Harman Kardon DVD 16/230 Service Manual

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 1 of 39

harman/kardon Service Manual

DVD 16/230 DVD 18/230

DVD players

Only sold with AVR 139 and AVR 141 as AVR/DVD combos 13916, 13918, 14116, 14118..

ESD PRECAUTIONS 2 SERVICING PRECAUTIONS OWNER’S MANUAL FR OM TABLE OF CONTEN REMOTE CONTR AVR/DVD S FEATURES 12 FRONT PANEL CONTROLS REAR SETUP A

YSTEM CONNECTI

PANEL CONNECTIONS

ND CONNEC

ONT PAGE 5

TS 6

OL FUNCTIONS 7

TIONS 15

Released EU2010 Harman Consumer Group, Inc. Rev 0, 09/2010 8500 Balboa Boulevard. Northridge, California 91329

CONTENTS

ONS 11

13 14

TROUBLESHOOTING GUIDE 16 TECHNICAL SPECIFICATIONS 17 SOFTWARE CHECK + TROUBLESHOOTING CHARTS

XPLODED VIEW

E DVD 16 SERVICE PART DVD 18 SERVICE PART PCB

DRAW WIRING DIAGRAM SCHEMATI

INGS

C DIAGRAMS

UPGRADE 18

S 25 S 26

31 32-39

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 2 of 39

ESD PRECAUTIONS

Electrostatically Sensitive Devices (ESD)

Some semiconductor (solid state) devices can be damaged easily by static electricity . Such components commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir cuits and some field-effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity .

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur face such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly .

3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESD devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices.

6. Do not remove a replacement ESD device from its protective package until immediately before you are ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials).

7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the device will by installed.

CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL

OTHER SAFETY PRECAUTIONS.

8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gen erate static electricity sufficient to damage an ESD device).

SERVICING PRECAUTIONS

NOTES REGARDING HANDLING OF THE PICK-UP

1. Notes for transport and storage

1) The pick-up should always be left in its conductive bag until immediately prior to use.

2) The pick-up should never be subjected to external pressure or impact.

2. Repair notes

1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.

2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or damage to the printed-circuit board.

3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason the adjustment point and installation screws should absolutely never be touched.

4) Laser beams may damage the eyes! Absolutely never permit laser beams to enter the eyes! Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.

5) Cleaning the lens surface If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot ton swab should be used, taking care not to distort this.

6) Never attempt to disassemble the pick-up. Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab. (Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.

Storage in conductive bag

NEVER look directly at the laser beam, and don’t let contact fingers or other exposed skin.

Magnet

How to hold the pick-up

Conductive Sheet

Cotton swab

Pressure

Drop impact

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 3 of 39

NOTES REGARDING COMPACT DISC PLAYER REPAIRS

1. Preparations

1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These components are sensitive to, and easily af fected by, static electricity. If such static electricity is high voltage, components can be damaged, and for that reason components should be handled with care.

2) The pick-up is composed of many optical components and other high-precision components. Care must be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong

magnetism is present, or where there is excessive dust.

2. Notes for repair

1) Before replacing a component part, first disconnect the power supply lead wire from the unit

2) All equipment, measuring instruments and tools must be grounded.

3) The workbench should be covered with a conductive sheet and grounded. When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is because there is the possibility of damage by static electricity.)

4) To prevent AC leakage, the metal part of the soldering iron should be grounded.

5) Workers should be grounded by an armband (1M Ω)

6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent static electricity changes in the clothing to escape from the armband.

7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.

Resistor (1 Mohm)

Conductive Sheet

Resistor (1 Mohm)

Armband

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 4 of 39

Artwork number: 080-1437

ENGLISH

AVR/DVD System

AVR Audio/Video Receiver DVD Digital Versatile Disc Player

OWNER’S MANUAL

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 5

of 39

This owner's manual covers any combination of AVR 139, AVR 141, DVD 16 and DVD 18.

