUT

Measurement Item

Output Level[Vrms] L

Limit Result

2.0 ± 0.2

YEDS7 (SONY)

Level difference　[Vrms] ＜ 0.2 F/ response [dB] L

Ref.1kHz 0dB L

2 0 H

100　Hz

10　KHz

２０　KHz

４4　KHz

Emphasis L Characteristic[dB] R Ref.1kHz 0dB L

５　KHz

１６　KHz

S/N　[dB] L

Channel Separation　[dB] Ｌ→Ｒ

Ｒ→Ｌ

Linearity　[dB] L

-90dB playback R T.H.D　[%] L

Dynamic Range　[dB] L

-60dB playback R 全高調波歪率　[%] L

ＤＶＤ　９６ｋ R Dynamic Range　[dB] L ＤＶＤ　９６ｋ R

全高調波歪率　[%] L ＤＶＤ　48ｋ R Dynamic Range　[dB] L ＤＶＤ　48ｋ R

０± 1.0

０± 1.5

-4.53±1.0

-9.04 ± 1.0

＞105

> 95

89.5±3

＜ 0.01

＞９3

＜ 0.01

＞９5

＜ 0.01

＞９5

YEDS7 (SONY)

TDV-540A (ABEX) TITLE 4,CHAPTER

AUDIO STREAM 3

YEDS7 (SONY)

TDV-540A (ABEX)

TITLE 3, CHAPTER 1

TDV-540A (ABEX)

TITLE 3, CHAPTER 2

TITLE 2, CHAPTER 1

TITLE 2, CHAPTER 2

TEST DISC

TRACK 1

TRACK 2

TRACK 4

TRACK 10

TRACK 13

TRACK 40

TRACK 41

TRACK 23

TRACK 30

TRACK 22

TRACK 1

TRACK 20

2. DIGITAL OUTPUT

1) OPTICAL OUT JITTER 44.1kHz Normal 44.1kHz

JITTER 96kHz Normal 96kHz

2) COAXIAL OUT OUTPUT Level [mV] Normal CD or DVD Peak to Peak Level at 75ohm L

(mUI) CD Playback

(mUI) DVD Playback

< 50mUI

500±50 (mV)

Playback

Page 21

MODEL NAME : DVD 37& DVD 37/230

harman/kardon

DVD 26 and 28/230 Service Manual

Page 21 of 76

Description : Characteristics Specification of Video Test Disc : TDV-540A (ABEX) , MDVD-111 (TEAC) Serial NO.: Test Conditions : 75Ω Load Terminated AC Input : For USA (120V/60Hz) , For Europe (230V/50Hz) Test Measuerment : VM-700T

4. Video Frequency Respoens (75Ω Terminated)

MP用

Measurement Item Result Test Disc

Composite [dB]

Measurement Item Result Test Disc

S-Video Y [dB]

Measurement Item Result Test Disc

Component Y

[dB]

Interace Mode

Limit

0.5MHz 0dB Ref. 0 1MHz 0dB ± 2dB 2MHz 0dB ± 2dB 3MHz 0dB ± 2dB 4MHz 0dB ± 2dB

5.8MHz -3dB ± 2dB

Limit

0.5MHz 0dB Ref. 0 1MHz 0dB ± 2dB 2MHz 0dB ± 2dB 3MHz 0dB ± 2dB 4MHz 0dB ± 2dB

5.8MHz -3dB ± 2dB

Limit

0.5MHz 0dB Ref. 0 1MHz 0dB ± 2dB 2MHz 0dB ± 2dB 3MHz 0dB ± 2dB 4MHz 0dB ± 2dB

5.8MHz -3dB ± 2dB

MDVD-111

TITLE2,CHAPTER9

100% Multi Brust

MDVD-111

TITLE2,CHAPTER9

100% Multi Brust

MDVD-111

TITLE2,CHAPTER9

100% Multi Brust

Page 22

MODEL NAME : DVD 37& DVD 37/230

harman/kardon

DVD 26 and 28/230 Service Manual

Page 22 of 76

1. Video Level Test (75Ω Terminated)

MP用

Measurement Item Result Test Disc

Limit Composite 1.0V ± 0.1V S-Video Y 1.0V ± 0.1V S-Video C 286mV ± 30mV

Video output [V]

Component Y 1.0V ± 0.1V Component Pb 700mV ± 100mV Component Pr 700mV ± 100mV Scart CVBS 1.0V ± 0.15V

MDVD-111 TITLE2,CHAPTER1 100% COLOR BAR

Scart Red 700mV ± 100mV Scart Green 700mV ± 100mV Scart Blue 700mV ± 100mV

** Pb/Pr & RGB Video Level check before please setting the Black Level off in the set-up menu **

2. Video S/N Raito Test (75Ω Terminated)

Measurement Item Result Test Disc

Limit

Composite ≥ 65.0 dB

Video SNR [dB]

100KHz~4.2MHz

Use SC Trap

S-Video Y ≥ 65.0 dB Component Y ≥ 65.0 dB Component Pb ≥ 65.0 dB

MDVD-111

TITLE2,CHAPTER 4

50% Gray Color

Component Pr ≥ 65.0 dB

3. Chroma Signal AM.PM Test (75Ω Terminated)

Measurement Item Result Test Disc

Chroma AM [dB]

10KHz~500KHz

Chroma PM [dB]

10KHz~500KHz

Composite Chroma ≥ 65.0 dB S-Video Chroma ≥ 65.0 dB

Composite Chroma ≥ 60.0 dB S-Video Chroma ≥ 60.0 dB

Limit

TDV-540A

TITLE2,CHAPTER17

100% Magenta

Color

Page 23

用

2. DVD-Audio Part (Test Disc V-612 , JVC)

harman/kardon

DVD 26 and 28/230 Service Manual

Page 23 of 76

LimitTrack Inform.

Output Level (V)

T.H.D (%) 20KHz LPF

48 / 24

Frequency

Respones (dB)

Ref. : Tr. 38

S/N (dB) "A" Filter

Dynamic Range (dB)

20KHz LPF

96 / 20

192 / 24

Tr.38 1KHz 0dB 2.1±0.2Vrms Tr.38 1KHz 0dB ↓0.01%

Tr.59 17Hz 0±1.0dB Tr.54 10KHz 0±1.0dB Tr.53 20KHz 0±2.0dB

Tr.49 17Hz 0±1.0dB Tr.45 10KHz 0±1.0dB Tr.44 20KHz 0±2.0dB

Tr.22 17Hz 0±1.0dB Tr.18 10KHz 0±1.0dB Tr.17 20KHz 0±2.0dB

Tr.40 Infinity Zero ↑90dB

Tr.39 -60dB ↑85dB

★ SW Level & THD --> Track 38 (30Hz) Play. ★ SW Frequency Respones -> Track 55(31Hz , 0dB) Reference

★ Track 54 (61Hz) , Track 53 (81Hz) , Track 51(127Hz) Play

Downmix 2CH Muiti 5 CH

LT RT FL FR SL SR C

Page 24

1. Instruction manual ass'y - Accessories 2. Package Drawing

harman/kardon

DVD 26 and 28/230 Service Manual

Page 24 of 76

DVD３7/230

POLY BAG

MANUAL INSTRUCTION

HARMAN IMAGE BROCHURES

STAPLE

NO DESCRIPTION PARTS NO.

1 2

SAFETY MANUAL　　　　　　　　　　　　　　　　　　　　　　　　　　　　　ＣＱＸ１Ａ１０４９Ｚ

3 4

INSTRUCTION MANUAL CQX1A1053Z

STAPLE CPL0905 3

1. Cable ass'y - Accessories

POLY BAG

BATTERY ASS'Y

MANUAL SAFETY

CPB1061YPOLY BAG HQE1A273ZHARMAN IMAGE BROCHURES 1

CORD PIN(3P, W/R/Y)

Q,ty

MANUAL ASS'Y

REMOCON ASS'Y

SNOW PAD

1 1

SET

CABLE ASS'Y

BOX ,OUT CARTON

CABLE,S-VHS(1.5M)

CABLE, HDMI(2M)

STAPLE

CORF ,JACK(MONO)1200MM

NO DESCRIPTION PARTS NO. Q,ty

1 2

BATTERY

CORD,PIN(3P,W/R/Y)

CABLE,S-VHS(1.5M)

CORD,JACK(MONO)1200MM CJS9D002Z 1

AC CORD CJA2B020Z 1

CABLE,HDMI(2M) CJS8T001Z 1 STAPLE8 KPL0905

AC CORD

CABR03P CJS4S004Z

CJS0I006Z

1CPB1061YPOLY BAG

MANUAL ASS'Y

2 1

SET DVD３7/230　　　 1 31SNOW,PAD 4

BOX,OUT CARTON

5 6

REMOCON ASS'Y　　　　　　　　　　　　　　　　　　　　　　　　ＣＡＲＴＤＶＤ３７Ａ　　　　　　　　　　　１ 7

CABLE ASS'Y CQXDVD47 1

DESCRIPTIONNO

ＣＱＸＤＶＤ３７Ａ／２３０

CPS1A714 CPS1A715SNOW,PAD

ＣＰＧ１Ａ７９８Ｖ

Q,tyPARTS NO.

