PACKING AND PACKING PARTS.......6SCHEMATIC DIAGRAMS.........27
UNIT EXPLODED VIEW AND PARTS.7REVISION HISTORY................48
ELECTRICAL PARTS LIST.................8
Released 2007
Discontinued XXXXRev 0, 9/2007
CONTENTS
harman/kardon, Inc.
250 Crossways Park Dr.
Woodbury, New York, 11797
harman/kardon
Power for the Digital Revolution®
®
harman/kardon
Service manual DVD23EU
Page 2 of 48
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static"
can generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL
OTHER SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ESD device).
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and
impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction
and/or damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason
the adjustment point and installation
screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
5) Cleaning the lens surface
If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used
for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cotton swab should be used, taking care not to distort this.
6) Never attempt to disassemble the pick-up.
Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab. (Do
not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of
this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
Storage in conductive bag
NEVER look directly at the laser beam, and don’t let contact
fingers or other exposed skin.
Magnet
How to hold the pick-up
Conductive Sheet
Cotton swab
Pressure
Pressure
Drop impact
harman/kardon
Service manual DVD23EU
Page 3 of 48
NOTES REGARDING COMPACT DISC PLAYER REPAIRS
1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage,
components can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care must
be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong
magnetism is present, or where there is excessive dust.
2. Notes for repair
1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is
because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1MΩ)
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent
static electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.
Resistor
(1 Mohm)
Conductive
Sheet
Resistor
(1 Mohm)
Armband
harman/kardon
Service manual DVD23EU
Page 4 of 48
Technical Specifications
Applicable Disc:Disc formats: 5 inch (12 cm) or 3 inch (8 cm) DVD Video, Standard conforming DVD+RW, DVD+R, DVD-R,
DVD-RW and DVD-ROM, DivX,VCD, CD, CD-R, MP3,WMA, JPEG or CD-RW discs,
Regio code: DVD Movie disc with Code 2 or 0 only.
DVD-Layers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Single Layer, Dual Side/Dual Layer
Audio formats: Linear PCM, MPEG, Dolby Digital or DTS
Video Signal System:PAL/NTSC
Composite Video Output:1 V
p-p/75 Ohms, sync negative polarity
S Video Output:Y/Luminance: 1 V
p-p
/75 Ohms, sync negative polarity
C/Chrominance: 0.286 V
p-p
Component Video Output:Y: 1 Vp-p/75 Ohms, sync negative polarity
Cr: 0.7 V
p-p
/75 Ohms
Cb: 0.7 V
p-p
/75 Ohms
Analog Audio Output:2 Vrms max
Frequency Response:DVD (Linear PCM):2 Hz - 22 kHz +0/-0.5 dB (48 kHz sampling)
2 Hz - 44 kHz +0/-0.5 dB (96 kHz sampling)
CD:2 Hz - 20 kHz +0/-0.5 dB
Signal/Noise Ratio (SNR):113 dB (A-weighted)
Dynamic Range:DVD: 100 dB (18 Bit) / 105 dB (20 Bit)
CD/DVD: 96 dB (16 Bit)
THD/1kHz:DVD/CD: 0.0025 %
Wow & Flutter:Below Measurable Limits
AC Power:100 - 240 V/50 ~ 60 Hz
Power Consumption:2 Watts (Standby) /20 Watts (Max)
Dimensions (WxHxD):440 x 63 x 332 mm
Weight:3.7 kg
Depth measurement includes knobs and connectors.
Height measurement includes feet and chassis.
All specifications subject to change without notice.
