Page 1
DVD 22 / DVD 22 B Digital Versatile Disc Player
OWNER’S MANUAL
Power for the Digital Revolution
®
Page 2
Table of Contents
2
3 Introduction
4 Terminology
5 Features, Packing List
6 Front Panel Controls
7 Front Panel Information Display
8 Remote Control
10 Rear Panel Connections
11 Setup and Connections
11 to a Stereo TV and Stereo or Pro Logic
Amplifier/Receiver
12 to a Dolby Digital/DTS Amplifier/Receiver
13 to a TV or monitor with SCART or
Component Connectors
14 Remote Control
15 Digital Audio Connections
16 Playback Basics
16 Basic Play
16 Playback Features
17 System Set-up
17 System Settings
18 Audio Settings
18 Video Settings
18 Video Adjustment
19 Test Screen
19 Test Screen
19 TV Picture Adjustment
20 Player Menu
20 Using the Status Bar
20 Player Menu
20 Information Displays
20 Programmed Play
21 DVD Language Codes
22 Specifications
Declaration of Conformity
We, Harman Consumer Group International
2, Route de Tours
72500 Château-du-Loir,
FRANCE
declare in own responsibility, that the product described in
this owner’s manual is in compliance with technical
standards:
EN 55013:2001
EN 55020:2002
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:2001
EN 60065:2002
NOTE: This player is designed and manufactured for compatibility with Region
Management Information that is encoded on
most DVD discs.This player is designed only for
Harman Consumer Group International
Jurjen Amsterdam
07/04
playback of discs with Region Code 2, or for
discs that do not contain Region Code information. If there is any other Region Code on a
disc, that disc will not play on the DVD.
2 TABLE OF CONTENTS
Page 3
Introduction
Thank you for choosing the
Harman Kardon DVD
The DVD is a multipurpose DVD player, capable of
playing both DVD-Video discs and conventional
CD audio discs with the highest fidelity and
access to future software upgrades via the
Internet. Along with conventional DVD-Video and
CD audio discs, the DVD is also compatible with
MP3, WMA, JPEG and most recordable CD and
DVD formats as well as VCD discs.
To enable you to get the maximum quality from
DVDs, the DVD is equipped with the latest in
design techniques, including advanced 10-bit
video digital-to-analog converters (DAC) and
Video (composite), S-Video and RGB video (RGB
via SCART) outputs, to ensure that you get all the
quality inherent in today’s DVD medium. For optimum playback of NTSC and PAL DVD with compatible high-definition display devices, DVD is
equipped with progressive component video outputs.
In addition, Harman Kardon’s audio heritage
continues into the digital video era with audiophile-grade Wolfson DACs to ensure that the
audio quality matches the superb video. Of
course, both coaxial and optical digital audio
outputs are available for direct connection to A/V
receivers or processors so that you may take
advantage of Dolby Digital* and DTS
®
soundtracks.When playing audio CDs, the playback
quality is state-of-the-art, matching that of the
finest players available.
A wide range of programming features makes it
easy to program an evening’s worth of entertainment. When playing DVDs, easy-to-understand
on-screen menus and icons make it simple to
change languages, soundtracks, subtitles or
aspect ratio, while a parental-lock function
enables you to control which discs may be
viewed by younger members of the household.
DVD players are among the fastest growing consumer electronics products ever brought to market, but this may, nevertheless, be the first DVD
player you’ve owned. Although many of the features of the DVD resemble those of standard CD
players, there are a number of functions that you
may be unfamiliar with. To ensure that you are
able to take advantage of all the power and flexibility the DVD has to offer, we encourage you to
review this quick setup manual. That small
investment of your time will pay major dividends
in the enjoyment you will get from proper use of
the DVD.
■ Plays a Wide Range of Video and Audio
Formats, Including DVD-Video Discs,
VCD, Standard CD Audio Discs, CD-R/RW,
DVD-R/RW, DVD-+R/RW, Audio Discs and
MP3 Discs
■ High-Quality Video Playback 10-Bit
DACs, Progressive Scan and Component
Video Outputs
■ Dolby Digital and DTS Data Signal
Output Through Both Optical and
Coaxial Digital Audio Connections
■ Audiophile-Grade Wolfson Output DACs
for the Finest Audio reproduction
■ Easy-to-Use On-Screen Navigation
System
®
■ Playback of MP3 and Windows
WMA
Audio Discs and JPEG image files
■ Simultaneous Playback of MP3 and JPEG
files
■ Extensive Programming Capability for
Audio and Video Discs
■ Parental Lock Controls Prevent
Unauthorized Viewing of Restricted
Movies
■ Multiple Options for Language,
Soundtrack and Subtitle Selection
■ Multiple-Angle Capabilities With
Specially Encoded DVD Discs
■ Backlit, Ergonomically Designed Remote
Control
INTRODUCTION 3
Page 4
Terminology
Terminology
Since they share some of the characteristics and
technology of CD players, many of the terms and
operational concepts used in a DVD player are
similar to what you may be familiar with from CD
players and changers, or older video disc formats
such as Laser Disc. However, if this is your first
DVD product, some of the terms used to describe
the features of a DVD player may be unfamiliar.
The following explanations should solve some of
the mysteries of DVD, and help you to enjoy all
the power and flexibility of the DVD format and
the DVD.
With the arrival of DVD, disc data capacity has
increased dramatically. On a DVD Video disc most
of this capacity is taken up by MPEG 2 video and
the multichannel movie soundtrack in Dolby
Digital and/or DTS.This information is compressed.
Aspect Ratio: This is a description of the width
of a video image in relation to its height. A conventional video screen is four units wide for every
three units of height, that’s why the ratio is called
”4:3”. Newer wide aspect ratio video displays
are 16 units wide for every nine units of height,
making them more like the screen in a movie theater. The program material on a DVD may be
recorded in either format and, in addition, you
may configure the DVD to play back in either format, depending on the features recorded on a
disc.
Title: For a DVD, a title is defined as an entire
movie or program.There can be as many chapters
within a title as the producers decide to include.
Most discs include only one title, but some may
have more than one, to give you a “Double
Feature” presentation.
Chapter: DVD programs are divided into chapters and titles. Chapters are the sub-sections programmed into a single title on a disc. Chapters
may be compared to the individual tracks on an
audio CD.
RGB Video: This is a new form of video signal
that eliminates many of the artifacts of traditional
composite video signals by splitting the signal
into the three fundamental colors Red, Green and
Blue (RGB). With an RGB connection (via SCART),
you will see greater picture resolution and eliminate many picture imperfections such as the
moiré patterns often seen on checkered patterned cloths. However, in order to benefit from
RGB video, you must have a video display with an
RGB compatible SCART input.
Progressive scan: DVD offers progressive scan
video outputs for use with compatible high-resolution televisions and projectors. Before DVD, no
consumer medium could store, transmit or display
video with full resolution. To conserve bandwidth,
analog compression (interlacing) is employed: first
the odd-numbered lines of a frame are displayed,
followed by the even-numbered lines.The result is
that only half of the video image is drawn at one
time; the viewer's brain must reassemble the complete image.This is acceptable, if the monitor is
not too large and if there is not too much motion
in the image. Large displays and fast-moving
images reveal the limitations of this system.
Thanks to DVD's immense data capacity, images
are now stored intact (progressively), so that all
the lines in each frame (odd and even) are shown
at the same time. But because most TV's cannot
handle a progressive signal, all current DVD players generate an interlaced output for compatibility. Now, the Harman Kardon DVD is among the
select few DVD players with true progressive scan
video output (NTSC and PAL) for use with compatible TV's and CRT projectors and with all plasma, LCD and DLP display devices via the component video output. The result is 40% greater light
output than a conventional TV and a stunningly
detailed high definition image, along with an
almost complete absence of visible scanlines and
motion artifacts. Of course, traditional Y/Pr/Pb
component video, SCART, S-Video and composite
video outputs are included for use with conventional televisions and projectors.