Page 25

harman/kardon

DVD 26 and 28/230 Service Manual

Page 25 of 76

Page 26

harman/kardon

DVD 26 and 28/230 Service Manual

Page 26 of 76

Page 27

DVD 26/230 and DVD 28/230 Parts List

harman/kardon

DVD 26 and 28/230 Service Manual

Page 27 of 76

Ref# Component Description REQ-Qty

CHE154 CLAMPER , ARM 0,12 CPS1A830 PAD , SNOW L/R 2 CPS1A831 PAD , SNOW CENTER 1 CQB1A549Y LABEL , ATTENTION DVD48 1 CQB1A622 LABEL , SERIAL NO 3 CQB1A741Z ORIGIN LABEL 1 CQB1A744Z LABEL, DIVX 1 CQB1A907Z LABEL , BAR CODE AVR154 1 CQB5A733T SHEET , TOP LOGO 1 DVD26/230SET SET , DVD PLAYER 1 CGWDVD26/230 FRONT PANEL ASS'Y 1 CBT1A997 KNOB, FUNCTION 1 CGB1A158Y BADGE , FRONT HARMAN/KARDON 1 CGL1A240 INDICATOR, POWER 1 CGR1A387K128 DOOR, DVD 1 CGUDVD26ZA WINDOW ASS'Y 1 CGB1A226Z BADGE , DVD26 1 CGU1A383Z WINDOW, FIP 1 CGW2A413RDH63 PANEL , FRONT DVD48BK 1 CGX1A374YC23 ORNAMENT, DOOR 1 CMZ1A105Y FILTER , FIP 1 CTB3+10JR SCREW 5 CTB3+6JR SCREW 2 CWC4F2A15A120B0CARD , CABLE(15P,1.0mm,120mm,B,8mm) 1 CGX1A375WA AVR350/230 TOP BADGE ASS'Y 1 CGB1A159Y BADGE , TOP HARMAN/KARDON 1 CGX1A375B24 ORNAMENT , BASE AVR350/230 1 CHP1A066 TAPE , BOTH SIDE 1 CHD1A055R SCREW , SPECIAL 1 CKC3A166B35 CABINET , TOP DVD28/230 1 CTBD3+10GFZR SCREW 6 CTBD3+8JFZR SCREW 4 CTB3+6FFZR SCREW 1 CUADVD26/230 BOTTOM CHASSIS ASS'Y 1 CADDVD27ZA DVD MECHANISM ASS'Y(KOMI) 1 CADSDL003YA LOADER ASS'Y 1 CMH1A250 GUIDE, CABLE 1 CWB1B905150EE WIRE ASS'Y 1 CWB5A906150SE WIRE ASS'Y 1 CWC1G2A24G250B CABLE , CARD 1 C4FJ054 TAPE , BOTH SIDE 0,02 CHG1A360 CUSHION , FOOT 4 CHR301 CLAMPER 2 CJA2B043ZA CORD , POWER(EUR) 1 CKF11A303U PANEL , REAR DVD26 1

Page 28

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 28 of 76

CKL2A186H43 FOOT 4 CMX1A176 INSULATOR, SMPS 1 CMX1A180Z INSULATOR 1 COP11840C DVD37 SMPS ASS'Y (DVD37/47) 1 CIP11840C SMPS AUTO ASS'Y 1

CUP11840Z PCB , SMPS 0,5 C905 CCFT1H104ZF CAP , SEMICONDUCTOR 1 C906 CCKT1H391KB CAP , CERAMIC 1 C907 CCEA1HH100T CAP , ELECT 1 C908 CCEA1HH470T CAP , ELECT 1 C910 CCEA1HH1R0T CAP , ELECT 1 C921 CCEA1EH331T CAP , ELECT 1 C922 CCEA1HH0R1T CAP , ELECT 1 C923 CCEA1EH331T CAP , ELECT 1 C924 CCEA1VH101T CAP , ELECT 1 C925 CCEA1EH331T CAP , ELECT 1 C926 HCQI1H102JZT CAP , MYLAR 1 C927 CCEA1HH470T CAP , ELECT 1 C928 CCEA1HH470T CAP , ELECT 1 C929 CCFT1H104ZF CAP , SEMICONDUCTOR 1 C931 CCFT1H104ZF CAP , SEMICONDUCTOR 1 C935 CCFT1H104ZF CAP , SEMICONDUCTOR 1 D906 HVDMTZJ12BT DIODE , ZENER 1 D907 HVD1N4148T DIODE 1 D909 HVDMTZJ24BT DIODE , ZENER 1 D910 HVD1N4148T DIODE 1 D911 HVD1N4148T DIODE 1 D912 HVDMTZJ5.1BT DIODE , ZENER 1 D925 HVD1N4148T DIODE 1 D926 HVDMTZJ12BT DIODE , ZENER 1 D928 HVDMTZJ2.7BT DIODE , ZENER 1 FH91 KJCFC5S HOLDER , FUSE 1 FH92 KJCFC5S HOLDER , FUSE 1 IC92 HVIKIA431BAT I.C , REGULATOR 1 NT91 KRT10D9MSFT THERMISTOR 1 Q904 HVTKTC3198YT T.R 1 Q905 HVTKTA1273YT T.R 1 Q906 HVTKSC1008YT T.R 1 Q907 HVTKRC102MT T.R 1 Q908 HVTKRA102MT T.R 1 Q910 HVTKSC1008YT T.R 1 Q911 HVTKSA708YT T.R 1 Q912 HVDMCR100-6ZL1GSCR (ON SEMI) 1 R901 KROS1TJ105V RES , METAL FILM (1/2W , 1M OHM) 1 R903 CRD25TJ754T RES 1 R904 CRD25TJ754T RES 1 R905 CRD20TJ222T RES , CARBON 1

Page 29

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 29 of 76

R906 CRD20TJ101T RES , CARBON 1 R907 CRD20TJ103T RES , CARBON 1 R909 CRD20TJ100T RES , CARBON 1 R910 CRD20TJ103T RES , CARBON 1 R911 CRD20TJ104T RES , CARBON 1 R912 CRD20TJ102T RES , CARBON 1 R913 CRD20TJ102T RES , CARBON 1 R914 CRD20TJ333T RES , CARBON 1 R920 CRD20TJ101T RES , CARBON 1 R921 CRD20TJ222T RES , CARBON 1 R922 CRD20TF3481T RES , CARBON 1 R923 CRD20TF3001T RES , CARBON 1 R924 CRD20TJ101T RES , CARBON 1 R925 CRD25TJ101T RES , CARBON 1 R926 CRD20TJ101T RES , CARBON 1 R928 CRD20TJ102T RES , CARBON 1 R929 CRD20TJ102T RES , CARBON 1 R930 CRD20TJ101T RES , CARBON 1 R934 CRD20TJ102T RES , CARBON 1 R935 CRD20TJ153T RES , CARBON 1 R940 CRD20TJ472T RES , CARBON 1 CN91 CJP02KA060ZY WAFER 1 CN92 CJP12GA19ZY WAFER 1 C901 HCQF2E104KZE CAP , POLYPROPYLENE FILM 1 C902 HCQF2E104KZE CAP , POLYPROPYLENE FILM 1 C903 CCET400VKRH470KCAP , ELECT(400V/47uF) 1 C904 CCKT3A222KBL CAP , CERAMIC 1 C920 CCEA1EH102T CAP , ELECT 1 C930 CCKDHS222ME CAP , CERAMIC (400V Y-CAP) 1 C932 CCKDHS102ME CAP , CERAMIC (400V Y-CAP) 1 C933 CCKDHS102ME CAP , CERAMIC (400V Y-CAP) 1 D901 HVD1N4007T DIODE 1 D902 HVD1N4007T DIODE 1 D903 HVD1N4007T DIODE 1 D904 HVD1N4007T DIODE 1 D905 HVDUF4007T DIODE , SCHOTTKY 1 D908 HVD1N4007T DIODE 1 D913 HVD1N4148T DIODE 1 D920 HVD31DQ06H DIODE 1 D921 HVDUF4007T DIODE , SCHOTTKY 1 D922 HVD1N4937T DIODE , RECTIFIERS 1 D923 HVD1N4937T DIODE , RECTIFIERS 1 D924 HVDSF26T DIODE , SUPER FAST 1 IC91 BVISG6848DZ IC,PWM 1 LF91 CLZ9Z060Y LINE FILTER 1 L903 CLZ9Z040Y COIL , CHOCK(6.8uH) 1 L905 CLZ9Z040Y COIL , CHOCK(6.8uH) 1

Page 30

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 30 of 76

PC91 HVIPC17L1CB I.C , PHOTO COUPLER 1 Q901 CVIKHB4D5N60F2JAF.E.T HEAT SINK ASS'Y(CMY2A223) 1

CMY2A223 HEAT SINK 1

CTB3+8JR SCREW 1

CVIKHB4D5N60F2 F.E.T(TO-220IS) 1

K8AYG6260 COMPOUND , SILICONE 0,2 Q903 HVTKSB1151Y T.R 1 R902 KRG1SANJ104H RES,METAL OXIDE FILM 1 R908 KRW1PJ1R5V RES , WIRE WOUND(1W, 1.5ohm) 1 R927 KRDS1TJ681V RES , CARBON 1 T901 CLT9Z018ZE TRANS (DVD 27) 1

COP11842F DVD37A/230 PCB ASS'Y 1 CN11 CJP24GA195ZM SMT FFC/FPC WAFER(0.5MM PITCH) 1 C100 CCUS1H104KC CAP , CHIP 1 C101 CCUS1H104KC CAP , CHIP 1 C102 CCUS1H104KC CAP , CHIP 1 C103 CCUS1H104KC CAP , CHIP 1 C104 CCUS1H104KC CAP , CHIP 1 C106 CCUS1H104KC CAP , CHIP 1 C107 CCUS1H104KC CAP , CHIP 1 C110 CCUS1H104KC CAP , CHIP 1 C112 CCUS1H104KC CAP , CHIP 1 C113 CCUS1H104KC CAP , CHIP 1 C115 CCUS1H104KC CAP , CHIP 1 C117 CCUS1H104KC CAP , CHIP 1 C120 CCUS1H104KC CAP , CHIP 1 C122 CCUS1H104KC CAP , CHIP 1 C124 CCUS1H104KC CAP , CHIP 1 C126 CCUS1H104KC CAP , CHIP 1 C127 CCUS1H104KC CAP , CHIP 1 C129 CCUS1H104KC CAP , CHIP 1 C146 CCUS1H104KC CAP , CHIP 1 C156 CCUS1H180JA CAP , CHIP(18PF/50V) 1 C156 CCUS1H180JA CAP , CHIP(18PF/50V) 1 C157 CCUS1H330JA CAP , CHIP 1 C158 CCUS1H330JA CAP , CHIP 1 C159 CCUS1H562KC CAP , CHIP CERAMIC(1608, 5600p) 1 C160 CCUS1H562KC CAP , CHIP CERAMIC(1608, 5600p) 1 C161 CCUS1H562KC CAP , CHIP CERAMIC(1608, 5600p) 1 C163 CCUS1H471JA CAP , CHIP 1 C164 CCUS1H104KC CAP , CHIP 1 C165 CCUS1H104KC CAP , CHIP 1 C166 CCUS1H102KC CAP , CHIP 1 C167 CCUS1H102KC CAP , CHIP 1 C168 CCUS1H102KC CAP , CHIP 1 C169 CCUS1H102KC CAP , CHIP 1 C170 CCUS1H102KC CAP , CHIP 1