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 1 12/07/10 14:11:23

Artwork number: 080-1437

3 Safety Information 3 Unpacking 4 Remote Control Functions AVR 8 Front Panel Controls 10 Rear Panel Connections 12 Installation and Connections 12 Audio Equipment Connections 12 Video Equipment Connections 13 HDMI Connections 14 System Configuration 14 First Turn On 14 Settings to be Made With Each Input Used 14 Input Setup 14 Speaker Setup 15 Surround Setup 15 Configuring the Surround Off

(Stereo) Modes

15 Stereo-Direct (Bypass) Mode 16 Stereo Digital Mode 16 Delay Settings/LipSync 16 Night Mode Settings 16 Output Level Adjustment

18 Operation 18 Basic Operation 18 Turning the AVR On and Off 18 Using the Sleep Timer 18 Source Selection 18 Controls and Use of Headphones 18 Surround Mode Selection 19 Digital Audio Playback 20 Selecting a Digital Source 20 Digital Status 20 Surround Mode Types 21 Night Mode 21 Tape Recording 21 Output Level Trim Adjustment 21 6-Channel Direct Input 21 Display Brightness 22 Memory Backup 22 Tuner Operation 22 RDS Operation 24 Troubleshooting Guide 24 Processor Reset 25 Technical Specifications AVR

DVD 26 Terminology 27 Features, Packing List 28 Front Panel Controls 29 Rear Panel Connections 30 Setup and Connections 30 Digital Audio Connections 31 Playback Basics 31 Basic Play 31 Disc Playback Features 31 About DivX Movie Files 32 DVD Player Set-up 32 System Defaults 32 Set Up Menu 34 Player Menu 34 Using the On-Screen Status Display 35 CD Playback 36 MP3 and JPEG Playback 38 Troubleshooting Guide 39 Technical Specifications DVD

TABLE OF CONTENTS

Table of Contents

Typographical Conventions

To help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.

Example – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

ExamplE

– (OCR type) indicates a message that is visible on the front-panel information display

– (number in a square) indicates a specific front-panel control

– (number in a circle) indicates a rear-panel connection

– (number in an oval) indicates a button or indicator on the remote.

Instructions for users on removal and disposal of used batteries. Specification of included battery types.

These symbols shown on the product, the packaging or in the manual or separate information sheet mean that the product itself, as well as the batteries included or built into the product, should never be thrown away with general household waste. Take them to applicable collection points, where proper treatment, recycling and recovery takes place, in accordance with national or local legislation, or European Directives 2002/96/EC and 2006/66/EC.

Correct handling of the product and batteries to be disposed helps saving resources and prevents possible negative effects on the environment or human health.

The batteries included with your equipment may be Alkaline, Carbon Zink/ Manganese or Lithium (button cells) type. All types should be disposed of according to the above instructions.

To remove the batteries from your equipment or remote control, reverse the procedure described for inserting batteries in the Owners Manual.

For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. If, for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers.

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 6

of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 2 12/07/10 14:11:23

Artwork number: 080-1437

0 3 4

F H

































I J L

REMOTE CONTROL FUNCTIONS

Remote Control Functions for Receiver and DVD Player System

Power On Button

Not active

IR Transmitter Window

Power Off Button

Mute

Input Selectors

6-Channel Direct Input

Volume Up/Down

HD Mode Selector

Speaker Select/Setup

OK Button

Delay/Status Button

Memory/Angle Button

Clear Button

Preset Up/Down

RDS Select

Find Button

A-B

DTS Neo:6 Mode Selector

Stereo Mode Selector

Logic 7 Selector

Dim Button

Transport Buttons

Skip Up/Down Buttons (DWN)/(UP)

Night Mode

DTS Digital Mode Selector

Dolby Mode Selector

Repeat

Zoom Button

Tone Mode/Progressive Scan/Interlaced

Button

Tuning Up/Down

Direct Button

Tuner Mode Button

Numeric Keys

Digital Select/Audio Mode

Navigation Buttons

Channel Select /Disc Menu Button

V.OFF/Test Button

Surround Mode Selector/Subtitle Button

Sleep/Program Up/Audio Select Button

Title

AM/FM Tuner Select

AVR Selector

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 7 of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 4 12/07/10 14:11:25

Artwork number: 080-1437

ENGLISH

Remote Control Functions, common for AVR and DVD

REMOTE CONTROL FUNCTIONS

IMPORTANT NOTE: The combined AVR and DVD remote has some buttons that perform different functions. If you press the AVR Button

, one set of functions is active, identical to the functions for buttons CD, Tape, Video 1/2/3. If you press the DVD/ HDMI1 Button

, some of the buttons change their function as indicated above the button itself, and explained below. Refer to the function table for an overview of functions in both modes. NOTE that pressing the HDMI1 and DVD Buttons

activate the alternative commands as seen in the Function List on page 7.

