FAAC DTG User Manual

DTG

SAFETY EDGE INPUT TERMINALS

TEST

SWITCH

CODE SWITCH

KEYS

9 VOLT ALKALINE OR LITHIUM BATTERY

ANTENNA

TEST

INDICATOR

ATTACH DTG TO PLATE

3.88"

1.77"

WELD PLATE

TO GATE

GATE SAFETY EDGE TRANSMITTER

Installation Instructions

(800) 421-1587 • www.linearcorp.com

DESCRIPTION

The DTG is part of Linear’s Delta-3 product line and is compatible with all Delta-3 products. In a typical installation, the DTG is mounted on a motorized gate, door or barrier arm and wired to a standard exterior safety edge sensor which presents a closed circuit across the connecting wires when an object is hit during the closing of a gate. To insure full compatibility with all gate edge safety features, Linear recommends Miller gate edge sensors. If the edge sensor is pressed for a minimum of 1/8 second, the DTG transmits a message to the receiver to reverse the movement of the gate. The DTG circuit board has been coated to prevent moisture damage and is mounted inside a weather resistant fiberglass box. The mounting box attaches to the gate through sealed interior mounting screws.

TYPICAL

INSTALLATION

STEP 1

remove cover.

Remove Cover.

REMOVE

COVER

DTG

TRANSMITTER

SAFETY EDGE

SENSOR

Loosen the four screws on transmitter top and

LOOSEN

SCREWS

STEP 2

and details.

Locate Parts.

GATE

OPERATOR

Refer to diagram below for transmitter parts location

STEP 3

instructions included with the product.

Mount Safety Edge.

Mount safety edge according to manufacturer’s

INSTALL SAFETY EDGE

STEP 4

secure position. Use the template attached to mark the location for the transmitter. You may have to attach a metal or wood plate to mount transmitter. Use a 3/32" bit and drill holes. Attach DTG to gate using the four #6 self-tapping drill point screws.

Mount DTG.

Choose a location as high as possible on gate in a

STEP 5

Assemble Cable Grip.

Unscrew the cable grip about 3/4 of the way

and thread the safety edge cable through the cable entry on the transmitter.

TO SAFETY EDGE

STEP 6

Attach Cable.

Attach safety edge cable to terminals as shown.

Tighten cable grip assembly using pliers to assure a water tight seal.

ATTACH EDGE SENSOR CABLE TO TERMINALSTO SAFETY EDGE

STEP 7

DTG Code Setting.

To set a code, select any valid combination of ON and OFF positions for the switch keys numbered 1 - 8. Refer to receiver installation instructions to code receiver switches.

USE A PAPER CLIP TO SET THE EIGHT KEYS

STEP 9

Wire Receiver.

Wire receiver obstacle output to obstacle input on

operator. Refer to operator and receiver wiring instructions.

GATE OPERATOR

DRG

Digital Gate Receiver

CHANNEL

ONE

GRAY

MANUAL ACCESS REQUEST

COMMON

RELAY

24 V RADIO POWER

OBSTACLE INPUT

YELLOW

CHANNEL

TWO

COMMON OBSTACLE

STEP 8

Test Safety Edge.

Test safety edge connection by pressing the

safety edge. The test indicator light should come on.

TEST INDICATOR SHOULD LIGHT WHEN SAFETY EDGE IS PRESSED

PRESS WITH HAND

STEP 10

Test System.

Activate the gate to close. As the gate is closing, press

the safety edge with your hand. Gate should stop and reverse.

☞

CAUTION! DO not stand in the path of the closing gate.

PRESS SAFETY EDGE

WARNING! NO AUTOMATIC SUPERVISION OF A DAMAGED GATE EDGE SENSOR IS PROVIDED. USER IS CAUTIONED TO TEST THE TRANSMITTER REGULARLY.

CLOSE GATE

STEP 11

Replacing Batteries.

If LED indicator fails to light when test button

is pushed, replace with a 9 volt alkaline or lithium battery.

UNSNAP

BATTERY CLIP

WARNING! NO LOW BATTERY REPORTS ARE SENT WHEN THE BATTERY GETS WEAK. USER IS CAUTIONED TO TEST THE TRANSMITTER MONTHLY.

REMOVE BATTERY

FROM HOLDER

This product is warranted to the consumer against defects in material and workmanship for one year from the date of purchase. This warranty applies to first retail buyers of new dev ices. Warrantor will repair, or at its option, replace, any device it finds that requires service under this warranty, and will return t he repaired or repla ced device to the con sumer at the warrantor’s cost. For warranty service and shipping inst ructions contact warrantor at the addr ess shown below. Devices must be sent to warrantor for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied warranties under state law are to the one year period of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.

✶

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

✶

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio s ignals that occur on or near their operating frequencies, regardless of code settings.

✶

Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against undet ected int erf erence or fau lt.

✶

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

LIMITED WARRANTY

IMPORTANT !!!