DivX, DivX Certified, and associated logos are trademarks of DivX Networks, Inc and are used under license.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or diassembly is
prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER,
PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
harman/kardon
Service manual DVD23EU
Page 5 of 48
6
harman/kardon
Service manual DVD23EU
Page 6 of 48
11
10
9
3
8
7
1
2
3
5
16
4
15
14
13
12
NO. PART NO. Q'TY DESCRIPTION
1 01.00.BZ.X.W.292 1Carton box DVD23 EU
01.00.BZ.X.W.293 1Carton box DVD23 US
2 2Barcord Label
3 01.00.BZ.F.F.022 2Flat Polyfoam 310*168*28mm
4 02.03.118.DVD23 1completed remote control DVD23
5 01.00.BZ.D.Z.E019 1bag 8.4*24cmfor Remote control
6 01.00.BZ.F.P.E199 1Polyfoam HD970- left
01.00.BZ.F.P.E200 1Polyfoam HD970- right
7 1Main Unit
8 01.00.BZ.D.C.E068 1bag 540*495*T0.8mm for Main Unit
9 01.00.YS.SM1.314 1Owner manual DVD23 EU
01.00.YS.SM1.315 1Owner manual DVD23 US
1001.00.YS.FY3.455 1Guarantee card DVD23 for US
01.00.YS.FY3.457 1Warning card DVD23 for US
01.00.YS.FY3.456 1Safety instruction manual DVD23 for EU
1101.00.BZ.D.Z.E020 1Plastic bag 25*35cm for owner manual
1201.47.CNT.CTX.E028 1Audio/Video cable Yellow White Red, 1.2m
1301.47.CNT.CTX.027 1Remot control transmission cable φ3.5+φ3.5
(single channel), black, 1.2m
141.47.CNT.CTX.029 1S-video cable 1.2m
1501.14.DX.B.0005G 2battery 5#, GP brand
1601.00.BZ.D.Z.E001 1Plastic bag 15.5*23cm for AV cable
2
DVD 23 Packing instruction
18
harman/kardon
Service manual DVD23EU
Page 7 of 48
21
22
24
S2
S3
S2
S2
S3
S3
S2
S3
S2
S3
N1
S7
S9
S3
S2
N1
S2
S2S2
S2
S3
S3S3S3
S3
NO. PART NO. Q'TY DESCRIPTION
101.00.WJ.LM.060 1Aluminum ally wrap for disc tray DVD23
201.00.SJ.HD970.002 1HD970-Disc tray door
S3
301.00.SJ.DVD23.001 1DVD23-len on front panel
3a01.00.SB.051 1Metal logo DVD23
401.00.SJ.QT.001 1VFD filter 105.7mm*24.3mm*0.5
501.00.SJ.HD970.007 1HD970-Long decorate strip
601.00.SJ.HD970.001 1HD970-Short decorate strip
701.00.SB.034 1harman/kardon logo silver/blue color
801.00.SJ.HD970.011 1HD970-Power Indicator Cover
901.00.SJ.DVD23.002 1DVD23-front panel
2301.00.WJ.TJ.598 1DVD23-top cover
2401.47.CNT.ACX.E061 1Power cord with 300mm fixture EU
01.47.CNT.ACX.E035 1Power cord with 300mm fixture US
3a
S8S8
S101.00.WJ.JG.328 6Screw ST 3*6KBTTO
S201.00.WJ.JG.09310Screw ST 3*6PWMHC W=7
14
15
S4
S4
15
14
S301.00.WJ.JG.14513Screw ST 3*6PWBTTNI W=7
S401.00.WJ.JG.265 4Screw ST 3*8PWBTTC
S501.00.WJ.JG.14210Screw ST 3*6PAHC
S601.00.WJ.JG.089 1Screw ST 3*6PWAHC
S701.00.WJ.JG.321 5Screw ST 3*8PAHO
17
15
14
13
10
8
S1
7
6
S8
S1S1S1S1
S4
S5× 6
S5× 4
S4
S8
S6
11
S1
9
5
4
3
2
16
15
14
12
S801.00.WJ.JG.329 4Screw ST 4*8RTHO
S901.00.WJ.JG.324 2Screw PMO 3*8PMO
1 01.00.WJ.TJ.539DVD23 metals part
2 01.00.WJ.TJ.598DVD23 metals part
3 01.00.WJ.TJ.540DVD23 metals part
4 01.00.WJ.TJ.541DVD23 metals part
5 01.00.WJ.LM.060Aluminum ally wrap for disc tray
6
01.00.WJ.QT.0413 pin grounding piece
7
01.00.WJ.TJ.542heatsink
8
01.00.WJ.TJ.599heatsink
9
01.00.WJ.TJ.543heatsink
10 01.00.SJ.DVD23.002DVD23 plastic part