Power On Button: Press this button to turn on the power to the AVR or the DVD selected by pressing either the AVR or the DVD/HDMI1 Button

This indicator is not active.

IR Transmitter Window: Point this window towards the AVR when pressing buttons on the remote to make certain that infrared commands are properly received.

Power Off Button: Press this button to place the AVR or a selected device unit in the Standby mode. If held for more than 3 seconds, both the AVR and the DVD switch to Standby.

Mute: Press this button to momentarily silence the AVR or TV set being controlled, depending on which device has been selected.

Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR. Finally, the DVD/HDMI1 Button will switch the double-function remote buttons to their DVD functions. After pressing the DVD/HDMI1 Button, you must press the AVR Selector button

again to operate all the AVR’s functions with the remote. Note that pressing the DVD Button switches on BOTH the AVR and the DVD, whereas pressing the AVR Button just switches on the AVR.

6-Channel Direct Input: Press this button to select the component connected to the 6-Channel Direct Input

as the audio. Note that when you wish to use the Six Channel Direct Input in conjunction with a video source, you must first select the video source by pressing one of the Input Selectors

. Then press this button to choose the 6-Channel Direct Input

as the audio source.

Volume Up/Down: Press these buttons to raise

or lower the system volume.

HD Mode Selector (DVD): When the DVD player is connected to a video display using the HDMI Output

, the display sends information to the DVD indicating the highest video resolution it is capable of handling, and the DVD automatically sets the video output to match it. Pressing this button allows you to manually change the output resolution, with your selection indicated by the Video Output Indicators

The HD-M button does allow you to force the DVD player to output video at a resolution that your TV does not support. If this happens, your TV screen may go blank or may display "Unsupported Format". If this occurs:

Wait 10 seconds.

Press the HD-M button, then the Left Navigation 2. button, then the OK button.

If the video does not recover, repeat steps 1 and 2 again.

Speaker Select/Setup: Press this button to begin the process of configuring the AVR’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the

buttons Z to select the

channel you wish to set up. Press the OK button

and then select the speaker type (see page 14 for more information.)

For DVD: Press this button to use the DVD’s on-screen menu system to adjust the player’s configuration settings. Note that the Info Button

must be pressed to access the DVD’s Information menu to obtain detailed disc information, and to configure the playback mode of the disc.

OK Button: This button is used to enter settings into the AVR’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

Delay/Status Button: Press this button to begin the process for setting delay times and lip sync delay. (See page 16 for more information).

For DVD: Press while a disc is playing to view banner display. Use the ARROW buttons to move through the different features in the Banner Display. When a symbol is highlighted, press OK on the remote to select it.

Memory/Angle Button: Press this button to enter a radio station into the AVR’s preset memory. Two underline indicators will flash at the right side of the Main Information Display

, you then have five seconds to enter a preset memory location using the Numeric Keys

. (See page 22 for more

information.)

For DVD: Press to access various camera angles on a DVD (If the DVD contains multiple camera angles) or to rotate JPEG images.

Clear Button: Press this button to clear incorrect entries when using the remote to directly enter a radio station’s frequency.

Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR’s memory. When CD or DVD is selected using the Input Selector button

, these buttons may function as Slow Fwd/Rev (DVD) or ”+10” (CD).

RDS Select/Info (DVD) Button: Press this button to display the various messages that are part of the RDS data system of the AVR’s tuner. (See page 22 for more information on RDS).

For DVD: Press for detailed informations on the disc playing (Video/Audio Bit rate, Movie aspect ratio and others), and for current player settings made. Note that the unit doesn’t react on any transport button as long as the info menu is displayed. Press again to remove information from screen.

Find (DVD): Press this button to search for a specific location on the disc.

A-B (DVD): Press to select section A-B and to play repeatedly.

