Fisher & Paykel DD90SDFTM2 User Manual

INSTALLATION INSTRUCTIONS

DishDrawer

DD90SDF(H)TX2, DD90SDFTM2 (Designer)

& DD90S(H)TI2 (Integrated) models

TM

dishwasher

NZ AU GB IE

590202B 12.11

1

DD90SDF(H)TX2
DD90SDFTM2

Designer

PRODUCT & CABINETRY

DIMENSIONS

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

CHOOSE

DRAINAGE OPTION

ADJUST PANEL HEIGHT

FINAL CHECKLIST

CONNECT TO WATER & ELECTRICITY

TROUBLESHOOTING

PRODUCT & CABINETRY

DIMENSIONS

DD90STI2

Integrated (Remote control)

CUSTOM FRONT

PANEL CALCULATIONS

PARTS SUPPLIED +

EXTERNAL VENTING KIT

ADJUST PANEL HEIGHT

CONNECT TO WATER & ELECTRICITY

CAVITY PREPARATION &

EXTERNAL VENTING

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

CHOOSE

DRAINAGE OPTION

INSTALL THE FRONT PANEL

FINAL CHECKLIST

TROUBLESHOOTING

FOLLOW STEPS

FOR THE

EXTERNAL

VENTING KIT

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

DD90SHTI2

Integrated (Badge control)

ADJUST PANEL HEIGHT

CONNECT TO WATER & ELECTRICITY

CHOOSE

DRAINAGE OPTION

FINAL CHECKLIST

TROUBLESHOOTING

PRODUCT & CABINETRY

DIMENSIONS

CUSTOM FRONT

PANEL CALCULATIONS

PARTS SUPPLIED

CAVITY PREPARATION

MAXIMUM DISTANCE OF HOSES

& CORD FROM CHASSIS EDGE

INSTALL THE FRONT PANEL

& BADGE CONTROLS

SECURE WITHOUT

DRAWER REMOVAL

RECOMMENDED

METHOD (a)

ALTERNATIVE

METHOD (b)

SECURE BY

DRAWER REMOVAL

FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL

2

ONLY AVAILABLE IN GB IEONLY AVAILABLE IN NZ AU

2a

95 lb

43 kg

SAFETY AND WARNINGS - ALL MODELS

3

WARNING!

Electrical shock hazard

Before installing the dishwasher, remove the house fuse or open the circuit

breaker.

This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The plug must be plugged
into an appropriate outlet that is installed and earthed in accordance with all
local codes and ordinances. WARNING- Improper connection of the equipment­earthing conductor can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt as to whether the
appliance is properly earthed.

Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.

Failure to follow this advice may result in electrical shock or death.

WARNING!

Cut hazard

Take care - panel edges are

sharp.

Failure to use caution could

result in injury or cuts.

WARNING!

Very Heavy

Do not attempt to lift this

product unassisted.

Lifting unassisted may

cause serious injury.

IMPORTANT SAFETY INSTRUCTIONS!

Installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the dishwasher installation, the Installer must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

The switched power outlet must be outside the dishwasher cavity, so that it is accessible after

installation.

Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord and hoses.
If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should

not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,

boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.

SAVE THESE INSTRUCTIONS

2b

ADDITIONAL SAFETY AND WARNINGS - INTEGRATED MODELS ONLY

WARNING!

Fitting integrated front panels requires access to electrical service areas.
This work must be performed and certified by a qualified electrical service technician.

Electrical Shock Hazard

WARNING: To reduce the risk of electrical shock, fire, or injury to persons, the
installer must ensure that the dishwasher is completely enclosed at the time of
installation.
Before fitting the front panel and connecting the integrated badges (where
present), the installer must ensure that the dishwasher is disconnected from the
power supply.
After installing the front panel, the installer must ensure that the following
components are electrically earthed: the panel bracket, the integrated badge
(where present) and any custom metal component (e.g. handle) that extends
past the rubber seal.

Failure to follow these warnings may result in electrical shock, injury or fire.

IMPORTANT SAFETY INSTRUCTIONS!