Multiple Angle: DVDs have the capability to
show up to four different views of the same
scene in a program. When a disc is encoded with
multiple-angle information, pressing the Angle
button will enable you to switch between these
different views. Note that at present, few discs
take advantage of this capability and, when they
do, the multiple-angle technology may only be
present for short periods of time within the disc.
Producers will usually insert some sort of icon or
graphic in the picture to alert you to the availability of multiple viewing angles.
Reading: This is a message that you will see
after you´ve loaded the disc and the tray has
closed. It refers to the fact that the player must
first examine the contents of the disc to see if it is
a CD or DVD, and then extract the information
about the type of material on the disc, such as
languages, aspect ratios, subtitles, number of
titles and more.The slight delay while the contents of the disc are read is normal.
Resume: The operation of the Stop Button on
the DVD works differently from what you are
used to on CD players. On a traditional CD player,
when you press the Stop button, the unit does
just that: it stops playback. On a CD player, when
you press the start button again, the disc starts
from the beginning. With the DVD, however, you
have two options when playing DVD discs.
Pressing Stop once will stop playback, but it actually puts the unit in the Resume mode.This
means that you can turn the machine off and,
when you press play the next time, the disc will
resume or continue from the point on the disc
where the Stop button was pressed. This is helpful if you are watching a movie and must interrupt your viewing session but wish to pick up
where you left off. Pressing the Stop button twice
will stop the machine in a traditional manner
and, when the disc is played again, it will start
from the beginning.
In resume mode, the cover of the DVD will be
displayed, if available. Otherwise, the
Harman Kardon screen will appear.
4 TERMINOLOGY
Page 5
Features
High quality video
• Advanced sophisticated 10-bit MPEG-2 video
decoding circuits.
• Direct RGB output via SCART (selectable) for
optimum video performance. SCART connector
also configurable for Composite Video output.
• Test screen videos available for testing video
performance and setup.
• Pure PAL with NTSC disc due to true
NTSC/PAL conversion.
• Dual-layer compatibility for extended play
DVD.
• Progressive Scan component video ouputs
(NTSC and PAL)
• Playback of JPEG image files
High quality digital audio
• By connecting a DTS (Digital Theater Systems)
or a Dolby Digital decoder, you can enjoy high
quality 5.1 digital surround sound from DTS or
Dolby Digital discs.
• With linear PCM audio at 16-24 bits and
44-96 kHz (also on digital output, see table
page 15), audio quality exceeding that of CD
becomes possible.
• Optical and coaxial digital audio output.
Many convenient features
• On-Screen Menu lcons for disc information or
player information and access to many major
functions of this unit.
• Subtitles may be displayed in one of numerous
languages*.
• The multi-angle function allows you to choose
the viewing angle of scenes which were shot
from a number of different angles (Limited to
DVD’s recorded with multiple camera angles.)
• Multiple options for dialog language and
soundtrack selection (limited to DVD’s recorded with multiple dialog languages or soundtracks).
• Parental lock settings to prevent play of discs
unsuitable for some audiences [DVD only].
• Intuitive menu operating system.
• 4 step Zoom during play and pause.
• Backlit, ergonomically designed remote
control.
• Future software upgrades accessible via
Internet. (See information below.)
* The number of languages recorded depends
on the software.
Compatible with CD
as well as DVD
• The DVD will play any conventional Audio CD or
recordable (CD-R) or erasable CD (CD-RW)
bearing the logos shown here, MP3,WMA (v8)
or any VCD or DVD-Video with the region code
0 or 2.
Disc formats supported
by this player
The unit can play the following disc formats
(8 cm and 12 cm size):
• DVD-Video
• DVD-R
• DVD-RW
• DVD+R
• DVD+RW
• CD
• CD-R
• CD-RW
• VCD
• S-VCD
NOTE: Due to differences in the format of
certain discs, it is possible that some discs may
include a mix of features that are not compatible
with the DVD. Similarly, although the DVD is
capable of a wide range of features, not all discs
include every capability of the DVD system. For
example, although the DVD is compatible with
multi-angle discs, that feature is only possible
when the disc is specially encoded for multipleangle play. In addition, the DVD is capable of
playing back both Dolby Digital and DTS soundtracks, but the number and types of tracks available will vary from disc to disc. To make certain
that a specific feature or soundtrack option is
available, please check the options noted on the
disc jacket.
■ Playback capability for CD-R, CD-RW, WMA,
JPEG, MP3,VCD/SVCD, DVD-R, DVD+R, DVDRW and DVD+RW discs may vary due to
variations in the quality of the disc and the
recorder used to create the disc.
Upgradeability via Internet
The ”firmware” controlling the functionality of
the Harman Kardon DVD is fully upgradeable. In
the event of future improvements to its
operations and features, it will be possible to
download firmware upgrades from
www.harmankardon.com/International/
All you have to do is create a CD-R with the
data and insert it in the DVD for an automatic
upgrade.
Packing List
1 Harman Kardon DVD Player
1 Remote control
2 AA batteries
1 A/V cable for stereo analog audio and
composite video
1 S-Video cable
1 remote extension cable
1 owner's manual
FEATURES 5
Page 6
Front Panel Controls
DVD 22
1 3 4 5 6 7 8
Main Information Display
1
Power On/Off (Standby)
2
Eject
Main Information Display: This display
3
4
5
Play
Pause
Stop
delivers messages and status indications to help
you operate the DVD player.
1
Power On/Off (Standby): Press the button
once to turn the DVD player on, press it again to
put the unit in the Standby mode.
2
Eject: Press this button to open or close the
Disc Tray.
3
Play: Press to initiate playback or to resume
playback after Pause has been pressed.
6
Skip/Search (Previous)
7
Skip/Search (Next)
8
Dimmer
4
Pause: Press this button to momentarily
pause playback. To resume playback, press the
button again. If a DVD is playing, action will
freeze and a still picture will be displayed when
the button is pressed.
5
Stop: Press this button once to place the
disc in the Resume mode, which means that
playback will stop, but as long as the tray is not
opened or the disc changed, DVD playback will
continue from the same point on the disc when
the Play Button is pressed again. Resume will
also work if the unit was turned off. To stop a
disc and have play start from the beginning,
press the button twice.
2
6
Skip/Search (Previous): Press this button
to move backward through the music tracks on
a CD disc or the chapters on a DVD disc. Keep
the button pressed to search backwards at one
of the available speeds.
7
Skip/Search (Next): Press to move forward
through the music tracks on a CD or the chapters on a DVD disc. Keep the button pressed to
search forwards at one of the available speeds.
8
Dimmer: Press this button to reduce the
brightness of the Information Display by 50% or
to turn the display off completely in the
following order: FULL BRIGHTNESS ➔ HALF
BRIGHTNESS ➔ OFF ➔ FULL BRIGHTNESS.
6 FRONT PANEL CONTROLS
Page 7
Front Panel Information Display
L
A
JPEG MP3
VCD
PROG
DVD
WMA
B
A Disc Type Indicators
B Playback-Mode Indicators
C Progressive Scan Indicator
D Parental Lock Indicator
E Time Indicators
A Disc Type Indicators: The DVD, CD, VCD,
MP3, WMA or JPEG indicator will illuminate to
show the type of disc currently being played.
