Harman Kardon AVS-340 Owners Manual

DIGITAL LOGIC 7

VID 1

DVD

FMAM

TAPE 6 8 CH

VID 2

VID 3

VID 4

PRO LOGIC

3 STEREO

HEADPHONE

DSP 5 7 CH. STEREO

SURR. OFF

AVR 340

Optical 4

Coaxial 4

Video 4

AVR 340

Power for the Digital Revolution

®



AUDIO/VIDEO RECEIVER

OWNER’S MANUAL

AVR 340 AUDIO/VIDEO RECEIVER

The

Bridge

ntroduction

3 I

mportant Safety Information

4 I 4 U 5 Front-Panel Controls

8 Rear-Panel Connections 11 Main Remote Control Functions 15 Zone II Remote Control Functions 16 Installation and Connections 19 System Configuration 19 Speaker Selection and Placement 21 System Setup

2 23 Surround Setup 26 Automated Speaker Setup Using EzSet/EQ 28 Manual Setup 28 Speaker Size 30 Speaker Crossover Settings 30 Delay Settings 31 Output Level Adjustment 34 Operation 34 Basic Operation 34 Source Selection 34 6-Channel/8-Channel Direct Input 34 Volume and Tone Control 35 Surround Mode Selection 36 Surround Mode Chart 38 Digital Audio Playback 40 Surround Mode Availability for Incoming Bitstreams 41 Tuner Operation 42 Recording 42 Using 42 Output Level Trim Adjustment 42 Dim Function 44 Advanced Features 46 Multiroom Operation 48 Programming the Main Remote 48 Programming Device Codes 48 Macro Programming 49 Programmed Device Functions 50 V 50 Channel Control Punch-Through 50 Transport Control Punch-Through 50 Resetting the Remote Memory 51 Function List 53 Setup Code Tables 63 Troubleshooting Guide 63 Processor Reset 64 Technical Specifications 64 Trademark Acknowledgements 65 Index 66 Appendix – Settings Worksheet

Please register your product on our Web site at www product’ choose to be notified about our new products and/or special promotions.

npacking

sing the On-Screen Display

nput Setup

udio Setup

olume Punch-Through

.harmankardon.com. Note: You’ll need the

you can

s serial number

At the same time

Typographical Conventions

In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.

EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack

EXAMPLE – (OCR type) indicates a message that is visible on-screen or on the front-panel

mation display

infor 1 – (number in a square) indicates a specific front-panel control ¡ – (number in a circle) indicates a rear

a – (number in an oval) indicates a button or indicator on the remote

– (letter in an oval) indicates a button on the Zone II remote

The appearance of the text or cursor for your receiver’s on-screen menus may vary slightly from the illustrations in this manual.

Whether the text appears in all uppercase or upper

performance and operation remain the same.

For Canadian model

This class B digital apparatus complies with Canadian

CES-003.

I For models having a power cord with a polarized plug:

AUTION: To prevent electric shock, match wide blade

C of plug to wide slot, fully insert.

Modèle pour les Canadien

et appareil numérique de la classe B est conforme

C à la norme NMB-003 du Canada.

ur les modèles dont la fiche est polarisee:

S ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

-panel connection

- and lowercase characters

2 TABLE OF CONTENTS

INTRODUCTION

The

Bridge

The

Bridge

Thank you for choosing Harman Kardon®! With the purchase of a Harman Kardon AVR 340, you are about to begin many years of listening enjoyment.

esigned to provide all the excitement and detail of

ovie soundtracks and

m tions, the AVR 340

very nuance of musical selec-

accomplishes its mission by harnessing advanced technologies usually found only in higher-priced receivers.

The AVR 340 has been engineered so that it is easy to take advantage of all the power of its digital technology. However, to obtain the maximum enjoyment from your new receiver, we urge you to read this manual. A few minutes spent learning the functions of the various controls will enable you to take advantage of all the power the AVR 340 is able to deliver.

If you have any questions about this product, its installation or its operation, please contact your retailer or custom installer. They are your best local sources of information.

Description and Features

The AVR 340 is versatile and multifeatured, incorporating a wide range of listening options. In addition to

Digital and DTS®decoding for digital sources,

Dolby a broad choice of Matrix surround-encoded or stereo surround modes are available for use with your CD, VCR, TV broadcasts and the AVR 340’s own FM/AM tuner. Along with Dolby Digital EX, Dolby Pro Logic®IIx, DTS Neo:6®, DTS 96/24®, Dolby 3 Stereo, and Hall and Theater modes, the AVR 340 offers Harman International’s exclusive Logic 7®processing in both

5.1 and 7.1 versions to create a wider, more enveloping field environment and more defined fly-overs and pans. Another exclusive is VMAx processing to create an open,

, which uses proprietary

spacious sound field even when only two front speakers are available. Dolby Virtual Speaker is also available to create an enveloping sound field when fewer than six speakers are

The latest Dolby Headphone modes provide a

used. much more open and realistic presentation for private headphones listening.

In addition to providing a wide range of listening

VR 340 is easy to configure so that it

the

options provides the best results with your speakers and specific listening-room environment. On-screen menus combine with the EzSet/EQ system to automate speaker configuration and overall setup, resulting in a perfectly balanced sound field presentation that accurately reproduces the artist’s intent.

In addition to the configuration settings, EzSet/EQ also includes room equalization so that the signals sent to each speaker are tailored to provide accurate sonic quality with your specific combination of speaker type room size and other factors that influence room

acoustics.With EzSet/EQ, your system is custom-configured in a few minutes with accuracy that previously required expensive and hard-to-use test equipment.

In tandem with EzSet/EQ, the AVR 340 includes a full set of manual configuration settings for those who wish to custom-trim their system even further. A Quadruple Crossover bass management system

akes it possible to enter different crossover settings

m for each speaker group.

For the ultimate in flexibility, the AVR 340 features connections for five video devices, all with both

omposite and S-video inputs.Two additional audio

and eight digital inputs make the

inputs are available

, AVR 340 capable of handling all the latest digital audio sources. For compatibility with the latest HDTV video sources and progressive scan DVD players, the AVR 340 also features assignable two-input, widebandwidth, low-crosstalk component video switching.

The front panel offers coax and optical digital inputs for direct connection to digital recorders.Two video recording outputs, a preamp-out and a color-coded eight-channel input make the AVR 340 virtually futureproof, with everything needed to accommodate tomorrow’s new formats right onboard.

Until now, Harman Kardon AVRs have been able to accommodate almost any source device equipped with line-level analog, optical digital or coaxial digital outputs, including most digital media players. With one simple connection between the AVR 340 and the optional Harman Kardon , you are able to listen to materials stored on your compatible iPod (not included). Your AVR’s system remote control has been preprogrammed with control codes that enable you to select tracks for playback and of your iPod’s functions, even from across the room. The Bridge will even let you charge your iP

VR 340’s multizone options and a standard

The Zone II remote control make it possible to listen to a separate source in a room while the main home theater uses a different source.With assignable rear surround channel amplifiers, you may create a basic remote listening zone without any additional equip-

or one-wire multiroom connectivity

ment. F AVR 340 is A-BUS/

READY

, requiring only a single Category 5/5e cable and an optional remote module to power remote speakers while controlling volume and enabling full control over the program source and compatible IR-controlled devices.The unit’s Multiroom outputs may also be used to feed an optional, external power amplifier and volume control.

s powerful seven-channel amplifier uses

VR 340’

The

traditional Harman Kardon high-current design tech-

navigate many

od.

the

nologies to meet the wide dynamic range of any program selection.

Harman Kardon invented the high-fidelity receiver more than fifty years ago.With

state-of-the-art circuitry and time-honored circuit designs, the AVR 340 is the perfect combina nology, a

ant, easy-to-use package.

tion of the latest in digital audio tech-

quiet yet powerful analog amplifier in an

ele-

■ A wide range of digital and matrix surround

modes, including Dolby®Digital, Dolby Digital EX

olby Pro Logic

eadphone, DTS

H DTS 96/24

Ix, Dolby Virtual Speaker, Dolby

and DTS Neo:6

DTS-ES

iscrete and Matrix,

■ Seven channels of high-current amplification

■

Harman Kardon’s exclusive Logic 7®processing

available with both 7.1 and 5.1 processing in a variety of modes, and two modes of VMAx

■ system with included micro-

phone automatically configures speakers, sets delay times and output levels, and performs room equalization for optimal sound presentation

■ Programmable remote for control of AVR and

seven additional source components

■ High-bandwidth, HDTV-compatible component

video switching with assignable inputs and cross-conversion from composite and S-video

■ Discrete front-panel coaxial and optical digital

inputs for easy connection to portable digital devices and video game consoles

■ Connects to Harman Kardon’s

(optional) for charging, of a compa

tible iP

playback and control

device (not inc

luded)

■ Input titling for all input sources (except tuner)

■ Extensive bass management options, includ-

ing four separate crossover groupings

■ On-screen menu and display system

with choice of blue or black background screen, available with component video

■ A/V Sync delay adjustable for each input delivers perfect lip sync with digital programs or video displays

■ Extensive multiroom options, including a standard Zone II remote, assignable surround back amplifier channels and A-BUS/ capability for listening to a separa

READY

te source in

a remote zone

*Compatible with all iPod models equipped with a dock connector, including third-generation Click Wheel models and newer. Not compatible with iPod shuffle™models.Although

iPod video and photo models are compatible, video files and images stored on the iPod may not be viewed.

INTRODUCTION 3

SAFETY INFORMATION

Important Safety Information

Verify Line Voltage Before Use

Your AVR 340 has been designed for use with

20-volt AC current. Connection to a line voltage

1 other than that for which it is intended can create a safety and fire hazard and may damage the unit.

f you have any questions about the voltage requirements

I for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or a staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

Antenna Grounding

CATV or

If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, electrodes and requirements of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (Cable TV) system installer’s attention to article 820-40 of the NEC that provides guidelines for proper grounding and, ticular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entr

connection to grounding

in par

y as possible.

Installation Location

■ To ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and

evel surface.When placing the unit on a shelf, be

ertain that the shelf and any mounting hardware

c can support the weight of the product.

■ Make certain that proper space is provided both

bove and below the unit for ventilation. If this

a product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required.

■ Do not place the unit directly on a carpeted surface.

■ Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.

■ Avoid moist or humid locations.

■ Do not obstruct the ventilation slots on the top of

the unit, or place objects directly over them.