Page 31

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 31 of 76

C172 CCUS1H102KC CAP , CHIP 1 C173 CCUS1H102KC CAP , CHIP 1 C174 CCUS1H333KC CAP , CHIP 1 C175 CCUS1H104KC CAP , CHIP 1 C176 CCUS1H102KC CAP , CHIP 1 C178 CCUS1H104KC CAP , CHIP 1 C179 CCUS1H104KC CAP , CHIP 1 C180 CCUS1H104KC CAP , CHIP 1 C181 CCUS1H104KC CAP , CHIP 1 C183 CCUS1H104KC CAP , CHIP 1 C185 CCUS1H104KC CAP , CHIP 1 C186 CCUS1H104KC CAP , CHIP 1 C187 CCUS1H104KC CAP , CHIP 1 C188 CCUS1H104KC CAP , CHIP 1 C189 CCUS1H104KC CAP , CHIP 1 C190 CCUS1H104KC CAP , CHIP 1 C191 CCUS1H104KC CAP , CHIP 1 C192 CCUS1H104KC CAP , CHIP 1 C193 CCUS1H104KC CAP , CHIP 1 C194 CCUS1H104KC CAP , CHIP 1 C195 CCUS1H104KC CAP , CHIP 1 C196 CCUS1H104KC CAP , CHIP 1 C197 CCUS1H104KC CAP , CHIP 1 C199 CCUS1H104KC CAP , CHIP 1 C200 CCUS1H104KC CAP , CHIP 1 C201 CCUS1H104KC CAP , CHIP 1 C204 CCUS1H104KC CAP , CHIP 1 C205 CCUS1H104KC CAP , CHIP 1 C207 CCUS1H272KC CAP , CHIP 1 C208 CCUS1H102KC CAP , CHIP 1 C209 CCUS1H273KC CAP , CHIP 1 C210 CCUS1H102KC CAP , CHIP 1 C214 CCUS1H104KC CAP , CHIP 1 C215 CCUS1H561JA CAP , CHIP 1 C217 CCUS1H273KC CAP , CHIP 1 C218 CCUS1H104KC CAP , CHIP 1 C220 CCUS1H104KC CAP , CHIP 1 C222 CCUS1H104KC CAP , CHIP 1 C225 CCUS1H104KC CAP , CHIP 1 C227 CCUS1H104KC CAP , CHIP 1 C228 CCUS1H222KC CAP , CHIP 1 C229 CCUS1H222KC CAP , CHIP 1 C230 CCUS1H222KC CAP , CHIP 1 C231 CCUS1H222KC CAP , CHIP 1 C232 CCUS1H330JA CAP , CHIP 1 C240 CCUS1H104KC CAP , CHIP 1 C242 CCUS1H104KC CAP , CHIP 1

Page 32

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 32 of 76

C244 CCUS1H104KC CAP , CHIP 1 C245 CCUS1H104KC CAP , CHIP 1 C247 CCUS1H104KC CAP , CHIP 1 C249 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C250 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C252 CCUS1H104KC CAP , CHIP 1 C253 CCUS1H104KC CAP , CHIP 1 C254 CCUS1H272KC CAP , CHIP 1 C255 CCUS1H104KC CAP , CHIP 1 C256 CCUS1H104KC CAP , CHIP 1 C257 CCUS1H104KC CAP , CHIP 1 C260 CCUS1H104KC CAP , CHIP 1 C261 CCUS1H104KC CAP , CHIP 1 C262 CCUS1H104KC CAP , CHIP 1 C263 CCUS1H104KC CAP , CHIP 1 C266 CCUS1H104KC CAP , CHIP 1 C267 CCUS1H104KC CAP , CHIP 1 C276 CCUS1H104KC CAP , CHIP 1 C277 CCUS1H104KC CAP , CHIP 1 C279 CCUS1H104KC CAP , CHIP 1 C280 CCUS1H104KC CAP , CHIP 1 C281 CCUS1H104KC CAP , CHIP 1 C282 CCUS1H104KC CAP , CHIP 1 C283 CCUS1H104KC CAP , CHIP 1 C284 CCUS1H104KC CAP , CHIP 1 C285 CCUS1H104KC CAP , CHIP 1 C286 CCUS1H104KC CAP , CHIP 1 C287 CCUS1H104KC CAP , CHIP 1 C295 CCUS1H104KC CAP , CHIP 1 C304 HCSHB21A220B CAP , TANTAL B2 SIZE 1 C306 HCSHB21A220B CAP , TANTAL B2 SIZE 1 C307 HCSHB21A220B CAP , TANTAL B2 SIZE 1 C308 HCSHB21A220B CAP , TANTAL B2 SIZE 1 C310 CCUS1H102KC CAP , CHIP 1 C311 CCUS1H560JA CAP , CHIP 1 C312 CCUS1H102KC CAP , CHIP 1 C313 CCUS1H102KC CAP , CHIP 1 C336 CCUS1H682KC CAP , CHIP 1 C337 CCUS1H223KC CAP , CHIP 1 C338 CCUS1H221JA CAP , CHIP 1 C339 CCUS1H104KC CAP , CHIP 1 C346 CCUS1H070DA CAP , CHIP 1 C380 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C401 CCUS1H104KC CAP , CHIP 1 C402 CCUS1H104KC CAP , CHIP 1 C403 CCUS1H102KC CAP , CHIP 1 C405 CCUS1H104KC CAP , CHIP 1

Page 33

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 33 of 76

C406 CCUS1H104KC CAP , CHIP 1 C408 CCUS1H104KC CAP , CHIP 1 C429 CCUS1H104KC CAP , CHIP 1 C430 CRJ10DJ0R0T RES , CHIP 1 C431 CCUS1H221JA CAP , CHIP 1 C432 CCUS1H104KC CAP , CHIP 1 C511 CCUS1H151JA CAP , CHIP 1 C531 CCUS1H104KC CAP , CHIP 1 C533 CCUS1H104KC CAP , CHIP 1 C552 CCUS1H104KC CAP , CHIP 1 C553 CCUS1H104KC CAP , CHIP 1 C555 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C556 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C578 CCUS1H104KC CAP , CHIP 1 C580 CCUS1H104KC CAP , CHIP 1 C581 CCUS1H104KC CAP , CHIP 1 C584 CCUS1H104KC CAP , CHIP 1 C585 CCUS1H104KC CAP , CHIP 1 C593 CCUS1H104KC CAP , CHIP 1 C594 CCUS1H104KC CAP , CHIP 1 C615 CCUS1H391JA CAP , CHIP 1 C617 CCUS1H104KC CAP , CHIP 1 C620 CCUS1H104KC CAP , CHIP 1 C630 CCUS1H104KC CAP , CHIP 1 C631 CCUS1H104KC CAP , CHIP 1 C636 CCUS1H391JA CAP , CHIP 1 C638 CCUS1H391JA CAP , CHIP 1 C639 CCUS1H391JA CAP , CHIP 1 C641 CCUS1H391JA CAP , CHIP 1 C644 CCUS1H391JA CAP , CHIP 1 C646 CCUS1H391JA CAP , CHIP 1 C650 CCUS1H391JA CAP , CHIP 1 C657 CCUS1H391JA CAP , CHIP 1 C659 CCUS1H391JA CAP , CHIP 1 C660 CCUS1H391JA CAP , CHIP 1 C662 CCUS1H391JA CAP , CHIP 1 C664 CCUS1H104KC CAP , CHIP 1 C665 CCUS1H104KC CAP , CHIP 1 C668 CCUS1H104KC CAP , CHIP 1 C672 CCUS1H104KC CAP , CHIP 1 C674 CCUS1H104KC CAP , CHIP 1 C677 CCUS1H104KC CAP , CHIP 1 C678 CCUS1H104KC CAP , CHIP 1 C679 CCUS1H104KC CAP , CHIP 1 C809 CCUS1H104KC CAP , CHIP 1 C810 CCUS1H560JA CAP , CHIP 1 C812 CCUS1H101JA CAP , CHIP 1

Page 34

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 34 of 76

C817 CCUS1H104KC CAP , CHIP 1 C819 CCUS1H101JA CAP , CHIP 1 C820 CCUS1H101JA CAP , CHIP 1 C822 CCUS1H560JA CAP , CHIP 1 C823 CCUS1H104KC CAP , CHIP 1 C828 CCUS1H220JA CAP , CHIP 1 C830 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C831 CCUS1H150JA CAP , CHIP(15PF/50V) 1 C834 CCUS1H104KC CAP , CHIP 1 D101 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D102 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D501 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D502 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D511 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D601 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D602 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 D603 HVDRLS4148SR DIODE, SWITCHING, SMD TYPE 1 IC10 HVIZR36778 IC,MPEG (ZORAN) 1 IC11 HVILM1117S-3V3 I.C , REGULATOR (3.3V) 1 IC12 HVILM1117S-1V8 I.C , REGULATOR (1.8V) 1 IC13 HVILM1117S-3V3 I.C , REGULATOR (3.3V) 1 IC14 HVILM1117S-1V8 I.C , REGULATOR (1.8V) 1 IC15 HVIAT24C08N10SC I.C 1 IC17 HVI74VHC04MX I.C , INVERTER 1 IC19 HVIZR36721 IC,HDMI TRANSMITTER(ZORAN) 1 IC20 HVITL3472IDR IC,OP AMP 8-SOIC (TI) 1 IC21 HVIM29W160ET70NIC,16M FLASH (ST) 1 IC22 HVIM12L64164A7T IC, 64M SDRAM (4X16) 1 IC23 HVIAM5888SLF I. C , Motor Driver(AMtek,Pb free) 1 IC24 HVIZR36707 IC,RF (ZORAN) 1 IC40 HVICS4382-KQ I.C , DAC 1 IC41 HVIBH7862FS VIDEO DRIVER(ROHM) 1 IC42 HVIBA7660FS IC , R.G.B DRIVER 1 IC43 HVI74LVC157ADBRI.C , MULTIPLEXER 1 IC45 CVIANAM1441DVD I,C , U-COM DVD37A(ST72F324K2/ST) 1

HVIST72F324K2 IC,FLASH (ST) 1 IC47 HVITC74HCT7007F I.C 1 IC51 HVILM1117S-5.0 IC REGULATOR/SOT-223 1 IC52 HVINJM2068MDTE1I.C , OP AMP 1 IC53 HVILM1117S-3V3 I.C , REGULATOR (3.3V) 1 IC54 HVINJM2068MDTE1I.C , OP AMP 1 IC55 HVINJM2068MDTE1I.C , OP AMP 1 IC56 HVILM1117S-5.0 IC REGULATOR/SOT-223 1 IC57 HVTHN1K05FU MOS FET 1 JK07 HJJ9H003Z JACK , HDMI(JALCO) 1 L101 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L102 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1