B Playback-Mode Indicators: These indica-
tors light to show the current playback mode:
› Lights when a disc is playing in the normal
mode
H
Lights when the disc is in the Fast Search
Forward mode. The on-screen banner display
indicates the selected speed (2x, 8x, 16x, 100x).
1
Lights when the disc is paused.
G
Lights when the disc is in the Fast Search
Reverse mode.The on-screen banner display
indicates the selected speed (2x, 8x, 16x, 100x).
C Progressive Scan Indicator: This indicator
lights when the unit sends out a progressive
scan signal.
D Parental Lock Indicator: This indicator
lights when the parental-lock system is engaged
in order to prevent anyone from changing the
rating level without a code.
KIG
A-B
V. OFF
PBC
HOUR
REPEAT
TRACK
O
H
1 ALL
CHAPTER
J
RANDOM
TITLE
NE
F Test Indicator
G V-OFF Indicator
H Repeat Indicators
I VCD Playback Control Indicator
J Random Indicator
E Time Indicators: These positions in the
indicator will show the running time of a DVD in
play.When a CD is playing, these indicators will
show the current track time, time remaining in
the current track, or the total remaining time on
the disc.
NOTE: The Indicators NOE will also display
text messages about the DVD’s status, including
Reading when a disc is loading,
STANDBY when the unit is turned off, and
Disc Error when a disc not compatible
with the DVD is put into the play position.
F Test Indicator: This indicator lights when
the TV test screen is activated.
G V-OFF Indicator: This indicator lights when
the unit's video output has been turned off by
pressing the V-OFF button on the remote control.
H Repeat Indicators: These indicators light
when any of the Repeat functions are in use.
F
TEST
MIN
K A-B Repeat Indicator
L Program Indicator
M Angle Indicator
N Title Indicators
O Chapter/Track Number Indicators
I VCD Playback Control Indicator: This
indicator lights when the playback control function is turned on with VCDs.
J Random Indicator: This indicator lights
when the unit is in the Random Play mode.
K A-B Repeat Indicator: This indicator lights
when a specific passage for repeat playback has
been selected.
L Program Indicator: This indicator lights
when the programming functions are in use.
M Angle Indicator: This indicator blinks when
alternative viewing angles are available on the
DVD currently playing.
N Title Indicators: These two positions in the
display will show the current title number when
a DVD disc is playing.
O Chapter/Track Number Indicators: When
a DVD disc is playing, these two positions in the
display will show the current chapter. When a
CD disc is playing they will show the current
track number.
D
CM
P. PROG
SEC
FRONT PANEL INFORMATION DISPLAY 7
Page 8
Remote Control Functions
0
POWER ON
1
POWER OFF
2
SUBTITLE
3
TITLE
4
ANGLE
5
AUDIO
6
ENTER
7
OPEN/CLOSE
8
OSD
9
ARROWS
A
INFO
B
MENU
C
PAUSE
D
STATUS
E
SKIP/STEP (PREVIOUS)
F
SKIP/STEP (NEXT)
G
PLAY
H
SEARCH/SLOW REVERSE
I
STOP
J
SEARCH/SLOW FORWARD
K
DISPLAY
L
PIC +/PIC -
M
ZOOM
N
PLAYLIST
O
RANDOM
P
A-B Repeat
Q
V.OFF
LIGHT
NUMERIC KEYS
REPEAT
CLEAR
N
5
9
G
H
Q
3
A
0
7
C
E
I
K
O
1
2
8
6
B
D
F
J
L
M
4
P
8 REMOTE CONTROL FUNCTIONS
DVD 22
Page 9
Remote Control Functions
0
POWER ON: Turns on the player when it is
in standby mode (Harman Kardon logo appears
on screen).
1
POWER OFF: Turns off the player to standby mode.
2
SUBTITLE: When a DVD is playing, press to
select a subtitle language or to turn subtitles off.
3
TITLE: When a disc is playing, press to
show the number of the title currently played.
Press TITLE again to jump to the subsequent title
(with the next title number) on the disc. Note
that this function works (most times) even if title
jump is prohibited by a DVD´s playback control.
4
ANGLE: Press to access various camera
angles on a DVD (If the DVD contains multiple
camera angles).
5
AUDIO: Press to access various audio
languages on a DVD (If the DVD contains
multiple audio streams).
6
ENTER: Press this button to activate a setting or option
7
OPEN/CLOSE: Press to open or close the
disc tray.
8
OSD: Press to access the On Screen Display
Menu
9
ARROW buttons (M/N/K/L): Use to
move the cursor in the OSD.
A
INFO: Press once for detailed informations
on the disc playing (Video/Audio Bit rate, Movie
aspect ratio and others), press again for current
player settings made. Note that the unit doesn´t
react on any transport button as long as the info
menu is displayed. Press again to remove information from screen.
B
MENU: Displays the actual DVD Disc Menu
on the TV screen in play mode.
C
PAUSE: Freezes a picture (with DVD/VCD)
and pauses the playback signal (CD) when a disc
is playing. Press again for normal playback.
D
STATUS: Press while a disc is playing to
view banner display. Use the ARROW buttons to
move through the different features in the
Banner Display.When a symbol is highlighted,
press ENTER on the remote to select it.
E
SKIP/STEP (Previous): Press to go to
beginning of current track. Press again quickly to
go to beginning of previous track. After pressing
the PAUSE button, each press of this button will
move the image in reverse frame by frame.
F
SKIP/STEP (Next): Press to go to beginning of next track. After pressing the PAUSE
button, each press of this button will move the
image forwards frame by frame.
G
PLAY: Begins to play disc (closes disc tray
first, if it is open.)
H
SEARCH/SLOW (REV): Allows you to
search in reverse through a disc while it is in
play mode. Each time you press this button, the
search speed changes as indicated by a number
of arrows on the right top of your screen.
After pressing the PAUSE button, each press of
this button will change the slow down speed
indicated by a number of arrows in the right top
of the screen.
I
STOP: Stops playing a disc.When a disc is
playing, if you press STOP and PLAY, the disc will
resume play, i.e. it will start from the same point
on the disc where the unit was stopped. If you
press STOP twice and the PLAY button, the disc
will start play from the beginning.
J
SEARCH/SLOW (FWD): Allows you to
search forward through a disc while it is in play
mode. Each time you press this button, the
search speed changes as indicated by a number
of arrows on the right top of your screen.
After pressing the PAUSE button, each press of
this button will change the slow down speed as
indicated by a number of arrows in the right top
of the screen.
K
DISPLAY: Press to change the brightness of
the front panel display or to turn the display off
completely in the following order: FULL BRIGHTNESS ➜ HALF BRIGHTNESS ➜ OFF ➜ FULL
BRIGHTNESS
L
PIC+/PIC-: Pressing these buttons in JPEG
mode will move to the previous or next image.
M
ZOOM: When a DVD or VCD is playing,
press this button to zoom the picture so that it is
enlarged. There are 4 steps to the zoom function, each progressively larger. Press through
each of the zoom stages to return to a normal
picture.
N
PLAYLIST: Press this button to change the
playback order of the disc.
O
RANDOM: Press for RANDOM playback in
random order.
P
A-B: Press to select section A-B and to play
repeatedly.
Q
V.OFF: Press to turn off video output for
improved performance from audio-only discs.
Press again to restore video output.
LIGHT: Press to illuminate remote
controller.
NUMERIC KEYS: Select numbers by
pressing these buttons.
REPEAT: Press to go to the Repeat menu.
You can repeat a chapter, track or the entire
disc.
CLEAR: Press to remove the Banner menu
from the screen.
