Thank you for your purchase of this product. This
manual describes how to use your FUJIFILM X-Pro1
digital camera and install the supplied software. Be
sure that you have read and understood its contents
before using the camera.
For information on related products, visit our website at
• Read Instructions: All the safety and operating instructions
should be read before the appliance is operated.
• Retain Instructions: The safety and operating instructions
should be retained for future reference.
• Heed Warnings: All warnings on the appliance and in the
operating instructions should be adhered to.
• Follow Instructions: All operating and use instructions
should be followed.
Installation
Power Sources: This video product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For video products intended to operate from battery
power, or other sources, refer to the operating instructions.
Grounding or Polarization: This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fi t into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fi t, contact your electrician to replace your obsolete outlet. D o not defeat the safety
purpose of the polarized plug.
Alternate Warnings: This video product is equipped with
a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fi t into a grounding-type
power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding type plug.
Overloading: Do not overload wall outlets and extension
cords as this can result in a risk of fi re or electric shock.
Ventilation: Slots and openings in the cabinet are provided
for ventilation, to ensure reliable operation of the video
product and to protect it from overheating, and these openings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface.
ii
IMPORTANT SAFETY INSTRUCTIONS
This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been
adhered to. This video product should never be placed near
or over a radiator or heat register.
Attachments: Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
Water and Moisture: Do not use this video product near water—for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
Power-Cord Protection: Power-supply cords should be routed
so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
Accessories: Do not place this video product on an unstable
cart, stand, tripod, bracket, or table. The video product may
fall, causing serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the video product. Any mounting of the appliance
should follow the manufacturer’s instructions, and should use
a mounting accessory recommended by the manufacturer.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Antennas
Outdoor Antenna Grounding: If an outside antenna or cable
system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Electric Service
Equipment
Ground
Clamps
Power Service Grounding Electrode
System (NEC ART 250. PART H)
Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
Use
Cleaning: Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Object and Liquid Entry: Never push objects of any kind into this
video product through openings as they may touch dangerous
voltage points or short out parts that could result in a fi re or electric shock. Never spill liquid of any kind on the video product.
Lightning: For added protection for this video product receiver during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
Antenna Lead
in Wire
Antenna
Discharge Unit
(NEC SECTION
810-20)
Grounding Conductors
(NEC SECTION 810-21)
Service
Service
WARNING
WARNING
Servicing: Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualifi ed service personnel.
Damage Requiring Service: Unplug this video product from
the wall outlet and refer servicing to qualifi ed service personnel under the following conditions:
• When the power-supply cord or plug is damaged
• If liquid has been spilled, or objects have fallen into the
video product.
• If the video product has been exposed to rain or water.
• If the video product has been dropped or the cabinet has
been damaged.
If the video product does not operate normally follow the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment of other controls may result in damage and will often
require extensive work by a qualifi ed technician to restore
the video product to its normal operation.
When the video product exhibits a distinct change in performance — this indicates a need for service.
Replacement Parts: When replacement parts are required,
be sure the service technician has used replacement parts
specifi ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fi re, electric shock or other hazards.
Safety Check: Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
Be sure to read these notes before use
Safety Notes
• Make sure that you use your camera correctly. Read these
safety notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
The icons shown below are used in this document to indicate the severity of the injury or damage that can result if the
information indicated by the icon is ignored and the product
is used incorrectly as a result.
WARNING
CAUTION
The icons shown below are used to indicate the nature of the
instructions which are to be observed.
Triangular icons tell you that this information requires attention (“Important”).
Circular icons with a diagonal bar tell you that the
action indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an
action that must be performed (“Required”).
Unplug
from power
socket
About the Icons
This icon indicates that death or serious injury can result if the information
is ignored.
This icon indicates that personal injury
or material damage can result if the information is ignored.
WARNING
If a problem arises, turn the camera o , remove the
battery, and disconnect and unplug the AC power
adapter. Continued use of the camera when it is
emitting smoke, is emitting any unusual odor, or
is in any other abnormal state can cause a fi re or
electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the
camera. If water or foreign objects get inside the
camera, turn the camera off , remove the battery,
and disconnect and unplug the AC power adapter. Continued use of the camera can cause a fi re
or electric shock. Contact your FUJIFILM dealer.