11 01.00.SJ.HD970.003HD970 plastic part
12 01.00.SJ.HD970.008HD970 plastic part
13 01.00.SJ.HD970.001HD970 plastic part
14 01.00.SJ.HD970.007HD970 plastic part
15 01.00.SJ.HD970.011HD970 plastic part
16 01.00.SJ.HD970.002HD970 plastic part
17 01.00.SJ.DVD23.001DVD23 plastic part
18 01.00.SJ.DVD22.010DVD22 plastic part
19 01.00.SJ.SK.008IR receiver support
20 01.00.SB.034harman/kardon logo
21 01.00.SB.051Metal logo
22 01.00.SJ.QT.001VFD filter
23 01.00.DP.HM.E158Pedestal underlay
24 01.00.DP.HM.E142sponge
25 01.00.WJ.JG.126Screw map4
26 01.00.FZ.QT.122Plastic fastener
27 01.00.WJ.TJ.569Alumium fastener
28 01.00.DP.JY.E087Insulated piece for power board
29 01.00.DP.JY.E072Insulated underlay
30 01.47.CNTLJX.7175Connect cable
31 01.47.CNT.LJX.7194Connect cable
32 01.47.CNT.LJX.7096Connect cable
33 01.47.CNT.ACX.E061Connect cable
35 01.47.CNT.LJX.7195Connect cable
36 01.47.CNT.LJX.7193Connect cable
37 01.47.CNT.LJX.7196Connect cable
SAN1
1
1 HD970-RE02
1 HD970-RE03
1 HD970-RE04
1 HD970-RE05
1 HD970-RE06
1 HD970-RE07
1 DVD23-RE01
4
1 SZ003
1
1 stick on len for front panel
1 HD970-H01
4 place under the pedestal
3 for VFD (2)\ for 24pin flatcable(1)
2 fix the AC cord
3 with φ
1 stick on chassis
2 place on 1824C-1B
1 connect power supplier board and AV board
1 connect power supplier board and mainboard
1 connect power supplier board
1
1 connect power supplier board and front panel board
1 connect loader and mainboard
1 connect loader and mainboard
2
1 connect front panel board
1 connect loader and mainboard
2 connect mainboard and AV board
1 connect mainboard and front panel board
1
1
3×40 pyrocondensation cover
place on
SMPS
place on
SMPS
place on
SMPS
place on
SMPS
bronzing
45 01.00.BZ.X.W.292Carton box
harman/kardon
Service manual DVD23EU
Page 9 of 48
47 01.00.BZ.F.P.E199Polyfoam
48 01.00.BZ.F.P.E200Polyfoam
49 01.00.BZ.F.F.022Flat Polyfoam
50 01.00.BZ.D.C.E068Plastic bag
51 01.00.BZ.D.Z.E020Plastic bag
52 01.00.BZ.D.Z.E001
53 01.00.BZ.D.Z.E019
54 01.00.YS.SM1.314Owner manual
57 01.00.YS.FY3.456Safety instruction manual
59 01.00.YS.TZ.T.068Laser label
60 01.00.YS.TZ.T.057Laser label
61 01.00.BP.QT.E157top cover label
62 01.47.CNT.CTX.E028
63 01.47.CNT.CTX.027Remot control transmission cable
64 01.47.CNT.CTX.029S-video cable
65 01.14.DX.B.0005Gbattery
66 02.03.118.1823CSMPS board with components
67 02.03.118.1824C1AFront panel board with components
68 02.03.118.1824C1BFront panel board with components
69 02.03.118.1825CMainboard with components
70 02.03.118.1826CAV board with components
Plastic bag15.5*23cm
Plastic bag8.4*24cm
Audio/Video cableYellow White Red, 1.2m
DVD23 Component List for Power Supply Board (1823C)
DVD23 EU Component List
DVD23
HD970- left
HD970- right
310*168*28mm
540*495*T0.8mm
25*35cm
DVD23
DVD23
Laser precausion mark
Laser precausion guide
DVD23
φ3.5+φ3.5(single channel), black, 1.2m
1.2m
5#, GP brand
1823C
1824C-1A
1824C-1B
1825C
1826C
1
1
1
2
1 for unit
2 for owner manual
1 for AV cable
1 for remote control
1
1
1 stick on loader
1 stick on loader
1 stick on top cover
1
1
1
2
1
1
1
1
1