Read these instructions completely and carefully.
Ensure the product is not plugged in.
Installation of custom panels requires basic mechanical and electrical skills.
Installation must comply with your local building and electricity regulations.
Failure to install the custom panels correctly could invalidate any warranty or liability claims.

SAVE THESE INSTRUCTIONS

3a

PARTS SUPPLIED - ALL MODELS

4

Drain hose
support (1)

Drain hose
joiner (1)

Wire clip (1)

(for securing
Drain hose joiner)

Side mounting
bracket kit
(A and B) (2)

OPTIONAL

Clamp (1)

(for securing
Drain hose joiner)

Phillips
16 mm
screws (7)

38 mm
bottom
fixing screws
& metal
washers (2)

If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m.
The kit is available from the nearest Fisher & Paykel Authorised Service Centre or through our local website listed at the end of this document.

Rubber
washer for
inlet hose (1)

(comes
already
fitted)

Moisture
protection
tape (1)

(to prevent
moisture
damage)

3b

ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS

5

External Venting kit (1)

supplied with Integrated models
with remote (NZ AU) only

Panel bracket (1)

(attached to product)

Panel mounting
screws (14)

Integrated rectangular badge (1)

(Satin chrome supplied)

supplied with Integrated models
with badge (GB IE) only

4

PRODUCT DIMENSIONS

K

H

I

A

J

Product dimensions (mm)

Side

6

G

Plan

CD

F

B

E

Badge control

Integrated

Designer

control

Integrated

Remote

overall height1 of product (incl. front panel height) 478 478 478

A

overall width of product 895 min. 855 min. 855

B

overall depth of product (excl. handle) 571 571

C

depth of chassis (to back of front panel) 553 553 553

D

maximum extension of drawer (excl. handle) 545 545

E

depth of front panel (excl. handle) 18 16-20 16-20

F

height1 of chassis 458 458 458

G

depth of handle 41 n/a n/a

H

height of front panel 470 476

I

height of ventilation gap below front panel 8 min. 2 min. 8

J

height from top of handle to top of front panel 64 n/a n/a

K

1

includes 2 mm high bracket slots 2Assuming front panel thickness of 18 mm

3

Recommended for a 2 mm ventilation gap below front panel, if cavity height is 480 mm

2

2

3

571

545

470

2

2

5

CABINETRY DIMENSIONS

7

O
N

O
N

18 mm

LM

Cabinetry dimensions mm

Side

Designer

control

Integrated

Remote

P

Badge control

Plan

20 mm

2 mm

Minimum clearances from adjacent cabinetry

min. 13 mm
clearance from a
corner cupboard

Integrated

min. 2 mm
clearance
to adjacent
cupboard door

height of cavity

(from support surface to underside

L

of benchtop)

inside height of cavity 460 min. 460 min. 460

M

inside width of cavity 864 864 864

N

overall width of cabinetry 900 900 900

O

inside depth of cavity min. 560 min. 560 min. 560

P

*Recommended

480 480* 480*

6a

INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - CUSTOM FRONT PANEL CALCULATIONS

FRONT PANEL SPECIFICATIONS

16 -20 mm panel thickness
Adequately sealed to withstand moisture (50
Maximum weight of panel: 9 kg

The following calculations assume the top of the panel is aligned
with the top of the adjacent cabinetry:

O

C @ 80% RH)

WIDTH OF THE PANEL

min. 2mm

8

min. 2mm

A

min. 2mm

Measure
and write it in the  rst box below, then complete the equation.

A (

the width between adjacent door/drawer fronts)

clearance to

adjacent cabinet

A

front (min. 2 mm)

- 2x

=

WIDTH OF PANEL

(min. 855 mm)

HEIGHT OF THE PANEL

Measure B and write it in the  rst box below, then complete
the equation.

ventilation gap

-

(min. 2 mm)

B

Note: when the top of the dishwasher has to be lower than the adjacent
cabinetry, the panel can be increased in height.

HEIGHT OF PANEL

=

WIDTH OF PANEL

B

HEIGHT
OF PANEL

min. 2mm

min. 2mm ventilation
gap with external venting
kit installed

min. 2mm ventilation gap with

external venting kit installed