For Your Safety
WARNING
Do not use the camera in the bathroom or shower. This
Do not use in
can cause a fi re or electric shock.
the bathroom
or shower
Never attempt to change or take apart the camera
(never open the case). Failure to observe this pre-
Do not disas-
caution can cause fi re or electric shock.
semble
Should the case break open as the result of a fall or other
accident, do not touch the exposed parts. Failure to ob-
serve this precaution could result in electric shock
or in injury from touching the damaged parts. Re-
Do not touch
internal
move the battery immediately, taking care to avoid
parts
injury or electric shock, and take the product to the
point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection
cord and do not place heavy objects on the connection
cord. These actions could damage the cord and
cause a fi re or electric shock. If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This
can cause the camera to fall or tip over and cause
injury.
Never attempt to take pictures while in motion. Do
not use the camera while walking or driving. This
can result in you falling down or being involved in
a traffi c accident.
Do not touch any metal parts of the camera during a
thunderstorm. This can cause an electric shock due
to induced current from the lightning discharge.
Do not use the battery except as speci ed. Load the
battery as shown by the indicator.
Do not heat, change or take apart the battery. Do not
drop or subject the battery to impacts. Do not store the
battery with metallic products. Any of these actions
can cause the battery to burst or leak and cause
fi re or injury as a result.
iii
For Your Safety
WARNING
CAUTION
CAUTION
Li-ion Batteries
iv
WARNING
Use only batteries or AC power adapters speci ed for
use with this camera. Do not use voltages other than
the power supply voltage shown. The use of other
power sources can cause a fi re.
If the battery leaks and uid gets in contact with your
eyes, skin or clothing, ush the a ected area with clean
water and seek medical attention or call an emergency
number right away.
Do not use the charger to charge batteries other than those
speci ed here. The supplied charger is for use only
with batteries of the type supplied with the camera.
Using the charger to charge conventional batteries
or other types of rechargeable batteries can cause
the battery to leak, overheat or burst.
Do not use in the presence of ammable objects, explosive gases, or dust.
When carrying the battery, install it in a digital camera or keep it in the hard case. When storing the bat-
tery, keep it in the hard case. When discarding, cover
the battery terminals with insulation tape. Contact
with other metallic objects or batteries could
cause the battery to ignite or burst.
Keep memory cards out of the reach of small children.
Because memory cards are small, they can be
swallowed by children. Be sure to store memory
cards out of the reach of small children. If a child
swallows a memory card, seek medical attention
or call an emergency number.
Do not use this camera in locations a ected by oil
fumes, steam, humidity or dust. This can cause a fi re
or electric shock.
Do not leave this camera in places subject to extremely
high temperatures. Do not leave the camera in loca-
tions such as a sealed vehicle or in direct sunlight.
This can cause a fi re.
Keep out of the reach of small children. This product
could cause injury in the hands of a child.
CAUTION
CAUTION
Do not place heavy objects on the camera. This can
cause the heavy object to tip over or fall and
cause injury.
Do not move the camera while the AC power adapter
is still connected. Do not pull on the connection cord
to disconnect the AC power adapter. This can dam-
age the power cord or cables and cause a fi re or
electric shock.
Do not cover or wrap the camera or the AC power
adapter in a cloth or blanket. This can cause heat
to build up and distort the casing or cause a fi re.
When you are cleaning the camera or you do not plan
to use the camera for an extended period, remove
the battery and disconnect and unplug the AC power
adapter. Failure to do so can cause a fi re or elec-
tric shock.
When charging ends, unplug the charger from the
power socket. Leaving the charger plugged into
the power socket can cause a fi re.
Using a ash too close to a person’s eyes may temporarily a ect the eyesight. Take particular care when
photographing infants and young children.
When a memory card is removed, the card could come
out of the slot too quickly. Use your nger to hold it and
gently release the card. Injury could result to those
struck by the ejected card.
Request regular internal testing and cleaning for your
camera. Build-up of dust in your camera can cause
a fi re or electric shock. Contact your FUJIFILM
dealer to request internal cleaning every two
years. Please note that this service is not free of
charge.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Note: Check the type of battery used in your camera and
read the appropriate sections.
The following describes the proper use of batteries and how
to prolong their life. Incorrect use can shor ten battery life or
cause leakage, overheating, fi re, or explosion.