■ Due to the weight of the AVR 340 and the heat generated by the amplifiers, there is the remote possibility that the rubber padding on the bottom of the unit’s feet may leave marks on certain wood or veneer materials. Use caution when placing the unit on soft woods or other materials that may be damaged by heat or heavy objects. Some surface finishes may be particularly sensitive to absorbing such marks due to a variety of factors beyond Harman Kardon’s control, including the nature of the finish, cleaning materials used, and normal heat and vibration caused by the use of the product, or other factors. We recommend that caution be exercised in choosing an installation loca tion for the component and in normal maintenance practices, as your warranty will not cover this type of damage to furniture.

Cleaning

When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, mild soapy water, then a fresh cloth with clean water. Wipe dr benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts.Avoid spraying insecticide near the unit.

Moving the Unit

Before moving the unit, be certain to disconnect any interconnection cords with other components, make certain that you disconnect the unit from the AC outlet.

Important Information for the User

This equipment has been tested and found to comply

wipe it with a soft cloth dampened with

y immediately with a dry cloth. NEVER use

and

with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules.The limits are designed to provide reasonable protection against harmful interfer-

nce in a residential installation. This equipment gener-

tes,

ses and can radiate radio-frequency energyand,

u if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that

armful interference will not occur in a particular instal-

h lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

ser is encouraged to try to correct the interference by

u one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment

and receiver.

■ Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

■ Consult the dealer or an experienced radio/TV

technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user equipment.

Unpacking

The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair

T wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable environment and discard those materials at a local recycling center

It is important that you remove the protective plastic film from the front-panel lens. Leaving the film in place will affect the performance of your remote control.

o minimize the size of the carton in storage

’s authority to operate the

you may

. Please respect the

4 SAFETY INFORMATION4 SAFETY INFORMATION

FRONT-PANEL CONTROLS

DIGITAL LOGIC 7

VID 1

DVD

FMAM

TAPE 6 8 CH

VID 2

VID 3

VID 4

PRO LOGIC

3 STEREO

EADPHONE

DSP 5 7 CH. STEREO

SURR. OFF



(

)

VR 340

ptical 4

Coaxial 4

ideo 4

FRONT-PANEL CONTROLS

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

1 Main Power Switch 2 Power Indicator 3 Standby/On Switch 4 Headphone Jack 5 Tone Mode 6 Speaker Selector 7 Surround Mode Group Selector 8 Surround Mode Selector 9 Tuning Selector

‹/›

)

Buttons

1 Main Power Switch: Press this button to apply power to the AVR 340. When the switch is pressed

the unit is in a Standby mode, as indicated by the

in,

Power Indicator 2. This button MUST be

amber pressed in to operate the unit. T

o turn the unit off and to prevent the use of the remote control, this switch should be pressed until it pops out from the front panel and the word “OFF” is seen at the top of the switch.

NOTE: This switch is normally left in the “ON” position.

2 Power Indicator: This LED lights amber when the unit is in the Standby mode to signal that the AVR is ready to be turned on. When the unit is in operation, the indicator is blue

3 Standby/On Switch: When the Main Power

Switch

VR 340; press it again to turn the unit off. The

Indicator

is “ON,” press this button to turn on the

turns blue when the unit is on.

ower

! Tuner Band Selector @ Set Button # Digital Input Selector $ Preset Station Selector % Delay Adjust Selector ^ Input Source Selector & Tuner Mode Selector * Optical 4 Digital Audio Input ( Coaxial 4 Digital Audio Input Ó Video 4 Video Input Jacks

4 Headphone Jack: This jack may be used to listen

to the AVR 340’s output through a pair of headphones. The speakers will automatically be tur headphone jack is in use.When configuring your system using EzSet/EQ,

the calibration microphone should be plugged into this jack using the supplied adaptor that converts the small mini-plug at the end of the microphone’s cord to a 1/4" plug.

5 Tone Mode: This button controls the tone mode settings, enabling adjustment of the bass and treble boost/cut. You may also use it to take the tone controls out of the signal path completely for response.The first press of the button displays a TONE IN message in the Lower Display Line ı and in the on-screen display.To take the controls out of the signal path,

press either of the

Buttons ) until the display reads TONE OUT.

To change the bass or treble settings, make sure that

TONEINappears in the Lo

‹

›

‹

or press either of the

›

Buttons ) until it does.

ned off when the

“flat”

‹

›

‹

›

wer Display Line

Ô Video 4 Audio Input Jacks  Channel Adjust Selector Ò Volume Control Ú Input Indicators Û Speaker/Channel Input Indicators Ù Upper Display Line ı Lower Display Line ˆ Surround Mode Indicators ˜ Remote Sensor Window

Press the Tone Mode Button 5 until the desired option of

TREBLE MODE or BASS MODE

appears in the Lo

wer Display Line

on-screen display and then press either of the Buttons ) to enter the desired boost or cut setting. Both treble and bass contours may be boosted or cut by up to + or –10dB in increments of 2dB. See pages 23 and 34 for more information on the tone controls

NOTE:The

Balance control. When listening to two-channel materials, if you wish to adjust the stereo image, you may use the

VR 340 is not equipped with a traditional

Channel Adjust Selector  to increase or

decrease the level of the left front channel by up to + or –10dB, and then to decrease or increase the right front channel by the corresponding amount. However, when listening to surround materials and most twochannel materials, it is recommended that you leave these settings at the results obtained during the config uration process described on pages 19 through 33.

ı and in the

‹

›

FRONT-PANEL CONTROLS 55

The

Bridge

FRONT-PANEL CONTROLS

peaker Selector:Press this button to begin

6 S

the process of configuring the unit to match the type of speakers used in your listening room. (See pages 28–30 for more information on speaker setup and

onfiguration.)

7 Surround Mode Group Selector: Press this but- ton to select the top-level group of surround modes.

ach press of the button will select the current or last

E used mode in each of the surround mode groups (e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo). When the button is pressed so that the name of the

urround mode group appears in the on-screen dis-

s play and in the

Lower Display Line ı, press the

Surround Mode Selector 8 to cycle through the

individual modes available. For example, press this button to select Dolby modes, and then press the Surround Mode Selector 8 to choose from the various Dolby mode options.

8 Surround Mode Selector: Press this button to select from among the available surround mode options for the mode group selected. The specific modes will vary based on the number of speakers available, the mode group and if the input source is digital or analog. For example, press the

Mode Group Selector

7 to select a main mode

Surround

grouping such as Dolby or Logic 7, and then press this button to see the specific mode choices available. Note that the digital surround modes, such as Dolby Digital and DTS, may not be accessed unless that type of source signal is present, such as when a DVD movie or television signal programmed in Dolby Digital or DTS surround sound is playing. For more information on surround mode selection,

see pages 25 and 35–41.

9 Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When the tuner is in the Manual mode, decrease the frequency by one increment.

each tap will increase or

When the tuner receives a strong enough signal for adequate reception, on-screen display and the

MANUAL TUNED will appear in the

Lower Display Line ı.

When the tuner is the Auto mode, press the button once, and the tuner will scan for a station with acceptable signal strength.

When the next station with a strong signal is tuned the scan will stop and the on-screen display and will indicate AUTO

wer Display Line

TUNED.When an FM

Stereo station is tuned, the display will read AUTO ST TUNED.

To switch back and forth between the Auto and Manual tuning modes, press the

Selector

Tuner Mode

) ‹/› B

uttons:When configuring the AVR 340’s

settings, use these buttons to select from all of the available choices

! Tuner Band Selector: Press this button to turn the AVR on and to select the Tuner as the input. Press it again to switch between the AM and FM frequency bands. (See page 41 for more information on the tuner.)

@ Set Button: When making choices during the setup and configuration process, press this button

o enter the desired setting into the AVR 340’s memory.

# Digital Input Selector: Press this button to select one of the digital audio inputs or the analog audio input for any source. (See pages 38–41 for more information on digital audio.)

$ Preset Stations Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 41 for more information on tuner presets.)

% Delay

Adjust Selector:

Press this button to begin the steps required to enter delay settings. (See pages 30–31 for more information on delay times.)

^ Input Source Selector: Press this button to change the input by scrolling up or down through the list of

Input Indicators Ú.

& Tuner Mode Selector: Press this button to select

Auto or Manual tuning. When the button is pressed so that the

AUTO appears in the Lower Display Line

ı, the tuner will search for the next station with an acceptable signal when the

is pressed.

When the button is pressed so that

MANUAL appears in the Lo each press of the

Tuning Selector 9u

wer Display Line

Tuning Selector 9u˚will

ı,

increase the frequency.This button may also be used to switch between Stereo and Mono modes for FM radio reception. When weak reception is encountered, the button so that

Display Line

MANUAL appears in the Lo

ı and on the on-screen display to

press

wer

switch to Mono reception. Press it again to switch back to Stereo mode

(See page 41 for more infor

mation on

using the tuner.)

* Optical 4 Digital Audio Input: Connect the optical digital audio output of an audio or video product to this jack. When the input is not in use, the built-in shutter will close to avoid dust contamination that might degrade future perfor

mance.

( Coaxial 4 Digital Audio Input: This jack is used for connection to the output of portable audio devices, video game consoles or other products that have a coax digital audio jack.

ideo 4 Video Input Jacks:These jacks may

Ó V

be used for temporary connection to the composite or S-video output of video games, camcorders or other portable video products.You may make a connection

o either jack at any time, but not to both simultaneously.

Ô Video 4 Audio Input Jacks: These audio jacks may be used for temporary connection to video

ames or portable audio/video products such as

g camcorders and portable audio players.

NOTE: The AVR 340 is shipped with two covers that may be installed over the front-panel input jacks when they are not in use.

 Channel Adjust Selector: Press this button to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment,

see page 31.)

Ò Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR 340 is muted, adjusting the

Volume Control Òb©will automatically

release the unit from the silenced condition.

Ú Input Indicators: The current selected source will appear as one of these indicators.When the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.

NOTE: When /DMP has been selected as the input source, no

Input Indicator N will light.

DMP/THE BRIDGE IS CONNECTED

will scroll across the Upper Display Line P, unless you have retitled the source name, in which case that name will appear. See page 22 for more information on input titling.

Û Speaker/Channel Input Indicators: These indi- cators are multipurpose, indicating both the speaker type selected for each channel and the incoming datasignal configuration. The left, center, right, side surround and back surround speaker indicators are composed of three boxes, while the subwoofer is a single box. The center box lights when a “small” speaker is selected, and the two outer boxes light when

“large” speakers are selected. When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been assigned that position. (See pages 28–29 for more

mation on configuring speakers.)

infor

NOTE: When you have reassigned the surround back speakers to the remote zone using the

ROOM SETUP

menu, the boxes that indicate the

MULTI

presence of the surround back speakers will automati cally disappear, reflecting the fact that the main listening area is now configured for 5.1-channel operation.