REMOTE CONTROL FUNCTIONS 9
Page 10
Rear Panel Connections
¡
Optical Digital Output
™
Coaxial Digital Output
£
Analog Audio Outputs
¢
Composite Video Output
¡
Optical Digital Output: Connect this jack
to the optical digital input of an A/V receiver or
surround processor for Dolby Digital, DTS or
PCM audio playback.
™
Coaxial Digital Output: Connect this jack
to the coaxial digital input of an A/V receiver or
surround processor for Dolby Digital, DTS or
PCM audio playback.
NOTE: The coaxial digital output should only be
connected to a digital input. Even though it is
the same RCA-type connector as standard analog audio connections, DO NOT connect it to a
conventional analog input jack.
£
Analog Audio Outputs: Connect these
jacks to the analog audio input on an A/V
receiver or surround processor for analog audio
playback.
¢
Composite Video Output: Connect this
jack to the video input on a television or video
projector, or to a video input on an A/V receiver
or processor if you are using that type of device
for video input switching.
MODEL NO. DVD 22
∞
S-Video Output
§
Component Video Outputs
¶
Scart TV Output
•
Remote Control Output
∞
S-Video Output: Connect this jack to the
S-Video input on a television or video projector,
or to an S-Video input on an A/V receiver or
processor if you are using that type of device for
S-Video input switching.
§
Component Video Outputs: These outputs carry the component video signals for connection to display monitors with component
video inputs. For standard analog TV's or projectors with inputs marked Y/Pr/Pb or Y/Cr/Cb, connect these outputs to the corresponding inputs.
If you have a high-definition television or projector that is compatible with high scan rate progressive video, connect these jacks to the “HD
Component” inputs. Note that if you are using a
progressive scan display device, then
”Progressive” must be selected in the Video Setup Menu in order to take advantage of the progressive scan circuitry. See page 17 for more
information on progressive scan video.
IMPORTANT: These jacks should NOT be connected to standard composite video inputs.
¶
SCART OUT (TV): If your TV has a SCART
socket, you can connect a SCART cable to your
TV and to your DVD Player for improved video
quality.The SCART cable carries both audio and
video.You can select Composite Video or RGB
video for that SCART connector’s video output
signal.
976354210 8
ª
Remote Control Input
‚
AC Power Cord
•
Remote Control Output: Connect this
jack to the infrared (IR) input jack of another
compatible Harman Kardon remote controlled
product to have the built-in Remote Sensor on
the DVD provide IR signals to other compatible
products.
ª
Remote Control Input: Connect the output of a remote infrared sensor, or the remote
control output of another compatible Harman
Kardon product, to this jack.This will enable the
remote control to operate even when the front
panel Remote Sensor on the DVD is blocked.
This jack may also be used with compatible IR
remote control-based automation systems.
‚
AC Power Cord: Connect this plug to an
AC outlet. If the outlet is controlled by a switch,
make certain that it is in the ON position.
Note: You’ll find more details about all
Audio/Video connections under Setup and
Connections on the following pages.
10 REAR PANEL CONNECTIONS
Page 11
Setup and Connections
■ Ensure that the power switch of this unit and
other equipment to be connected is set to off
before commencing connection.
■ Do not block ventilation holes of any of the
equipment and arrange them so that air can
circulate freely.
■ Read through the instructions before
connecting other equipment.
■ Ensure that you observe the color coding
when connecting audio and video cables.
Connecting to a stereo TV and stereo or Pro Logic Amplifier/Receiver
TV
To S-Video input connector
To stereo audio input connector (Red/White) on
the TV or Stereo/Pro Logic Amplifier/Receiver
DVD
Notes:
■ The Video output (yellow) combines the complete video signal (composite) and sends it to
the TV (or to the AV Receiver) by one line
only. Use the Video output, when your TV set
is equipped with a Video input jack only.
■ The S (separate) video output connector separates the color (C) and luminance (Y) signals
before transmitting them to the TV set in
order to achieve a sharper picture. Use the
S-video cable when connecting the player to
a TV equipped with an S-video input
To Video input
connector (Yellow)
MODEL NO. DVD 22
for improved picture clarity. Never connect
both outputs,Video and S-Video, to your TV
or AV Receiver, only one of them.
■ Most European TV´s are equipped with SCART
connectors rather than with a normal video
input (yellow cinch). In that case the SCART
connection should be used, providing the
audio signal too. Separate analog audio connections to TV are needed only if your TV is
connected to the video or S-video output.
To power outlet
(AC 230V/50 Hz)
■ When the audio signal is to be fed to a stereo
or Pro Logic amplifier/decoder or receiver
rather than to the TV, connect the Audio Out
jacks to any normal audio input on your
amplifier/decoder/receiver. The DVD will
”downmix” Dolby Digital recordings to Pro
Logic, available on these connectors, all analog surround or stereo signals will be fed to
them directly.
You can also select the audio and video signals of all your video devices with your AV
Receiver/Amplifier. For more information see
”Note” on next page.
SETUP AND CONNECTIONS 11
Page 12
Setup and Connections
Connecting to a receiver/amplifier with Dolby Digital (AC-3) or DTS (Digital Theater Systems) decoder
When DVD´s encoded in Dolby Digital or DTS are
played, the Dolby Digital or DTS bitstream is output from the player’s OPTICAL or COAXIAL digital audio output. When the player is connected
to a Dolby Digital or DTS decoder, you can enjoy
theater-quality audio in your home. An optical
digital audio cable or coaxial audio cable (both
optional) is required for these connections, as
shown below. Only one connection is needed,
not both at the same time.
To audio input connector
(Red/White, optional only, see Note above)
■ Note: With multiple video sources, your
Audio/Video device can be used for selecting
the video signal and routing it to the TV.
Connect the video or S-video output of the
DVD player (whatever is provided with your
device) to the video or S-video input on your
device and the video/S-video output of this
device to your TV. For more details, see the
manual of your Audio/Video amplifier/receiver.
TV
To S-Video input connector
■ Note for Analog Audio: The connection
from Audio Out to the TV is optional only.
Normally you´ll hear the sound from your
AV-system´s speakers, so the TV volume
should be completely turned down. If you
plan to use your DVD player also without
having to turn on your complete system, this
connection must exist, then you can turn up
the TV´s volume as needed.
DVD
To coaxial audio input connector
To optical audio input connector
Dolby Digital or DTS decoder
To Video input
connector (Yellow)
To power outlet
(AC 230V/50 Hz)
MODEL NO. DVD 22
Front Speaker (Left/Right) Center Speaker Surround Speaker (Left/Right) Subwoofer
12 SETUP AND CONNECTIONS
Page 13
Setup and Connections
Connecting to a TV or monitor with SCART or Component connectors
Important Notes on SCART and RGB
format:
■ Your DVD is equipped with a SCART connector for direct connection to the TV.
■ The SCART connector provides the video
signal as well as audio (stereo L/R) signals.
■ The SCART connector for the TV provides the
composite video signal or the direct RGB signal, delivering the best video performance
possible, selectable in the Setup menu.To
view RGB video on your TV, the RGB compatible SCART connector on the TV must be used
and the DVD´s TV SCART connector must be
set to ”RGB”.
Note that with RGB video the color intensity
cannot be adjusted with most TVs.
■ When the RGB video signal is used, DVD´s
recorded with the NTSC format (with regional
code 0 or 2) can be viewed even on nonNTSC compatible TVs.
TV or Monitor
Component Video Connection
If the video display has component video inputs,
connect the Component Video Outputs on the
DVD to the corresponding input jacks on your
television. If you are using a progressive scan
television or projector, you must also change the
Scan Type in the DVD player's Video Set-Up
Menu from ”Interlaced” to ”Progressive”.