Li-ion Batteries
Read this section if your camera uses a rechargeable
Li-ion battery.
The battery is not charged at shipment. Charge the battery
before use. Keep the batter y in its case when not in use.
The battery gradually loses its charge when not in use.
Charge the battery one or two days before use.
Battery life can be extended by turning the camera off when
not in use.
Battery capacity decreases at low temperatures; a depleted
battery may not function at when cold. Keep a fully charged
spare battery in a warm place and exchange as necessary,
or keep the battery in your pocket or other warm place and
insert it in the camera only when shooting. Do not place
the battery in direct contact with hand warmers or other
heating devices.
Charge the battery in the supplied battery charger. Charging
times will increase at ambient temperatures below +10 °C
(+50 °F) or above +35 °C (+95 °F). Do not attempt to charge
the battery at temperatures above 40 °C (+104 °F); at temperatures below 0 °C (+32 °F), the batter y will not charge.
Do not attempt to recharge a fully charged battery. The battery does not however need to be fully discharged before
charging.
The battery may be warm to the touch immediately after
charging or use. This is normal.
At normal temperatures, the battery can be recharged about
300 times. A noticeable decrease in the length of time the
battery will hold a charge indicates that it has reached the
The Battery and Power Supply
■ Notes on the Battery
■ Charging the Battery
■ Battery Life
end of its service life and should be replaced.
AA Alkaline/Rechargeable Ni-MH Batteries
AC Power Adapters (Available Separately)
■ Storage
Performance may be impaired if the battery is left unused
for extended periods when fully charged. Run the battery
fl at before storing it.
If the camera will not be used for an extended period, remove the battery and store it in a dry place with an ambient
temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of temperature.
■ Cautions: Handling the Battery
• Do not transport or store with metal objects such as necklaces or hairpins.
• Do not expose to fl ame or heat.
• Do not disassemble or modify.
• Use with designated chargers only.
• Dispose of used batteries promptly.
• Do not drop or subject to strong physical shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become warm to the
touch after extended use. This is normal.
AA Alkaline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA alkaline or rechargeable AA Ni-MH batteries. Information on compat-
ible battery types may be found elsewhere in the camera
manual.
■ Cautions: Handling the Batteries
• Do not expose to water, fl ame, or heat, or store in warm or
humid conditions.
• Do not transport or store with metal objects such as necklaces or hairpins.
• Do not disassemble or modify the batteries or battery
casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discolored.
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
• Do not mix old and new batteries, batteries with diff erent
charge levels, or batteries of diff erent types.
• I f the camera will not be used for an extended period, re-
move the batteries. Note that the camera clock will be reset.
• The batteries may be warm to the touch immediately after
use. Turn the camera off and allow the batteries to cool
before handling.
• Battery capacity tends to decrease at low temperatures.
Keep spare batteries in a pocket or other warm place and
exchange as necessary. Cold batteries may recover some
of their charge when warmed.
• Fingerprints and other stains on the battery terminals
can impair battery performance. Thoroughly clean the
terminals with a soft, dry cloth before inserting them in
the camera.
If the batteries leak, clean the battery compartment
thoroughly before inserting new batteries.
If fl uid from the battery comes into contact with
skin or clothing, fl ush the aff ected area with water.
If uid enters your eyes, immediately ush the a ec ted
area with water and seek medical attention. Do not rub
your eyes. Failure to observe this precaution could result
in permanent visual impairment.
■ Ni-MH Batteries
The capacity of Ni-MH batteries may be temporarily reduced
when new, after long periods of disuse, or if they are repeatedly recharged before being fully discharged. This is normal and does not indicate a malfunction. Capacity can be
increased by repeatedly discharging the batteries using the
discharge option in the camera setup menu and recharging
them using a battery charger.
Q C AUTION: Do not use the discharge option with alkaline
batteries.
The camera draws a small amount of current even when off .
Ni-MH batteries that have been left in the camera for an extended period may be drawn down to the point that they no
longer hold a charge. Battery performance may also drop if
the batteries are run down in a device such as a fl ashlight. Use
the discharge option in the camera setup menu to discharge
Ni-MH batteries. Batteries that no longer hold a charge
even after repeatedly being discharged and recharged have
reached the end of their service life and must be replaced.