Page 35

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 35 of 76

L103 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L104 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L105 HLQ06E100KRZ INDUCTOR , CHIP 1 L106 HLQ06E100KRZ INDUCTOR , CHIP 1 L107 HLQ06E100KRZ INDUCTOR , CHIP 1 L109 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L110 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L111 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L112 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L113 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L114 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L115 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L116 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L117 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L120 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L121 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L123 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L124 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L125 HLZ9R006Z BEAD , CHIP 1 L126 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L127 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L128 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L518 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L519 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L520 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L521 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L522 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L601 BLZ9R004Z BEAD CHIP 90 OHM (2012 SIZE) 1 L602 BLZ9R004Z BEAD CHIP 90 OHM (2012 SIZE) 1 L603 BLZ9R004Z BEAD CHIP 90 OHM (2012 SIZE) 1 L604 BLZ9R004Z BEAD CHIP 90 OHM (2012 SIZE) 1 L610 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L611 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L612 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L613 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L614 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L615 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L617 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L696 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L801 HLQ08ER68KRZ CHIP FERRITE INDUCTOR 1 L802 HLQ08E1R8KRZ CHIP , COIL (1.8UH) 1 L803 HLQ08E1R8KRZ CHIP , COIL (1.8UH) 1 L804 HLQ09E8R2KRZ CHIP , COIL 1 L805 HLQ08ER68KRZ CHIP FERRITE INDUCTOR 1 L806 HLQ08ER39KRZ CHIP FERRITE INDUCTOR 1 L807 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1 L808 HLZ9R001Z FB, 2012(0805)600E, 1.5A,POWER 1

Page 36

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 36 of 76

L809 HLQ09E8R2KRZ CHIP , COIL 1 L884 HLQ08E1R8KRZ CHIP , COIL (1.8UH) 1 Q105 HVTKTA1664YP T.R 1 Q106 HVTKTA1664YP T.R 1 Q108 HVT2N3904SP TR, CHIP (KEC) 1 Q109 HVT2N3904SP TR, CHIP (KEC) 1 Q110 HVT2N3904SP TR, CHIP (KEC) 1 Q307 HVT2SA1955B T.R, TE85L,F, SSM Type, hFE=B 1 Q308 HVT2N3904SP TR, CHIP (KEC) 1 Q315 HVTKRC107S T.R , CHIP 1 Q316 HVTKTA1504SYRTKT.R , CHIP 1 Q404 HVT2N3904SP TR, CHIP (KEC) 1 Q407 HVTKRC107S T.R , CHIP 1 Q408 HVTKRA107ST T.R , CHIP 1 Q501 HVTKTA1504SYRTKT.R , CHIP 1 Q502 HVTKTC3875SYRTKT.R , CHIP 1 Q604 HVTKRA107ST T.R , CHIP 1 Q606 HVTKRA107ST T.R , CHIP 1 Q607 HVTKRA107ST T.R , CHIP 1 Q608 HVTKRC107S T.R , CHIP 1 Q609 HVTKTD1304T T.R , CHIP (MUTE) 1 Q610 HVTKTD1304T T.R , CHIP (MUTE) 1 Q611 HVTKTD1304T T.R , CHIP (MUTE) 1 Q612 HVTKTD1304T T.R , CHIP (MUTE) 1 Q613 HVTKTD1304T T.R , CHIP (MUTE) 1 Q614 HVTKTD1304T T.R , CHIP (MUTE) 1 Q615 HVTKRA107ST T.R , CHIP 1 Q616 HVTKRC107S T.R , CHIP 1 Q617 HVTKTD1304T T.R , CHIP (MUTE) 1 Q618 HVTKTD1304T T.R , CHIP (MUTE) 1 Q619 HVTKTD1304T T.R , CHIP (MUTE) 1 Q620 HVTKTD1304T T.R , CHIP (MUTE) 1 Q621 HVTKTD1304T T.R , CHIP (MUTE) 1 Q622 HVTKTD1304T T.R , CHIP (MUTE) 1 Q801 HVTKRC107S T.R , CHIP 1 Q802 HVTKRC107S T.R , CHIP 1 Q803 HVTKTA1504SYRTKT.R , CHIP 1 Q804 HVTKTA1504SYRTKT.R , CHIP 1 Q805 HVTKTD1304T T.R , CHIP (MUTE) 1 Q806 HVTKRA107ST T.R , CHIP 1 Q821 HVTKTA1504SYRTKT.R , CHIP 1 R100 CRJ10DJ472T RES , CHIP 1 R101 CRJ10DF4700T RES, CHIP 470 OHM/1608/1% 1 R102 CRJ10DJ0R0T RES , CHIP 1 R103 CRJ10DF4300T RES 1 R104 CRJ10DF3920T RES. CHIP (392R 1%) 1 R105 CRJ10DJ0R0T RES , CHIP 1

Page 37

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 37 of 76

R109 CRJ10DJ472T RES , CHIP 1 R112 CRJ10DJ202T RES , CHIP 1 R113 CRJ10DJ202T RES , CHIP 1 R114 CRJ10DJ121T RES , CHIP 1 R115 CRJ10DJ0R0T RES , CHIP 1 R116 CRJ10DJ121T RES , CHIP 1 R117 CRJ10DJ121T RES , CHIP 1 R118 CRJ10DJ103T RES , CHIP 1 R123 CRJ10DJ0R0T RES , CHIP 1 R124 CRJ10DJ0R0T RES , CHIP 1 R125 CRJ10DJ113T RES , CHIP 1 R126 CRJ10DJ0R0T RES , CHIP 1 R127 CRJ10DJ0R0T RES , CHIP 1 R128 CRJ10DJ121T RES , CHIP 1 R133 CRJ10DF3920T RES. CHIP (392R 1%) 1 R134 CRJ10DJ0R0T RES , CHIP 1 R135 CRJ10DJ100T RES , CHIP 1 R136 CRJ10DJ221T RES , CHIP 1 R137 CRJ10DJ221T RES , CHIP 1 R138 CRJ10DJ100T RES , CHIP 1 R139 CRJ10DJ472T RES , CHIP 1 R140 CRJ10DJ133T RES , CHIP 1 R141 CRJ10DJ474T RES , CHIP 1 R142 CRJ10DJ474T RES , CHIP 1 R144 CRJ10DJ330T RES , CHIP 1 R145 CRJ10DJ750T RES , CHIP 1 R146 CRJ10DJ0R0T RES , CHIP 1 R147 CRJ10DJ104T RES , CHIP 1 R148 CRJ10DJ750T RES , CHIP 1 R149 CRJ104DJ470T RES , 4ARRAY (1608*4) 1 R150 CRJ104DJ470T RES , 4ARRAY (1608*4) 1 R151 CRJ10DJ0R0T RES , CHIP 1 R152 CRJ10DJ0R0T RES , CHIP 1 R153 CRJ10DJ0R0T RES , CHIP 1 R154 CRJ10DJ0R0T RES , CHIP 1 R155 CRJ10DJ101T RES , CHIP 1 R157 CRJ10DJ0R0T RES , CHIP 1 R158 CRJ104DJ101T RES , CHIP NETWORK(1/16W, 100ohm, 1608 R159 CRJ10DJ472T RES , CHIP 1 R160 CRJ10DJ330T RES , CHIP 1 R162 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R163 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R164 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R165 CRJ10DJ330T RES , CHIP 1 R166 CRJ10DJ330T RES , CHIP 1 R167 CRJ10DJ330T RES , CHIP 1 R168 CRJ104DJ330T RES , 4ARRAY (1608*4) 1

Page 38

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 38 of 76

R169 CRJ10DJ750T RES , CHIP 1 R170 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R171 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R172 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R173 CRJ104DJ330T RES , 4ARRAY (1608*4) 1 R174 CRJ10DJ472T RES , CHIP 1 R175 CRJ10DJ912T RES , CHIP 1 R176 CRJ10DJ132T RES , CHIP 1 R177 CRJ10DJ132T RES , CHIP 1 R178 CRJ10DJ272T RES , CHIP 1 R180 CRJ10DJ0R0T RES , CHIP 1 R181 CRJ10DJ0R0T RES , CHIP 1 R182 CRJ10DJ0R0T RES , CHIP 1 R183 CRJ10DF1202T RES , CHIP 1% 1 R184 CRJ10DJ471T RES , CHIP 1 R185 CRJ10DJ332T RES , CHIP 1 R186 CRJ10DJ332T RES , CHIP 1 R187 CRJ10DJ332T RES , CHIP 1 R188 CRJ10DJ113T RES , CHIP 1 R189 CRJ10DJ105T RES , CHIP 1 R190 CRJ10DJ223T RES , CHIP 1 R191 CRJ10DJ223T RES , CHIP 1 R192 CRJ10DJ103T RES , CHIP 1 R193 CRJ10DJ332T RES , CHIP 1 R194 CRJ10DJ750T RES , CHIP 1 R195 CRJ10DJ101T RES , CHIP 1 R196 CRJ10DJ472T RES , CHIP 1 R199 CRJ10DJ330T RES , CHIP 1 R200 CRJ10DJ330T RES , CHIP 1 R201 CRJ10DJ472T RES , CHIP 1 R202 CRJ10DJ622T RES , CHIP 1 R203 CRJ10DJ562T RES , CHIP 1 R204 CRJ10DJ562T RES , CHIP 1 R205 CRJ10DJ562T RES , CHIP 1 R206 CRJ10DJ103T RES , CHIP 1 R207 CRJ10DF4700T RES, CHIP 470 OHM/1608/1% 1 R209 CRJ10DF1002T RES , CHIP 1% 1 R210 CRJ10DF1002T RES , CHIP 1% 1 R211 CRJ10DF1002T RES , CHIP 1% 1 R219 CRJ10DJ273T RES , CHIP 1 R220 CRJ10DJ562T RES , CHIP 1 R221 CRJ10DJ562T RES , CHIP 1 R222 CRJ10DJ562T RES , CHIP 1 R230 CRJ10DJ472T RES , CHIP 1 R241 CRJ10DF75R0T RES, CHIP 1% 75 OHM 1 R243 CRJ10DF75R0T RES, CHIP 1% 75 OHM 1 R244 CRJ10DF75R0T RES, CHIP 1% 75 OHM 1

