Fisher LO540 User Manual
L0540
Newborn Baby
Older Baby
Toddler
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.com/uk
Consumer Information
WARNING
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use this
product on an elevated surface, since
child’s movement may cause the product
to slide or tip over. Use only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffocation in soft surfaces.
• Never leave child unattended.
• Never use as a carrier or lift while
child is seated. Never use the toy bar
as a handle.
• Use the upright position only when
child has developed enough upper body
control to sit without leaning forward.
• Always use the restraint system until
child is able to climb in and out of the
product unassisted.
• Reclined position not recommended
for children who cannot sit up by themselves (6 months approximately,
until 9 Kg/20 lbs).
Parts
IMPORTANT! Please remove all parts from the package and
identify them before assembly.
Toy (Toy may
be different)
Pad with Seat Back Tube
Hint: Please refer to the care
section to remove the seat back
tube for cleaning.
Front Bar
Toy Bar
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
• Please read these instructions before assembly and use of this product.
• Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included).
• Requires one “D” (LR20) alkaline battery (not included) for soother
operation. Toy includes one non-replaceable button cell battery.
• Product features and decorations may vary from photographs.
2 Side Rails Crossbar
Note: Tighten or loosen the screws with a Phillips screwdriver.
Do not over-tighten the screws.
#4 x 20 mm Screws – 6
Shown Actual Size
2
2
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel
for replacement parts and instructions if needed. Never
substitute parts.
Crossbar
3
• Insert and "snap" the back rails into the sockets in the side rails.
Pull up on the back rails to be sure they are secure.
Side Rails
1
• Place the side rails on a flat surface.
• Fit the crossbar tabs into the small rectangular opening in each side
rail. Push the crossbar down completely.
• Insert two #4 x 20 mm screws into the crossbar and tighten.
PUSH
PUSH
LIFT
LIFT
2
• First lift the front rails and then push out the back rails.
Side Rails
Front Bar
4
Hint: You may want to install batteries into the soother before
assembling the front bar to the front rails.
• Position the front bar so that the soother is upright. Fit it to grooved
area on the inside of the front rails.
• Insert four #4 x 20 mm screws into the front rails and tighten.
Hint: You may need the help of another adult to hold the front
bar in place while you insert and fasten the screws.
3
Seat Back Tube
Socket
5
Assembly
Pad
Clips
Socket
7
• Fit the clips on the front edge of the pad to the bottom edge of the
front bar.
• Insert the ends of the seat back tube (inside the pad) into the
sockets in the front rail. Push down on the seat back tube until
you hear a “click” on each side.
• Pull up on the seat back tube to be sure it is secure.
Pocket
Hardboard
6
Buckle
Pad Flap
8
• Wrap a pad flap around a front rail and fasten the buckle. Make sure
you hear a “click”.
• Repeat this procedure to fasten the other pad flap.
• Locate the pocket in the bottom of the pad.
• Fit the hardboard (attached to the front bar) into the pocket in
the pad.
4
Loading...