Ni-MH batteries can be recharged in a battery charger (sold separately). Batteries may become warm to the touch after charg-
For Your Safety
ing. Refer to the instructions provided with the charger for more
information. Use the charger with compatible batteries only.
Ni-MH batteries gradually lose their charge when not in use.
■ Disposal
Dispose of used batteries in accord with local regulations.
AC Power Adapters (Available Separately)
This section applies to all camera models. Use only
FUJIFILM AC power adapters designated for use with this
camera. Other adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected to the camera.
• Turn the camera off before disconnecting the adapter. Disconnect the adapter by the plug, not the cable.
• Do not use with other devices.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the touch during
use. This is normal.
• If the adapter causes radio interference, reorient or relocate
the receiving antenna.
v
For Your Safety
Take Test Shots
Notes on Copyright
Handling
Liquid Crystal
Trademark Information
Electrical Interference
Color Television Systems
Electrical Interference
Do not aim the camera at extremely bright light sources,
such as the sun in a cloudless sky. Failure to observe this
precaution could damage the camera image sensor.
Take Test Shots
Before taking photographs on important occasions (such as
at weddings or before taking the camera on a trip), take a
test shot and view the results to ensure that the camera is
functioning normally. FUJIFILM Corporation can not accept
liability for damages or lost profi ts incurred as a result of
product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded using your digital camera system cannot be used in ways that
infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the photographing of
stage performances, entertainments, and exhibits, even
when intended purely for personal use. Users are also asked
to note that the transfer of memory cards containing images
or data protected under copyright laws is only permissible
within the restrictions imposed by those copyright laws.
Handling
To ensure that images are recorded correctly, do not subject
the camera to impact or physical shocks while images are
being recorded.
Liquid Crystal
In the event that the display is damaged, care should be
taken to avoid contact with liquid crystal. Take the urgent
action indicated should any of the following situations arise:
• If liquid crystal comes in contact with your skin, clean the
area with a cloth and then wash thoroughly with soap and
running water.
• If liquid crystal enters your eyes, fl ush the aff ected eye with
clean water for at least 15 minutes and then seek medical
assistance.
• If liquid crystal is swallowed, rinse your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting, then seek medical assistance.
Using the Camera
Although the display is manufactured using extremely highprecision technology, it may contain pixels that are always lit
or that do not light. This is not a malfunction, and images
recorded with the product are unaff ected.
Trademark Information
xD-Picture Card and E are trademarks of FUJIFILM
Corporation. The typefaces included herein are solely developed by DynaComware Taiwan Inc. Macintosh, QuickTime, and Mac OS are trademarks of Apple Inc. in the U.S.A.
and other countries. Windows 7, Windows Vista, and the
Windows logo are trademarks of the Microsoft group of
companies. Adobe and Adobe Reader are either trademarks
or registered trademarks of Adobe Systems Incorporated in
the U.S.A. and/or other countries. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo is a trademark.
YouTube is a trademark of Google Inc. All other trade names
mentioned in this manual are the trademarks or registered
trademarks of their respective owners.
Electrical Interference
This camera may interfere with hospital or aviation equipment. Consult with hospital or airline staff before using the
camera in a hospital or on an aircraft.
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specifi cation adopted mainly in the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in European countries and China.
Electrical Interference
Exif Print is a newly revised digital camera fi le format in
which information stored with photographs is used for optimal color reproduction during printing.
IMPORTANT NOTICE: Read Before Using the Software
Direct or indirect export, in whole or in part, of licensed software without the permission of the applicable governing
bodies is prohibited.
vi
To prevent re or shock hazard, do not expose the unit
For Customers in the U. S. A.
For Customers in Canada
Disposal of Electrical and Electronic Equipment in Private
Households
NOTICES
to rain or moisture.
Please read the “Safety Notes” and make sure you understand them before using the camera.
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement: This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
• You are cautioned that any changes or modifi cations not
expressly approved in this manual could void the user’s
authority to operate the equipment.
Notes on the Grant: To comply with Part 15 of the FCC Rules,
this product must be used with a Fujifi lm-specifi ed ferritecore A/V cable, USB cable, and DC supply cord.
For Customers in Canada
CAUTION: This Class B digital apparatus complies with Canadian ICES-003.