Page 39

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 39 of 76

R265 CRJ10DJ472T RES , CHIP 1 R284 CRJ10DJ472T RES , CHIP 1 R285 CRJ10DJ472T RES , CHIP 1 R287 CRJ10DJ113T RES , CHIP 1 R297 CRJ10DJ0R0T RES , CHIP 1 R298 CRJ10DJ103T RES , CHIP 1 R299 CRJ10DJ0R0T RES , CHIP 1 R301 CRJ10DJ0R0T RES , CHIP 1 R302 CRJ10DJ0R0T RES , CHIP 1 R303 CRJ10DJ0R0T RES , CHIP 1 R305 CRJ10DJ472T RES , CHIP 1 R306 CRJ10DJ0R0T RES , CHIP 1 R307 CRJ10DJ272T RES , CHIP 1 R308 CRJ10DJ102T RES , CHIP 1 R309 CRJ10DJ102T RES , CHIP 1 R377 CRJ10DJ221T RES , CHIP 1 R404 CRJ10DJ333T RES , CHIP 1 R409 CRJ10DJ100T RES , CHIP 1 R410 CRJ10DJ103T RES , CHIP 1 R412 CRJ10DJ681T RES , CHIP 1 R413 CRJ10DJ821T RES , CHIP 1 R414 CRJ10DJ122T RES , CHIP 1 R415 CRJ10DJ152T RES , CHIP 1 R416 CRJ10DJ222T RES , CHIP 1 R417 CRJ10DJ332T RES , CHIP 1 R418 CRJ10DJ472T RES , CHIP 1 R419 CRJ10DJ561T RES , CHIP 1 R420 CRJ10DJ750T RES , CHIP 1 R421 CRJ10DJ680T RES , CHIP 1 R422 CRJ10DJ121T RES , CHIP 1 R423 CRJ10DJ820T RES , CHIP 1 R424 CRJ10DJ4R7T RES , CHIP 1 R425 CRJ10DJ472T RES , CHIP 1 R501 CRJ10DJ182T RES , CHIP 1 R502 CRJ10DJ182T RES , CHIP 1 R503 CRJ10DJ103T RES , CHIP 1 R504 CRJ10DJ473T RES , CHIP 1 R505 CRJ10DJ470T RES , CHIP 1 R506 CRJ10DJ271T RES , CHIP 1 R511 CRJ10DJ0R0T RES , CHIP 1 R512 CRJ10DJ0R0T RES , CHIP 1 R513 CRJ10DJ103T RES , CHIP 1 R514 CRJ10DJ100T RES , CHIP 1 R515 CRJ10DJ103T RES , CHIP 1 R516 CRJ10DJ103T RES , CHIP 1 R517 CRJ10DJ103T RES , CHIP 1

R518 CRJ10DJ103T RES , CHIP 1

Page 40

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 40 of 76

R519 CRJ10DJ473T RES , CHIP 1 R522 CRJ10DJ0R0T RES , CHIP 1 R533 CRJ10DJ0R0T RES , CHIP 1 R544 CRJ10DJ0R0T RES , CHIP 1 R549 CRJ10DJ105T RES , CHIP 1 R552 CRJ10DJ0R0T RES , CHIP 1 R553 CRJ10DJ0R0T RES , CHIP 1 R564 CRJ10DJ472T RES , CHIP 1 R593 CRJ10DJ750T RES , CHIP 1 R600 CRJ10DJ132T RES , CHIP 1 R601 CRJ10DJ132T RES , CHIP 1 R602 CRJ10DJ132T RES , CHIP 1 R603 CRJ10DJ132T RES , CHIP 1 R604 CRJ10DJ132T RES , CHIP 1 R605 CRJ10DJ132T RES , CHIP 1 R606 CRJ10DJ132T RES , CHIP 1 R607 CRJ10DJ132T RES , CHIP 1 R608 CRJ10DJ132T RES , CHIP 1 R609 CRJ10DJ132T RES , CHIP 1 R611 CRJ10DJ0R0T RES , CHIP 1 R612 CRJ10DJ332T RES , CHIP 1 R618 CRJ10DJ332T RES , CHIP 1 R619 CRJ10DJ101T RES , CHIP 1 R620 CRJ10DJ132T RES , CHIP 1 R621 CRJ10DJ132T RES , CHIP 1 R622 CRJ10DJ132T RES , CHIP 1 R623 CRJ10DJ132T RES , CHIP 1 R624 CRJ10DJ102T RES , CHIP 1 R625 CRJ10DJ332T RES , CHIP 1 R626 CRJ10DJ332T RES , CHIP 1 R627 CRJ10DJ332T RES , CHIP 1 R628 CRJ10DJ102T RES , CHIP 1 R629 CRJ10DJ332T RES , CHIP 1 R630 CRJ10DJ221T RES , CHIP 1 R631 CRJ10DJ221T RES , CHIP 1 R632 CRJ10DJ104T RES , CHIP 1 R633 CRJ10DJ104T RES , CHIP 1 R641 CRJ10DJ224T RES , CHIP 1 R642 CRJ10DJ224T RES , CHIP 1 R650 CRJ10DJ132T RES , CHIP 1 R651 CRJ10DJ132T RES , CHIP 1 R652 CRJ10DJ132T RES , CHIP 1 R653 CRJ10DJ132T RES , CHIP 1 R654 CRJ10DJ102T RES , CHIP 1 R655 CRJ10DJ332T RES , CHIP 1 R656 CRJ10DJ332T RES , CHIP 1

R657 CRJ10DJ332T RES , CHIP 1

Page 41

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 41 of 76

R658 CRJ10DJ102T RES , CHIP 1 R659 CRJ10DJ332T RES , CHIP 1 R660 CRJ10DJ102T RES , CHIP 1 R661 CRJ10DJ102T RES , CHIP 1 R662 CRJ10DJ104T RES , CHIP 1 R663 CRJ10DJ104T RES , CHIP 1 R664 CRJ10DJ102T RES , CHIP 1 R665 CRJ10DJ102T RES , CHIP 1 R666 CRJ10DJ102T RES , CHIP 1 R667 CRJ10DJ102T RES , CHIP 1 R668 CRJ10DJ104T RES , CHIP 1 R669 CRJ10DJ104T RES , CHIP 1 R670 CRJ10DJ102T RES , CHIP 1 R671 CRJ10DJ102T RES , CHIP 1 R672 CRJ10DJ332T RES , CHIP 1 R673 CRJ10DJ102T RES , CHIP 1 R674 CRJ10DJ332T RES , CHIP 1 R675 CRJ10DJ102T RES , CHIP 1 R676 CRJ10DJ102T RES , CHIP 1 R677 CRJ10DJ102T RES , CHIP 1 R678 CRJ10DJ132T RES , CHIP 1 R679 CRJ10DJ132T RES , CHIP 1 R680 CRJ10DJ132T RES , CHIP 1 R681 CRJ10DJ132T RES , CHIP 1 R685 CRJ10DJ101T RES , CHIP 1 R686 CRJ10DJ0R0T RES , CHIP 1 R687 CRJ10DJ0R0T RES , CHIP 1 R688 CRJ10DJ0R0T RES , CHIP 1 R694 CRJ10DJ0R0T RES , CHIP 1 R695 CRJ10DJ0R0T RES , CHIP 1 R698 CRJ10DJ132T RES , CHIP 1 R699 CRJ10DJ132T RES , CHIP 1 R726 CRJ10DJ474T RES , CHIP 1 R727 CRJ10DJ221T RES , CHIP 1 R728 CRJ10DJ223T RES , CHIP 1 R729 CRJ10DJ221T RES , CHIP 1 R730 CRJ10DJ221T RES , CHIP 1 R731 CRJ10DJ221T RES , CHIP 1 R732 CRJ10DJ221T RES , CHIP 1 R733 CRJ10DJ222T RES , CHIP 1 R734 CRJ10DJ222T RES , CHIP 1 R735 CRJ10DJ222T RES , CHIP 1 R736 CRJ10DJ222T RES , CHIP 1 R737 CRJ10DJ222T RES , CHIP 1 R738 CRJ10DJ222T RES , CHIP 1 R739 CRJ10DJ224T RES , CHIP 1

R744 CRJ10DJ222T RES , CHIP 1

Page 42

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 42 of 76

R745 CRJ10DJ222T RES , CHIP 1 R746 CRJ10DJ222T RES , CHIP 1 R747 CRJ10DJ222T RES , CHIP 1 R748 CRJ10DJ222T RES , CHIP 1 R749 CRJ10DJ222T RES , CHIP 1 R801 CRJ10DJ0R0T RES , CHIP 1 R802 CRJ10DJ820T RES , CHIP 1 R803 CRJ10DJ0R0T RES , CHIP 1 R806 CRJ10DJ820T RES , CHIP 1 R807 CRJ10DJ680T RES , CHIP 1 R808 CRJ10DJ680T RES , CHIP 1 R809 CRJ10DJ680T RES , CHIP 1 R810 CRJ10DJ471T RES , CHIP 1 R811 CRJ10DJ471T RES , CHIP 1 R812 CRJ10DJ102T RES , CHIP 1 R813 CRJ10DJ821T RES , CHIP 1 R814 CRJ10DJ750T RES , CHIP 1 R815 CRJ10DJ181T RES , CHIP 1 R816 CRJ10DJ390T RES , CHIP 1 R817 CRJ10DJ750T RES , CHIP 1 R818 CRJ10DJ750T RES , CHIP 1 R821 CRJ10DJ0R0T RES , CHIP 1 R823 CRJ10DJ0R0T RES , CHIP 1 R824 CRJ10DJ750T RES , CHIP 1 R825 CRJ10DJ101T RES , CHIP 1 R826 CRJ10DJ222T RES , CHIP 1 R827 CRJ10DJ221T RES , CHIP 1 R828 CRJ18AJ221T RES , CHIP 1 R829 CRJ10DJ104T RES , CHIP 1 R830 CRJ10DJ390T RES , CHIP 1 R831 CRJ10DJ620T RES , CHIP 1 R832 CRJ10DJ102T RES , CHIP 1 R833 CRJ10DJ750T RES , CHIP 1 R834 CRJ10DJ820T RES , CHIP 1 R878 CRJ10DJ104T RES , CHIP 1 R879 CRJ10DJ101T RES , CHIP 1 R880 CRJ10DJ221T RES , CHIP 1 R895 CRJ10DJ221T RES , CHIP 1 R896 CRJ10DJ680T RES , CHIP 1 X101 HOX27000E180S CRYSTAL , CHIP(27MHZ,SMD) 1 C105 CCEA1CH470T CAP , ELECT 1 C108 CCEA1CH101T CAP , ELECT 1 C109 CCEA1CH101T CAP , ELECT 1 C111 CCEA1CH101T CAP , ELECT 1 C114 CCEA1CH101T CAP , ELECT 1 C116 CCEA1CH101T CAP , ELECT 1 C118 CCEA1CH101T CAP , ELECT 1