6 FRONT-PANEL CONTROLS

(See page 46 for more information on reassigning the surround back speakers for multiroom use.)

he letters inside each box display the active input

T channels. For standard analog sources, only the L and R will light, indicating a stereo input. For a digital source, the indicators will light to display the channels being

eceived at the digital input. When the letters flash, the

r digital input has been interrupted. (See page 39 for more information on the Channel Indicators.)

pper Display Line:Depending on the unit’s sta-

Ù U

tus, a variety of messages will appear here. In normal operation, this line will show current input source and which analog or digital input is in use.When the tuner is the input, this line will identify the station as AM or FM and show the frequency and preset number, if any.

ı Lower Display Line: Depending on the unit’s sta- tus, a variety of messages will appear here. In normal operation, the current surround mode will show here.

ˆ Surround Mode Indicators: The current selected surround mode will appear as one of these indicators. Note that when the unit is turned on, the entire list of available modes will light briefly, and then revert to normal operation with only the active mode indicator illuminated.

FRONT-PANEL CONTROLS

NOTE: When the Dolby Virtual Speaker mode is in

Surround Mode Indicator R will light.

use, no However, the surround mode name will scroll in the Lower Display Line Q.

˜ Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it.

FRONT-PANEL CONTROLS 77

YXW

ONM

2 3

4 5

DE F

The Bridge

The

Bridge

REAR-PANEL CONNECTIONS

NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

¡ FM Antenna Jack ™ Multiroom Audio Outputs £ CD Audio Inputs ¢ A-BUS®Connector ∞ Multiroom IR Input

§ Remote IR Carrier Output ¶ Preamp Outputs

• Subwoofer Output ª Remote IR Input ‚ Remote IR Output ⁄ Front Speaker Outputs ¤ Surround Back/Multiroom Speaker Outputs ‹ Surround Speaker Outputs › Center Speaker Outputs ﬁ Optical Digital Audio Inputs

o assist in making the correct connections

NOTE: T for multichannel input, output and speaker connections, all connection jacks and terminals are colorcoded in conformance with the CEA standards as follows:

Front Left: White

ront Right:

Red

¡ FM Antenna Jack: Connect the supplied indoor (or an optional external) FM antenna to this ter

™ Multiroom

Audio Outputs:

Connect these jacks

minal.

to the optional external audio power amplifier that is used for multizone distribution.

ﬂ Component Video Monitor Outputs ‡ Component Video 1 Inputs ° Component Video 2 Inputs

· Fan Vents a AC Power Cord b Switched AC Accessory Outlet c Unswitched AC Accessory Outlet d Optical Digital Audio Output e Coaxial Digital Audio Output f Coaxial Digital Audio Inputs g S-Video Monitor Output h DVD S-Video Input i Video 1 S-Video Input j DMP Connector k Video 1 S-Video Output

Center:

Green Surround Left: Blue Surround Right: Gray Surround Back Left: Brown

Surround Back Right: Subwoofer: Purple

Coaxial Digital Audio: Orange

£ CD Audio Inputs: Connect these jacks to the analog audio outputs of a compact disc player or CD changer

¢ A-BUS®Connector: Connect this jack to an optional A-BUS remote room product to extend the

U Video 2 S-Video Input V Video 2 S-Video Output W Video 3 S-Video Input X 6/8-Channel Direct Inputs Y Video Monitor Output Z DVD Audio/Video Inputs a Video 1 Audio/Video Inputs b Video 1 Audio/Video Outputs c Video 2 Audio/Video Inputs d Video 2 Audio/Video Outputs e Video 3

Audio/Video Inputs

f Tape Inputs g Tape Outputs h AM Antenna Terminals

Composite

Video:

ellow

Y Component Video “Y”: Green Component Video “Pr”: Red Component Video “Pb”: Blue

multiroom capabilities of your

AVR 340. See page 17

for more information on A-BUS.

∞ Multiroom IR Input: Connect the output of an IR sensor in a remote room to this jack to control the AVR 340’s multiroom system and source devices from

8 REAR-PANEL CONNECTIONS

REAR-PANEL CONNECTIONS

the remote room. See page 46 for more information on multiroom operation.

§ Remote IR Carrier Output: The output of this jack is the full signal received at the

Window

S, or input through the Remote IR Input

ª, including the carrier frequency that is stripped from these signals at the

his output to extend IR remote signals to the inputs of

t compatible products that require the full IR signal by direct connection to the product’s remote IR input, or through the use of optional, external IR “blasters”. If you are in doubt as to which of the two IR Output jacks to use, we recommend that you consult with your dealer or installer, or check with the manufacturer of the external equipment you wish to control.

¶ Preamp Outputs: Connect these jacks to an optional, external power amplifier for applications where higher power is desired.

• Subwoofer Output: Connect this jack to the line- level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input.

ª Remote IR Input: If the AVR 340’s front-panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.

‚ Remote IR Output: This connection permits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon (or other compatible) equipment.

⁄ Front Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right speakers. make certain to maintain correct polarity by connecting the color-coded (white for front left and red for front right) (+) terminals on the AVR 340 to the red (+) ter on the AVR 340 to the black (–) terminals on the speakers. See page 16 for more information on speaker polarity.

¤ Surround Back/Multiroom Speaker Outputs:

These speaker terminals are normally used to power the surround back speakers in a 7.1-channel system. However, they may also be used to power the speakers in a second zone, which will receive the output selected for a multiroom system. fed to these terminals from the default of the Surround Back speakers to the Multiroom Output, change a setting in the

SETUP

for more information on configuring this speaker output. black terminals are the surround back left channel positive (+) and negative (–) connections and the tan

When making speaker connections always

minals on the speakers and the black (–) terminals

menu of the OSD system. See page 46

mal surround system use

In nor

Remote IR Output ‚. Use

MULTI ROOM

Remote Sensor

o change the output

you must

the brown and

and black terminals are the surround back right positive (+) and negative (–) terminals. For multiroom use, connect the brown and black SBL terminals to the

ed and black connections on the left remote zone

peaker and connect the tan and black SBR terminals

s to the red and black terminals on the right remote zone speaker.

‹ Surround Speaker Outputs: Connect these out- puts to the matching + and – terminals on your surround channel speakers. In conformance with the CEA color-code specification, the blue terminal is the positive, or “+,” terminal that should be connected to the red (+) terminal on the Surround Left speaker, while the gray ter terminal on the Surround Right speaker. Connect the black (–) terminal on the AVR to the matching black negative (–) terminals for each surround speaker. (See page 16 for more information on speaker polarity.)

› Center Speaker Outputs: Connect these outputs to the matching + and – terminals on your center channel speaker. In conformance with the CEA color-code specification, the green terminal is the positive, or “+,” terminal that should be connected to the red (+) terminal on speakers with the older colorcoding. Connect the black (–) terminal on the AVR to the black (–) terminal on your speaker. (See page 16 for more information on speaker polarity.)

ﬁ Optical Digital Audio Inputs: Connect the optical digital output from a DVD player, HDTV receiver, LD player or CD Dolby Digital signal, a DTS signal or a standard PCM digital source.

ﬂ Component Video Monitor Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the selected, the signal will be sent to these jacks.

‡ Component

Y/Pr/Pb component video outputs of a DVD player, HDTV set-top converter, satellite receiver or other video source device with component video outputs to these jacks.

° Component Video 2 Inputs: Connect the Y/Pr/Pb component video outputs of a DVD player, HDTV set-top converter, satellite receiver or other video source device with component video outputs to these jacks.

See page 22 for information on assigning the Component Video 1 and 2 Inputs ‡° to the appropriate source inputs.

· F

of the AVR 340’s airflow system. To ensure proper operation of the unit and to avoid possible damage to

minal should be connected to the red (+)

player to these jacks.The signal may be a

Component Video Inputs ‡° is

Video 1 Inputs:

ents:

These ventilation holes are the output

Connect the

delicate surfaces behind the AVR, make certain that these holes are not blocked and that there is at least 3 inches of open space between the vent holes and

ny other surface. It is normal for the fan to remain off

t most normal volume levels. An automatic tempera-

a ture sensor turns the fan on only when it is needed.

a AC Power Cord: Connect the AC power cord to

non-switched AC wall outlet.

b Switched AC Accessory Outlet: These outlets may be used to power any device you wish to have

urned on when the AVR 340 is turned on.

c Unswitched AC Accessory Outlet: This outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR 340 is on or off.

NOTE: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts.

d Optical Digital Audio Output: Connect this jack to the optical digital input connector on a CD-R/RW, MiniDisc or other digital recorder.

e Coaxial Digital Audio Output: Connect this jack to the coaxial digital input of a CD-R/RW, MiniDisc or other digital recorder.

f Coaxial Digital Audio Inputs: Connect the coax digital output from a DVD player, HDTV receiver, player

or CD player to these jacks.The signal may be a Dolby Digital signal, DTS signal or a standard PCM digital source. Do not connect the RF digital output of an LD player to these jacks.

g S-Video Monitor Output: If any of the input sources used in your system have S-video connec tions to the AVR, connect this jack to the S-video input on your television,

NOTE: Thanks to the AVR 340’s cross-conversion capability, if your video display device is equipped with component (Y/Pb/Pr) video inputs, you need only to connect the to your display device, and the AVR 340 will automatically convert all composite and S-video source signals to the component video for also be able to view the AVR 340’s on-screen displays using just the component video connection, source device is a high-definition (720p, 1080i or 1080p) video device, in which case you would then need to either switch to a 480p source or connect the

Video Monitor Output Y or the S-Video Monitor

P to your video display in order to view the

Output

on-screen displays. h DVD S-Video Input: Connect the S-video output of

a DVD player or other video source to this jack.

projector or other video display

Component

Video Monitor Outputs

mat for display

You will

unless the

ﬂ

REAR-PANEL CONNECTIONS

REAR-PANEL CONNECTIONSREAR-PANEL CONNECTIONS

The

Bridge

The

Bridge

ideo 1 S-Video Input:If the product connected to

i V

the

Video 1 Audio Inputs a has S-video capability,

connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that the

onitor Output

s connected as described above.

g i

S-Video

j Digital Media Player (DMP) Connector:

With the AVR 340 turned off, connect the optional

arman Kardon to this connector

H Digital Media Player source is selected,

When the

you may view iPod control and navigation messages on your video display (if one is connected to one of the

onitor Outputs

isplay Lines PQ

, and in the Upperand Lower

gY)

ou may navigate the iPod

. Y

and select tracks for playback using the

Video

⁄

/¤/‹/

›

Buttons no, the Set Button p and Transport Controls ` on your AVR remote. See page 42 for

more information.

k Video 1 S-Video Output: If the product connected

Video 1 Audio Outputs Y has S-video capa-

to the bility, connect this jack to the REC/IN S-video jack on that unit.