Disposal of Electrical and Electronic Equipment in Private
Households
In the European Union, Norway, Iceland and Liechtenstein: This symbol on the product, or in the man-
ual and in the warranty, and/or on its packaging
indicates that this product shall not be treated as
household waste. Instead it should be taken to
an applicable collection point for the recycling
of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences to the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
This symbol on the batteries or accumulators indicates that those batteries shall not be treated
as household waste.
If your equipment contains easy removable batteries or
accumulators please dispose these separately according to
your local requirements.
The recycling of materials will help to conserve natural resources. For more detailed information about recycling this
product, please contact your local city offi ce, your household
waste disposal service or the shop where you purchased the
product.
In Countries Outside the European Union, Norway, Iceland and
Liechtenstein: If you wish to discard this product, including
the batteries or accumulators, please contact your local authorities and ask for the correct way of disposal.
Optional ash units ......................................................54, 97
■ Custom Settings
Assigning a role to the Fn button ................................50
Saving and recalling settings .........................................52
x
Product Care
Product Care
Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body
after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform
the leather on the camera body. Any liquid on the camera should be removed immediately with a
soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then
gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece
of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning uid has been applied. To
prevent dust entering the camera, replace the body cap when not lens is in place.
Image sensor: Dust can be removed from the image sensor using the V SENSOR CLEANING option in
the setup menu (P 82).
Lenses: Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can
be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of
lens-cleaning uid has been applied. Replace the front and rear caps when the lens is not use.
xi
Table of Contents
Table of Contents
Before You Begin
First Steps
Taking Photographs
For Your Safety .....................................................................................ii
IMPORTANT SAFETY INSTRUCTIONS .........................................ii
Restrictions on Camera Settings ............................................ 116
xvi
Before You Begin
Before You Begin
Symbols and Conventions
Supplied Accessories
Symbols and Conventions
The following symbols are used in this manual:
Q This information should be read before use to ensure correct operation.
R Additional information that may be helpful when using the camera.
P Other pages in this manual on which related information may be found.
Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may
be simpli ed for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-W126 rechargeable batteryBC-W126 battery charger Body capUSB cable
• Owner’s Manual (this
manual)
• Shoulder strap
• Protective covers (× 2)
CD-ROMClip attaching toolMetal strap clips (× 2)
• Diopter adjustment lens
(comes installed in camera)
Before You Begin
1
Parts of the Camera
Parts of the Camera
For more information, refer to the page listed to the right of each item.
Press the selector up (q), right
(w), down (e), or left (r) to
highlight items and press MENU/OK (t) to select. Pressing the
selector up (MACRO) during
shooting displays macro options (P 31).
Control Lock
To avoid accidentally displaying macro options during shooting, press MENU/OK until X is displayed. The
control can be unlocked by pressing MENU/OK until X
is no longer displayed.
The Command Dial
The command dial can be used to navigate the menus, to view the most recent picture (P 56), and to select options in the quick menu display (P 5).
Press the center of the command dial
to zoom in on the focus area selected
for manual focus (P 46) or the active focus point during playback (P 57).
4
The
The QQ
(Quick Menu) Button
Option
P
u u SELECT CUSTOM SETTING
52
N
48
U
68
D
32
h
69
O
67
Option
P
T
67
P
51
rr HIGHLIGHT TONE
69
ss SHADOW TONE
69
f f COLOR
68
qq SHARPNESS
69
Option
P
B B SELF-TIMER
41
F F AF MODE
69
I I FLASH MODE
54
JJ LCD BRIGHTNESS
81
(Quick Menu) Button
Press Q for quick access to the following items:
Option
SELECT CUSTOM SETTING
N
ISO
U
DYNAMIC RANGE
D
WHITE BALANCE
h
NOISE REDUC TION
O
IMAGE SIZE
Press Q to display the quick menu during shooting.
1
Use the selector to highlight items and rotate the command dial to change.
2
Press Q to exit when settings are complete.
3
P
52
T
48
P
68
32
69
67
IMAGE QUALITYFILM SIMULATION
HIGHLIGHT TONE
SHADOW TONE
COLOR
SHARPNESS
R For quick access to custom settings banks, press and hold the Q button.
Option
P
67
51
69
69
68
69
SELF-TIMER
AF MODE
FLASH MODE
LCD BRIGHTNESS
Parts of the Camera
Option
P
41
69
54
81
Before You Begin
5
Parts of the Camera
Camera Displays
View nder Focus
Camera Displays
The following types of indicator may be displayed during shooting and playback. Indicators vary with
camera settings.
Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
1
Use the clip attaching tool to open a strap clip
as shown.
Q Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
Place the strap clip on an eyelet.
2
Hook the strap eyelet in the clip opening. Remove the tool, using the other hand to keep
the clip in place.
Pass the clip through the eyelet.
3
Rotate the clip fully through
the eyelet until it clicks
closed.
Attach a protective cover.
4
Place a protective cover over the eyelet as
shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second
eyelet.
First Steps
9
Attaching the Strap
Insert the strap.
5
Insert the strap through a protective cover
and strap clip.
Fasten the strap.
6
Fasten the strap as shown. Repeat Steps 5–6
for the second eyelet.
Q To avoid dropping the camera, be sure the strap is
correctly secured.
10
Attaching a Lens
Attaching a Lens
Removing Lenses
Supported Lenses (
96)
Lenses attach as described below.
Q Care is required to prevent dust entering the camera while attaching and removing lenses.
Remove the body and rear caps.
1
Remove the body cap from the camera and
the rear cap from the lens.
Q Do not touch the camera’s internal parts.
Attach the lens.
2
Place the lens on mount, keeping the marks
Removing Lenses
To remove the lens, turn the
camera o , then press the
lens release button and rotate
the lens as shown.
Q To prevent dust accumulating inside the camera, replace
the body cap when no lens is attached.
Supported Lenses (PP
The camera can be used with optional XF18mmF2 R,
XF35mmF1.4 R, and XF60mmF2.4 R Macro interchangeable lenses.
96)
on the lens and camera aligned, and then rotate the lens until it clicks into place.
Q Do not press the lens release button while at-
taching the lens.
Lens release button
First Steps
11
Charging the Battery
Charging the Battery
The Charging Indicator
Charging
indicator
Battery status
Action
O
Battery not
inserted.
Insert the battery.
Battery fully
charged.
Remove the battery.
OnOnBattery charging.
—
Blinks
Battery fault.
Unplug the charger
and remove the
battery.
The battery is not charged at shipment. Charge the battery before use.
Place the battery in the charger.
1
Place the battery in the supplied battery charger as shown.
Charge lamp
Battery charger
Arrow
Battery
The camera uses an NP-W126 rechargeable battery.
Plug the charger in.
2
Plug the charger into a power outlet. The
charging indicator will light.
The Charging Indicator
The charging indicator shows battery charge status as follows:
Charging
indicator
O
Battery charging.
Blinks
Charge the battery.
3
Remove the battery when charging is complete. See the speci cations (P 114) for charg-
ing times (note that charging times increase
at low temperatures).
Q Unplug the charger when it is not in use.
Battery status
Battery not
inserted.
Battery fully
charged.
Battery fault.
Action
Insert the battery.
Remove the battery.
—
Unplug the charger
and remove the
battery.
12
Inserting the Battery and a Memory Card
Inserting the Battery and a Memory Card
The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC
memory cards (sold separately). After charging the battery, insert the battery and memory card as
described below.
Open the battery-chamber cover.
1
Slide the battery-chamber latch as shown and
open the battery-chamber cover.
Insert the battery.
2
Insert the battery as shown inside the battery
chamber, using the battery to keep the battery latch pressed to one side.
Arrow
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could damage image les or memory cards.
Q Do not use excessive force when handling the
battery-chamber cover.
Q Insert the battery in the correct orientation. Do
not use force or attempt to insert the battery upside down or backwards. The battery will slide in
easily in the correct orientation.
Battery latch
First Steps
13
Inserting the Battery and a Memory Card
Insert the memory card.
3
Holding the memory
card in the orientation
shown at right, slide
it in until it clicks into
place at the back of
the slot.
Click
Q Be sure card is in the correct orientation; do not
insert at an angle or use force.
Q SD/SDHC/SDXC memo-
ry cards can be locked,
making it impossible to
format the card or to
record or delete images.
Before inserting a memory card, slide the writeprotect switch to the unlocked position.
Close the battery-chamber cover.
4
Write-protect switch
Slide the battery-chamber latch as shown and
close the battery-chamber cover.
14
Loading...
+ 106 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.