DVD
To optical or coaxial
input of Dolby Digital/
DTS Decoder/
Amplifier/Receiver
To Component
connectors
To SCART connector
To power outlet
(AC 230V/50 Hz)
MODEL NO. DVD 22
SETUP AND CONNECTIONS 13
Page 14
Remote Control
Battery installation
Insert the batteries supplied while observing the
correct (+) and (–) polarities.
Service life of batteries
■ The batteries normally last for about one year,
although this depends on how often, and for
what operations, the remote control is used.
■ If the remote control unit fails to work even
when it is operated near the player, replace
the batteries.
■ Use size “AA” batteries.
Notes:
■ Do not attempt to recharge, short-circuit,
disassemble, heat or throw the batteries into
fire.
■ Do not drop, step on or otherwise impact the
remote control unit. This may damage the
parts or lead to malfunction.
■ Do not mix old and new batteries.
■ Wipe away any leakage inside the remote
control unit, and install new batteries.
■ If leakage should come into contact with
parts of your body, wash it off thoroughly
with water.
■ Batteries contain chemical substances and we
recommend that you dispose of them properly
and in compliance with any local regulations.
Do not simply throw them away but return to
your dealer or special battery disposal centers.
Remote control operation range
Point the remote control unit from no more than
about 7 m from the remote control sensor and
within about 60 degrees of the front of the unit.
DVD 22
DVD 22
■ The operating distance may vary according to
the brightness of the room.
Notes:
■ Do not point bright lights at the remote
control sensor.
■ Do not place objects between the remote
control unit and the remote control sensor.
■ Do not use this remote control unit while
simultaneously operating the remote control
unit of any other equipment.
14 REMOTE CONTROL
Page 15
Digital Audio Connections
Audio output from the unit’s
optical/coaxial digital audio
output connector
Disc:
Sound recording
format:
Dolby Digital
DVD
(AC-3)
Linear PCM
(48/96 kHz
16/20/24bit)
DTS
MPEG (2.0)
MPEG-1 or
VCD
CD-DA
Linear PCM
CD
* Digital Format must be selected as
“ORIGINAL“ or ”PCM” respectively in Menu
Optical/Coaxial digital
audio output
Dolby Digital bitstream
(2-5.1 ch) or PCM
(2 ch, 48 kHz/16bit)*
Linear PCM (2 ch)
(48/96 kHz
16/20/24bit)
DTS Bitstream or no
output *
MPEG bitstream (2ch)
or linear PCM
(2 ch, 48kHz)
Linear PCM*
Linear PCM (44.1 kHz
sampling)
For your reference:
■ Dolby Digital (AC-3) is a digital sound compression technique developed by the Dolby
Laboratories Licensing Corporation,
supporting 5.1-channel surround sound, as
well as stereo (2-channel) sound, this technique enables a large quantity of sound data
to be efficiently recorded on a disc.
■ Linear PCM is a signal recording format used
in CDs.While CDs are recorded in
44.1 kHz/16 bit, DVDs are recorded in
48 kHz/16 bit up to 96 kHz /24 bit.
■ If you have a Dolby Pro Logic Surround
decoder connected to the DVD’s analog
AUDIO OUT connectors, thanks to the
”Downmix” function of the DVD you will
obtain the full benefit of Pro Logic from the
same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from
titles encoded with Dolby Surround.
■ The DVD is designed to digitally output
96 kHz-PCM audio with a 96 kHz sampling
rate. However, some 96 kHz DVD's may
include copy protection codes that do not
permit digital output. For full 96 kHz fidelity
from these discs, use the analog outputs of
the DVD.
IMPORTANT: If your surround processor/D/A
converter does not support 96 kHz PCM audio,
you must use the DVD analog outputs for full
96 kHz fidelity with these discs.
Caution for the optical/coaxial
digital audio outputs:
■ When connecting an amplifier (with an
optical/coaxial digital input ) which does not
contain a Dolby Digital (AC-3) or DTS
decoder, be sure to select ”PCM” as initial
setting in the ”Digital Output” menu (see
also page 18).
Otherwise, any attempt to play a DVD may
cause such a high level of noise that it may
be harmful to your ears and damage your
speakers.
■ CD´s can be played as they would normally be
played.
Note:
■ Some first generation DTS decoders which do
not support DVD-DTS interface may not work
properly with the DVD/CD player.
Notes when connecting the
optical digital audio cable
(optional)
■ Remove the dust protection cap from the
optical digital audio output and connect the
cable firmly so that the configurations of both
the cable and the connector match.
■ Keep the dust protection cap and always
reattach the cap when not using the connector.
Dolby Digital and DTS
Both Dolby Digital and DTS are audio formats
used to record 5.1-channel audio signals onto
the digital track of film. Both of these formats
provide six separate channels: left, right, center,
left rear, right rear, and common subwoofer.
The latest 6.1-formats, Dolby Digital EX and DTS
ES, even one (or two) additional "Surround
Back" channel for a center between the rears.
Remember, that Dolby Digital or DTS will only
play 5.1-channel sound if you’ve connected the
optical or coaxial output of the DVD player to a
DTS or Dolby Digital receiver or decoder and if
the disc was recorded in the Dolby Digital or DTS
format.
Dolby Digital is a trademark of Dolby Laboratories
Licensing Corporation.
Manufactured under license from Dolby
Laboratories. ”Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Confidential Unpublished Works.1992-1997
Dolby Laboratories, Inc. All rights reserved.
DTS is a registered trademark of Digital Theater
Systems.
DIGITAL AUDIO CONNECTIONS 15
Page 16
Playback Basics
Basic Play
Preparation
1. Switch the TV ON and select its video input
connected to the DVD.
2. Press POWER to turn on the unit, the DVD
harman/kardon logo should appear now on
the screen. If that logo appears distorted on
the screen or without any color, change the
appropriate settings at the Video Setting
Submenu according to your TV set and to the
connection used between the DVD and your
TV.
3. When you see no video at all, not even the
harman/kardon logo, check the setting of the
video input used on your TV (most SCART
inputs on TVs can be configured in the TV´s
menu). When you don´t succeed, connect your
TV with different cables to the DVD, e.g. via
Composite (yellow jacks) or S-Video cables,
rather than per SCART to view the setup
menus until all appropriate ”Video menu”
settings are made properly.
4. Switch on your A/V system’s power, if the
player has been connected to such a system.
5. Press OPEN/CLOSE to open the disc tray.
6. Place a disc on the disc tray.
Hold the disc without touching either of its
surfaces, position it with the side you wish to
play facing down, align it with the guides, and
place it in its proper position.
■ 3" (8 cm) discs or 5" (12 cm) discs can be
used.
7. Press PLAY. The disc tray is automatically
closed and play begins.
■ When the disc tray is closed by pressing
OPEN/CLOSE, play will start automatically.
■ With most DVD’s, a Disc Menu appears on
the screen. Select specific menu item by using
ARROW buttons on the remote, then press
ENTER.
Disc Playback Features
Skipping tracks or titles/chapters
To move forward or backward through the tracks
on a CD or the titles or chapters on a DVD, press
SKIP on the front panel or PREVIOUS/NEXT on
the remote.
Fast Motion Playback/Fast Search
1. To move forward or backward through the
DVD or CD disc being played at fast speed,
press SEARCH on the remote. Once one of
these buttons is pressed, the fast search will
continue until PLAY is pressed.
There are four fast-play speeds. Each press of
the SEARCH Buttons will cycle to the next speed
in the following order: 2x, 4x, 16x, 100x,
indicated by a number of arrow indicators on the
right top of the screen.