U Video 2 S-Video Input:If the product connected to the

Video 2 Audio Inputs c has S-video capabil-

ity, connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that the

Monitor Output

g is connected as described above.

S-Video

V Video 2 S-Video Output: If the product connected to the

Video 2 Audio Outputs d has S-video capa-

bility, connect this jack to the REC/IN S-video jack on that unit.

W Video 3 S-Video Input: If the product connected to the

Video 3 Audio Inputs e has S-video capability,

connect this jack to the PLA that unit and then make certain that the

Monitor Output

g is connected as described above.

Y/OUT S-video jack on

S-Video

X 6/8-Channel Direct Inputs: These jacks are used for connection to source devices such as DVD-Audio or SACD

™

players with discrete analog outputs. Depending on the source device in use, all eight jacks may be used, though in many cases only connections to the front left/right, center, surround left/right and LFE (subwoofer input) jacks will be used for standard 5.1 audio signals.

Y Video Monitor Output: Connect this jack to the composite video input of a TV monitor or video projector to view the on-screen menus and the output of a standard video source.

NOTE: Thanks to the AVR 340’s cross-conversion capability, if your video display device is equipped with component (Y/Pb/Pr) video inputs, you need only to

onnect the

o your display device, and the AVR 340 will convert

omponent Video Monitor Outputs

ﬂ

all composite and S-video source signals to component video.You will also be able to view the AVR 340’s

on-

screen displays using the component video connec-

ion, unless the source device is high-definition (720p

t or 1080i) video, in which case you should either switch to a 480p source or connect the

Video or the

S-Video Monitor Output PY to your video display

o view the on-screen displays.

t Z DVD Audio/Video Inputs: Connect the composite

video and L/R analog audio outputs of a DVD player or other video source to these jacks.

a Video 1 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of a VCR or other video source to these jacks.

b Video 1 Audio/Video Outputs: Connect the composite video and L/R analog audio REC/IN jacks of a VCR or other video recording device such as a DVD recorder or PVR to these jacks.

c Video 2 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of a cable television box or other video source to these jacks.

d Video 2 Audio/Video Outputs: Connect the composite video and L/R analog audio REC/IN jacks of a VCR or other video recording device such as a DVD recorder or PVR to these jacks.

e Video 3 Audio/Video Inputs: Connect the com- posite video and L/R analog audio PLAY/OUT jacks of

tuner or other video source to these jacks

an HDTV

f Tape Inputs:

Connect these jacks to the PLAY/OUT

jacks of an audio recorder.

pe Outputs:

RECORD/INPUT

Connect these jacks to the

jacks of an audio recorder.

h AM Antenna Terminals: Connect the AM loop antenna supplied with the receiver to these terminals. If an external AM antenna is used, make connections

AM and GND terminals

to the

instructions supplied

the

in accordance with

antenna.

the

with

NOTE ON VIDEO CONNECTIONS: When connecting a video source product such as a VCR, DVD player, satellite receiver, cable set-top box, personal video

ecorder or video game to the AVR 340, you may

se either a composite or S-video connection, but

u not both, for each source device.

The AVR 340 features cross-conversion capability,

nabling you to benefit from higher-quality viewing of

e your video sources, even those that use composite or S-video switching, when connected to your video display with component video inputs.

10 REAR-PANEL CONNECTIONS

The

Bridge

POWER

MUTE

AM/FM

TAPE

VID 2

VCR

CBL/SAT

/8 CH

DMP

ID 1

VID 3

VID4

The Bridge

OFF

SLEEP

T/V

SURR.

CH.

OL.

SET

TUN-M

MEM

D.SKIP

DIRECT

OSD

TUNING

DOLBY SUR

DTS SURR

DTS NEO:6

STEREO

LOGIC 7

SKIP

DWN

PRESET

CLEAR

EST

NIGHT M-ROOM

DIM

ower Off Button

a P b IR Transmitter Window c Program Indicator d Power On Button

nput Selectors

e I

VR Selector

f A g AM/FM Tuner Select h Dim Button i Test Button

leep Button

j S k DSP Surround Mode Selector l Night Mode m Channel Select Button n

⁄/¤

‹/›

p Set Button q Digital Select

Buttons

r Numeric Keys s Tuner Mode t Direct Button u Tuning Up/Down v OSD Button w Dolby Mode Selector x DTS Digital Mode Selector y Logic 7 Mode Select Button z Skip Up/Down Buttons ` Transport Controls

R Stereo Mode Select Button S DTS Neo:6 Mode Select T

Macro Buttons

Disc Skip Button

Preset Up/Down

Clear Button

Memory Button

Delay/Prev. Ch.

Speaker Select

Multiroom Button

Volume Up/Down

TV/Video Selector

DMP Selector

6-Channel/8-Channel Direct Input

Mute

NOTES:

• The function names shown here are each button’s feature when used with the AVR 340. Most buttons have additional functions when used with other devices. See pages 51–52 for a list of these functions.

o make it easier to follow the instructions that refer

• to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

MAIN REMOTE CONTROL FUNCTIONS

MAIN REMOTE CONTROL FUNCTIONS 11

MAIN REMOTE CONTROL FUNCTIONS



IMPORTANT NOTE: The AVR 340’s remote may be programmed to control up to eight devices,

the AVR 340. Before using the remote, it is

including

mportant to

utton

emember to press theInput Selector

hat corresponds to the unit you wish

e t

to operate.

The AVR 340’s remote is shipped from the factory to operate the AVR 340 and most Harman Kardon CD or DVD players and cassette decks.The remote is also

apable of operating a wide variety of other products

c using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on page 48 to program the proper codes for the products in your system.

It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Device Control Selectors.The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR 340. (See pages 49–52 for information about alternate functions for the remote’s buttons.)

a Power Off Button: Press this button to place the AVR 340 or a selected device in the Standby mode.

b IR Transmitter Window: Point this window towards the AVR 340 when pressing buttons on the remote to make certain that infrared commands are properly received.

c Program Indicator: This three-color indicator is used to guide you through the process of programming the remote. (See page 48 for information on programming the remote.)

d Power On Button: Press this button to turn on the power to a device selected by pressing one of the

Input Selectors e.

e Input Selectors: Pressing one of these buttons

m three actions at the same time. First, if the

will perfor AVR 340 is not turned on, this will power up the unit.

it will select the source shown on the button as

Next, the input to the AVR 340. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press

VR Selector Button

the

f again to operate the

AVR 340’s functions with the remote.

f AVR Selector: Pressing this button will switch the remote so that it will operate the

AVR 340’s functions.

If the AVR 340 is in the Standby mode, it will also turn

VR 340 on.

the

g AM/FM Tuner Select: Press this button to select the AVR 340’s tuner as the listening choice. Pressing this button when the tuner is already in use will select between the AM and FM bands.

im Button:Press this button to activate the

h D

Dimmer function, which reduces the brightness of the front panel display, or turns it off entirely. The first press of the button shows the default state, which is full bright-

ess by indicating

Display Line

FD FULLin the Lower

ı. Press the button again within five

seconds to reduce the brightness by 50%, as indicated by

VFD HALF showing in the Lower Display Line

Press the button again within five seconds and the

ı.

ain display will go completely dark. Note that this set-

m ting is temporary, in that regardless of any changes, the display will always return to full brightness when the AVR is turned on. In addition, the

Power Indicator 2 will

always remain at full brightness regardless of the setting. This is to remind you that the AVR is still turned on.

i Test Button: Press this button to begin the sequence used to calibrate the AVR 340’s output levels. (See pages 25, 31 and 42 for more information on calibrating the AVR 340.)

j Sleep Button: Press this button to place the unit in the Sleep mode.After the time shown in the display, the AVR 340 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the following order:

See page 34 for more information on the Sleep Function. This button is also used to change channels on your TV when the TV is selected.

k DSP Surround Mode Selector: Press this but- ton to cycle through the DSP

VMAx and Stereo sur

round modes such as Hall, Theater, VMAx Near and Far, and Surround Off.This button is also used to tune channels when the

TV is selected using the device

Input Selector e.

l Night Mode: Press this button to activate the

Night mode.This mode is available in specially encoded digital sources, and it preserves dialogue (center channel) intelligibility at low volume levels

m Channel Select Button: This button is used to start the process of setting the AVR 340’s output levels to an external source. Once this button is pressed, use

⁄/¤

the adjusted,

⁄/¤

the

Buttons n

then press the Set

Buttons

to select the channel being

Buttonp,followed by

n again,

to change the level set

ting. (See pages 31 and 42 for more information.) However, Harman Kardon recommends that you first

as described on

m the EzSet/EQ procedure

perfor

pages 25 to 27.

⁄/¤

uttons:These multipurpose buttons are

used to change or scroll through items in the onscreen menus, make configuration settings such as digital inputs or delay timing, or to select surround

odes.When changing a setting, first press the button

m for the function or setting to be changed (e.g., press the

DSP Surround Mode Selector k to select a

sound field mode or the

o change a digital input) and then press one of these

uttons to scroll through the list of options or to

Digital Select Button q

increase or decrease a setting. The sections in this manual describing the individual features and functions contain specific information on using these buttons for each application.

‹/›

Buttons: These buttons are used to change

the menu selection or setting during some of the setup procedures for the AVR 340.

p Set Button: This button is used to enter settings into the AVR 340’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.

q Digital Select: Press this button to assign one of the digital inputs

*(ﬁf to a source. (See pages 22 and 38 for more information on selecting digital inputs.)

r Numeric Keys: These buttons serve as a 10- button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, Cable or SAT has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.

I Tuner Mode: Press this button when the tuner is in use to select between automatic tuning and manual tuning.

When the button is pressed so that

MANUAL appears in the Lower Display Line ı, pressing the

Tuning Buttons 9u will move the

frequency up or down in single-step increments. When the FM band is in use, pressing this button when a station’s signal is weak will change to monaural reception. (See page 41 for more information.)

J Direct Button: Press this button when the tuner is in use to start the sequence for direct entr

After pressing the button,

station’s frequency press the proper

Numeric Keys r to select a sta-

y of a

simply

tion. (See page 41 for more information on the tuner.)