Page 43

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 43 of 76

C119 CCEA1CH101T CAP , ELECT 1 C121 CCEA1CH101T CAP , ELECT 1 C123 CCEA1CH101T CAP , ELECT 1 C125 CCEA1CH101T CAP , ELECT 1 C128 CCEA1CH101T CAP , ELECT 1 C130 CCEA1CH101T CAP , ELECT 1 C137 CCEA1CH470T CAP , ELECT 1 C155 CCEA1CH470T CAP , ELECT 1 C177 CCEA1CH101T CAP , ELECT 1 C182 CCEA1CH470T CAP , ELECT 1 C184 CCEA1CH470T CAP , ELECT 1 C198 CCEA1CH101T CAP , ELECT 1 C202 CCEA1CH470T CAP , ELECT 1 C203 CCEA1CH470T CAP , ELECT 1 C206 CCEA1CH470T CAP , ELECT 1 C213 CCEA1CH221T CAP , ELECT 1 C219 CCEA1CH470T CAP , ELECT 1 C221 CCEA1CH101T CAP , ELECT 1 C223 CCEA1CH101T CAP , ELECT 1 C224 CCEA1CH101T CAP , ELECT 1 C226 CCEA1CH101T CAP , ELECT 1 C233 CCEA1CH101T CAP , ELECT 1 C241 CCEA1CH470T CAP , ELECT 1 C243 CCEA1CH470T CAP , ELECT 1 C251 CCEA1CH470T CAP , ELECT 1 C258 CCEA1HH4R7T CAP , ELECT 1 C301 CCEA1CH101T CAP , ELECT 1 C404 CCEA1CKS470T CAP , ELECT 1 C504 CCEA1CH221T CAP , ELECT 1 C508 CCEA1CH221T CAP , ELECT 1 C510 CCEA1HH4R7T CAP , ELECT 1 C530 CCEA1CH221T CAP , ELECT 1 C532 CCEA1CH221T CAP , ELECT 1 C548 CCEA1CH221T CAP , ELECT 1 C549 CCEA1CH221T CAP , ELECT 1 C561 CCEA1CH100T CAP , ELECT 1 C562 CCEA1HH1R0T CAP , ELECT 1 C574 CCEA1CH221T CAP , ELECT 1 C579 CCEA1CH221T CAP , ELECT 1 C582 CCEA1CH470T CAP , ELECT 1 C583 CCEA1CH221T CAP , ELECT 1 C586 CCEA1CH221T CAP , ELECT 1 C616 CCEA1CH220T CAP , ELECT 1 C618 CCEA1CH101T CAP , ELECT 1 C628 CCEA1CH101T CAP , ELECT 1 C629 CCEA1CH101T CAP , ELECT 1 C637 HCQI1H222JZT CAP , MYLAR 1

Page 44

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 44 of 76

C640 HCQI1H222JZT CAP , MYLAR 1 C642 CCEA1CH220T CAP , ELECT 1 C643 CCEA1CH220T CAP , ELECT 1 C645 HCQI1H222JZT CAP , MYLAR 1 C648 HCQI1H222JZT CAP , MYLAR 1 C653 CCEA1CH220T CAP , ELECT 1 C658 HCQI1H222JZT CAP , MYLAR 1 C661 HCQI1H222JZT CAP , MYLAR 1 C666 CCEA1CH101T CAP , ELECT 1 C667 CCEA1CH101T CAP , ELECT 1 C669 CCEA1CH101T CAP , ELECT 1 C673 CCEA1CH101T CAP , ELECT 1 C675 CCEA1CH470T CAP , ELECT 1 C676 CCEA1HH1R0T CAP , ELECT 1 C680 CCEA1CH221T CAP , ELECT 1 C681 CCEA1CH101T CAP , ELECT 1 C685 HCQI1H222JZT CAP , MYLAR 1 C687 HCQI1H222JZT CAP , MYLAR 1 C688 HCQI1H222JZT CAP , MYLAR 1 C689 HCQI1H222JZT CAP , MYLAR 1 C690 HCQI1H222JZT CAP , MYLAR 1 C692 HCQI1H222JZT CAP , MYLAR 1 C733 CCEA1HH3R3T CAP , ELECT 1 C751 CCEA1CH220T CAP , ELECT 1 C752 CCEA1CH220T CAP , ELECT 1 C795 CCEA1CH221T CAP , ELECT 1 C801 CCEA1AH331T CAP , ELECT 1 C802 CCEA1AH331T CAP , ELECT 1 C803 CCEA1CH220T CAP , ELECT 1 C804 CCEA1CH101T CAP , ELECT 1 C811 CCEA1AH331T CAP , ELECT 1 C813 CCEA1AH331T CAP , ELECT 1 C815 CCEA1AH331T CAP , ELECT 1 C818 CCEA1AH331T CAP , ELECT 1 C824 CCEA1HH1R0T CAP , ELECT 1 C825 CCEA1HH1R0T CAP , ELECT 1 C826 CCEA1CH470T CAP , ELECT 1 C827 CCEA1CH470T CAP , ELECT 1 C829 CCEA1AH471T CAP , ELECT 1 C835 CCEA1CH221T CAP , ELECT 1 C882 CCEA1AH471T CAP , ELECT 1 C891 CCEA1AH471T CAP , ELECT 1 IC50 HVIKA79L08AZT REGULATOR, -8V 1 Q605 HVTKSA916YT T.R 1 S401 CST1A024ZT SW , TACT 1 S402 CST1A024ZT SW , TACT 1 S403 CST1A024ZT SW , TACT 1

Page 45

Ref# Component Description REQ-Qt

harman/kardon

DVD 26 and 28/230 Service Manual

Page 45 of 76

S404 CST1A024ZT SW , TACT 1 S405 CST1A024ZT SW , TACT 1 S406 CST1A024ZT SW , TACT 1 S407 CST1A024ZT SW , TACT 1 S408 CST1A024ZT SW , TACT 1

CMD1A504 BRACKET , FIP 2

CQB1D022 A-ROHS/LABEL,SERIAL 1 BN01 CWB1C912060EN WIRE ASS'Y 1 BN07 CWB1A906190EN WIRE ASS'Y 1 CN01 CJP15GA117ZY WAFER , CARD CABLE 1 CN03 CJP07GA01ZY WAFER , STRAIGHT(7PIN) 1 CN05 CJP15GB113ZY WAFER 1 CN07 CJP06GA19ZY WAFER , STRAIGHT(DVD LOADER) 1 CN12 CJP05GA19ZY WAFER , STRAIGHT 1 CN13 CJP06GA19ZY WAFER , STRAIGHT(DVD LOADER) 1 D103 CVD1N4003ST DIODE , RECT 1 D104 CVD1N4003ST DIODE , RECT 1 D105 CVD1N4003ST DIODE , RECT 1 D107 CVD1N4003ST DIODE , RECT 1 D109 CVD1N4003ST DIODE , RECT 1 D110 CVD1N4003ST DIODE , RECT 1 D401 CVD50BOBBWGA L.E.D , 2 COLOR (ORG , BLUE) 1 ET01 CMC1A111 PLATE , EARTH 1 ET02 CMC1A111 PLATE , EARTH 1 F401 CFL13BT229GINAK F.I.P (FUTABA , 13BT229GINAK) 1 IC46 BVIKP1010B IC, PHOTO COUPLER 1 IC49 HVIKIA7808API I.C , REGULATOR +8V 1 IC61 HRVKSM603TH2 SENSOR , REMOCON 1 JK01 CJJ4R041Z 6P JACK, BOARD 1 JK02 CJJ4N067Z JACK , 2P 1 JK03 CJJ4S043Z JACK , BOARD 1 JK04 CJJ9N003Z JACK , S-VIDEO+VHS 1 JK05 CJJ6K003Z JACK, SCART 1 JK06 CJS9U011Z JACK, OPTICAL+COXIAL(GOLD PLATE) 1 JK08 HJJ1D002Z JACK , STEREO(2P 3.5PIE) 1 X501 HOX08000E160C CRYSTAL 8MHz 1

CQB1A778Z LABEL , DTS 1

CTB3+10JR SCREW 2

CTB3+8JR SCREW 3

CTW3+8JR SCREW 7

CUA2A259 CHASSIS , BOTTOM 1

KBA2C2000TLEY FUSE 1

KHG1A326Z LUG CUSHION 2

KHR1A028 BUSHING , AC CORD 1

KMC1A264 CUSHION , SHIELD 1

Page 46

harman/kardon

DVD 26 and 28/230 Service Manual

Page 46 of 76

Page 47

harman/kardon

DVD 26 and 28/230 Service Manual

Page 47 of 76

Page 48

harman/kardon

DVD 26 and 28/230 Service Manual

Page 48 of 76

Page 49

harman/kardon

DVD 26 and 28/230 Service Manual

Page 49 of 76

Page 50

harman/kardon

DVD 26 and 28/230 Service Manual

Page 50 of 76

Page 51

ESMT M12L64164A

harman/kardon

DVD 26 and 28/230 Service Manual

Page 51 of 76

SDRAM

1M x 16 Bit x 4 Banks

Synchronous DRAM

FEATURES

 JEDEC standard 3.3V power supply  LVTTL compatible with multiplexed address  Four banks operation  MRS cycle with address key programs

- CAS Latency (2 & 3)

- Burst Length (1, 2, 4, 8 & full page)

- Burst Type (Sequential & Interleave)

 All inputs are sampled at the positive going edge of the

system clock

 DQM for masking  Auto & self refresh  64ms refresh period (4K cycle)

GENERAL DESCRIPTION

The M12L64164A is 67,108,864 bits synchronous high data rate Dynamic RAM organized as 4 x 1,048, 576 words by 16 bits. S ynchronous desig n allo ws precis e c ycle co ntrols with the use of sy stem clock I/O transactions are poss ible o n every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications.

PIN ASSIGNMENT

ORDERING INFORMATION

54 Pin TSOP (Type II) (400mi l x 875mil )

PRODUCT NO. MAX FREQ. PACKAGE

M12L64164A-6T 166MHz

M12L64164A-7T 143MHz

TSOP II

DQ0

DDQ

DQ1 DQ2

SSQ

DQ3 DQ4

DDQ

DQ5 DQ6

SSQ

DQ7

LDQM

WE CAS RAS

CS A A12

A10/AP

A A1 A2 A3

VDD

Top View

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28

DQ15 V

SSQ

DQ14 DQ13 V

DDQ

DQ12 DQ11 V

SSQ

DQ10 DQ9 V

DDQ

DQ8 V

NC UDQM CLK CKE NC A

A9 A8 A7 A6 A5 A4 VSS

Elite Semiconductor Memory Technology Inc. Publication Date: Mar. 2003

Revision: 1.7 1/44

Page 52

harman/kardon

DVD 26 and 28/230 Service Manual

Page 52 of 76

Page 53

74VHC04

harman/kardon

DVD 26 and 28/230 Service Manual

Page 53 of 76

Hex Inverte r

74VHC04 Hex Inverter

November 1992

Revised February 2005

General Description

The V HC04 i s an adv anced hi gh speed C MOS Inv erter fabricated with silicon gate CMOS technology. It achieves the hi gh sp eed op eration si milar to e quivalent B ipolar Schottky TTL while maintaining the CMOS low power dissipation.