2. Press PLAY at any time to resume normal
playback.
Note that there will be no audio playback during
fast-forward or -reverse play of DVD discs.This is
normal for DVD, as A/V receivers and surround
processors cannot process the digital audio
streams during fast-play modes; audio will be
heard during fast-play of conventional CD’s.
Freeze Frame and Frame Advance
(with DVD only)
1. Press PAUSE when a DVD is playing to freeze
the picture.
2. Each time you press one of the STEP (FWD or
REV) buttons, the picture advances one frame
in the selected direction.
3. Press PLAY to resume normal playback.
Slow Motion Playback (with DVD only)
1. When a DVD disc is in pause or freeze frame
mode, you may move slowly forward or backward through the program being played at
one of four speeds by pressing the Play
Buttons on the remote. Each press of the
buttons will move to the next speed, indicated
by a number of arrow indicators on the right
top of the screen.
2. Press PLAY to resume normal playback.
Note that there will be no audio playback during
slow-forward or -reverse play of DVD discs.This
is normal for DVD, as A/V receivers and surround
processors cannot process the digital audio
streams during slow modes. Slow play is not
available for CD.
Notes: Playback features may not be available
during the opening credits of a movie.This is
intended by the disc author and is not a failure
of the DVD.
Playback of a DVD with 96 kHz/24-bit audio
requires the use of circuitry normally used for
other features.Accordingly, Slow Play Reverse
and Step Advance features are not available
with these discs.
Depending on the structure of a VCD disc, the
functions Slow Reverse and Step Reverse may be
prohibited or have no function and Fast Playback
(Search) may not function.
16 PLAYBACK BASICS
Page 17
System Setup
System Defaults
The final step of the installation is to establish
the system’s defaults. It is helpful to take a few
minutes to familiarize yourself with these
settings, as they may require change before the
first use and later from time to time.
General Functionality of the OSD Menu
The complete setup and control of the DVD 22
takes place in an advanced user-guided On
Screen Display (OSD) menu system. The OSD can
be activated by pressing the OSD button on the
remote control. Pressing this button again deactivates the OSD.
The main menu consists of a PLAYER Menu and a
SET-UP Menu. The PLAYER Menu will show all
information and options available for the disc
currently playing. The SET-UP Menu will help you
configure all audio and video settings which are
normally only made once.
Each Main Menu contains Submenus.These submenus are shown as icons on the left side of the
menu. They can be highlighted by a white square
around the icon by moving the cursor with the
ARROW buttons. Icons can be activated by pressing ENTER as soon as an icon is highlighted.
When ENTER has been pressed, the color of the
icon will change to dark blue and you will see
that the Actual Settings of this submenu will
appear on the right side of the menu.
Although each Menu has various Submenus and
Settings, navigating through menus, submenus
and settings goes the same way.All submenus,
settings and options can be accessed with the
help of the ARROW (
buttons on the remote control.
To change a setting, simply move the cursor to
the setting you wish to change.This setting will
be highlighted in light blue, and a brief explanation will appear in the Upper Menu Line on the
bottom of your screen. Once the setting is highlighted, pressing the ENTER button on the remote
control will show the available options for this
setting on the Lower Menu Line on the bottom of
your screen. Move the ARROW
to the requested option for this setting. Press
ENTER to activate the new setting.
KLN M
) and ENTER
M/N
buttons
Set Up Menu
The first step in checking or changing the system
defaults is to access the Setup Menu. First, make
certain that the DVD is properly connected to a
video display, and that power is connected. For
this process, however, you do not need to load
any discs into the unit.
During STOP, PAUSE or PLAY mode, if you press
OSD on the remote, the Set Up Menu appears on
the screen.
This Main Menu and all menus in the following
section may look different, listing the settings
with different languages, depending on the settings made previously.With the factory default
setting all languages are set to ”English”, that´s
why with all menus the English version is shown
in the manual.
In the SET-UP Menu you will find submenus for
making or changing all settings and adjustments
for both Audio and Video handling of your DVD
22.
To access the SET-UP Menu, press the OSD button, and move the cursor to the right until SET-UP
is highlighted. Press ENTER to activate the SYSTEM Settings:
System Settings
(A) (C)
(B) (E) (D)
(A) Main Menu Line
(B) Submenus
(C) Actual Settings
(D) Upper Menu Line with Brief Explanation
(E) Lower Menu Line with Possible Options
Display Language: Sets the language in which
the OSD menus are shown on your screen.
Preferred Subtitle Language: Defines your
preferred subtitle language. Every time a disc will
be played that contains this subtitle language, it
will be shown automatically. If you do not find
your preferred language in the list of options, you
can select your preferred language by typing a
4-digit code found in the code list on page 20.
You can also set the preferred subtitle language
to OFF. In that case no subtitles will be shown.
Panel Time-Out: Sets the time-out interval for
the Front Panel Information Display. After the
selected time, the display will dim completely.
Status Bar Time-Out: Sets the time-out interval
for the Status Bar, after which the Status Bar will
disappear from the screen.
Parental Control: Defines a password used to
control viewing of restricted programs.The
default password is 8888. After pressing the
default password, either the parental control
setting can be chosen, or a new password.The
five standard US rating symbols are ”G”
(General, level 2), ”PG” (Parental Guidance, level
4), ”PG13” (Parental Guidance and 13 years old,
level 4), ”R” (Restricted, level 6) and ”NC 17”
(from 17 years old, level 7).The DVD will accommodate a total of eight rating steps, as set by the
DVD creators.These additional steps allow for
more critical control of program playback for all
audiences. Level 8:All DVDs can be played. Levels
7 to 2: DVDs for general audiences/ children can
be played. Level 1: DVDs for children can be
played; DVDs for adults/general audiences are
prohibited. Follow the explanations on the screen
to set a new password.
PBC Support: Activates PBC (Play Back Control)
Support for VCD discs.
Screen Save: Activates a Screen Saver to
prevent an image to “burn” into a video display
device. If you connect the DVD 22 to a LCD or
plasma screen or video projector, we recommend
you activate the screen saver at all times.
Show Angle Icon: Determines whether the
Angle Icon will appear on the screen when there
are different angles available on a DVD disc.
The System Setting Submenu contains the
following settings. Follow the explanations in the
Upper Menu Line on the bottom of your screen to
change the settings.
SYSTEM SETUP 17
Page 18
System Setup
Audio Settings
The Audio Setting Submenu contains the following settings. Follow the explanations in the
Upper Menu Line on the bottom of your screen
to change the settings.
Preferred Audio Language: Defines your
preferred audio language. Every time a disc is
played that contains this audio language, it will
be activated automatically. If you do not find
your preferred language in the list of options,
you can select your preferred language by typing
a 4-digit code found in the code list on page 20.
Digital Output: If your system includes 5.1
digital audio surround decoding (Dolby Digital
and/or DTS), select ORIGINAL as the digital output. In that case all audio signals will be output
with their original format. If your system only
includes stereo and/or Dolby Pro Logic, select
PCM. Then all audio signals will be output in
PCM format only (DTS will output no signal).
PCM Limit: The DVD 22 is compatible with
both 48 kHz and 96 kHz sampling, but some
early A/V receivers and surround processors are
not. If your A/V receiver or surround processor is
NOT capable of handling 96 kHz signals, select
the 48 kHz option. If your A/V receiver or
surround processor IS capable of handling
96 kHz signals, select the 96 kHz option to
achieve the greatest audio fidelity available. If
NONE is selected, the complete signal will be
passed through to your A/V Receiver or surround
processor.