12 MAIN REMOTE CONTROL FUNCTIONS

MAIN REMOTE CONTROL FUNCTIONS

The

Bridge

The

Bridge

uning Up/Down:When the tuner is in use,

u T

these buttons will tune up or down through the selected frequency band. If the

Tuner Mode Button s&

has been pressed so that AUTO appears in the on-

creen display and

ower Display Lineı,pressing

and holding either of the buttons for three seconds will cause the tuner to seek the next station with acceptable signal strength for quality reception. When

ppears in the Lower Display Lineı,pressing these

uttons will tune stations in single-step increments. (See

MANUAL

page 41 for more information.)

SD Button:Press this button to activate the

v O

n-Screen Display (OSD) system used to set up or

O adjust the AVR 340’s parameters.

w Dolby Mode Selector: This button is used to select from among the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II or IIx,

or Dolby Virtual Speaker modes or Dolby 3 Stereo.When a Dolby Digital-encoded source is in use, the Dolby Digital mode may also be selected. When the headphones are in use, this button selects from among the Dolby Headphone modes. (See pages 36–37 and 40 for the available Dolby surround mode options.)

x DTS Digital Mode Selector: When a DTS- encoded digital source is selected, each press of this button will scroll through the available DTS modes. The specific choice of modes will vary depending on whether the source material contains DTS-ES 6.1 Discrete encoding. When a DTS source is not in use, this button has no function. (See pages 36 and 40 for the available DTS digital options.)

y Logic 7 Mode Select Button: Press this button to select from among the available Logic 7 surround modes. (See pages 36 and 40 for available Logic 7 options.)

z Skip Up/Down Buttons: These buttons do not have a direct function with the

but when

VR 340, used with a compatibly programmed CD or DVD player they will change to the next or previous track.

` Transport Controls: These buttons do not have any functions for the

AVR 340, but they may be programmed for the forward/reverse play operation of a wide variety of CD or DVD players, and audio or video cassette recorders.When the DMP

these buttons may be used to oper

source is in use

, ate some functions on a compatible iPod if it is docked in

The Bridge.

See page 42 for more

information on using .

When the remote is used to control the AVR, or the VID2 or VID3 device, by default these buttons are programmed to operate the DVD player. However, you

ay use the Transport Control Punch-Through feature

escribed on page 50 to program these buttons to

d operate another device’s transport controls when the AVR, VID2 or VID3 has been selected.

R Stereo Mode Select Button: When the button is pressed so that the

Lower Display Line ı, with only the Surr Off

Surround Mode Indicator

te in a bypass mode with true, fully analog, two-chan-

SURROUND OFF appears in

ˆ lit, the AVR will oper-

nel left/right stereo mode with no surround processing or bass management,

unlike other modes where digital processing is used. When the button is pressed so that

SURROUND OFF appears in the Lower Display Line Surround Mode Indicators

ı, with both the DSP and Surr Off

ˆ lit, you may enjoy a

two-channel presentation of the sound along with the benefits of bass management. Depending on whether your system is configured for 5.1 or 6.1/7.1 channels, the next press of the button will cause either 5 CH STEREO or 7 CH STEREO to appear, and the stereo signal will be routed to all five (or seven) speaker channels. (See pages 37 and 40 for more information on stereo playback modes.)

S DTS Neo:6 Mode Select: Press this button to select a DTS Neo:6 mode.These modes take a twochannel stereo- or matrix surround-encoded source and create a full five-, six- or seven-channel sound field. (See pages 36 and 40 for the DTS Neo:6 options.)

T Macro Buttons: Press these buttons to store or

, which is a preprogrammed sequence

“Macro”

recall a of commands stored in the remote. (See page 48 for more information on storing and recalling macros.)

U Disc Skip Button: This button has no direct function for the AVR 340 but is most often used to change to the next disc in a CD or DVD player when the remote is programmed for that type of device. (See page 49 for more information on using the remote with products other than the AVR 340.)

V Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the some source devices, such as CD players, VCRs and

cassette decks

Selectors

AVR 340’s memory. When

are selected using the device

these buttons may function as

Chapter Step or Track Advance. W Clear Button: Press this button to clear incorrect

entries when using the remote to directly enter a radio station’

s frequency

X Memory Button: Press this button to enter a radio station into the AVR 340’s preset memory. First, tune

Input

the desired station, and then press this button. Two underline indicators will flash at the right side of the Upper Display Line P, and within five seconds

ress the

etween 01 and 30 that you wish to assign to the

umeric Keys

or the preset number

r f

station. (See page 41 for more information.) Y Delay/Prev Ch.: Press this button to begin

the process for setting the delay times used by the AVR 340 when processing surround sound. After

ressing this button, the delay times are entered by

p pressing the

⁄/¤

DELAY

nel. Press the

⁄/¤

Set Button p and then using the

Buttons n to select A/V SYNC

or the delay setting for any available chan-

Set Button p, and then use the

Buttons n to change the setting. Press the

Set Button p again to complete the process. (See

page 30 for more information.) However, we recommend that you first perform the EzSet/EQ procedure, as described on pages 25–27.

Z Speaker Select: Press this button to begin the process of configuring the AVR 340’s bass management system for use with the type of speakers used in your system. Once the button has been

⁄/¤

pressed, use the channel you wish to set up. Press the p and then use the the appropriate speaker size. Press the p to enter the new setting, and then use the

Buttons n to select the

Set Button

⁄/¤

Buttons n to select

Set Button

⁄/¤

Buttons n again to select another channel to configure.When all adjustments have been completed, press the Set Button p twice to exit the settings and return to normal operation. (See page 28 for more information.) However, Harman Kardon recommends that you first perfor

m the EzSet/EQ procedure,

as described on pages 25–27. a Multiroom Button: Press this button to begin

the process of activating the Multiroom system, or changing the source input or volume level for the remote zone. Press the

⁄¤ Buttons n to scroll

to the on/off, source input or volume level setting, and then press the setting. the options

Set Button p to access the desired

Use the

⁄¤ Buttons n to scroll through

and the

Set Button p to select.

(See

page 46 for information on the Multiroom system.) b Volume Up/Down: Press these buttons to raise

or lower the system volume. By default, the

Up/Down Buttons

y to control the

tor

b are programmed at the fac-

VR 340’s volume

Volume

no matter which

, source device has been selected (except TAPE). You may reprogram these buttons to control the volume of

using the Volume

another device

such as your

TV Control Punch-Through instructions found on page 50.

c TV/Video Selector: This button does not have a direct function on the

AVR 340, but when used with a

MAIN REMOTE CONTROL FUNCTIONS 13

The

Bridge

The

Bridge

The

Bridge

The

Bridge

MAIN REMOTE CONTROL FUNCTIONS

compatible VCR, DVD or satellite receiver, pressing this button will switch between the output of the device and the external video input. Consult the owner’s man-

al for your specific player or receiver for the details of

ow it implements this function.

d D

When Harman Kardon’s (optional) is connected to

Connector

as the audio source input device for the AVR 340. In addition, if a video display is connected to one of the Video Monitor Outputs gY, the iPod’s messages will appear on screen, and in the

Display Lines no, the Set Button p and the Transport Controls

to operate many functions. See page 42, and the manuals for The Bridge and your iPod for more information.

6-Channel/8-Channel Direct Input: Press

this button to select the device connected to the 6/8-Channel Direct Inputs X. more information.)

When the device connected to the

Direct Input

DVD or DVD-Audio player with an onboard audio decoder, you must first select that video source by pressing its button to choose the device connected to the

Channel Direct Input

that if you desire, you may select any video source to be used in conjunction with the

Input

f Mute: Press this button to momentarily silence the AVR 340 or TV set being controlled, depending on which device has been selected. When the AVR 340 remote is being programmed to operate another device this button is pressed with the e to begin the programming process. (See page 48 for more information on programming the remote.)

igital Media Player (DMP) Selector:

Digital Media Player (DMP)

j and a compatible iPod is docked in

pressing this selector will select the iPod

Upper and Lower

PQ. The ⁄

/¤/‹/

› Buttons

` may be used to navigate the iPod and

(See page 34 for

6/8-Channel

is also a video source, such as a

Input Selector e, then press this

as the audio source. Note

6/8-Channel Direct

as the audio source.

Input Selector

6/8-

Button

14 MAIN REMOTE CONTROL FUNCTIONS

ZONE II REMOTE CONTROL FUNCTIONS

The

Bridge

The

Bridge

The

Bridge



The

Bridge

The

Bridge

POWER

MUTE

M/FM

ID 1

DMP/The Bridge

OLUME

PLAY

SKIP

TUNING

PRESET

ID 2

DVD

ID 3

VID 4

TAPE

ISC

SKIP

ISC

ower Off Button:When used in the room

where the AVR 340 is located, press this button to place the unit in Standby.When it is used in a remote room with a sensor that is connected to the

ultiroom IR Input Jack ∞,this button turns the

Multiroom system on and off.

olume Up/Down Buttons:When the Zone II

remote is used in the room where the AVR 340 is located, press this button to raise or lower the volume in that room. When it is used in a remote room with a

ensor that is connected to the

Jack

∞, this button will raise or lower the volume in

ultiroom IR Input

the remote room.

VR Selector:Press this button to turn on

∫

he AVR 340 and to access the volume and mute

t controls.The input in use when the unit was last on will be selected.

ause Button:Press this button to activate the

Pause function on compatible Harman Kardon CD, DVD or cassette deck products, or on your iPod when DMP has been selected.

AM/FM Tuner Selector: Press this button to

select the Tuner as the input to the Multiroom system. Press it again to change between the AM and FM bands. Pressing this button will also turn on the AVR 340’s multiroom system if it is off, even when

Stop Button: Press this button to activate the

Stop function on compatible Harman Kardon CD, DVD or cassette deck products. It will have no effect on your iPod when DMP has been selected.

the AVR is in Standby mode.

∆

Play Button: Press this button to activate the

∂

Input Selectors: Press one of these buttons to

select a specific input. Pressing this button will also turn on the AVR 340’s multiroom system if it is off,

Play function on compatible Harman Kardon CD, DVD or cassette players or on your iPod when DMP

has been selected.

even when the AVR is in Standby mode.