The internal circuit is composed of 3 stages including buffer output, which provide high no ise immunity and stable output. An input protection circuit ensures that 0V to 7V can be applied to the input pins without re gard to the supply voltage. This device can be used to interface 5V to 3V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages.

Features

■ High Speed: t

■ High noise immunity: V

■ Power down protection is provided on all inputs

■ Low Noise: V

■ Low power dissipation: I

■ Pin and function compatible with 74HC04

3.8 ns (typ) at VCC 5V

28% VCC (Min)

NIL

2 PA (Max) @ TA 25qC

0.4V (typ)

OLP

NIH

Ordering Code:

Order Number

74VHC04M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow

74VHC04MX_NL (Note 1)

74VHC04SJ M14D Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide

74VHC04MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide

74VHC04MTCX_NL (Note 1)

74VHC04N N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide

Surface mount packag es are also available on Tape and Reel. Specify by ap pending the suffix letter “X ” to the ordering code. Pb-Free package per JEDEC J-STD-020B.

Note 1: “_NL” indicates Pb-Free pac kage (per JEDEC J-S TD-020B). Device availa ble in Tape and Reel only.

Package

Number

M14A Pb-Free 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow

MTC14 Pb-Free 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm

Wide

Package Description

Logic Symbol

74VHC04

Pin Descriptions

Pin Names Description

IEEE/IEC

Inputs

Outputs

Connection Diagram

Truth Table

Page 54

Features

harman/kardon

DVD 26 and 28/230 Service Manual

Page 54 of 76

• Medium-voltage and Standard-voltage Operation

– 5.0 (VCC = 4.5V to 5.5V) – 2.7 (V

• Automotive Temperature Range –40°C to 125°C

• Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K),

1024 x 8 (8K) or 2048 x 8 (16K)

• Two-wire Serial Interface

• Schmitt Trigger, Filtered Inputs for Noise Suppression

• Bidirectional Data Transfer Protocol

• 400 kHz (2.7V) Compatibility

• Write Protect Pin for Hardware Data Protection

• 8-byte Page (1K, 2K), 16-byte Page (4K, 8K, 16K) Write Modes

• Partial Page Writes are Allowed

• Self-timed Write Cycle (5 ms max)

• High-reliability

– Endurance: 1 Million Write Cycles – Data Retention: 100 Years

• 8-lead PDIP, 8-lead JEDEC SOIC, and 8-lead TSSOP Packages

= 2.7V to 5.5V)

Two-wire Automotive Temperature Serial EEPROM

1K (128 x 8)

Description

The AT24C01A/02/04/08A/16A provides 1024/2048/4096/8192/16384 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 128/256/512/1024/2048 words of 8 bits each. The device is optimized for use in many automotive applications where low-power and low-voltage operation are essential. The AT24C01A/02/04/08A/16A is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, and 8-lead TSSOP packages and is accessed via a two-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) versions.

8-lead PDIP

Table 1. Pin Configurations

Pin Name Function

A0 − A2 Address Inputs

SDA Serial Data

SCL Serial Clock Input

WP Write Protect

NC No Connect

GND

A0 A1 A2

GND

8-lead SOIC

1 2 3 4

VCC

SCL

SDA

VCC

SCL

SDA

2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) 16K (2048 x 8)

AT24C01A AT24C02 AT24C04 AT24C08A AT24C16A

A0 A1 A2

GND

8-lead TSSOP

1 2 3 4

8 7 6 5

VCC WP SCL SDA

5092B–SEEPR–9/05

Page 55

SEMICONDUCTOR

TECHNICAL DATA

THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, 24V.

FEATURES

Suitable for C-MOS, TTL, the Other Digital IC's Power Supply. Internal Thermal Overload Protection. Internal Short Circuit Current Limiting. Output Current in Excess of 1A. Satisfies IEC-65 Specification. (International Electronical Commission)

MAXIMUM RATINGS (Ta=25 )

KIA7805API~ KIA7824API

BIPOLAR LINEAR INTEGRATED CIRCUIT

CHARACTERISTIC SYMBOL RATING UNIT

Input Voltage

KIA7805API KIA7815API

KIA7818API KIA7824API

Power Dissipation (Tc=25 )

20.8 W

Power Dissipation (Without Heatsink)

KIA7805API KIA7824API

2.0 W

Operating Junction Temperature

-30 150

Storage Temperature

stg

-55 150

harman/kardon

DVD 26 and 28/230 Service Manual

Page 55 of 76

TO-220IS

1. INPUT

2. COMMON

3. OUTPUT

DIM MILLIMETERS

A B C D E F G 12.30 MAX

J K L

N O P Q R

S T U

10.30 MAX

15.30 MAX

2.70Ź0.30

0.85 MAX

Φ3.20Ź0.20

3.00Ź0.30

0.75 MAXH

13.60Ź0.50

3.90 MAX

1.20

1.30

2.54

4.50Ź0.20

6.80

2.60Ź0.20 10Ɓ 25Ş

5Ş

0.5

2.60Ź0.15V

Page 56

THREE TERMINAL POSITIVE VOLTAGE REGULATORS 5V, 6V, 8V, 9V, 10V, 12V, 15V, 18V, 20V, 24V.

FEATURES

Best Suited to a Power Supply for TTL and CMOS. Built-in Overcurrent Protective Circuit. Built-in Thermal Protective Circuit. Max. Output Current 150mA (Tj=25 ). Packaged in TO-92L.

MAXIMUM RATINGS (Ta=25 )

KIA79L05BP~

KIA79L24BP

BIPOLAR LINEAR INTEGRATED CIRCUIT

EQUIVALENT CIRCUIT

CHARACTERISTIC SYMBOL RATING UNIT

Input Voltage

KIA79L05BP KIA79L15BP

-35 V

KIA79L18BP KIA79L24BP

-40

Power Dissipation (Tc=25 )

800 mW

Operating Junction Temperature

-30 150

Operating Temperature

opr

-30 75

Storage temperature

stg

-55 150

harman/kardon

DVD 26 and 28/230 Service Manual

Page 56 of 76

DEPTH:0.2

123

1. COMMON

2. INPUT

3. OUTPUT

DIM MILLIMETERS

A B

D E F G H

L M N O

P Q

7.20 MAX

5.20 MAX

0.60 MAX

2.50 MAX

1.15 MAX

1.27

1.70 MAX

0.55 MAX _

14.00 0.50

0.35 MIN _

0.75 0.10 4

1.25

Φ1.50

0.10 MAX

12.50 0.50R

1.00S

TO-92L

GND

(1)

OUTPUT

(3)

INPUT

(2)

Page 57

Optic receiver modules

harman/kardon

DVD 26 and 28/230 Service Manual

Page 57 of 76

KSM-60 󱅢 T H 2·KSM-70 󱅢 T H 2

K O D E N S H I

The KSM-60󱅢TH2 consist of a PIN Photodiode of high speed and a preamplifier IC in the package as an receiver for Infrared remote control systems

F E A T U R E S

•One mold small package

•5 Volt supply voltage, low power consumption

•Shielded against electrical field disturbance

•High immunity against ambient light

•Easy interface with the main board

•TTL and CMOS compatibility

A P P L I C A T I O N S

•TV, VTR, Acoustic Devices, Air Conditioners, Car Stereo Units, Computers, Interior controlling

appliances, and all appliances that require remote c o n t r o l l i n g

R a t i n gS y m b o lP a r a m e t e r

5 . 5

- 1 0 ~ + 6 0

- 2 0 ~ + 7 5

( T a = 2 5℃U n l e s s

otherwise noted)

U n i t

MAXIMUM RATINGS

Supply Voltage Operating Temperature Storage Temperature Soldering Temperature

C C

T o p r .

T s t g . T s o l .

260(Max 5 sec)

D I M E N S I O N S

B.P.F CENTER FREQUENCY

V ℃ ℃ ℃

K S M -◯◯1 TH2 K S M -◯◯2 TH2 K S M -◯◯3 TH2 K S M -◯◯4 TH2 K S M -◯◯5 TH2

(Unit : mm)

N O T E

PIN configuration

6 0󱅢T H 2 7 0󱅢T H 2 ① V o u t V o u t ② G N D V c c ③ V c c G N D

B.P.F Center Frequency(kHz)Model NO.

4 0 . 0

3 6 . 7 3 7 . 9 3 2 . 7 5 6 . 9

ELECTRO-OPTICAL CHARACTERISTICS

P a r a m e t e r T y p .

Supply Voltage Current Consumption Peak Wavelength *1 B.P.F Center Frequency

Transmission Distance *1 H Level Output Voltage *1

L Level Output Voltage *1 H Level Output Pulse Width *1 L Level Output Pulse Width *1 Output Form

Note : *1. It specifies the maximum distance between emitter and detector that the output waveform satisfies the standard under the conditions below against the standard

t r a n s m i t t e r

1) Measuring place : Indoor without extreme reflection of light

2) Ambient light source : Detecting surface illumination shall be irradiate 200±50lx under ordinary white fluorescence lamp without high frequency lightning

3) Standard transmitter : Burst wave of standard transmitter shall be arranged to 50mVp-p under the measuring circuit

( T a = 2 5℃), Vcc=5.0V

S y m b o l C o n d i t i o n s M i n . M a x . U n i t .