DTS Neo:6 Mode Selector: Pressing this selector button cycles the AVR through the various DTS Neo:6 modes, which extract a five-channel surround field from two-channel program material (from PCM source or analog input signal). The first press selects the last DTS Neo:6 surround mode that was in use, and each subsequent press selects the next mode in the following order:

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 8

of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 5 12/07/10 14:11:25

Artwork number: 080-1437

REMOTE CONTROL FUNCTIONS

Remote Control Functions, common for AVR and DVD

Stereo Mode Selector: Press this button to select a stereo playback mode. When the button is pressed so that

DSp SURR OFF

appears in

the Main Information Display

, the AVR will operate in a bypass mode with true fully analog, two-channel left/right stereo mode with no surround processing or bass management as opposed to other modes where digital processing is used. When the button is pressed so that

SURROUND OFF

appears

in the Main Information Display

, you may enjoy a two-channel presentation of the sound along with the benefits of bass management. When the button is pressed so that

5 CH STEREO

appears, the stereo signal is routed to all five speakers, if installed.(See page 15 for more information on stereo playback modes).

Logic 7 Selector: Press this button to select one of the available Logic 7 surround modes. (See page 19 for the available Logic 7 options).

Dim Button: Press this button to activate the Dimmer function, which reduces the brightness of the front panel display, or turn it off entirely. The first press of the button shows the default state, which is full brightness by indicating

VFD FUll

in the

Main Information Display

. Press the button again within five seconds to reduce the brightness by 50%, as indicated by

VFD HalF

. Press the button again within five seconds and the main display will go completely dark. Note that this setting is temporary; the display will always return to full brightness when the AVR is turned on. In addition,both the Power Indicator

and the blue accent lighting inside the volume control will always remain at full brightness regardless of the setting. This is to remind you that the AVR is still turned on.

Transport Buttons: These buttons operate the

DVD player.

Skip Up/Down Buttons (DVD):

(DWN): Press to go to beginning of current track. Press again quickly to go to beginning of previous track. After pressing the PAUSE button, each press of this button will move the image in reverse frame by frame.

(UP): Press to go to beginning of next track. After pressing the PAUSE

button, each press of this button

will move the image forwards frame by frame.

Night Mode: Press this button to activate the Night mode. This mode is available only with Dolby Digital encoded digital sources, and it preserves dialog (center channel) intelligibilty at low volume levels (See page 16

for more information).

DTS Digital Mode Selector: When a DTS source is in use the AVR will select the appropriate mode automatically and no other mode will be available. Pressing this button will display the mode currently selected by the AVR´s decoder, depending on the surround material played and the speaker setting.

Dolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing.

Repeat (DVD): Each press of this button changes the playback mode to repeat a chapter or track or the entire disc. A repeat icon will appear in the upper right corner of the screen indicating the current repeat mode. If the Player Information Screen is active, the changes will be displayed on screen.

Zoom Button: When a DVD is playing, press this button to zoom the picture so that it is enlarged. There are 4 steps to the zoom function, each progressively larger. Press through each of the zoom stages to return to a normal picture.

Tone Mode/Progressive Scan/Interlaced Button: Pressing this button enables or disables the

Bass and Treble tone controls. When the button is pressed so that the words

TONE IN

appear in the

Main Information Display

, the settings of the Bass and Treble controls will affect the output signals. When the button is pressed so that the words

TONE OUT

appear in the Main Information

Display

, the output signal will be “flat,” without

any bass or treble alteration.

For DVD: Press this button to change the resolution of the Component Video Output between standard definition and progressive definition (PAL interlaced and PAL progressive; NTSC interlaced and NTSC progressive). The new setting will become effective after quitting the Setup menu.

Tuning Up/Down: When the tuner is in use, these buttons will tune up or down through the selected frequency band. If the Tuner Mode

button

has been pressed or the Band button 8 on the front panel was held pressed so that

aUTO

appears

in the Main Information Display

, pressing either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception. When the

maNUal

appears in the Main

Information Display

, pressing these buttons will tune stations in single-step increments. (See page 22 for more information).

Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys

to select a station (See page 22 for more information on the tuner).

Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning. When the button is pressed so

maNUal

appears in the Main Information Display

pressing the Tuning buttons

will move the frequency up or down in single-step increments. When the FM band is in use and

aUTO

appears in

the Main Information Display

, pressing this button will change to monaural reception making even week stations audible. (See page 22 for more information.)

Numeric Keys: These buttons serve as a ten- button numeric keypad to enter tuner preset positions. For DVD play you may enter track numbers directly, followed by OK to go to the track.