Tuning Up/Down – Fast Play Buttons: When

≠

Preset Up/Down – Track Skip Buttons: When

the AVR 340’s tuner is selected as the input source, these buttons will move up or down through the list of stations that have been stored in the preset memory. When a CD or DVD changer or player is selected, these buttons activate the Forward or Reverse Track or Chapter Skip functions.

the Zone II remote is used in the same room as the AVR 340, these buttons may be used to change the frequency of the tuner. These buttons may also control the Fast Play or Fast Reverse functions of compatible Harman Kardon CD, DVD or cassette decks in the same room, or from a remote room when an IR link is connected to the AVR 340. These buttons will select the previous or next track on your iPod when

Disc Skip Buttons: Press these buttons to

DMP has been selected.

change discs on compatible Harman Kardon CD or

Power Off Button

∫

AVR Selector

AM/FM Tuner Selector

∂

Input Selectors

≠

Preset Up/Down – Track Skip Buttons

Disc Skip Buttons

olume Up/Down Buttons

Pause Button

Stop Button

∆

Play Button

Tuning Up/Down – Fast Play Buttons

Mute Button

DVD changers or players. When DMP has been selected, the left (–) button has the same effect as scrolling the iPod’s Click Wheel counterclockwise, and the right (+) button has the same effect as scrolling the Click Wheel clockwise.

NOTES:

•

The Zone II remote may be used in either the same room where the AVR 340 is located or in a separate room with an optional infrared sensor or A-BUS product that is connected to the AVR 340’s

Jack

∞. When it is used in the same room as the AVR 340, it will control the functions of the AVR 340 or any

compatible Harman Kardon products in that room. When it is used in a separate room via a sensor connected to

Multiroom IR Input Jack ∞, the buttons for Power, Input Source,Volume and Mute will control the source

the and volume for the second zone,

as connected to the

Mute Button: When the Zone II remote is used

in the room where the AVR 340 is located, press this button to temporarily silence the unit. When it is used in a remote room with a sensor that is connected

Multiroom IR Input Jack ∞, this button

to the will temporarily silence the feed to the remote room only. Press the button again to return to the previous volume level.

Multiroom IR Input

Multiroom Audio Output Jacks ™.

(See page 46 for

complete information on using the Multiroom system.)

To make it easier to follow the instructions that refer to the controls and connectors in this illustration, a larger

• copy may be downloaded from the Product Support section for this product at www.harmankardon.com.

ZONE II REMOTE CONTROL FUNCTIONS 15

INSTALLATION AND CONNECTIONS

The

Bridge

The

Bridge

The

Bridge

The

Bridge

INSTALLATION AND CONNECTIONS

System Installation

After unpacking the unit, locating it in a place with adequate ventilation and placing it on a solid surface capable of supporting its weight, you will need to make the con-

ections to your audio and video equipment.

n IMPORTANT NOTE: For your personal safety and to

avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the

VR and ALL source equipment from the AC outlet

A before making any audio or video system connections.

Audio Equipment Connections

e recommend that you use high-quality interconnect

W cables when making connections to source equipment and recorders to preserve the integrity of the signals.

1. Connect the analog outputs of a CD player to the

CD Audio Inputs £.

NOTE: When the CD player has both fixed and

variable audio outputs, it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that it is distorted.

2. Connect the analog Play/Out jacks of a cassette deck, MD, CD-R or other audio recorder to the Tape Input Jacks f. Connect the analog Record/In jacks on the recorder to the

Output Jacks

g on the AVR 340.

3. Connect the output of any digital sources such as a CD or DVD changer or player, advanced video game, a digital satellite receiver, HDTV tuner or digital cable set-top box or the output of a compatible computer sound card to the Coaxial Digital Audio Inputs ﬁf*(.We recommend connecting the coaxial digital audio output of your DVD player to the

Audio Input

f, since that digital input is assigned to the DVD source by default. The Video 2/Cable/Sat source defaults to the

Digital Audio Input

ﬁ. If your cable television set-top box or satellite receiver is equipped with an optical digital audio output, we recommend that you connect it to this input to obtain the benefits

-quality digital audio (such as PCM, Dolby

of higher Digital 2.0 or Dolby Digital 5.1 signals when broad cast by your cable or satellite provider).

NOTE: If you wish for your digital source device to be available for use by the multiroom system, you will need to connect its analog audio outputs to the appropriate inputs on the

as the multiroom sys-

VR 340, tem is not capable of distributing digital signals to the remote zone.

4. Connect the

Outputs

Coaxial or Optical Digital Audio

de on the rear panel of the

Tape

Optical and

Coax 1 Digital

Optical 1

340 to

the matching digital input connections on a CD-R or MiniDisc or other digital recorder.

. Assemble the AM Loop Antenna supplied with the

unit so that the tabs at the bottom of the antenna loop snap into the holes in the base. Connect it to the

AM Antenna Terminals h.

6. Connect the supplied FM antenna to the ohm)

Connection ¡.

The FM antenna may be an external roof antenna, an inside powered or wirelead antenna or a connection from a cable TV system. If the antenna or connection uses 300-ohm twin-lead cable, you must use an optional 300ohm-to-75-ohm adaptor to make the connection.

7. With the AVR 340 turned off, connect the optional Harman Kardon to

Player (DMP) Connector

j. Your compatible iPod may be docked in when you wish to use it as an audio source device.Video materials stored on the iPod may not be viewed via .

8. Connect the front, center, surround and surround back speaker outputs

⁄¤‹› to the respec-

tive speakers.

To ensure that all the audio signals are carried to your speakers without loss of clarity or resolution, we suggest that you use high-quality speaker cable. Many brands of cable are available and the choice of cable may be influenced by the distance between your

the type of speakers you

speakers and the receiver

, use, personal preferences and other factors. Your dealer or installer is a valuable resource to consult in selecting the proper cable.

Regardless of the brand of cable selected, mend that you use a cable constructed of copper with a gauge of 14 or smaller.

the lower the number, the thicker

in specifying cable

the cable.

Cable with a gauge of 16 may be used for short runs

of less than 10 feet. We do not recommend that you use cables with an AWG equivalent of 18 or higher, due to the power loss and degradation in perfor that will occur.

Cables that are run inside walls should have the appro priate markings to indicate listing with UL, CSA or other appropriate testing agency standards. Questions about running cables inside walls should be referred to your installer or a licensed electrician who is familiar with

FM (75-

Digital Media

we recom-

multistrand

Remember that

mance

the NEC and/or the applicable local building codes in your area.

hen connecting wires to the speakers, observe

W proper polarity. Note that the positive (+) terminal of each speaker connection may carry a specific color code, as noted on page 8. However, many speakers

till use a red terminal for the positive (+) connection.

s Connect the “negative” or “black” wire to the same terminal on both the receiver and the speaker.

OTE:While most speaker manufacturers adhere to

n industry convention of using black terminals for

a negative and red ones for positive, some may vary from this configuration. To ensure proper phase and optimal performance, consult the identification plate on your speaker or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker’s manufacturer.

We also recommend that the length of cable used to connect speaker pairs be identical. For example, use the same length piece of cable to connect the front-left and front-right or surround-left and surround-right speakers, even if the speakers are a different distance from the AVR 340.

9. The connections to a subwoofer are normally made via a line-level audio connection from the Subwoofer Output • to the line-level input of a subwoofer with a built-in amplifier. When a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofers. If you are using a powered subwoofer that does not have line-level input con-

, follow the instructions furnished with the

nections speaker for connection infor

mation.

10. If an external multichannel audio source with 5.1,

6.1 or 7.1 outputs such as an external digital DVD-Audio or SACD player

processor/decoder

, is used, connect the outputs of that device to the

6/8-Channel Direct Inputs X.

Video Equipment Connections

Video equipment is connected in the same manner as audio components. cables is recommended to preser

The use of high-quality interconnect

ve signal quality.

1. Connect a VCR’s, DVD recorder’s, personal video recorder’s or other video source’s audio and video Play/Out jacks to the

Video 1 Audio/Video and/or

S-Video Input Jacks Ra on the rear panel. The

Audio and

should be connected to the

Video Record/In jacks on the recorder

Video 1 Audio/Video

and/or S-Video Output Jacks Tb on the AVR 340. Although any video device may be connected to these jacks, we recommend connecting your video recorder to take advantage of the fact that the

INSTALLATION AND CONNECTIONS

remote control is preprogrammed with video recorder product codes for the Video 1 device.

. Connect the analog audio and video outputs of

a satellite receiver, cable TV converter, television set or any other video source to the

Audio/Video and S-Video Input Jacks

lthough any video device may be connected to

A these jacks, we recommend connecting your cable TV converter or satellite receiver to take advantage of the fact that the remote control is preprogrammed with the product codes of these device

ypes for the Video 2 device.

3. Connect the analog audio and video outputs of a television or other video device to the

Audio/Video

the rear panel. Although any video or audio device may be connected to these jacks, we recommend connecting your television so that you may take advantage preprogrammed Video 3 device.

Important: If you are using the television only as a display device (i.e., if you receive your TV programs through a cable box or satellite receiver), do not connect the television’s outputs to the

Audio/Video

or to any other inputs on the AVR 340.

4. Connect the analog audio and video outputs of a

DVD or laser disc player to the and S-Video Inputs hZ.

5. Connect the digital audio outputs of a DVD player, satellite receiver, cable box or HDTV converter to the appropriate ﬁf*(. defaults to the the Video 2/Cable/Sat source defaults to the

Optical 1 Digital

sources default to their analog inputs, although any source may be assigned to any digital audio input on the receiver.

NOTE: When connecting a device such as a digital cable box or other set-top tuner product with a digital audio output, both the digital and analog outputs of the product to your AVR.The audio input polling feature of the AVR will then be able to make certain that you have a constant audio feed, since it will automatically switch the audio input to the analog jacks if the digital feed is interrupted or if it is not available for a particular channel.

Connect the

Output

and S-Video Input Jacks We on

of the fact that the remote control is

with TV product codes for the

and S-Video Input Jacks We,

Optical or Coaxial Digital Inputs

Remember that the DVD source

Coaxial 1 Digital Input f, and

Audio Inputﬁ.All other

we recommend that you connect

Video and/or S-Video Monitor

gY jacks on the receiver to the compos-

Video 2

Uc.

Video 3

DVD Audio/Video

ite or S-video input of your analog television monitor or video projector.

othyour video display monitor and at least one

. If b

video source device (such as a DVD player or HDTV set-top box) are equipped with component video capability, then you may connect the compo-

ent video outputs of the device to one of the two

n Component Video Inputs ‡°. In that case, you will not need to connect the

Output

Y or the S-Video Monitor Output P

to your video display, as the AVR 340 will convert

omposite and S-video signals to component

This means you only have to connect one

video cable from the AVR to the video display. You will also be able to view the AVR 340’s on-screen menu displays using just the component video connection, unless the source device is high-definition (720p or 1080i) video, in which case you should either switch to a 480p source or connect the

Video Monitor Output Y or the S-Video Monitor Output

view the on-screen displays.