Dynamic Range: This setting enables Dolby
Digital recordings to be played back with full
dialogue intelligibility while reducing peak levels.
This smooth level compression prevents abrupt
loud transitions from disturbing others without
reducing the impact of the digital source
perceptibly.
Video Settings
The Video Setting Submenu contains the
following settings. Follow the explanations in the
Upper Menu Line on the bottom of your screen
to change the settings.
Aspect Ratio: This step selects the TV aspect
ratio, conventional screen shape (4:3) or
widescreen (16:9), according to your TV.
TV Standard: Sets the output video format i.e.
NTSC, PAL or SECAM, of the DVD player. If you
have a multi standard TV, we recommend the
AUTO setting for optimal picture quality.
Scan Type: Sets the video output to Interlace or
Progressive. Before changing the setting to
Progressive, make sure that your video display is
capable of handling progressive scan signals.As
soon as you select progressive scan the scan
type, the Video Output will automatically change
to Component.
Video Output: Sets the video output type to
Scart or Component. Scart will be used for most
TV’s. Component will be used for most LCD,
Plasma and projectors.
Scart Output: Selects which kind of video output signals will be routed over the scart. RGB
will be used for most TV’s.
Video Mode: This setting affects only the
Component Video Outputs, and it controls how
the video signals are optimized for progressive
scan display. In most cases, the “automatic”
mode is your best choice, as it senses whether
the disc being played was originally recorded on
video or shot on film. However, in some cases
you may wish to compensate for errors in the
disc authoring that occur when the frame rate is
not properly maintained when films are converted to video.Three choices are available:
• Auto: This is the recommended setting, as it
lets the DVD 22 analyze the signals from the
DVD and adjust the output accordingly.
• Movie: Choose this option for optimal play-
back of material that was shot on film, even
though you are viewing it on video via a DVD.
• Video: Choose this option for optimal playback of material that was shot directly to
video, such as concerts and sports programming.
Video Adjustment
The Video Adjustment Submenu contains access
to the Test Screen. First adjust the video display
device (TV) with the help of the Test Screen.
After that the output settings of the player can
be fine-tuned with the Color, Contrast,
Brightness,Tint and Black Level settings. In order
to change the settings, move the cursor to the
“+“ or “-“ icon on the same line as the setting.
Once one of the icons is highlighted, pressing
ENTER will increase or decrease the value of the
setting, as will be shown in the bar behind the
setting. To exit the Video Adjustment Menu,
move the cursor to DONE, and press ENTER.
18 SYSTEM SETUP
Page 19
Test Screen
Test Screen
When you activate the Test Screen via the OSD
you can activate a still image to test all settings
and the video performance of your TV. With the
vertical color bars you can test the following:
■ proper color intensity setting on your TV,
■ the proper color of each bar, showing if the
proper video standard is turned on: the colors
should be (left to right): black, white, yellow,
cyan (turquoise), green, magenta (purple), red,
blue, black.
■ proper color transition, seen as sharp
separation of the bars, S-Video will be better
than Video, RGB best of all.
■ the performance of the color filter in your TV
(with ”Video” signals), bar edges should show
no vertical crawling dots. Here S-Video and
RGB formats usually give no problems.
With the grey scale and the black/white fields
below the color bars the brightness and contrast
of your screen can be adjusted optimally, see
chapter ”TV Picture Adjustment” below.
Color Bars
Grey Scale
100%
Black/White
fields
TV Picture Adjustment with
Test Screen
These adjustments may be done now, but you
can also make them after setup has been
finalized.
Brightness adjustment:
1. Turn down the color control on your TV until
the color bars are visible in black and white.
2. Adjust the contrast to the lowest level where
you still can see all bars within the grey scale
in the test picture separately and clearly.
3. Adjust the Brightness so that the bars in the
grey scale are all visible.The bar furtherst to
the left has to be as black as possible rather
than grey but the next aside must clearly be
differable.All the bars in the grey scale have to
be gradually and evenly changing from black
to whiter, going from left to right.
Contrast adjustment:
1. Adjust the contrast on your TV until you see a
bright white bar in the right low corner of the
screen and a deep dark black bar at the left.
The optimal contrast setting will depend from
your preference and the surrounding light in
the TV room.
2. If the brightness of the white bar will no more
increase while turning up the contrast or when
the borders of the white ”harman/kardon” text
letters on top will bloom (overlight) into the
black areas, what drasticly will decrease the
sharpness of the script, then the Contrast has
been turned up too much. Reduce the contrast
until these effects will disappear and the video
still looks realistic.
3. If you are watching TV with a usual surrounding daylight, adjust the Contrast so that a normal video picture has about the same looking
as the surroundings in your room. By that way
the eye is relazed when watching the TV picture.This contrast setting may be reduced
when the surrounding light is dimmed, usually
improving the sharpness of a video a lot
thereby.
4. The grey scale in the middle line needs to have
the same clear difference between each bar as
before the contrast adjustment. If not, go back
to the brightness adjustment and repeat step 3
and then the contrast adjustments, making
only minor adjustments each time for
optimisation.
Color adjustment.
1. When the Brightness and the Contrast are set
optimally, turn up the color control to the level
of your perference.Adjust to the level where
the colors look strong but still natural, not
overdone. If the color level is too high,
depending from the TV used some of the bars
will seem wider or the color intensity will not
increase while the control is turned up.Then
the color control must be reduced again. At the
end you should test the color intensity also
with a video, e.g. pictures of natural faces,
flowers, fruit and vegetables and other well
known natural articles of our life most usefull
for an optimal setting of the color intensity.
2. If your TV has a Tint option (with most
European TVs this is available or effective only
with NTSC signals, not with PAL), use the large
white bar below the Greyscale to tweak the
warmth of the picture. Every viewer has a
difference in preference as how the glow of
the picture should be. Some prefer a little
colder picture, some a warmer glow.The Tint
function on your TV and the white bar can be
used to control this.Adjust the Tint to the level
where you feel the white color has the tone
you prefer.
TEST SCREEN 19
Page 20
Player Menu
Using the Status Bar Menu
The on-screen Status Bar contains many playback
features.To see the Status Banner Menu, press
STATUS on the remote control while a disc is
playing. Use the ARROW buttons on the remote
to move through the different features in the
Status Bar. When a feature is highlighted, press
ENTER on the remote to select it and to change it
with the help of the options listed on the screen.
Press ENTER to activate the change.
Title: The number shown indicates the number of
the title that is currently playing.
Chapter: The number shown indicates the
number of the chapter that is currently playing on
a disc.
Time: This item displays the time in DVD mode.
Press the ARROW step by step to activate:
Title Elapsed,Title Remaining, Chapter Elapsed,
Chapter Remaining. Depending on the choice
made, the bar will show a graphic view on where
the disc is currently playing.
PLAYER Menu
Once all the settings have been made, you are
ready to enjoy your DVD 22. Once you have
inserted a disc into the drawer you can explore
the other Main Menu, that is the PLAYER Menu.
This menu hosts all playback and program features, as well as all disc information.As you will
see, the lay out of this menu is comparable with
the lay out of the SET-UP Menu. The functionality
is the same too.The Submenus are shown on the
left side of the screen, with INFO and PROGRAM
activated by default. As in the SET-UP Menu,
settings can be highlighted with the ARROW
buttons and selected with the ENTER button on
the remote control. Options for the settings are
shown in the Lower Menu Line on the bottom of
the screen.
Disc: Shows the name of the disc as it has been
given by the artist
Audio: Shows the audio track that is currently
playing. Options are shown on both Menu Lines
on the bottom of the screen.