λp

f o

V V T T

C C

O H O L

W H

W L

Input Signal=0

2 0 0±50l x

30cm over the ray

Burst Wave=600μs

P e r i o d = 1 . 2㎳

0°

±3 0°

a x i s

4 . 5

1 0

4 . 5

5 0 0 5 0 0

Active Low Output

5 . 0 1 . 2 9 4 0

3 7 . 9

5 . 0 0 . 1 6 0 0 6 0 0

5 . 5 2 . 5

0 . 5 7 0 0 7 0 0

V m A n m k H z

m m

μs μs

Page 58

harman/kardon

DVD 26 and 28/230 Service Manual

Page 58 of 76

Page 59

Block Diagram

harman/kardon

DVD 26 and 28/230 Service Manual

Page 59 of 76

LM1117/LM1117I

Connection Diagrams

SOT-223

Top View

TO-220

Top View

TO-252

Top View

10091904

10091938

10091901

TO-263

10091944

Top View

10091945

Side View

LLP

10091902

10091946

When using the LLP package

Pins 2,3&4must be connected together and

Pins 5,6&7must be connected together

Top View

Page 60

M29W160ET, M29W160EB

harman/kardon

DVD 26 and 28/230 Service Manual

Page 60 of 76

Figure 3. TSOP Connections

A15 A14 A13 A12 A11

A16 BYTE V

DQ15A–1 DQ7

A10 DQ14

37 36

DQ6 DQ13 DQ5 DQ12 DQ4 V

DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 G V

E A0

A9 A8

A19

W RP NC NC RB

A18 A17

A7 A6 A5 A4 A3 A2 A1

M29W160ET M29W160EB

24 25

AI06850

Page 61

2 PIN DESCRIPTION

harman/kardon

DVD 26 and 28/230 Service Manual

Page 61 of 76

Figure 2. 44-Pin TQFP Package Pinouts

ST72F324L, ST72324BL

RDI / PE1

PB0 PB1

PB2 PB3

(HS) PB4 AIN0 / PD0 AIN1 / PD1 AIN2 / PD2 AIN3 / PD3 AIN4 / PD4

RESET

/ ICCSEL

PA7 (HS)

PA6 (HS)

PE0 / TDO

OSC1

OSC2

44 43 42 41 40 39 38 37 36 35 34

1 2 3

ei2

ei0

ei3

6 7 8

9 10 11

12 13 14 15 16 17 18

AIN5 / PD5

ei1

19 20 21 22

SSA

AREF

(HS) PF2

BEEP / (HS) PF1

MCO / AIN8 / PF0

OCMP1_A / AIN10 / PF4

ICAP1_A / (HS) PF6

EXTCLK_A / (HS) PF7

PA5 (HS)

PA4 (HS)

SS_1

DD_1

PA3 (HS)

PC7 / SS / AIN15

PC6 / SCK / ICCCLK

PC5 / MOSI / AIN14

PC4 / MISO / ICCDATA

PC3 (HS) / ICAP1_B

PC2 (HS) / ICAP2_B

PC1 / OCMP1_B / AIN13

PC0 / OCMP2_B / AIN12

SS_0

DD_0

eix associated external interrupt vector

Page 62

ST72F324L, ST72324BL

harman/kardon

DVD 26 and 28/230 Service Manual

Page 62 of 76

PIN DESCRIPTION (Cont’d) Figure 3. 32-Pin SDIP Package Pinout

(HS) PB4

AIN0 / PD0

AIN1 / PD1

AREF

SSA

MCO / AIN8 / PF0

BEEP / (HS) PF1

OCMP1_A / AIN10 / PF4

ICAP1_A / (HS) PF6

EXTCLK_A / (HS) PF7

AIN12 / OCMP2_B / PC0

AIN13 / OCMP1_B / PC1

ICAP2_B / (HS) PC2

ICAP1_B / (HS) PC3

ICCDATA/ MISO / PC4

AIN14 / MOSI / PC5

Figure 4. 32-Pin TQFP 7x7 Package Pinout

ei3

ei1

ei0

ei2

PB3

PB0

PE1 / RDI

PE0 / TDO

VDD_2

OSC1

OSC2

RESET

PA7 (HS)

PA6 (HS)

PA4 (HS)

PA3 (HS)

PC7 / SS / AIN15

PC6 / SCK / ICCCLK

/ ICCSEL

(HS) 8mA high sink capability

eix associated external interrupt vector

AREF

MCO / AIN8 / PF0

BEEP / (HS) PF1

OCMP1_A / AIN10 / PF4

ICAP1_A / (HS) PF6

EXTCLK_A / (HS) PF7

AIN12 / OCMP2_B / PC0

SSA

PB0

PD1 / AIN1

PD0 / AIN0

PB4 (HS)

32 31 30 29 28 27 26 25

1 2 3 4 5 6 7 8

ei3

ei1

9 10111213141516

ICAP2_B / (HS) PC2

ICAP1_B / (HS) PC3

AIN13 / OCMP1_B / PC1

PB3

ei2

ICCDATA / MISO / PC4

AIN14 / MOSI / PC5

PE1 / RDI

ICCCLK / SCK / PC6

PE0 / TDO

ei0

AIN15 / SS / PC7

24 23 22 21 20 19 18 17

(HS) PA3

OSC1 OSC2 VSS_2 RESET V

/ ICCSEL

PA7 (HS) PA6 (HS) PA4 (HS)

(HS) 8mA high sink capability eix associated external interrupt vector

Page 63

SOIC (D)

3472C

SOIC (D)

Z3472

harman/kardon

DVD 26 and 28/230 Service Manual

Page 63 of 76

TL3472

HIGH-SLEW-RATE, SINGLE-SUPPLY OPERATIONAL AMPLIFIER

SLOS200G – OCTOBER 1997 – REVISED JULY 2003

Wide Gain-Bandwidth Product ...4 MHz

High Slew Rate . . . 13 V/µs

Fast Settling Time . . . 1.1 µs to 0.1%

Wide-Range Single-Supply Operation...4 V to 36 V

Wide Input Common-Mode Range Includes Ground (V

Low T otal Harmonic Distortion . . . 0.02%

Large-Capacitance Drive

CC–

)

CC–

D OR P PACKAGE

(TOP VIEW)

1OUT

/GND

1IN– 1IN+

CC+

2OUT 2IN– 2IN+

Capability . . . 10,000 pF

Output Short-Circuit Protection

description/ordering information

Quality, low-cost, bipolar fabrication with innovative design concepts is employed for the TL3472 operational

amplifier. This device offers 4 MHz of gain-bandwidth product, 13-V/µs slew rate, and fast settling time, without

the use of JFET device technology. Although the TL3472 can be operated from split supplies, it is particularly suited for single-supply operation because the common-mode input voltage range includes ground potential (V

). With a Darlington transistor input stage, this device exhibits high input resistance, low input of fset

CC–

voltage, and high gain. The all-npn output stage, characterized by no dead-band crossover distortion and large output voltage swing, provides high-capacitance drive capability , excellent phase and gain margins, low open-loop high-frequency output impedance, and symmetrical source/sink ac frequency response. This low-cost amplifier is an alternative to the MC33072 and the MC34072 operational amplifiers.

ORDERING INFORMA TION

PDIP (P) Tube of 25 TL3472CP TL3472CP

0°C to 70°C

PDIP (P) Tube of 25 TL3472IP TL3472IP

–40°C to 105°C

†

Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.

PACKAGE

†

Tube of 50 TL3472CD

Reel of 2500 TL3472CDR

Tube of 50 TL3472ID

Reel of 2500 TL3472IDR

ORDERABLE

PART NUMBER

TOP-SIDE MARKING

Page 64

harman/kardon

DVD 26 and 28/230 Service Manual

Page 64 of 76

Page 65

Product Specification

harman/kardon

DVD 26 and 28/230 Service Manual

Page 65 of 76

Low Cost Green-Mode PWM Controller for Flyback Converters SG6848

MARKING DI A G RA M S

PI N CONFIGURATION

M: Mask Version

MAYW

Y: Year; WW: Work Week

SG6848D

XXXXXXXYYWWV

XXXXXXX: Wafer Lot YY: Year ; WW: Week V: Assembly Location

GND

SOT-26

2 3

GATE

6 5

VDD

SENSE

ORDERING INFORMATION

Part Number PWM Frequency Package

SG6848T 70 kHz 6-Pin SOT-26

SG6848D 70 kHz 8-pin D IP-8

PIN DESCRI P TIONS

Name

GATE 1 / (6) Driver Output T he totem-pole output driver for driving the power MOSFET.

VDD 2 / (5) Supply Power supply.

NC 3 NC pin.

SENSE 4 / (4) Analog Input

RI 5 / (3)

NC 6 NC pin.

FB 7 / ( 2) Analog Input

GND 8 / (1) Supply Ground.

Pin No.

DIP-8 / (SOT-26)

Type F unction

Current s ense. This pin senses the voltage across a resistor. W hen the voltage reaches

the internal thr eshold, PWM output is disabled. This activates over-curr ent protection.

This pin also pr ovides current amplitude inf ormation for current-mode control.

A resistor connected from the RI pin to ground will generate a constant current source for

Analog

Input/Output

the SG6848. This current is used to charge an internal capacitor, to determine the

switching frequency. Increasing the resistance will reduce the amplitude of the current

source and reduce the switching frequency. A 95kΩ resistor R

current I

Feedback. The FB pin provides the output voltage regulation signal. It provides feedback

to the internal PW M comparator, so that the PW M comparator can control the duty cycle.

and a 70kHz switching frequency.

results in a 50uA constant

Page 66

harman/kardon

DVD 26 and 28/230 Service Manual

Page 66 of 76

Page 67

harman/kardon

DVD 26 and 28/230 Service Manual

Page 67 of 76

Page 68

harman/kardon

DVD 26 and 28/230 Service Manual

Page 68 of 76

Page 69

harman/kardon

DVD 26 and 28/230 Service Manual

Page 69 of 76

Page 70

harman/kardon

DVD 26 and 28/230 Service Manual

Page 70 of 76

Page 71

DVD Player Block Diagram (DVD 26, DVD 28, DVD 29, DVD 37 /230)

harman/kardon

DVD 26 and 28/230 Service Manual

Page 71 of 76

T.R MUTE

Control

C A

TRAVERSE UNIT

(SANYO PICK-UP HD62)

DV-342FV

OPEN/CLOSE &

SPINDLE MOTOR

& SLED

CONTROL

AM5888S

RF SERVO

ZR36707

16M Bit

FLASH u-COM

M29W160ET70N

27MHz

OSC

M P E G

ZR36778

SDRAM 64M

M12L64164A7T

EEPROM

24C08

VIDEO

EUR ONLY

3CH

VIDEO DRV.

BA7660FS

6CH.

VIDEO

DRV.

BH7862FS

Built in

filter

Coax. SPDIF OUT

AUDIO PCM OUT T.R BUFFER

FILTER

HDMI

TRANSM.

ZR36721

Comp.

S-Video

HDMI OUT

Optical

SMPS Ass'y

COP11840C

Remote

Sensor

Key Pad

8MHz

OSC

SYSTEM u-COM

ST72F324K2

SDRAM 64M M12L64164A7T

BUFFER

74HCT7007

Not used For DVD 37

VFD (CIG Type) 13BT229GINK

DSD DECODER

SAA7893

DSD OUT LT/RT

PCM/DSD CLK SELECT MUX.

74LVC157

AUDIO

DAC

CS4392

PHOTO COUPLER

KP1010B

+6dB OPAMP SW/C

SYSTEM

FL/FR

RL/RR

IN Out

Page 72

harman/kardon

DVD 26 and 28/230 Service Manual

Page 72 of 76

Page 73

harman/kardon

DVD 26 and 28/230 Service Manual

Page 73 of 76

Page 74

harman/kardon

DVD 26 and 28/230 Service Manual

Page 74 of 76

Page 75

harman/kardon

DVD 26 and 28/230 Service Manual

Page 75 of 76

Page 76

harman/kardon

DVD 26 and 28/230 Service Manual

Page 76 of 76

Harman Kardon DVD28 SERVICE MANUAL

Specifications and Main Features

Frequently Asked Questions

User Manual