8. It is recommended that you connect a DVD player

or a digital video recorder to the

Video 1 Inputs

DVD, CD, Tuner and Tape sources by default. Thus, whenever any of these sources is selected, you may view the component video output of the device connected to the enabling you to view and listen to different sources.

8. Similarly, it is recommended that you connect any

other audio/video device equipped with component video outputs, such as a DVD-Audio or SACD player, or HDTV set-top box, Video 3

Component Video 2 Inputs ° are

as the assigned to the Video 1, Video 2, Video 3 and 6-/8-channel source audio inputs by default.

8. However, you may connect any component video

source to either set of component video inputs, as they are assignable to any source instructions on page 22. You will still need to connect either the analog or digital audio outputs the 6-/8-channel audio outputs, of your component video device to the analog audio inputs corresponding to the source (such as DVD or Video 2 for a cable converter box), Coaxial Digital Audio Inputs ﬁf*(.

8. If the component video inputs are used, connect the

Component Video Monitor Outputs ﬂ to

the component video inputs of your or display device.You will also be able to view your composite and S-video sources through this connection, benefiting from the higher quality and superior appearance of component video.

P to your video display to

‡, as this input is assigned to the

Component Video 1 Inputs ‡,

to the

sources, or the 6-/8-channel direct inputs,

or to any of the

Video Monitor

Component

Video 1, Video 2 or

following the

Optical or

projector

TV,

9. If you have a camcorder, video game or other audio/video device that is connected to the AVR on a temporary rather than permanent basis, connect

he audio, video and digital audio outputs of that

evice to the V

d front panel. A device connected here is selected as the Video 4 input, and the digital inputs must be assigned to the Video 4 input. (See page 22 for

ore information on input configuration.)

NOTE: The AVR 340 is shipped with two covers that may be installed over the front-panel input

acks when they are not in use.

10. When connecting the AVR 340 to a “digital-ready”,

“HDTV-compatible” or high-definition display (which is any device capable of accepting an input signal of 480P or higher), you are able to take advantage of the unit’s advanced video processing circuitry which converts all video signals to a 480P output. Since the AVR 340 displays the on-screen menus with upconverted video, the connection from the AVR 340 to the display need only be one set of Y/Pr/Pb component video cables to the Component Video Monitor Output ﬂ.

11. When connecting the AVR 340 to a standard,

analog video display that has standard composite and S-video inputs only, component video inputs may not be used. In this case, connect the Video and matching composite and S-video inputs on your video display, depending on which types of video are used by your source devices. If both types of video are used by different source devices, than both separately connected to your television.

VIDEO CONNECTION NOTES:

• When the component video jacks are used, the onscreen menus are not visible with high-definition video (720p or 1080i), standard composite or S-video input on your to a 480p video source, to view them.

• When source devices such as a progressive scan

DVD player or an HDTV set-top box are connected to the you wish to take advantage of the record outputs or have video routed to a second room, it is also necessary to connect the standard, composite or Svideo outputs of the source device to the The record outputs and multiroom system cannot accept component inputs, nor are component inputs down-converted for use with these outputs

When connecting a video source to the A

• you may use either composite, component or S-video, but only one type of video may be connected for each device.

ideo 4 Inputs*(ÓÔon the

S-Video Monitor Outputs PY to the

Video Monitor Outputs PY must be

and you must switch to the

VR 340 via component video connections

VR 340.

VR 340,

TV, or

,if

INSTALLATION AND CONNECTIONS

System and Power Connections

The AVR 340 is designed for flexible use with multiroom system and external control components.

Remote Infrared (IR) Control of the AVR or Source Devices

f the receiver is placed behind a solid or smoked

I glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used.

onnect the output of the remote sensor to the

emote IR Input

f other components are also prevented from receiving

I remote commands, only one sensor is needed. Simply use this unit’s sensor or a remote eye by running a connection from the the Remote IR Input jack on Harman Kardon or other compatible equipment.

When controlling non-Harman Kardon source devices, the device may require the full carrier signal embedded within the IR command, rather than the “stripped” signal used by Harman Kardon and many other devices. In these cases you may need to connect the Remote IR Carrier Output § to the remote IR input of your device (or to an optional, external IR “blaster”), rather than using the standard

Jack

‚. If you are in doubt as to which IR Output jack to use for the equipment in your system, contact your dealer or installer, or consult the manufacturer’s support site and ask whether the unit to be controlled uses “full carrier” or “stripped carrier” IR commands. When “full carrier commands” are used, make the connection to the Otherwise, make the connection to the

Output Jack NOTE: All remotely controlled components must be

linked together in a “daisy chain.” Connect the IR OUT jack of one unit to the IR IN of the next to establish this chain.

Multiroom Connections

The AVR 340 is equipped with multizone capabilities that allow it to send a separate audio source to the remote zone from the one selected for use in the main room.

Depending on your system’s requirement, three options are available for audio connection:

Option 1: Use high-quality, nect cable from the AVR 340’s location to the remote room. In the remote room, connect the interconnect cable to a stereo power amplifier. The amplifier will be connected to the room’s speakers. plug the audio interconnect cables into the

Audio Outputs

ack.

ª j

Remote IR Output ‚ jack to

Remote IR Output

Remote IR Carrier Output §.

Remote IR

‚.

shielded audio intercon

At the

™ on the AVR 340’s rear panel.

VR 340,

Multiroom

Option 2: Connect the Multiroom Audio Outputs

™ on the AVR 340 to the inputs of an optional stereo power amplifier. Run high-quality speaker wire

rom the amplifier to the speakers in the remote room.

f Option 3: Taking advantage of the AVR 340’s built-in

seven-channel amplifier, it is possible to use two of the amplifier channels to power speakers in the remote

oom. When using this option, you will not be able to

r use the full 7.1-channel capabilities of the AVR 340 in the main listening room, but you will be able to add another listening room without external power amplifiers.To use the internal amplifiers to power a remote zone, connect the speakers for the remote room location to the

Outputs

need to configure the amplifiers for surround operation by changing a setting in the

SETUP

on page 46. NOTE: The AVR 340’s multiroom system is only capa-

ble of distributing analog audio sources to the remote zone.Therefore, when connecting your digital audio equipment (e.g., CD or DVD players) as described on page 16, make sure to use both analog and digital audio connections to ensure that the devices will be available to the multiroom system.

IR Control From the Remote Room

For all options, you may connect an optional IR sensor in the remote room to the AVR 340 via an appropriate cable. Connect the sensor’s cable to the

IR Input

(or main) remote to control the room volume and any source devices connected to the

Jack

§ as described above.Alternatively, you may install an optional volume control between the output of the amplifiers and the speakers, which will only enable you to adjust the volume of playback in the remote room.

A-BUS®Installation Connections

The AVR 340 is among the few receivers available that offer built-in A-BUS/ with an optional efits of remote zone operation without the need for an external power amplifier.

To use the AVR 340 with an approved A-BUS product, 5 wiring that is properly rated for the specific in-wall installation. Terminate the wiring at the receiver end to a standard RJ-45 connector in compliance with the instructions furnished with the A-BUS product.

Y AVR 340 with no further equipment needed. If you wish to connect more than one A-BUS module, an optional, that capability.

Surround Back/Multiroom Speaker

¤. Before using the remote room, you will

MULTI ROOM

menu, following the instructions shown

Multiroom

∞ on the AVR 340 and use the Zone II

Remote IR Output

‚ or to the Remote IR Carrier Output Jack

READY operation. When used

A-BUS product, you have all the ben

simply connect it to the AVR 340 using Category

ou may connect a single

external A-BUS hub may be used to provide

A-BUS module to the

Contact your dealer or visit www.harmankardon.com for more information on other A-BUS products available from Harman Kardon. No further installation

r adjustment is needed, as the A-BUS jack on the

VR 340 routes the signals to their proper destination.

A The output fed to the A-BUS jack is determined by the AVR 340’s multiroom system and menus.

f the A-BUS module is equipped with an IR sensor,

I you may use the Zone II or main remote to control the room volume and any source devices connected to

Remote IR Output Jack ‚ or to the Remote

the

IR Carrier Output Jack

wer Connections

AC P

This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with high-current-draw equipment, such as power amplifiers. The total power draw to each outlet may not exceed 100 watts.

Switched AC Accessory Outlet b will receive

The power only when the unit is on. This is recommended for devices that have no power switch or a mechanical power switch that may be left in the “ON” position.

NOTE: Many audio and video products go into a Standby mode when they are used with switched outlets, and cannot be fully turned on using the outlet alone without a remote control command.

Unswitched AC Accessory Outlet c will

The receive power as long as the unit is plugged into a powered AC outlet.

Once the

AC Power Cord a is connected, you are

almost ready to enjoy the AVR 340’s incredible power and fidelity!

§ as described above.

18 INSTALLATION AND CONNECTIONS18 INSTALLATION AND CONNECTIONS

SYSTEM CONFIGURATION

Center Speaker

Video Screen

Front Right

Speaker

Front Left

Speaker

Side Surround

Left Speaker

Alternate placement

for Side Surround

Left Speaker

Side Surround

Right Speaker

Alternate placement

for Side Surround

Right Speaker

110°

150°

110°

150°

30° 30°

When all audio, video and system connections have been made, the final steps before listening to your new AVR are to make the configuration adjustments that

ailor the unit to the other components in your system

s well as to accommodate your personal listening

a preferences.A few minutes spent to correctly calibrate and configure your system will greatly add to your listening pleasure.

Speaker Selection and Placement

While the most seamless surround sound reproduction comes from the use of speakers with identical or carefully matched driver elements at each position, no matter which brand or type of speakers you prefer, it is always best to use the same model or series for the left front, center and right front speakers. Similarly, it is also desirable to use the same model or series for the surround speakers.This ensures that the soundstage will be relatively seamless and it eliminates the possibility of sonic discordance when a sound moves from one side of the room to the other.

Speaker Placement

Once you have selected your speakers, it is important that they be placed in positions that enable them to do the best job of reproducing the sound as it was meant to be heard, regardless of the program content. Particularly in multichannel 5.1, 6.1 or 7.1 systems, the placement of speakers can have a noticeable impact on the accuracy of the surround process.

When placing your speakers in a listening room, picture an imaginary circle starting at the center of your video screen that arcs around the room with the prime listening position, or “sweet spot,” at the center of the circle. Depending on the number of speakers in your

there is a recommended placement along the

system, circle for each speaker, though the specific construction of your room, taking into account the available walls, bookcases, or floor space at which the speakers may be placed will obviously have some impact on where the speakers are ultimately located. As a general rule, try to place all speakers so that they are positioned at the same height as your ears when you are seated at the prime listening position.

