Table Top Kettles
Description
Unit shall consist of . . . (Specify Model, Size & Quantity)
steam jacketed kettle(s) mounted on a . . . (Specify table
width in inches) T5C Table, per bulletin 141043 and as
follows:
Construction
Table shall be constructed of stainless steel with solid
one piece welded construction. Table top to have raised
marine edges and a 5” wide by 4” deep drain trough
running the width of the table, complete with drain fitting
and strainer.
Support legs are heavy 2” round tubular stainless steel
with adjustable bullet feet. Table top work height ideal for
operator convenience and efficiency.
Finish
All table and dump tray surfaces polished to a uniform #3
finish to insure maximum ease in cleaning.
model T5C
T5C shown with
two TDC/2-20 kettles
Stainless Steel
Equipment Table
For Mounting Table
Top Steam Jacketed
Kettles
Short Form
Unit shall be . . . (Specify
Model, Size & Quantity) Steam
jacketed kettle(s) mounted on
a . . . (Specify table width)
T5C Table per Bulletin 141043.
Kettle mounting table shall
be all stainless steel with
convenient work height and
5” wide drain trough with
removable sliding dump tray.
Front mounted individual
steam control valves provided
with direct steam kettles and
hot & cold water controls
standard. Swing faucet
positioned to fill one or two
kettles as needed. NSF listed.
Single point stream, hot & cold
water and drain connections
required. Made in USA.
Sanitation
Table shall have easy to clean open leg design and meet
known health department and sanitation codes, and be
NSF listed.
Dump Tray
Sliding dump tray is designed to assist in pouring kettle
contents into pans or pots. Splashes or drips are diverted
into the drain trough to eliminate spilling or splashing on
floors etc. Dump tray lifts out for easy cleanup and rolls
along length of drain trough on nylon rollers, to serve all
kettles mounted.
Controls
Front mounted steam control valves provided for each
direct steam kettle mounted. All necessary traps, piping
and valves furnished and prepiped for single point utility
connection, when direct steam kettles are mounted.
Water Fill Faucet
Table comes standard with double pantry faucet for
each two kettles mounted. Front mounted hot and cold
faucet valves and swing spouts simplify kettle filling and
cleaning.
Installation
T5C table with direct steam kettles require single stream,
hot & cold water and drain connections. See kettle
specifications sheet for self-contained kettle electric
and/or gas installation requirements.
Options
Wall mounting is available (Specify Model MWT5C).
Origin of Manufacture
Equipment table made in the United States.
Applications
Provide convenient and
proper operator / kettle
work height.
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most
updated product information and specifications.
Provide easy to clean work
station with built-in pouring
sink, fill faucet and kettle
controls.
Groen Table Top Kettles, Page 9
141043C
Revised 08/09
Model T5C
P/N D-9475-33 REV B
MM
584
737
HEIGHT
232530(1) TDA/1-40
IN.
MM
508
584
DEPTH
IN.
TABLE DIMENSIONS
MM
508
762
LENGTH
IN.
NUMBER / SIZE OF
KETTLES TO BE MOUNTED
(1) TDC/3-10 OR 20 20 23 29
584
737
737
232563(2) TDA/1-40'S
292340(2) TDC/3-20'S
292340(2) TDC/3-10'S
508
508
584
1016
1600
1016
584
584
737
737
232548
232590(3) TDA/1-40'S
292363(3) TDC/3-20'S
292363(3) TDC/3-10'S
508
508
584
584
2286
1600
1600
1219
(1) TDC/3-20 & (1) TDA/1-40
584
232366
508
1676
(2) TDC/3-20'S & (1) TDA/1-40
POSITION
FULL TILT
7.5"
(191)
1-1/8
5
(29)
4
2
3
BULLET FEET
FINISHED FLOOR
W/ MOUNTING TABS
DRAIN FOR SINK:1-1/2" IPS
COLD WATER SUPPLY:
1
2
SERVICE CONNECTIONS FOR KETTLES:
DRAIN CONDENSATE: 1/2" NPT
3/8" NPT (FOR FAUCET)
3/8" NPT (FOR FAUCET)
HOT WATER SUPPLY:
STEAM IN FROM POWER SOURCE: 1/2" NPT
3
5
4
NOTES:
OF KETTLES.
1. T-BRACE REQ'D ON ALL TABLES 60" AND LONGER.
2. 6 LEGS REQ'D ON 70" LONG TABLES AND LONGER.
4. DIMENSIONS IN BRACKETS ( ) ARE MM.
3. TABLE SIZE VARIES WITH TYPE AND NUMBER
SHOWN ARE THREE
TDC/3-20 KETTLES.
CONTACT GROEN FOR
OTHER CONFIGURATIONS
OF TABLE TOP KETTLES
ARE AVAILABLE.
HOT & COLD
WATER VALVES
SPECIFIC CONFIGURATIONS.
7-1/4
(184)
TYP.
6"
(152)
322 3
4
SPLASH
GUARD
MOVABLE
A
14"
(357)
SEE NOTE 2.
5
DRAIN &
STRAINER
1
6"
(152)
C
(397)
15-5/8"
SWING SPOUT
FAUCET
TYP.
17-1/8
RIM
HEIGHT
STEAM
VALVE
TYP.
SEE NOTE 1.
B
121501 REV.B
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net
© 2009 Unified Brands. All Rights Reserved. DOVER® and the DOVER® Logo are registered
trademarks in the United States [and various other countries] of Unified Brands, a
wholly-owned subsidiary of Dover Corporation.