Playlist: Sets the order in which the current disc
is played back.
Repeat: Sets the repeat mode.
Random: Activates Random Playback when pos-
sible.
Subtitle: Shows the subtitle of the disc currently
playing.
In the PLAYER Menu, the chapter, track or picture
currently playing will be marked with an arrow
symbol in front of the Chapter (DVD), Track (CD,
MP3, WMA) or Picture (JPEG). Chapters, tracks
and pictures can be selected from this list at any
time by moving the cursor to the requested
chapter or track and pressing ENTER to confirm.
The top part of this screen can be de-activated to
show the complete Track list on the screen. To
de-activate, move the cursor to the INFO
Submenu of the left side of the screen. Press
ENTER until the icon is highlighted in light blue
and the full Track list is visible on the screen. In
the same way the Disc list can be removed from
the screen by de-activating the PROGRAM
Submenu.
Information Displays
In DVD and MP3 mode, activating the DISC INFO
Submenu will show information about the player
and the disc currently playing. The first lines will
show Disc Name and Disc ID. Below you can
compare the Aspect Ratio, Video Standard and
Scan Type available on the disc with the actual
settings of your player.
In the lower part of the screen the Audio
Resolution and Audio Format are shown, and at
the bottom you will see a graphical presentation
of the Video Bit Rate and the Audio Bit Rate of
the disc currently playing.
Programmed Play
In STOP mode, the Disc List can be used to create
your own program list for both DVD, CD, MP3,
WMA or JPEG discs. Move the cursor to the right
of the menu, into the Disc List. Move the cursor
up or down to the first track you would like to
program and press ENTER. The cursor will move
to the options in the Lower Menu Line.You can
either add the selected track (or picture) to the
playlist or give it the number you would like it to
have in your playlist, or clear the track from the
list. Move the cursor down to the next track you
would like to program and continue until your
playlist is complete. Once completed, move the
cursor up to the Playlist setting. Select
Programmed order from the options and press
PLAY to start the playback.
If you have a disc that contains both MP3 files
and JPEG images, you can choose to run these
simultaneously, mixing the MP3 audio with your
own images.The time interval can be chosen in
the Picture Setting.
20 PLAYER MENU
Page 21
DVD Language Codes
The availability of specific languages for the main audio track or subtitles is dependent on the choices made by a disc’s producer. You should always
consult the disc’s jacket for information on languages for any disc. In the case of some languages, you may be required to enter a code from the list below to
access that language.
Language Code Language Code Language Code
Abkhazian 6566
Afar 6565
Afrikaans 6570
Albanian 8381
Ameharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Aymara 6588
Azerbaijani 6590
Bashkir 6665
Basque 6985
Bengali; Bangla 6678
Bhutani 6890
Bihari 6672
Bislama 6673
Breton 6682
Bulgarian 6671
Burmese 7789
Byelorussian 6669
Cambodian 7577
Catalan 6765
Chinese 9072
Corsican 6779
Croatian 7282
Czech 6783
Danish 6865
Dutch 7876
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079
Fiji 7074
Finnish 7073
French 7082
Frisian 7089
Galician 7176
Georgian 7565
German 6869
Greek 6976
Greenlandic 7576
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7387
Hindi 7273
Hungarian 7285
Icelandic 7383
Indonesian 7378
Interlingua 7365
Interlingue 7369
Iunpiak 7375
Irish 7165
Italian 7384
Japanese 7465
Javanese 7487
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kinyarwanda 8287
Kirghiz 7589
Kirundi 8278
Korean 7579
Kurdish 7585
Laothian 7679
Latin 7665
Latvian, Lettish 7686
Lingala 7678
Lithuanian 7684
Macedonian 7775
Malagsy 7771
Malay 7783
Malayalam 7776
Maltese 7784
Maori 7773
Marathi 7782
Moldavian 7779
Mongolian 7778
Naru 7865
Nepali 7869
Norwegian 7879
Occitan 7967
Oriya 7982
Oromo (Afan) 7977
Panjabi 8065
Pashto, Pushto 8083
Persian 7065
Polish 8076
Portuguese 8084
Quechua 8185
Rhaero-Romance 8277
Romanian 8279
Russian 8285
Samoan 8377
Sangho 8371
Sanskrit 8365
Scots Gaelic 7168
Serbian 8382
Servo-Groatian 8372
Sesotho 8384
Setswana 8478
Shona 8378
Sindhi 8368
Singhalese 8373
Siswati 8383
Slovak 8375
Slovenian 8376
Somali 8379
Spanish 6983
Sundanese 8385
Swahili 8387
Swedish 8386
Tagalog 8476
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga 8479
Tsonga 8483
Turkish 8482
Turkmen 8475
Twi 8487
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapuk 8679
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 7473
Yoruba 8979
Zulu 9085
DVD LANGUAGE CODES 21
Page 22
Technical Specifications
Applicable Disc: Disc formats: 5 inch (12 cm) or 3 inch (8 cm) DVD Video, Standard conforming DVD+RW, DVD+R, DVD-R and
DVD-RW,VCD, CD, CD-R, MP3, WMA, JPEG or CD-RW discs,
Regio code: DVD Video disc with Code 2 or 0 only.
DVD-Layers: Single Side/Single Layer, Single Side/Dual Layer, Dual Side/Single Layer, Dual Side/Dual Layer
Audio formats: Linear PCM, MPEG, MLP/CPPM, Dolby Digital or DTS
Video Signal System: PAL/NTSC
Composite Video Output: 1 V
S Video Output: Y/Luminance: 1 V
Component Video Output: Y: 1 Vp-p
Analog Audio Output: 2 Vrms max
Frequency Response: DVD (Linear PCM): 2 Hz - 22 kHz +0/-0.5 dB (48 kHz sampling)
Signal/Noise Ratio (SNR): 105 dB (A-weighted)
Dynamic Range: DVD: 100 dB (18 Bit)/105 dB (20 Bit)
THD/1kHz: DVD/CD: 0.003 %
Wow & Flutter: Below Measurable Limits
AC Power: 110 - 240 V/50 - 60 Hz
Power Consumption: 2 Watts (On) /20 Watts (Max)
Dimensions (WxHxD): 440 x 49 x 330 mm
Weight: 3.3 Kg
p-p/75 Ohms, sync negative polarity
p-p/75 Ohms, sync negative polarity
C/Chrominance: 0.286 V
p-p
/75 Ohms, sync negative polarity
p-p/75 Ohms
Cr: 0.7 V
Cb: 0.7 V
p-p/75 Ohms
2 Hz - 44 kHz +0/-0.5 dB (96 kHz sampling)
CD: 2 Hz - 20 kHz +0/-0.5 dB
CD/DVD: 96 dB (16 Bit)
Depth measurement includes knobs and connectors.
Height measurement includes feet and chassis.
All specifications subject to change without notice.
Harman Kardon and Power for the digital revolution are trademarks of Harman Kardon, Inc.
Manufactured under license from Dolby Laboratories. Dolby, AC-3, ProLogic and the double-D symbol are trademarks of
Dolby Laboratories. Confidential.
Unpublished Work. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
DTS is a trade mark of Digital Theater Systems, Inc.
Microsoft, Windows and WMA are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or diassembly is
prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER,
PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
22 TECHNICAL SPECIFICATIONS
Page 23
23
Page 24
250 Crossways Park Drive,Woodbury, New York 11797
www.harmankardon.com
Harman Consumer Group International:
2, Route de Tours, 72500 Château-du-Loir, France
© 2004 Harman Kardon, Incorporated
Partnumber: 312-AB220000-0000
Loading...