Use the following suggestions as a guide, and make the changes needed to fit the speakers to your room. Don’t be afraid to experiment a bit until you find the right combination of locations that works for you. At the end of the day,

there is no real “right” or “wrong” place to put the speakers; work to optimize their locations so that audio moves across the front of the room smoothly, without seeming to jump from one speaker

to another

Center Channel Speaker

The ideal location for the center channel speaker is at “0 degrees” in our circle, directly in front of the prime listening position.

Place the center channel speaker as

close to the top (or bottom) of the video screen as

possible so that when you position the front left/right speakers, the tweeters of all three front channel speakers are within 24" of one another.

Front Left/Right Speakers

The recommended placement for front left/right speakers is at the 30-degree position with reference to the center channel speaker. The distance between

hem should be about the same as the distance from

t the center channel speaker to the prime listening position.

Although the natural tendency is to place the speakers s in line with the video screen, is to angle the speakers slightly (“toe in”) so that they point at the prime listening position.

Surround Speakers for 5.1 Systems

In a 5.1 surround system, an additional pair of left/right speakers is added. Although many believe that these speakers should be placed at the rear of the room, the preferred position for them is at the sides of the room, with rear placement a second

o they are parallel to the wall behind them, and thus

he preferred placement

option when room conditions prevent the use of sidemounted surround speakers.

When side-wall placement is possible, place the left/right surround speakers at a point that is 110 degrees along our circle from the center of the video screen. This translates to placing them to the side and slightly behind your preferred listening position. If pos-

ible, angle the speakers in slightly so that they are

s pointing towards the listener’s ears.

If it is not possible to place the surround speakers at the sides of the room, the alternate position is at the

ack of the room, at a spot that is about 150 degrees

b around our circle from the center of the video screen. Another way to spot the optimal, alternate rear-wall mounting position is to place the left surround speaker on the back wall so that it points directly at the front right speaker, and to have the right surround speaker point directly at the front left speaker. If possible, aim the surround speakers so that they point “in” toward the listening area, rather than perpendicular to the walls.

5.1 Placement Diagram

SYSTEM CONFIGURATION

Center Speaker

Video Screen

Front Right

peaker

Front Left

peaker

Side Surround

Left Speaker

Side Surround

ight Speaker

Back Surround

Speaker

istening Position

10° 110°

30°

Center Speaker

Video Screen

Front Right

Speaker

Front Left

Speaker

Side Surround

Left Speaker

Back Surround

Left Speaker

Side Surround Right Speaker

Back Surround Right Speaker

90°

150°

90°

150°

30° 30°

6.1-Channel System

Surround Speakers for 6.1 Systems

A 6.1 surround speaker adds an additional center back surround speaker to the system, enabling you to enjoy the benefits of advanced surround modes such as Dolby Digital EX, DTS-ES and Harman Kardon’s

y Logic 7/7.1 processing.

proprietar To step up to a 6.1 system, first place the speakers

for a 5.1 system, as shown on page 19. The “sixth” speaker should ideally be placed at the center of the

s rear wall, pointing directly toward the front

room’ center channel speaker

NOTE: The 6.1-channel configuration is not recommended for the AVR 340.We strongly recommend a

7.1-channel installation as described below.When

6.1-channel materials are played through a 7.1-chan nel system, the same surround back channel information is played through both the left and right surround back speakers

If you are only able to install a single surround back speaker at this time, you will not be able to run the full EzSet/EQ 7.1-channel calibration procedure. In that case, we suggest you install all of your speakers except the surround back speaker, and run the

EzSet/EQ procedure for a 5.1-channel system (see page 26). After EzSet/EQ has finished, single surround back speaker to the

Back Speaker Outputs

tions starting on page 27 for manual setup to manually configure your surround back speaker.

left Surround

B. Then follow the instruc-

connect the

We recommend that you consider adding a second surround back speaker as soon as possible.

Surround Speakers for 7.1 Systems

For the ultimate home theater experience, a 7.1 surround system uses both traditional surround left/right channels and a surround back left/right speaker pair. In a 7.1 system, the front left/center/right speakers

emain in the same place as they would be for a 5.1

r or 6.1 system, but due to the number of speakers involved, the placement of the surround speakers is different.

In a 7.1 system, you should place the main surround left/right speakers at the 90-degree point on our cir cle.A good way to visualize proper surround speaker positioning for 7.1 is to place the speakers directly to the left and right of the ears of someone sitting in the prime listening spot. The two speakers should ideally face toward each other.

The additional set of Surround Back Left/Right speakers is placed at about 150 degrees on the circle, pointing inward toward the listening area. The easiest way to visualize the placement of these speakers is to place the surround back left speaker directly opposite the right front speaker and to place the surround back left speaker directly opposite the left front speaker.

Since subwoofers produce nondirectional sound, they may be placed almost anywhere in a room. Actual

7.1-Channel System

20 SYSTEM CONFIGURATION

SYSTEM CONFIGURATION

** MASTER MENU **

INPUT SETUP AUDIO SETUP SURROUND SELECT EzSet/EQ MANUAL SETUP MULTI-ROOM ADVANCED

placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by

lacing it in the front of the room, about six inches

rom a wall, or near the front corner of the room.

f Another method is to temporarily place the subwoofer at your normal listening position, and then walk around the room until you find a spot where the sub-

oofer sounds best. Place the subwoofer in that spot.

w You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your

istening room.

NOTES ON SPEAKER PLACEMENT:

1. The limitations of your listening room, including the

placement of walls and furniture, may make it difficult to follow the speaker placement suggestions shown above. Depending on the specific layout of the room, here are some ways to compensate for unusual conditions:

• Try to follow the suggested placement, but move the speakers within a few feet from the preferred locations.

• Regardless of where they are placed, always try to make certain that the main surround speakers are the same distance from the front speakers. (For example, try not to have the right surround speaker further back into the room than the left surround speaker.)

• If it is not possible to wall-mount or place speakers on a shelf, consider the use of optional floor stands, available for many speakers.

2. When using ceiling mounted in-wall speakers, follow the same guidelines shown for conventional floor or shelf-mounted speakers.

3. When you have reassigned the surround back channels for use in a multiroom system, speaker placement instructions for a 5.1-channel system for your main listening area (see page 19). The pair of speakers intended for the remote room in the multiroom system should be placed following the instructions for the front left/right speakers on page 19.

System Setup

Once the speakers have been placed in the room and connected,

the remaining steps in are to configure each source input to match the physical connections you have made, select a surround mode and run the EzSet/EQ procedure automatically program the AVR 340 for the type of speakers used in your system, calibrate the output levels, set the delay times used by the surround sound processor and perform room equalization to adapt the system to the unique characteristics of your listening area.

the setup process

which will

follow the

You are now ready to power up the AVR 340 to begin these final adjustments.

1. Make certain that the

AC Power Cord a is

firmly inserted into an unswitched AC outlet. To maintain the unit’s safety rating, DO NOT replace the power cord with one that has a lower current capacity.

2. Press the

Main Power Switch 1 in until it

latches and the word “OFF” on the top of the switch disappears inside the front panel. Note

Power Indicator 2 will turn amber,

that the

ndicating that the unit is in the Standby mode.

3. Remove the protective plastic film from the frontpanel lens. If left in place, the film will affect the performance of your remote control.

4. Install the three supplied AAA batteries in the remote as shown. Be certain to follow the (+) and (–) polarity indicators that are on the top of the battery compartment.

5. Turn the AVR 340 on either by pressing the Standby/On Switch 2 on the front panel, or via the remote by pressing the

Power On Button d, the AVR Selector f∫or any of the Input Selectors degde

∂

. When the unit is turned

list of options will briefly light for both

Indicators Indicators

Ú and the Surround Mode ˆ. After a few seconds, the majority

of those indicators will go dark,

on, the entire

the Input

leaving only the indications for the active surround mode and input illuminated. The display the unit’s status, the

Display Lines Ùı will

Power Indicator 2

will turn blue, and the accent light inside the Volume Control Ò will also light up to remind you that the unit is turned on.

Using the On-Screen Display

When making the following adjustments, you may find it easier to use the AVR 340’s on-screen display sys-

These easy-to-read displays give you a clear pic

tem. ture of the current status of the unit and make it easy to see which selection you are making.

To view the on-screen menus, make certain that you have made a connection from the

Monitor Out Jack

gY on the rear panel to the composite or S-video input of your or that you have made a connection from the

Component Video Monitor Outputs F on the

Video or S-Video

TV or projector

AVR 340 to your TV and that you are not using a high-definition (720p or better) video source. In order to view the AVR 340’s displays, the correct video

ource must be selected on the video display.The on-

creen menus are available when a component video

s display is in use, but only with 480p video sources.

IMPORTANT NOTE: When viewing the on-screen menus using a CRT-based projector, plasma display or any direct-view CRT monitor or television, it is important

hat they not be left on the screen for an extended period

t of time.The constant display of a static image such as these menus or other still images may cause the image to be permanently “burned into” the projection tubes, plasma screen or CRT. This type of damage is not covered by the AVR 340 warranty and may not be covered by the projector/TV set’s warranty.

The AVR 340 has two on-screen display modes, “Semi-OSD” and “Full-OSD.” When making configuration adjustments, it is recommended that the full-OSD mode be used. This will place a menu on the screen, making it easier to view the available options.

NOTE: When a component video source is in use, the semi-OSD displays are not available.

Making Configuration Adjustments

The full-OSD system is available by pressing the OSD Button v. When this button is pressed, the MASTER MENU (Figure 1) will appear, and adjustments are made from the individual menus.

Figure 1

The semi-OSD system is also available, allowing you to make adjustments directly,

by pressing the appro priate buttons on the front panel or remote control for the specific parameter to be adjusted. For example, to change the digital input for any of the sources press the

Digital Select Button q and then

⁄/¤

press the list of options as they appear in the on-screen display

Upper Display Line P.

or the

o use the full-OSD menu system, press the

Button

⁄/¤

the

Buttons n to scroll through the

v. When the menu is on the screen, press

Buttons n until the on-screen ›cursor

is next to the item you wish to adjust, and then press

Set Button p to adjust that item. The menus

the will remain on the screen for 20 seconds, and then they will

“time-out”

and disappear from

SYSTEM CONFIGURATION 21

OSD

the screen.

The

+ 47 hidden pages