Digital Select/Audio Mode: Press this button to assign one of the digital inputs

4G9L to a

source. (See page 12 for more information on using digital inputs.) Audio Mode: When operating the DVD, press this button to switch between Audio Modes.

Navigation Buttons: These buttons are used to increase or decrease output levels when configuring the unit, to select speaker configuration or to select the digital inputs.

Channel Select /Disc Menu Button: This button is used to start the process of setting the AVR’s output levels with an external source. Once this button is pressed, use the

buttons Z to select the

channel being adjusted, then press the OK button

, followed by the KL buttons again, to change the level setting. (See page 21 for more information.)

DVD Disc Menu: Displays the actual DVD Disc Menu on the TV screen in play mode. When playing discs with JPEG images, pressing this button will access the thumbnails.

V.OFF/Test Button: Press to turn off video output for improved performance from audio-only discs. Press again to restore video output.

Tone: Press this button to begin the sequence used to calibrate the AVR’s output levels. (See page 16 for more information on calibrating the AVR).

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 9

of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 6 12/07/10 14:11:25

Artwork number: 080-1437

ENGLISH

Remote Control Functions, common for AVR and DVD

REMOTE CONTROL FUNCTIONS

Surround Mode Selector/Subtitle Button: Press this button repeatedly to select an available surround mode.

When a DVD is playing, press to select a subtitle language or to turn subtitles off.

Note: Due to the variations in how DVD discs are authored, the subtitle languages selected with the Subtitle Button may not accurately reflect the actual languages available on the disc. It is recommended that subtitles be selected using the disc’s menu.

Sleep/Program Up>/Audio Select Button: Press this button to place the unit in the Sleep mode. After the time shown in the display, the AVR will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:

Hold the button pressed for two seconds to turn off the Sleep mode setting.

Note that this button is also used to change channels on your TV, VCR and SAT receiver when selected.

DVD: Press to access various audio languages on a DVD (If the DVD contains multiple audio streams).

Title: When a disc is playing, press to make the DVD-player go back to the first section of the disc. If you are playing a DVD-Audio disc, pressing this button returns you to the Disc Menu with most DVD-A discs.

AM/FM Tuner Select: Press this button to select the AVR’s tuner as the listening choice. Pressing this button when the tuner is in use will select between the AM and FM bands.

AVR Selector: Pressing this button will switch the remote so that it will operate the AVR’s functions. If the AVR is in the Standby mode, it will also turn the AVR on.

Function List

Button Name

HK AVR Remote Command AVR/TAPE/CD/AUX/VID1/VID2/VID3/HDMI2/HDMI3

HK DVD Remote Command

DVD/HDMI1 Power ON Power On Power On Power OFF Power Off (press and release) Power Off (press and release)

Power Off (press and hold) Power Off (press and hold)

Mute Mute Mute(AVR) AVR AVR Power On AVR(AVR) DVD DVD DVD(AVR) VID1 VID 1 VID 1(AVR) HDMI1 HDMI 1 HDMI 1(AVR) AM/FM AM/FM AM/FM(AVR) CD CD CD(AVR) VID2 VID 2 VID 2(AVR) HDMI2 HDMI 2 HDMI 2(AVR) AUX AU X AUX(AVR) TAPE TAPE TAPE(AVR) VID3 VID 3 VID 3(AVR) HDMI3 HDMI 3 HDMI 3(AVR) SLEEP / AUDIO Sleep Audio TITLE Title 6CH 6CH 6CH(AVR) VOL Up Vol Up Vol Up(AVR) SURR. / SUBT. Surround Mode Subtitle TEST / V.OFF Test Tone Video Off HD-M HD Mode VOL Down Vol Down Vol Down(AVR) CH. / DISC MENU Channel Select Disc Menu SPKR / SETUP Speaker Select Setup Level+/Up Level+/Up Up Left

M Left Left

OK SET Enter Right

N Right Right

Level-/Down Level-/Down Down DIGITAL / AUDIO MODE Digital S elect Audio Mode DELAY / STATUS Delay Status 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 TUN-M Tuner Mode 9 9 9 0 0 0 MEM / ANGLE Memory Angle TUNING Up Tuning Up DIRECT Direct Tuning CLEAR Clear Clear PRESET Up Preset Up Slow Up TUNING Down Tuning Down TONE / P/I Tone Mode P/I RDS / INFO RDS Info PRESET Down Preset Down Slow Down ZOOM Zoom REPEAT Repeat Play A-B A-B Repeat Play FIND Search DOLBY SUR Dolby Surround Dolby Surround(AVR) DTS SUR DTS Surround DTS Surround(AVR) DTS NEO:6 DTS NEO:6 DTS NEO:6(AVR) NIGHT Night Mode Night(AVR) LOGIC 7 Logic7 Logic7(AVR) STEREO Stereo Stereo(AVR) SKIP DOWN Skip Down(DVD) Skip Down SKIP UP Skip Up(DVD) Skip Up DIM Dimmer Dimmer Rew(

) Rew(DVD) Rew

Play(

) Play(DVD) Play

FF(

) FF(DVD) FF Open/Close Open/Close(DVD) Open/Close Stop Stop(DVD) Stop Pause Pause(DVD) Pause

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 10 of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 7 12/07/10 14:11:25

Artwork number: 080-1437

ENGLISH

Rear Panel Connections

REAR PANEL CONNECTIONS

Video Monitor Output: Connect these jacks to the composite input of a TV monitor or video projector to view the output of any video source selected by the receiver’s video switcher.

HDMI Inputs: Connect the HDMI output of video sources such as a DVD player, set-top box or HDTV tuner to either of these jacks.

HDMI Output: Connect this jack to the HDMI input on a compatible HDMI-equipped video display.

Monitor Component Video Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the two Component Video Inputs

is selected the signal will be sent to these jacks.

Video 2 Component Video Inputs: Connect the Y/Pr/Pb component video outputs of a DVD player to these jacks.

Note: All component inputs/outputs can be used for RGB signals too, in the same way as described for the Y/Pr/Pb signals, then connected to the jacks with the corresponding color.

RGB connection is not possible if the source outputs a separate sync signal (see page 13).

AC Power Cord: Connect the AC plug to an

unswitched AC wall output.

DVD Video Inputs: Connect these jacks to the composite output jacks on a DVD player or other video source.

Video 1 Video Outputs: Connect these jacks to the RECORD/INPUT composite jack on a VCR.

Video 2 Audio Inputs: Connect these jacks to the

PLAY/OUT audio jacks on a VCR or other video source.

Video 2 Video Inputs: Connect these jacks to the

PLAY/OUT composite jacks on a second VCR or other

video source.

Optical Digital Inputs: Connect the optical digital output from a DVD player, HDTV receiver, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, a DTS signal or a standard PCM digital source.

Video 1 Video Inputs: Connect these jacks to the PLAY/OUT composite jacks on a TV or other video source.

6-Channel Direct Inputs: These jacks are used for connection to source devices such as DVD-Audio or SACD players with discrete analog outputs.

Digital Audio Output: Connect this jack to the matching digital input connector on a digital recorder.

PQS

Front/Center Speaker Outputs: Connect these outputs to the matching + or – terminals on your front/center speakers. When making speaker connections, always make certain to maintain correct polarity by connecting the red (+) terminals on the AVR to the red (+) terminals on the speaker and the black (–) terminals on the AVR to the black (–) terminals on the speakers. (See page 14 for more information on speaker polarity.)

Surround Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right surround speakers. When making speaker connections always make certain to maintain correct polarity by connecting the red (+) terminals on the AVR to the red (+) terminals on the speakers and the black (–) terminals on the AVR to the black (–) terminals on the speakers. See page 14 for more information on speaker polarity.

AVR/DVD System Connections

AVR/DVD System Connection Instructions:

Connect your system like this, using the HDMI cable and the digital audio cable included with the DVD player:

Connect the DVD player's HDMI output

to the

receiver's HDMI 1 input

. NOTE: Do not use any

other input for this connection.

Connect the DVD player's Digital Audio Out

to the receiver's Coaxial 2 digital audio input 9. NOTE: Do not use any other input for this connection.

Connect the receiver's HDMI Monitor Out

to your

TV's HDMI input connector.

IMPORTANT

: You MUST connect the DVD Player's Coaxial Digital Output to the AVR Receiver's Coaxial Digital Input 2 to hear Dolby Digital and DTS surround sound through your new AVR/DVD system.

AVR

To HDMI In

Digital Audio Cable (supplied with DVD player)

HDMI Cable

(supplied with

DVD player)

HDMI Cable (not supplied)

DVD Player

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 11 of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 11 12/07/10 14:11:27

Artwork number: 080-1437

ENGLISH

High quality video

High Definition Multimedia Interface (HDMI) for a • single wire, digital connection to your HD-Ready screen.

Advanced sophisticated 10-bit MPEG-2 video

• decoding circuits.

• ure PAL with NTSC disc due to true NTSC/PAL conversion.

Dual-layer compatibility for extended play DVD

• .

• layback of JPEG image files

High quality digital audio

B • y connecting a DTS or a Dolby Digital decoder, you can enjoy high quality 5.1 digital surround sound from DTS or Dolby Digital discs.

With linear PCM audio at 16-24 bits and

•

44-96 kHz (also on digital output, see table

• page

30), audio quality exceeding that of CD becomes possible.

Coaxial digital audio output.

•

Many convenient features

On-Screen Menu for disc information or player • information.

Subtitles may be displayed in one of numerous

• languages*.

The multi-angle function allows you to choose

• the viewing angle of scenes which were shot from a number of different angles (Limited to DVD’s recorded with multiple camera angles.)

Multiple options for dialog language and

• soundtrack selection (limited to DVD’s recorded with multiple dialog languages or soundtracks).

• step Zoom during play and pause.

Backlit, ergonomically designed remote control • .

* The number of languages recorded depends on the software.

Compatible with CD as well as DVD

The DVD player will play any conventional Audio CD or recordable (CD-R) or erasable CD (CD-RW), MP3 or any DVD/Video disc with the region code 0 or 2.

Disc formats supported by this player

The unit can play the following disc formats (8 cm and 12 cm size):

• VD DVD-R

• DVD-RW

• DVD+R

• DVD+RW

• CD

• CD-R

• W

NOTE: Due to differences in the format of certain discs, it is possible that some discs may include a mix of features that are not compatible with the DVD player. Similarly, although the DVD player is capable of a wide range of features, not all discs include every capability of the DVD system. For example, although the DVD player is compatible with multi-angle discs, that feature is only possible when the disc is specially encoded for multi pleangle play. In addition, the DVD player is capable of playing back both Dolby Digital and DTS soundtracks, but the number and types of tracks available will vary from disc to disc. To make cer tain that a specific feature or soundtrack option is available, please check the options noted on the disc jacket.

Playback capability for CD-R, CD-RW

■ , JPEG, MP3,

DivX, DVD-R, DVD+R, DVD-RW and DVD+RW discs may vary due to variations in the quality of the disc and the recorder used to create the disc.

The DVD player is compatible with most discs

■

recorded with files encoded using MP3 as well as JPEG still images. However, note that variations in the encoder or codec used and the bit rate of the encoding may affect the DVD player's ability to play back a specific disc. As a result, we cannot guarantee complete compatibility with all encoders and versions of the codecs. For best results, we recommend that MP3 files be encoded at bit rates ranging between 32kbps and 320kbps. JPEG files should contain no more than 5 megapixels, and the file size should be no larger than 5Mb.

The DVD player will NOT play the following:

DVD discs with a Region Code other than 2 •

DVD-ROM data discs

•

DVD-RAM discs

•

DVD-Audio discs

•

SACD discs

•

CD-I discs

•

CD-G discs

•

SVCD discs

•

Kodak Photo CD™ discs (Kodak Picture CD discs,

• available to consumers, may be viewed using the DVD).

Discs intended for use in video game consoles

•

Discs recorded in the “VR” mode or at any speed

• other than “SP”

High-definition optical discs such as WMVHD,

• HD-DVD and Blu-ray

Packing List

1 Harman Kardon DVD Player

1 Coaxial digital audio cable

1 HDMI cable

Features

FEATURES

NOTE: This player is designed and manufactured for compatibility with Region Management Information that is encoded on most DVD discs. This player is designed only for playback of discs with Region Code 2, or for discs that do not contain Region Code infor mation. If there is any other Region Code on a disc, that disc will not play on the DVD player.

CLASS 1

LASER PRODUCT

harman/kardon

DVD 16 and 18 /230V Service Manual

Page 12 of 39

0220CSK - HK AVR-DVD System OM, WORK R2 01.indd 27 12/07/10 14:11:30

+ 27 hidden pages